0% found this document useful (0 votes)

102 views96 pages

McKinney Full Line Catalog

Uploaded by

Joe Podurgiel

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

102 views96 pages

McKinney Full Line Catalog

Uploaded by

Joe Podurgiel

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

McKinney

Full Line Catalog

Table of Contents

Numerical Index 4
General Information 5-29
Warranty and Hinge Types 7-8
Bearings and Knuckle Features 9-10
Hinge Tips and Pins 11-12
Applications/Hinge Selection 13-17
Reference Charts 18-23
Hand of Doors and Hinges/Hinge Swaging 24-25
Screws and Fasteners 26-27
Finishes 28
Product Maintenance and Care 29
Full Mortise Hinges FM-1 - FM-17
Full Mortise Bearing Hinges - Two Knuckle Standard Weight Series FM-1
Full Mortise Bearing Hinges - Two Knuckle Heavy Weight Series FM-2
Full Mortise Bearing Hinges - Three Knuckle Standard Weight Series FM-3
Full Mortise Bearing Hinges - Three Knuckle Heavy Weight Series FM-4
Full Mortise Institutional Hinges - Three Knuckle Hospital Tip Heavy Weight Series FM-5
Swing Clear Full Mortise Bearing Hinges - Three Knuckle Heavy Weight Series (Reversible) FM-6
Full Mortise Plain Bearing Hinges - Five Knuckle Standard Weight Series FM-7
Hinge pin door stop FM-7, FM-16
Full Mortise Bearing Hinges - Five Knuckle Standard Weight Series FM-8
Full Mortise Concealed Bearing Hinges - Five Knuckle Standard Weight Series FM-9
Wide Throw Full Mortise Bearing Hinges - Five Knuckle Standard Weight Series FM-10
Full Mortise Bearing Hinges - Five Knuckle Heavy Weight Full Mortise Series FM-11
Full Mortise Concealed Bearing Hinges - Five Knuckle Heavy Weight Full Mortise Series FM-12
Wide Throw Full Mortise Bearing Hinges - Five Knuckle Heavy Weight Wide Throw Series FM-13
Swing Clear Full Mortise Bearing Hinges - Five Knuckle Standard Weight Swing Clear Series (Reversible) FM-14
Swing Clear Full Mortise Bearing Hinges - Five Knuckle Heavy Weight Swing Clear Series (Reversible) FM-15
Full Mortise Hinges - MacPro® Five Knuckle Standard Weight Series FM-16
Full Mortise Hinges - MacPro® Five Knuckle Heavy Weight Series FM-17
Full Mortise Anchor Hinges AH-1 - AH-4
Half Mortise Hinges HM-1 - HM-3
Half Mortise Bearing Hinges - Five Knuckle Standard Weight Half Mortise Series (Reversible) HM-1
Half Mortise Bearing Hinges - Five Knuckle Heavy Weight Half Mortise Series (Reversible) HM-2
Swing Clear Half Mortise Bearing Hinges - Five Knuckle Heavy Weight Half Mortise Swing Clear Series (Reversible) HM-3
Half Surface Hinges HS-1 - HS-4
Half Surface Plain Bearing Hinges - Five Knuckle Standard Weight Series (Reversible) HS-1
Half Surface Bearing Hinges - Five Knuckle Heavy Weight Series (Reversible) HS-2
Swing Clear Half Surface Bearing Hinges - Five Knuckle Heavy Weight Series (Reversible) HS-3
Hinge Back Plates HS-4
Full Surface Hinges FS-1 - FS-2
Full Surface Bearing Hinges - Five Knuckle Heavy Weight Series (Reversible) FS-1
Full Surface Bearing Hinges - Five Knuckle Standard Weight Series (Reversible) FS-2
Spring Hinges & Pivots SH-1 - SH-12
Full Mortise Single Acting Standard Weight Spring Hinge SH-1
MacPro® Adjustable Spring Hinge SH-2
Full Surface Double Acting Door Spring SH-3

800-346-7707 | [Link]
Check the web site for the up-to-date catalog
McKinney is a brand associated with Corbin Russwin, Inc., an ASSA ABLOY Group company. Copyright © 2012-2017, Corbin Russwin, Inc.
2 All rights reserved. Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited.
Table of Contents
Rescue Hardware RH-1 - RH-4
Jamb Mount Pivot Set RH-1
Combination Strike and Stop RH-2
Emergency Door Stop RH-3
Double Lipped Strike RH-4
Electrified Hinges EH-1 - EH-12
Electrolynx® Hinge (QC Option) EH-1
ElectroLynx® Retrofit Cables EH-2
MacPro® Electric Hinges EH-3
Concealed Circuit Electric Hinge (CC option) EH-4
ElectroLynx® Power over Ethernet (PoE) Hinge and Wiring Harnesses EH-5 - EH-6
Magnetic Monitoring Hinge (MM Option) EH-7
Electrical Power Transfer (EPT) EH-8
Electrified Hinge Service Kit EH-9
Extraction Tool/Junction Box for Electric Hinges EH-10
Specialty Hinges SP-1 - SP-6
StormPro® Tornado Resistant Hinges SP-1
Pocket Pivot Hinges SP-2
Raised Barrel Full Mortise Standard and Heavy Weight Hinges SP-3
Slip-In Full Mortise Type I and Type II Standard Weight Bearing Hinges SP-4
Full Mortise Interim Hinges SP-5
Residential Hinges SP-6
Swing Clear Hinges SP-6
RediFrame Swing Clear Hinge SP-6
Residential Spring Hinges SP-7
Residential Hinges SP-7
Decorative Hinges - Square Barrel SP-8
Decorative Hinges - Olive Knuckel SP-9
Concealed Hinges SP-10 - SP-11
Cam Lift Hinges SP-12

Numerical Index
451, 452, 453 SH-3 TA386 FM-4
1400, 1414, 1458 SP-7 TA391 AH-1
1502, 1552 SH-1, SP7 TA392 AH-2
BP-10, BP-11, BP-12 HS-4 TA393 AH-3
CC Option EH-4 TA394 AH-4
CSS-9 RH-1 TA714 FM-3
DLS-8 RH-4 TA786 FM-4
DS-6 RH-3 TA791 AH-1
EP-5J RH-1 TA792 AH-2
Hinge Pin Door Stop FM-7, FM-16 TA794 AH-4
HTA386 FM-5 TA795 FM-6
HTA786 FM-5 TA2314 FM-8
Interim Hinge SP-5 TA2371 FS-2
MG-16 EH-10 TA2372 HS-1
MK40A SP-10 TA2395 FM-14
MK80, MK80A, MK80SS SP-10 TA2398 FM-10
MK100 SP-10 TA2714 FM-8
MK150 SP-10 TA2731 FM-1
MK200 SP-10 TA2771 FS-2
MKCL134 SP-12 TA2772 HS-2
MKCL180 SP-12 TA2774 HM-1
MKCL250 SP-12 TA2798 FM-10
MKCL2500 SP-12 TA2895 FM-14
MM Option EH-7 TA3331 FM-1
MP79, MPB79, MPB91 FM-16 TA3350 FM-2
MP79 QC or CC Option EH-3 TA3383 SP-9
MPB68, MPB99 FM-17 TA3374 HM-1
MPB68 QC or CC Option EH-3 TA3750 FM-2
MPS60, MPS679 SH-2 TA4895 FM-14, SP-6
PH-4 SP-2 TCA2314 FM-9
PoE Option EH-5, EH-6 TCA2714 FM-9
QC Option EH-1, EH-2 TCA3386 FM-12
QC-R001 EH-9 T4A3386 Wide Throw FM-13
QC-R002 EH-10 TCA3786 FM-12
QC-R003 EH-9 T4A3381 FS-1
RB-TA2314, RB-TA2714 SP-3 T4A3382 HS-2
RB-T4A3386, RB-T4A3786 SP-3 T4A3384 HM-2
RediFrame Swing Clear Hinge SP-6 T4A3386 FM-11
Residential Hinges SP-6,SP-7 T4A3395 FM-15
Slip-In Hinge SP-4 T4A3781 FS-1
SP3386 SP-1 T4A3782 HS-2
SP3786 SP-1 T4A3784 HM-2
SQ3331 SP-8 T4A3786 FM-11
SQ314 SP-8 T4A3786 Wide Throw FM-13
Swing Clear Hinges T2895 SP-6 T4A3789 HM-3
T2314, T2714 FM-7 T4A3795 FM-15
TA314 FM-3 T4A3796 HS-3

Custom Manufacturing
A variety of materials and hinge types can be custom manufactured in the
Berlin, CT plant, including the ElectroLynx® hinges and Power over Ethernet
hinges. For more information on custom manufactured hinges, call McKinney
.

Innovation
To support today’s need for electronic security applications, we have
developed a variety of electric hinges used in remote door monitoring and
access control systems, and received a patent on the Power over Ethernet
(PoE) hinge. In addition, by combining McKinney hinges with other ASSA ABLOY
Group products, we can offer StormPro tornado resistant solutions.

Decorative Hinges
The McKinney line of decorative architectural hinges comes with special
tips and finishes. Designed to suite with hardware from ASSA ABLOY Group
brands, these commercial decorative hinges open up a whole new world of
design options for your door openings. See the McKinney Architectural Hinge
Brochure for the complete offering.

The Good Design Studio - your resource for beautiful doors, frames and hardware from
ASSA ABLOY Group brands. Visit [Link] to learn more.

McKinney PoE Hinge,

U.S. Patent No. 7,824,200
Corbin Russwin 107 McKinney 2 knuckle hinge Rockwood
and SARGENT ME lever with round end tips small door pull

LEED Certification Contribution

ASSA ABLOY can help to achieve prerequisites and accumulate points in several
categories and credit areas of LEED. For further information, please call
1 800 346 7707 or refer to our website [Link].

ASSA ABLOY is a member of the USGBC and CaGBC U.S.

Green Building Council logo is a trademark owned by
the U.S. Green Building Council and is used with permission.

Sales & Support

The McKinney product line is represented by the
ASSA ABLOY Door Security Solutions team.
Phone: 1 800 DSS EZ4U (800 377 3948)
Address: 110 Sargent Drive, New Haven, CT 06511
Web site: [Link]
Email: Contact your local ASSA ABLOY Door Security Solutions
Representative via e-mail by going to [Link]
and clicking on “Sales Support”.
Customer Service and Tech Support Representatives are available
during regular business hours at 1 800 346 7707 or email
[Link]@[Link] or
[Link]@[Link].
Visit the Architectural Door Accessories website for the most up-to-date
catalogs, promo sheets and templates : [Link]
Order online from the Architectural Door Accessories WebShop:
[Link]
For WebShop assistance call 203 821 5763.
Many popular McKinney products are stocked and ready to ship from
warehouses in Ventura CA and Berlin CT. In addition, over 400 stock items are
included in a 3-day QuickShip Program from the Berlin, CT plant. Details on the
QuickShip program are available on the website.

Terms & Conditions

Complete shipment of the order must be accepted by Purchaser within normal lead times. The QUOTE number must be referenced
on the order. The QUOTE is null and void if the Purchase Order does not include ALL product lines listed on the
QUOTE or if the quantities for an item covered by the QUOTE deviate by 10% or more.
Terms are 1% 15 Net 30. A charge of $50.00 will be made for itemization. A charge of $25.00 will be made when changes are
requested on itemized jobs already processed. No invoice will be rendered for less than $50.00 net. On non-standard items
a 5% over or under run constitutes a complete order.

Terms
It is understood that a finance charge may be imposed which is the lesser or one and one-half percent (1 1⁄2) per month of
the highest rate allowed by law on any amount which becomes past due and delinquent. Additionally the Customer shall be
responsible for all collection costs, court costs and reasonable attorney’s fees (where allowed by law) in connection with the
recovery of any delinquent amount.

Credit
Acceptance of orders and deliveries thereof shall at all times be subject to our approval of credit.

Shipments
Once in the hands of the transportation company, the Purchaser assumes the risk of loss or damage in transit.
All goods are F.O.B. shipping point via the most economical routing, with carrier chosen by us. Full freight prepaid on shipments
within Continental United States having a net value of $1,750 or more.

Returned Goods
No credit will be issued for returned goods unless such return is authorized. If such authorization is given by us, there will be a
minimum handling charge of 45% or $50.00 which ever is greater, for stock items shipped within a 90 day period from the date
of the request.

Cancellations
We are unable to accept cancellations or changes on non-stock and special ordered (s/o) items once processing begins.
A charge will be assessed based on manufacturing expense incurred.

800-346-7707 | [Link]
Check the web site for the up-to-date catalog
McKinney is a brand associated with Corbin Russwin, Inc., an ASSA ABLOY Group company. Copyright © 2012-2017, Corbin Russwin, Inc.
6 All rights reserved. Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited.
Warranty And Hinge Types
Product Warranty
Our products are guaranteed to be free of defects in both workmanship and materials for a period of one year. Any bending,
defacing or modification of our product after leaving the factory will void the warranty. Liability shall be limited to the replacement
of product or component determined to be defective and shall not include costs arising from removal or reinstallation of product.
Cost of replacement shall not exceed original purchase price.
Written notice of damages must occur within the warranty period. A factory generated Return Goods Authorization will be
provided as no goods will be accepted without prior approval. These defective goods must be returned to our factory in Berlin,
CT, unless specified otherwise. Freight charges must be pre-paid unless noted otherwise.
This guarantee is only valid if the products are specified, applied and adjusted in accordance with the instructions contained in
the General Information Section of the McKinney product catalog and on frames and doors that are plumb and square.

Bulk Packed Hinges

We offer bulk packaging on most popular hinges. Hinges arrive ready-to-install with no interior packaging and screws in
bulk, which reduces the amount of material to discard. This also saves time, especially on larger installations, as individual boxes
do not need to be opened. The packaging is reinforced and holds 48 hinges. In addition, the box is strapped to ensure it arrives
intact at its destination.
The program is offered on the hinges listed below in 26D, with other finishes available upon request.
Orders are shipped quickly in 3 days or less.

Bulk Pack
No. Size Finish Material Weight
Quantity
T2714 4-1/2" x 4-1/2" 26D Steel STD 48

TA2714 4-1/2" x 4-1/2" 26D Steel STD 48

TA2714 NRP 4-1/2" x 4-1/2" 26D Steel STD 48

MacPro®:
MP79 4-1/2" x 4-1/2" 26D Steel STD 48

MPB79 4-1/2" x 4-1/2" 26D Steel STD 48

MPB79 NRP 4-1/2" x 4-1/2" 26D Steel STD 48

TO ORDER: Add the suffix BP to the part number, for example TA2714 BP 4-1/2 x 4-1/2 26D

Hinge Types
Our broad range of full mortise hinges come in a variety of metals, finishes, sizes, and weights to meet all your load bearing and
security applications. They include two, three, and five knuckle styles, swing clear hinges, wide throw hinges, anchor hinges,
electric hinges, institutional hinges, and pivots.
ASSA ABLOY hinges conform to Government standards CS9-65 and SDI as well as the following standards approved by the
Builders hardware Manufacturers/American National Standards Institute:

ANSI/BHMA Standard 156.1 - ANSI/BHMA Standard 156.17 -

The American National Standard for Butts and Hinges The American National Standard for Self-Closing
Hinges & Pivots
ANSI/BHMA Standard 156.7 -
The American National Standard for Template Hinge ANSI/BHMA Standard 1156.18 -
Dimensions The American National Standard for Material and Finishes

Full Mortise Hinges Full Surface Hinges

Our broad range of full mortise hinges come in a variety of Choose from regular and swing clear models for heavy weight
metals, finishes, sizes, and weights to meet all your load bearing or standard weight bearing applications in a choice of
bearing and security applications. They include two, three, metals, gauges, and sizes. Two knuckle, three knuckle, and five
and five knuckle styles, swing clear hinges, wide throw hinges, knuckle styles are available.
anchor hinges, electric hinges, institutional hinges,
and pivots.

Half Mortise Hinges Half Surface Hinges

Available in a choice of metals, gauges, and sizes for a wide Heavy weight bearing, standard weight bearing, and plain
range of door thicknesses. You may specify plain bearing, bearing hinges in a range of metals, gauges, and sizes.
standard weight bearing, or heavy weight bearing models. Regular and swing clear applications. Three knuckle, and
Regular and swing clear applications. Three knuckle, as well five knuckle styles.
as five knuckle styles are available.

Security Hinges Spring & Specialty Hinges

Our assortment of electrical security hinges are suitable for A full range of spring hinges are available for all types of door
a wide variety of control functions. Included are full mortise sizes, weights, and applications. Included are full mortise
bearing hinges with either concealed circuitry or concealed single acting hinges, full mortise double acting hinges, and
switch. In addition, a unique, field-replaceable magnet half surface double acting hinges, plus our heavy duty spring
monitoring hinge, featuring a magnetic reed concealed switch, butt hinge that permits doors to open 90˚ in either direction.
is available. We also produce full mortise institutional hinges for In addition, we produce a variety of hinges for special
maximum security installations. applications including anchor hinges, wide throw hinges, swing
clear hinges, and pocket hinges.

Electric Hinges Miscellaneous

To meet today’s need for greater security applications, ASSA ABLOY provides a standard duty center hung jamb
ASSA ABLOY developed a variety of electric hinges used in mount pivot set as well as emergency door stops and strikes.
remote door monitoring and access control systems. These
The most up to date templates are available on the
ElectroLynx® Hinges use convenient Molex connectors to make
website at [Link].
installation quick and simple.
Traditional wired connection electric hinges are available with
28 gauge and 18 gauge wires.

Oil Impregnated Bearing (TA)

One piece, non-ferrous, and self-lubricating bearings ensure
even longer-lasting wear and resistance to clogging, corrosion,
and hinge failure. This feature is standard and supplied on all
five knuckle bearing hinges up to 5" height. All 6" or larger are
Ball Bearing hinges.

Ball Bearing (TB)

Ball bearings are available as an option on all five knuckle
bearing hinges up to 5". All 6" hinges or larger are ball bearing
as a standard.

Concealed Bearing (TCA)

Concealed, anti-friction type bearings are available on all five
knuckle bearing hinges, which provide long-lasting wear and
consistency of hinge barrel design.
Note: All three and two knuckle bearing hinges are provided with
concealed, anti-friction type bearings (designated TA).

