AV RECEIVER

RX-A3020/RX-V3073 SERVICE MANUAL

Note: When the DIGITAL P.C.B. or IC78 on DIGITAL P.C.B. is replaced, this unit will display “Internal Error”
and will not operate at all without additional setting.
In such a case, report the serial number of this unit to the following e-mail address.
Yamaha Corporation will reply providing the setting procedure to make this unit operate properly.
注意：DIGITAL P.C.B. または DIGITAL P.C.B. の IC78 を交換すると Internal Error が表示されて本機が正常に動作し
なくなり、本機が正常に動作するための追加設定が必要になります。
そのような場合には本機のシリアルナンバーを下記の E メールアドレスへご連絡ください。
折り返し、本機が正常に動作するための追加設定の方法をご連絡します。
E-mail: [email protected]

RX-A3020/RX-V3073
IMPORTANT NOTICE
This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.
It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already known
and understood by the users, and have therefore not been restated.
WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury,
destruction of expensive components, and failure of the product to perform as specified. For these reasons, we advise
all YAMAHA product owners that any service required should be performed by an authorized YAMAHA Retailer or
the appointed service representative.
IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or
recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.
The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service
departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable and
specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the
distributor's Service Division.
WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have
accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).
IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.

■ CONTENTS
TO SERVICE PERSONNEL ............................................2 DISPLAY DATA .......................................................82–84
FRONT PANELS .............................................................3 IC DATA ................................................................. 85–105
REAR PANELS ...........................................................4–7 BLOCK DIAGRAMS ............................................ 106–109
REMOTE CONTROL PANEL ..........................................8 PRINTED CIRCUIT BOARDS ..............................110–137
SPECIFICATIONS / 参考仕様 ................................... 9–16 PIN CONNECTION DIAGRAMS ................................. 138
INTERNAL VIEW .......................................................... 17 SCHEMATIC DIAGRAMS ................................... 139–158
SERVICE PRECAUTIONS / サービス時の注意事項 ..... 17 REPLACEMENT PARTS LIST ............................ 159–190
DISASSEMBLY PROCEDURES / 分解手順 ........... 18–21 REMOTE CONTROL ........................................... 191–193
UPDATING FIRMWARE / CONFIGURING THE SYSTEM SETTINGS ................. 194
ファームウェアのアップデート ............................22–24 システム設定を変更する ..................................... 195–196
SELF-DIAGNOSTIC FUNCTION / FIRMWARE UPDATING PROCEDURE .............. 197–208
ダイアグ（自己診断機能）.....................................25–79 ファームウェア更新手順 ..................................... 209–214
POWER AMPLIFIER ADJUSTMENT /
パワーアンプ調整 .................................................80–81

Copyright © 2012 All rights reserved.

101245 This manual is copyrighted by YAMAHA and may not be copied or
redistributed either in print or electronically without permission.
P.O.Box 1, Hamamatsu, Japan
'12.09
 RX-A3020/RX-V3073

■ TO SERVICE PERSONNEL AC LEAKAGE

1. Critical Components Information WALL EQUIPMENT TESTER OR
Components having special characteristics are marked and OUTLET UNDER TEST EQUIVALENT
must be replaced with parts having specifications equal to those
originally installed.
2. Leakage Current Measurement (For 120V Models Only)
When service has been completed, it is imperative to verify
INSULATING
that all exposed conductive surfaces are properly insulated TABLE
from supply circuits.
• Meter impedance should be equivalent to 1500 ohms shunted • Leakage current must not exceed 0.5mA.
by 0.15 μF. • Be sure to test for leakage with the AC plug in both polarities.

For U model
“CAUTION”
“F2002: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 10A,
125V FUSE.”
For C model
CAUTION
F2002: REPLACE WITH SAME TYPE 10A, 125V FUSE.
ATTENTION
F2002: UTILISER UN FUSIBLE DE RECHANGE DE MÉME TYPE DE 10A, 125V.
RX-A3020/RX-V3073

WARNING: CHEMICAL CONTENT NOTICE!

This product contains chemicals known to the State of California to cause cancer, or birth defects or other reproductive
harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON
WHATSOEVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or
expose eyes to solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands before
handling food.

About lead free solder / 無鉛ハンダについて

All of the P.C.B.s installed in this unit and solder joints are 本機に搭載されているすべての基板およびハンダ付けに
soldered using the lead free solder. よる接合部は無鉛ハンダでハンダ付けされています。
Among some types of lead free solder currently available, 無鉛ハンダにはいくつかの種類がありますが、修理時に
it is recommended to use one of the following types for は下記のような無鉛ハンダの使用を推奨します。
the repair work. Sn+Ag+Cu（錫 + 銀 + 銅）
• Sn + Ag + Cu (tin + silver + copper) Sn+Cu（錫 + 銅）
• Sn + Cu (tin + copper) Sn+Zn+Bi（錫 + 亜鉛 + ビスマス）
• Sn + Zn + Bi (tin + zinc + bismuth)
注意：
Caution: 無鉛ハンダの融点温度は通常の鉛入りハンダに比べ 30 ∼
As the melting point temperature of the lead free solder 40℃程度高くなっていますので、それぞれのハンダに合っ
is about 30°C to 40°C (50°F to 70°F) higher than that of たハンダごてをご使用ください。
the lead solder, be sure to use a soldering iron suitable
to each solder.

2
 RX-A3020/RX-V3073

■ FRONT PANELS
RX-A3020 (U, C, R, T, K, A, B, G, F, L, S, J models)

U model

C, R, T, K, A, B, G, F, L, S models

J model

RX-A3020/RX-V3073
RX-V3073 (T, A models)

3
 RX-A3020/RX-V3073

■ REAR PANELS
RX-A3020 (U model)

RX-A3020 (C model)
RX-A3020/RX-V3073

RX-A3020 (R, S models)

4
 RX-A3020/RX-V3073

RX-A3020 (T model)

RX-A3020 (K model)

RX-A3020/RX-V3073
RX-A3020 (A model)

5
 RX-A3020/RX-V3073

RX-A3020 (B, G, F models)

RX-A3020 (L model)
RX-A3020/RX-V3073

RX-A3020 (J model)

6
 RX-A3020/RX-V3073

RX-V3073 (T model)

RX-V3073 (A model)

RX-A3020/RX-V3073

7
 RX-A3020/RX-V3073

■ REMOTE CONTROL PANEL

RAV420
RX-A3020/RX-V3073

Inside of the remote control cover

リモコンカバー内部

8
 RX-A3020/RX-V3073

■ SPECIFICATIONS / 参考仕様
■ Audio Section / オーディオ部

Rated Output Power (Power Amp. Section) / Input Sensitivity/Input Impedance / 入力感度／入力インピーダンス
定格出力（パワーアンプ部） (1 kHz, 100 W/8 ohms)
(1 kHz, 0.9 % THD) PHONO (MM) .................................................... 3.5 mV / 47 k-ohms
– 1 channel driven – AUDIO 2, etc. ................................................... 200 mV / 47 k-ohms
U, C, R, T, K, A, B, G, F, L, S models (8 ohms) Maximum Input Signal / 最大許容入力 (1 kHz, 0.5 % THD)
FRONT L/R ................................................................ 185 W/ch
PHONO (MM) ............................................................60 mV or more
CENTER .......................................................................... 185 W
SURROUND L/R ........................................................ 185 W/ch AUDIO 2, etc. ..............................................................2.4 V or more
SURROUND BACK L/R ............................................. 185 W/ch
Output Level/Output Impedance / 出力電圧／出力インピーダンス
FRONT PRESENCE L/R ............................................. 185 W/ch
AV OUT ............................................................ 200 mV / 1.2 k-ohms
B, G, F models (4 ohms)
FRONT L/R ................................................................ 230 W/ch HEADPHONE OUT ............................................ 150 mV / 100 ohms

J model (6 ohms) PRE OUT

FRONT L/R ................................................................ 200 W/ch 1 kHz .................................................................... 1 V / 1.2 k-ohms
CENTER .......................................................................... 200 W 50 Hz (SUBWOOFER) .......................................... 1 V / 1.2 k-ohms
SURROUND L/R ........................................................ 200 W/ch ZONE OUT .............................................................. 1 V / 1.2 k-ohms
SURROUND BACK L/R ............................................. 200 W/ch
Frequency Response / 再生周波数帯域 (10 Hz to 100 kHz)
FRONT PRESENCE L/R ............................................. 200 W/ch
AUDIO 2, etc. (Pure Direct) .................................................0 / -3 dB
– 2 channels driven simultaneously –
RIAA Equalization Deviation / RIAA 偏差 (1 kHz, 50 mV, 8 ohms)
U, C, R, T, K, A, B, G, F, L, S models (8 ohms)
PHONO (MM) ................................................................... 0 ±0.5 dB
FRONT L/R .......................................................165 W + 165 W

RX-A3020/RX-V3073
CENTER .......................................................................... 165 W Total Harmonic Distortion / 全高調波歪率 (20 Hz to 20 kHz)
SURROUND L/R ...............................................165 W + 165 W
PHONO (MM) to AV OUT ............................................0.02 % or less
SURROUND BACK L/R ....................................165 W + 165 W
FRONT PRESENCE L/R ....................................165 W + 165 W Multi channel input (Pure Direct) to SP OUT (70 W/8 ohms)
.................................................................................0.04 % or less
(20 Hz to 20 kHz, 0.06 % THD)
– 2 channels driven simultaneously – Signal to Noise Ratio / 信号対雑音比 (IHF-A network)

U, C, R, T, K, A, B, G, F, L, S models (8 ohms) PHONO (MM) to AV OUT

FRONT L/R .......................................................150 W + 150 W U, C, R, T, S models (Input shorted 5 mV) .............. 86 dB or more
CENTER .......................................................................... 150 W K, A, B, G, F, L models (Input shorted 5 mV) .......... 81 dB or more
SURROUND L/R ...............................................150 W + 150 W J model (Input shorted 2.5 mV) ................................ 80 dB or less
SURROUND BACK L/R ....................................150 W + 150 W AUDIO 2, etc. (Pure Direct) to SP OUT (Input shorted 250 mV)
FRONT PRESENCE L/R ....................................150 W + 150 W .............................................................................. 100 dB or more
J model (6 ohms) Residual Noise / 残留ノイズ (IHF-A Network)
FRONT L/R .......................................................150 W + 150 W FRONT L/R to SP OUT ................................................150 μV or less
CENTER .......................................................................... 150 W
SURROUND L/R ...............................................150 W + 150 W Channel Separation / チャンネルセパレーション (1 kHz / 10 kHz)
SURROUND BACK L/R ....................................150 W + 150 W PHONO (MM) (Input shorted)
FRONT PRESENCE L/R ....................................150 W + 150 W ...................................................... 60 dB or more / 55 dB or more
Maximum Effective Output Power / 実用最大出力 (JEITA) AUDIO 2, etc. (Input 5.1 k-ohms shorted)
(1 channel driven / 1 kHz, 10 % THD) [R, T, K, L, S, J models] ...................................................... 60 dB or more / 45 dB or more
R, T, K, L, S models (8 ohms) Volume Control Range/Step / 音量可変範囲／ステップ
FRONT L/R ...................................................................... 230 W/ch Main ZONE, ZONE 2, ZONE 3
CENTER ............................................................................... 230 W ...................................... MUTE / -80 dB to +16.5 dB / 0.5 dB step
SURROUND L/R .............................................................. 230 W/ch
SURROUND BACK L/R ................................................... 230 W/ch Tone Control Characteristics / トーンコントロール特性
FRONT PRESENCE L/R .................................................. 230 W/ch Main ZONE
J model (6 ohms) Bass
FRONT L/R ...................................................................... 230 W/ch Boost/Cut ...................................... ±6 dB / 0.5 dB step, at 50 Hz
CENTER ............................................................................... 230 W Turnover frequency .......................................................... 350 Hz
SURROUND L/R .............................................................. 230 W/ch Treble
SURROUND BACK L/R ................................................... 230 W/ch Boost/Cut .....................................±6 dB / 0.5 dB step, at 20 kHz
FRONT PRESENCE L/R .................................................. 230 W/ch Turnover frequency ......................................................... 3.5 kHz

Dynamic Power Per Channel (IHF) ZONE 2, ZONE 3

U, C, R, T, K, A, B, G, F, L, S models Bass
Boost/Cut ....................................... ±10 dB / 2 dB step, at 50 Hz
FRONT L/R (1 channel driven)
Turnover frequency .......................................................... 350 Hz
(8 / 6 / 4 / 2 ohms) ..................................... 175 / 220 / 295 / 410 W
Treble
Damping Factor / ダンピングファクタ (1 kHz, 8 ohms) Boost/Cut ....................................... ±10 dB / 2 dB step, at 50 Hz
FRONT L/R to SPEAKER-A ............................................ 150 or more Turnover frequency ......................................................... 3.5 kHz

9
 RX-A3020/RX-V3073

Bass Crossover Frequency / 低域クロスオーバー周波数 Signal to Noise Ratio / 信号対雑音比 (IHF)

FRONT, CENTER, SURROUND, SURROUND BACK small (H.P.F.) U model
.................... fc=40/60/80/90/100/110/120/160/200 Hz, 12 dB/oct. HD Radio ...............................................................................80 dB
SUBWOOFER small (L.P.F.) C, R, T, K, A, B, G, F, L, S, J models
.................... fc=40/60/80/90/100/110/120/160/200 Hz, 24 dB/oct. Mono / Stereo ........................................................... 72 dB / 70 dB

Optical Jack, Coaxial Jack Support Frequencies / Harmonic Distortion / 歪率 (1 kHz)

Optical 端子、Coaxial 端子 対応 fs U model
............................................................................... 32 kHz to 96 kHz HD Radio ............................................................................. 0.03 %
C, R, T, K, A, B, G, F, L, S, J models
■ Video Section / ビデオ部 Mono / Stereo ............................................................ 0.3 % / 0.5 %

Video Signal Type / ビデオ信号方式 Antenna Input / アンテナ入力

....................................................................... 75 ohms unbalanced
Monitor / ZONE out (Wall paper / GUI) /
モニター ／ ZONE アウト（壁紙 ／ GUI）
U, C, R, K, S, J models ................................................NTSC / PAL ■ AM Section / AM 部
T, A, B, G, F, L models ..................................................PAL / NTSC
Tuning Range / 受信周波数範囲
Video conversion / GUI / ビデオコンバージョン ／ GUI
.....................................................................................NTSC / PAL U, C models ........................................................... 530 to 1,710 kHz
R, L, S models ......................... 530 to 1,710 kHz / 531 to 1,611 kHz
Video Signal Level / ビデオ信号レベル
T, K, A, B, G, F, J models ....................................... 531 to 1,611 kHz
Composite Video Signal / コンポジットビデオ信号
RX-A3020/RX-V3073

............................................................................1 Vp-p / 75 ohms Antenna / アンテナ

S-Video Signal / S ビデオ信号 ..................................................................................... Loop antenna
Y ..........................................................................1 Vp-p / 75 ohms
C ■ General / 総合
U, C, R, K, S, J models (NTSC) .................0.286 Vp-p / 75 ohms
Power Supply / 電源電圧
T, A, B, G, F, L models (PAL) .........................0.3 Vp-p / 75 ohms
U, C models ............................................................ AC 120 V, 60 Hz
Component Video Signal / コンポーネントビデオ信号
R, S models .................................AC 110–120/220–240 V, 50/60 Hz
Y ..........................................................................1 Vp-p / 75 ohms
T model ................................................................... AC 220 V, 50 Hz
Pb/Pr ................................................................0.7 Vp-p / 75 ohms
K model .................................................................. AC 220 V, 60 Hz
D4 Video Signal / D4 ビデオ信号 [J model]
A model .................................................................. AC 240 V, 50 Hz
Y ..........................................................................1 Vp-p / 75 ohms
B, G, F models ........................................................ AC 230 V, 50 Hz
Pb/Pr ................................................................0.7 Vp-p / 75 ohms
L model ...................................................... AC 220–240 V, 50/60 Hz
Video Maximum Input Level / ビデオ最大許容入力
J model .............................................................. AC 100 V, 50/60 Hz
(VIDEO Conversion Off)
............................................................................... 1.5 Vp-p or more Voltage Selector [R, S models]
...........................................................110–120 V / 220–240 V select
Video Signal to Noise Ratio / ビデオ信号対雑音比
(VIDEO Conversion Off) Power Consumption / 消費電力
................................................................................... 60 dB or more
U model ....................................................................490 W / 620 VA
Monitor/ZONE Out Frequency Response / C model ....................................................................400 W / 510 VA
モニター／ ZONE 出力周波数帯域
R, T, A, B, G, F, L, S models .................................................... 490 W
(VIDEO Conversion Off)
K model .................................................................................. 390 W
Component video signal / コンポーネントビデオ信号
.................................................................5 Hz to 100 MHz, ±3 dB J model ................................................................................... 280 W

D4 video signal / D4 ビデオ信号 [J model] Standby Power Consumption (reference data) /

.................................................................5 Hz to 100 MHz, ±3 dB 待機時消費電力（参考値）
HDMI control: OFF / Standby through: OFF
■ FM Section / FM 部 ................................................................................ 0.3 W (typical)
HDMI control: ON / Standby through: ON
Tuning Range / 受信周波数範囲 ................................................................................ 6.0 W (typical)
U, C models ......................................................... 87.5 to 107.9 MHz HDMI control: OFF / Standby through: ON
R, L, S models .................87.5 to 108.0 MHz / 87.50 to 108.00 MHz INPUT: AV 1 (HDMI no signal)
T, K, A, B, G, F models .................................... 87.50 to 108.00 MHz ............................................................................. 5.0 W (typical)

J model .................................................................. 76.0 to 90.0 MHz Network standby: ON

................................................................................ 2.2 W (typical)
50 dB Quieting Sensitivity / 50 dB SN 感度 (IHF)
(1 kHz, 100 % MOD.) Maximum Power Consumption [R, L, S models]
Mono ......................................................................... 3 μV (20.8 dBf) (10 % THD, All channel driven)
............................................................................................. 1,210 W

10
 RX-A3020/RX-V3073

Dimensions (W x H x D) / 寸法（幅 × 高さ × 奥行き）

[RX-A3020]
............................ 435 x 192 x 467 mm (17-1/8" x 7-1/2" x 18-3/8") DTS-HD, the Symbol, & DTS-HD and the Symbol together are registered
trademarks & DTS-HD Master Audio is a trademark of DTS, Inc. Product
[RX-V3073] includes software. © DTS, Inc. All Rights Reserved.
............................ 435 x 182 x 465 mm (17-1/8" x 7-1/8" x 18-3/8")
DTS-HD および記号は DTS 社の登録商標です。また、DTS-HD Master Audio は
Weight / 質量 DTS 社の商標です。製品にはソフトウェアを含みます。著作権 DTS 社。不許複製。

[RX-A3020]
U, C, R, K, A, L, S models ................................. 18.2 kg (40.1 lbs.)
T, B, G, F, J models ........................................... 19.9 kg (43.9 lbs.)
AirPlay, the AirPlay logo, iPad, iPhone, iPod, iPod nano, and iPod touch are
[RX-V3073]
trademarks of Apple Inc., registered in the U.S. and other countries.
T model ............................................................. 19.5 kg (43.0 lbs.) AirPlay、AirPlay ロ ゴ、iPad、iPhone、iPod、iPod nano、iPod touch は、 米 国
A model ............................................................. 17.8 kg (39.2 lbs.) およびその他の国々で登録されている Apple Inc. の商標です。

Finish / 仕上げ
[RX-A3020]
T, J models .....................................................................Gold color
U, C, R, T, K, A, B, G, F, L, S, J models ........................ Black color
R, B, G, F, L, J models .............................................Titanium color
MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and
[RX-V3073] Thomson.

RX-A3020/RX-V3073
T model ..........................................................................Gold color MPEG Layer 3 音声圧縮技術は Fraunhofer IIS および Thomson によってライセン
T, A models .................................................................. Black color ス供与されています。

Accessories / 付属品
Remote control ..............................................................................x 1
Battery (AAA, UM-4) .....................................................................x 4
FM antenna (1.4 m) ......................................................................x 1
This receiver supports network connections.
AM antenna (1.2 m) (U model) .....................................................x 1
本機はネットワーク接続に対応しています。
(1.0 m) (C, R, T, K, A, B, G, F, L, S, J models) ..........x 1
YPAO microphone (6.0 m) ............................................................x 1
Microphone base ..........................................................................x 1
Power cable (U, C, R, T, K, A, B, G, F, S, J models) ....................x 1 HD Radio Technology manufactured under license from iBiquity Digital
(L model) .................................................................x 2 Corporation. U.S. and Foreign Patents. HD Radio™ and the HD, HD Radio,
and “Arc” logos are proprietary trademarks of iBiquity Digital Corp.

* Specifications are subject to change without notice.

※ 参考仕様および外観は、製品の改良のため予告なく変更すること
があります。 “HDMI,” the “HDMI” logo and “High-Definition Multimedia Interface” are
trademarks, or registered trademarks of HDMI Licensing LLC.
U .......................U.S.A. model B ......................British model
HDMI、HDMI ロゴ、および High-Definition Multimedia Interface は、HDMI
C .................Canadian model G .................European model
Licensing, LLC の商標または登録商標です。
R ....................General model F .................... Russian model
T .................... Chinese model L .................Singapore model
K ..................... Korean model S .................. Brazilian model
A ................Australian model J .................. Japanese model
“x.v.Color” is a trademark of Sony Corporation.
「x.v.Color」は、ソニー株式会社の商標です。

“SILENT CINEMA” is a trademark of Yamaha Corporation.

「サイレントシネマ ™ SILENT CINEMA ™」はヤマハ株式会社の登録商標です。

Manufactured under license from Dolby Laboratories. Dolby, Pro Logic and
the double-D symbol are trademarks of Dolby Laboratories.
ドルビーラボラトリーズからの実施権に基づき製造されています。「ドルビー」 、
「Pro Logic」およびダブル D 記号 はドルビーラボラトリーズの商標です。 DLNA™ and DLNA CERTIFIED™ are trademarks or registered trademarks
of Digital Living Network Alliance. All rights reserved. Unauthorized use is
strictly prohibited.
DLNA はデジタルリビングネットワークアライアンスの米国およびその他の国
における登録商標です。無断使用は固く禁じられています。

11
 RX-A3020/RX-V3073

This product incorporates copyright protection technology that is protected Windows is a registered trademark of Microsoft Corporation in the United
by U.S. patents and other intellectual property rights. Use of this copyright States and other countries.
protection technology must be authorized by Rovi Corporation, and is
Windows は米国 Microsoft Corporation の米国およびその他の国における登録商
intended for home and other limited viewing uses only unless otherwise
標です。
authorized by Rovi Corporation. Reverse engineering or disassembly is
prohibited.
Rovi Corporation。
Windows XP, Windows Vista, Windows 7, Windows Media Audio and
Windows Media Player are either registered trademarks or trademarks of
Microsoft Corporation in the United States and/or other countries.
Windows XP、Windows Vista、Windows 7、Windows Media Audio、Windows
Media Connect、Windows Media player は、米国 Microsoft Corporation の米
国およびその他の国における登録商標、または商標です。

AAC ロゴマーク はドルビーラボラトリーズの商標です。

• DIMENSIONS / 寸法図
RX-A3020/RX-V3073

RX-A3020 RX-V3073
Top view Top view
(2-3/8")

(2-3/8")
(1")

(1")
27

25
ø 60 ø 60
62

62
298 (11-3/4")

298 (11-3/4")
418 (16-1/2")
467 (18-3/8")

418 (16-1/2")
465 (18-1/4")
ø 48/18
58
(2-1/4")

58
(2-1/4")

50 335 (13-1/4") 50 335 (13-1/4")

22
(7/8")

22
(7/8")

(2") (2")

Front view Front view

171 (6-3/4")

161 (6-3/8")
192 (7-1/2")

182 (7-1/8")
21
(7/8")

21
(7/8")

435 (17-1/8") 435 (17-1/8")

Unit: mm (inch) Unit: mm (inch)

単位：mm（インチ） 単位：mm（インチ）

12
 RX-A3020/RX-V3073

• SELECT MENU
Sound field parameters

Surround Back Initial Delay: 1 to 49 ms

Surround Back Room Size: 0.1 to 2.0

Surround Initial Delay: 1 to 49 ms

Surround Back Liveness: 0 to 10

Parameter

Front/Rear Balance: -5 to +5, [0]

Surround Room Size: 0.1 to 2.0

Left/Right Balance: -5 to +5, [0]

Monaural Mix: Off / On, [Off]

Height Balance: 0 to 10, [5]
Surround Liveness: 0 to 10
DSP Level: -6 to +3 dB, [0]

Reverb Delay: 0 to 250 ms

Reverb Level: 0 to 100 %

Reverb Time: 1.0 to 5.0 s
Initial Delay: 1 to 99 ms

Direct: Auto / Off, [Auto]

Room Size: 0.1 to 2.0

Level: -5 to +5, [0]

Decode Type (*1)

Liveness: 0 to 10

Reset
Category Program
MOVIE THEATER Standard ● ● ● ● ● ● ● ● ●
Spectacle ● ● ● ● ● ● ● ● ●
Sci-Fi ● ● ● ● ● ● ● ● ●
Adventure ● ● ● ● ● ● ● ● ●
Drama ● ● ● ● ● ● ● ● ●
Mono Movie ● ● ● ● ● ● ● ●

RX-A3020/RX-V3073
ENTERTAINMENT Sports ● ● ● ● ● ● ● ●
Action Game ● ● ● ● ● ● ● ●
Roleplaying Game ● ● ● ● ● ● ● ●
Music Video ● ● ● ● ● ● ● ●
Recital/Opera ● ● ● ● ● ● ● ●
CLASSICAL Hall in Munich ● ● ● ● ●
Hall in Vienna ● ● ● ● ●
Hall in Amsterdam ● ● ● ● ●
Church in Freiburg ● ● ● ● ● ● ●
Church in Royaumont ● ● ● ● ● ● ●
Chamber ● ● ● ● ● ● ●
LIVE/CLUB Village Vanguard ● ● ● ● ●
Warehouse Loft ● ● ● ● ● ● ● ●
Cellar Club ● ● ● ● ●
The Roxy Theatre ● ● ● ● ● ● ● ●
The Bottom Line ● ● ● ● ●
STEREO 2ch Stereo ● ●
9ch Stereo ● ● ● ● ● ●
SUR. DECODE SURROUND DECODER ● ●
*1
STRAIGHT

*1 Surround Decoder Panorama Center Width Dimension Center Image

Off / On, [Off] 0 to 7, [3] -3 to +3, [0] 0.0 to 1.0, [0.3]
Pro Logic
PL IIx Movie / PL II Movie
PL IIx Music / ● ● ●
Decode Type PL II Music
PL IIx Game / PL II Game
Neo:6 Cinema
Neo:6 Music ●

13
 RX-A3020/RX-V3073

• SET MENU TABLE / セットメニュー

MAIN MENU SUB-MENU PARAMETER VALUE [INITIAL VALUE]

Speaker Auto Measure Optimizes the speaker configuration automatically using YPAO.

Setup Multi Position Yes / No

Result Not Available

Manual Setting Pattern [Pattern1] / Pattern2 * Select “ENTER”

Setting Data Copy Pattern1 2 / Pattern2 1 * Select “ENTER”

Power Amp Assign [Basic] / 7ch +1ZONE / 9ch +1ZONE / 7ch +2ZONE /
7ch +FRONT +1ZONE / 5ch +FRONT +2ZONE / 7ch BI-AMP

* Select “ENTER”

EXTRA SP 1 / 2 Zone 2 / Zone 3

* When “Power Amp Assign” is set to “Basic / 7ch BI-AMP”, this

setup is disabled.

Configuration Front Large / [Small]

* When “Subwoofer1/2” is set to “None”, “Front” is disabled.

Center
Large / [Small] / None
Surround
RX-A3020/RX-V3073

Surround Back Large x1 / Large x2 / Small x1 / [Small x2] / None

* When “Surround” is set to “None”, “Surround Back” is disabled.

Crossover 40 / 60 / [80] / 90 / 100 / 110 / 120 / 160 / 200 Hz

* When “Front / Center / Surround / Surround Back” is set to

“Small”, this setup is enabled.

Front Presence [Use] / None

Rear Presence Use / [None]

Subwoofer 1, Subwoofer 2 [Use] / None

Select “Use” [Normal] / Reverse

SWFR Layout Left + Right / Front + Rear / [Monaural x2]

* When “Subwoofer1/2” is set to “None”, “SWFR Layout” is disabled.

