CeraBest Silver

CERAMIC ADHESIVE

SMART ADVANTAGES
- Easy to use
- Plastic consistency
- Horizontally and vertically

PRODUCT DESCRIPTION
CeraBest Silver is a C1T class, water and humidity
resistant, cement-based adhesive mortar that produced
in accordance with EN 12004. It is used for the adhesion of
finishing materials such as ceramic, glazed tile, and mosaic
on the floor and walls.

APPLICATION AREAS
- Indoors and outdoors
- On walls and floors
- Horizontally and vertically TECHNICAL DATA
- Used for adhering chinaware, ceramic, porous and non-
porous ceramic plates, key-stone, etc. all kinds of stone, Colour Grey
concrete and stone derivative plates.
Dry Unit Volume Weight (kg / lt) 1,5 ± 0,2
FEATURES Wet Unit Volume Weight (kg / lt) 1,5 ± 0,2
- Resistant to water and humidity
- Durable Pot Life (min) 60 - 120
- Plastic consistency, easy-to-apply Working Time (min) 20 - 30
- Does not slip vertically
- Hydraulic bonding quality Curing time (hour) ~ 24
- Fireproof
Bonding Strength (28 days) ≥ 0,5 (N / mm²)
PREPARATION OF THE SUBSTRATE Slip ≤ 0,5
- Foreign substances that prevent adhesion such as dust,
dirt, form oil, scoria, paint and other residues and wastes Mixing Water Ratio (for 25 kg
such as cement, plaster and concrete should be removed 5,5 ~ 6,5 lt
mortar)
from the surface of application.
- The sub-surfaces that are not strong enough to bear their Environment temperature for
Between +5°C and +35°C
own weight e.g. cracked plasters, weak surfaces, or residues application
of moss should be cleaned from the application surface. Between -25°C and
- The floors which require repair should be levelled with Resistance of hardened coating
+80°C
self-levelling surface screeds minimum 3-4 days before
adhesive application. Technical data is obtained according to +23°C air
- Using primer is recommended on anhydrous and highly temperature and 50% relative humidity.
absorptive surfaces such as aerated and exposed concrete.
AFTER APPLICATION
APPLICATION
In the initial days, freshly filled joints should be protected
- Bostik CeraBest Silver Ceramic Adhesive in powder form
from direct sunlight, strong air stream, high air temperature
should be mixed in low cycle after pouring into a container
(above +35°C), rain and frost.
filled with some clean water at normal environment
temperature until a smooth mixture is obtained. Mixing
COVERAGE
time should be minimum 5 minutes. The obtained mortar
Approximately 1,5 - 3,0 kg/m².
should be rested for 3 minutes and mixed for 2 minutes until
Consumption amounts are theoretical values and we
it becomes homogenous.
recommend that consumption controlled sample
- The prepared mortar is spread on the surface with a
application is carried out before application.
toothed comb having suitable tooth size.
- Finishing materials (ceramic, tiles, etc) should be adhered
PACKAGE
on the combed mortar within 15 minutes. If this period of
In 25 kg craft bags, 64 bags in 1 palette (1600 kg/pallet)
time is exceeded, the mortar should be scraped off from the
plates and fresh mortar should be spread.
STORAGE
- The finishing materials should be adhered and fitted well
- Dry mortar bags should be protected from water, frost
with a rubber beater by controlling the flatness of the
and adverse air conditions.
surface.
- They should be kept dry and cool on wooden pallets at
- Minimum 24 hours should be waited for joint filler
between +10°C and +25°C in moisture free conditions.
application.
- The torn and opened products should be closed
immediately and consumed first.

1/2
- Maximum 8 bags should be stocked on each other.
- Shelf life is maximum 12 months conditional to complying
with the above mentioned storage conditions.

HEALTH AND SAFETY INFORMATION

EN
12004
C1 T

8
Lt
5 20

BOSTIK SMART SUPPORT

Smart help
+971 4 875 1700
Date: 24.09.2018 – Rev:000

Bostik Consumer & Construction

Warning: Bostik is only responsible for the product quality and cannot be held responsible for its mis-use except for the recommendations regarding where and/or how the product shall be used. It is not possible
to give a guarantee for the results of operations for individual cases, due to multiplicity of possible uses and storage and processing conditions of the product, which are not under our control. Where necessary,
the user should make their own tests. Due to local regulations, product performance may vary from country to country. This technical bulletin hereby is valid until it is renewed. BOSTIK’s right to amend the
products in accordance with technical developments is reserved. In cases concerning the safety of the products, the material safety data sheet (SDS) containing this information should be consulted.

2/2