Plain Bearing
This is the designation for non-bearing hinges. Knuckles are
machined with bearing-like surfaces to move against one
another. These are not recommended for high frequency doors
or doors with closing devices. These hinges are not approved
for use in labeled openings.

Hinge Knuckles
Our line includes two, three and five knuckle hinges.

Modern Two Knuckle

This model offers the most security in a standard hinge. By design, pins are non-rising, non-removable and tamper
The bearing hinges have a concealed stainless steel protected by a flush, non-removable cap at the end of the
oil-impregnated bearing. Also, an anti-friction bushing in barrel. A door can not be removed when in the closed position,
the door leaf provides additional protection against vertical thus affording maximum security. Intermediate hinges can be
and lateral wear. ordered opposite hand and installed upside down, to inhibit
removal of the door in an open position
•T
he Moderne two knuckle hinge is available in
stainless steel •A
vailable non-removable door (NRD) hinges have a dowel
in the barrel. One NRD hinge can be ordered per set
• Standard and heavy weight
• Two knuckle hinges are handed
• Pins in all bearing hinges are stainless steel
•T
emplate hinges are made to conform to U.S.
•S
tandard hinges are packed with all machine and all
Government standards*
wood screws

Three Knuckle Five Knuckle

Bearing hinges have concealed vertical and lateral thrust twin Bearing hinges are furnished with either an oil-impregnated
anti-friction type bearings at both joints. bearing (TA)** or ball bearing (TB). (TA is standard unless
TB is specified.) Concealed bearings (TCA) are available.
•P
ins in all non-ferrous bearing hinges are
stainless steel •P
in stems in all non-ferrous bearing hinges are
stainless steel
• Pins in all ferrous hinges are steel
• Pins in all ferrous hinges are steel
• Pins in all hinges are non-rising type
• Pins in all hinges are non-rising type
•S
tandard hinges are packed with all machine and all
wood screws •T
emplate hinges are made to conform to U.S. Government
standards*
•H
inges are reversible for right or left hand except anchor
hinges and certain electric hinges **Refer to our website at [Link] for additional
information regarding ASSA ABLOY bearings.
•T
emplate hinges are made to conform to U.S.
Government standards*

*Template hinges are made in sizes, gauges, and with screw holes located to conform to ANSI/BHMA A156.7 and U.S. Government standards CS9-65 and
SDI. Templates are available on request.

PSF - Prison Safety Feature SSF - Safety Stud Feature

A 7/16" diameter stud projects from the A stud attached to the face of one leaf
back of each leaf which slips into a hole rotates into a cavity in the opposite leaf
in the hinge reinforcing plates in both when the door is closed. This option
the door and the frame. This prevents interlocks the two leaves together,
the hinge from being removed even if preventing the removal of the door even
the screws have been sheared off. This if the pin is removed.
option is available on the HTA786 steel
and HTA386 stainless prison hinge only.

Button Tips (Standard)

Button Tips and plugs are standard on five knuckle hinges.

Flush Pins (Standard)

Flush pins and plugs are furnished on our two and three knuckle hinges.

Hospital Tips
Hospital tips which feature a one-piece non-removable pin with tapered
tips. To order this option prefix our hinge number by “HT”. The hospital
tip feature by design makes the pin virtually non-removable.

Decorative Tips
Decorative tips enhance the design of your interior. Available for the
two or three knuckle hinge in flat, round, grooved or lined tip styles.
FT RT
These hinges are designed to suite with doors and hardware from
the ASSA ABLOY Group brands.

GT LT

Ball Tips
Ball Tips, made of solid brass, are available on five knuckle hinges
for a more decorative hinge appearance. To order this option add
the suffix “BT” to the hinge number.

Steeple Tips
Steeple Tips, made of solid brass, are available on five knuckle
hinges for a more decorative hinge appearance. To order this hinge
option, add the suffix “ST” to the hinge number.

Hinge Pins
Pins, by design, are non-rising.

Two Knuckle
Pins on bearing hinges are furnished in stainless steel.

Three Knuckle
Pin stems in all non-ferrous bearing hinges are stainless steel.
Pins in all ferrous hinges are steel.

Five Knuckle
Pins on all non-ferrous bearing hinges are stainless steel
with button tips.
Pins on all ferrous hinges are steel.

Non-Removable Pins

NRP NRD
A set screw is driven into the barrel of the hinge that is Two knuckle hinges are available with a non-removable pin
inaccessible when the door is in the closed position. To order, which features a dowel which is force fitted into the jamb
add the suffix “NRP” to the hinge number. leaf. When the door is hung, the pin is completely concealed
and impossible to remove. One doweled hinge is usually
furnished per set of three. To order, add the suffix “NRD” to
the hinge number.

32 " or /8 " may be specified on full mortise hinges.

5/ 5

Specify option “RC”.

Applications
This section will seek to address different variations be on the type of hinge to use within a given door/frame/wall
of door, frame and wall conditions which you might condition. The following examples are not intended to cover
encounter in hanging the door and the product solutions every possible situation in which a particular type hinge might
offered in the McKinney line. be used, but only a representative sampling. Consult the factory
for any unusual installation requirements not shown here.
Included are some of the more common conditions and
some of the not-so-common conditions. The focus here will

Common Applications
Full Mortise Hinge TA2714
Application
The most common application is a flush door/frame/wall
condition using a hollow metal frame with a standard hollow
metal or wood door which is flush or 1/16" inset from the face
of the frame, with a wall which is either flush (or inset from
the face of the frame. Recommended to hang door for 180˚
swing: Full Mortise Hinge. The same hinge could be used
with a wood or aluminum frame provided the door/frame/
wall conditions are flush.
Note: A fire labeled wood door requires sufficient hinge reinforcement
to use this type hinge.

Less Common flush door/frame/wall application

Half Mortise Hinge TA2774
Application
A hollow metal or wood door with channel iron frame.
Recommended to hang door for 180˚ swing:
Half Mortise Hinge.

Less Common flush door/frame/wall application

TA2771 Full Surface Hinge
Application
A fire labeled wood door (without sufficient hinge
reinforcement) or a kalamein (metal-clad wood door) with
channel iron frame. Recommended to hang door for 80˚
swing: Full Surface Hinge. On fire labeled wood doors, the
door leaf is hung using a back plate with grommet nuts and
bolts. Another popular application for this type hinge is a
tubular steel gate hung on a channel iron frame.

TA2772 Half Surface Hinge

Application
A fire labeled wood door (without sufficient hinge
reinforcement) or a kalamein (metal-clad wood door) with
channel iron frame. Recommended to hang door for 180˚
swing: Half Surface Hinge. On fire labeled wood doors, the
door leaf is hung using a back plate with grommet nuts
and bolts.

Special Applications
TA792 Anchor Hinge
Application
On high frequency and/or heavy wood or metal doors,
additional anchoring of the hinges into the door and jamb
may be necessary. This is a common application in schools,
hospitals or any other buildings where heavy traffic and
unusual strain on the doors, jamb and hinges is experienced.
Recommended to hang door for 80˚ swing: Full Mortise
Anchor Hinge. Sold in sets of one full mortise anchor hinge
and two heavy weight full mortise hinges.
Note: Anchor hinges are handed and sold for either square edge doors on
hinge side or beveled (1/8" in 2") edge doors on hinge side. Hand and bevel
(McKinney hinges use uses a "5" in front of the item number to indicate 1/8"
in 2" bevel. Example: TA5792 should be specified.

800-346-7707 | [Link]
Check the web site for the up-to-date catalog
McKinney is a brand associated with Corbin Russwin, Inc., an ASSA ABLOY Group company. Copyright © 2012-2017, Corbin Russwin, Inc.
14 All rights reserved. Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited.
Applications
Special Applications
Spring Hinge 1502
Some door/frame/wall and even ceiling conditions make door (Full Mortise Type)
closers impractical. An alternative closing device is the Spring
Hinge. Generally, at least two hinges on a door must be spring
hinges to provide adequate closing force.
Note: NFPA requires a minimum of two (2) spring hinges on fire labeled
doors. With adjustable spring tension on the hinge, the closing speed of the
door is determined by the amount of closing force set on the hinge. Spring
hinges may not be suitable for applications requiring a closing device with
non-critical closing and latching speed adjustments. With respect to meeting
ADA requirements for closing devices, carpeting and/or gasketing can
interfere with latching.

Swing Clear Hinge TA2895

Application
A condition which is common in barrier free openings, and
especially in hospitals, is how to remove the door edge
from the opening at 90˚ of swing with flush door/wall/ frame
conditions. The solution offered by this hinge is the offset of
the hinge barrel to a location along the face of the hinge jamb,
thereby removing the door edge and the barrel of the hinge as
obstacles in the opening at 90˚ or more of swing. If the door
is beveled on the hinge side, specify the appropriate beveled
hinge and handing for your application*.
*Consult individual Swing Clear catalog pages for beveled hinge
product numbers.
Electric versions available- QC, CC, CC-18

Meets or exceeds
ANSI A117.1 - 1986
Providing Accessibility
and Usability for Physically
Handicapped People

Non-Flush Door/Wall/Frame Applications

TA2798 Wide Throw Hinge
Application
If the door is not flush with the frame, is sitting back in a deep
reveal from the face of the frame with or without additional
obstacles created by applied trim on the face of the frame or a
deeper reveal caused by a projecting wall, and the door is to
swing 180˚, then a Full Mortise Wide Throw Hinge may be
used in hanging the door.
Important in this regard is how to calculate the proper width of
a wide throw hinge (rounded to the next higher whole number if
result is not a whole number: e.g., 6", 7", 8", etc.)

How To Calculate The Proper Wide Throw Hinge Width

1. If the door is sitting inside a deep frame reveal with no other obstacles (i.e., projecting
trim or wall), add the depth of the reveal (distance from the face of the frame to the
face of the door) to the recommended width of hinge used under flush conditions.
Example: A 6" wide (wide throw) hinge would replace a 41/2" wide regular mortise
hinge (used under flush conditions) if the depth of the reveal is 11/2".

2. If the door is to clear projecting trim or wall and the barrel of the hinge is not obstructed, then
calculate as follows:
(a) double the size of the door
(b) subtract 1/2" if the door thickness is less than or equal to 21/4" or subtract 3/4" if the door
thickness is greater than 21/4"
(c) add for the additional depth from the face of the obstruction to the face of the door
(d) a
dd for clearance between the door and the face of the obstruction at 180˚ of swing
(generally 1" or more).

If, for instance, you have a 13/4" thick door:

(a) 13/4" door thickness x 2 = 31/2"
(b) less 1/
2 " equals 3"
(c) p
lus 3" for the additional depth from the face
of the wall to the face of the door equals 6"
(d) p
lus 1" for the clearance between the door
and the face of the obstruction at 180˚ of
swing equals 7" overall hinge width.

Pocket Hinge
An increasingly popular door, frame and wall condition in
PH-4 Application

corridors is cross-corridor or double egress pairs of doors

standing in wall pockets at 90˚ of swing, so as to be clear of
the initial opening and out of the corridor altogether.
Solution: Pocket Hinge.
As corridor doors are often fire labeled, the hardware must
be approved for use in fire labeled openings. Solution: the
McKinney PH-4 Pocket Hinge. UL approved for use on both
hollow metal and steel covered composite fire doors rated up to
3 hours and on wood core type fire doors rated 20 minutes.

Pivots
Recommended for use on average frequency double acting
EP-5J
doors in schools, hospitals, institutions and other public
buildings. Not for use on labeled doors and frames.

Quick Reference Chart

Variation of McKinney
Door, Frame Wall Basic Hinge Type Brand
Frame Type Door Type Hinge Type
Conditions Shown Below Example
(See Note 2) (See Note 3)

Wood
Flush* Wood or Metal Full Mortise (not applicable) TA2714
or Metal

Flush* Channel Iron Wood or Metal Half Mortise (not applicable) TA2774

Kalamein or Fire
Flush* Channel Iron Labeled Wood Full Surface (not applicable) TA2771
Door (See Note 1)

Kalamein or Fire
Flush* Metal Labeled Wood Half Surface (not applicable) TA2772
Door (See Note 1)

Heavy and/or High

Flush* Metal Frequency Wood Anchor Full Mortise TA792
or Metal

Wood or Metal
Wood Full Mortise
Flush* Requiring Alternative Closing Spring 1502
or Metal Half Surface
Device

Wood or Metal
Wood
Flush* Required to Clear Swing Clear Full Mortise TA2895
or Metal
Opening at 90˚ of Swing

Wood or Metal with

Wood
Deep Frame Reveal Maximum Swing of 90˚ Raised Barrel Full Mortise RBTA2714
or Metal
to 110˚

Deep Frame Reveal

with or without
Wood Wood or Metal with
Trim on the Face of Wide Throw Full Mortise TA2798
or Metal swing to 180˚
the Frame or a Projecting
Wall

Wall Pocket at
Metal Wood or Metal Pocket Hinge (not applicable) PH-4
90˚ of swing

* Includes door and frame conditions of up to 1/8" inset

Notes:
1. Fire labeled wood door without sufficient hinge reinforcement. Door leaf is hung using back plate with grommet nuts and bolts.
2. The four basic hinge types are full mortise, half mortise, full surface and half surface. Variations (i.e. anchor, swing clear, raised barrel,
wide throw) are available in the basic types shown above but may not be available in all basic hinge types. Consult individual catalog
pages for availability.
3. Consult individual catalog pages for available sizes, weights, materials, versions, bearings and finishes. Hinges for doors beveled
(1/8" in 2") on hinge side use 5000 series for 3K hinges (e.g. TA5792); use 4000 series for 5K hinges (e.g., TA4895).

Door Weights* (Based upon 3' 0" x 7' 0" Door Size)

Hollow Metal Door Weights by Gauge Wood Door Weights by Door Thickness
Door Gauge — # Per Square Foot # Per Square Foot
20 Gauge Door 4 Door Thickness 13/8" 13/4"
18 Gauge Door 5 Particle/Mineral Core 4.75 5.25
16 Gauge Door 6 Stave Core Wood 3.75 4.25
14 Gauge Door 7 Hollow Core Wood 1.3 1.5
* Weights do not include hardware.

How to Determine the Proper Hinge Width

Knowing the door thickness and trim projection, use the following formula for determining minimum hinge
width for all full mortise hinges:
1. Door thickness
2. Backset
3. Required Clearance
4. Inset
Door thickness - Backset x 2 + Required Clearance + Inset (if applicable) = the proper hinge width

D = Door Thickness
B = Backset
W = Hinge Width
D = Door Thickness
T = Trim Depth
W = Hinge Width "B"

"D"

Clearance
"W"

For doors up to 21/2" thick:

W=(2 x D) + T
For doors 21/2" to 3" thick:
W=(2 x D)+(2 x T)+ 1/4"

The table below indicates the trim clearance provided by hinges of specified widths on flush doors, not inset, of standard
thickness. For doors of other thicknesses, apply the proper formula.

Trim Clearance

Door Thickness Hinge Width Max Clearance Provided

1 8"
3/
3 2"
1/
11/4"
4" 13/4"
13/4" 4" 1"
41/2" 11/2"
5" 2"
6" 3"
2" 41/2" 1"
5" 2"
1/

6" 21/2"
21/4" 5" 1"
6" 2"

The hinge widths of half mortise, half surface and full surface hinges are standard, depending on the hinge length. Note that in
these hinge types, the amount of clearance available is determined by the amount of offset and not by the hinge width.

Recommended Size of Hinges per Door (Wood or Metal)

Door Thickness Door Width Hinge Height

Hinge Gauge
in Inches (mm) in Inches (mm) in Inches (mm)

13/8" (35) Up to 36" (914) 31/2" (89) .123

13/8" (35) Over 36" (914) 4" (102) .130
1 4" (44)
3/
Up to 36" (914) 4 2" (114)
1/
.134
1 4" (44)
3/
36" – 48" 5" (127) .134
(914 – 1219)
13/4" (44) Over 48" (1219) 6" (152) .160
2" – 2 2" (51 – 64)
1/
Up to 42" (1067) 5" (127) HW* .190
2" – 21/2" (51 – 64) Over 42" (1067) 6" (152) HW* .203

* Heavy Weight hinges should be used on all extra heavy doors or those exposed to high frequency use.
Consult the factory for doors wider than 3'0". Five knuckle heavy weight hinges are four bearing.
The following gauges of metal may apply:
Heavy weight 41/2" (114) high = .180 gauge
Heavy weight 5" (127) high = .190 gauge
Heavy weight 6" (152) high = .203 gauge

Note: Five knuckle 8" (203) high hinges have six bearings.
Note: On hinge size the dimension shown is the hinge height. Where full mortise or other hinges with two
dimensions are used, the first dimension given is always the height. The second dimension is the hinge width
when open.

Expected Frequency*
Installation Type Daily Yearly
Commercial
Commercial Store Entrance 5,000 1,500,000
Office Building Entrance 4,000 1,200,000
Theater Entrance 1,000 450,000

High
School Entrance 1,250 225,000
School Restroom Door 1,250 225,000
Store or Bank Entrance 500 150,000
Office Building Restroom Door 400 118,000
School Corridor Door 80 15,000

Average
Office Building Corridor Door 75 22,000
Store Restroom Door 60 18,000

Residential
Entrance 40 15,000
Restroom Door 25 9,000

Low
Corridor Door 10 3,600
Closet Door 6 2,200

* One cycle = one complete opening and closing.

Note: We recommend that bearing hinges be used on all above categories other than “Residential”.

Recommended Number of Hinges per Door 3'0" Wide (Wood or Metal)

Door Height in Inches (mm) # of Hinges Per Door

Up to 60 (1524) 2
60 – 90 (1524 – 2286) 3
90 – 120 (2286 – 3048) 4

Note: An additional hinge is required for each additional 30".

Underwriters' Laboratories Requirements

The requirements of the Underwriters’ Laboratories, Inc., for fire
door hardware are determined by door label, which in turn is
established by the location of the opening. The following are
the classifications of Underwriter’s Laboratories, Inc.