Extra Bass [Off] / On

* When “Front” is set to “Large”, “Extra Bass” is disabled.

Distance Meter / Feet

Front L, Front R,

Center,

Surround L, Surround R,
0.30 to 24.00 m, [3.00 m], 0.05 m step
Surround Back L, Surround Back R,
1.0 to 80.0 ft, [10.0 ft], 0.2 ft step
Front Presence L, Front Presence R,

Rear Presence L, Rear Presence R,

Subwoofer 1, Subwoofer 2

Level Front L, Front R,

Center,

Surround L, Surround R,

Surround Back L, Surround Back R, -10.0 to +10.0 dB, [0.0 dB], 0.5 dB step

Front Presence L, Front Presence R,

Rear Presence L, Rear Presence R,

Subwoofer 1, Subwoofer 2

14
 RX-A3020/RX-V3073

MAIN MENU SUB-MENU PARAMETER VALUE [INITIAL VALUE]

Speaker Manual Parametric EQ Manual / YPAO : Flat / YPAO : Front / YPAO : Natural / [Through]

Setup * Select “ENTER”

Front L, Front R, Band ▶ Band: #1 to #7

Center, / Gain ▲ Gain: -20.0 to +6.0 dB, [0.0 dB], 0.5 dB step

Surround L, Surround R,

Surround Back L,

Surround Back R, Frequency ▶ Frequency: 31.3 Hz to 16.0 kHz, [62.5 Hz]

Front Presence L, / Gain ▲ Gain: -20.0 to +6.0 dB, [0.0 dB], 0.5 dB step

Front Presence R,

Rear Presence L,

Rear Presence R, Q ▶ Q: 0.500 to 10.080, [1.000]

Subwoofer 1, / Gain ▲ Gain: -20.0 to +6.0 dB, [0.0 dB], 0.5 dB step

Subwoofer 2

* When “Parametric EQ” is set to “Through”, this setup is enabled.

RX-A3020/RX-V3073
PEQ Data Copy Flat Manual / Front Manual / Natural Manual

* When “Parametric EQ” is set to “Manual”, “PEQ Data Copy” is

enabled.

PEQ Data Clear OK / CANCEL

* When “Parametric EQ” is set to “Manual”, “PEQ Data Clear” is

enabled.

Test Tone [Off] / On

Sound Setup Lipsync Delay Enable AV 1 / AV 2 / AV 3 / AV 4 / AV 5 / AV 6 / AV 7 / Disable / [Enable]

AUDIO 1 / AUDIO 2 / AUDIO 3 / AUDIO 4

Auto/Manual Select [Auto] / Manual

Adjustment 0 to 500 ms, [0 ms], 1 ms step

Dynamic Range [Maximum] / Standard / Minimum/Auto

Max. Volume -30.0 to +16.5 dB (Maximum volume), [+16.5 dB], 5.0 dB step

Initial Volume [Off] / On

Select “On” Mute, -80 to +16.5 dB, [-40.0 dB], 0.5 dB step

Pure Direct Mode [Auto] / Video Off

Adaptive DSP Level Off / [On]

Video Setup Analog to Analog Conversion Off / [On]

Video Mode [Direct] / Processing

Select Resolution Through / [Auto] / 576p / 720p / 1080i / 1080p / 4K

“Processing” * Select “ENTER”

Aspect [Through] / 16:9 Normal / Smart Zoom

Adjustment Preset Contrast Enhancement

1 Resolution Enhancement [Off] / Auto

Noise Reduction (NR)

to
Brightness

Preset Contrast -100 to +100, [0], 1 step

6 Saturation

HDMI Setup HDMI Control [Off] / On

Select “On” TV Audio Input [AUDIO 1] / AUDIO 2 / AUDIO 3 / AUDIO 4

ARC (Audio Return Channel) Off / [On]

Standby Sync Off / On / [Auto]

15
 RX-A3020/RX-V3073

MAIN MENU SUB-MENU PARAMETER VALUE [INITIAL VALUE]

HDMI Setup Audio Output Amp Off / [On]

HDMI OUT 1, HDMI OUT 2 [Off] / On

Standby Through [Off] / On

* When HDMI Control is set to “On”, “Standby Through” is disabled.

Network IP Address DHCP Off / [On]

Setup IP Address xxx.xxx.xxx. x

Subnet Mask xxx.xxx.xxx. x

Default Gateway xxx.xxx.xxx. x

DNS Server (P) Primary x. x. x. x

DNS Server (S) Secondary x. x. x. x

Network Standby [Off] / On

MAC Address Filter [Off] / On

Filter MAC Address 1–5, 6–10 xx : xx : xx : xx : xx : xx

Network Name Input is possible to 15 characters

Multi Zone Main Zone Set Zone Rename Input is possible to 9 characters
RX-A3020/RX-V3073

Setup Zone 2, Zone 3 Volume Fixed / [Variable]

Set Max. Volume -30.0 to +16.5 dB (Maximum volume), [+16.5 dB], 5.0dB step

Initial Volume [Off] / On

Select “On” Mute, -80 to +16.5 dB, 0.5 dB step

Mono [Off] / On

Zone Scene Rename SCENE1–4 Input is possible to 20 characters

Zone Rename Input is possible to 9 characters

Zone 4 Set Zone Scene Rename SCENE1–4 Input is possible to 20 characters

Zone Rename Input is possible to 9 characters

Monitor Out Assign [Main] / Zone 2 / Zone 3

HDMI OUT2 Assign [Main] / Zone 2 (Audio Output: Off) / Zone 4

Party Mode Set Target: Zone 2, Target: Zone 3, Target: Zone 4 Disable / [Enable]

Function Input Assignment Coaxial ①,②,⑥ None /

Setup Optical ③,④,⑤ AV 1 / AV 2 / AV 3 / AV 4 / AV 5 / AV 6 / AV 7 /

Component , , , AUDIO 1 / AUDIO 2 / AUDIO 3 / AUDIO 4 * Select “ENTER”

Display Set Dimmer (Front Display) -4 to 0 (higher to brighten), [0]

Short Message [On] / Off

Wall Paper Picture1 / Picture2 / Picture3 / Gray

Trigger Trigger Mode [Power] / Source / Manual

Output1 Select “Source” AV 1–7, V-AUX, AUDIO 1–4, PHONO, TUNER, AirPlay,

SERVER, NET RADIO, USB, MULTI CH

Trigger Low / [High]

Output2 Select “Manual” Low / [High]

Target Zone Main / Zone 2 / Zone 3 / [All]

Memory Guard [Off] / On

ECO Setup Auto Power Down Off / 2 Hours / 4 Hours / 8 Hours / 12 Hours

U, C, R, T, K, A, L, J models: [Off]

B, G, F models: [8 Hours]

ECO Mode [Off] / On

Language [English (English)] / 日本語 (Japanese) / Français (French) /

Setup Deutsch (German) / Español (Spanish) / Рyccкий (Russian) /

中文 (Chinese) * Select “ENTER”

16
 RX-A3020/RX-V3073

■ INTERNAL VIEW
Rear view 1 2
1 VIDEO (1) P.C.B.
2 AMPPOWER (3) P.C.B. (R, S models)
3 AMPPOWER (2) P.C.B.
4 AMP (3) P.C.B.
5 HD RADIO TUNER (U model)
AM/FM TUNER (C, R, T, K, A, B, G, F, L, S, J models)
6 FUNCTION (2) P.C.B.
7 6 5 4 3 7 FUNCTION (1) P.C.B.
8 9 10 11 12 8 POWER P.C.B.
9 DIGITAL (3) P.C.B.
Top view
10 AMPPOWER (1) P.C.B.
11 DIGITAL (1) P.C.B.
12 DAC P.C.B.
13 AMP (2) P.C.B.
14 AMPPOWER (5) P.C.B.
15 AMP (5) P.C.B.
16 POWER TRANSFORMER
17 VIDEO (3) P.C.B.
18 AMP (4) P.C.B.
19 AMPPOWER (4) P.C.B.

RX-A3020/RX-V3073
20 AMP (1) P.C.B.
21 OPERATION (1) P.C.B.
22 OPERATION (3) P.C.B.
23 DIGITAL (2) P.C.B.
24 OPERATION (2) P.C.B.
25 OPERATION (4) P.C.B.
20 19 18 17 16 15 14 13

Front view 21 22

25 24 23

■ SERVICE PRECAUTIONS / サービス時の注意事項

Safety measures 安全対策
• Some internal parts in this product contain high voltages ・ この製品の内部には高電圧部分があり危険です。修理
and are dangerous. の際は、絶縁性の手袋を使用するなどの安全対策を
Be sure to take safety measures during servicing, such 行ってください。
as wearing insulating gloves.
• Note that the capacitors indicated below are dangerous ・ 下記のコンデンサには電源を OFF にした後も電荷が残
even after the power is turned off because an electric り、高電圧が維持されており危険です。
charge remains and a high voltage continues to exist 修理作業前に放電用抵抗（5 k Ω /10 W）を下記の各コ
there. ンデンサの端子間に接続して放電してください。
Before starting any repair work, connect a discharging 放電所用時間は各々約 30 秒間です。
resistor (5 k-ohms/10 W) to the terminals of each AMPPOWER（1）P.C.B. の C1822 ∼ C1828
capacitor indicated below to discharge electricity.
POWER P.C.B. の C2016
The time required for discharging is about 30 seconds
per each. 詳しくは PRINTED CIRCUIT BOARDS を参照してくだ
さい。
C1822–C1828 on AMPPOWER (1) P.C.B.
C2016 on POWER P.C.B.
For details, refer to “PRINTED CIRCUIT BOARDS”. 17
 RX-A3020/RX-V3073

■ DISASSEMBLY PROCEDURES / 分解手順

(Remove parts in the order as numbered.) （番号順に部品を外してください。）
Disconnect the power cable from the AC outlet. AC 電源コンセントから、電源コードを抜いてください。

1. Removal of Top Cover 1. トップカバーの外し方

a. Remove 4 screws (①), 4 screws (②) and 2 screws (③). a. ① のネジ 4 本、② のネジ 4 本、③ のネジ 2 本を外し
(Fig. 1) ます。（Fig. 1）
b. Lift the rear of the top cover to remove it. (Fig. 1) b. トップカバーの後部を持ち上げて外します。 （Fig. 1）

2. Removal of Front Panel Unit 2. フロントパネルユニットと

and Sub-chassis Unit サブシャーシユニットの外し方
a. Remove 6 screws (④) and then remove the front a. ④ のネジ 6 本を外し、フロントパネルユニットを前方
panel unit forward. (Fig. 1) に外します。（Fig. 1）
b. Remove 4 push rivets and then remove the side plate b. プッシュリベット 4 個を外し、サイドプレート（L）、
(L) and the side plate (R). (Fig. 1) サイドプレート（R）を外します。（Fig. 1）
c. Remove 2 screws (⑤), 2 screw (⑥), 3 screws (⑦) and c. ⑤ のネジ 2 本、⑥ のネジ 2 本、⑦ のネジ 3 本、⑧ の
screw (⑧). (Fig. 1) ネジ 1 本を外します。（Fig. 1）
d. Remove CB9, CB77, CB361, CB362, CB454, CB856, d. C B 9 、 C B 7 7 、 C B 3 6 1 、 C B 3 6 2 、 C B 4 5 4 、 C B 8 5 6 、
CB931 and CB952. (Fig. 1) CB931、CB952 を外します。（Fig. 1）
e. Release 2 hooks and then remove the sub-chassis e. フック 2 箇所を外し、サブシャーシユニットを外しま
unit. (Fig. 1) す。（Fig. 1）
RX-A3020/RX-V3073

DIGITAL (1) P.C.B. Top cover

トップカバー
CB952 ③
DAC P.C.B.
CB9 ①
CB931 CB77

CB856

Push rivet
プッシュリベット

CB454 ⑥ ①
CB361 VIDEO (3) P.C.B.
CB362
OPERATION (2) P.C.B. Push rivet
プッシュリベット
Side plate (L)
サイドプレート （L）

④ ⑧
Hook
フック
⑦

Push rivet
Hook ⑥ プッシュリベット
フック

Sub-chassis unit
サブシャーシユニット
④ ⑤ Side plate (R) Push rivet
サイドプレート （R） プッシュリベット
Front panel unit
フロントパネルユニット

18 Fig. 1
 RX-A3020/RX-V3073

3. Removal of DIGITAL (1) P.C.B. 3. DIGITAL（1）P.C.B. の外し方

a. Remove 3 screws (⑨). (Fig. 2) a. ⑨ のネジ 3 本を外します。（Fig. 2）
b. Remove 10 screws (⑩) and 3 screws (⑪). (Fig. 3) b. ⑩ ネジ 10 本、⑪ のネジ 3 本を外します。（Fig. 3）
c. Remove CB21, CB22, CB70, CB71, CB73 – CB76, c. CB21、CB22、CB70、CB71、CB73 ∼ CB76、CB923、
CB923, CB930 and CB942. (Fig. 2) CB930、CB942 を外します。（Fig. 2）
d. Remove CB943, CB944 and CB945 and then remove d. CB943、CB944、CB945 を外し、DIGITAL（1）P.C.B. を
the DIGITAL (1) P.C.B. which is connected directly to 外します。
the DAC P.C.B. with board-to-board connectors. (Fig. 2) ただし、DIGITAL（1）P.C.B. は DAC P.C.B. に基板対基
板コネクターで直接接続されています。
（Fig. 2）

CB22 CB21 ⑨
CB71
CB930
CB943
CB70 CB944 DIGITAL (1) P.C.B.
CB942

CB945
CB75

RX-A3020/RX-V3073
CB73
Board-to-board connectors
CB74 基板対基板コネクター
CB923
CB76 Board-to-board connectors
基板対基板コネクター

CB851
CB852

CB854
DAC P.C.B.

Fig. 2

⑩ ⑪ ⑩
Rear view

Fig. 3

19
 RX-A3020/RX-V3073

4. Removal of VIDEO (1) P.C.B. 4. VIDEO（1）P.C.B. の外し方

a. Remove 11 screws (⑫). (Fig. 4) a. ⑫ のネジ 12 本を外します。（Fig. 4）
b. Remove CB304, CB331, CB332 (C, R, T, K, A, B, G, F, b. CB304、CB331 ∼ 333、CB332 を外します。（Fig. 5）
L models), CB333 and CB334 (U model). (Fig. 5) c. フック 2 ヶ所を外し、VIDEO（1）P.C.B. を外します。
c. Release 2 hooks and then remove the VIDEO (1) P.C.B. （Fig. 5）
(Fig. 5)

5. Removal of FUNCTION (1), (2) and DAC P.C.B.s 5. FUNCTION（1）、（2）、DAC P.C.B. の外し方
a. Remove screw (⑬). (Fig. 5) a. ⑬ のネジ 1 本を外します。（Fig. 5）
b. Remove 18 screws (⑭). (Fig. 4) b. ⑭ のネジ 18 本を外します。（Fig. 4）
c. Remove CB112, CB113 and CB855. (Fig. 5) c. CB112、CB113、CB855 を外します。（Fig. 5）
d. Release hook and then remove the FUNCTION (1) P.C.B. d. フック 1 ヶ所を外し、FUNCTION（1）P.C.B. を
together with the FUNCTION (2) and DAC P.C.B.s. FUNCTION（2）、DAC P.C.B. と一緒に外します。（Fig. 5）
(Fig. 5)

⑭ ⑫ J model ⑫ Rear view

Hook
RX-A3020/RX-V3073

フック

Fig. 4

CB331
CB334 VIDEO (1) P.C.B.
(U model) CB333 CB304
CB332
(C, R, T, K, A, B, G, F, L, S, J models)

DAC P.C.B.
FUNCTION (1) P.C.B.

CB113 Hook
フック
AMP (1) P.C.B.

CB855

AMP (2) P.C.B.

CB112 FUNCTION (2) P.C.B.

Fig. 5

20
 RX-A3020/RX-V3073

When checking the P.C.B.: P.C.B. をチェックする場合には：

• Put the rubber sheet and the cloth over this unit, and ・ 本機の上にゴムシートと布を敷き、その上にサブ
place the sub-chassis unit on them as shown below. シャーシユニットを置きます。（Fig. 6）
(Fig. 6) ・ アンプユニット（L）とアンプユニット（R）のヒー
• Connect the heatsink of the AMP unit (L) and the トシンクをリード線でシャーシに接続してください。
AMP unit (R) to the chassis with a ground lead. (Fig. 6) （Fig. 6）
• Reconnect all cables (connectors) that have been ・ 外したケーブル（コネクター）をすべて接続します。
disconnected. ・ フラットケーブルを接続する際、極性に注意してく
• When connecting the flexible flat cable, be careful ださい。
with polarity.

RX-A3020/RX-V3073
Sub-chassis unit AMP unit (R)
サブシャーシユニット アンプユニット （R）

Heatsink
Rubber sheet and cloth ヒートシンク
ゴムシートと布

AMP unit (L)

アンプユニット （L）
Ground lead
Chassis アース線
Ground lead シャーシ
Heatsink
アース線 ヒートシンク

Fig. 6

21
 RX-A3020/RX-V3073

■ UPDATING FIRMWARE / ファームウェアのアップデート

When the following parts are replaced, the firmware must 下記の部品を交換した場合、ファームウェアを最新バー
be updated to the latest version. ジョンにアップデートする必要があります。
DIGITAL P.C.B. DIGITAL P.C.B.
GUI Flash ROM: IC75 on DIGITAL (1) P.C.B. GUI フラッシュ ROM： DIGITAL（1）P.C.B. の IC75
DSP1(TI) Flash ROM: IC910 on DIGITAL (1) P.C.B. DSP1（TI）フラッシュ ROM：DIGITAL（1）P.C.B. の IC910
DSP2(TI) Flash ROM: IC921 on DIGITAL (1) P.C.B. DSP2（TI）フラッシュ ROM：DIGITAL（1）P.C.B. の IC921
NETWORK Flash ROM: IC953 on DIGITAL (1) P.C.B. NETWORK フラッシュ ROM：DIGITAL（1）P.C.B. の IC953

● Confirmation of firmware version and checksum ● ファームウェアのバージョンとチェックサムの確認

Before and after updating the firmware, check the ファームウェアのアップデートの前後に、ファーム
firmware version and checksum by using the self- ウェアのバージョンとチェックサムをダイアグで確
diagnostic function menu. 認します。
Start up the self-diagnostic function and select “S4. ダイアグを起動し、 S4. ROM VERSION/CHECKSUM
ROM VERSION/CHECKSUM” menu. メニューを選択します。
Using the sub-menu, have the firmware version and サブメニューでファームウェアのバージョンと
checksum displayed, and note them down. チェックサムを表示し、それらを書きとめます。
(See “SELF-DIAGNOSTIC FUNCTION”) （「ダイアグ」参照）
* When the firmware version and checksum are ※ アップデート後、ファームウェアのバージョンと
RX-A3020/RX-V3073

different from written ones after updating, perform チェックサムが書き込まれたものと異なる場合、

アッ
the updating procedure again from the beginning. プデートの操作を最初からやり直してください。

● Initializing the back-up IC ● バックアップ IC の初期化

(EEPROM: IC78 on DIGITAL (1) P.C.B.) （EEPROM：DIGITAL（1）P.C.B. の IC78）
After updating the firmware, the back-up IC MUST ファームウェアのアップデート後、設定情報（音
be initialized by the following procedure to store the 場プログラムのパラメーターやシステムメモリー、
setting information (soundfield parameters, system チューナープリセット等）を正常に保存するために、
memory and tuner presetting, etc.) properly. 下記の方法でバックアップ IC を初期化する必要が
あります。

Start up the self-diagnostic function and select “S3. 本機のダイアグを起動し、 S3. FACTORY PRESET メ
FACTORY PRESET” menu. (See “SELF-DIAGNOSTIC ニューを選択します。
FUNCTION”) （「ダイアグ」参照）
Select “PRESET RSRV”, press the “MAIN ZONE ” PRESET RSRV を選択し、 MAIN ZONE キーを押
key to turn off the power once and turn on the power して電源を一度きってから、もう一度電源を入れる
again. Then the back-up IC is initialized. とバックアップ IC が初期化されます。

● Required Tools ● 必要なツール

• USB storage device ・ USB フラッシュメモリー
• Firmware ・ ファームウェア
RX-A3020/RX-V3073: R0316-xxxx.bin RX-A3020： R0316-xxxx.bin

● Preparation ● 準備
1. Download the latest firmware from the specified 1. 指定のダウンロード先から、最新のファームウェ
download source to the folder of the PC. アを PC のフォルダへダウンロードしてください。
2. PC から USB フラッシュメモリーのルートフォル
2. Copy the latest firmware from the PC to the root
ダへ最新のファームウェアをコピーします。
folder of the USB storage device.
注意）最新のファームウェアをサブフォルダにコピー
Note) When the latest firmware is copied to a sub-
した場合、書き込みはできません。
folder of the USB storage device, the update
will not proceed.
22
 RX-A3020/RX-V3073

● Operation Procedures ● 操作手順

1. Insert the USB storage device to the USB jack. 1. USB 端子に USB フラッシュメモリーを差し込みま
(Fig. 1) す。（Fig. 1）
2. While pressing the “PURE DIRECT” key, connect 2. PURE DIRECT キーを押しながら、電源コードを
the power cable to the AC outlet. (Fig. 1) AC コンセントに接続します。（Fig. 1）

"MAIN ZONE " key "PURE DIRECT" key

"MAIN ZONE " キー "PURE DIRECT" キー

USB jack
USB 端子

USB storage device

USB フラッシュメモリー

RX-A3020/RX-V3073
Fig. 1

3. The USB UPDATE mode is activated and “USB 3. USB UPDATE モードが起動し、 USB UPDATE が
UPDATE” is displayed. Writing of the firmware 表示されて、ファームウェアの書き込みが自動的
starts automatically. (Fig. 2) に開始されます。（Fig. 2）

Writing is started. / 書き込み開始 Writing being executed. / 書き込み中

USB UPDATE VERIFYING... Sx-x:xx%

Fig. 2

* If “ERROR! xxxx” is displayed during writing of ※ ファームウェアの書き込みの途中で ERROR!

the firmware, refer to “List of Error Messages” xxxx が表示された場合、 エラーメッセージ
to determine the cause and perform the 一覧 で原因を参照し、アップデートの操作
updating procedure again from the beginning. を最初からやり直してください。

4. When writing of the firmware is completed, 4. フ ァ ー ム ウ ェ ア の 書 き 込 み 完 了 後、 UPDATE

“UPDATE SUCCESS”, “PLEASE...” and “POWER SUCCESS 、 PLEASE... 、 POWER OFF! が繰り返
OFF!” are displayed repeatedly. (Fig. 3) し表示されます。（Fig. 3）

Writing is completed. / 書き込み完了

UPDATE SUCCESS PLEASE... POWER OFF!

Fig. 3

5. Press the “MAIN ZONE ” key to turn off the 5. MAIN ZONE （電源）キーを押して電源を切り
power. (Fig. 1) ます。（Fig. 1）
6. Remove the USB storage device from the USB 6. USB 端子から USB フラッシュメモリーを抜きま
jack. (Fig. 1) す。（Fig. 1）
7. Start up the self-diagnostic function and check 7. ダイアグを起動し、ファームウェアのバージョン
that the firmware version and checksum are とチェックサムが、書き込まれたものと同じであ
the same as written ones. (See “Confirmation of ることを確認します。
（ ファームウェアのバージョ
firmware version and checksum”) ンとチェックサムの確認 参照）
23
 RX-A3020/RX-V3073

List of Error Messages / エラーメッセージ一覧

Display / 表示

ERROR! xxxx
Error number / エラー番号

Error Number Error Message Cause

エラー番号 エラーメッセージ 原因
0001 Microprocessor clearing error / マイコン消去エラー Microprocessor failure
0002 Microprocessor writing error / マイコン書き込みエラー マイコン不良
0004 Microprocessor checksum error Microprocessor failure / Mismatch of checksum
マイコンチェックサムエラー マイコン不良／チェックサムの不一致
0008 DSP1 status port error / DSP1 ステータスポートエラー
0010 DSP1 checksum error / DSP1 チェックサムエラー DSP1 failure /
0020 DSP1 data reception time out Malfunction of communication with microprocessor
DSP1 データ受信タイムアウト
0040 DSP1 checksum calculation time out DSP1 不良／マイコンとの通信異常
DSP1 チェックサム計算タイムアウト
RX-A3020/RX-V3073

0080 DSP2 status port error / DSP2 ステータスポートエラー

0100 DSP2 checksum error / DSP2 チェックサムエラー DSP2 failure /
0200 DSP2 date reception time out Malfunction of communication with microprocessor
DSP2 データ受信タイムアウト
0400 DSP2 checksum calculation time out DSP2 不良／マイコンとの通信異常
DSP2 チェックサム計算タイムアウト
0800 GUI Flash ROM clearing error
GUI Flash ROM 消去エラー GUI Flash ROM failure /
1000 GUI Flash ROM writing error Malfunction of communication with microprocessor
GUI Flash ROM 書き込みエラー
2000 GUI Flash ROM checksum error GUI Flash ROM 不良／マイコンとの通信異常
GUI Flash ROM チェックサムエラー
4000 Destination judging error No destination is written on EEPROM.
仕向け先判定エラー EEPROM に仕向け先が書かれていない

* The error number is displayed in the 4-digit hexadecimal notation.

