Trademarks 1.

Checklist
CTS is a registered trademark of Connection Technology The package should contain the following items:
Systems Inc. Contents subject to revision without prior notice.
- CVT-3002-PLUS Converter
All other trademarks remain the property of their owners. - AC-DC Power Adapter
- User’s Guide
Copyright Statement Please notify your sales representative immediately if any items
Figure 1. CVT-3002-PLUS Dual Fiber Front Panel

Copyright  Connection Technology Systems Inc. are missing or damaged.

This publication may not be reproduced as a whole or in part, in 2. Overview

any way whatsoever unless prior consent has been obtained
from Connection Technology Systems Inc. CVT-3002-PLUS is designed to meet the massive needs for
Gigabit network deployment and able to extend a copper based
Gigabit network via fiber cable to a maximum distance up to
FCC Warning 40KM.
Figure 2. CVT-3002-PLUS WDM & SFP Front Panel
The CVT-3002-PLUS Series converters have been tested and
found to comply with the limits for a Class A digital device, CVT-3002-PLUS is fully compliant with IEEE 802.3, 802.3u,
pursuant to Part 15 of the FCC Rules. These standards are 802.3ab, 802.3z, and 802.3x standards. It can be installed into a
designed to provide reasonable protection against harmful CVT Converter RACK. The installation & operation procedures
interference when these devices are operated in a commercial are simple & straightforward. Operation status can be locally
environment. These devices generate, use, and can radiate monitored through a set of Diagnostic LED located in the front
radio frequency energy and may cause harmful interference to panel.
radio communications unless installed in accordance with this
User’s Guide. Operation of these devices in a residential area Major Features:
is likely to cause harmful interference which will make the user Figure 3. CVT-3002-PLUS Converter Rear Panel
responsible for the appropriate remedial action at his / her own - Auto-Negotiation in TX and Fiber port
expense. - MDI/MDIX Auto-Crossover supported
- Support Flow Control and Back Pressure
- Support Link Alarm
CE Mark Warning - Support Jumbo Frame 9K bytes (under 10,100,1000Mbps)
4. DIP SWITCH Setting
- Store and Forward Switching Mechanism The default setting for PIN 1 and 6 is ON. The rest of Pins are
These are Class A products. In a domestic environment these
- Support Auto & Force mode configuration OFF.
products may cause radio interference in which case the user
will need to consider adequate preventative methods. Pin NO. Function OFF ON
3. Installation 1 TP Auto-Negotiation Disable Enable
2 Manual TP speed 10M 100M
 Attach fiber cable from the CVT-3002-PLUS to the fiber 3 Manual TP speed N/A 1000M
network. The fiber connections must be matched – transmit 4 Duplex mode Half Full
socket to receive socket. 5 Flow Control Disable Enable
 Attach a UTP cable from the 10/100/1000Base-T network 6 F/O mode Force Auto
to the RJ-45 port on the CVT-3002-PLUS. 7 Link Alarm Disable Enable
 Connect the power adapter to the CVT-3002-PLUS and 8 Reserved - -
check that the Power LED lights up. The TX Link/Act and NOTE:
F/O Link/Act LEDs will light up when all the cable 1. Before adjusting the configuration of the DIP Switch, the
connections are satisfactory.
power should be unplugged.
2. Before changing TP speed, duplex mode and flow
control setting, please make sure PIN 1 is set to OFF.
3. When TP speed is set to 10M or 100M manually, PIN 3
needs to be turned OFF.
 4. Under 1000Mbps, it supports full-duplex mode only.
5. LED Description 7. Fiber Transceiver Information
LED Color Function 1000M
Power Green Lit when power is available. Multi-Mode/Single-Mode
Lit when TX cable connection with BTFC BTFC BTFC
TYPE BTFC
TX (SM-10) (SM-20) (SM-30)
Green remote device is good. Connector
Link/Act SC SC SC SC
Blink when TX traffic is present. Type
Lit when Fiber cable connection with Wavelength 850nm 1310nm 1310nm 1310nm
FO
Green remote device is good. Typical
Link/Act 550m 10 Km 20 Km 30 Km
Blink when F/O traffic is present. Distance
Lit when TX works in Full-Duplex. Min TX PWR -9.5dBm -9.5dBm -9.0dBm -5.0dBm
FDX Green
Not-Lit when TX works in Half-Duplex.
Green
No-Lit when TX works in 10M.
Max TX
PWR
-1.5dBm -3.0dBm -2.0dBm 3.0dBm CVT-3002-PLUS
Speed Lit when TX works in 100M. Sensitivity -17.0dBm -20.0dBm -23.0dBm -24.0dBm
Orange Lit when TX works in 1000M. Link Budget 7.5dB 10.5dB 14.0dB 19.0dB
SERIES
Green Lit when TX and F/O link is up.
Status
Orange Lit when TX or F/O link is down. 2 Wave-Length WDM
W2A W2B W2A W2B W2A W2B
TYPE
(SM-10) (SM-10) (SM-20) (SM-20) (SM-40) (SM-40) 10/100/1000Base-T to
6. Technical Specifications Connector
Type
SC SC SC SC SC SC
1000Base-X Standalone
Standards IEEE 802.3, 802.3u, 802.3ab, TX
802.3z, 802.3x
Wavelength
1310nm 1550nm 1310nm 1550nm 1310nm 1550nm
Media Converter
RX
Interface 1 X 10/100/1000 RJ-45 connector 1550nm 1310nm 1550nm 1310nm 1550nm 1310nm
Wavelength
1 X 1000 F/O port or SFP Slot Typical
10 Km 10 Km 20 Km 20 Km 40 Km 40 Km
LED Power, FDX, Status, Speed, Distance
FO Link/ACT, TX Link/ACT Min TX
-10.0dBm -10.0dBm -9.0dBm -9.0dBm -5.0dBm -5.0dBm
PWR
Power I/P AC 100-240V
Max TX
O/P DC 5V PWR
-3.0dBm -3.0dBm 0 dBm 0 dBm 3.0dBm 3.0dBm
Power Consumption 1.5W Sensitivity -22.0dBm -22.0dBm -23.0dBm -23.0dBm -23.0dBm -23.0dBm
Weight 0.2kg
Link Budget 12.0dB 12.0dB 14.0dB 14.0dB 18.0dB 18.0dB
Dimensions 71mm(W)X94mm(D)X26mm(H)
Temperature Operating: 0o~50oC NOTE: Specifications may be changed without prior notice.
Storage: -20o~60oC
Humidity 5%~90% RH non-condensing
Certification FCC/CE Class A
Media TP: EIA/TIA-568 CAT 5e,
1000M
Fiber: 50/125 or 62.5/125m
multi-mode
9/125 or 10/125m
single-mode
User’s Guide
* Please contact us for further reports and updates.
NOTE: Specifications may change without prior notice.
Contact Information Version 2.1
 Connection Technology Systems INC (CTS)
18F-6, No.79, Sec.1, Xintai 5th Rd., Xizhi Dist.,
New Taipei City 221, TAIWAN, R.O.C.
TEL: +886 2 26989661 FAX: +886 2 26989662
E-Mail: [email protected]