Door Situation Location

Class A Fire Walls
Class B Vertical Shafts
Class C Corridor & Room Partitions
Class D Exterior Walls
(severe fire exposure)
Class D Exterior Fire Escapes
(severe fire exposure)
Class E Exterior Wall
(moderate fire exposure)
Class E Exterior Fire Escapes
(moderate fire exposure)

On all public and some private heavy construction three hinges Three hinges assure proper door alignment and enable other
are required for each door. This practice is standard under U.S. hardware to function properly. There is less door warping and
Government specifications and is required under most building less hinge wear. On light wood doors the alignment problem is
codes and Fire Underwriters’ specifications. as great as on heavy doors so less than three hinges should
never be considered.

The top of the top hinge should be 5" from the jamb header. EXCEPTION:
The bottom of the bottom hinge should be 10" from the The McKinney Anchor Hinge mounts at the very top of the door.
finished floor. On doors over 7'6" high, four hinges are required.
The center of the center hinge should be equidistant
from the other two hinges.

Maximum Door Size Minimum Hinge Size

Maximum
Width Height Height Thickness
Door Rating Type Hinge
ft. (m) ft. (m) in. (mm) in. (mm)
Hours
For 13/4" (44.5mm) or Thicker Doors
3 or less 4 (1.22) 10 (3.05) 41/2" (114.3) 0.180 (4.57) Steel, Mortise or Surface

3 or less 4 (1.22) 8 (2.44) 4 2" (114.3)

1/
0.134 (3.40) Steel, Mortise or Surface

11/
2 or less 31/
6 (0.96) 8 (2.44) 6" (152.4) 0.225 (5.72) Steel-Olive Knuckle or Paumelle

3 or less 4 (1.22) 10 (3.05) 4" (101.6) 0.225 (5.72) Steel Pivots (including top, bottom and intermediate)

11/
2 or less 3 (0.91) 5 (1.52) 4" (101.6) 0.130 (3.30) Steel, Mortise or Surface

11/2 or less 2 (0.61) 3 (0.91) 3" (76.2) 0.092 (2.34) Steel, Mortise or Surface

3 or less 3 (0.91) 7 (2.13) 41/2" (114.3) 0.134 (3.40) Steel, Mortise or Surface (labeled self closing spring type)

3 or less 3 (0.91) 7 (2.13) 4" (101.6) 0.105 (2.67) Steel, Mortise or Surface (labeled self closing spring type)

For 13/8" (34.93mm) Doors

3 or less 3 (0.91) 7 (2.13) 31/2" (88.9) 0.123 (3.12) Steel, Mortise or Surface

3 or less 2 2/
3 (0.81) 7 (2.13) 3 2" (88.9)
1/
0.105 (2.67) Steel, Mortise, or Surface (labeled, self-closing, spring type)

Note: Table [Link] lists the most common applications of hinges, spring hinges and pivots. Consult the door and hardware manufacturer's specific listings for
applications not addressed in this table.

6.4.3* Builders Hardware.

[Link] Hinges and pivots. Hinges, spring hinges, continuous hinges, and pivots shall be as specified in individual door and hardware
manufacturer's published listings or Table [Link].
[Link].1* Doors up to 60 in. (1.52 m) in height shall be provided with at least two hinges.
[Link].2 Doors in excess of 60 in. (1.52 m) shall have an additional 30 in. (0.76 m) of door height or fraction thereof, or in accordance
with the manufacturer's published listing.
[Link].3 The distance between hinges shall be permitted to exceed 30 in. (0.76 m).
[Link].4 Where spring hinges are used, at least two shall be provided.
[Link].5 All hinges or pivots, except spring hinges, shall be of the ball bearing type.
[Link].5.1 Hinges or pivots employing other antifriction bearing surfaces shall be permitted if they meet the requirements of ANSI/BHMA
A156.1, Standard for Butts and Hinges.
[Link].5.2 Spring hinges shall be labeled and shall meet the requirements of ANSI/BHMA A156.17, Standard for Self Closing Hinges &
Pivots, Grade 1.
[Link].6 Hinges 4-1/2 in. (114 mm high and 0.180 in. (4.57 mm) thick) shall be permitted for use on wide and heavy doors or doors that
are subjected to heavy use or unusual stress.
[Link].7 Fire doors with hinges of lighter weight that are not of the ball bearing type shall be permitted under the following conditions:
(1) They are part of a listed assembly.
(2) They meet the test requirements of ANSI/BHMA A156.1, Standard for Butts and Hinges.
(3) They have been tested to a minimum of 350,000 cycles.

Reproduced with permission of NFPA from NFPA 80, Standard for Fire Doors and Other Opening Protectives, 2022 edition.
Copyright© 2021, National Fire Protection Association. For a full copy of NFPA 80, please go to [Link].

Hand of Doors
All doors are handed - right or left. The following Regular Doors Opening In
illustrations indicate clearly this “handing” as it is
understood within the hardware industry.
Hand of door is determined from the outside.
When standing on outside of door and hinges are on the
right, it is right hand. When hinges are on the left, it is
left hand.
OUTSIDE OUTSIDE
A double acting door opens from you and toward you, Left Hand Door takes left hand hinges Right Hand Door takes right hand hinges

therefore it is not called reverse like a single acting door.

Reverse Doors Opening Out

OUTSIDE OUTSIDE
Left Hand Reverse Door takes right hand hinges Right Hand Reverse Door takes left hand hinges

Double Acting Doors

Right Side of Hinge Left Side of Hinge

Left Side of Hinge Outside Right Side of Hinge

Left hand Door Right Hand Door

Hand of Hinges
All doors are handed – right or left. The following illustrations
indicate clearly this “handing” as it is understood within the
hardware industry.
A simple method of determining the hand of all loose joint
hinges is to open the hinge full with the countersunk screw
holes in view. If the hinge can be held by the right hand leaf Right Hand

and it does not fall apart, it is a right hand (RH) hinge. If the
hinge must be held by the left hand leaf to keep it from falling
apart, it is a left hand (LH) hinge.
The hand of hinges may be specified by suffixing the symbols
RH or LH to the catalog number.

Left Hand

Hinge Opened Full Mortise

All hinges for full mortise applications are swaged. Normal
swaging on standard and heavy gauge hinges provides a
Hinge Closed clearance of 1/16" when the leaves are parallel.

Hinge Opened
Full Surface
Hinges for full surface applications are not swaged.
Blank hinges are for full surface welded application and
Hinge Closed are always furnished “flat back” unless specified otherwise
when ordered.

Hinge Opened
Beveled Door
Hinges for beveled door applications have one leaf swaged at
an angle of 31/2˚ (1/8" in 2") to maintain proper door and frame
Hinge Closed clearance when doors are beveled on the hinge side. Specify
handing on these hinges.

Hinge with One Leaf Swaged One Leaf Swaged

When only one leaf is swaged, the non-swaged leaf is
approximately 1/16" shorter as a standard. For all hollow metal
door and frame applications, both leaves must be the same
width. On your order, specify “Leaves must be equal”.

One Leaf Swaged Flat

Hinge with One Leaf Swaged Flat
When only one leaf is swaged flat, the non-swaged leaf is
approximately 3/32" shorter as a standard. For all hollow metal
door and frame applications, both leaves must be the same
width. On your order, specify “Leaves must be equal”.

Screws and Fasteners

Templated Screw Holes
Our hinges are manufactured with templated screw hole locations
and tolerances which conform to the American National Standards
Institute (ANSI/BHMA A-156.7). We publish a complete listing of
templates which list the overall hinge size, material gauge and exact
screw hole location. The most current templates are found on our
website [Link]. These templates should
be consulted prior to any door or frame preparation.

Machine and Wood Screws

Shown:
1. 2. 3. 4. 5.
1. Phillips Head Machine Screw
2. Torx Head Machine Screw
3. Torx Head Wood Screw
4. Phillips Head Wood Screw
5. Oval Phillips Head Machine Screw with Grommet Nut

Size of Hinge Machine Screws Wood Screws Size of Hinge Machine Screws

31/2" x 31/2"* 1/
2 " x 10-24 1 x 10 41/2" 1/
2 " x 12-24
3 2" x 5"
1/ 1/
2 " x 10-24 1 x 10 5" 1/
2 " x 12-24
4" x 4"* 1/
2 " x 12-24 11/4 x 12 6" 1/
2 " x 1/4 -20
41/2" x 4" 1/
2 " x 12-24 11/4 x 12
41/2" x 41/2" 1/
2 " x 12-24 11/4 x 12
Swing Clear Hinges
4" x 6" 1/
2 " x 12-24 11/4 x 12
Size of Hinge Machine Screws Wood Screws
4" x 7" 1/
2 " x 12-24 11/4 x 12
41/2" x 6" 1/
2 " x 12-24 11/4 x 12 41/2" 1/
2 x 12-24 11/4 x 12

41/2" x 7" 1/
2 " x 12-24 11/4 x 12 5" 1/
2 x 12-24 11/4 x 12

41/2" x 8" 1/
2 " x 12-24 11/4 x 12
5" x 4" 1/
2 " x 12-24 11/4 x 12
Full Surface Hinges
5" x 41/2" 1/
2 " x 12-24 1/
4 x 12
Thru Bolts &
5" x 5" 1/
2 " x 12-24 11/4 x 12 Size of Hinge Machine Screws
Grommet Nut
5" x 7" 1/
2 " x 12-24 11/4 x 12
41/2" 1/
2 x 12-24 2 x 1/4 -20
5" x 8" 1/
2 " x 12-24 11/2 x 14
5" 1/
2 x 12-24 2 x 1/4 -20
6" x 5" 1/
2 " x 1/4"-20 11/2 x 14
6" 1/
2 x 1/4 -20 2 x 1/4 -20
6" x 6" 1/
2 " x 1/4"-20 11/2 x 14
8" x 6" 1/
2 " x 1/4"-20 11/2 x 14
8" x 8" 1/
2 " x 1/4"-20 11/2 x 14
Half Surface Hinges
Thru Bolts &
Size of Hinge Machine Screws
*1400-1414-1458 Residential Guide Grommet Nut
Size of Hinge Wood Screws 4 1/2" 1/
2 x 12-24 2 x 1/4 -20
3 1/2" x 3 1/2" 3/
4 x9 5" 1/
2 x 12-24 2 x 1/4 -20
4" x 4" 1x9 6" 1/
2 x 1/4 -20 2x 1/
4 -20

Packing:
All full mortise hinges are packed all machine x half
wood screws.

McKinney hinge product finishes meet or exceed the American

National Standards for materials and finishes (ANSI/BHMA -
A156.18 and BHMA 1301).
The Agion antimicrobial is not intended as a substitute for good
Every effort is made to furnish finishes which do comply with hygiene. Coated products must still be cleaned to ensure the
the U.S. Standard. However, we cannot guarantee that our finish surfaces will be free of destructive microbes. ASSA ABLOY makes
will match other manufacturers’ finish. Where a special finish no representations or warranties, express or implied, as to the effi
or a matched finish is required, a sample must be submitted cacy of the Agion antimicrobial. A copy of the Agion warranty is
with the order. available upon request. Agion is a registered trademark of Agion
MicroShield® Technologies, Inc., Wakefi eld, MA, USA
ASSA ABLOY Group companies offer MicroShield®, an
antimicrobial coating for door hardware. MicroShield uses
proven silver ion-based technology from Agion®, a leading
provider of antimicrobial solutions, to stem the spread of
bacteria and other microbes.
MicroShield® is a registered trademark of ASSA ABLOY Access
and Egress Hardware Group, Inc.

Standard Architectural Finishes

BHMA Code BHMA Code McKinney/U.S. Code Finish Description

Non-Ferrous (Brass or Stainless Steel) Ferrous (Steel)
605 (Brass) 632 3 Bright Brass, Clear Coated
606 (Brass) 633 4 Satin Brass, Clear Coated
611 (Bronze) 637 9 Bright Bronze, Clear Coated
612 (Bronze) 639 10 Satin Bronze, Clear Coated
614 (Bronze) 641 10A Antique Bronze, Oil Rubbed and Clear Coated
613 (Bronze) 640 10B Dark Oxidized Satin Bronze, Oil Rubbed
618 (Brass, Bronze) 645 14 Bright Nickel Plated, Clear Coated
619 (Brass, Bronze) 646 15 Satin Nickel Plated, Clear Coated
625 (Brass, Bronze) 651 26 Bright Chrome
626 (Brass, Bronze) 652 26D Satin Chrome
629 (300 Series Stainless) n/a 32 Bright Stainless Steel
630 (300 Series Stainless) n/a 32D Satin Stainless Steel

Custom Architectural Finishes

BHMA Code BHMA Code McKinney/U.S. Code Finish Description

Non-Ferrous (Brass or Stainless Steel) Ferrous (Steel)
609 (Brass) 638 5 Satin Brass, Blackened, Satin Relieved, Clear Coated
610 (Brass) 636 7 Satin Brass, Blackened, Bright Relieved, Clear Coated
616 (Bronze) 643 11 Satin Bronze, Blackened, Satin Relieved, Clear Coated
623 (Bronze) 649 20 Light Oxidized Statuary Bronze, Clear Coated
624 (Bronze) 650 20A Dark Oxidized Statuary Bronze, Clear Coated

Note: Check with factory for availability and pricing on these finishes.

Base Material McKinney/U.S. Code Finish Description

Steel P Primed for Painting
Steel D3 Dark Bronze Powder Coat
Stainless Steel 10BE Dark Oxidized Satin Bronze, Equivalent
Stainless Steel BSP Black Suede Powder Coat
Stainless Steel WSP White Suede Powder Coat
Stainless Steel CPC Clear Powder Coat
Stainless Steel 32DBIO MicroShield Agion Antimicrobial

Note: May not be available on MacPRO or Rescue Hardware.

Product Maintenance & Care

The McKinney line of hinges are manufactured in compliance with all applicable federal and ANSI specifications.
The following are general maintenance tips for providing long life and proper finish appearance.
Hinges must be free swinging without any binding. To align the hinges to prevent binding the use of shims is recommended, if
required. If the hinges begin to make noise, remove any binding conditions, grease or lubricate all moving parts, re-mount the
hinge and re-adjust the hinge with the proper shims.
The hinges come “greased” from the factory, but should be checked on a regular basis for lubrication. ASSA ABLOY recommends
that hinges used in commercial, high frequency applications or in extreme environmental conditions be lubricated annually to
ensure long life and quiet operation.
To lubricate our standard hinge, remove the pin and apply a generous coating of lithium grease and reinsert the pin by driving it
completely down to the shoulder of the pin head.
Hinges sized properly for the door weight, door size and frequency of use will last for a considerable period of time without
maintenance. Hinge screws should be periodically inspected for tightness.
Steel hinges are intended for use on interior applications only. Brass and Stainless steel hinges can be used for either interior or
exterior. All steel will eventually rust and all brass will eventually tarnish. To slow down the corrosion/tarnishing process, a clear
coat of lacquer is applied on the top surface of the steel or brass materials and the finish surface. Plated finishes receive a clear
coating of lacquer to protect against atmospheric conditions.
McKinney stainless steel hinges are made with 304 stainless steel material. Stainless steel is corrosion resistant, but not corrosion
proof. Because there is at least 10.5% of chromium in stainless steel hinges, oxidation can occur which could leads to the
appearance of “red rust”. This red rust could be caused from atmospheric conditions, when hinges are exposed to moist or marine
environments, chemical conditions, such as being exposed to high chloride chemicals cleaners, or contact with steel, copper or
other foreign materials. Never use steel wool to clean stainless steel hinges. Period cleaning is recommended to avoid seeing red
rust on the hinges. We recommend using a general purpose stainless steel cleaner.
Many anti-bacterial cleaners used to clean and sanitize door hardware contain high levels of chlorides which will cause corrosion if not properly rinsed off.
For additional corrosion protection, we recommend ordering stainless steel hinges with a clear powder applied over the base metal, (CPC).

Hinges that come painted or plated are in accordance with ANSI/BHMA finishing standards and ASTM B-117 salt spray standards.
Caution should be used when installing the hinges to avoid damage to the painted or plated finish. To remove dirt, the use of a soft
damp cloth free any chemicals can be used. Abrasive cleaners or lacquer thinners should not be used to clean the surface of the
hinges. To do so will void any warranty of that product..
Any questions about our product, please call us at 1-800-346-7707.

•F
ull mortise bearing hinges are commonly used for the
flush door/frame/wall application
TA3331
• Two knuckle design has a clean finished look
• Specify right or left hand when ordering
TA2731
• Decorative tips are available
• For available finishes see page 28

No. ANSI Cross Reference Base Material Weight

TA3331 A5112 Stainless STD Application
TA2731 A8112 Steel STD

Specifications
Fasteners
No. of
Inches mm Gauge Holes Machine Wood
3 2" x 3 2"
1/ 1/
88.9 x 88.9 .123 6 1/
2 x 10-24 1 x 10
4" x 4" 101.6 x 101.6 .130 8 1/
2 x 12-24 11/4 x 12
41/2" x 4" 114.3 x 101.6 .134 8 1/
2 x 12-24 11/4 x 12 Options:

41/2" x 41/2" 114.3 x 114.3 .134 8 1/

2 x 12-24 11/4 x 12 Code Description

5" x 41/2" 127 x 114.3 .146 8 1/

2 x 12-24 11/4 x 12 NRD Non-Removable Door –
one set screwed hinge
5" x 5" 127 x 127 .146 8 1/
2 x 12-24 11/4 x 12
furnished per set
RC Round Corner – 1/4"
radius furnished unless
Decorative Tip Options (TA2731 only) specified otherwise
FT Flat Tip SSF Safety Stud Feature
RT Round Tip FT RT MM Magnetic Monitoring
GT Grooved Tip QC ElectroLynx® hinge 4 or 8
wire available
LT Lined Tip
Note: Not available on 31/2 " x 31/2" hinges CC Concealed Circuit 4 or 8
GT LT wire available

Approved for NFPA 80 fire rated openings

Two Knuckle Heavy Weight Series

Recommended for use on high frequency and/or heavy wood or metal doors in
schools, hospitals or other public buildings where heavy traffic is experienced.