エラー番号は 4 桁の 16 進数で表示されます。

* The error numbers are added when a multiple number of errors occur at the same time.
エラー番号は同時に複数のエラーが発生すると、加算されます。

Example / 例 If errors by the error number “0002” and “0008” occur at the same time, the error number will be displayed as “000A”.
エラー番号の“0002”と“0008”のエラーが同時に発生すると、エラー番号は“000A”と表示されます。

24
 RX-A3020/RX-V3073

■ SELF-DIAGNOSTIC FUNCTION / ダイアグ（自己診断機能）

This unit has self-diagnostic functions that are intended 本機には、検査、測定、不良個所の発見を目的にしたダ
for inspection, measurement and location of faulty point. イアグ（自己診断機能）があります。
There are 26 main menu items, each of which has sub- ダイアグには 26 個のメインメニューがあり、そのそれぞ
menu items. れにサブメニューがあります。
Listed in the table below are main menu items and sub- 下表はダイアグメニュー一覧です。
menu items.
注意： 以下のメニュー項目の一部は、このサービスマニュ
Note: Some of the menu items listed below may not apply アルに記載されているモデルに適用されない場合
to the models covered in this service manual. があります。

No. Main menu No. Sub-menu

A: Audio system
A1 DSP AUDIO 1 DSP MARGIN
2 DSP NON MARGIN
3 PLL OFF
4 INVALID ITEM (Not for service / サービスでは使用しません )
5 INVALID ITEM (Not for service / サービスでは使用しません )
6 INVALID ITEM (Not for service / サービスでは使用しません )
7 INVALID ITEM (Not for service / サービスでは使用しません )
A2 DIRECT AUDIO 1 ANALOG DIRECT VH
2 ANALOG DIRECT VL
A3 HDMI AUDIO 1 HDMI AUTO

RX-A3020/RX-V3073
2 DSD DIRECT
3 ARC1
4 HDMI ZONE
5 HDMI THROUGH (Not for service / サービスでは使用しません )
A4 SPEAKERS SET 1 BI-AMP
2 ZONE/TONE MAX
3 ZONE/TONE MIN
4 ZONE MONO ON
5 ZONE MONO OFF
6 D-PARTY MODE
7 FULL MUTE
8 EXTERNAL FRONT/INTERNAL REAR PRESENCE
9 EXTERNAL FRONT/INTERNAL ZONE 2
10 EXTERNAL FRONT/INTERNAL ZONE 3
A5 MULTI CHANNEL INPUT 1 MULTI CHANNEL INPUT 8 ohms
2 MULTI CHANNEL INPUT 6 ohms
A6 MIC CHECK 1 MIC ROUTE CHECK
A7 MANUAL TEST 1 TEST ALL
2 TEST FRONT L
3 TEST CENTER
4 TEST FRONT R
5 TEST SURROUND R
6 TEST SURROUND BACK R
7 TEST SURROUND BACK L
8 TEST SURROUND L
9 TEST FRONT PRESENCE L
10 TEST FRONT PRESENCE R
11 TEST REAR PRESENCE L
12 TEST REAR PRESENCE R
13 TEST LFE 1
14 TEST LFE 2
D: Display system
D1 FL CHECK 1 FL CHECK
2 ALL SEGMENT OFF
3 ALL SEGMENT ON
4 CHECK PATTERN 1
5 CHECK PATTERN 2
25
 RX-A3020/RX-V3073

No. Main menu No. Sub-menu

Z: Zone system
Z1 ZONE TEST 1 AV 1
2 AV 2
3 AV 3
4 AV 4
5 AUDIO 1
6 AUDIO 2
7 AUDIO 3
8 AUDIO 4
9 V-AUX
10 PHONO
U: Universal system
U1 USB 1 USB FRONT 1 TRACK
2 USB FRONT 2 TRACK
3 USB_VBUS HIGH POWER
N: Network system
N1 NETWORK 1 IP ADDRESS CHECK
2 MAC ADDRESS CHECK
3 LINE NOISE 100 MDI (Not for service / サービスでは使用しません )
4 LINE NOISE 100 MDIX (Not for service / サービスでは使用しません )
RX-A3020/RX-V3073

5 LINE NOISE 10 MDI (Not for service / サービスでは使用しません )

6 LINE NOISE 10 MDIX (Not for service / サービスでは使用しません )
7 EXT TEST
8 MAC ADDRESS
C: Communication system
C1 DIGITAL PCB CHECK 1 ALL (Not for service / サービスでは使用しません )
2 BUS FLASH ROM
3 BUS FPGA
4 I2C
5 FPGA RAM
6 BUS DIR1
7 BUS DSP1
8 EEPROM
9 RS-232C DATA CHECK (Not for service / サービスでは使用しません )
10 BUS DIR2
11 BUS DSP2
C2 NETWORK IC CHECK 1 ALL
2 LINK CHECK
3 PHY TEST
4 BUS RAM
5 APL ID CHECK
V: Video system
V1 ANALOG VIDEO CHECK 1 ANALOG BYPASS
2 DIGITAL BYPASS
3 ZONE BYPASS
4 MUTE CHECK
5 TEST PATTERN (Not for service / サービスでは使用しません )
6 VIDEO IN
V2 DIGITAL VIDEO CHECK 1 LOOPBACK TEST 1
2 LOOPBACK TEST 2
3 LOOPBACK TEST 3
4 LOOPBACK TEST 4
5 LOOPBACK TEST 5
6 LOOPBACK TEST 6
7 HDMI REPEAT

26
 RX-A3020/RX-V3073

No. Main menu No. Sub-menu

V2 DIGITAL VIDEO CHECK 8 DIGITAL CVBS
9 DIGITAL Y/C
10 DIGITAL COMPONENT
11 DIGITAL COMPONENT SC
12 GUI-VIDEO OUT
V3 TEST PATTERN 1 480i
2 480p
3 720p 60Hz
4 1080i 60Hz
5 1080p 60Hz
6 576i
7 576p
8 720p 50Hz
9 1080i 50Hz
10 1080p 50Hz
11 1080p 24Hz
12 1080p 24Hz 3D/FP
13 720p 60Hz 3D/FP
14 720p 50Hz 3D/FP
15 1080i 60Hz 3D/FP

RX-A3020/RX-V3073
16 1080i 60Hz 3D/SS
17 1080i 50Hz 3D/SS
18 720p 60Hz 3D/TB
19 720p 50Hz 3D/TB
20 1080p 24Hz 3D/TB
21 4k 24Hz
T: Troubleshooting Information
T1 POWER 1 OPERATING TIME
2 POWER-RELAY ON
3 POWER AMP B
4 OUTPUT LEVEL
5 POWER OFF TIME-OUT
T2 USAGE ENVIRONMENT 1 MAIN ZONE HIGHEST VOLUME
2 ZONE 2 HIGHEST VOLUME
3 ZONE 3 HIGHEST VOLUME
4 THM1/THM2 HIGHEST TEMPERATURE
5 THM3/THM4 HIGHEST TEMPERATURE
(Not for service / サービスでは使用しません )
T3 EXTERNAL EVENT 1 HISTORY 1
2 HISTORY 2
3 HISTORY 3
4 HISTORY 4
5 HISTORY 5
6 HISTORY 6
7 HISTORY 7
8 HISTORY 8
T4 INTERNAL INFOMATION 1 DSP INFORMATION
P: Power and protection system
P1 SYSTEM MONITOR 1 DC
2 PS1/PS2/PS3
3 THM1/THM2
4 THM3/THM4 (Not for service / サービスでは使用しません )
5 OUTPUT LEVEL
6 LIMITER CONTROL
7 L3 (J model)
8 KEY1/KEY2/KEY3
9 USB-VBUS (Not for service / サービスでは使用しません )
27
 RX-A3020/RX-V3073

No. Main menu No. Sub-menu

P2 PROTECTION HISTORY 1 HISTORY 1
1-1 POWER PORT
1-2 POWER ON TIME
1-3 LAST INPUT
1-4 LAST VOLUME
2 HISTORY 2
2-1 POWER PORT
2-2 POWER ON TIME
2-3 LAST INPUT
2-4 LAST VOLUME
3 HISTORY 3
3-1 POWER PORT
3-2 POWER ON TIME
3-3 LAST INPUT
3-4 LAST VOLUME
4 HISTORY 4
4-1 POWER PORT
4-2 POWER ON TIME
4-3 LAST INPUT
4-4 LAST VOLUME
RX-A3020/RX-V3073

S: System and version system

S1 FIRMWARE UPDATE 1 F/W UPDATE (Not for service / サービスでは使用しません )
S2 SET INFORMATION 1 MODEL
2 DESTINATION
3 DBG (Not for service / サービスでは使用しません )
4 NET RESTART COUNTER (Not for service / サービスでは使用しません )
S3 FACTORY PRESET 1 PRESET INHIBIT/RESERVE
S4 ROM VERSION/CHECKSUM 1 SYSTEM VERSION
2 MICROPROCESSOR VERSION
3 MICROPROCESSOR CHECKSUM
4 FLASH ROM VERSION
5 FLASH ROM CHECKSUM
6 NETWORK MICROPROCESSOR VERSION
7 NETWORK MICROPROCESSOR CHECKSUM
8 DSP1 VERSION
9 DSP1 CHECKSUM
10 DSP2 VERSION
11 DSP2 CHECKSUM
12 GUI VERSION
13 FPGA GUI VERSION
14 FPGA SD VERSION
15 FPGA HD VERSION
16 HQV VERSION
17 HD RADIO VERSION (U model)

28
 RX-A3020/RX-V3073

● Starting Self-Diagnostic Function ● ダイアグの起動

While pressing the “TONE/BALANCE” and “INFO” keys, TONE/BALANCE と INFO キーを押しながら MAIN
press the “MAIN ZONE ” key to turn on the power, and ZONE キーを押して電源を入れた後、2 つのキーを放
release those 2 keys. します。
The self-diagnostic function mode is activated. ダイアグが起動します。

Keys of this unit / 本機キー

While pressing these keys, turn on the power.

これらのキーを押しながら、電源を入れます。

RX-A3020/RX-V3073
● Starting Self-Diagnostic Function in ● プロテクション解除モードでの起動
the protection cancel mode
If the protection function works and causes hindrance プロテクションが動作することにより、故障箇所の診断
to troubleshooting, cancel the protection function by the に支障をきたすような場合は、次の方法によりプロテク
procedure below, and it will be possible to enter the self- ションを解除した状態でダイアグモードに入ることがで
diagnostic function mode. (The protection functions other きます。（過電流検出と PS3 プロテクション以外のプロテ
than the excess current detect function and PS3 protection クション動作を解除する）
function will be disabled.) TONE/BALANCE と INFO キーを押しながら MAIN
While pressing the “TONE/BALANCE” and “INFO” keys, ZOE キーを押して電源を入れ、２つのキーと MAIN
press the “MAIN ZONE ” key to turn on the power and ZOE キーを 3 秒以上押し続けます。
keep pressing those 2 keys and “MAIN ZONE ” key for 3 プロテクション解除モードでダイアグが起動します。
seconds or longer.
このモードでは FL の SLEEP セグメントが点滅し、プロ
The self-diagnostic function mode is activated with the テクションを解除した状態でのダイアグモードであるこ
protection functions disabled. とを知らせます。
In this mode, the “SLEEP” segment of the FL display flashes
to indicate that the mode is self-diagnostic function mode
with the protection functions disabled.

CAUTION! 注意！
Using this unit with the protection function disabled may プロテクションを解除した状態でのダイアグモードは、
cause further damage to this unit. Use special care for 危険な状態でもプロテクションが作動しないため、動作
this point when using this mode. させると、本機を破壊することがあります。このモード
を使用する場合は十分注意してください。

29
 RX-A3020/RX-V3073

● Canceling Self-Diagnostic Function ● ダイアグの解除

1. Before canceling self-diagnostic function, execute 1. ダイアグを解除する前に、 S3. FACTORY PRESET メ
setting for “S3. FACTORY PRESET” menu. (Memory ニュー（メモリーの初期化禁止／またはメモリーの
initialization inhibited or Memory initialized). 初期化）の設定をします。
* In order to keep the user memory preserved, be ※ ユ ー ザ ー メ モ リ ー を 保 持 し た い 場 合 は、 必 ず
sure to select PRESET INHIBIT (Memory initialization PRESET INHIBIT（メモリー初期化禁止）を選択し
inhibited). てください。
2. Press the “MAIN ZONE ” key to turn off the power. 2. MAIN ZONE キーを押して電源を切ります。

● Display provided when Self-Diagnostic ● ダイアグ起動時の表示

Function started
The display is as described below depending on the 本機の電源が切れたときの状況により、下記のように表
situation when the power to this unit is turned off. 示されます。

1. When the power is turned off by usual operation: 1. 通常の操作で電源を切った場合：

RX-A3020/RX-V3073

“NO PROTECT” is displayed. Then “A1-1. DSP NO PROTECT が表示されます。数秒後、 A1-1. DSP
MARGIN” is displayed in a few seconds. MARGIN が表示されます。

Opening message / オープニング表示 Main menu display / メインメニュー表示

After a few seconds / 数秒後

A1-1
NO PROTECT DSP MARGIN

30
 RX-A3020/RX-V3073

2. When the protection function worked to turn 2. プロテクションが働いて電源が切れた場合：

off the power:
The information of protection function which worked at そのときに働いたプロテクションの情報が表示され
that time is displayed. Then “A1-1. DSP MARGIN” is ます。数秒後、 A1-1. DSP MARGIN が表示されます。
displayed in a few seconds. 注） このとき、一旦電源を切った後にダイアグを再
Note: At that time if you restart the self-diagnostic 起動すると、 NO PROTECT が表示されます。
function after turning off the power once, “NO それは、その状況が「1. 通常の操作で電源を切っ
PROTECT” will be displayed. That is because た場合：」と同じだからです。
that situation is equal to “1. When the power is ただし、プロテクションの履歴はバックアップ
turned off by usual operation:”. データとしてメモリーに保存されます。詳細は、
However history of the protection function is P2. PROTECTION HISTORY メニューを参照し
stored in memory as backup data. For details, てください。
refer to “P2. PROTECTION HISTORY” menu.

2-1. When there is a history of protection function 2-1. 過電流によるプロテクション履歴がある場合

due to excess current.

I PROTECT

RX-A3020/RX-V3073
Cause: An excessive current flowed through the power 原因： パワーアンプに過電流が流れた。
amplifier. 補足： パワーアンプの電流を検出していますので、電流
Supplementary information: As over current of the 検出トランジスタをチェックすれば異常チャンネ
power amplifier is detected, check condition of each ルが特定できます。
power transistor.
異常状態のまま電源を入れると、瞬時にプロテクション
Turning on the power without correcting the abnormality
が働き、すぐに電源が切れます。
will cause the protection function to work immediately and
the power supply will instantly be shut off.

Notes: 注意：
• Applying the power to this unit without correcting ・ 異常状態のまま本機の電源を入れると、危険な状態
the abnormality can be dangerous and cause になり、さらに回路が損傷を受ける原因になります。
additional circuit damage. To avoid this, if “I それを避けるために、 「I PROTECT」が１回働いた場
PROTECT” protection function works 1 time, 合、それ以降 MAIN ZONE キーを押しても電源
the power will not turn on even when the “MAIN が入らなくなります。再度電源を入れる場合、ダイ
ZONE ” key is pressed. In order to turn on the アグを起動してください。
power again, start up the self-diagnostic function. ・ 本機の電源をいれる前に、各パワーアンプの出力ト
• The output transistors in each amplifier channel ランジスタに損傷がないかチェックしてください。
should be checked for damage before applying ・ パワーアンプの電流は、各チャンネルのエミッター
power to this unit. の抵抗器間 DC 電圧を測定することによりモニター
• Amplifier current should be monitored by してください。
measuring DC voltage across the emitter resistors
for each channel.

31
 RX-A3020/RX-V3073

2-2. When the protection function worked due to 2-2. DC 出力異常によりプロテクションが働いた場合

abnormal DC output.

DC PRT:xxxH H: Displayed when the voltage is HIGHER than upper limit

電圧が上限値より高い場合に表示されます
L: Displayed when the voltage is LOWER than lower limit
電圧が下限値より低い場合に表示されます
xxx: A/D conversion value of voltage at the moment when the protection function worked
(Reference voltage: 3.3 V=255)
プロテクションが働いた瞬間の電圧の A/D 変換値
（基準電圧：3.3 V=255）

Cause: DC output of the power amplifier is abnormal. 原因： パワーアンプの DC 出力が異常。

Supplementary information: The protection function 補足： アンプの故障でスピーカー端子に直流電圧が掛か
worked due to a DC voltage appearing at the speaker るなどが原因で、プロテクションが働いたことを
terminal. A cause could be a defect in the amplifier. 示します。
Turning on the power without correcting the abnormality
異常状態のまま電源を入れると、5 秒後にプロテクション
will cause the protection function to work in 5 seconds
が働き、電源が切れます。
and the power supply will be shut off.
RX-A3020/RX-V3073

2-3. When the protection function worked due to 2-3. 電源部の電圧異常によりプロテクションが働い

abnormal voltage in the power supply section. た場合

PSxPRT:xxxL H: Displayed when the voltage is HIGHER than upper limit

電圧が上限値より高い場合に表示されます
L: Displayed when the voltage is LOWER than lower limit
電圧が下限値より低い場合に表示されます
xxx: A/D conversion value of voltage at the moment when the protection function worked
(Reference voltage: 3.3 V=255)
プロテクションが働いた瞬間の電圧の A/D 変換値
（基準電圧：3.3 V=255）
PS1/PS2/PS3

Cause: The voltage in the power supply section is 原因： 電源部の電圧が異常。

abnormal. 補足： 電源電圧による原因で、プロテクションが働いた
Supplementary information: The protection function ことを示します。
worked due to a defect or overload in the power supply.
異常状態のまま電源を入れると、1 秒後にプロテクション
Turning on the power without correcting the abnormality
が働き、電源が切れます。
will cause the protection function to work in 1 seconds
and the power supply will be shut off.

Notes: 注意：
• Applying the power to this unit without correcting ・ 異常状態のまま本機の電源を入れると、危険な状態
the abnormality can be dangerous and cause になり、さらに回路が損傷を受ける原因になりま
additional circuit damage. To avoid this, if “PS” す。それを避けるために、 「DC」、
「PS」プロテクショ
and “DC” protection function works 3 times ンが連続して 3 回目働いた場合、それ以降 MAIN
consecutively, the power will not turn on even ZONE キーを押しても電源が入らなくなります。
when the “MAIN ZONE ” key is pressed. In order 再度電源を入れる場合、ダイアグを起動してくださ
to turn on the power again, start up the self- い。
diagnostic function. ・ 本機の電源をいれる前に、各パワーアンプの出力ト
• The output transistors in each amplifier channel ランジスタに損傷がないかチェックしてください。
should be checked for damage before applying ・ パワーアンプの電流は、各チャンネルのエミッター
power to this unit. の抵抗器間 DC 電圧を測定することによりモニター
• Amplifier current should be monitored by してください。
measuring DC voltage across the emitter resistors
for each channel.
32
 RX-A3020/RX-V3073

2-4. When the protection function worked due to 2-4. ヒートシンクの異常温度によりプロテクション

excessive heatsink temperature. が働いた場合

TMPxPRT:xxxL H: Displayed when the voltage is HIGHER than upper limit

電圧が上限値より高い場合に表示されます
L: Displayed when the voltage is LOWER than lower limit
電圧が下限値より低い場合に表示されます
xxx: A/D conversion value of voltage at the moment when the protection function worked
(Reference voltage: 3.3 V=255)
プロテクションが働いた瞬間の電圧の A/D 変換値
（基準電圧：3.3 V=255）
TMP1/TMP2/TMP3

Cause: The temperature of the heatsink is excessive. 原因： ヒートシンクの温度が異常。

Supplementary information: The protection function 補足： 温度制限を越えた原因で、プロテクションが働い
worked due to the temperature limit being exceeded. たことを示します。
Causes could be poor ventilation or a defect related to
the thermal sensor. 異常状態のまま電源を入れると、1 秒後にプロテクション
が働き、電源が切れます。
Turning on the power without correcting the abnormality
will cause the protection function to work in 1 seconds

RX-A3020/RX-V3073
and the power supply will be shut off.

● History of protection function ● プロテクションの履歴

When the protection function has worked, its history プロテクションが働いた場合、その履歴はバックアッ
is stored in memory as backup data. プデータとしてメモリーに保存されます。
Even if no abnormality is noted while servicing the 修理のときに異常が認められなくても、バックアッ
unit, an abnormality which has occurred previously プデータが残っていれば、お客様のところで起きた
can be defined as long as the backup data has been 異常を区別できます。
stored. 詳細は、 P2. PROTECTION HISTORY メニューを参照
For details, refer to “P2. PROTECTION HISTORY” してください。
menu.

33
 RX-A3020/RX-V3073

● Operation procedure of Main menu ● メインメニューとサブメニューの操作

and Sub-menu
There are 26 main menu items, each of which has sub- ダイアグには 26 個のメインメニューがあり、そのそれぞ
menu items. れにサブメニューがあります。

Main menu selection メインメニューの選択

Select the main menu using “SCENE 2” (forward) and SCENE 2（順送り）、SCENE 1（逆送り）キーで選択します。
“SCENE 1” (reverse) keys.

Sub-menu selection サブメニューの選択

Select the sub-menu using “SCENE 4” (forward) and “SCENE SCENE 4（順送り）、SCENE 3（逆送り）キーで選択します。
3” (reverse) keys.
Keys of this unit / 本機キー

Main menu selection Sub-menu selection

メインメニューの選択 サブメニューの選択
RX-A3020/RX-V3073

Reverse Forward Reverse Forward

逆送り 順送り 逆送り 順送り

● Functions in Self-Diagnostic Function ● ダイアグ中の機能

mode
In addition to the self-diagnostic function menu items, ダイアグメニューの他に、以下の機能が動作します。
functions listed below are available.
・ 電源 オン／オフ
• Power ON/OFF ・ マスターボリューム
• Master volume ・ ミューティング
• Muting ・ インプットセレクト
• Input selection ・ ZONE コントロール
• Zone control ※ チューナー関連、セットメニュー関連は機能しません。
* Functions related to the tuner and the set menu are
not available.

● Initial settings when Self-Diagnostic ● ダイアグ開始時の初期設定

Function started
The following initial settings are used when self-diagnostic ダイアグ開始時に以下のような設定になります。
function is started. ・ マスターボリューム： -20 dB
• Master volume: -20 dB ZONE 2 ボリューム： -3.5 dB
ZONE 2 volume: -3.5 dB ZONE 3 ボリューム： -3.5 dB
ZONE 3 volume: -3.5 dB ・ インプット： HDMI1 ／ ZONE インプット：
• Input: HDMI1 / Zone input: AUDIO 1 AUDIO 1
• Main menu: A1-1. DSP MARGIN ・ メインメニュー： A1-1. DSP MARGIN
• Speaker setting: LARGE, Bass out to SWFR ・ スピーカー設定： LARGE、Bass out to SWFR
(All channels) （すべてのチャンネル）
• HDMI control: Off ・ HDMI コントロール： OFF
• ZONE 2/ZONE 3/ZONE 4: On ・ ZONE 2 ／ ZONE 3 ／ ZONE 4： ON

* When self-diagnostic function is canceled, these ※ ダイアグ解除時にはダイアグ開始前の状態に戻りま

settings are restored to those before starting self- す。

34 diagnostic function.
 RX-A3020/RX-V3073

● Details of Self-Diagnostic Function ● ダイアグメニュー詳細

menu
A1. DSP AUDIO A1. DSP AUDIO
This menu is used to check audio signal route via DSP. DSP を経由する音声信号の経路をチェックします。

A1-1. DSP MARGIN A1-1. DSP MARGIN

The audio signal is output including the head 音声信号が DSP を経由してヘッドマージンを
margin via DSP. 含んで出力されます。
* When input source is stereo, signal is ※ 2ch 信号入力時、以下のように信号が振り
assigned as below. 分けられて出力されます。
Front L: Front L, Center, Surround L, Front L： Front L、Center、Surround L、
Surround Back L Surround Back L
Front R: Front R, Surround R, Surround Front R： Front R、Surround R、Surround
Back R Back R
Front L +10 dB: Subwoofer Front L +10 dB：Subwoofer

A1-1

RX-A3020/RX-V3073
DSP MARGIN

A1-2. DSP NON MARGIN A1-2. DSP NON MARGIN

The SUBWOOFER signal is output including サブウーファーの音声信号が DSP を経由して
the head margin via DSP. ヘッドマージンを含んで出力されます。
The audio signal other than SUBWOOFER is サブウーファー以外の音声信号は DSP を経由
output without including the head margin via してヘッドマージンを含まず出力されます。
DSP.

A1-2
DSP NON MARGIN

A1-3. PLL OFF A1-3. PLL OFF

The audio signal is output with the PLL (Phase 音声信号が DSP を経由して PLL（Phase Lock
Lock Loop, IC914) turned off via DSP. Loop、IC914）をオフにして出力されます。

A1-3
PLL=OFF

A1-4. INVALID ITEM A1-4. INVALID ITEM

Not for service. サービスでは使用しません

A1-4
INVALID ITEM

35
 RX-A3020/RX-V3073

A1-5. INVALID ITEM A1-5. INVALID ITEM

Not for service. サービスでは使用しません

A1-5
INVALID ITEM

A1-6. INVALID ITEM A1-6. INVALID ITEM

Not for service. サービスでは使用しません

A1-6
INVALID ITEM

A1-7. INVALID ITEM A1-7. INVALID ITEM

Not for service. サービスでは使用しません

A1-7
RX-A3020/RX-V3073

INVALID ITEM

A2. DIRECT AUDIO A2. DIRECT AUDIO

This menu is used to check audio signal route of DIRECT モードの音声信号の経路をチェックします。
PURE DIRECT mode.

A2-1. DIRECT VH A2-1. DIRECT VH

The analog input audio signal is output to アナログ入力の音声信号が PURE DIRECT で
FRONT L/R in PURE DIRECT mode. FRONT L/R へ出力されます。
VH: Voltage High, VH：Voltage High、
RY180 on AMPPOWER (1) P.C.B.: Off AMPPOWER（1）P.C.B. の RY180：Off

A2-1
DIRECT :VH

A2-2. DIRECT VL A2-2. DIRECT VL

The analog input audio signal is output to アナログ入力の音声信号が PURE DIRECT で
FRONT L/R in PURE DIRECT mode. FRONT L/R へ出力されます。
VL: Voltage Low, VL：Voltage Low、
RY180 on AMPPOWER (1) P.C.B.: On AMPPOWER（1）P.C.B. の RY180：On

A2-2
DIRECT :VL

36
 RX-A3020/RX-V3073

A3. HDMI AUDIO A3. HDMI AUDIO

This menu is used to check the route of audio signal HDMI IN/OUT 端子へ入力された音声信号の経路を
input to HDMI IN/OUT jack. チェックします。
* Before check using “A3-3. ARC 1” menu, be sure ※ A3-3. ARC メニューでのチェックの前に、あらか
to connect a TV monitor equipped with Audio じめ必ず Audio Return Channel 機能に対応してい
Return Channel function to this unit in advance. るテレビを接続してください。

A3-1 A3-1. HDMI AUTO

HDMI AUTO The audio signal input to selected HDMI IN jack is output.
選択された HDMI IN 端子へ入力された音声信号が出力されます。

A3-2 A3-2. DSD DIRECT

DSD DIRECT DSD (Direct Stream Digital) is output by the direct mode.
DSD（Direct Stream Digital）がダイレクトモードで出力されます。

A3-3 A3-3. ARC1 (Audio Return Channel function)

ARC 1 The audio signal input to HDMI OUT1 jack is output.
HDMI OUT1 端子へ入力された音声信号が出力されます。

RX-A3020/RX-V3073
A3-4 A3-4. HDMI ZONE
HDMI Zone The audio signal input to HDMI OUT2 jack is output.
HDMI OUT2 端子へ入力された音声信号が出力されます。

A3-5 A3-5. HDMI THROUGH

HDMI Through Not for service.
サービスでは使用しません。

37
 RX-A3020/RX-V3073

A4. SPEAKERS SET A4. SPEAKERS SET

This menu is used to check the speaker output. スピーカー出力をチェックします。

A4-1 A4-1. BI-AMP

BI-AMP The FRONT L/R signal is distributed to BI-AMP L/R terminals.
FRONT L/R の音声信号が BI-AMP L/R 端子へ振り分けられて出力されます。

A4-2 A4-2. ZONE/TONE=MAX

ZONE/TONE=MAX The audio signal is output to FRONT L/R, CENTER, SURROUND L/R, ZONE 2 L/R and ZONE 3 L/R
terminals with the tone control “BASS +6 dB”, “TREBLE +6 dB”.
音声信号がトーンコントロール“BASS +6 dB”
、“TREBLE +6 dB”で FRONT L/R、CENTER、
SURROUND L/R 端子へ出力されます。

A4-3 A4-3. ZONE/TONE=MIN

ZONE/TONE=MIN The audio signal is output to FRONT L/R, CENTER, SURROUND L/R, ZONE 2 L/R and ZONE 3 L/R
terminals with the tone control “BASS -6 dB”, “TREBLE -6 dB”.
音声信号がトーンコントロール“BASS -6 dB”、“TREBLE -6 dB”で FRONT L/R、CENTER、
SURROUND L/R、ZONE 2 L/R、ZONE 3 L/R 端子へ出力されます。
RX-A3020/RX-V3073

A4-4 A4-4. ZONE MONO ON

ZONE MONO=On The analog audio signal is output to ZONE 2 L/R and ZONE 3 L/R terminal in monaural.
アナログ音声信号が ZONE 2 L/R、ZONE 3 L/R 端子へモノラルで出力されます。

A4-5 A4-5. ZONE MONO OFF

ZONE MONO=Off The analog audio signal is output to ZONE 2 L/R and ZONE 3 L/R terminals in stereo.
アナログ音声信号が ZONE 2 L/R、ZONE 3 L/R 端子へステレオで出力されます。

A4-6 A4-6. D-PARTY MODE

D-PARTY MODE The FRONT L/R signal is distributed to ZONE 2 L/R and ZONE 3 L/R terminals.
ZONE 2/ZONE 3 volume: -3.5 dB
FRONT L/R の音声信号が ZONE 2 L/R、ZONE 3 L/R 端子へ振り分けられて出力されます。
ZONE 2 ／ ZONE 3 volume：-3.5 dB

A4-7 A4-7. FULL MUTE

FULL MUTE The SPEAKERS output are muted at all channels.
SPEAKERS 出力がすべてのチャンネルでミュートされます。

A4-8. EXTERNAL FRONT/INTERNAL REAR PRESENCE

A4-8
EXT.F+INT.RPR The audio signal is output to CENTER, SURROUND L/R, SURROUND BACK L/R, FRONT PRESENCE L/
R and REAR PRESENCE L/R.
音声信号が CENTER、SURROUND L/R、SURROUND BACK L/R、FRONT PRESENCE L/R and
REAR PRESENCE L/R へ出力されます。

A4-9. EXTERNAL FRONT/INTERNAL ZONE 2

A4-9
EXT.F+INT.Z2 The audio signal is output to CENTER, SURROUND L/R, SURROUND BACK L/R, ZONE 2 L/R (EXTRA
SP1 L/R) and ZONE 2 L/R (EXTRA SP2 L/R).
音声信号が CENTER、SURROUND L/R、SURROUND BACK L/R、ZONE 2 L/R（EXTRA SP1 L/R）、
ZONE 2 L/R（EXTRA SP2 L/R）へ出力されます。