• Use for the common flush door/frame/wall application TA3350

•H
eavy weight hinges should be used on all extra heavy
TA3750
doors or those exposed to high frequency use
• Two knuckle design has a clean finished look
•F
or Beveled Edge (where doors are beveled on hinge
side) specify TA5350 or TA5750
• Specify right or left hand when ordering
• For available finishes see page 28

Application

No. ANSI Cross Reference Base Material Weight

TA3350 A5111 Stainless HVY
TA3750 A8111 Steel HVY

Specifications
Fasteners
No. of
Inches mm Gauge Holes Machine Wood Options:
4 2" x 4 2"
1/ 1/
114.3 x 114.3 .180 8 1/
2 x 12-24 1 1/
4 x 12 Code Description
5" x 4 2"
1/
127 x 114.3 .190 8 1/
2 x 12-24 1 1/
4 x 12 NRD Non-Removable Door –
one set screwed hinge
5" x 5" 127 x 127 .190 8 1/
2 x 12-24 1 1/
4 x 12
furnished per set
RC Round Corner – 1/4"
radius furnished unless
specified otherwise
SSF Safety Stud Feature
Approved for NFPA 80 fire rated openings
MM Magnetic Monitoring
QC ElectroLynx® hinge 4 or 8
wire available
CC Concealed Circuit 4 or 8
wire available

• Use for the common flush door/frame/wall application TA314

• Decorative tips are available
TA714
• For available finishes see page 28

No. ANSI Cross Reference Base Material Weight

TA314 A5112 Stainless STD
TA314 A2112 Brass STD
Application
TA714 A8112 Steel STD

Specifications
Fasteners
No. of
Inches mm Gauge Holes Machine Wood
3 2" x 3 2"
1/ 1/ *
88.9 x 88.9 .123 6 1/
2 x 10-24 1 x 10
4" x 4"* 101.6 x 101.6 .130 8 1/
2 x 12-24 11/4 x 12
41/2" x 4" 114.3 x 101.6 .134 8 1/
2 x 12-24 11/4 x 12 Options:

41/2" x 41/2" 114.3 x 114.3 .134 8 1/

2 x 12-24 11/4 x 12 Code Description

5" x 41/2"* 127 x 114.3 .146 8 1/

2 x 12-24 11/4 x 12 NRP Non-Removable Pin

5" x 5"* 127 x 127 .146 8 1/

2 x 12-24 11/4 x 12 RC Round Corner – 1/4"
radius furnished unless
* Not available in Brass Base material specified otherwise
HT Hospital Tip
SSF Safety Stud Feature
Decorative Tip Options
QC ElectroLynx® Hinge –
FT Flat Tip 4, 8 or 12 wire available
RT Round Tip FT RT CC Concealed Circuit –
GT Grooved Tip 4, 8 or 12 wire available

LT Lined Tip CC-18 Concealed Circuit – 2, 4,

6, 8 or 10 wire available
BT Ball Tip
GT LT (2-18AWG wires and the
ST Steeple Tip remainder 28AWG wires)
Note: Not available on 31/2 " x 31/2" hinges MM Magnetic Monitoring

Steel & Stainless Approved for

NFPA 80 fire rated openings

Three Knuckle Heavy Weight Series

Recommended for use on high frequency and/or heavy wood or metal doors in
schools, hospitals or other public buildings where heavy traffic is experienced.

•H
eavy weight hinges should be used on all extra heavy
doors or those exposed to high frequency use TA386
• Use for the common flush door/frame/wall application TA786
• Beveled Edge - where doors are beveled on hinge side
specify TA5386 or TA5786
• For available finishes see page 28
• Decorative flat tips are available on 41/2" and 5"

No. ANSI Cross Reference Base Material Weight Application

TA386 A5111 Stainless HVY

TA386 A2111 Brass HVY
TA786 A8111 Steel HVY

Specifications
Fasteners
No. of
Inches mm Gauge Holes Machine Wood
Options:
41/2" x 4" 114.3 x 101.6 .180 8 1/
2 x 12-24 11/4 x 12
Code Description
41/2" x 41/2" 114.3 x 114.3 .180 8 1/
2 x 12-24 11/4 x 12
NRP Non-Removable Pin
5" x 41/2" 127 x 114.3 .190 8 1/
2 x 12-24 11/4 x 12
RC Round Corner – 1/4"
5" x 5"* 127 x 127 .190 8 1/
2 x 12-24 11/4 x 12
radius furnished unless
6" x 5"* 152.4 x 127 .203 10 1/
2 x 1⁄4 -20 11/2 x 14 specified otherwise
6" x 6"* 152.4 x 152.4 .203 10 1/
2 x 1⁄4 -20 11/2 x 14 HT Hospital Tip
SSF Safety Stud Feature
* Not available in Brass Base material.
QC ElectroLynx® Hinge –
4, 8 or 12 wire available
CC Concealed Circuit –
4, 8 or 12 wire available
CC-18 Concealed Circuit –2, 4,
6, 8 or 10 wire available
(2-18AWG wires and the
remainder 28AWG wires)
Steel & Stainless Approved for
MM Magnetic Monitoring
NFPA 80 fire rated openings
FT Flat Decorative Tip
BT Ball Tip

• Institutional hinges feature hospital tipped ends and HTA386

concealed bearing assemblies
HTA786
•T
he prison safety feature is available on
non-electric hinges
• Heavy weight hinges should be used on all extra
heavy doors or those exposed to high frequency use Shown with optional
prison safety feature
• Use for the common flush door/frame/wall application (4½ x 4½ size only)
• Beveled Edge - where doors are beveled on hinge side
specify HTA5386 or HTA5786
• Torx Pin Head Fasteners Available
• For available finishes see page 28
Application
No. ANSI Cross Reference Base Material Weight
HTA386 A5111 Stainless HVY
HTA786 A8111 Steel HVY

Specifications
Fasteners
No. of
Inches mm Gauge Holes Machine Wood
Options:
4 2" x 4 2"
1/ 1/
114.3 x 114.3 .180 8 1/
2 x 12-24 11/4 x 12
Code Description
5" x 41/2"* 127 x 114.3 .190 8 1/
2 x 12-24 11/4 x 12
PSF Prison Safety Feature
* Not Available with PSF option. MM Magnetic Monitoring*
QC ElectroLynx® Hinge –
4, 8 or 12 wire available.
(12 wire not available
with PSF)
CC Concealed Circuit –
4, 8 or 12 wire available.
(12 wire not available
with PSF)

Approved for NFPA 80 fire rated openings * Not Available with PSF option.

Three Knuckle Heavy Weight Series (Reversible)

Recommended for use on high frequency and/or heavy wood or metal doors in
schools, hospitals or other public buildings where heavy traffic is experienced.

•H
inge allows for maximum clearance for passage of beds,
tables or other equipment through doorway
TA795
• Pressed steel jambs require no special reinforcing
• Steel base materials
•F
or Beveled Edge, where doors are beveled on hinge
side, specify TA5795
• For available finishes see page 28

No. ANSI Cross Reference Base Material Weight

TA795 A8121 Steel HVY Application

Specifications
Fasteners
No. of
Inches mm Gauge Holes Machine Wood
4 "
1/
2 114.3 .180 8 1/
2 x 12-24 11/4 x 12
5" 127 .190 8 1/
2 x 12-24 11/4 x 12

Note: The pin is held in place by an NRP set screw which allows the hinge to be reversible.

Options:
Code Description
HT Hospital Tip

Approved for NFPA 80 fire rated openings

• Use for the common flush door/frame/wall application

T2314
• Available on the QuickShip program
•T
2314 stainless steel base material – For available finishes
T2714
see page 28
• T2714 steel base material – For available finishes see
page 28
•F
or Beveled Edge, where doors are beveled on hinge
side, specify T4314 or T4714

No. ANSI Cross Reference Base Material Weight Application

T2314 A5133 Stainless STD

T2714 A8133 Steel STD

Specifications
Fasteners
No. of
Inches mm Gauge Holes Machine Wood
3 2" x 3 2"*
1/ 1/
88.9 x 88.9 .123 6 1/
2 x 10-24 1 x 10
4" x 4" 114.3 x 114.3 .130 8 1/
2 x 12-24 11/4 x 12 Options:

4 2" x 4 2"
1/ 1/
114.3 x 114.3 .134 8 1/
2 x 12-24 11/
4 x 12 Code Description

5" x 41/2" 127 x 114.3 .146 8 1/

2 x 12-24 11/4 x 12 NRP Non-Removable Pin

5" x 5" 127 x 127 .146 8 1/

2 x 12-24 11/4 x 12 RC Round Corner – 1/4"
*Available with reverse hole pattern. radius furnished unless
specified otherwise
HT Hospital Tip
BT Ball Tip
ST Steeple Tip
SSF Safety Stud Feature

McKinney Hinge Pin Door Stop

• Recommended for high-use or high impact doors with McKinney T2714
or TA2714 hinges
• Protects against damage to doors and walls
• Runs the full length of the hinge

Part number Description Finish

76305 Hinge Pin Stop for MacPro MP79 & MPB79 26D
76306 Hinge Pin Stop for McKinney T2714 & TA2714 26D

Five Knuckle Standard Weight Series

Recommended for standard weight, medium frequency doors, or doors with closing devices.

• Use for common flush door/frame/wall applications

•F
or Beveled Edge, where doors are beveled on hinge TA2314
side, specify TA4314 or TA4714
• For available finishes see page 28
TA2714

No. ANSI Cross Reference Base Material Weight

TA2314 A5112 Stainless STD
TA2314 A2112 Brass STD
TA2714 A8112 Steel STD

Specifications
Application
Fasteners
No. of
Inches mm Gauge Holes Machine Wood
3 2" x 3 2"*
1/ 1/
88.9 x 88.9 .123 6 1/
2 x 10-24 1 x 10
4" x 4"* 101.6 x 101.6 .130 8 1/
2 x 12-24 11/4 x 12
4 2" x 4"
1/
114.3 x 101.6 .134 8 1/
2 x 12-24 11/4 x 12
41/2" x 41/2" 114.3 x 114.3 .134 8 1/
2 x 12-24 11/4 x 12
5" x 4 2"*
1/
127 x 114.3 .146 8 1/
2 x 12-24 11/4 x 12
5" x 5"* 127 x 127 .146 8 1/
2 x 12-24 11/4 x 12
6" x 6"* 152.4 x 152.4 .160 10 1/
2 x 1/4 -20 11/2 x 14

* Not available in Brass base material.

Options:

Code Description Code Description Code Description

NRP Non-Removable Pin GT Grooved Tip* CC-18 Concealed Circuit – 2, 4,
6, 8 or 10 wire available
TB Ball Bearing LT Lined Tip* (2-18AWG wires and the
TCA Concealed Bearing RT Round Tip* remainder 28AWG wires)

RC Round Corner – 1/4" ST Steeple Tip MM Magnetic Monitoring

radius furnished unless QC ElectroLynx® Hinge –
specified otherwise SSF Safety Stud Feature
4, 8 or 12
HT Hospital Tip CC Concealed Circuit – wire available
4, 8, or 12
BT Ball Tip wire available
FT Flat Tip*
*Not available on 3-1/2" and 6" sizes
Steel & Stainless Approved for NFPA 80 fire rated openings

McKinney Hinge Pin Door Stop

• Recommended for high-use or high impact doors with McKinney T2714
or TA2714 hinges
• Protects against damage to doors and walls
• Runs the full length of the hinge

Part number Description Finish

76305 Hinge Pin Stop for MacPro MP79 & MPB79 26D
76306 Hinge Pin Stop for McKinney T2714 & TA2714 26D

Concealed Bearing
• Use for common flush door/frame/wall applications TCA2314
•F
or Beveled Edge, where doors are beveled on hinge
side, specify TCA4314 or TCA4714
TCA2714
• For available finishes see page 28

No. ANSI Cross Reference Base Material Weight

TCA2314 A5112 Stainless STD
TCA2714 A8112 Steel STD
Application

Specifications
Fasteners
No. of
Inches mm Gauge Holes Machine Wood
41/2" x 4"* 114.3 x 101.6 .134 8 1/
2 x 12-24 11/4 x 12
41/2" x 41/2"* 114.3 x 114.3 .134 8 1/
2 x 12-24 11/4 x 12
5" x 41/2"* 127 x 114.3 .146 8 1/
2 x 12-24 11/4 x 12
5" x 5"* 127 x 127 .146 8 1/
2 x 12-24 11/4 x 12 Options:
Code Description
* Not available in Brass base material.
NRP Non-Removable Pin
RC Round Corner – 1/4"
radius furnished unless
specified otherwise
HT Hospital Tip
BT Ball Tip
ST Steeple Tip
SSF Safety Stud Feature
QC ElectroLynx® Hinge –
4, 8 or 12 wire available
CC Concealed Circuit –
4, 8 or 12 wire available
Approved for NFPA 80 fire rated openings
CC-18 Concealed Circuit – 2, 4,
6, 8 or 10 wire available
(2-18AWG wires and the
remainder 28AWG wires)
MM Magnetic Monitoring

Five Knuckle Standard Weight Series

Wide throw hinges are utilized where a door is recessed from the face of the frame.

• The wide throw full mortise bearing hinge is

recommended for use on standard weight, medium
TA2398
frequency doors where it is necessary to open the door TA2798
around a large reveal
•F
or information on calculating the proper width of a wide
throw hinge see page 16
•F
or Beveled Edge, where doors are beveled on hinge
side, specify TA4398 or TA4798
• For available finishes see page 28

Application

No. ANSI Cross Reference Base Material Weight

TA2398 A5112 Stainless STD
TA2798 A8112 Steel STD

Specifications
Fasteners
No. of
Inches mm Gauge Holes Machine Wood
3 2" x 5"
1/
88.9 x 127 .123 6 1/
2 x 10-24 1 x 10 Options:
31/2" x 6" 88.9 x 152.4 .123 6 1/
2 x 10-24 1 x 10 Code Description
4" x 6" 114.3 x 152.4 .130 8 1/
2 x 12-24 11/4 x 12 NRP Non-Removable Pin
41/2" x 6" 114.3 x 152.4 .134 8 1/
2 x 12-24 11/4 x 12 TB Ball Bearing
41/2" x 8" 114.3 x 203.2 .134 8 1/
2 x 12-24 11/4 x 12 TCA Concealed Bearing

5" x 7" 127 x 177.8 .146 8 1/

2 x 12-24 11/4 x 12 RC Round Corner – 1/4"
radius furnished unless
specified otherwise
HT Hospital Tip
BT Ball Tip
ST Steeple Tip
SSF Safety Stud Feature
Approved for NFPA 80 fire rated openings QC ElectroLynx® Hinge –
4, 8 or 12 wire available*

CC Concealed Circuit –
4, 8 or 12 wire available*
CC-18 Concealed Circuit –
2, 4, 6, 8 or 10 wire
available (2-18AWG
wires and the remainder
28AWG wires)*
MM Magnetic Monitoring
* Maximum 6" width.

•H
eavy weight hinges should be used on all extra heavy T4A3386
doors or those exposed to high frequency use
T4A3786
• T4A3386- Stainless steel base or available in brass base
material polished
• T4A3786- Steel base material
•F
or Beveled Edge, where doors are beveled on hinge
side, specify T4A4386 or T4A4786
• For available finishes see page 28

Note: 8" x 6" and 8" x 8" have six bearings. Specify T6B3386 or T6B3786. Application

No. ANSI Cross Reference Base Material Weight

T4A3386 A5111 Stainless HVY
T4A3386 A2111 Brass HVY
T4A3786 A8111 Steel HVY

Specifications Options:
Fasteners Code Description
No. of
Inches mm Gauge Holes Machine Wood NRP Non-Removable Pin
41/2" x 4" 114.3 x 101.6 .180 8 1/
2 x 12-24 11/4 x 12 T4B Ball Bearing
41/2" x 41/2" 114.3 x 114.3 .180 8 1/
2 x 12-24 11/4 x 12 TCA Concealed Bearing
5" x 4 2"
1/
127 x 114.3 .190 8 1/
2 x 12-24 11/
4 x 12 RC Round Corner – 1/4"
radius furnished unless
5" x 5"* 127 x 127 .190 8 1/
2 x 12-24 11/4 x 12
specified otherwise
6" x 5"* 152.4 x 127 .203 10 1/
2 x 1/4 -20 11/2 x 14
HT Hospital Tip
6" x 6"* 152.4 x 152.4 .203 10 1/
2 x 1/4 -20 11/2 x 14
BT**** Ball Tip
8" x 6"** 203.2 x 125.4 .203 16 1/
2 x 1/4 -20 11/2 x 14
FT **** Flat Tip
8" x 8"*** 203.2 x 203.2 .203 16 1/
2 x 1/4 -20 11/2 x 14
ST**** Steeple Tip

* Not available in brass base material. SSF Safety Stud Feature

** Available in steel only. RB Raised Barrel*
***Available in stainless steel only.
****FT tips not offered on 6" and 8" sizes, BT and ST not offered on 8" sizes. QC ElectroLynx® Hinge –
4, 8 or 12 wire available
CC Concealed Circuit –
4, 8 or 12 wire available
CC-18 Concealed Circuit – 2, 4,
6, 8 or 10 wire available
Steel & Stainless Approved for (2-18AWG wires and the
NFPA 80 fire rated openings remainder 28AWG wires)
MM Magnetic Monitoring

* Refer to page SP-3 for Raised Barrel.

Five Knuckle Heavy Weight Full Mortise Series

Recommended for use on high frequency and/or heavy wood or metal doors in
schools, hospitals or other public buildings where heavy traffic is experienced.

Concealed Bearing TCA3386

•H
eavy weight hinges should be used on all extra heavy
TCA3786
doors or those exposed to high frequency use
• TCA3386 – Stainless steel base
• TCA3786 – Steel base material
•F
or Beveled Edge, where doors are beveled on hinge
side, specify TCA4386 or TCA4786
• For available finishes see page 28

Application

No. ANSI Cross Reference Base Material Weight

TCA3386 A5111 Stainless HVY
TCA3786 A8111 Steel HVY

Specifications
Fasteners Options:
No. of
Inches mm Gauge Holes Machine Wood Code Description
4 2" x 4"*
1/
114.3 x 101.6 .180 8 1/
2 x 12-24 1 1/
4 x 12 NRP Non-Removable Pin
4 2" x 4 2"*
1/ 1/
114.3 x 114.3 .180 8 1/
2 x 12-24 1 1/
4 x 12 RC Round Corner – 1/4"
5" x 41/2"* 127 x 114.3 .190 8 1/
2 x 12-24 11/4 x 12 radius furnished unless
specified otherwise
5" x 5"* 127 x 127 .190 8 1/
2 x 12-24 11/4 x 12
HT Hospital Tip

* Not available in brass base material. BT Ball Tip

ST Steeple Tip
SSF Safety Stud Feature
QC ElectroLynx® Hinge –
Approved for NFPA 80 fire rated openings 4, 8 or 12 wire available
CC Concealed Circuit –
4, 8 or 12 wire available
CC-18 Concealed Circuit – 2, 4,
6, 8 or 10 wire available
(2-18AWG wires and the
remainder 28AWG wires)
MM Magnetic Monitoring

No. ANSI Cross Reference Base Material Weight

T4A3386 A5111 Stainless HVY
T4A3786 A8111 Steel HVY

Specifications
Fasteners
No. of Options:
Inches mm Gauge Holes Machine Wood
Code Description
41/2" x 5" 114.3 x 127 .180 8 1/
2 x 12-24 11/4 x 12
NRP Non-Removable Pin
41/2" x 6" 114.3 x 152.4 .180 6 1/
2 x 10-24 11/4 x 12
T4B Ball Bearing
41/2" x 7" 114.3 x 177.8 .180 8 1/
2 x 12-24 11/4 x 12
TCA Concealed Bearing
41/2" x 8" 114.3 x 203.2 .180 8 1/
2 x 12-24 11/4 x 12
RC Round Corner – 1/4"
5" x 6" 127 x 152.4 .190 8 1/
2 x 12-24 11/4 x 12 radius furnished unless
5" x 7" 127 X 177.8 .190 8 1/
2 x 12-24 11/4 x 12 specified otherwise

5" x 8" 127 X 203.2 .190 8 1/

2 x 12-24 11/4 x 12 HT Hospital Tip
BT Ball Tip
ST Steeple Tip
SSF Safety Stud Feature
QC ElectroLynx® Hinge –
4, 8 or 12 wire available*
CC Concealed Circuit –
Approved for NFPA 80 fire rated openings 4, 8 or 12 wire available*
MM Magnetic Monitoring

*Q
C and CC options available on
hinges up to 6" wide.

Five Knuckle Standard Weight Swing Clear Series (Reversible)

Swing Clear Hinges create barrier free openings by moving the hinge barrel
and door edge out of the way.

•R
ecommended for use on standard weight, medium
frequency doors in schools, hospitals or other TA2395
public buildings TA2895
•H
inge allows for maximum clearance for passage of
beds, tables or other equipment through the doorway
• Meets ADA Requirements and ANSI A117.1-1986
• Pressed steel jambs require no special reinforcing
• Pin is held in place by an NRP set screw, which allows
the hinge to be reversible
•F
or Beveled Edge, where doors are beveled on hinge
Application
side, specify TA4895 or TA4395
• For available finishes see page 28

No. ANSI Cross Reference Base Material Weight

TA2395 N/A Stainless STD
TA2895 A8122 Steel STD

Specifications
Fasteners
No. of Options:
Inches mm Gauge Holes Machine Wood
Code Description
41/2" 114.3 .134 8 1/
2 x 12-24 11/4 x 12
TB Ball Bearing
5"* 127 .146 8 1/
2 x 12-24 11/2 x 12
HT Hospital Tip

*Not Available with electric options QC ElectroLynx® Hinge –

4, 8 or 12 wire available
in 4-1/2" US26D and
US32D only
CC Concealed Circuit –
Approved for NFPA 80 fire rated openings 4, 8 or 12 wire available
in 4-1/2" US26D and
US32D only

• Recommended for use on high frequency and/or heavy T4A3395

wood or metal doors in schools, hospitals or other
public buildings where heavy traffic is experienced T4A3795
•H
inge allows for maximum clearance for passage of
beds, tables or other equipment through the doorway
• Meets ADA Requirements and ANSI A117.1-1986
• Pressed steel jambs require no special reinforcing
•P
in is held in place by an NRP set screw, which allows
the hinge to be reversible
• For Beveled Edge, where doors are beveled in hinge
Application
side, specify T4A4395 or T4A4795
• For available finishes see page 28

No. ANSI Cross Reference Base Material Weight

T4A3395 A5121 Stainless HVY
T4A3795 A8121 Steel HVY

Specifications
Fasteners
No. of Options:
Inches mm Gauge Holes Machine Wood
Code Description
41/2" 114.3 .180 8 1/
2 x 12-24 11/4 x 12
TB Ball Bearing
5" 127 .190 8 1/
2 x 12-24 11/4 x 12
HT Hospital Tip
QC ElectroLynx® Hinge –
4, 8 or 12 wire available
in 4-1/2" and 5" US26D
and US32D only
CC Concealed Circuit –
4, 8 or 12 wire available
in 4-1/2" and 5" US26D
and US32D only

Approved for NFPA 80 fire rated openings

MacPro® Five Knuckle Standard Weight Series

The MacPro line offers contractor grade hinges to get the job done
right. High quality MacPro hinges are an extraordinary value, ideal
when you need large quantities of standard hinges.

• Plain bearing hinges are for standard weight doors only

MP79
•F
or standard weight doors with a closing device, MPB79
or MPB91 bearing hinge must be used
• MacPro templated hinges are made to conform to
ANSI/BHMA 156.1, 156.7
• For available finishes consult the factory

ANSI Cross MPB79

No. Reference Base Material Weight Bearing MPB91
MP79 A8133 Steel STD Plain
Bearing
MP91 5133 Stainless* STD Plain
MPB79 A8112 Steel STD Bearing
MPB91 A5112 Stainless STD Bearing

*41/2" x 41/2"
Application

Specifications
Fasteners
No. of
Inches mm Gauge Holes Machine Wood
4 2" x 4"
1/
114.3 x 101.6 .134 8 1/
2 x 12-24 11/4 x 12
41/2" x 41/2" 114.3 x 114.3 .134 8 1/
2 x 12-24 11/4 x 12

Options:
MPB79 & MPB68 - Approved for NFPA 80 fire rated openings
Code Description
NRP Non-Removable Pin

McKinney Hinge Pin Door Stop

• Recommended for high-use or high impact doors with MacPro MP79 &
MPB79 hinges
• Protects against damage to doors and walls
• Runs the full length of the hinge
Part number Description Finish
76305 Hinge Pin Stop for MacPro MP79 & MPB79 26D
76306 Hinge Pin Stop for McKinney T2714 & TA2714 26D

• For doors with a closing device, bearing hinge

MPB99
must be used MPB68
• For heavy weight doors with a closing device, select a
MPB68, heavy weight bearing hinge
• MacPro templated hinges are made to conform to
ANSI/BHMA 156.1, 156.7
• For available finishes consult the factory

Application

ANSI
Cross
No. Reference Base Material Weight Bearing
MPB99 A5111 Stainless HVY Bearing
MPB68 A8111 Steel HVY Bearing

Specifications
Fasteners
No. of
Inches mm Gauge Holes Machine Wood Options:
41/2" x 41/2" 114.3 x 114.3 .180 8 1/
2 x 12-24 11/4 x 12 Code Description
5" x 41/2" 127 x 114.3 .190 8 1/
2 x 12-24 11/4 x 12 NRP Non-Removable Pin

Approved for NFPA 80 fire rated openings

•R
ecommended for use on high frequency and/or heavy TA391
wood or metal doors in schools, hospitals or other public
buildings where heavy traffic is experienced TA791
• For use with concealed door holders or door closers
• Set includes one anchor hinge and two 5" x 41/2" full
mortise hinges
• Sets require handing and are packed with all machine
and all wood screws
•T
he pin is inserted from the bottom of the barrel on the
anchor hinge, and is held in place by an NRP set screw
• Anchor plate for door header only, permits use of
holders and closers concealed in the top of the jamb
• For Beveled Edge, where doors are beveled in hinge
side, specify TA5391 or TA5791
• TA391 available in 26D and 32D
• TA791 available in 26D
Application

No. ANSI Cross Reference Base Material Weight

TA391 A5551 Stainless HVY
TA791 A8551 Steel HVY

Specifications
Fasteners
No. of
Inches mm Gauge Holes Machine Wood
5" x 4 2"
1/
127 x 114.3 .190 13 1/
2 x 12-24 11/4 x 12
Options:
Code Description
QC* ElectroLynx® Hinge –
4, 8 or 12 wire available
*On center of hinge set only.

Approved for NFPA 80 fire rated openings

Three Knuckle Heavy Weight Anchor Hinge Series –

Surface Applied Door Closers
Anchor hinge sets are used on doors where high traffic, abuse, or other door
hardware place an unusual strain on the door, jamb, and hinges.

• Recommended for use on high frequency and/or heavy

wood or metal doors in schools, hospitals or other TA392
public buildings where heavy traffic is experienced TA792
•A
nchor plate for jamb and door header permits use of
surface applied holders and closers
• Set includes one anchor hinge and two 5" x 41/2" full
mortise hinges. One mortise hinge can be electrified
• Sets require handing and are packed with all machine
and all wood screws
•T
he pin is inserted from the bottom of the barrel
on the anchor hinge, and is held in place by an NRP
set screw
•F
or Beveled Edge, where doors are beveled in hinge
side, specify TA5392 or TA5792
• TA392 available in 26D and 32D
• TA792 available in 26D Application

No. ANSI Cross Reference Base Material Weight

TA392 A5551 Stainless HVY
TA792 A8551 Steel HVY

Specifications
Fasteners
No. of
Inches mm Gauge Holes Machine Wood
5" x 4 2"
1/
127 x 114.3 .190 17 1/
2 x 12-24 11/4 x 12
Options:
Code Description
QC * ElectroLynx® Hinge –
4, 8 or 12 wire available
*On center hinge of set only.

Approved for NFPA 80 fire rated openings

•R
ecommended for use on high frequency and/or heavy
wood or metal doors in schools, hospitals or other public TA393
buildings where heavy traffic is experienced
• For use with concealed door holders or door closers
• Set includes one anchor hinge and two 5" x 41/2" full
mortise hinges
• Sets require handing and are packed with all machine
and all wood screws
•T
he pin is inserted from the bottom of the barrel on the
anchor hinge, and is held in place by an NRP set screw
Application
• Anchor plate for jamb header only, permits use of
holders and closers concealed in the top of the door
• For Beveled Edge, where doors are beveled in hinge
side, specify TA5393
• TA393 available in 26D and 32D

Options:
No. ANSI Cross Reference Base Material Weight
Code Description
TA393 A5551 Stainless HVY
QC* ElectroLynx® Hinge –
4, 8 or 12 wire available
Specifications * On center hinge of set only.
Fasteners
No. of
Inches mm Gauge Holes Machine Wood
5" x 41/2" 127 x 114.3 .190 12 1/
2 x 12-24 11/4 x 12

Approved for NFPA 80 fire rated openings

Three Knuckle Heavy Weight Anchor Hinge Series – With 4" Door Leg
Anchor hinge sets are used on doors where high traffic, abuse, or other door
hardware place an unusual strain on the door, jamb, and hinges.

• Recommended for use on high frequency and/or heavy

wood or metal doors in schools, hospitals or other TA394
public buildings where heavy traffic is experienced TA794
•S
et includes one anchor hinge and two 5" x 41/2" full
mortise hinges
• Sets require handing and are packed with all machine
and all wood screws
•T
he pin is inserted from the bottom of the barrel
on the anchor hinge, and is held in place by an NRP
set screw Application
•A
nchor plate for jamb and door header permits use of
surface applied holders and closers
•F
or Beveled Edge, where doors are beveled in hinge
side, specify TA5394 or TA5794
• TA394 available in 26D and 32D
• TA794 available in 26D

No. ANSI Cross Reference Base Material Weight

TA394 A5551 Stainless HVY
TA794 A8551 Steel HVY
Options:
Code Description
Specifications
QC* ElectroLynx® Hinge –
Fasteners 4, 8 or 12 wire available
No. of
Inches mm Gauge Holes Machine Wood * On center hinge of set only.

5" x 4 2"
1/
127 x 114.3 .190 14 1/
2 x 12-24 1 1/
4 x 12

Approved for NFPA 80 fire rated openings

•R
ecommended for use on average frequency and/or
medium weight wood or metal doors in schools, hospitals TA3374
or other public buildings where medium TA2774
traffic is experienced
• The hinges may be used on channel iron jambs
• The jamb leaf is applied to the surface of the jamb
with machine screws. The door leaf is mortised into
the edge of the door
•T
he pin is held in place by an NRP set screw, which
allows the hinge to be reversible
•F
or Beveled Edge, where doors are beveled in hinge
side, specify TA4374 or TA4774
• For TA2774 available finishes see page 29 Application

• TA3374 available in 32D

No. ANSI Cross Reference Base Material Weight

TA3374 A522 Stainless STD
TA2774 A822 Steel STD

Specifications
Options:
Fasteners
No. of
Code Description
Inches mm Gauge Holes Machine
TB Ball Bearing
41/2" 114.3 .134 7 1/
2 x 12-24
HT Hospital Tip
5" 127.0 .146 8 1/
2 x 12-24

Approved for NFPA 80 fire rated openings

Five Knuckle Heavy Weight Half Mortise Series (Reversible)

Half Mortise Bearing Heavy Weight Hinges are for greater frequency and weight
than Plain Bearing or standard hinges

• Recommended for use on high frequency and/or heavy

wood or metal doors in schools, hospitals or other T4A3384
public buildings where heavy traffic is experienced T4A3784
• The hinges may be used on channel iron jambs
• The jamb leaf is applied to the surface of the jamb
with machine screws. The door leaf is mortised into
the edge of the door
•T
he pin is held in place by an NRP set screw, which
allows the hinge to be reversible
• For Beveled Edge, where doors are beveled in hinge
side, specify T4A4384 or T4A4784
• T4A3384 available in 32D, T4A3784 available in P and 26D

No. ANSI Cross Reference Base Material Weight Application

T4A3384 A5211 Stainless HVY

T4A3784 A8211 Steel HVY

Specifications
Fasteners
No. of
Inches mm Gauge Holes Machine
41/2" 114.3 .180 7 1/
2 x 12-24
Options:
5" 127.0 .190 8 1/
2 x 12-24
Code Description
6"* 152.4 .203 9 1/
2 x 1/4 -20
T4B Ball Bearing
* Advise door thickness 1 4" or 2 4"
3/ 1/
HT Hospital Tip

Approved for NFPA 80 fire rated openings

• Recommended for use on high frequency and/or heavy

wood or metal doors in schools, hospitals or other T4A3789
public buildings where heavy traffic is experienced
• The hinges may be used on channel iron jambs
• The jamb leaf is applied to the surface of the jamb
with machine screws. The door leaf is mortised into
the edge of the door
•T
he pin is held in place by an NRP set screw, which
allows the hinge to be reversible
• For Beveled Edge, where doors are beveled in hinge
side, specify T4A4789
• Available in 26D

No. ANSI Cross Reference Base Material Weight Application

T4A3789 A8221 Steel HVY

Specifications
Fasteners
No. of
Inches mm Gauge Holes Jamb Machine Door Machine Door Wood
5" 127.0 .190 8 1/
2 x 1/4 -20 1/
2 x 12-24 1 1/4 x 12

Options:
Code Description
T4B Ball Bearing
HT Hospital Tip

Approved for NFPA 80 fire rated openings

Steel Security
Recommended for use on average frequency and/or medium weight wood or
metal doors in schools, hospitals or other public buildings where medium traffic
is experienced.

• Standard weight half surface hinges are packed with TA2372

Half Surface
all machine screws and thru bolts and grommet nuts TA2772
• The jamb leaf is fastened into the mortise with machine

3500 Series Stainless

screws. The door leaf is applied full surface with thru
bolts and grommet nuts
•T
he pin is held in place by an NRP set screw, which
allows the hinge to be reversible
•S
pecify if the door thickness is greater than 13/4" to insure
that proper bolt is packed
• For available finishes see page 28

No. ANSI Cross Reference Base Material Weight

TA2372 A5412 Stainless STD Application

TA2772 A8412 Steel STD

Specifications
Fasteners
No. of Jamb
Inches mm Gauge Holes Machine Door Machine
41/2" 114.3 .134 7 1/
2 x 12-24 2x 1/
4 -20
5" 127.0 .146 8 1/
2 x 12-24 2x 1/
4 -20

Options:
Code Description
BP-10 Back Plate*
TB Ball Bearing
HT Hospital Tips

* Refer to page HS-8 for BP-10.

Approved for NFPA 80 fire rated openings

Five Knuckle Heavy Weight Series (Reversible)

Recommended for use on high frequency and/or heavy weight wood or metal doors
in schools, hospitals or other public buildings where heavy traffic is experienced.

• Heavy weight half surface hinges are packed with all T4A3382
machine screws and thru bolts and grommet nuts T4A3782
• The jamb leaf is fastened into the mortise with machine
screws. The door leaf is applied full surface with thru
bolts and grommet nuts
• The pin is held in place by an NRP set screw, which
allows the hinge to be reversible
•S
pecify if the door thickness is greater than 13/4" to insure
that proper bolt is packed
• For available finishes see page 28

No. ANSI Cross Reference Base Material Weight Application

T4A3382 A5411 Stainless HVY

T4A3782 A8411 Steel HVY

Specifications
Machine Screws
No. of
Inches mm Gauge Holes Door Jamb
41/2" 114.3 .180 7 2 x 1/4 -20 1/
2 x 12-24
5" 127.0 .190 8 2 x 1/4 -20 1/
2 x 12-24
6"* 152.4 .203 10 2 x 1/4 -20 1/
2 x 1/4 -20

Options:
*Advise door thickness 13/4" or 2 1/4".
Code Description
BP-10 Back Plate*
TB Ball Bearing
HT Hospital Tip

* Refer to page HS-8 for BP-10.

Approved for NFPA 80 fire rated openings

• Recommended for use on high frequency and/or heavy

wood or metal doors in schools, hospitals or other T4A3796
public buildings where heavy traffic is experienced
• Swing clear heavy weight half surface hinges are
packed with all machine screws and thru bolts and
grommet nuts
• The jamb leaf is fastened into the mortise with machine
screws. The door leaf is applied full surface with thru
bolts and grommet nuts
• The pin is held in place by an NRP set screw, which
allows the hinge to be reversible
•S
pecify if the door thickness is greater than 13/4" to insure
that proper bolt is packed Application
• Available in 26D

No. ANSI Cross Reference Base Material Weight

T4A3796 A8421 Steel HVY

Specifications
Machine Screws
No. of
Inches mm Gauge Holes Door Jamb
5" 127.0 .190 9 2x 1/
4 -20 1/
2 x 12-24

Options:
Code Description
HT Hospital Tip
T4B Ball Bearing

Approved for NFPA 80 fire rated openings

Hinge Back Plate

Recommended for use with Half Surface Hinges.