A4-10
A4-10. EXTERNAL FRONT/INTERNAL ZONE 3
EXT.F+INT.Z3 The audio signal is output to CENTER, SURROUND L/R, SURROUND BACK L/R, ZONE 3 L/R (EXTRA
SP1 L/R) and ZONE 3 L/R (EXTRA SP2 L/R) terminals.
音声信号が CENTER、SURROUND L/R、SURROUND BACK L/R、ZONE 3 L/R（EXTRA SP1 L/R）、
ZONE 3 L/R（EXTRA SP2 L/R）端子へ出力されます。

38
 RX-A3020/RX-V3073

A5. MULTI CHANNEL INPUT A5. MULTI CHANNEL INPUT

This menu is used to check the route of audio signal MULTI CHANNEL INPUT に入力されたオーディオ信号
input to MULTI CHANNEL INPUT. の経路をチェックします。

A5-1. 8 CHANNEL INPUT 8 ohms A5-1. 8 CHANNEL INPUT 8 ohms

The audio signal input to MULTI CHANNEL MULTI CHANNEL INPUT に入力された音声信号
INPUT is output with the speaker impedance “8 がスピーカーインピーダンス 8 オーム の設
ohms” setting. 定で出力されます。

A5-1
8ohm MULTI CH

A5-2. 8 CHANNEL INPUT 6 ohms A5-2. 8 CHANNEL INPUT 6 ohms

The audio signal input to MULTI CHANNEL MULTI CHANNEL INPUT に入力された音声信号
INPUT is output with the speaker impedance “6 がスピーカーインピーダンス 6 オーム の設
ohms” setting. 定で出力されます。

RX-A3020/RX-V3073
A5-2
6ohm MULTI CH

A6. MIC CHECK A6. MIC CHECK

A6-1. MIC ROUTE CHECK A6-1. MIC ROUTE CHECK

The audio signal input to the YPAO MIC jack is YPAO マイク端子へ入力された音声信号が A/D
output to FRONT L and FRONT R channels via − D/A 経由で FRONT L、FRONT R チャンネル
A/D-D/A. へ出力されます。

A6-1
MIC ROUTE

39
 RX-A3020/RX-V3073

A7. MANUAL TEST A7. MANUAL TEST

The test noise or test tone generated by built-in noise DSP に内蔵されたノイズジェネレータによって生成
generator in DSP is output to the channels specified されたテストノイズ・テストトーンが、サブメニュー
by the sub-menu. で指定したチャンネルへ出力されます。

Test noise / テストノイズ Test tone / テストトーン

for SUBWOOFER 30 Hz to 80 Hz 50 Hz
SUBWOOFER 用 pink noise / ピンクノイズ sine wave / 正弦波
for other than SUBWOOFER 500 Hz to 2 kHz 1 kHz
SUBWOOFER 以外 pink noise / ピンクノイズ sine wave / 正弦波

A7-1 A7-1. TEST ALL

TEST ALL The test noise is output to FRONT L/R, CENTER, SURROUND L/R, SURROUND BACK L/R,
FRONT PRESENCE L/R and LFE 1/2 (SUBWOOFER 1/2) channels.
テストノイズが FRONT L/R、CENTER、SURROUND L/R、SURROUND BACK L/R、
FRONT PRESENCE L/R、LFE 1/2（SUBWOOFER 1/2）チャンネルへ出力されます。

A7-2 A7-2. TEST FRONT L

TEST FRNT L The test tone is output to FRONT L channel.
RX-A3020/RX-V3073

テストトーンが FRONT L チャンネルへ出力されます。

A7-3 A7-3. TEST CENTER

TEST CENTER The test tone is output to CENTER channel.
テストトーンが CENTER チャンネルへ出力されます。

A7-4 A7-4. TEST FRONT R

TEST FRNT R The test tone is output to FRONT R channel.
テストトーンが FRONT R チャンネルへ出力されます。

A7-5 A7-5. TEST SURROUND R

TEST SURR R The test tone is output to SURROUND R channel.
テストトーンが SURROUND R チャンネルへ出力されます。

A7-6 A7-6. TEST SURROUND BACK R

TEST SB R The test tone is output to SURROUND BACK R channel.
テストトーンが SURROUND BACK R チャンネルへ出力されます。

A7-7 A7-7. TEST SURROUND BACK L

TEST SB L The test tone is output to SURROUND BACK L channel.
テストトーンが SURROUND BACK L チャンネルへ出力されます。

A7-8 A7-8. TEST SURROUND L

TEST SURR L The test tone is output to SURROUND L channel.
テストトーンが SURROUND L チャンネルへ出力されます。

A7-9 A7-9. TEST FRONT PRESENCE L

TEST FP L The test tone is output to FRONT PRESENCE L channel.
テストトーンが FRONT PRESENCE L チャンネルへ出力されます。

40
 RX-A3020/RX-V3073

A7-10 A7-10. TEST FRONT PRESENCE R

TEST FP R The test tone is output to FRONT PRESENCE R channel.
テストトーンが FRONT PRESENCE R チャンネルへ出力されます。

A7-11 A7-11. TEST REAR PRESENCE L

TEST RP L The test tone is output to REAR PRESENCE L channel.
テストトーンが REAR PRESENCE L チャンネルへ出力されます。

A7-12 A7-12. TEST REAR PRESENCE R

TEST RP R The test tone is output to REAR PRESENCE R channel.
テストトーンが REAR PRESENCE R チャンネルへ出力されます。

A7-13 A7-13. TEST LFE 1

TEST LFE 1 The test tone is output to LFE 1 (SUBWOOFER 1) channel.
テストトーンが LFE 1（SUBWOOFER 1）チャンネルへ出力されます。

A7-14 A7-14. TEST LFE 2

TEST LFE 2 The test tone is output to LFE 2 (SUBWOOFER 2) channel.

RX-A3020/RX-V3073
テストトーンが LFE 2（SUBWOOFER 2）チャンネルへ出力されます。

41
 RX-A3020/RX-V3073

D1. FL CHECK D1. FL CHECK

This menu is used to check operation of the FL display. FL 表示の動作をチェックします。

FL display / FL 表示

D1-1. INITIAL DISPLAY / 初期表示

D1-2. ALL SEGMENT OFF / 全セグメント消灯

RX-A3020/RX-V3073

D1-3. ALL SEGMENT ON / 全セグメント点灯

* After check, change to next sub-menu at once.

確認後、 すみやかに次のサブメニューを選択してください。

D1-4. CHECK PATTERN 1 / チェックパターン 1

Example/ 例
Lighting on segments in lattice.
セグメント格子状点灯

D1-5. CHECK PATTERN 2 / チェックパターン 2 Short Normal

ショート 正常

Segment conditions of the FL tube is checked by 全セグメント消灯・全セグメント点灯により FL 管の

turning ON and OFF all segments. セグメントの不良を確認します。
Next, a short between segments next to each other 次に、全セグメントを交互（格子状）に点灯／消灯
is checked by turning ON and OFF all segments することで、隣り合うセグメントのショートをチェッ
alternately (in lattice). クします。
(In the above example, the segments in the second （上記の例は、上から 2 列目のセグメントがショート
row from the top are shorted.) しています。）

42
 RX-A3020/RX-V3073

Z1. ZONE TEST Z1. ZONE TEST

This menu is used to check audio signal route to ZONE 2、ZONE 3、ZONE 4 の音声信号の経路をチェッ
ZONE 2, ZONE 3, ZONE 4. クします。

Z1-1 Z1-1. AV 1
AV1 The analog audio signal input to AV 1 is output to ZONE 2/ZONE 3 OUT jack.
AV 1 に入力されたアナログ音声信号が ZONE 2/ZONE 3 OUT 端子へ出力されます。

Z1-2 Z1-2. AV 2
AV2 The analog audio signal input to AV 2 is output to ZONE 2/ZONE 3 OUT jack.
AV 2 に入力されたアナログ音声信号が ZONE 2/ZONE 3 OUT 端子へ出力されます。

Z1-3 Z1-3. AV 3
AV3 The analog audio signal input to AV 3 is output to ZONE 2/ZONE 3 OUT jack.
AV 3 に入力されたアナログ音声信号が ZONE 2/ZONE 3 OUT 端子へ出力されます。

Z1-4 Z1-4. AV 4
AV4 The 2-channel PCM signal input to AV 4 is output to HDMI OUT 2 (ZONE 4 OUT) jack.

RX-A3020/RX-V3073
AV 4 に入力された 2 チャンネル PCM 信号が HDMI OUT 2（ZONE 4 OUT）端子へ出力されます。

Z1-5 Z1-5. AUDIO 1

AUDIO1 The analog audio signal input to AUDIO 1 is output to ZONE 2 OUT and ZONE 3 OUT jacks.
AUDIO 1 に入力されたアナログ音声信号が ZONE 2 OUT、ZONE 3 OUT 端子へ出力されます。

Z1-6 Z1-6. AUDIO 2

AUDIO2 The analog audio signal input to AUDIO 2 is output to ZONE 2 OUT and ZONE 3 OUT jacks.
AUDIO 2 に入力されたアナログ音声信号が ZONE 2 OUT、ZONE 3 OUT 端子へ出力されます。

Z1-7 Z1-7. AUDIO 3

AUDIO3 The analog audio signal input to AUDIO 3 is output to ZONE 2 OUT and ZONE 3 OUT jacks.
AUDIO 3 に入力されたアナログ音声信号が ZONE 2 OUT、ZONE 3 OUT 端子へ出力されます。

Z1-8 Z1-8. AUDIO 4

AUDIO4 The analog audio signal input to AUDIO 4 is output to ZONE 2 OUT and ZONE 3 OUT jacks.
AUDIO 4 に入力されたアナログ音声信号が ZONE 2 OUT、ZONE 3 OUT 端子へ出力されます。

Z1-9 Z1-9. V-AUX

V-AUX The analog audio signal input to VIDEO AUX is output to ZONE 2 OUT and ZONE 3 OUT jacks.
VIDEO AUX に入力されたアナログ音声信号が ZONE 2 OUT、ZONE 3 OUT 端子へ出力されます。

Z1-10 Z1-10. PHONO

PHONO The analog audio signal input to PHONO is output to ZONE 2 OUT and ZONE 3 OUT jacks.
PHONO に入力されたアナログ音声信号が ZONE 2 OUT、ZONE 3 OUT 端子へ出力されます。

43
 RX-A3020/RX-V3073

U1. USB U1. USB

This menu is used to check the audio signal route from USB フラッシュメモリーからの音声信号の経路をチェッ
USB storage device. クします。

U1-1. USB FRONT 1 TRACK U1-1. USB FRONT 1 TRACK

The 1st music file stored in the USB storage USB 端子に接続された USB フラッシュメモ
device connected to the USB jack is リーに保存された音楽ファイルの 1 曲目が再
reproduced. 生されます。
* Copy 2 or more music files from PC to the ※ あらかじめ PC から USB フラッシュメモリー
root folder of the USB storage device in のルートフォルダに音楽ファイルを 2 曲以
advance. 上コピーしてください。

U1-1
USB_F 1 TRACK

U1-2. USB FRONT 2 TRACK U1-2. USB FRONT 2 TRACK

The 2nd music file stored in the USB storage USB 端子に接続された USB フラッシュメモ
device connected to the USB jack is リーに保存された音楽ファイルの 2 曲目が再
RX-A3020/RX-V3073

reproduced. 生されます。

U1-2
USB_F 2 TRACK

U1-3. USB_VBUS HIGH POWER U1-3. USB_VBUS HIGH POWER

The output current (USB_VBUS) of USB jack is USB 端子の出力電流（USB_VBUS）が最大 2.1A
output at up to 2.1A/5V. ／ 5V で出力されます。

U1-3
USB_VBUS_HPWR

44
 RX-A3020/RX-V3073

N1. NETWORK N1. NETWORK

This menu is used to check functions related to ネットワークに関連する機能をチェックします。
NETWORK. ブ ロ ー ド バ ン ド ル ー タ ー の LAN ポ ー ト と 本 機 の
Connect between LAN port of broadband router and NETWORK 端子をネットワークケーブルで接続しま
NETWORK jack of this unit with a network cable. す。
* When the network condition varies while sub-menu ※ サブメニュー表示中にネットワークの状態が変わ
is displayed (e.g., the network is deactivated ると（たとえばネットワークが一時切れるなど）
once), the correct result will not be displayed. 正しい結果が表示されません。
In that case, once turn off the power to this unit, その場合、一度本機の電源を切り、ダイアグを再
then start up the self-diagnostic function again 起動して本メニューを選択します。
and select this menu.

N1-1. IP ADDRESS CHECK N1-1. IP ADDRESS CHECK

This menu is used to check that IP address IP アドレスが取得されていることをチェック
can be obtained. します。

N1-1
IP AD CHK:OK
OK: Connected (IP address obtained)

RX-A3020/RX-V3073
接続（IP アドレス取得完了）
NG: No traffic / Disconnected
通信不能 ／ 接続が切れている

N1-2. MAC ADDRESS CHECK N1-2. MAC ADDRESS CHECK

This menu is used to check that MAC address MAC アドレスが書き込まれていることを
is written. チェックします。

N1-2
MAC AD CHK:OK
OK: Normal / 正常
NG: Unwritten / 書き込まれていない

N1-3. LINE NOISE 100 MDI N1-3. LINE NOISE 100 MDI
Not for service. サービスでは使用しません。

N1-3
LN MDI 100

N1-4. LINE NOISE 100 MDIX N1-4. LINE NOISE 100 MDIX
Not for service. サービスでは使用しません。

N1-4
LN MDIX 100

45
 RX-A3020/RX-V3073

N1-5. LINE NOISE 10 MDI N1-5. LINE NOISE 10 MDI

Not for service. サービスでは使用しません。

N1-5
LN MDI 10

N1-6. LINE NOISE 10 MDIX N1-6. LINE NOISE 10 MDIX

Not for service. サービスでは使用しません。

N1-6
LN MDIX 10

N1-7. EXT TEST N1-7. EXT TEST

Transmission/reception of the NETWORK jack NETWORK ポートの送受信テストを行います。
is checked. 電源を切った状態で、下図のように NETWORK
With the power turned off, short the pins of the 端子のピンをショートさせます。
RX-A3020/RX-V3073

NETWORK jack as shown in the figure below. ダイアグを起動して本メニューを選択します。

Start up the self-diagnostic function and select 送受信テストを行い、その結果が表示されま
this menu. す。
Transmission/reception test is executed and
its result is displayed.

Note: Be sure to return the shorted pins 注意： 検査後、ショートしたピンを必ず元の

to their original condition after 状態に戻してください。
executing this test.

N1-7
8 7 6 5 4 3 2 1
EXT TEST:OK
OK: Normal / 正常
NG: Abnormal / 異常
--: Checking / チェック中

NETWORK jack

N1-8. MAC ADDRESS N1-8. MAC ADDRESS

Written MAC address is displayed. 書き込まれている MAC アドレスが表示されま
す。

N1-8
00A0DExxxxxx

46
 RX-A3020/RX-V3073

C1. DIGITAL P.C.B. CHECK C1. DIGITAL P.C.B. CHECK

This menu is used to check the communication and DIGITAL P.C.B. 上の各デバイス間の通信とバスライン
bus line connection between devices on DIGITAL 接続をチェックします。
P.C.B.

C1-1. ALL C1-1. ALL

Not for service. サービスでは使用しません。

C1-1
ALL:NG Ext.JIG
When test result using the “C1-9. RS-232C LOOP BACK
CHECK” menu is NG, “Ext. JIG” is displayed.
C1-9. RS-232C LOOP BACK CHECK メニューのテスト結果が
NG の場合、「Ext. JIG」が表示されます。

OK: No error detected / 不良検出なし

NG: An error is detected / 不良検出あり
--: Checking / チェック中

RX-A3020/RX-V3073
C1-2. BUS FLASH ROM C1-2. BUS FLASH ROM
FLASH ROM (IC75)’s reading/writing are FLASH ROM（IC75）の読み出し／書き込みを
checked. チェックします。

C1-2
BUS_FROM:OK
OK: No error detected / 不良検出なし
NG: An error is detected / 不良検出あり
--: Checking / チェック中

C1-3. BUS FPGA C1-3. BUS FPGA

Communication and bus line connection マイコン（IC79）と FPGA（IC50）間の通信と
between microprocessor (IC79) and FPGA バスライン接続をチェックします。
(IC50) are checked.

C1-3
BUS_FPGA:OK
OK: No error detected / 不良検出なし
NG: An error is detected / 不良検出あり
--: Checking / チェック中

47
 RX-A3020/RX-V3073

C1-4. I2C C1-4. I2C

The I2C (Inter integrated circuit) bus line I2C（Inter integrated circuit）バスライン接続
connection is checked. をチェックします。

C1-4
0000000 000 0 0 : No error detected / 不良検出なし
1 : An error is detected / 不良検出あり

Error detection of Front HDMI equalizer (IC30) / フロント HDMI IC（IC30）の不良検出

Error detection of VIDEO encoder (IC20) / ビデオエンコーダー（IC20）の不良検出
Error detection of VIDEO P.C.B. / VIDEO P.C.B. の不良検出
Error detection of Video decoder (IC21) / ビデオデコーダー（IC21）の不良検出
Error detection of HDMI receiver 2 (IC4) / HDMI レシーバー 2（IC4）の不良検出
Error detection of VIDEO processor (IC41) / ビデオプロセッサー（IC41）の不良検出
Error detection of HDMI transmitter 2 (IC62) / HDMI トランスミッター 2（IC62）の不良検出
Error detection of HDMI transmitter 1 (IC61) / HDMI トランスミッター 1（IC61）の不良検出
Error detection of HDMI receiver 1 (IC3) / HDMI レシーバー 1（IC3）の不良検出
Error detection of HDMI switcher 2 (IC2) / HDMI スイッチャー 2（IC2）の不良検出
Error detection of HDMI switcher 1 (IC1) / HDMI スイッチャー 1（IC1）の不良検出
RX-A3020/RX-V3073

C1-5. FPGA RAM C1-5. FPGA RAM

SDRAM (IC53)’s reading/writing are checked. SDRAM（IC53）の読み出し／書き込みをチェッ
クします。

C1-5
FPGA_RAM:OK
OK: No error detected / 不良検出なし
NG: An error is detected / 不良検出あり

C1-6. BUS DIR1 C1-6. BUS DIR1

Communication and bus line connection マイコン（IC79）と DIR1（IC900）間の通信と
between microprocessor (IC79) and DIR1 バスライン接続をチェックします。
(IC900) are checked.

C1-6
DIR1 BUS:OK
OK: No error detected / 不良検出なし
NG: An error is detected / 不良検出あり

C1-7. BUS DSP1 C1-7. BUS DSP1

Communication and bus line connection マイコン（IC79）と DSP1（IC911）間の通信
between microprocessor (IC79) and DSP1 とバスライン接続をチェックします。
(IC911) are checked.

C1-7
DSP1 BUS:OK
OK: No error detected / 不良検出なし
NG: An error is detected / 不良検出あり
48
 RX-A3020/RX-V3073

C1-8. EEPROM C1-8. EEPROM

EEPROM (IC78)'s reading is checked. EEPROM（IC78）の読み出しをチェックします。

C1-8
EEPROM:OK
OK: No error detected / 不良検出なし
NG: An error is detected / 不良検出あり

C1-9. RS-232C DATA CHECK C1-9. RS-232C DATA CHECK

Not for service. サービスでは使用しません。

C1-9
232C DATA:NG

RX-A3020/RX-V3073
C1-10. BUS DIR2 C1-10. BUS DIR2
Communication and bus line connection マイコン（IC79）と DIR2（IC903）間の通信と
between microprocessor (IC79) and DIR2 バスライン接続をチェックします。
(IC903) are checked.

C1-6
DIR2 BUS:OK
OK: No error detected / 不良検出なし
NG: An error is detected / 不良検出あり

C1-11. BUS DSP2 C1-11. BUS DSP2

Communication and bus line connection マイコン（IC79）と DSP2（IC920）間の通信
between microprocessor (IC79) and DSP2 とバスライン接続をチェックします。
(IC920) are checked.

C1-11
DSP2 BUS:OK
OK: No error detected / 不良検出なし
NG: An error is detected / 不良検出あり

49
 RX-A3020/RX-V3073

C2. NETWORK IC CHECK C2. NETWORK IC CHECK

This menu is used to check the communication and bus ネットワークに関連する各デバイス間の通信とバス
line connection between devices related to network. ラインの接続をチェックします。

C2-1. ALL C2-1. ALL

The synthetic judgment result of sub-menu サブメニュー C2-2 ∼ C2-5 の総合判定結果が
C2-2 to C2-5 is displayed. 表示されます。

C2-1
ALL:OK Ext.JIG
When test result using the “C2-2. LINK CHECK” menu is
NG, the sub-menu C2-2 is NG, “Ext. JIG” is displayed.
C2-2. LINK CHECK メニューのテスト結果が NG の場合、
「Ext. JIG」が表示されます。

OK: No error detected / 不良検出なし

NG: An error is detected / 不良検出あり
--: Checking / チェック中
RX-A3020/RX-V3073

C2-2. LINK CHECK C2-2. LINK CHECK

LAN cable connection is checked. LAN ケーブルの接続状態をチェックします。
Connect between NETWORK jack of this unit 本機の NETWORK 端子とブロードバンドルー
and LAN port of broadband router with a ターの LAN ポートをネットワークケーブルで
network cable. 接続します。
* When the network condition varies while ※ サブメニュー表示中にネットワークの状態
sub-menu is displayed (e.g., the network が変わると（たとえばネットワークが一時
is deactivated once), the correct result will 切れるなど）正しい結果が表示されません。
not be displayed. In that case, once turn その場合、一度本機の電源を切り、ダイア
off the power to this unit, then start up the グを再起動して本メニューを選択します。
self-diagnostic function again and select
this menu.

C2-2
LINK CHK:OK
OK: Normal / 正常
NG: Disconnected / 接続が切れている
--: Checking / チェック中

C2-3. PHY (Ethernet PHYceiver) TEST C2-3. PHY（Ethernet PHYceiver）TEST

Communication and bus line connection PHY（IC955）と NETWORK マイコン（IC951）
between PHY (IC955) and NETWORK 間の通信とバスライン接続をチェックします。
microprocessor (IC951) are checked.

C2-3
PHY TEST:OK
OK: No error detected / 不良検出なし
NG: An error is detected / 不良検出あり
--: Checking / チェック中

50
 RX-A3020/RX-V3073

C2-4. BUS RAM C2-4. BUS RAM

Communication and bus line connection SDRAM（IC952）と NETWORK マイコン（IC951）
between SDRAM (IC952) and NETWORK 間の通信とバスライン接続をチェックします。
microprocessor (IC951) are checked.

C2-4
RAM BUS:OK
OK: No error detected / 不良検出なし
NG: An error is detected / 不良検出あり
--: Checking / チェック中

C2-5. APL (Apple) ID CHECK C2-5. APL（Apple）ID CHECK

Apple authentication IC (IC956) device ID is Apple 認証 IC（IC956）のデバイス ID をチェッ
checked. クします。

C2-5

RX-A3020/RX-V3073
APL ID:OK
OK: No error detected / 不良検出なし
NG: An error is detected / 不良検出あり
--: Checking / チェック中

51
 RX-A3020/RX-V3073

V1. ANALOG VIDEO CHECK V1. ANALOG VIDEO CHECK

This menu is used to check the analog video signal アナログ映像信号の経路をチェックします。
route.

V1-1. ANALOG BYPASS V1-1. ANALOG BYPASS

The video signal is converted and output as 映像信号が以下のように出力されます。
shown below.

V1-1
ANALOG BYPASS

ANALOG BYPASS
HDMI IN HDMI OUT
DIGITAL DIGITAL
DIGITAL
IC3 IC61
IC50
HDMI HDMI
FPGA
Receiver Transmitter

Component In DIGITAL DIGITAL Component Out

IC21 IC20
MUTE
VIDEO VDEC_N_RST VIDEO
PCB PCB
Decoder Encoder
VIDEO VIDEO
IC305 IC305
NJW1327 NJW1327
RX-A3020/RX-V3073

S Video In S Video Out

Composite In Composite Out

V1-2. DIGITAL BYPASS V1-2. DIGITAL BYPASS

The video signal is converted and output as 映像信号が以下のように変換され、出力され
shown below. ます。

V1-2
DIGITAL BYPASS

DIGITAL BYPASS
HDMI IN HDMI OUT
DIGITAL DIGITAL
DIGITAL
IC3 IC61
IC50
HDMI HDMI
FPGA
Receiver Transmitter

Component In DIGITAL DIGITAL Component Out

IC21 IC20
MUTE
VIDEO VDEC_N_RST VIDEO
PCB PCB
Decoder Encoder
VIDEO VIDEO
IC305 IC305
NJW1327 NJW1327

S Video In S Video Out

Composite In Composite Out

52
 RX-A3020/RX-V3073

V1-3. ZONE BYPASS V1-3. ZONE BYPASS

The video signal is converted and output as 映像信号が以下のように変換され、出力され
shown below. ます。

V1-3
ZONE BYPASS
ZONE BYPASS
HDMI IN HDMI OUT
DIGITAL DIGITAL
DIGITAL
IC3 IC61
IC50
HDMI HDMI
FPGA
Receiver Transmitter

Component In DIGITAL DIGITAL Component Out

IC21 IC20
VIDEO VIDEO
PCB PCB
Decoder Encoder
VIDEO VIDEO
IC305 IC305
NJW1327 NJW1327

S Video In S Video Out

Composite In Composite Out

* MON/ZONE OUTPUT is selectable different from AV-OUT.

RX-A3020/RX-V3073
V1-4. MUTE CHECK V1-4. MUTE CHECK
The video signal is muted. 映像信号がミュートされます。

V1-4
MUTE CHECK
MUTE CHECK
HDMI IN HDMI OUT
DIGITAL DIGITAL
DIGITAL
IC3 IC61
IC50
HDMI HDMI
FPGA
Receiver Transmitter
MUTE
Component In DIGITAL DIGITAL Component Out
IC21 IC20
VIDEO VIDEO
PCB PCB
Decoder Encoder
VIDEO VIDEO
IC305 IC305
NJW1327 NJW1327

S Video In S Video Out

Composite In Composite Out

V1-5. TEST PATTERN V1-5. TEST PATTERN

Not for service. サービスでは使用しません。

V1-5
TEST PATTERN

V1-6. VIDEO INFORMATION V1-6. VIDEO INFORMATION

The information of input analog video signals 入力されているアナログ映像信号の情報が表
is displayed. 示されます。

V1-6
VID IN:480i60
53
 RX-A3020/RX-V3073

V2. DIGITAL VIDEO CHECK V2. DIGITAL VIDEO CHECK

This menu is used to check the digital video signal デジタル映像信号の経路をチェックします。
route.

V2-1. LOOPBACK TEST 1 V2-1. LOOPBACK TEST 1

Execute the test for all HDMI IN jacks by 下記の手順を繰り返して全 HDMI IN 端子のテ
repeating the procedure below. ストを行います。
1. Select sub-menu other than V2-1. 1. V2-1 以外のサブメニューを選択します。
2. Connect between any of the HDMI IN jacks 2. HDMI IN 端子の 1 つと HDMI OUT1 端子を
and HDMI OUT 1 jack with an HDMI cable. HDMI ケーブルで接続します。
3. Select V2-1. The test result is displayed in a 3. V2-1 を選択します。数秒後にテスト結果が
few seconds. 表示されます。

V2-1
TEST1:OK
OK: No error detected / 不良検出なし
NG: An error is detected / 不良検出あり
--: Checking / 検出中
RX-A3020/RX-V3073

HDMI Cable for Loopback

CB1 CB1 CB1 CB1 CB1 CB1 CB1 CB30 CB62 CB61
Front-HDMI-Board

HDMI HDMI HDMI HDMI HDMI HDMI HDMI HDMI IN HDMI HDMI
IN7 IN6 IN5 IN4 IN3 IN2 IN1 Front OUT2 OUT1

IC30
HDMI EQUALIZER
TMDS261 IC53
128Mbit IC62 IC61
IC2 IC1 SDRAM HDMI HDMI
HDMI SWITCHER 2 HDMI SWITCHER 1 TRANSMITTER 2 TRANSMITTER 1
ADV7630 ADV7630 Sii9136-3 Sii9136-3

IC4 IC50
HDMI RECEIVER 2 FPGA
ADV7619 EP4CE15F23C6N
IC3
HDMI RECEIVER 1
ADV7619

IC41
Scaler
VHD1900

IC21 IC20
VIDEO DECODER VIDEO ENCODER
ADV7181C ADV7172

54
 RX-A3020/RX-V3073

V2-2. LOOPBACK TEST 2 V2-2. LOOPBACK TEST 2

HDMI receiver 1 IC (IC3) is checked. HDMI レシーバー１IC（IC3）をチェックします。
1. Select sub-menu other than V2-2. 1. V2-2 以外のサブメニューを選択します。
2. Connect between any of the HDMI IN jacks 2. HDMI IN 端子の 1 つと HDMI OUT 端子を
and HDMI OUT jack with an HDMI cable. HDMI ケーブルで接続します。
3. Select the input source corresponding 3. 接続した HDMI IN 端子に合わせて入力ソー
to the connected HDMI IN jack by using スを INPUT ツマミで選択します。
“INPUT” knob. 4. V2-2 を選択します。数秒後にテスト結果が
4. Select V2-2. The test result is displayed in a 表示されます。
few seconds.