• Available to fit popular half surface hinges

• For finishes see page 29

No. For Use With Base Material

BP-10 TA2772, T4A3782 Steel
BP-11 T4A3796 Steel

Specifications
No. of
No. Inches mm Holes
BP-10 41/2" 114.3 3
BP-10 5" 127.0 4
BP-11 5" 127.0 5

BP-11

• The hinges may be used on channel iron frames

T4A3381
• The narrow leaf is applied to the surface of the jamb
with machine screws. The door leaf is applied to the T4A3781
surface of the door with thru bolts and grommet nuts
• Heavy weight full surface hinges are packed with all
machine screws and thru bolts and grommet nuts
• The pin is held in place by an NRP set screw, which
allows the hinge to be reversible
• T4A3381 available in 32D, T4A3781 available in P and 26D
•S
pecify if the door thickness is greater than 13/4" to insure that
proper bolt is packed

No. ANSI Cross Reference Base Material Weight

Application
T4A3381 A5311 Stainless HVY
T4A3781 A8311 Steel HVY

Specifications
Machine Screws
No. of
Inches mm Gauge Holes Door Jamb
41/2" 114.3 .180 6 2 x 1/4 -20 1/
2 x 12-24
5" 127.0 .180 8 2 x 1/4 -20 1/
2 x 12-24
6" 152.4 .203 9 2 x 1/4 -20 1/
2 x 1/4 -20
Options:
Code Description
T4B Ball Bearing
HT Hospital Tip

Approved for NFPA 80 fire rated openings

Five Knuckle Standard Weight Series (Reversible)

Recommended for use on average frequency and/or medium weight wood or metal doors
in schools, hospitals or other public buildings where medium traffic is experienced.

• The hinges may be used on channel iron jambs

TA2371
• The narrow leaf is applied to the surface of the jamb
with machine screws. The door leaf is applied to the TA2771
surface of the door with thru bolts and grommet nuts
• Standard weight full surface hinges are packed with all
machine screws and thru bolts and grommet nuts
•T
he pin is held in place by an NRP set screw, which
allows the hinge to be reversible
•S
pecify if the door thickness is greater than 13/4" to insure
that proper bolt is packed
•F
or TA2771 available finishes see page 28, TA2371
available in 32D

Application
No. ANSI Cross Reference Base Material Weight
TA2371 A5312 Stainless STD
TA2771 A8312 Steel STD

Specifications
Machine Screws
No. of
Inches mm Gauge Holes Door Jamb
41/2" 114.3 .134 6 2 x 1/4 -20 1/
2 x 12-24
5" 127.0 .146 8 2 x 1/4 -20 1/
2 x 12-24
Options:
Code Description
T4B Ball Bearing
HT Hospital Tip

Approved for NFPA 80 fire rated openings

• Spring hinges are an alternative to door closing

devices. For maximum performance it is recommended to 1502
use all spring hinges on the door. 1552
• This non-handed spring hinge series is adjustable
and tension can be added or reduced by means of
a hex key that is provided
• Caution: Use of gasketing for smoke or sound protection,
wind conditions or unbalanced air pressure, twisted or
misaligned frames or doors, door bottoms, improper latch
adjustment may prevent doors from latching. Additional
spring hinges may be required.
• For available finishes see page 28

Application
No. ANSI Cross Reference Base Material Weight
1502 K81081 Steel STD
1502 K81081F Steel STD
1552 K51071 Stainless Steel STD
1552 K51071F Stainless Steel STD

Specifications
Fasteners
No. of
Inches mm Gauge Holes Machine Wood
4" x 4"* 101.6 x 101.6 .130 8 1/
2 x 12-24 11/4 x 12
41/2" x 4" 114.3 x 101.6 .134 8 1/
2 x 12-24 11/4 x 12
41/2" x 41/2" 114.3 x 114.3 .134 8 1/
2 x 12-24 11/4 x 12

*Not available in 1552.

Approved for NFPA 80 fire rated openings

MacPro® Adjustable Spring Hinge

MacPro offers contract grade hinges to get the job done right.
They are a key player in very competitive jobs, especially in the retrofit arena.

• Recommended for standard weight hinge applications

requiring self-closing control, such as apartments, MPS60
hotels, motels, dormitories, office buildings, etc MPS679
• Spring hinges are an alternative to door closing
devices. Generally two hinges on the door must be
spring hinges to provide adequate closing force
NFPA requires a minimum of two (2) spring hinges on
labeled doors
• MPS679 - Set of two MPS60 spring hinges and one
MPB79 full mortise butt hinge
• MacPro templated hinges are made to conform to
ANSI/BHMA 156.1, 156.7, 156.17
• MPS60 Finishes available: P - Prime Coat, 15, 26D, Application
10BE and BSP
• MPS679 available in 26D

Approved for NFPA 80 fire rated openings

• This economical series is designed to be surface applied

to the door and frame
451
• Coil springs made of high grade steel wire
• Adjustable tension, no special tools required
452
• Wrought steel brackets prevent breakage 453
• All 450 Series are finished in BSP and are packed
with 1x12 wood screws

No. ANSI Cross Reference Base Material Weight

451 K87441 Steel HVY
452 K87441 Steel HVY
453 K87441 Steel HVY

Specifications
Fasteners
No. of
Number Overall Length Spring Length Holes Wood
451 9" 5" 6 1 x 12
452 11" 7" 6 1 x 12
453 13" 9" 6 1 x 12

Jamb Mount Pivot Set

Recommended for installations on average frequency double acting
doors in schools, hospitals, institutions and other public buildings.

• Used in conjunction with CSS-9 Combinations Strike

and Stops and DS-6 Emergency Door Stops
• Thrust steel ball bearing in bottom pivot, oil
impregnated bronze bearing in top pivot
• Center Hung
• Mortised into side jamb
• Full mortise top pivot
• Non-handed
• 15/32 radius heel edge of door
• Maximum Door Weight (interior or exterior) up to
125 lbs 3'6" x 8'0"
• All EP-5J Pivot sets are packed with 14 x 11/2" wood
screws and 1/4 -20 x 5/8" machine screws
• Ferrous base pivot set polished and plated 26D

Specifications
No. ANSI Cross Reference Base Material
EP-5J C07042 Steel

Door Weight Chart

(lbs per square foot)

Door Thickness
13/4" 2"
Aluminum 31/
2 lbs 5 lbs
Wood-
Particle Core 5 lbs 53/4 lbs
Wood-
Stave Block Core 4 lbs 41/2 lbs
14 Gauge
Hollow Metal 83/4 lbs 10 lbs
16 Gauge
Hollow Metal 71/2 lbs 81/2 lbs
18 Gauge
Hollow Metal 61/2 lbs 71/2 lbs

• Manufactured for use with cylindrical or bored locks

CSS-9
Offset Hung
• Cannot be used with deadbolts
• Can be manufactured for the following mortise locks:
– Sargent 7900 and 8200 (no deadbolt function)
– Corbin Russwin ML2000 (no deadbolt function)
– Yale 8800 (no deadbolt function)
– When ordering, specify lock model and function
•A
vailable in offset or center hung latch bolt location
for frame sizes 53/4", 57/8" and 63/4" CSS-9
•C
ustom units available for frame sizes 31/2" to 10"
Center Hung
consult factory for availability
• For use on 13/4" thick doors
• All Combination Strike and Stops are packed with
2 x 8-32 machine screws
1/

• Available in brass material polished and plated 26D

Application

No. ANSI Cross Reference Base Material

CSS-9 A1882 Brass

Specifications
Fasteners
No. of
Inches mm Gauge Holes Machine
5 4"
3/
146.1 .095 6 1/
2 x 8-32
5 8"
7/
149.2 .095 6 1/
2 x 8-32
6 4"
3/
171.5 .095 6 1/
2 x 8-32

Emergency Door Stop

Recommended for installation with our EP-5J pivot in schools, hospitals, institutions
and other public buildings. This unit allows center hung or 1/8" inset doors to be
opened in both directions without damaging the frame.

• Used to convert double acting doors hung on center DS-6

pivots to single acting doors
• Emergency release allows door to swing open in the
opposite direction
• Mortise only on frame
• Latch releases with a touch of the finger
• Second touch of lever returns latch to original position
• Available in brass material polished and plated 26D
•A
ccepted by the New York State Office of Mental Health
(OMH) for use in high risk areas

No. ANSI Cross Reference Base Material

DS-6 A1882 Brass

Specifications
Fasteners Application
No. of
Inches mm Gauge Holes Machine
Surface Plate 41/2" x 15/8" 114.3 x 41.3 .134 4 1/
2 x 12-24
Bolt height 13/4" 44.5

DLS-8
• Manufactured for use with cylindrical or bored locks
• Cannot be used with deadbolts
• Can be manufactured for the following mortise locks:
– Sargent 7900 and 8200 (no deadbolt function)
– Corbin Russwin ML2000 (no deadbolt function)
– Yale 8800 (no deadbolt function)
– When ordering, specify lock model and function
• Available in offset or center hung
• Latch bolt location for frame sizes 53/4 and 63/4"
Application
•C
ustom units available for frame sizes 31/2" to 10".
Consult factory for availability
• For use on 13/4" thick doors
• All Combination Strike and Stops are packed with
2 x 8-32 machine screws
1/

• Available in brass material polished and plated 26D

No. Base Material

DLS-8 Brass

Specifications
Fasteners
No. of
Inches mm Gauge Holes Machine
5 4"
3/
146.1 .095 6 1/
2 x 8-32
63/4" 171.5 .095 6 1/
2 x 8-32

ElectroLynx® Hinge (QC option)

Each hinge features concealed plug connectors that eliminate the need for separate or
exposed wiring. Standard connectors make installation quick and simple. Brass eyelets add
protection and durability.

• The QC option is available on standard and heavy weight

full mortise bearing hinges as well as swing clear and wide
throw hinges
QC-12
•E
lectric hinges allow a constant flow of current from
the power source through the hinge to electrified
door hardware. No external wires can be seen,
eliminating tampering and improving the aesthetics of
the door opening
• Materials: brass, stainless steel, and steel
• For 4 amp continuous @ 24 volts AC or DC per circuit,
28 gauge multi-strand wires are used.
•A
n 8 position connector is used for QC4 and QC8 wire
hinges. An 8 position and a 4 position connector is used for
QC12 wire hinges.
• Hand of hinge must be specified on two knuckle hinges Application

•C
an be used in conjunction with MM option on most full ElectroLynx
Harness
mortise hinges. QC12 x MM not recommended for wood or (Sold
solid core doors Separately)

•F
ull Mortise QC hinges are available in most BHMA and
McKinney powder coat finishes
•W
ires are coordinated to work with other ASSA ABLOY
Group brands electro-mechanical hardware Female
Male connector
*Electric hinges should be installed in the center position on the
connector
door. Installation instructions are packed with each hinge.
*Hinges are factory tested and specially packaged to minimize Back of 12 wire hinge shown
against damage during shipment.

Options:
Code Description
3-Knuckle 5-Knuckle
QC4 2 circuits
TA314 TA2314
QC8 4 circuits
TA714 TA2714
QC12 6 circuits
TA386 T4A3386
TA786 T4A3786
TA2895
T4A3395 Most hinges including this Swing Clear
Hinge can be electrically modified. Call
T4A3795
1-800-346-7707 for more information.

Steel & Stainless - Approved for NFPA 80

fire rated openings

Standard ElectroLynx® Retrofit Cable Sizes

QC-C1500P Shown

12 Conductor and Molex

Actual Cable 12 Conductor and one end, pinned one
Length Molex both ends end Typical Application
3" QC-C003 QC-C003P
6" QC-C006 QC-C006P Between hinge and the end of an exit device.
12" QC-C012 QC-C012P
26" QC-C200 QC-C200P
32" QC-C206 QC-C206P
Between hinge and through the door to the lockset
38" QC-C300 QC-C300P
or exit device trim.
44" QC-C306 QC-C306P
50" QC-C400 QC-C400P
15' 2" QC-C1500 QC-C1500P
From the hinge location, up the jamb to
25' - QC-C2500P above the ceiling, or up and around full lite
or half lite metal door.
30' - QC-C3000P

Custom lengths available.

MacPro® Electric Hinges

MacPro® Electric Hinges connect the power source to electrified door hardware such as
locking hardware and exit devices. They are ideal for new construction as well as retrofit
and aftermarket applications. The MacPro Electric Hinges feature center exit wires
allowing them to replace existing electric hinges with center exit wires.

• MacPro
Electric Hinges are easy to install with ElectroLynx®
Quick Connect (QC) or Concealed Circuit (CC) connection
options
•O
nce installed, the wires are concealed to increase security
and prevent tampering
• Available in standard and heavy weight
•B
rass eyelets on the portal holes prevent chafing, giving the
hinge an extended service life
• UL Listed
• Concealed Circuit (CC) is available as CC4 or CC8
•E
lectroLynx® Quick Connect (QC) is available with
QC4, QC8 or QC12

Approved for NFPA 80 fire rated openings

Hinge Base
No. Size Gauge Weight Finish Connector Options
Type Material
MPB79 41/2" x 4" Bearing Steel .134 STD 26D CC4, CC8
MPB79 4 2" x 4"
1/
Bearing Steel .134 STD 26D QC4, QC8, QC12
MPB79 4 2" x 4 2"
1/ 1/
Bearing Steel .134 STD 26D CC4, CC8
MPB79 4 2" x 4 2"
1/ 1/
Bearing Steel .134 STD 26D , QC4, QC8, QC12
BSP
MPB68 41/2" x 41/2" Bearing Steel .180 HVY 26D CC4, CC8
MPB68 4 2" x 4 2"
1/ 1/
Bearing Steel .180 HVY 26D QC4, QC8, QC12
MPB91 4 2" x 4
1/
Bearing Stainless .134 STD 32D CC8, QC12
MPB91 4 2" x 4
1/ 1/
2 Bearing Stainless .134 STD 32D CC8, QC12
MPB99 4 2" x 4
1/
Bearing Stainless .180 HVY 32D CC8, QC12
MPB99 41/2" x 41/2 Bearing Stainless .180 HVY 32D CC8, QC12
MPB99 5" x 4½ Bearing Stainless .180 HVY 32D CC8, QC12

•A
llows operation of devices requiring power such as electric CC2-18
locks, electric strikes, and electric latch retraction exit devices
• Wires are contained within the hinge – invisible and
tamperproof
•A
vailable with most two, three, and five knuckle
bearing hinges.
• Available with 4, 8 or 12 wires
• Materials: standard and heavy weight, brass, steel, and
stainless steel
• Four amp continuous @ 24 volts AC or DC per circuit
16.0 Amps intermittent duty (pulse) for 300 milliseconds
• CC option has 28 gauge wire
•C
C-18 option has 2 18 gauge wires and the remainder Application
28 gauge wire. Available 2,4,6,8 and 10 wire
•C
an be used in conjunction with MM option on most full
mortise hinges. CC12 x MM not recommended for wood or
solid core doors
• Optional Mortar guard MG-16 available
• Hinges are supplied with 8" (305) leads as standard.
Extra lengths are available at additional cost
Note: Two knuckle style is handed.

CC-18 Option CC Option

Suffix Suffix Wires Capacity
CC4-18 CC4 4 2 circuits
CC8-18 CC8 8 4 circuits
CC2-18 CC12 12 6 circuits
CC6-18
CC10-18

Approved for NFPA 80 fire rated openings

ElectroLynx® Power over Ethernet (PoE) Hinge

The McKinney ElectroLynx® PoE Quick Connect hinge provides for the passing of Ethernet
data through the door opening. Installation is a snap with the friendly “plug and play”
connectors which allow power to be linked from the incoming source through the door to
the electrified hardware. PoE data is bidirectional.

• Brass eyelets add protection and durability to the PoE PoE Option
hinge which features common wire colors coordinated
to work with intelligent Power over Ethernet
electromechanical hardware from SARGENT and
Corbin Russwin
• The PoE hinge should be installed in the second from
bottom hinge position on the door. Once installed, it
will give no outward indication of its function and will
transfer power and data efficiently and reliably, as long
as the wire capacity is not exceeded
• All PoE hinges are factory tested and specially packaged
to minimize damage during shipment. Installation
U.S. Patent No. 7,824,200
instructions are packed with each hinge. Along with
the PoE hinge, mating PoE door and frame side
Application
harnesses are required to complete the opening. The
required PoE harnesses must be ordered separately
• Specify suffix PoE
Available on:
1/2" and 5" TA2314 & TA2714 Standard Weight 5 Knuckle
4
41/2" and 5" T4A3386 & T4A3786 Heavy Weight 5 Knuckle

Steel & Stainless - Approved for NFPA 80

fire rated openings

Harness Length McKinney Catalog # Door Side Application

30" PoE-C206P 20" to 25" door width (doors with 3 butt hinges with PoE hinge in center to
stile to stile raceway to lock prep).
36" PoE-C300P 26" to 31" door width (doors with 3 butt hinges with PoE hinge in center to
stile to stile raceway to lock prep).
42" PoE-C306P 32" to 36" door width (doors with 3 butt hinges with PoE hinge in center to
stile to stile raceway to lock prep).
48" PoE-C400P 37" to 42" door width (doors with 3 butt hinges with PoE hinge in center to
stile to stile raceway to lock prep).
54" PoE-C406P 43" to 48" door width (doors with 3 butt hinges with PoE hinge in center to
stile to stile raceway to lock prep).
60" PoE-C500P Door Harness Assembly
84" PoE-C700P Door Harness Assembly
156" PoE-C1300P Door Harness Assembly
EPT Harness
360" PoE-CEPT30 EPT Harness Assembly
Frame Side Application
180" PoE-C1500P From the hinge location, up the jamb to wall/ceiling
Custom Lengths Available

800-346-7707 | [Link]
Check the web site for the up-to-date catalog
McKinney is a brand associated with Corbin Russwin, Inc., an ASSA ABLOY Group company. Copyright © 2012-2017, Corbin Russwin, Inc.
EH-4 All rights reserved. Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited.
Electrified Hinges
ElectroLynx® Power over Ethernet (PoE)
Harnesses with RJ-45 Connectors
Connecting ASSA ABLOY Group brands Corbin Russwin and SARGENT next
generation Power over Ethernet (PoE) enabled hardware is quick and easy with new
ElectroLynx® harnesses from McKinney. Molex connectors connect the hinge to the
harness, and a standard RJ-45 connector connects the harness to the electrified door
hardware.
The following hardware uses the RJ-45 connectors:
PoE-C206PRJ Shown
• Corbin Russwin IN220
• Corbin Russwin Access 700 PIP1
• SARGENT IN220
• SARGENT Passport 1000 P1
Harnesses are available with the RJ-45 connector attached or loose in the package.
D-28912
The harnesses range in length from 30" up to 156" with custom lengths available
(consult factory).