Select the input source Result

HDMI1 V-AUX V2-2

TEST2:OK
OK: No error detected /
不良検出なし
NG: An error is detected /
不良検出あり
--: Checking / 検出中

RX-A3020/RX-V3073
HDMI Cable for Loopback

CB1 CB1 CB1 CB1 CB1 CB1 CB1 CB30 CB62 CB61
Front-HDMI-Board

HDMI HDMI HDMI HDMI HDMI HDMI HDMI HDMI IN HDMI HDMI
IN7 IN6 IN5 IN4 IN3 IN2 IN1 Front OUT2 OUT1

IC30
HDMI EQUALIZER
TMDS261 IC53
128Mbit IC62 IC61
IC2 IC1 SDRAM HDMI HDMI
HDMI SWITCHER 2 HDMI SWITCHER 1 TRANSMITTER 2 TRANSMITTER 1
ADV7630 ADV7630 Sii9136-3 Sii9136-3

IC4 IC50
HDMI RECEIVER 2 FPGA
ADV7619 EP4CE15F23C6N 4K test pattern
IC3
HDMI RECEIVER 1
ADV7619

IC41
Scaler
VHD1900

IC21 IC20
VIDEO DECODER VIDEO ENCODER
ADV7181C ADV7172

55
 RX-A3020/RX-V3073

V2-3. LOOPBACK TEST 3 V2-3. LOOPBACK TEST 3

HDMI transmitter 1 IC (IC61) is checked. HDMI トランスミッター 1 IC（IC61）をチェッ
クします。
1. Select sub-menu other than V2-3.
2. Connect between any of the HDMI IN jacks 1. V2-3 以外のサブメニューを選択します。
and HDMI OUT 1 jack with an HDMI cable. 2. HDMI IN 端子の 1 つと HDMI OUT1 端子を
3. Select the input source corresponding HDMI ケーブルで接続します。
to the connected HDMI IN jack by using 3. 接続した HDMI IN 端子に合わせて入力ソー
“INPUT” knob. スを INPUT ツマミで選択します。
4. Select V2-3. The test result is displayed in a 4. V2-3 を選択します。数秒後にテスト結果が
few seconds. 表示されます。

Select the input source Result

HDMI1 V-AUX V2-3

TEST3:OK
OK: No error detected /
不良検出なし
NG: An error is detected /
不良検出あり
--: Checking / 検出中
RX-A3020/RX-V3073

HDMI Cable for Loopback

CB1 CB1 CB1 CB1 CB1 CB1 CB1 CB30 CB62 CB61
Front-HDMI-Board

HDMI HDMI HDMI HDMI HDMI HDMI HDMI HDMI IN HDMI HDMI
IN7 IN6 IN5 IN4 IN3 IN2 IN1 Front OUT2 OUT1

IC30
HDMI EQUALIZER
TMDS261 IC53
128Mbit IC62 IC61
IC2 IC1 SDRAM HDMI HDMI
HDMI SWITCHER 2 HDMI SWITCHER 1 TRANSMITTER 2 TRANSMITTER 1
ADV7630 ADV7630 Sii9136-3 Sii9136-3

IC4 IC50
HDMI RECEIVER 2 FPGA
ADV7619 EP4CE15F23C6N 1080@60Hz 12bit
IC3
HDMI RECEIVER 1
ADV7619

IC41
Scaler
VHD1900

IC21 IC20
VIDEO DECODER VIDEO ENCODER
ADV7181C ADV7172

56
 RX-A3020/RX-V3073

V2-4. LOOPBACK TEST 4 V2-4. LOOPBACK TEST 4

HDMI transmitter 2 IC (IC64) is checked. HDMI トランスミッター２ IC（IC64）をチェッ
クします。
1. Select sub-menu other than V2-4.
2. Connect between any of the HDMI IN jacks 1. V2-4 以外のサブメニューを選択します。
and HDMI OUT 2 jack with an HDMI cable. 2. HDMI IN 端子の 1 つと HDMI OUT2 端子を
3. Select the input source corresponding HDMI ケーブルで接続します。
to the connected HDMI IN jack by using 3. 接続した HDMI IN 端子に合わせて入力ソー
“INPUT” knob. スを INPUT ツマミで選択します。
4. Select V2-4. The test result is displayed in a 4. V2-4 を選択します。数秒後にテスト結果が
few seconds. 表示されます。

Select the input source Result

HDMI1 V-AUX V2-4

TEST4:OK
OK: No error detected /
不良検出なし
NG: An error is detected /
不良検出あり
--: Checking / 検出中

RX-A3020/RX-V3073
HDMI Cable for Loopback

CB1 CB1 CB1 CB1 CB1 CB1 CB1 CB30 CB62 CB61
Front-HDMI-Board

HDMI HDMI HDMI HDMI HDMI HDMI HDMI HDMI IN HDMI HDMI
IN7 IN6 IN5 IN4 IN3 IN2 IN1 Front OUT2 OUT1

IC30
HDMI EQUALIZER
TMDS261 IC53
128Mbit IC62 IC61
IC2 IC1 SDRAM HDMI HDMI
HDMI SWITCHER 2 HDMI SWITCHER 1 TRANSMITTER 2 TRANSMITTER 1
ADV7630 ADV7630 Sii9136-3 Sii9136-3

IC4 IC50
HDMI RECEIVER 2 FPGA
ADV7619 EP4CE15F23C6N 1080@60Hz 12bit
IC3
HDMI RECEIVER 1
ADV7619

IC41
Scaler
VHD1900

IC21 IC20
VIDEO DECODER VIDEO ENCODER
ADV7181C ADV7172

57
 RX-A3020/RX-V3073

V2-5. LOOPBACK TEST 5 V2-5. LOOPBACK TEST 5

Scaler IC (IC41) is checked. Scaler IC（IC41）をチェックします。
1. Select sub-menu other than V2-5. 1. V2-5 以外のサブメニューを選択します。
2. Connect between any of the HDMI IN jacks 2. HDMI IN 端子の 1 つと HDMI OUT2 端子を
and HDMI OUT 2 jack with an HDMI cable. HDMI ケーブルで接続します。
3. Select the input source corresponding 3. 接続した HDMI IN 端子に合わせて入力ソー
to the connected HDMI IN jack by using スを INPUT ツマミで選択します。
“INPUT” knob. 4. V2-5 を選択します。数秒後にテスト結果が
4. Select V2-5. The test result is displayed in a 表示されます。
few seconds.

Select the input source Result

HDMI1 V-AUX V2-5

TEST5:OK
OK: No error detected /
不良検出なし
NG: An error is detected /
不良検出あり
--: Checking / 検出中
RX-A3020/RX-V3073

HDMI Cable for Loopback

CB1 CB1 CB1 CB1 CB1 CB1 CB1 CB30 CB62 CB61
Front-HDMI-Board

HDMI HDMI HDMI HDMI HDMI HDMI HDMI HDMI IN HDMI HDMI
IN7 IN6 IN5 IN4 IN3 IN2 IN1 Front OUT2 OUT1

IC30
HDMI EQUALIZER
TMDS261 IC53
128Mbit IC62 IC61
IC2 IC1 SDRAM HDMI HDMI
HDMI SWITCHER 2 HDMI SWITCHER 1 TRANSMITTER 2 TRANSMITTER 1
ADV7630 ADV7630 Sii9136-3 Sii9136-3

IC4 IC50
HDMI RECEIVER 2 FPGA
ADV7619 EP4CE15F23C6N 1080@60Hz 12bit
IC3
HDMI RECEIVER 1
ADV7619

IC41
Scaler
VHD1900
IC21 IC20
VIDEO DECODER VIDEO ENCODER
ADV7181C ADV7172

58
 RX-A3020/RX-V3073

V2-6. LOOPBACK TEST 6 V2-6. LOOPBACK TEST 6

HDMI receiver 2 IC (IC3) is checked. HDMI レシーバー 2 IC（IC3）をチェックします。
1. Select sub-menu other than V2-6. 1. V2-6 以外のサブメニューを選択します。
2. Connect between any of the HDMI IN jacks 2. HDMI IN 端子の 1 つと HDMI OUT2 端子を
and HDMI OUT 2 jack with an HDMI cable. HDMI ケーブルで接続します。
3. Select the input source corresponding 3. 接続した HDMI IN 端子に合わせて入力ソー
to the connected HDMI IN jack by using スを INPUT ツマミで選択します。
“INPUT” knob. 4. V2-6 を選択します。数秒後にテスト結果が
4. Select V2-6. The test result is displayed in a 表示されます。
few seconds.

Select the input source Result

HDMI1 V-AUX V2-6

TEST6:OK
OK: No error detected /
不良検出なし
NG: An error is detected /
不良検出あり
--: Checking / 検出中

RX-A3020/RX-V3073
HDMI Cable for Loopback

CB1 CB1 CB1 CB1 CB1 CB1 CB1 CB30 CB62 CB61
Front-HDMI-Board

HDMI HDMI HDMI HDMI HDMI HDMI HDMI HDMI IN HDMI HDMI
IN7 IN6 IN5 IN4 IN3 IN2 IN1 Front OUT2 OUT1

IC30
HDMI EQUALIZER
TMDS261 IC53
128Mbit IC62 IC61
IC2 IC1 SDRAM HDMI HDMI
HDMI SWITCHER 2 HDMI SWITCHER 1 TRANSMITTER 2 TRANSMITTER 1
ADV7630 ADV7630 Sii9136-3 Sii9136-3

IC4 IC50
HDMI RECEIVER 2 FPGA
ADV7619 EP4CE15F23C6N 4K test pattern
IC3
HDMI RECEIVER 1
ADV7619

IC41
Scaler
VHD1900

IC21 IC20
VIDEO DECODER VIDEO ENCODER
ADV7181C ADV7172

59
 RX-A3020/RX-V3073

V2-7. HDMI REPEAT V2-7. HDMI REPEAT

The video/audio signals input to HDMI IN jack HDMI IN 端子へ入力された映像信号と音声信
are output to HDMI OUT jack. 号が HDMI OUT 端子へ出力されます。

V2-7
HDMI REPEAT **
The Deep Color video signals is input, “30” bit or
“36” bit is displayed.
Deep Color 映像信号を入力すると、 30 bit または
36 bit が表示されます。

TV

HDMI
HDMI output
HDMI

BD/DVD player

CB1 CB1 CB1 CB1 CB1 CB1 CB1 CB30 CB62 CB61
Front-HDMI-Board

HDMI HDMI HDMI HDMI HDMI HDMI HDMI HDMI IN HDMI HDMI
IN7 IN6 IN5 IN4 IN3 IN2 IN1 Front OUT2 OUT1
RX-A3020/RX-V3073

IC30
HDMI EQUALIZER
TMDS261 IC53
128Mbit IC62 IC61
IC2 IC1 SDRAM HDMI HDMI
HDMI SWITCHER 2 HDMI SWITCHER 1 TRANSMITTER 2 TRANSMITTER 1
ADV7630 ADV7630 Sii9136-3 Sii9136-3

IC4 IC50
HDMI RECEIVER 2 FPGA
ADV7619 EP4CE15F23C6N
IC3
HDMI RECEIVER 1
ADV7619

IC41
Scaler
VHD1900

IC21 IC20
VIDEO DECODER VIDEO ENCODER
ADV7181C ADV7172

60
 RX-A3020/RX-V3073

V2-8. DIGITAL CVBS V2-8. DIGITAL CVBS

The video (CVBS) signal is converted and 映像信号が以下のように変換され、出力され
output as shown below. ます。

V2-8 TV

DIGITAL CVBS HDMI

CB1 CB1 CB1 CB1 CB1 CB1 CB1 CB30 CB62 CB61

Front-HDMI-Board
HDMI HDMI HDMI HDMI HDMI HDMI HDMI HDMI IN HDMI HDMI
IN7 IN6 IN5 IN4 IN3 IN2 IN1 Front OUT2 OUT1

IC30
HDMI EQUALIZER
TMDS261 IC53
128Mbit IC62 IC61
IC2 IC1 SDRAM HDMI HDMI
HDMI SWITCHER 2 HDMI SWITCHER 1 TRANSMITTER 2 TRANSMITTER 1
ADV7630 ADV7630 Sii9136-3 Sii9136-3

IC4 IC50
HDMI RECEIVER 2 FPGA

RX-A3020/RX-V3073
ADV7619 EP4CE15F23C6N
IC3
HDMI RECEIVER 1
Video output ADV7619
VIDEO

IC41
Scaler
VHD1900
BD/DVD player
IC21 IC20 Y,CbCr
VIDEO DECODER VIDEO ENCODER Y,C
CVBS ADV7181C ADV7172 CVBS

V2-9. DIGITAL Y/C V2-9. DIGITAL Y/C

The s-video (Y, C) signal is converted and 映像信号が以下のように変換され、出力され
output as shown below. ます。

V2-9 TV

DIGITAL Y/C HDMI

CB1 CB1 CB1 CB1 CB1 CB1 CB1 CB30 CB62 CB61
Front-HDMI-Board

HDMI HDMI HDMI HDMI HDMI HDMI HDMI HDMI IN HDMI HDMI
IN7 IN6 IN5 IN4 IN3 IN2 IN1 Front OUT2 OUT1

IC30
HDMI EQUALIZER
TMDS261 IC53
128Mbit IC62 IC61
IC2 IC1 SDRAM HDMI HDMI
HDMI SWITCHER 2 HDMI SWITCHER 1 TRANSMITTER 2 TRANSMITTER 1
ADV7630 ADV7630 Sii9136-3 Sii9136-3

IC4 IC50
HDMI RECEIVER 2 FPGA
ADV7619 EP4CE15F23C6N
IC3
S-video output HDMI RECEIVER 1
S-VIDEO ADV7619

IC41
Scaler
VHD1900
BD/DVD player
IC21 IC20 Y,CbCr
Y,C VIDEO DECODER VIDEO ENCODER Y,C
ADV7181C ADV7172 CVBS

61
 RX-A3020/RX-V3073

V2-10. DIGITAL COMPONENT V2-10. DIGITAL COMPONENT

The component video (Y, Cb, Cr) signal is 映像信号が以下のように変換され、出力され
converted and output as shown below. ます。

V2-10
DIGITAL Cmp

TV

HDMI

CB1 CB1 CB1 CB1 CB1 CB1 CB1 CB30 CB62 CB61

Front-HDMI-Board
HDMI HDMI HDMI HDMI HDMI HDMI HDMI HDMI IN HDMI HDMI
IN7 IN6 IN5 IN4 IN3 IN2 IN1 Front OUT2 OUT1

IC30
HDMI EQUALIZER
TMDS261 IC53
128Mbit IC62 IC61
IC2 IC1 SDRAM HDMI HDMI
TRANSMITTER 2 TRANSMITTER 1
RX-A3020/RX-V3073

HDMI SWITCHER 2 HDMI SWITCHER 1

ADV7630 ADV7630 Sii9136-3 Sii9136-3

IC4 IC50
Component video output HDMI RECEIVER 2 FPGA
COMPONENT ADV7619
IC3 EP4CE15F23C6N
HDMI RECEIVER 1
ADV7619

IC41
Scaler
BD/DVD player VHD1900

Y,CbCr IC21 IC20 Y,CbCr

VIDEO DECODER VIDEO ENCODER Y,C
ADV7181C ADV7172 CVBS

62
 RX-A3020/RX-V3073

V2-11. DIGITAL COMPONENT SC V2-11. DIGITAL COMPONENT SC

The component video (Y, Cb, Cr) signal is 映像信号が以下のように変換され、出力され
converted and output as shown below. ます。
HDMI video output up-scaling: アップスケーリング：
480i/p, 576i/p only => 1080p 480i/p、576i/p => 1080p

V2-11
DIGITAL Cmp SC

TV

HDMI

CB1 CB1 CB1 CB1 CB1 CB1 CB1 CB30 CB62 CB61
HDMI HDMI HDMI HDMI HDMI HDMI HDMI Front-HDMI-Board HDMI IN HDMI HDMI
IN7 IN6 IN5 IN4 IN3 IN2 IN1 Front OUT2 OUT1

IC30

RX-A3020/RX-V3073
HDMI EQUALIZER
TMDS261 IC53
128Mbit IC62 IC61
IC2 IC1 SDRAM HDMI HDMI
HDMI SWITCHER 2 HDMI SWITCHER 1 TRANSMITTER 2 TRANSMITTER 1
ADV7630 ADV7630 Sii9136-3 Sii9136-3

IC4 IC50
Component output HDMI RECEIVER 2 FPGA
COMPONENT ADV7619
IC3 EP4CE15F23C6N
HDMI RECEIVER 1
ADV7619

IC41
Scaler
BD/DVD player VHD1900

Y,CbCr IC21 IC20 Y,CbCr

VIDEO DECODER VIDEO ENCODER Y,C
ADV7181C ADV7172 CVBS

63
 RX-A3020/RX-V3073

V2-12. GUI-VIDEO OUT V2-12. GUI-VIDEO OUT

The GUI is output from FPGA (IC50 on DIGITAL FPGA（DIGITAL P.C.B. の IC50）から GUI が出
P.C.B.). 力されます。

V2-12
GUI-VIDEO OUT

TV

HDMI

CB1 CB1 CB1 CB1 CB1 CB1 CB1 CB30 CB62 CB61

Front-HDMI-Board
HDMI HDMI HDMI HDMI HDMI HDMI HDMI HDMI IN HDMI HDMI
IN7 IN6 IN5 IN4 IN3 IN2 IN1 Front OUT2 OUT1

IC30
HDMI EQUALIZER
TMDS261 IC53
128Mbit IC62 IC61
IC2 IC1 SDRAM HDMI HDMI
RX-A3020/RX-V3073

HDMI SWITCHER 2 HDMI SWITCHER 1 TRANSMITTER 2 TRANSMITTER 1

ADV7630 ADV7630 Sii9136-3 Sii9136-3

IC50
FPGA
IC4 EP4CE15F23C6N
HDMI RECEIVER 2
ADV7619
IC3 GUI
HDMI RECEIVER 1
ADV7619

IC41
Scaler
VHD1900

IC21 IC20 Y,CbCr

VIDEO DECODER VIDEO ENCODER Y,C
ADV7181C ADV7172 CVBS

64
 RX-A3020/RX-V3073

V3. TEST PATTERN V3. TEST PATTERN

The GUI is output to HDMI OUT jack with its resolution GUI が、以下のように解像度が変換されて、HDMI
converted as shown below. OUT 端子へ出力されます。

TV

HDMI

CB1 CB1 CB1 CB1 CB1 CB1 CB1 CB30 CB62 CB61

Front-HDMI-Board
HDMI HDMI HDMI HDMI HDMI HDMI HDMI HDMI IN HDMI HDMI
IN7 IN6 IN5 IN4 IN3 IN2 IN1 Front OUT2 OUT1

IC30
HDMI EQUALIZER
TMDS261 IC53
128Mbit IC62 IC61
IC2 IC1 SDRAM HDMI HDMI
HDMI SWITCHER 2 HDMI SWITCHER 1 TRANSMITTER 2 TRANSMITTER 1
ADV7630 ADV7630 Sii9136-3 Sii9136-3

IC50
FPGA
IC4 EP4CE15F23C6N
HDMI RECEIVER 2

RX-A3020/RX-V3073
ADV7619
IC3 GUI
HDMI RECEIVER 1
ADV7619

IC41
Scaler
VHD1900

IC21 IC20 Y,CbCr

VIDEO DECODER VIDEO ENCODER Y,C
ADV7181C ADV7172 CVBS

V3-1. 480i V3-2. 480p V3-3. 720p 60Hz V3-4. 1080i 60Hz
V3-1 V3-2 V3-3 V3-4
480i 480p 720p 60 1080i 60

V3-5. 1080p 60Hz V3-6. 576i V3-7. 576p V3-8. 720p 50Hz
V3-5 V3-6 V3-7 V3-8
1080p 60 576i 576p 720p 50

V3-9. 1080i 50Hz V3-10. 1080p 50Hz V3-11. 1080p 24Hz V3-12. 1080p 24Hz 3D/FP
V3-9 V3-10 V3-11 V3-12
1080i 50 1080p 50 1080p 24 1080p 24 3D/FP
(FP: Frame Packing)

V3-13. 720p 60Hz 3D/FP V3-14. 720p 50Hz 3D/FP V3-15. 1080i 60Hz 3D/FP V3-16. 1080i 60Hz 3D/SS
V3-13 V3-14 V3-15 V3-16
720p 60 3D/FP 720p 50 3D/FP 1080i 60 3D/FP 1080i 60 3D/SS
(SS: Side-by-Side)

V3-17. 1080i 50Hz 3D/SS V3-18. 720p 60Hz 3D/TB V3-19. 720p 50Hz 3D/TB V3-20. 1080p 24Hz 3D/TB
V3-17 V3-18 V3-19 V3-20
1080i 50 3D/SS 720p 60 3D/TB 720p 50 3D/TB 1080p 24 3D/TB
(TB: Top-and-Bottom)

V3-21. 4k 24Hz
V3-21
4k 24
(4k: Digital cinema 4K, Resolution 3996 × 2160p)

65
 RX-A3020/RX-V3073

T1. POWER T1. POWER

This menu is used to display the operating time and 本機の動作時間、動作回数が表示されます。
operation frequency of this unit.
※ ダイアグ中の動作時間、動作回数は保存されませ
* The operating time and operation frequency during ん。
the self-diagnostic function mode will not be stored.

T1-1. OPERATING TIME T1-1. OPERATING TIME

The operating time of this unit is displayed. 本機の動作時間が表示されます。
The operating time will be erased by pressing STRAIGHT キーを押すと動作時間が消去され
the “STRAIGHT” key. ます。

T1-1
0D 0H 0M
Minute (0M to 59M) / 分 （0M ∼ 59M）
Hour (0H to 23H) / 時間 （0H ∼ 23H）
Day (0D to 9999D) / 日数 （0D ∼ 9999D）

T1-2. POWER-RELAY ON T1-2. POWER-RELAY ON

RX-A3020/RX-V3073

The operation frequency of the power relay 電源リレー（RY182）の動作回数が 16 進数で

(RY182) is displayed in hexadecimal notation. 表示されます。
The operation frequency will be erased by STRAIGHT キーを押すと動作回数が消去され
pressing the “STRAIGHT” key. ます。

T1-2
PR-ON Num: 0
Operation frequency / 0 to FFFF (up to 65,535 times)
動作回数／ 0 ∼ FFFF（最大 65,535 回）

T1-3. POWER AMP B T1-3. POWER AMP B

The operation frequency of the POWER AMP POWER AMP B リレー（RY180）の動作回数が
B relay (RY180) is displayed in hexadecimal 16 進数で表示されます。
notation. STRAIGHT キーを押すと動作回数が消去され
The operation frequency will be erased by ます。
pressing the “STRAIGHT” key.

T1-3
P-AMP B Num: 0
Operation frequency / 0 to FF (up to 255 times)
動作回数／ 0 ∼ FF（最大 255 回）

T1-4. OUTPUT LEVEL T1-4. OUTPUT LEVEL

The maximum value of the speaker output level スピーカー出力レベルの最大値が 16 進数で表
is displayed in hexadecimal notation. 示されます。
The maximum value will be erased by pressing STRAIGHT キーを押すと最大値が消去されま
the “STRAIGHT” key. す。

T1-4
OUTLVL MAX: 0
Maximum value / 0 to FF
最大値／ 0 ∼ FF

66
 RX-A3020/RX-V3073

T1-5. POWER OFF TIME-OUT T1-5. POWER OFF TIME-OUT

The number of time-out times of each module 各モジュールで電源オフ時にタイムアウトし
when the power is turned off will be displayed た回数が 16 進数で表示されます。
in hexadecimal notation. STRAIGHT キーを押すとすべてのタイムアウ
All the number of time-out times will be erased トした回数が消去されます。
by pressing the “STRAIGHT” key.

T1-5
TO: 0/ 0/ 0/ 0 0 to FF (up to 255 times) / 0 ∼ FF（最大 255 回）
VIDEO
NET
HDMI
Power relay

RX-A3020/RX-V3073
T2. USAGE ENVIRONMENT T2. USAGE ENVIRONMENT
This menu is used to display the maximum level of 本機動作時のメイン ZONE ／ ZONE 2 ／ ZONE 3 ボ
the MAIN ZONE/ZONE 2/ZONE 3 volume and the リュームの最大レベル、ヒートシンク温度検出の最
maximum value of the detected heatsink temperature 大値が表示されます。
when this unit is operated.
※ ダイアグ中のメイン ZONE ／ ZONE 2 ／ ZONE 3
* The maximum level of the MAIN ZONE/ZONE 2/ ボリュームの最大レベル、ヒートシンク温度検出
ZONE 3 volume and the maximum value of the の最大値は保存されません。
detected heatsink temperature during the self-
diagnostic function mode will not be stored.

T2-1. MAIN ZONE HIGHEST VOLUME T2-1. MAIN ZONE HIGHEST VOLUME
The maximum value of the MAIN ZONE volume 1 分以上保持されたメイン ZONE ボリューム
level maintained for longer than 1 minute is レベルの最大値が表示されます。
displayed. STRAIGHT キ ー を 押 す と メ イ ン ZONE ボ
The maximum value of the MAIN ZONE volume リュームレベルの最大値が消去されます。
level will be erased by pressing the “STRAIGHT”
key.

T2-1
MAIN VOL:-----
Maximum value / -80.0 to +16.5 dB
最大値／ -80.0 ∼ +16.5 dB

67
 RX-A3020/RX-V3073

T2-2. ZONE 2 HIGHEST VOLUME T2-2. ZONE 2 HIGHEST VOLUME

The maximum value of the ZONE 2 volume 1 分以上保持された ZONE 2 ボリュームレベル
level maintained for longer than 1 minute is の最大値が表示されます。
displayed. STRAIGHT キーを押すと ZONE 2 ボリューム
The maximum value of the ZONE 2 volume レベルの最大値が消去されます。
level will be erased by pressing the
“STRAIGHT” key.

T2-2
Z2 VOL: -----
Maximum value / -80.0 to +16.5 dB
最大値／ -80.0 ∼ +16.5 dB

T2-3. ZONE 3 HIGHEST VOLUME T2-3. ZONE 3 HIGHEST VOLUME

The maximum value of the ZONE 3 volume 1 分以上保持された ZONE 3 ボリュームレベル
level maintained for longer than 1 minute is の最大値が表示されます。
RX-A3020/RX-V3073

displayed. STRAIGHT キーを押すと ZONE 3 ボリューム

The maximum value of the ZONE 3 volume レベルの最大値が消去されます。
level will be erased by pressing the “STRAIGHT”
key.

T2-3
Z3 VOL: -----
Maximum value / -80.0 to +16.5 dB
最大値／ -80.0 ∼ +16.5 dB

T2-4. THM1/THM2 HIGHEST TEMPERATURE T2-4. THM1/THM2 HIGHEST TEMPERATURE

The minimum value of the detected heatsink ヒートシンク温度検出の最小値が 16 進数で表
temperature is displayed in hexadecimal 示されます。
notation. STRAIGHT キーを押すとヒートシンク温度検
The minimum value of the detected heat sink 出の最小値が消去されます。
temperature will be erased by pressing the
正常値
“STRAIGHT” key.
THM1： 51 ∼ FF
Normal value THM2： 51 ∼ FF
THM1: 51 to FF
THM2: 51 to FF

T2-4
TMa MIN:--/-- Heatsink temperature / 0 (High) to FF (Low)
ヒートシンク温度／ 0（高い）∼ FF（低い）
THM2
THM1

68
 RX-A3020/RX-V3073

T2-5. THM3/THM4 HIGHEST TEMPERATURE T2-5. THM3/THM4 HIGHEST TEMPERATURE

Not for service. サービスでは使用しません。

T2-5
TMb MIN:--/--

T3. EXTERNAL EVENT T3. EXTERNAL EVENT

This menu is used to display the history of key キー操作の履歴が表示されます。
operation.
※ 同じキーを何回押しても、履歴は 1 回のみ保存さ
* No matter how many times the same key is pressed, れます。
it will be stored only once as its history. ※ ダイアグ中のキー操作は保存されません。
* The key operation during the self-diagnostic function
mode will not be stored. STRAIGHT キーを押すとすべてのキー操作履歴が消
去されます。
All history of key operation will be erased by pressing
the “STRAIGHT” key. ※ 図中の数値は参考例です。

RX-A3020/RX-V3073
* Numeric values in the figure are given as reference
only.

T3-1. HISTORY 1 T3-2. HISTORY 2 T3-3. HISTORY 3 T3-4. HISTORY 4

T3-1 T3-2 T3-3 T3-4
0205-81-FF-FF 0300-36-FF-FF 7A -007F 102

T3-5. HISTORY 5 T3-6. HISTORY 6 T3-7. HISTORY 7 T3-8. HISTORY 8

T3-5 T3-6 T3-7 T3-8
--- --- --- ---

69
 RX-A3020/RX-V3073

List of key operation / キー操作一覧

Display / 表示
Key number AD value 1 AD value 2 AD value 3 Key name / キー名称
キー番号 AD 値 1 AD 値 2 AD 値 3
0205 77 – 89 FF FF MAIN ZONE
0208 40 – 53 FF FF ZONE 2
020B 84 – 100 FF FF ZONE 3
020E xx – xx FF FF ZONE 4
020F 77 – 89 00 – 09 FF MAIN ZONE + STRAIGHT (Advanced setup mode)
0211 xx FF FF HD Radio CDM mode (U model)
0212 xx FF FF HD Rradio SPLIT mode (U model)
0300 2D – 3F FF FF SCENE 1
0301 1C – 2C FF FF SCENE 2
0302 0A – 1B FF FF SCENE 3
0303 00 – 09 FF FF SCENE 4
0500 FF 9C – AD FF PROGRAM
0501 FF 8A – 9B FF PROGRAM
0526 FF 0–9 FF STRAIGHT
0529 FF FF 9C – AD PURE DIRECT
0800 FF 0A – 1B FF TONE/BALANCE
0900 FF 2D – 3F FF CURSOR
0901 FF C0 – D1 FF CURSOR
RX-A3020/RX-V3073

0902 FF 54 – 64 FF CURSOR
0903 FF 77 – 89 FF CURSOR
0904 FF 65 – 76 FF ENTER
0905 FF D2 – E3 FF RETURN
0906 FF D2 – E3 FF ON SCREEN
0907 FF 40 – 53 FF OPTION
0908 FF AE – BF FF DISPLAY
0A00 FF FF 2D – 3F INFO
0C00 FF FF D2 – E3 ZONE CONTROL
2C00 FF FF 8A – 9B TUNING/CH
2C01 FF FF 77 – 89 TUNING/CH
2C02 FF FF 65 – 76 AM
2C03 FF FF 54 – 64 FM
2C04 FF FF 00 – 09 PRESET
2C05 FF FF 0A – 1B PRESET
2C06 FF FF 40 – 53 MEMORY
0101 VOLUME knob (–)
0102 VOLUME knob (+)
0103 INPUT knob (–)
0104 INPUT knob (+)
7A xxxx * For the details of the remote control key display, refer to
“REMOTE CONTROL”.
7E xxxx ※ リモコンキー表示の詳細は、“REMOTE CONTROL”を
参照してください。

70
 RX-A3020/RX-V3073

T4. INTERNAL INFORMATION T4. INTERNAL INFORMATION

T4-1. DSP INFORMATION T4-1. DSP INFORMATION

This menu is used to display the DSP information 再起動前にバックアップデータとしてメモ
stored in memory as backup data before リーに保存された DSP の情報が表示されます。
rebooting.
STRAIGHT キーを押すと DSP の情報は消去
The DSP information will be erased by pressing されます。
the ‘STRAIGHT “ key.

T4-1
DSP:--/--/-- --: Not stored / 保存なし

Decode format / デコードフォーマット

Channels / チャンネル数
Sampling frequency / サンプリング周波数

Sampling frequency Channels Decode format

サンプリング周波数 チャンネル数 デコードフォーマット

Display Sampling frequency [kHz] Display Channels Display Decode format

表示 サンプリング周波数［kHz］ 表示 チャンネル数 表示 デコードフォーマット

RX-A3020/RX-V3073
0 32 0 Dual Mono 0 Analog
1 44.1 1 1/0 1 PCM
2 48 2 2/0 2 Dolby Digital
3 64 3 3/0 3 Dolby Digital EX
4 88.2 4 2/1 4 DTS
5 96 5 3/1 5 DTS 9624
6 128 6 2/2 6 DTS ES Matrix
7 176.4 7 3/2 7 DTS ES Discrete
8 192 8 2/3 8 DTS 96 ES Matrix
10 8 9 3/3 9 AAC
11 11 10 2/4 10 DSD
12 12 11 3/4 11 Multi PCM
13 16 12 HD Multi channel 12 Dolby Digital Plus
14 22.05 13 “Unknown” 13 Dolby Digital Plus EX
15 24 14 Dolby True HD
16 “Unknown” 15 Dolby True HD EX
16 DTS Express
17 DTS HD
18 DTS HD Master Audio
19 Digital
20 MP3
21 WMA
22 FLAC
25 “Unknown”

71
 RX-A3020/RX-V3073

P1. SYSTEM MONITOR P1. SYSTEM MONITOR

This menu is used to display the A/D conversion パネルキー、プロテクションなどを検出しているマ
value of the microprocessor which detects panel keys イコンの A/D 変換値が、サブメニューで表示されま
and protection functions by using the sub-menu. す。
When “P1-8. KEY1/KEY2/KEY3” sub-menu is selected, サブメニュー P1-8. KEY1/KEY2/KEY3 にすると、
全キー
keys become inoperable due to detection of the の値を検出するためキー操作はできなくなりますが、
values of all keys. However, it is possible to advance リモコンの SCENE 4 （順送り）キーまたは SCENE
to the next menu by pressing the “SCENE 4” (forward) 3 （逆送り）キーを押すことにより、次のメニューに
key or “SCENE 3” (reverse) key on the remote control. 進めることができます。
* Numeric values in the figure are given as reference ※ 図中の数値は参考例です。
only.

P1-1. DC P1-1. DC
Power amplifier DC (DC voltage) output is パワーアンプ DC（直流電圧）出力の検出
detected. IC77 の 5 ピン
（DC_PRT）
の電圧が表示されます。
The voltage at 5 pin (DC_PRT) of IC77 is 正常値： 32 ∼ 74
displayed. （基準電圧：3.3 V=255）
Normal value: 32 to 74 ※ DC が正常値を外れるとプロテクションが
(Reference voltage: 3.3 V=255) 働き、電源が切れます。
RX-A3020/RX-V3073

* If DC becomes out of the normal value range,

the protection function works to turn off the
power.

P1-1
DC: 41

P1-2. PS1/PS2/PS3 P1-2. PS1/PS2/PS3

Power supply voltage (PS) protection detection. 電源電圧（PS）プロテクションの検出
The voltage at 2 pin (PS1_PRT)/1 pin (PS2_ IC77 の 2 ピ ン（PS1_PRT） ／ 1 ピ ン（PS2_
PRT)/13 pin (PS3_PRT) of IC77 are displayed. PRT）／ 13 ピン（PS3_PRT）の電圧が表示さ
れます。
Voltage detects
PS1: ACBL, AC12, AC7, +3.3HDR (U model), 検出電圧
-3.3V PS1： ACBL、AC12、AC7、-3.3V
PS2: ±12V, ±12RY, +5A, 44V PS2： ± 12V、± 12RY、+5A、44V
PS3: +5.5V PS3： +5.5V
Normal value 正常値
PS1: U model: 83 to 136 PS1： 47 ∼ 111
(PURE DIRECT mode: 127 to 180) （PURE DIRECT mode：100 ∼ 165）
C, R, T, K, A, B, G, F, L, S models: PS2： 43 ∼ 148
47 to 111 PS3： 132 ∼ 168
(PURE DIRECT mode: 100 to 165) （基準電圧：3.3 V=255）
PS2: 43 to 148
※ PS1、PS2 または PS3 が正常値を外れると
PS3: 132 to 168
プロテクションが働き、電源が切れます。
(Reference voltage: 3.3 V=255)
* If PS1, PS2 or PS3 becomes out of the normal
value range, the protection function works to
turn off the power.

P1-2
PS:111/ 98/151
PS3
PS2
PS1
72
 RX-A3020/RX-V3073

P1-3. THM1/THM2 P1-3. THM1/THM2

Temperature of the heatsink (THM) is detected. ヒートシンク温度（THM）の検出
The voltage at 12 pin (THM1) of IC77 and 1 IC77 の 12 ピン（THM1）
、IC76 の 1 ピン（THM2）
pin (THM2) of IC76 are displayed. の電圧が表示されます。
Normal value 正常値
THM1: 43 to 255 THM1： 43 ∼ 255
THM2: 43 to 255 THM2： 43 ∼ 255
(Reference voltage: 3.3 V=255) （基準電圧：3.3 V=255）
* If THM1/THM2 becomes out of the normal ※ THM1/THM2 が正常値を外れるとプロテク
value range, the protection function works ションが働き、電源が切れます。
to turn off the power.

P1-3
TMa:100 / 097
THM2
THM1

P1-4. THM3/THM4 P1-4. THM3/THM4

Not for service. サービスでは使用しません。

RX-A3020/RX-V3073
P1-4
TMb:--- / ---

P1-5. OUTPUT LEVEL P1-5. OUTPUT LEVEL

Speaker output level is detected. スピーカー出力レベルの検出
The voltage at 4 pin (AMP_OLV) of IC77 is IC77 の 4 ピン（AMP_OLV）の電圧が表示され
displayed. ます。
(Reference voltage: 3.3 V=255) （基準電圧：3.3 V=255）

P1-5
OUTLVL: 0

P1-6. LIMITER CONTROL P1-6. LIMITER CONTROL

Power limiter control is detected. 電源リミッター制御の検出
The voltage at 4 pin (AMP_LMT) of IC79 is IC79 の 4 ピン（AMP_LMT）の電圧が表示され
displayed. ます。
(Reference voltage: 3.3 V=255) （基準電圧：3.3 V=255）

P1-6
LMTCNT: 255

P1-7. L3 (J model) P1-7. L3 (J model)

Not for service. D 端子の L3（VIDEO P.C.B. CB301 の 11 ピン）
レベルの検出
IC77 の 14 ピン（L3_DET）の電圧が表示され
ます。
（基準電圧：3.3 V=255）

P1-7
L3: 130

73
 RX-A3020/RX-V3073

P1-8. KEY1/KEY2/KEY3 P1-7. KEY1/KEY2/KEY3

Panel key is detected. パネルキーの検出
When the A/D conversion value of the panel パネルキーの A/D 値が規定範囲から外れると、
key becomes out of the specified range, 正常な動きをしません。
normal operation will not be available. 下表をご覧になり、各キーの分圧抵抗の定数、
In that case, check the constant of voltage ハンダ不良等の確認をしてください。
dividing resistor, solder condition, etc. Refer to ※ P1-8. KEY1/KEY2/KEY3 メニューにすると、
table. 全キーの値を検出するためキー操作はでき
* When “P1-8. KEY1/KEY2/KEY3” menu is なくなりますが、リモコンの SCENE 4 （順
selected, keys become inoperable due to 送り）キーまたは SCENE 3 （逆送り）キー
detection of the values of all keys. However, を押すことにより、次のメニューに進める
it is possible to advance to the next menu ことができます。
by pressing the “SCENE 4” (forward) key （基準電圧：3.3 V=255）
or “SCENE 3” (reverse) key on the remote
control.
(Reference voltage: 3.3 V=255)

P1-8
KY:248/255/255
RX-A3020/RX-V3073

KEY3
KEY2
KEY1

Display / 表示 KEY1 Display / 表示 KEY2 Display / 表示 KEY3

0−9 SCENE 4 0−9 STRAIGHT 0−9 PRESET
10 − 27 SCENE 3 10 − 27 TONE/BALANCE 10 − 27 PRESET
28 − 44 SCENE 2 28 − 44 OPTION 28 − 44 MEMORY
45 − 63 SCENE 1 45 − 63 45 − 63 INFO
64 − 83 ZONE 2 ON/OFF 64 − 83 ON SCREEN 64 − 83 ZONE CONTROL
84 − 100 ZONE 3 ON/OFF 84 − 100 84 − 100 FM
101 − 118 ZONE 4 ON/OFF 101 − 118 ENTER 101 − 118 AM
119 − 137 MAIN ZONE 119 − 137 119 − 137 TUNING/CH
255 Key off 138 − 155 PROGRAM 138 − 155 TUNING/CH
156 − 173 PROGRAM 156 − 173 PURE DIRECT
174 − 191 DISPLAY 255 Key off
192 − 209
210 − 227 RETURN
255 Key off

P1-9. USB-VBUS P1-9. USB-VBUS

Not for service. サービスでは使用しません。

P1-9
USB-VBUS: 0

74
 RX-A3020/RX-V3073

P2. PROTECTION HISTORY P2. PROTECTION HISTORY

This menu is used to display the history of protection プロテクション履歴が表示されます。
function.
プロテクション履歴 1 ∼ 4 には、そのそれぞれにプ
In the protection function history 1 to 4, the setting ロテクション動作時の設定情報が保存されます。サ
information for operation of each protection function ブメニュー選択後、 （カーソル下）キー / （カー
will be stored. After selecting the sub-menu, press ソル上）キーを押すと設定情報が表示されます。
the “ ”(cursor down) key / “ ”(cursor up) key, and
STRAIGHT キーを押すと、すべてのプロテクション
the setting information will be displayed.
履歴と、設定情報が消去されます。
All history of protection function and setting information
will be erased by pressing the “STRAIGHT” key. ※ 図中の数値は参考例です。

* Numeric values in the figure are given as reference

only.

The display will be changed by pressing the “ ”(cursor down)

P2-1 2-1. History 1 / 履歴 1
key / “ ”(cursor up) key.
4th:I Prt
（カーソル下）キー / （カーソル上）キーを押すと表示が
切り替わります。
Setting information for operation of the protection function
P2-2 P2-2. History 2 / 履歴 2 プロテクション動作時の設定情報
3rd:PS1 000

RX-A3020/RX-V3073
P2-x POWER PORT
P-PORT:0011000 The status of the port for the power control is
displayed.
P2-3 P2-3. History 3 / 履歴 3 電源コントロール用ポートの状態が表示されます。

2nd:Dc 000 0: Off / オフ

1: On / オン
FL: FLD_PON (DIGITAL P.C.B. IC79, 32pin)
USB: USB_VBUS_PON
P2-4 P2-4. History 4 / 履歴 4
(DIGITAL P.C.B. IC79, 84pin)
1st:Tmp 000
NET: NCPU_PON (DIGITAL P.C.B. IC79, 82 pin)
xxx: A/D conversion value of
VIDEO: VID_PON (DIGITAL P.C.B. IC73, 15pin)
voltage at the moment
when the protection DSP: DSP_PON (DIGITAL P.C.B. IC79, 47pin)
function worked. HDMI: HDMI_PON (DIGITAL P.C.B. IC72, 2pin)
(Reference voltage: 3.3 V Power Relay: +3.3s_PON
=255) (DIGITAL P.C.B. IC79, 165pin)

プロテクションが働いた P2-x POWER-RELAY ON TIME

瞬間の電圧の A/D 変換値 PR-ON TM:1000M The operation time of the power relay (RY182 of
（基準値：3.3 V=255） AMPPOWER P.C.B.) is displayed by the unit time of
minute.
0 to 1,092 minute (maximum)
電源リレー（AMPPOWER P.C.B. の RY182）の動
作時間が分単位で表示されます。
0 ∼ 1,092 分（最大）

P2-x LAST INPUT

LAST IN:AUDIO3 The input source which was selected last is

displayed.
最後に選択された入力ソースが表示されます。

P2-x LAST VOLUME LEVEL

LAST VOL:-16.5 The volume level which was selected last is

displayed.
-80.0 to +16.5 dB
最後に選択されたボリュームレベルが表示されま
す。
-80.0 ∼ +16.5 dB

75
 RX-A3020/RX-V3073

S1. FIRMWARE UPDATE S1. FIRMWARE UPDATE

Not for service. サービスでは使用しません。

S1-1
F/W UPDATE?

S2. SET INFORMATION S2. SET INFORMATION

This menu is used to display the model name and 本機のモデル名、仕向け先が表示されます。
destination of this unit.

S2-1. MODEL S2-1. MODEL

The model name of this unit is displayed. 本機のモデル名が表示されます。

S2-1
MDL:A3020- 255
RX-A3020/RX-V3073

Not for service.

Model name
A3020 : RX-A3020
V3073 : RX-V3073

S2-2. DESTINATION S2-2. DESTINATION

The destination of this unit is displayed. 本機の仕向け先が表示されます。

S2-2
DEST:U 27

A/D conversion value

Destination

Destination J U C R (R, S) T K A BG (B, G, F) L

A/D conversion value
0 − 12 13 − 39 40 − 67 68 − 92 93 − 115 116 − 140 141 − 169 199 − 221 222 − 244
(3.3 V=255)

S2-3. DBG S2-3. DBG

Not for service. サービスでは使用しません。

S2-3
DBG:255

S2-4. NET RESTART COUNTER S2-4. NET RESTART COUNTER

Not for service. サービスでは使用しません。

S2-4
NRC: 0
NRC (Net Restart Counter)

76
 RX-A3020/RX-V3073

S3. FACTORY PRESET S3. FACTORY PRESET

This menu is used to reserve/inhibit initialization of the バックアップ IC（EEPROM：DIGITAL P.C.B. の IC78）
back-up IC (EEPROM: IC78 on DIGITAL P.C.B.). の初期化を予約／禁止します。

S3-1 S3-1. PRESET INHIBIT (Initialization inhibited) / PRESET INHIBIT（初期化禁止）

PRESET INHI Initialization of the back-up IC is not executed. Select this sub-menu to protect the values set by the user.
バックアップ用 IC の初期化は行われません。ユーザーの設定値を保護するときは、こちらを選択してく
ださい。

S3-2 S3-2. PRESET RESERVED (Initialization reserved) / PRESET RESERVED（初期化予約）

PRESET RSRV Initialization of the back-up IC is reserved. (Actual initialization is executed when the power is turned on
next.) To reset to the original factory settings or to reset the backup IC, select this sub-menu and press
the “ ” (Power) key to turn off the power.
ユーザーメモリーの初期化が予約されます。（実際に初期化されるのは、次回の電源投入時です。）工場
出荷時やユーザーメモリーをリセットしたいときは、こちらを選択してから“ ”（電源）キーを押して
電源を切ってください。

CAUTION: Before setting to the PRESET RESERVED, 注意： PRESET RESERVED を 選 ん で 初 期 化 を す る 前 に、

write down the existing preset memory content チューナーのユーザーメモリーの内容を書き写し

RX-A3020/RX-V3073
of the tuner. (This is because setting to the てください。（初期化をすると、チューナーのユー
PRESET RESERVED will cause the user ザーメモリーの内容は消えてしまいます。）
memory content to be erased.)

77
 RX-A3020/RX-V3073

S4. ROM VERSION/CHECKSUM S4. ROM VERSION/CHECKSUM

The firmware version and checksum values are ファームウェアのバージョン、チェックサムが表示
displayed. されます。
The checksum is obtained by adding the data at every チェックサムは、データを 8 ビットごとに加算して
8-bit and expressing the result as a hexadecimal いき、16 進数で表記したものです。
notation. ※ 図中の数値は参考例です。
* Numeric values in the figure are given as reference
only.

S4-1 S4-1. SYSTEM VERSION

SYS-VER. 1.10 The firmware version is displayed.
ファームウェアのバージョンが表示されます。

S4-2 S4-2. MICROPROCESSOR VERSION

VER.00043 The firmware version of MICROPROCESSOR (IC79 on DIGITAL P.C.B.) is displayed.
マイコン（DIGITAL P.C.B. の IC79）のファームウェアのバージョンが表示されます。

S4-3 S4-3. MICROPROCESSOR CHECKSUM

RX-A3020/RX-V3073

SUM.DD81 The checksum value of MICROPROCESSOR (IC79 on DIGITAL P.C.B.) is displayed.

マイコン（DIGITAL P.C.B. の IC79）のチェックサムが表示されます。

S4-4 S4-4. FLASH ROM VERSION

FR-V.00033 The firmware version of FLASH ROM (IC75 on DIGITAL P.C.B.) is displayed.
FLASH ROM（DIGITAL P.C.B. の IC75）のファームウェアのバージョンが表示されます。

S4-5 S4-5. FLASH ROM CHECKSUM

FR-S.0E43 The checksum value of FLASH ROM (IC75 on DIGITAL P.C.B.) is displayed.
FLASH ROM（DIGITAL P.C.B. の IC75）のチェックサムが表示されます。

S4-6 S4-6. NETWORK MICROPROCESSOR VERSION

S-VER.0068 The firmware version of Network microprocessor (IC951 on DIGITAL P.C.B.) is displayed.
ネットワークマイコン（DIGITAL P.C.B. の IC951）のファームウェアのバージョンが表示されます。

S4-7 S4-7. NETWORK MICROPROCESSOR CHECKSUM

S-SUM.8903367A The checksum value of Network microprocessor (IC951 on DIGITAL P.C.B.) is displayed.
ネットワークマイコン（DIGITAL P.C.B. の IC951）のチェックサムが表示されます。

S4-8 S4-8. DSP1 VERSION

D1-V. 1.07r3 The firmware version of DSP1 (IC911 on DIGITAL P.C.B.) is displayed.
DSP1（DIGITAL P.C.B. の IC911）のファームウェアのバージョンが表示されます。

S4-9 S4-9. DSP1 CHECKSUM

D1-S.164AE2DC The checksum value of DSP1 (IC911 on DIGITAL P.C.B.) is displayed.
DSP1（DIGITAL P.C.B. の IC911）のチェックサムが表示されます。

S4-10 S4-8. DSP2 VERSION

D2-V. 1.07r3 The firmware version of DSP2 (IC920 on DIGITAL P.C.B.) is displayed.
DSP2（DIGITAL P.C.B. の IC920）のファームウェアのバージョンが表示されます。

78
 RX-A3020/RX-V3073

S4-11 S4-9. DSP2 CHECKSUM

D2-S.6A0DC68B The checksum value of DSP2 (IC920 on DIGITAL P.C.B.) is displayed.
DSP2（DIGITAL P.C.B. の IC920）のチェックサムが表示されます。

S4-12 S4-12. GUI VERSION

G-V.000007048 The firmware version of GUI data is displayed.
GUI データのファームウェアのバージョンが表示されます。

S4-13 S4-13. FPGA GUI VERSION

FPGA-G-V. 18 The firmware version of GUI section in FPGA (IC50 on DIGITAL P.C.B.) is displayed.
FPGA（DIGITAL P.C.B. の IC50）の GUI 部のファームウェアのバージョンが表示されます。

S4-14 S4-14. FPGA SD (Standard Definition) VERSION

FPGA-S-V. 12 The firmware version of SD I/P scaler section in FPGA (IC50 on DIGITAL P.C.B.) is displayed.
FPGA（DIGITAL P.C.B. の IC50）の SD I/P スケーラー部のファームウェアのバージョンが表示されます。

S4-15 S4-15. FPGA HD (High Definition) VERSION

RX-A3020/RX-V3073
FPGA-H-V. 6 The firmware version of HD I/P scaler section in FPGA (IC50 on DIGITAL P.C.B.) is displayed.
FPGA（DIGITAL P.C.B. の IC50）の HD I/P スケーラー部のファームウェアのバージョンが表示されます。

S4-16 S4-16. HQV VERSION

HQV-VER. 4.4 The firmware version of HQV (IC64 DIGITAL P.C.B.) is displayed.
HQV（IC64 DIGITAL P.C.B.）のファームウェアのバージョンが表示されます。

S4-17 S4-17. HD RADIO VERSION (U model)

HDR. A001 The firmware version of HD radio is displayed.

79
 RX-A3020/RX-V3073

■ POWER AMPLIFIER ADJUSTMENT / パワーアンプ調整

Perform all adjustments with no signal applied. 無信号状態ですべての調整を行います。
Warming up before adjustment is not required. 調整前のウォ−ミングアップは必要ありません。

● Idling Current Adjustment ● アイドリング電流調整

1. Turn all the semi-fixed variable resisters for idling 1. すべてのチャンネルのアイドリング調整用半固定
current adjustment counterclockwise fully. ボリュームを左いっぱいに回します。
2. Turn on the power to this unit. 2. 本機に電源を投入します。
3. Adjust all channels so that the voltage value 3. テストポイント電圧が表の規格の中心値になるよ
at test point is the same as center value of the うにすべてのチャンネルを再調整します。
specified range.

● DC Offset Confirmation ● DC オフセット確認

After idling current adjustment, confirm that DC offset アイドリング調整後、すべてのチャンネルの DC オフ
of all channels are within the specified range. セットが規格以内であることを確認します。

AMP (1) P.C.B.

Idling current adjustments DC offset confirmations
RX-A3020/RX-V3073

Item アイドリング電流調節 DC オフセット確認

チャンネル Test Point Adjustment Point Rating Test Point Rating
テストポイント 調整箇所 規格 テストポイント 規格
Center CB105 pin1, pin2 VR107 Speaker Terminal (TE150)
Surround L CB107 pin1, pin2 VR106 Speaker Terminal (TE153) DC -100 mV
Front L CB108 pin1, pin2 VR104 DC 15 ±2 mV Speaker Terminal (TE150) to
Surround Back L CB109 pin1, pin2 VR105 Speaker Terminal (TE152) +100 mV
Front Presence L CB106 pin1, pin2 VR108 Speaker Terminal (TE180)

AMP (1)

CB108
CB105 VR108 VR106 CB107 VR105 CB109
VR104
VR107 CB106

+ – + – + – + – + –
DC 15 ±2 mV DC 15 ±2 mV DC 15 ±2 mV DC 15 ±2 mV DC 15 ±2 mV
Center Surround L Front L Idling current
Front Presence L Surround Back L

80
 RX-A3020/RX-V3073

AMP (2) P.C.B.

Idling current adjustments DC offset confirmations
Item アイドリング電流調節 DC オフセット確認
チャンネル Test Point Adjustment Point Rating Test Point Rating
テストポイント 調整箇所 規格 テストポイント 規格
Surround Back R CB104 pin1, pin2 VR100 Speaker Terminal (TE152)
Front R CB103 pin1, pin2 VR102 Speaker Terminal (TE150) DC -100 mV to
DC 15 ±2 mV
Surround R CB102 pin1, pin2 VR101 Speaker Terminal (TE153) +100 mV
Front Presence R CB101 pin1, pin2 VR103 Speaker Terminal (TE180)

AMP (2)

CB104 VR102 CB103 VR101 CB102 VR103

VR100 CB101

RX-A3020/RX-V3073
+ – + – + – + –
DC 15 ±2 mV DC 15 ±2 mV DC 15 ±2 mV DC 15 ±2 mV
Front R Surround R Idling current
Surround Back R Front Presence R

81
 RX-A3020/RX-V3073

■ DISPLAY DATA
● V4001 : 23-MT-04GINK (OPERATION P.C.B.)