ElectroLynx PoE HarnessesD-28912

with RJ-45 Connectors

Actual Cable Molex one end, RJ-45 Molex one end,

Length attached one end D-28908
RJ-45 Loose Door Side Application
30" PoE-C206PRJ PoE-C206RJ 20" to 25" door width (doors with 3 butt hinges with PoE
hinge in center to stile to stile raceway to lock prep).
D-28908
36" PoE-C300PRJ PoE-C300RJ 26" to 31" door width (doors with 3 butt hinges with PoE
hinge in center to stile to stile raceway to lock prep).
42" PoE-C306PRJ PoE-C306RJ 32" to 36" door width (doors with 3 butt hinges with PoE
hinge in center to stile to stile raceway to lock prep).
48" PoE-C400PRJ PoE-C400RJ 37" to 42" door width (doors with 3 butt hinges with PoE
hinge in center to stile to stile raceway to lock prep).
54" PoE-C406PRJ PoE-C406RJ 43" to 48" door width (doors with 3 butt hinges with PoE
hinge in center to stile to stile raceway to lock prep).
Door Harness Assembly
60" PoE-C500PRJ PoE-C500RJ Door Harness Assembly
84" PoE-C700PRJ PoE-C700RJ Door Harness Assembly
156" PoE-C1300PRJ PoE-C1300RJ Door Harness Assembly

EPT Harness Assembly

30 ft cable with loose RJ-45 connector

Actual Cable
Length RJ-45 Loose EPT Harness Assembly
360" PoE-CEPT30RJ EPT Harness Assembly

Magnetic Monitoring Hinge (MM Option)

3500 Series Stainless SteelElectrified

The McKinney Magnetic Monitoring Hinge is the only system on the market that permits field
replacement of magnet and switch. It is a simple, dependable system which defies detection,
yet is readily accessible for inspection and easy adjustment.
•M
M Electric Hinges should be installed in the center position on doors with three hinges or the
second hinge position from the bottom on doors with four hinges
•N
either switch nor operating magnet are attached to the hinge. Non-attachment feature reduces
the chance of damage during installation. Installation instructions packed with each hinge. All MM
Electric Hinges are individually factory pre-tested
•T
he MM feature is available on most two, three and five knuckle full mortise standard and heavy
weight hinges. Consult the individual catalog pages for this option feature

• For low voltage (48 volt maximum) .25 Amps AC or

DC non-inductive load MM Option
• Magnetic reed concealed switch impervious to dirt
and moisture
• Narrow Stile (NS) Switch and Wide Gap Magnet
options available
• Can be used in conjunction with QC option on most
full mortise hinges up to QC12. QC12 x MM not
recommended for wood or solid core doors
• Can be used in conjunction with CC option on most
full mortise hinges up to CC12 Wire. CC12 x MM not
recommended for wood or solid core doors
Front View

UL Listing
6V .25 Amps
12V .25 Amps
24V .125 Amps
48V .062 Amps

Steel & Stainless - Approved for NFPA 80

fire rated openings

Back View

Application

3500 Series Stainless SteelElectrified

• Installs in the door and frame edges
• Accepts a thick cable and protects it within a flexible McK-EPTL, McK-EPT
steel shield
• Device that will work on most doors hung using butt
hinges, continuous hinges or pivots
• Will not function on a center pivot door

Part # Description
McK-EPT Electrical power transfer
McK-EPTL Electrical power transfer, long
McK-EL-EPT ElectroLynx® EPT -12 wire
McK-EL-EPTL ElectroLynx® EPTL -12 wire

Door Cord McK-TSB-C

• Simplest and most economical solution for
power transfer
• Consists of an 18" or 36" armored stainless steel
cable and plastic end pieces in light gray and black
• Cable has an interior diameter of .25"
• Supports interior wire cables up to .2"

Part # Description
McK-TSB-C Door cord with gray/black caps
18" cord
McK-TSB-CXL Door cord with gray/black caps
36" cord

Electrified Hinge Service Kit

The service kit includes a quantity of every different type of connector and terminal required
for repairing product connections/terminations or pinning wires on certain retrofit harnesses.
Contains 10 each 2, 4, 8 Molex receptacles and plugs as well as corresponding terminals,
extraction tool and pinning assembly guide.

QC-R001
Part # Description
QC-R001 Service Kit Locking mechanism

Female Male plug

receptacle (8 circuit)
Receptacles and Terminals
(8 circuit)
Quantity Part # Description
1 bag (100 pc) QC-RF2 Female receptacle (2ckt)
1 bag (100 pc) QC-RF4 Female receptacle (4ckt)
1 bag (100 pc) QC-RF8 Female receptacle (8ckt)
1 bag (100 pc) QC-RM2 Male plug (2ckt) Female receptacle Male plug requires
requires female terminal male terminal
1 bag (100 pc) QC-RM4 Male plug (4ckt)
1 bag (100 pc) QC-RM8 Male plug (8ckt)
1 bag (100 pc) QC-FT2024 Female terminal (AWG 20-24)
1 bag (100 pc) QC-FT2630 Female terminal (AWG 26-30)
1 bag (100 pc) QC-MT2024 Male terminal (AWG 20-24) The plug and receptacle connectors are designed to
mate and lock together as shown in the figure. Plug the
1 bag (100 pc) QC-MT2630 Male terminal (AWG 26-30)
connectors onto each other with the locking mechanism
1 bag (100 pc) POE-MT2024 Male Terminal (AWG 20-24) aligned as indicated.

1 bag (100 pc) POE-RM6 Male Plug

1 bag (100 pc) POE-RF6 Female Plug
1 bag (100 pc) POE-MT2630 Male Terminal
1 bag (100 pc) POE-FT2630 Female Terminal
1 bag (10 pc) QC-DCC Pinning assembly guide

Molex Hand Crimp Tool

The crimp tool is required for adding Molex terminals (connector pins) to wires used with
ElectroLynx® products. The tool is intended for low volume, or repair requirements only.

QC-R003
Part # Description
QC-R003 Molex Hand Crimp Tool

QC-R002
Part # Description
QC-R002 Extraction Tool

Junction Box For Electric Hinges

Recommended for use with our Concealed Circuit Hinges to protect wires. Unit to be
installed in middle hinge location.

• Knock-out holes on both ends for wires to pass through MG-16

• Removable cover plate from end brackets
• Guard supplied assembled for use with electric hinges
• Fits hinge reinforcements for 41/2" or 5" contract
grade hinges
• 20 gauge galvanized sheet steel, furnished in 2C finish

Part # Description
MG-16 Junction Box

StormPro® Tornado Resistant Hinges

Built to withstand the extreme wind speeds and flying debris associated with severe
weather conditions.

• McKinney StormPro® hinges are part of the integrated unit SP3386

when used with StormPro® tornado resistant assemblies
from Ceco Door and CURRIES, along with other StormPro® SP3786
hardware by ASSA ABLOY Group brands
• ASSA ABLOY StormPro® Assemblies Meet UL Certification for
Fire, ICC 500-2014 and FEMA Guidelines
• Use for the common flush door/frame/wall application
• Fire rated thru 3 hours
• Packed with stainless steel machine screws
Application

No. ANSI Cross Reference Base Material Weight

SP3386 A5111 Stainless HVY
SP3786 A8111 Steel HVY

Specifications
Fasteners
No. of Options:
Inches mm Gauge Holes Machine
Code Description
41/2" x 41/2" 114.3 x 114.3 .180 8 1/
2 x 12-24
NRP Non-Removable Pin
41/2" x 5" 114.3 x 127 .180 8 1/
2 x 12-24
QC ElectroLynx® Hinge 4,
4 2" x 6"
1/
114.3 x 152.4 .180 8 1/
2 x 12-24 8, 12 wire available on
hinges up to 6" wide
4 2" x 7"
1/
114.3 x 177.8 .180 8 1/
2 x 12-24
4 2" x 8"
1/
114.3 x 203.2 .180 8 1/
2 x 12-24
5" x 4 2"
1/
127 x 114.3 .190 8 1/
2 x 12-24
5" x 5" 127 x 127 .190 8 1/
2 x 12-24
5" x 6" 127 x 152.4 .190 8 1/
2 x 12-24
5" x 7" 127 x 177.8 .190 8 1/
2 x 12-24
5" x 8" 127 x 203.2 .190 8 1/
2 x 12-24

Approved for NFPA 80 fire rated openings

• The Full Mortise Pocket Pivot Hinge is designed to give

a flush appearance to the corridor when the door is
PH-4
open and recessed into a pocket in the corridor wall
• For single and cross corridor doors, the PH-4 allows
the door to lay against the wall with no projection into
the opening and no gap between the door and frame
• When combined with a floor closer, this application has
minimum visible hardware and clearances
• The PH-4 Full Mortise Pocket Pivot Hinge meets
material and performance requirements of NFPA-80
and ANSI A-156-1
• Meets or exceeds ANSI A117.1 – 1986
Application
Providing Accessibility and Usability for Physically
Handicapped People
• Investment cast steel base material (Finish - 26D)
• Two thrust bearings for vertical loads
• Roller bearing for lateral support
• Listed for both hollow metal or steel covered
composite fire doors rated up to 3 hours
• Listed for wood core type fire doors rated 20 minutes
• Non-handed

Specifications
Fasteners
No. of
No. Base Material Gauge Holes Machine Wood
PH-4 Cast Steel .187 10 3/
4 x 12-24 11/4 x 12

Specifications
Door Weight (Lbs.) Door Width # Hinges/Door
150 3'0" x 7'0" 2
250 3'0" x 7'0" 3
350 4'0" x 7'0" 4

Meets or exceeds
Recommended for applications where Swing Clear Hinges are aesthetically ANSI A117.1 - 1986
unacceptable and use of the full width of the corridor is required, such as cross Providing Accessibility
corridor and smoke and fire doors as well as patient room doors. and Usability for Physically
Handicapped People

Approved for NFPA 80 fire rated openings

Raised Barrel Full Mortise Standard and Heavy Weight Hinges

3500 Series Stainless SteelSpecialty

Raised Barrel Hinges are recommended for use where the door is set in a deep reveal.

•S
tandard weight raised barrel hinges are recommended
for use on average frequency and/or medium weight wood RB-TA2314
or metal doors where the door is set in a deep revealed
frame RB-TA2714
• Standard weight raised barrel hinges are supplied with
a no hole bottom plug and the pin is held in place by an
NRP set screw which allows the hinge to be reversible.
Specify RB-TA4714/RB-TA4314 for doors beveled on
hinge side
•H
eavy weight raised barrel hinges are recommended for
use on high frequency and/or heavy wood or metal doors Square Edge
where the door is set in a deep revealed frame Application

• Heavy weight raised barrel hinges are supplied with

a no hole bottom plug and the pin is held in place by an
NRP set screw which allows the hinge to be reversible.
Specify RB-T4A4786/RB-T4A4386 for doors beveled
on hinge side
• Door leaf mortised into door
• Frame leaf may be mortised or surface applied
• Reversible Hinge
Beveled Edge
Application

No. Base Material Weight

RB-TA2714 Steel STD
RB-TA2314 Stainless Steel STD
RB-T4A3786 Steel HVY
RB-T4A3386 Stainless Steel HVY

Specifications
Fasteners
No. of
Inches mm Gauge Holes Machine Wood
41/2" x 41/2" 114.3 x 114.3 .134 8 1/
2 x 12-24 11/4 x 12
41/2" x 41/2" 114.3 x 114.3 .180 8 1/
2 x 12-24 11/4 x 12
5" x 41/2" 127.0 x 114.3 .190 8 1/
2 x 12-24 11/4 x 12

Approved for NFPA 80 fire rated openings

3500 Series Stainless SteelSpecialty

Recommended for use on average frequency and/or medium weight aluminum doors
with aluminum frames in schools, hospitals and other public buildings where medium
traffic is experienced.

Type 1
Type 1:
• One leaf has standard punching and countersinking
and the other leaf is drilled and tapped so it can be
inserted through a slot in the door or frame. Both
leaves are specially swaged to provide 3/16" clearance
between leaves when parallel
•H
inges are handed - Indicate hand when ordering.
LH shown, RH opposite
Type 2 Type 2:
• Both leaves are drilled and tapped so they can be
inserted through a slot in the door and frame. Both
leaves are specially swaged to provide 5/16" clearance
between the leaves when parallel
• Hinges are non-handed

No. Base Material Weight Type 1

Application
TA2314 Type 1 Stainless Steel STD
TA2714 Type 1 Steel STD
TA2314 Type 2 Stainless Steel STD
TA2714 Type 2 Steel STD

Specifications
Fasteners
No. of
Inches mm Gauge Holes Machine Wood Type 2
4" x 4" Type 1 101.6 x 101.6 .130 8 1/
2 x 12-24 11/4 x 12 Application

41/2" x 4" Type 1 124.3 x 101.6 .134 8 1/

2 x 12-24 11/4 x 12
41/2" x 41/2" Type 1 124.3 x 124.3 .134 8 1/
2 x 12-24 11/4 x 12

Fastener
No. of
Inches mm Gauge Holes Machine
4" x 4" Type 2 101.6 x 101.6 .130 8 1/
2 x 12-24
41/2" x 4" Type 2 124.3 x 101.6 .134 8 1/
2 x 12-24
Options:
41/2" x 41/2" Type 2 124.3 x 124.3 .134 8 1/
2 x 12-24
Code Description
NRP Non-Removable Pin

Approved for NFPA 80 fire rated openings

Full Mortise Interim Hinges

Recommended for installations where door and frame are prepped for two
different size hinges.

• For new or retrofit installations

TA2714
• An equal amount is trimmed from the top and bottom Interim
of the leaf
• Interim hinges are supplied with a no hole bottom plug
and the pin is held in place by an NRP set screw which
allows the hinge to be reversible
•A
vailable in both standard (TA2714; TA2314) and heavy
weight (T4A3786; T4A3386)
• For finishes see page 28

No. Base Material Weight

TA2714 Interim Steel STD
TA2314 Interim Stainless Steel STD
T4A3786 Interim Steel HVY
T4A3386 Interim Stainless Steel HVY

Specifications
Fasteners
No. of
Door Leaf Jamb Leaf Gauge Holes Machine Wood
5" 4 2"*
1/
.146 STD 8 1/
2 x 12-24 11/4 x 12
41/2"* 5" .146 STD 8 1/
2 x 12-24 11/4 x 12

Specifications
Fasteners
No. of
Door Leaf Jamb Leaf Gauge Holes Machine Wood
5" 4 2"*
1/
.190 HVY 8 1/
2 x 12-24 11/4 x 12
41/2"* 5" .190 HVY 8 1/
2 x 12-24 11/4 x 12

*Trimmed to height

Approved for NFPA 80 fire rated openings

Available Styles Specifications

T2895 Inches mm Gauge No. of Fasteners

Size Finish Corners Holes Wood Residential Swing
3 /2 "
1
US4 1
/4 " RC 31/2" 88.9 0.086 6 1 x10 Clear Hinge
4" 101.6 0.123 8 11/4 x 12
31/2" US4 5
/8 " RC T2895
31/2" US15 1
/4 " RC
31/2" US15 5
/8 " RC
3 /2 "
1
10BE 1
/4 " RC
31/2" 10BE 5
/8 " RC
4" US4 1
/4 " RC
4" US15 1
/4 " RC
4" 10BE 1
⁄4 " RC Door opening with a Door opening with a
regular hinge swing clear hinge

RediFrame Swing Clear Hinge

Designed specifically for RediFrame and Timely door frames.

Available Styles Specifications

TA2895 & TA4895 Inches mm Gauge No. of Fasteners

Size Finish Corners Holes Rediframe Swing
4 /2 "
1
26D SC 41/2" 114.3 0.134 8 Metal and Clear Hinge
Wood
TA2895

Residential Spring Hinges

Designed for light weight, self-closing doors.
Used as an alternative to door closing devices, this hinge is made of residential grade material making
it a perfect fit for multi-family housing and similar applications. Generally two spring hinges must be
used in order to provide the force needed to close the door.
The 31/2" hinge is available as the 1552 stainless steel version or the 1502 steel hinge which is offered
in a variety of finishes.

Part number Description Finish

155880 31/2 x 31/2 1502 3
31/2 x 31/2
155881 3 /2 x 3 /2 1502
1 1
4
155882 31/2 x 31/2 1502 10 1502
155883 3 /2 x 3 /2 1502
1 1
10A
155884 31/2 x 31/2 1502 10B
155884E 31/2 x 31/2 1502 10BE
155885 3 /2 x 3 /2 1502
1 1
15
155886 31/2 x 31/2 1502 26
155887 3 /2 x 3 /2 1502
1 1
26D
155888 31/2 x 31/2 1502 BSP
155889 31/2 x 31/2 1502 P
155890 3 /2 x 3 /2 1552
1 1
32D

Specifications
Inches mm Gauge No. of Fasteners Fasteners
Holes Wood Metal
31/2" x 31/2" 88.9 x 88.9 .106 6 #10 x 11/4" #10-24 x ½"

Residential Hinges
4x4
For light weight doors.
1400
For Multi-family and residential applications. Rounded or square corners.
Consult the factory for availability of other finishes.