82 1

PATTERN AREA

● PIN CONNECTION

Pin No. 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
Connection F2 F2 NP NP NP NP LGND PGND VH VDD OSC RESET CS CP DA TSA TSB NP NP NP NP NP

Pin No. 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31
Connection NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP

Pin No. 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
RX-A3020/RX-V3073

Connection NP NP NP NP NP NP NP NP NP NP NP NP NP NC NC NC NC NC NC NC NC NC Q23G 23G NP NP NP NP F1 F1

Note : 1) F1, F2 ..... Filament pin 2) NP ..... No pin 3) DL ..... Datum line pin 4) LGND ..... Logic GND pin 5) PGND ..... Power GND pin
6) HV ..... High voltage supply pin 7) VDD ..... Logic voltage supply pin 8) OSC ..... Pin for self-oscillation 9) RESET ..... Reset input
10) CS ..... Chip select input pin 11) CP ..... Shift resister clock 12) DA ..... Serial data input 13) TSA,B ..... Test pin
14) Solder composition is Sn-3Ag-0.5Cu. 15) Field of vision is a minimum of 25.0° from the upper side. 22.8° from the lower side.
16) 23G ..... Grid 17) Q23G ..... Driver output port 18) NC ..... No connection

● GRID ASSIGNMENT
16G 18G 20G 22G
1G 2G 3G 4G 5G 6G 7G 8G 9G 10G 11G 12G 13G 14G 23G
15G 17G 19G 21G

(B) (A) (B) (A) (B) (A) (B) (A) (B)

(B) (B) (B) (B) (B) (B) (B) (B) (B) (B) (B) (B) (B) (B)
(A) (A) (A) (A) (A) (A) (A) (A) (A) (A) (A) (A) (A) (A)

23G 1a 2a 3a

a
1-1 2-1 3-1 4-1 5-1 f b
S5

S2 1-2 2-2 3-2 4-2 5-2

g
e c
1-3 2-3 3-3 4-3 5-3 d

1-4 2-4 3-4 4-4 5-4

(23G)
1-5 2-5 3-5 4-5 5-5
S1 S6
S3 1-6 2-6 3-6 4-6 5-6

(23G) 1-7 2-7 3-7 4-7 5-7

S4
(1G-22G) (23G)

82
 RX-A3020/RX-V3073

• Anode connection

16G, 20G, 15G, 17G, 21G,

1G-14G 15G 18, 19G 22G 23G 1G-14G 19, 20G 23G
17G 21G 16G 18G 21G

D0B 1-1B 1-1B 1-1B 1-1B 1-1B 1-1B 1a D0A 1-1A 1-1A 1-1A 1-1A 1-1A

D1B 2-1B 2-1B 2-1B 2-1B 2-1B 2-1B 2a D1A 2-1A 2-1A 2-1A 2-1A 2-1A

D2B 3-1B 3-1B 3-1B 3-1B 3-1B 3-1B 3a,3f,3c,3d D2A 3-1A 3-1A 3-1A 3-1A 3-1A

D3B 4-1B 4-1B 4-1B 4-1B 4-1B 4-1B 1b D3A 4-1A 4-1A 4-1A 4-1A 4-1A

D4B 5-1B 5-1B 5-1B 5-1B 5-1B 5-1B 2b D4A 5-1A 5-1A 5-1A 5-1A 5-1A

D5B 1-2B 1-2B 1-2B 1-2B 1-2B 1-2B 3g D5A 1-2A 1-2A 1-2A 1-2A 1-2A

D6B 2-2B 2-2B 2-2B 2-2B 2-2B 2-2B 1f D6A 2-2A 2-2A 2-2A 2-2A 2-2A

D7B 3-2B 3-2B 3-2B 3-2B 3-2B 3-2B 2f D7A 3-2A 3-2A 3-2A 3-2A 3-2A

D8B 4-2B 4-2B 4-2B 4-2B 4-2B 4-2B 3b,3e D8A 4-2A 4-2A 4-2A 4-2A 4-2A

D9B 5-2B 5-2B 5-2B 5-2B 5-2B 5-2B 1g D9A 5-2A 5-2A 5-2A 5-2A 5-2A

D10B 1-3B 1-3B 1-3B 1-3B 1-3B 1-3B 2g D10A 1-3A 1-3A 1-3A 1-3A 1-3A

D11B 2-3B 2-3B 2-3B 2-3B 2-3B 2-3B S5 D11A 2-3A 2-3A 2-3A 2-3A 2-3A

RX-A3020/RX-V3073
D12B 3-3B 3-3B 3-3B 3-3B 3-3B 3-3B 1c D12A 3-3A 3-3A 3-3A 3-3A 3-3A

D13B 4-3B 4-3B 4-3B 4-3B 4-3B 4-3B 2c D13A 4-3A 4-3A 4-3A 4-3A 4-3A

D14B 5-3B 5-3B 5-3B 5-3B 5-3B 5-3B 1e D14A 5-3A 5-3A 5-3A 5-3A 5-3A

D15B 1-4B 1-4B 1-4B 1-4B 1-4B 1-4B 2e D15A 1-4A 1-4A 1-4A 1-4A 1-4A S1

D16B 2-4B 2-4B 2-4B 2-4B 2-4B 2-4B 1d D16A 2-4A 2-4A 2-4A 2-4A 2-4A S1

D17B 3-4B 3-4B 3-4B 3-4B 3-4B 3-4B 2d D17A 3-4A 3-4A 3-4A 3-4A 3-4A S3

D18B 4-4B 4-4B 4-4B 4-4B 4-4B 4-4B S6 D18A 4-4A 4-4A 4-4A 4-4A 4-4A

D19B 5-4B 5-4B 5-4B 5-4B 5-4B 5-4B D19A 5-4A 5-4A 5-4A 5-4A 5-4A

D20B 1-5B 1-5B 1-5B 1-5B 1-5B 1-5B D20A 1-5A 1-5A 1-5A 1-5A 1-5A

D21B 2-5B 2-5B 2-5B 2-5B 2-5B 2-5B (UP) D21A 2-5A 2-5A 2-5A 2-5A 2-5A S4

D22B 3-5B 3-5B 3-5B 3-5B 3-5B 3-5B D22A 3-5A 3-5A 3-5A 3-5A 3-5A –

D23B 4-5B 4-5B 4-5B 4-5B 4-5B 4-5B D23A 4-5A 4-5A 4-5A 4-5A 4-5A –

D24B 5-5B 5-5B 5-5B 5-5B 5-5B 5-5B D24A 5-5A 5-5A 5-5A 5-5A 5-5A –

D25B 1-6B 1-6B 1-6B 1-6B 1-6B 1-6B (UP) D25A 1-6A 1-6A 1-6A 1-6A 1-6A –

D26B 2-6B 2-6B 2-6B 2-6B 2-6B 2-6B D26A 2-6A 2-6A 2-6A 2-6A 2-6A –

D27B 3-6B 3-6B 3-6B 3-6B 3-6B 3-6B D27A 3-6A 3-6A 3-6A 3-6A 3-6A –

D28B 4-6B 4-6B 4-6B 4-6B 4-6B 4-6B D28A 4-6A 4-6A 4-6A 4-6A 4-6A –

D29B 5-6B 5-6B 5-6B 5-6B 5-6B 5-6B D29A 5-6A 5-6A 5-6A 5-6A 5-6A –

D30B 1-7B 1-7B 1-7B 1-7B 1-7B 1-7B (DOWN) D30A 1-7A 1-7A 1-7A 1-7A 1-7A –

D31B 2-7B 2-7B 2-7B 2-7B 2-7B 2-7B D31A 2-7A 2-7A 2-7A 2-7A 2-7A –

D32B 3-7B 3-7B 3-7B 3-7B 3-7B 3-7B D32A 3-7A 3-7A 3-7A 3-7A 3-7A –

D33B 4-7B 4-7B 4-7B 4-7B 4-7B 4-7B D33A 4-7A 4-7A 4-7A 4-7A 4-7A –

D34B 5-7B 5-7B 5-7B 5-7B 5-7B 5-7B (DOWN) D34A 5-7A 5-7A 5-7A 5-7A 5-7A –

83
 RX-A3020/RX-V3073

• Timing chart

16G, 20G, 15G, 17G, 21G,

1G-14G 15G 18, 19G 22G 23G 1G-14G 19, 20G 23G
17G 21G 16G 18G 21G

D0B T1-T14 T15 T17 T19 T21 T23 T24 D0A T1-T14 T15 T17 T19 T21 T23

D1B T1-T14 T15 T17 T19 T21 T23 T24 D1A T1-T14 T15 T17 T19 T21 T23

D2B T1-T14 T15 T17 T19 T21 T23 T24 D2A T1-T14 T15 T17 T19 T21 T23

D3B T1-T14 T15 T17 T19 T21 T23 T24 D3A T1-T14 T15 T17 T19 T21 T23

D4B T1-T14 T15 T17 T19 T21 T23 T24 D4A T1-T14 T15 T17 T19 T21 T23

D5B T1-T14 T15 T17 T19 T21 T23 T24 D5A T1-T14 T15 T17 T19 T21 T23

D6B T1-T14 T15 T17 T19 T21 T23 T24 D6A T1-T14 T15 T17 T19 T21 T23

D7B T1-T14 T15 T17 T19 T21 T23 T24 D7A T1-T14 T15 T17 T19 T21 T23

D8B T1-T14 T15 T17 T19 T21 T23 T24 D8A T1-T14 T15 T17 T19 T21 T23

D9B T1-T14 T15 T17 T19 T21 T23 T24 D9A T1-T14 T15 T17 T19 T21 T23

D10B T1-T14 T15 T17 T19 T21 T23 T24 D10A T1-T14 T15 T17 T19 T21 T23

D11B T1-T14 T15 T17 T19 T21 T23 T24 D11A T1-T14 T15 T17 T19 T21 T23

D12B T1-T14 T15 T17 T19 T21 T23 T24 D12A T1-T14 T15 T17 T19 T21 T23

D13B T1-T14 T15 T17 T19 T21 T23 T24 D13A T1-T14 T15 T17 T19 T21 T23
RX-A3020/RX-V3073

D14B T1-T14 T15 T17 T19 T21 T23 T24 D14A T1-T14 T15 T17 T19 T21 T23

D15B T1-T14 T15 T17 T19 T21 T23 T24 D15A T1-T14 T15 T17 T19 T21 T23

D16B T1-T14 T15 T17 T19 T21 T23 T24 D16A T1-T14 T15 T17 T19 T21 T23

D17B T1-T14 T15 T17 T19 T21 T23 T24 D17A T1-T14 T15 T17 T19 T21 T23

D18B T1-T14 T15 T17 T19 T21 T23 T24 D18A T1-T14 T15 T17 T19 T21 T23

D19B T1-T14 T15 T17 T19 T21 T23 T24 D19A T1-T14 T15 T17 T19 T21 T23

D20B T1-T14 T15 T17 T19 T21 T23 T24 D20A T1-T14 T15 T17 T19 T21 T23

D21B T1-T14 T15 T17 T19 T21 T23 T24 D21A T1-T14 T15 T17 T19 T21 T23

D22B T1-T14 T15 T17 T19 T21 T23 T24 D22A T1-T14 T15 T17 T19 T21 –

D23B T1-T14 T15 T17 T19 T21 T23 T24 D23A T1-T14 T15 T17 T19 T21 –

D24B T1-T14 T15 T17 T19 T21 T23 T24 D24A T1-T14 T15 T17 T19 T21 –

D25B T1-T14 T15 T17 T19 T21 T23 T24 D25A T1-T14 T15 T17 T19 T21 –

D26B T1-T14 T15 T17 T19 T21 T23 T24 D26A T1-T14 T15 T17 T19 T21 –

D27B T1-T14 T15 T17 T19 T21 T23 T24 D27A T1-T14 T15 T17 T19 T21 –

D28B T1-T14 T15 T17 T19 T21 T23 T24 D28A T1-T14 T15 T17 T19 T21 –

D29B T1-T14 T15 T17 T19 T21 T23 T24 D29A T1-T14 T15 T17 T19 T21 –

D30B T1-T14 T15 T17 T19 T21 T23 T24 D30A T1-T14 T15 T17 T19 T21 –

D31B T1-T14 T15 T17 T19 T21 T23 T24 D31A T1-T14 T15 T17 T19 T21 –

D32B T1-T14 T15 T17 T19 T21 T23 T24 D32A T1-T14 T15 T17 T19 T21 –

D33B T1-T14 T15 T17 T19 T21 T23 T24 D33A T1-T14 T15 T17 T19 T21 –

D34B T1-T14 T15 T17 T19 T21 T23 T24 D34A T1-T14 T15 T17 T19 T21 –

84
 RX-A3020/RX-V3073

■ IC DATA
IC911, IC920: D80YK113CPTP400 (DIGITAL P.C.B.)
DSP (Digital signal processor)
* No replacement part available. / サービス部品供給なし

JTAG Interface DSP Subsystem

System Control
C674xTM
DSP MICRO-
PLL/Clock PROCESSOR
Input Generator
Clock(s) w/OSC Memory Protection
I/O Protection AET
General-
Purpose 32 KB 32 KB
Timer L1 Pgm L1 RAM
Power/Sleep
General- Controller
Purpose 256 KB L2 RAM
Timer RTC/ Pin
(Watchdog) 32-KHz Multiplexing 1024 KB L2 ROM
OSC

Switched Control Resource (SCR)

Peripherals
DMA Audio Ports Serial Interface

GPIO
EDMA3 dMAX McASP I2C SPI UART
w/FIFO

RX-A3020/RX-V3073
Control Timers Shared Memory

128 KB
eHRPWM eCAP eQEP RAM

Connectivity External Memory Interface

USB2.0 MMC/SD EMIFA(8b/16b) EMIFB

OTG Ctlr HPI (8b) NAND/Flash SDRAM Only
PHY 16b SDRAM (16b/32b)
125 AHCLKX0/AHCLKX2/USB_REFCLKIN/GP2[11]
130 ACLKR0/ECAP1/APWM1/GP2[15]

126 ACLKX0/ECAP0/APWM0/GP2[12]

123 UART1_TXD/AXR0[10]/GP3[10]
132 AMUTE1/EHRPWMTZ/GP4[14]

129 AHCLKR0/GP2[14]/BOOT[11]

122 UART1_RXD/AXR0[9]/GP3[9]
124 AXR0[11]/AXR2[0]/GP3[11]
127 AFSX0/GP2[13]/BOOT[10]

118 AXR0[6]/ACLKR2/GP3[6]

112 AXR0[1]/ACLKX2/GP3[1]
116 AXR0[4]/AXR2[1]/GP3[4]
115 AXR0[3]/AXR2[2]/GP3[3]

113 AXR0[2]/AXR2[3]/GP3[2]

111 AXR0[0]/AFSR2/GP3[0]
117 AXR0[5]/AFSX2/GP3[5]

105 EMB_A[10]/GP7[12]

EMB_A[11]/GP7[13]

EMB_A[12]/GP3[13]
107 EMB_BA[0]/GP7[1]
106 EMB_BA[1]/GP7[0]

EMB_A[8]/GP7[10]

EMB_A[9]/GP7[11]
103 EMB_A[0]/GP7[2]
102 EMB_A[1]/GP7[3]
101 EMB_A[2]/GP7[4]
100 EMB_A[3]/GP7[5]

EMB_A[4]/GP7[6]
EMB_A[5]/GP7[7]
EMB_A[6]/GP7[8]
EMB_A[7]/GP7[9]
121 AXR0[8]/GP3[8]
120 AXR0[7]/GP3[7]
131 AFSR0/GP3[12]

108 EMB_CS[0]
110 EMB_RAS
128 DVDD

119 DVDD

114 CVDD

109 DVDD

104 CVDD

DVDD

CVDD

DVDD
99
98
97
96
95
94
93
92
91
90
89

RSV2 133 88 EMB_SDCKE

USB0_VDDA12 134 87 DVDD
USB0_VDDA18 135 86 EMB_CLK
NC 136 85 EMB_WE/DQM[1]/GP5[14]
USB0_DP 137 84 EMB_D[8]/GP6[8]
USB0_DM 138 83 EMB_D[9]/GP6[9]
NC 139 82 EMB_D[10]/GP6[10]
USB0_VDDA33 140 81 DVDD
PLL0_VDDA 141 80 EMB_D[11]/GP6[11]
PLL0_VSSA 142 79 EMB_D[12]/GP6[12]
OSCIN 143 78 EMB_D[13]/GP6[13]
OSCVSS 144 77 CVDD
OSCOUT 145 76 EMB_D[14]/GP6[14]
RESET 146 75 DVDD
CVDD 147 74 EMB_D[15]/GP6[15]
RTC_XI 148 73 EMB_D[0]/GP6[0]
RTC_CVDD 149 72 EMB_D[1]/GP6[1]
TRST 150 71 DVDD
DVDD 151 70 EMB_D[2]/GP6[2]
TMS 152 69 CVDD
TDI 153 68 EMB_D[3]/GP6[3]
CVDD 154 67 CVDD
TCK 155 66 EMB_D[4]/GP6[4]
TDO 156 65 DVDD
GP7[14] 157 64 EMB_D[5]/GP6[5]
DVDD 158 63 EMB_D[6]/GP6[6]
CVDD 159 62 EMB_D[7]/GP6[7]
AHCLKX1/EPWMQB/GP3[14] 160 61 CVDD
CVDD 161 60 EMB_WE_DQM[0]/GP5[15]
ACLKX1/EPWMQA/GP3[15] 162 59 EMB_WE
AFSX1/EPWMSYNCI/EPWMSYNC0/GP4[10] 163 58 DVDD
DVDD 164 57 EMB_CAS
ACLKR1/ECAP2/APWM2/GP4[12] 165 56 CVDD
AFSR1/GP4[13] 166 55 EMA_WE]/UHPI_HRW/AXR0[12]/GP2[3]/BOOT[14]
CVDD 167 54 EMA_D[7]/MMCSD_DAT[7]/UHPI_HD[7]/GP0[7]/BOOT[13]
AXR1[8]/EPWM1A/GP4[8] 168 53 DVDD
AXR1[7]/EPWM1B/GP4[7] 169 52 EMA_D[6]/MMCSD_DAT[6]/UHPI_HD[6]/GP0[6]
AXR1[6]/EPWM2A/GP4[6] 170 51 EMA_D[5]/MMCSD_DAT[5]/UHPI_HD[5]/GP0[5]
AXR1[5]/EPWM2B/GP4[5] 171 50 CVDD
DVDD 172 49 EMA_D[4]/MMCSD_DAT[4]/UHPI_HD[4]/GP0[4]
AXR1[4]/EQEP1B/GP4[4] 173 48 EMA_D[3]/MMCSD_DAT[3]/UHPI_HD[3]/GP0[3]
AXR1[3]/EQEP1A/GP4[3] 174 47 DVDD
AXR1[2]/GP4[2] 175 46 EMA_D[2]/MMCSD_DAT[2]/UHPI_HD[2]/GP0[2]
AXR1[1]/GP4[1] 176 45 EMA_D[1]/MMCSD_DAT[1]/UHPI_HD[1]/GP0[1]
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

DVDD 33
EMA_A[4]/GP1[4] 34
35
36

EMA_A[7]/GP1[7] 37
CVDD 38
EMA_A[8]/GP1[8] 39
EMA_A[9]/GP1[9] 40
41
42
43

EMA_D[0]/MMCSD_DAT[0]/UHPI_HD[0]/GP0[0]/BOOT[12] 44
1
2
3
4
5
6
7
8
9
DVDD

CVDD

DVDD

CVDD

DVDD
EMA_BA[0]/GP1[14]
EMA_BA[1]/UHPI_HHWIL/GP1[13]
EMA_A[10]/GP1[10]
CVDD
EMA_A[0]/GP1[0]

EMA_A[3]/GP1[3]

EMA_A[5]/GP1[5]
EMA_A[6]/GP1[6]

EMA_A[11]/GP1[11]
EMA_A[12]/GP1[12]
DVDD
AXR1[0]/GP4[0]
UART0_RXD/I2C0_SDA/TM64P0_IN12/GP5[8]/BOOT[8]
UART0_TXD/I2C0_SCL/TM64P0_OUT12/GP5[9]/BOOT[9]
AXR1[10]/GP5[10]

AXR1[11]/GP5[11]
SPI1_ENA/UART2_RXD/GP5[12]
SPI1_SCS[0]/UART2_TXD/GP5[13]
SPI0_SCS[0]/UART0_RTS/EQEP0B/GP5[4]/BOOT[4]

SPI0_CLK/EQEP1I/GP5[2]BOOT[2]
SPI0_ENA/UART0_CTS/EQEP0A/GP5[3]/BOOT[3]
SPI1_SOMI[0]/I2C1/SCL/GP5[5]BOOT[5]
SPI1_SIMO[0]/I2C1/SDA/GP5[6]BOOT[6]

SPI1_CLK/EQEP1S/GP5[7]BOOT[7]
SPI0_SOMI[0]/EQEP0I/GP5[0]BOOT[0]
SPI0_SIMO[0]/EQEP0S/GP5[1]BOOT[1]
EMA_WAIT[0]/UHPI_HRDY/GP2[10]

EMA_CS[3]/AMUTE2/GP2[6]
EMA_OE/UHPI_HDS1/AXR0[13]/GP2[7]
EMA_CS[2]/UHPI_HCS/GP2[5]/BOOT[15]

EMA_A[1]/MMCSD_CLK/UHPI/HCNTL0/GP1[1]
EMA_A[2]/MMCSD_CMD/UHPI/HCNTL1/GP1[2]

85
 RX-A3020/RX-V3073

Pin TYPE PULL

Function Name Detail of Function
No. (1) (2)
1 AXR1[0]/GP4[0] I/O IPD McASP1 serial data
2 UART0_RXD/I2C0_SDA/TM64P0_IN12/GP5[8]/ I IPU BOOT[8]
BOOT[8] I IPU UART0 receive data
I/O IPU I2C0 serial data
I IPU Timer0 lower input
3 UART0_TXD/I2C0_SCL/TM64P0_OUT12/GP5[9]/ I IPU BOOT[9]
BOOT[9] O IPU UART0 transmit data
I/O IPU I2C0 serial clock
O IPU Timer0 lower output
4 AXR1[10]/GP5[10] I/O IPU McASP1 serial data
5 DVDD (I/O supply) PWR 3.3-V I/O supply voltage pins
6 AXR1[11]/GP5[11] I/O IPU McASP1 serial data
7 SPI1_ENA /UART2_RXD/GP5[12] I/O IPU SPI1 enable
I IPU UART2 receive data
8 SPI1_SCS[0] /UART2_TXD/GP5[13] I/O IPU SPI1 chip select
O IPU UART2 transmit data
9 SPI0_SCS[0] /UART0_RTS/EQEP0B/GP5[4]/BOOT[4] I/O IPU SPI0 chip select
I IPU eQEP0B quadrature input
I IPU BOOT[4]
O IPU UART0 ready-to-send output
10 CVDD (Core supply) PWR 1.2-V core supply voltage pins
11 SPI0_CLK/EQEP1I/GP5[2]/BOOT[2] I/O IPD SPI0 clock
I IPD eQEP1 index
I IPD BOOT[2]
12 SPI0_ENA /UART0_CTS/EQEP0A/GP5[3]/BOOT[3] I/O IPU SPI0 enable
I IPU eQEP0A quadrature input
RX-A3020/RX-V3073

I IPU BOOT[3]
I IPU UART0 clear-to-send input
13 SPI1_SOMI[0]/I2C1_SCL/GP5[5]/BOOT[5] I/O IPU SPI1 data/slave-out-master-in
I IPU BOOT[5]
I/O IPU I2C1 serial clock
14 SPI1_SIMO[0]/I2C1_SDA/GP5[6]/BOOT[6] I/O IPU SPI1 data/slave-in-master-out
I IPU BOOT[6]
I/O IPU I2C1 serial Data
15 DVDD (I/O supply) PWR 3.3-V I/O supply voltage pins
16 SPI1_CLK/EQEP1S/GP5[7]/BOOT[7] I/O IPD SPI1 clock
I IPD eQEP1 strobe
I IPD BOOT[7]
17 SPI0_SOMI[0]/EQEP0I/GP5[0]/BOOT[0] I/O IPD SPI0 data/slave-out-master-in
I IPD eQEP0 index
I IPD BOOT[0]
18 SPI0_SIMO[0]/EQEP0S/GP5[1]/BOOT[1] I/O IPD SPI0 data/slave-in-master-out
I IPD eQEP0 strobe
I IPD BOOT[1]
19 EMA_WAIT[0]/ UHPI_HRDY/GP2[10] I IPU EMIFA wait input/interrupt
I/O IPU UHPI ready
20 CVDD (Core supply) PWR 1.2-V core supply voltage pins
21 EMA_CS[3] /AMUTE2/GP2[6] O IPU EMIFA Async chip select
O IPU McASP2 mute output
22 EMA_OE /UHPI_HDS1/AXR0[13]/GP2[7] O IPU EMIFA output enable
I/O IPU UHPI data strobe
23 EMA_CS[2] /UHPI_HCS/GP2[5]/BOOT[15] O IPU EMIFA Async chip select
I IPU BOOT[15]
I/O IPU UHPI chip select
24 EMA_OE/UHPI_HDS1/AXR0[13]/GP2[7] I/O IPU McASP0 serial data
DVDD (I/O supply) PWR 3.3-V I/O supply voltage pins
25 EMA_BA[0]/ GP1[14] O IPU EMIFA bank address
26 EMA_BA[1]/ UHPI_HHWIL/GP1[13] O IPU EMIFA bank address
I/O IPU UHPI half-word identification control
27 EMA_A[10]/ GP1[10] O IPU EMIFA address bus
28 CVDD (Core supply) PWR 1.2-V core supply voltage pins
29 EMA_A[0]/ GP1[0] O IPD EMIFA address bus
30 EMA_A[1]/MMCSD_CLK/UHPI_HCNTL0/GP1[1] O IPU EMIFA address bus
I/O IPU UHPI access control
O IPU MMCSD_CLK
31 EMA_A[2]/MMCSD_CMD/UHPI_HCNTL1/GP1[2] O IPU EMIFA address bus
I/O IPU UHPI access control
I/O IPU MMCSD_CMD
32 EMA_A[3]/ GP1[3] O IPD EMIFA address bus
33 DVDD (I/O supply) PWR 3.3-V I/O supply voltage pins
34 EMA_A[4]/ GP1[4] O IPD EMIFA address bus
35 EMA_A[5]/ GP1[5] O IPD EMIFA address bus
36 EMA_A[6]/ GP1[6] O IPD EMIFA address bus
37 EMA_A[7]/ GP1[7] O IPD EMIFA address bus

86
 RX-A3020/RX-V3073

Pin TYPE PULL

Function Name Detail of Function
No. (1) (2)
38 CVDD (Core supply) PWR 1.2-V core supply voltage pins
39 EMA_A[8]/ GP1[8] O IPU EMIFA address bus
40 EMA_A[9]/ GP1[9] O IPU EMIFA address bus
41 EMA_A[11]/ GP1[11] O IPU EMIFA address bus
42 EMA_A[12]/ GP1[12] O IPU EMIFA address bus
43 DVDD (I/O supply) PWR 3.3-V I/O supply voltage pins
44 EMA_D[0]/MMCSD_DAT[0]/UHPI_HD[0]/GP0[0]/ I/O IPU EMIFA data bus
BOOT[12] I IPU BOOT[12]
I/O IPU UHPI data bus
I/O IPU MMC/SD data
45 EMA_D[1]/MMCSD_DAT[1]/UHPI_HD[1]/GP0[1] I/O IPU EMIFA data bus
I/O IPU UHPI data bus
I/O IPU MMC/SD data
46 EMA_D[2]/MMCSD_DAT[2]/UHPI_HD[2]/GP0[2] I/O IPU EMIFA data bus
I/O IPU UHPI data bus
I/O IPU MMC/SD data
47 DVDD (I/O supply) PWR 3.3-V I/O supply voltage pins
48 EMA_D[3]/MMCSD_DAT[3]/UHPI_HD[3]/GP0[3] I/O IPU EMIFA data bus
I/O IPU UHPI data bus
I/O IPU MMC/SD data
49 EMA_D[4]/MMCSD_DAT[4]/UHPI_HD[4]/GP0[4] I/O IPU EMIFA data bus
I/O IPU UHPI data bus
I/O IPU MMC/SD data
50 CVDD (Core supply) PWR 1.2-V core supply voltage pins
51 EMA_D[5]/MMCSD_DAT[5]/UHPI_HD[5]/GP0[5] I/O IPU EMIFA data bus
I/O IPU UHPI data bus