Part number Description Finish Corners

56689 31/2 x 31/2 1400 4 Square
56868 31/2 x 31/2 1458 26D 5
/8 " radius
56869 31/2 x 31/2 1458 BSP 5
/8 " radius
31/2 x 31/2
56870 31/2 x 31/2 1458 3 5
/8 " radius 1414
56288 3 /2 x 3 /2 1400
1 1
26D Square
56281 31/2 x 31/2 1414 26D 1
/4 " radius
56748 4 x 4 1400 26D Square

31/2 x 31/2
1458

• Interior or exterior hollow metal and wood frame doors

• 13/4" thick doors
• Used with square edge doors only
• Bearing contains anti-friction component
• Cannot be electrified
• SQ314 only:
• UL Listed for both hollow metal or steel covered
composite fire doors rated up to 3 hours SQ3331
• UL Listed for wood core fire doors rated 20 minutes Two Knuckle

No. Base Material Handing Weight

SQ3331 Two Knuckle Brass Handed Special
SQ314 Three Knuckle Stainless Steel Non-Handed Special

Approved for NFPA 80 fire rated openings

Specifications
Fasteners
No. of
Inches mm Gauge Holes Machine Wood
SQ314
4 2" x 4 2"
1/ 1/
114.3 x 114.3 .177 8 1/
2 x 12-24 11/4 x 12
41/2" x 4* 114.3 x 101.6 .177 8 1/
2 x 12-24 11/4 x 12
Three Knuckle
*Size not offered for SQ3331

SQ3331 Finishes
03 – Bright Brass, Clear Coated
10B – Dark Oxidized Satin Bronze, Oil Rubbed
10BE – Dark Oxidized Satin Bronze, Equivalent
14 – Bright Nickel, Clear Coated
15 – Satin Nickel, Clear Coated
26 – Bright Chrome
26D – Satin Chrome
BSP – Black Suede Powder Coat

SQ314 Finish
32D – Satin Stainless Steel

Note: Other finishes may be available upon request

Decorative Hinges – Olive Knuckle

3500 Series Stainless SteelSpecialty

Recommended for use on interior or exterior hollow metal and wood frame doors.

• Interior or exterior hollow metal and wood frame doors

TA3383
• 13/8" to 13/4" thick doors
• Meets grade 2 cycle testing
• Bearing contains anti-friction component
• Specify right or left hand when ordering
• Cannot be electrified

No. Base Material Weight

TA3383 Olive Knuckle Brass LT

Specifications
Fasteners
No. of
Inches mm Gauge Holes Machine Wood
6" x 37/8" 152.4 x 98.4 .203 8 1/
2 x 12-24 11/4 x 12

Width of Leaves 13/16" (20.6mm)

Finishes
03 – Bright Brass, Clear Coated
03NL – Bright Brass, No Lacquer
10B – Dark Oxidized Satin Bronze, Oil Rubbed
10BE – Dark Oxidized Satin Bronze, Equivalent
14 – Bright Nickel, Clear Coated
15 – Satin Nickel, Clear Coated
26 – Bright Chrome
26D – Satin Chrome

Concealed
• Base material: Zinc alloy • Opening angle: 180° Satin Stainless Steel (MK80SS only)
• Non-handed • 3-dimensional adjustability
Matte Black
Matte White (MK80A and MK100 only)

3500 Series Stainless Steel

Model No. Of
Inches mm Metal Wood
Model Holes Additional finishes on request
MK40A 41/2" x 7/8" 115mm x 23mm 4 M5 x 20 screws 35mm PHWS
MK80 43/8" x 11/8" 111.5mm x 29mm 4 M5 x 20 screws 35mm PHWS
MK80A 43/8" x 11/8" 111.5mm x 29mm 4 M5 x 20 screws 35mm PHWS
MK80SS 43/8" x 11/8" 111.5mm x 29mm 4 M5 x 20 screws 35mm PHWS
MK100 61/4" x 11/16" 160mm x 28mm 8 M5 x 20 screws 35mm PHWS

MK40A Series
• Covers included • Base material: Zinc alloy
• Door thickness minimum: 11/4"
Note: When installing with a door closer at least 3 hinges are required,
and reduce maximum door weight in chart by 30%.

Hinge Capacity
Number of Door Width
Hinges 32" 36" 42" 48"
2 92 lbs 88 lbs 72 lbs 66 lbs
3 105 lbs 99 lbs 81 lbs 74 lbs
4 116 lbs 110 lbs 86 lbs 76 lbs
MK40A
MK80/MK80A/MK80SS Series
•M K80 - no covers, MK80A - covers • Base material:
included , MK80SS - Stainless Steel - – MK80/MK80A - Zinc alloy
no covers – MK80SS - Stainless Steel
• Door thickness minimum: 13/8"
Note: When installing with a door closer at least 3 hinges are required,
and reduce maximum door weight in chart by 30%.

Hinge Capacity
Number of Door Width
Hinges 32" 36" 42" 48"
2 185 lbs 176 lbs 143 lbs 132 lbs
3 211 lbs 198 lbs 160 lbs 149 lbs
4 233 lbs 220 lbs 171 lbs 158 lbs

MK100/MK100ME Series MK80 MK80A MK80SS

• Covers included • MK100ME available MK80SS approved for NFPA80 fire rated openings
• Door thickness minimum: 13/8" in Satin Chrome and
• Base material: Zinc alloy Matte Black only
• MK100ME available
in CC12 and QC12
configurations
Note: When installing with a door closer at least 3 hinges are required,
and reduce maximum door weight in chart by 30%.

Hinge Capacity
Number of Door Width
Hinges 32" 36" 42" 48"
2 224 lbs 220 lbs 180 lbs 165 lbs
3 253 lbs 246 lbs 202 lbs 185 lbs MK100 MK100ME
4 282 lbs 275 lbs 216 lbs 198 lbs

Concealed Hinges Finishes

For use on wood or hollow metal doors with wood or metal frames. Satin Chrome
Concealed

• Base material: Zinc alloy • Opening angle: 180°

• Non-handed • 3-dimensional adjustability
3500 Series Stainless Steel

Model No. Of
Inches mm Metal Wood
Model Holes
MK150 7 7/8" x 11/4" 200mm x 32mm 8 M5 x 20 screws 35mm PHWS
MK200 10 /4" x 1 /8"
1 3
260mm x 36mm 8 M5 x 20 screws 35mm PHWS

MK150 Series
• Magnetic covers included
• Door thickness minimum: 11/2"

Note: When installing with a door closer at least 3 hinges are required,
and reduce maximum door weight in chart by 30%.

Hinge Capacity
Number of Door Width
Hinges 32" 36" 38" 42" 48"
2 366 lbs 326 lbs 313 lbs 280 lbs 245 lbs MK150 Series
3 412 lbs 367 lbs 352 lbs 315 lbs 275 lbs
4 457 lbs 408 lbs 391 lbs 350 lbs 306 lbs

MK200 Series
• Magnetic covers included
• Door thickness minimum: 13/4"

Note: When installing with a door closer at least 3 hinges are required,
and reduce maximum door weight in chart by 30%.

Hinge Capacity
Number of Door Width
Hinges 32" 36" 38" 42" 48"
2 487 lbs 434 lbs 417 lbs 373 lbs 326 lbs
3 548 lbs 489 lbs 469 lbs 419 lbs 367 lbs
4 609 lbs 543 lbs 521 lbs 466 lbs 408 lbs

MK200 Series

• 4 models for standard and heavy weight metal doors

• 304 Stainless Steel Material, 32D Finish
• Handed- specify right (RH) or left handed (LH) when ordering
• Clearance - Minimum clearance at head of frame is 3/16". For doors greater
than 1-3/4" clearance is 1/4"

No. Of Lift (180° Door Rating Cam Lift Hinge (RH)

Model Size Fasteners Thickness
Holes Opening) (112⁄ Pairs) MKCL134
MKCL134 41/2" x 41/2" 12-24 x 34⁄ " 8 3
⁄"
16 up to 200 lbs .134
MKCL180 5" x 4 ⁄ "
1
2 12-24 x ⁄ " 3
4 8 1
⁄"
4 up to 300 lbs .180
MKCL250 5" x 4 ⁄ "
1
2 12-24 x ⁄ " 3
4 8 5
⁄"
16 up to 500 lbs .25
MKCL2500 5" x 412⁄ " 5
⁄ -18 x 34⁄ "
16 8 5
⁄"
16 up to 900 lbs .25

Approved for NFPA80 fire rated openings

Cam Lift Hinge (LH)

MKCL180

Notes
Notes

Notes

McKinney is a product line of ASSA ABLOY Accessories and Door Controls Group, Inc., an ASSA ABLOY Group company.
Copyright © 2020-2023, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in part
without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited. Printed in the U.S.A. 51510 5306 1/23

MPB68 Heavy Weight Hinge Specifications
No ratings yet
MPB68 Heavy Weight Hinge Specifications
1 page
McKinney Full Mortise Hinge Catalog
No ratings yet
McKinney Full Mortise Hinge Catalog
1 page
Hinge Catalog
100% (1)
Hinge Catalog
168 pages
McKinney 2013 Price Book
No ratings yet
McKinney 2013 Price Book
208 pages
McKinney 2014 Price Book
No ratings yet
McKinney 2014 Price Book
192 pages
Ives Architectural Hardware Overview
No ratings yet
Ives Architectural Hardware Overview
3 pages
Ives 5bb1hwtw
No ratings yet
Ives 5bb1hwtw
2 pages
Monroe Hinge Manufacturing Overview
No ratings yet
Monroe Hinge Manufacturing Overview
9 pages
SGS Hardware Catalog #12 Overview
No ratings yet
SGS Hardware Catalog #12 Overview
39 pages
Types of Hinges and Their Applications
100% (1)
Types of Hinges and Their Applications
13 pages
Hinge Installation & Maintenance Guide
No ratings yet
Hinge Installation & Maintenance Guide
2 pages
Essential Guide to Door Hinges
No ratings yet
Essential Guide to Door Hinges
6 pages
DHFMS Hinge Types and Specifications
No ratings yet
DHFMS Hinge Types and Specifications
102 pages
UL Listed Stainless Steel Hinges
No ratings yet
UL Listed Stainless Steel Hinges
18 pages
Door Hinge Quotation - Hafele Philippines
No ratings yet
Door Hinge Quotation - Hafele Philippines
3 pages
Jolly Hardware Price List 2024
No ratings yet
Jolly Hardware Price List 2024
60 pages
Jamison Door Swing Door Parts List
No ratings yet
Jamison Door Swing Door Parts List
85 pages
ASSA ABLOY Hinge Selection Guide
No ratings yet
ASSA ABLOY Hinge Selection Guide
6 pages
Hinge Types and Selection Guide
No ratings yet
Hinge Types and Selection Guide
7 pages
Hager Door Hardware 2016 Catalog
No ratings yet
Hager Door Hardware 2016 Catalog
656 pages
Select Hinges Price Book - 2015
No ratings yet
Select Hinges Price Book - 2015
16 pages
Disadvantages of Piano Hinges Explained
No ratings yet
Disadvantages of Piano Hinges Explained
22 pages
ASSA ABLOY Door Hinges Overview
No ratings yet
ASSA ABLOY Door Hinges Overview
11 pages
Hinge Specification Guide
No ratings yet
Hinge Specification Guide
4 pages
MODUL Hinge System Overview
No ratings yet
MODUL Hinge System Overview
24 pages
High-Performance Butt Hinges Overview
No ratings yet
High-Performance Butt Hinges Overview
4 pages
Ansi - Bhma-A156.1-2006
100% (1)
Ansi - Bhma-A156.1-2006
25 pages
Albert-Einstein-Strasse 42a, D-63322 Roedermark, Germany Tel.: 0049 (0) 6074-7286503 - Fax: 0049 (0) 6074-7286504
100% (1)
Albert-Einstein-Strasse 42a, D-63322 Roedermark, Germany Tel.: 0049 (0) 6074-7286503 - Fax: 0049 (0) 6074-7286504
19 pages
Stainless Steel Hinges and Mortice Locks
No ratings yet
Stainless Steel Hinges and Mortice Locks
80 pages
Key and Cylinder Marking Guide
No ratings yet
Key and Cylinder Marking Guide
51 pages
JCP Price List 2019 PDF
No ratings yet
JCP Price List 2019 PDF
76 pages
Joinery Hardware Overview and Types
No ratings yet
Joinery Hardware Overview and Types
159 pages
Architectural Hardware Price List 2021
No ratings yet
Architectural Hardware Price List 2021
53 pages
Hettich Hinges: Types and Technology
No ratings yet
Hettich Hinges: Types and Technology
23 pages
Ficha Técnica Bisagras Certf. Ul
0% (1)
Ficha Técnica Bisagras Certf. Ul
3 pages
Flat Hinges Product Index Guide
No ratings yet
Flat Hinges Product Index Guide
34 pages
Austin Hardware Catalog PDF
0% (1)
Austin Hardware Catalog PDF
284 pages
Topic 13 - Building Hardwares
No ratings yet
Topic 13 - Building Hardwares
12 pages
DoorHinge - D&DHARDWARE20 Nuevo
No ratings yet
DoorHinge - D&DHARDWARE20 Nuevo
2 pages
Mac Tools Catalog No 14 1947
No ratings yet
Mac Tools Catalog No 14 1947
40 pages
Concealed Hinges Product Overview
No ratings yet
Concealed Hinges Product Overview
169 pages
Kinlong Door Control Hardware Catalogue
No ratings yet
Kinlong Door Control Hardware Catalogue
160 pages
Essential Hinges for DIY Projects
No ratings yet
Essential Hinges for DIY Projects
13 pages
Pneumatic Hinges for Folding Doors
No ratings yet
Pneumatic Hinges for Folding Doors
10 pages
TM 5-805-8 - Builders' Hardware
No ratings yet
TM 5-805-8 - Builders' Hardware
16 pages
Screw-On Hinges Product Overview
No ratings yet
Screw-On Hinges Product Overview
49 pages
MODEL 1332 MODEL 1432: Slide Length
No ratings yet
MODEL 1332 MODEL 1432: Slide Length
8 pages
Types of Hinges Overview
No ratings yet
Types of Hinges Overview
7 pages
Dekkson Stainless Steel Catalog
No ratings yet
Dekkson Stainless Steel Catalog
16 pages
Types of Cabinet Hardware Explained
No ratings yet
Types of Cabinet Hardware Explained
11 pages
Datasheet 0
No ratings yet
Datasheet 0
46 pages
Hinge Types - A Modern Overview
100% (1)
Hinge Types - A Modern Overview
9 pages
Comprehensive Guide to Door Hardware
No ratings yet
Comprehensive Guide to Door Hardware
31 pages
Hettich PDF
No ratings yet
Hettich PDF
164 pages
50x50 Screw-On Hinge with Grounding
No ratings yet
50x50 Screw-On Hinge with Grounding
2 pages
Hettich Price List 2025 PDF Download
No ratings yet
Hettich Price List 2025 PDF Download
208 pages
Building a Braiding Business from Home
No ratings yet
Building a Braiding Business from Home
1 page
E-Commerce, Its Core Concepts
No ratings yet
E-Commerce, Its Core Concepts
8 pages
Amazon's E-Commerce Dominance Analysis
No ratings yet
Amazon's E-Commerce Dominance Analysis
8 pages
Ecommerce Website Report
100% (1)
Ecommerce Website Report
40 pages
Positive Impacts of E-Commerce on Society
No ratings yet
Positive Impacts of E-Commerce on Society
5 pages
Augmented Reality's Impact on Impulse Buying
No ratings yet
Augmented Reality's Impact on Impulse Buying
13 pages
E-Commerce Project for B.Com Honours
No ratings yet
E-Commerce Project for B.Com Honours
45 pages
International Sponsoring Guide
100% (1)
International Sponsoring Guide
246 pages
Factors Influencing Online Brand Trust: Evidence From Online Buyers in Kathmandu Valley
No ratings yet
Factors Influencing Online Brand Trust: Evidence From Online Buyers in Kathmandu Valley
18 pages
Online Bookstore System Design Assignment
No ratings yet
Online Bookstore System Design Assignment
2 pages
Digital Customer Behavior Insights
No ratings yet
Digital Customer Behavior Insights
24 pages
E-Commerce Project Report Overview
No ratings yet
E-Commerce Project Report Overview
52 pages
E-Commerce Management Insights
No ratings yet
E-Commerce Management Insights
7 pages
How To Use Ecwid To Make An Online Store On Facebook Page - Jayvee Cochingco - The Virtual Master
No ratings yet
How To Use Ecwid To Make An Online Store On Facebook Page - Jayvee Cochingco - The Virtual Master
118 pages
Digital Transformation Plan for Artisan Store
No ratings yet
Digital Transformation Plan for Artisan Store
21 pages
Digital Transaction Awareness Report
No ratings yet
Digital Transaction Awareness Report
41 pages
Debate on Cyber Bullying Laws
No ratings yet
Debate on Cyber Bullying Laws
8 pages
Future of Work in Africa: Tech Insights
No ratings yet
Future of Work in Africa: Tech Insights
20 pages
Shopee App Redesign Insights
No ratings yet
Shopee App Redesign Insights
1 page
E-Shopping Cart Micro-Project Report
No ratings yet
E-Shopping Cart Micro-Project Report
12 pages
TikTok Shop: Social Commerce Insights
No ratings yet
TikTok Shop: Social Commerce Insights
9 pages
Mercadona's Strategic Marketing Insights
No ratings yet
Mercadona's Strategic Marketing Insights
9 pages
Analyzing Bezos' Leadership in Amazon
No ratings yet
Analyzing Bezos' Leadership in Amazon
4 pages
Consumer Insights on Disease Prevention
No ratings yet
Consumer Insights on Disease Prevention
27 pages
Speaking Topics for Personal Experiences
No ratings yet
Speaking Topics for Personal Experiences
25 pages
Exam Tips for English Comprehension
No ratings yet
Exam Tips for English Comprehension
13 pages
Consumer Behavior in E-Shopping
No ratings yet
Consumer Behavior in E-Shopping
37 pages
Impact of Electronic Communication on Business
No ratings yet
Impact of Electronic Communication on Business
11 pages
Online Buying Behavior in Kuwait MBA Thesis
No ratings yet
Online Buying Behavior in Kuwait MBA Thesis
73 pages
Search's Impact on In-Store Purchases
No ratings yet
Search's Impact on In-Store Purchases
9 pages