RX-A3020/RX-V3073
I/O IPU MMC/SD data
52 EMA_D[6]/MMCSD_DAT[6]/UHPI_HD[6]/GP0[6] I/O IPU EMIFA data bus
I/O IPU UHPI data bus
I/O IPU MMC/SD data
53 DVDD (I/O supply) PWR 3.3-V I/O supply voltage pins
54 EMA_D[7]/MMCSD_DAT[7]/UHPI_HD[7]/GP0[7]/ I/O IPU EMIFA data bus
BOOT[13] I IPU BOOT[13]
I/O IPU UHPI data bus
I/O IPU MMC/SD data
55 EMA_WE /UHPI_HRW/AXR0[12]/GP2[3]/BOOT[14] O IPU EMIFA SDRAM write enable
I IPU BOOT[14]
I/O IPU UHPI read/write
I/O IPU McASP0 serial data
56 CVDD (Core supply) PWR 1.2-V core supply voltage pins
57 EMB_CAS O IPU EMIFB column address strobe
58 DVDD (I/O supply) PWR 3.3-V I/O supply voltage pins
59 EMB_WE O IPU EMIFB write enable
60 EMB_WE_DQM[0] /GP5[15] O IPU EMIFB write enable/data mask for EMB_D.
61 CVDD (Core supply) PWR 1.2-V core supply voltage pins
62 EMB_D[7]/GP6[7] I/O IPD EMIFB SDRAM data bus
63 EMB_D[6]/GP6[6] I/O IPD EMIFB SDRAM data bus
64 EMB_D[5]/GP6[5] I/O IPD EMIFB SDRAM data bus
65 DVDD (I/O supply) PWR 3.3-V I/O supply voltage pins
66 EMB_D[4]/GP6[4] I/O IPD EMIFB SDRAM data bus
67 CVDD (Core supply) PWR 1.2-V core supply voltage pins
68 EMB_D[3]/GP6[3] I/O IPD EMIFB SDRAM data bus
69 CVDD (Core supply) PWR 1.2-V core supply voltage pins
70 EMB_D[2]/GP6[2] I/O IPD EMIFB SDRAM data bus
71 DVDD (I/O supply) PWR 3.3-V I/O supply voltage pins
72 EMB_D[1]/GP6[1] I/O IPD EMIFB SDRAM data bus
73 EMB_D[0]/GP6[0] I/O IPD EMIFB SDRAM data bus
74 EMB_D[15]/GP6[15] I/O IPD EMIFB SDRAM data bus
75 DVDD (I/O supply) PWR 3.3-V I/O supply voltage pins
76 EMB_D[14]/GP6[14] I/O IPD EMIFB SDRAM data bus
77 CVDD (Core supply) PWR 1.2-V core supply voltage pins
78 EMB_D[13]/GP6[13] I/O IPD EMIFB SDRAM data bus
79 EMB_D[12]/GP6[12] I/O IPD EMIFB SDRAM data bus
80 EMB_D[11]/GP6[11] I/O IPD EMIFB SDRAM data bus
81 DVDD (I/O supply) PWR 3.3-V I/O supply voltage pins
82 EMB_D[10]/GP6[10] I/O IPD EMIFB SDRAM data bus
83 EMB_D[9]/GP6[9] I/O IPD EMIFB SDRAM data bus
84 EMB_D[8]/GP6[8] I/O IPD EMIFB SDRAM data bus
85 EMB_WE_DQM[1] /GP5[14] O IPU EMIFB write enable/data mask for EMB_D
86 EMB_CLK O IPU EMIF SDRAM clock
87 DVDD (I/O supply) PWR 3.3-V I/O supply voltage pins
88 EMB_SDCKE I/O IPU EMIFB SDRAM clock enable
89 EMB_A[12]/GP3[13] O IPD EMIFB SDRAM row/column address bus
90 DVDD (I/O supply) PWR 3.3-V I/O supply voltage pins

87
 RX-A3020/RX-V3073

Pin TYPE PULL

Function Name Detail of Function
No. (1) (2)
91 EMB_A[11]/GP7[13] O IPD EMIFB SDRAM row/column address bus
92 EMB_A[9]/GP7[11] O IPD EMIFB SDRAM row/column address bus
93 CVDD (Core supply) PWR 1.2-V core supply voltage pins
94 EMB_A[8]/GP7[10] O IPD EMIFB SDRAM row/column address bus
95 EMB_A[7]/GP7[9] O IPD EMIFB SDRAM row/column address bus
96 EMB_A[6]/GP7[8] O IPD EMIFB SDRAM row/column address bus
97 EMB_A[5]/GP7[7] O IPD EMIFB SDRAM row/column address bus
98 EMB_A[4]/GP7[6] O IPD EMIFB SDRAM row/column address
99 DVDD (I/O supply) PWR 3.3-V I/O supply voltage pins
100 EMB_A[3]/GP7[5] O IPD EMIFB SDRAM row/column address
101 EMB_A[2]/GP7[4] O IPD EMIFB SDRAM row/column address
102 EMB_A[1]/GP7[3] O IPD EMIFB SDRAM row/column address
103 EMB_A[0]/GP7[2] O IPD EMIFB SDRAM row/column address
104 CVDD (Core supply) PWR 1.2-V core supply voltage pins
105 EMB_A[10]/GP7[12] O IPD EMIFB SDRAM row/column address bus
106 EMB_BA[1]/GP7[0] O IPU EMIFB SDRAM bank address
107 EMB_BA[0]/GP7[1] O IPU EMIFB SDRAM bank address
108 EMB_CS[0] O IPU EMIFB SDRAM chip select 0
109 DVDD (I/O supply) PWR 3.3-V I/O supply voltage pins
110 EMB_RAS O IPU EMIFB SDRAM row address strobe
111 AXR0[0]/AFSR2/GP3[0] I/O IPD McASP0 serial data
O IPD McASP2 serial data
112 AXR0[1]/ACLKX2/GP3[1] I/O IPD McASP0 serial data
O IPD McASP2 transmit bit clock
113 AXR0[2]/AXR2[3]/GP3[2] I/O IPD McASP0 serial data
O IPD McASP2 serial data
RX-A3020/RX-V3073

114 CVDD (Core supply) PWR 1.2-V core supply voltage pins
115 AXR0[3]/AXR2[2]/GP3[3] I/O IPD McASP0 serial data
O IPD McASP2 serial data
116 AXR0[4]/ AXR2[1]/GP3[4] I/O IPD McASP0 serial data
O IPD McASP2 serial data
117 AXR0[5]/AFSX2/GP3[5] I/O IPD McASP0 serial data
O IPD McASP2 transmit frame sync
118 AXR0[6]/ACLKR2/GP3[6] I/O IPD McASP0 serial data
I/O IPD McASP2 receive bit clock
119 DVDD (I/O supply) PWR 3.3-V I/O supply voltage pins
120 AXR0[7]/GP3[7] I/O IPD McASP0 serial data
121 AXR0[8]/GP3[8] I/O IPU McASP0 serial data
122 UART1_RXD/AXR0[9]/GP3[9] I IPD UART1 receive data
(3) I/O IPD McASP0 serial data
123 UART1_TXD/AXR0[10]/GP3[10] O IPD UART1 transmit data
(3) I/O IPD McASP0 serial data
124 AXR0[11]/ AXR2[0]/GP3[11] I/O IPD McASP0 serial data
O IPD McASP2 serial data
125 AHCLKX0/AHCLKX2/USB_REFCLKIN/GP2[11] I/O IPD McASP0 transmit master clock
O IPD McASP2 transmit master clock
I IPD USB_REFCLKIN. Optional 48 MHz clock input
126 ACLKX0/ECAP0/APWM0/GP2[12] I/O IPD Enhanced capture 0/input or auxiliary PWM 0 output
I/O IPD McASP0 transmit bit clock
127 AFSX0/GP2[13]/BOOT[10] I IPD BOOT[10]
I/O IPD McASP0 transmit frame sync
128 DVDD (I/O supply) PWR 3.3-V I/O supply voltage pins
129 AHCLKR0/GP2[14]/BOOT[11] I IPD BOOT[11]
I/O IPD McASP0 receive master clock
130 ACLKR0/ECAP1/APWM1/GP2[15] I/O IPD Enhanced capture 1/input or auxiliary PWM 1 output
I/O IPD McASP0 receive bit clock
131 AFSR0/GP3[12] I/O IPD McASP0 receive frame sync
132 AMUTE1/EPWMTZ/GP4[14] I/O IPD eHRPWM0 trip zone input
I/O IPD eHRPWM1 trip zone input
I/O IPD eHRPWM2 trip zone input
O IPD McASP1 mute output
133 RSV2 PWR Reserved. For proper device operation, this pin must be tied directly to CVDD
134 USB0_VDDA12 (4) PWR USB0 PHY 1.2-V LDO output for bypass cap
135 USB0_VDDA18 PWR USB0 PHY 1.8-V supply input
136 NC – –
137 USB0_DP A USB0 PHY data plus
138 USB0_DM A USB0 PHY data minus
139 NC – –
140 USB0_VDDA33 PWR USB0 PHY 3.3-V supply
141 PLL0_VDDA PWR PLL analog VDD (1.2-V filtered supply)
142 PLL0_VSSA GND PLL analog VSS (for filter)
143 OSCIN I Oscillator input
144 OSCVSS GND Oscillator ground (for filter only)
145 OSCOUT O Oscillator output

88
 RX-A3020/RX-V3073

Pin TYPE PULL

Function Name Detail of Function
No. (1) (2)
146 RESET I Device reset input
147 CVDD (Core supply) PWR 1.2-V core supply voltage pins
148 RTC_XI I Low-frequency (32-kHz) oscillator receiver for real-time clock
149 RTC_CVDD PWR RTC module core power ( isolated from rest of chip CVDD)
150 TRST I IPD JTAG test reset
151 DVDD (I/O supply) PWR 3.3-V I/O supply voltage pins
152 TMS I IPU JTAG test mode select
153 TDI I IPU JTAG test data input
154 CVDD (Core supply) PWR 1.2-V core supply voltage pins
155 TCK I IPU JTAG test clock
156 TDO O IPD JTAG test data output
157 GP7[14] (5) I/O IPD General-Purpose IO signal
158 DVDD (I/O supply) PWR 3.3-V I/O supply voltage pins
159 CVDD (Core supply) PWR 1.2-V core supply voltage pins
160 AHCLKX1/EPWM0B/GP3[14] I/O IPD eHRPWM0 B output
I/O IPD McASP1 transmit master clock
161 CVDD (Core supply) PWR 1.2-V core supply voltage pins
162 ACLKX1/EPWM0A/GP3[15] I/O IPD eHRPWM0 A output
I/O IPD McASP1transmit bit clock
163 AFSX1/EPWMSYNCI/EPWMSYNCO/GP4[10] I/O IPD Sync input to eHRPWM0 module or sync output to external PWM
I/O IPD McASP1 transmit frame sync
164 DVDD (I/O supply) PWR 3.3-V I/O supply voltage pins
165 ACLKR1/ECAP2/APWM2/GP4[12] I/O IPD Enhanced capture 2/input or auxiliary PWM 2 output
I/O IPD McASP1 receive bit clock
166 AFSR1/GP4[13] I/O IPD McASP1 receive frame sync
167 CVDD (Core supply) PWR 1.2-V core supply voltage pins

RX-A3020/RX-V3073
168 AXR1[8]/EPWM1A/GP4[8] I/O IPD eHRPWM1 A (with high-resolution)
I/O IPD McASP1 serial data
169 AXR1[7]/EPWM1B/GP4[7] I/O IPD eHRPWM1 B
I/O IPD McASP1 serial data
170 AXR1[6]/EPWM2A/GP4[6] I/O IPD eHRPWM2 A (with high-resolution)
I/O IPD McASP1 serial data
171 AXR1[5]/EPWM2B/GP4[5] I/O IPD eHRPWM2 B
I/O IPD McASP1 serial data
172 DVDD (I/O supply) PWR 3.3-V I/O supply voltage pins
173 AXR1[4]/EQEP1B/GP4[4] I IPD eQEP1B quadrature input
I/O IPD McASP1 serial data
174 AXR1[3]/EQEP1A/GP4[3] I IPD eQEP1A quadrature input
I/O IPD McASP1 serial data
175 AXR1[2]/GP4[2] I/O IPD McASP1 serial data
176 AXR1[1]/GP4[1] I/O IPD McASP1 serial data

(1) I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal.
Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the the signal name highlighted
in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured function supports
high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different types (ie., input versus
output), the table reflects the pin function direction for that particular peripheral.
(2) IPD = Internal Pulldown resistor, IPU = Internal Pullup resistor
(3) 122, 123 pin: As these signals are internally pulled down while the device is in reset, it is necessary to externally pull them high with resistors if UART1
boot mode is used.
(4) 134 pin: Core power supply LDO output for USB PHY. This pin must be connected via a 0.22-mF capacitor to VSS. When the USB peripheral is not
used, the USB_VDDA12 signal should still be connected via a 1-mF capacitor to VSS.
(5) 157 pin: GP7[14] is initially configured as a reserved function after reset and will not be in a predictable state. This signal will only be stable after
the GPIO configuration for this pin has been completed. Users should carefully consider the system implications of this pin being in an
unknown state after reset.

89
 RX-A3020/RX-V3073

IC951: DM860A (DIGITAL P.C.B.)

Network microprocessor
* No replacement part available. / サービス部品供給なし

General Purpose
Security Engine Timing Engine
RESET, BOOT_SEL on-chip RAM CLOCKS
Reset, Boot, OTP 2 PLLs, 3 DCOs
64 kBytes

master DMA
AV0 Port slave
4xAudio, 1xVideo 2 Forwarding Units
I2S, I8S, DSD, video 64 Contexts

AV2 Port S ARM 926EJ-S

4xAudio
I2S, I8S, DSD 240 MHz
Y
I-cache 16 kByte
slave master
AV3 Port S D-cache 16 kByte
2xAudio I2S, I8S, DSD,
SPDIF
T
slave Interrupt Controller GPIO
AV4 Port Watchdog, 2 Timer
2xAudio I2S, I8S, DSD, E
SPDIF, ADAT
M RTSP Processor
160 MHz
stereo master
Audio PWM-DAC slave I-cache 16 kByte

TCM 48 kByte

Memory Bus, SD/SRAM and System slave

System Extension Extension Controller Audio Engine
B 160 MHz
master
slave slave I-cache 4 kByte
LCD LCD Controller U
TCM 10 kByte
RX-A3020/RX-V3073

USB 2.0 slave master Ethernet MAC

USB USB (R/SSS)MII
OTG
10/100 Mbps
PHY 8 kByte RAM

slave slave
UART 2 x UART-1 NAND FLASH NAND

slave slave
SPI SPI SSM Controller SSM

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

VDD33 VSS33
A USBDN n.c. n.c. VDD33 RFCLKP RFRXQP RFRXIP HIGHZ SSMD0 SSMD4 SSMCMD RXD1 TDO TDI A0 A1 A
USBC USBC

VDD33 VSS33
B USBDP n.c. n.c. VSS RFCLKN RFRXQN RFRXIN TEST1 SSMD1 SSMD5 TXD1 RXD0 TMS SPICLK SPINCS1 A2 B
USBT USBT

VSS12 NRES12
C USBREXT USBXO USBXI VSS RREF n.c. n.c. SSMCLK SSMD2 SSMD6 TXD0 TCK SPINCS0 A3 A4 A5 C
USB OUT

VDD12 NRES33 NRES33 NRES12

D USBVBUS USBATST VDD33 VDD12 SSMWP SSMCP SSMD3 SSMD7 NRESET SPIDI SPIDO A6 A7 A8 D
USB OUT REF REF

VSS33 USBVB VDD12 VDD12 VDD12 VDD12

E USBID NC VDD33IO VDD33IO VDD33IO VDD33IO A9 A10 A11 A12 E
RTC USDRV CORE CORE CORE CORE

VDD33 VDD33 VDD12

F RTCXIN NC VDD33IO VSS VSS VSS VSS VSS VSS VSS VSS A13_RAS A14_CAS A15_BA0 A16_BA1 F
RTC PLL CORE

VDD12 VSS33 VDD12 A17_DQ A18_DQ

G RTCXOUT NC VDD33IO VSS VSS VSS VSS VSS VSS VSS VSS A19 A20 G
DCO PLL CORE M0 M1

VSS12 VSS12 VDD12 VDD12

H NC VSS VSS VSS VSS VSS VSS VSS VSS VDD33IO A21 A22 A23 NCS3 H
DCO PLL PLL CORE

VDD12
J PDOUT1 VCO1 XTALO NC VSS VSS VSS VSS VSS VSS VSS VSS VDD33IO NCS0 NCS1 NCS2 MEMCKE J
CORE

VDD12
K PDOUT0 VCO0 XTALI AOUTLP VDD33IO VSS VSS VSS VSS VSS VSS VSS VSS MEMCLK NWE NOE NWAIT K
CORE

VDD12
L AV0CLK AOUTLN AOUTRN AOUTRP VDD33IO VSS VSS VSS VSS VSS VSS VSS VSS D3 D2 D1 D0 L
CORE

AV0 AV0 AV0 AV0 VDD12

M VSS VSS VSS VSS VSS VSS VSS VSS VDD33IO D7 D6 D5 D4 M
CTRL0 CTRL1 CTRL2 DATA3 CORE

AV0 AV0 AV0 AV1 VDD12

N VSS VSS VSS VSS VSS VSS VSS VSS VDD33IO D11 D10 D9 D8 N
DATA2 DATA1 DATA0 DATA3 CORE

AV1 AV1 AV1 AV2 VDD12 VDD12 VDD12 VDD12

P VDD33IO VDD33IO VDD33IO VDD33IO FD0 FD1 D13 D12 P
DATA2 DATA1 DATA0 DATA3 CORE CORE CORE CORE

AV2 AV2 AV3 LCD

R AV2CLK AV3CLK LCDD11 LCDD7 LCDD3 VPP MIITXEN MIITXCLK MIIRXER MIICRS FD2 FD3 FD4 D14 R
CTRL1 DATA2 DATA1 CTRL0

AV2 AV2 AV3 AV3 LCD MII

T LCDD14 LCDD10 LCDD6 LCDD2 LCDCLK MIIITXER MIIRXCLK MIICOL FD5 FD6 FD7 D15 T
CTRL0 DATA1 CTRL1 DATA0 CTRL1 RXDV

AV2 AV3 AV4 LCD

U LCDD16 LCDD13 LCDD9 LCDD5 LCDD1 MIITXD0 MIITXD2 MIIRXD0 MIIRXD2 MIIMDIO NFCE0 FCLE NFWE NFRB U
DATA0 CTRL0 DATA1 CTRL2

AV4 LCD MIIPHY

V NC LCDD17 LCDD15 LCDD12 LCDD8 LCDD4 LCDD0 MIITXD1 MIITXD3 MIIRXD1 MIIRXD3 MIIMDC NFWP NFRE FALE V
DATA0 CTRL3 CLK
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

90
 RX-A3020/RX-V3073

AV-Port 0
Pin No. Function Name I/O Detail of Function
M4
N1 Audio/video data.
AV0DATA[3:0] I/O
N2 Several formats are supported.
N3
N4 Video data, together with AV0DATA[3:0]:
P1 AV0DATA[3:0] = video[3:0]
AV1DATA[3:0] I/O
P2 AV1DATA[3:0] = video[7:4]
P3
Data clock. Depending on the AV-Port 0 configuration, this clock is a bit- or byte-clock which is used to
L1 AV0CLK I/O
transmit or receive the AV0DATA[*] synchronously.
Configurable sync signal:
M1 AV0CTRL0 I/O • Serial audio formats: LRCK input or output.
• Video formats: PSYNC input or output.
Configurable sync signal:
M2 AV0CTRL1 I/O • Serial audio formats: Master clock output.
• Video formats: DVALID input or output.
Configurable sync signal:
M3 AV0CTRL2 I/O
• Video formats: FSYNC input or output.

AV-Port 2
Pin No. Function Name I/O Detail of Function

RX-A3020/RX-V3073
P4
R3 Audio data.
AV2DATA[3:0] I/O
T2 Several formats are supported.
U1
Data clock. Depending on the AV-Port 2 configuration this clock is a bit-clock which is used to transmit or
R1 AV2CLK I/O
receive the AV2DATA[*] synchronously.
Configurable sync signal:
T1 AV2CTRL0 I/O
Serial audio formats: LRCK input or output.
Configurable sync signal:
R2 AV2CTRL1 I/O
Serial audio formats: Master clock output.

AV-Port 3
Pin No. Function Name I/O Detail of Function
R5 Audio data.
AV3DATA[1:0] I/O
T4 Several formats are supported.
Data clock. Depending on the AV-Port 3 configuration this clock is a bit-clock which is used to transmit or
R4 AV3CLK I/O
receive the AV3DATA[*] synchronously.
Configurable sync signal:
U2 AV3CTRL0 I/O
Serial audio formats: LRCK input or output.
Configurable sync signal:
T3 AV3CTRL1 I/O
Serial audio formats: Master clock output.

AV-Port 4
Pin No. Function Name I/O Detail of Function
U3 Audio data.
AV4DATA[1:0] I/O
V2 Several formats are supported.

PWM-DAC
Pin No. Function Name I/O Detail of Function
K4 AOUTLP O Left channel PWM output (positive).
L2 AOUTLN O Left channel PWM output (negative).
L4 AOUTRP O Right channel PWM output (positive).
L3 AOUTRN O Right channel PWM output (negative).

UART Interface
Pin No. Function Name I/O Detail of Function
B14 RXD0 I UART-0 receive signal.
C13 TXD0 O UART-0 transmit signal.
A14 RXD1 I UART-1 receive signal.
B13 TXD1 O UART-1 transmit signal.

91
 RX-A3020/RX-V3073

Serial Peripheral Interface (SPI)

Pin No. Function Name I/O Detail of Function
D14 SPIDIN I SPI data receive.
D15 SPIDOUT O SPI data transmit.
B16 SPICLK I/O SPI clock.
Multi-master mode: Chip-select input (used to detect bus conflict).
C15 SPINCS0 I/O Master only mode: Chip-select 1 output.
Slave mode: Chip-select input.
Multi-master mode: Chip-select 2 output.
B17 SPINCS1 I/O Master only mode: Chip-select 2 output.
Slave mode: Not used.

External Memory Interface

Pin No. Function Name I/O Detail of Function
T18
R18
P17
P18
N15
N16
N17
N18
RX-A3020/RX-V3073

D[15:0] I/O Data bus for external memory and peripheral access.
M15
M16
M17
M18
L15
L16
L17
L18
E18
E17
E16
E15
D18
D17
D16 A[12:0] O Address bus for external memory and peripheral access.
C18
C17
C16
B18
A18
A17
SRAM: Address output
F15 A13_RAS O
SDRAM: Row access strobe
SRAM: Address output
F16 A14_CAS O
SDRAM: Column access strobe
SRAM: Address output
F17 A15_BA0 O
SDRAM: Bank select
SRAM: Address output
F18 A16_BA1 O
SDRAM: Bank select
SRAM: Address output
G15 A17_DQM0 O
SDRAM: Data mask
SRAM: Address output
G16 A18_DQM1 O
SDRAM: Data mask
H17
H16
H15 A[23:19] O Address bus for external memory and peripheral access.
G18
G17

92
 RX-A3020/RX-V3073

Pin No. Function Name I/O Detail of Function

H18 Chip select signals. The active memory range for NCS[n] (active low) can be configured.
J17 • NCS[0] supports SRAM, can be used for booting.
J16 NCS[3:0] O • NCS[1] supports SDRAM or SRAM.
J15 • NCS[2] supports SRAM.
• NCS[3] supports SRAM.
K17 NOE O Output enable, asserted (low) for read operations.
K16 NWE O Write enable, asserted (low) for write operations.
K18 NWAIT I External wait line. If NWAIT is asserted, memory access will be stalled. Can be configured as either low-
active (default) or high-active.
K15 MEMCLK O SDRAM system clock.
J18 MEMCKE O SDRAM clock enable.

NAND-Flash Interface
Pin No. Function Name I/O Detail of Function
T17
T16
T15
R17
FD[7:0] I/O Bi-directional data bus.
R16

RX-A3020/RX-V3073
R15
P16
P15
V18 FALE O Address latch enable; pull-up/down defines boot mode.
U16 FCLE O Command latch enable; pull-up/down defines boot mode.
U15 NFCE0 O Chip-enable, low-active.
U18 NFRB I Ready/busy. NAND flash is busy when NFRB is low.
V17 NFRE O Read enable, low-active.
U17 NFWE O Write enable, low-active.
V16 NFWP O Write protect, low-active.

Ethernet MAC-Phy Interface (MII)

Pin No. Function Name I/O MII RMII SMII
U14 MIIDIO I/O Management data Management data
V14 MIIMDC O Management clock Management clock
V13 MIIRXD[3] I RxD 3 RxD 1
U13 MIIRXD[2] I RxD 2 RxD 0
V12 MIIRXD[1] I RxD 1 Rx-Sync
U12 MIIRXD[0] I RxD 0 RxD
T12 MIIRXCLK I Receive clock Receive clock
R13 MIIRXER I Receive error Receive error
T14 MIIRXDV I Receive data valid Carrier sense/data valid
V11 MIITXD[3] O TxD 3 TxD 1
U11 MIITXD[2] O TxD 2 TxD 0
V10 MIITXD[1] O TxD 1 Tx-Sync
U10 MIITXD[0] O TxD 0 TxD
R12 MIITXCLK I Transmit clock Transmit clock
T11 MIITXER O Transmit error
R11 MIITXEN O Transmit data enable Transmit data enable
T13 MIICOL I MII ethernet collision
R14 MIICRS I MII carrier sense
V15 MIIPHYCLK O 25.000 MHz clock 50.000 MHz clock 125.000 MHz clock

93
 RX-A3020/RX-V3073

USB 2.0 OTG

Pin No. Function Name I/O Detail of Function
B1 USBD+ I/O Positive data line that is connected to the serial USB cable.
A1 USBD– I/O Negative data line that is connected to the serial USB cable.
E2 USBID I USB ID pin of mini-AB receptacle.
C2 USBREXT I External bias resistor (2K7, 1%); connect resistor to VSSUSB.
D2 USBVBUS I VBUS voltage sense.
E3 USBVBUSDRV O Control signal to control VBUS 5V voltage source.
C4 USBXTALI I Oscillator circuit input for a 24.000 MHz crystal (optional).
Without external crystal, pull this pin to GND.
C3 USBXTALO O Oscillator circuit output for a 24.000 MHz crystal (optional).
Without external crystal, leave this pin open.
D3 USBATST – Do not connect.

Power-on Reset Pins

Pin No. Function Name I/O Detail of Function
D6 NRES12REF I Voltage reference input. NRES12OUT is release when this input voltage exceeds VTH12.
C5 NRES12OUT O Open-drain reset (active low) for 1.2V core power supply.
D5 NRES33REF I Voltage reference input. NRES33OUT is release when this input voltage exceeds VTH33.
D4 NRES33OUT O Open-drain reset (active low) for 3.3V core power supply
RX-A3020/RX-V3073

Real-Time Clock (RTC) Pins (RTC is Not Supported)

Pin No. Function Name I/O Detail of Function
F2 RTCXIN I No connection. Leave this pin open circuit.
G2 RTCXOUT O No connection. Leave this pin open circuit.
F1 VDD33RTC Power No connection. Leave this pin open circuit.
E1 VSS33RTC Power Ground (0 V) for RTC

LCD Interface

LCD STN
LCD STN LCD STN color
Pin No. Function Name I/O TFT Mode monochrome LCD STN color
monochrome (bias)
(double)
V3 LCDD[17] O RED5
U4 LCDD[16] O RED4
V4 LCDD[15] O RED3
T5 LCDD[14] O RED2
U5 LCDD[13] O RED1
V5 LCDD[12] O (RED0)
R6 LCDD[11] O GREEN5
T6 LCDD[10] O GREEN4
U6 LCDD[9] O GREEN3
V6 LCDD[8] O GREEN2
R7 LCDD[7] O GREEN1 DATAHIGH3 DATA7 DATA7
T7 LCDD[6] O GREEN0 DATAHIGH2 DATA6 DATA6
U7 LCDD[5] O BLUE5 DATAHIGH1 DATA5 DATA5
V7 LCDD[4] O BLUE4 DATAHIGH0 DATA4 DATA4
R8 LCDD[3] O BLUE3 DATA3 DATALOW3 DATA3 DATA3
T8 LCDD[2] O BLUE2 DATA2 DATALOW2 DATA2 DATA2
U8 LCDD[1] O BLUE1 DATA1 DATALOW1 DATA1 DATA1
V8 LCDD[0] O (BLUE0) DATA0 DATALOW0 DATA0 DATA0
T10 LCDCLK O Byte clock CL2 CL2 CL2 CL2
V9 LCDCTRL[3] O Display off Display off Display off Display off Display off
U9 LCDCTRL[2] O Vsync FLM FLM FLM FLM
T9 LCDCTRL[1] O HSync CL1 CL1 CL1 CL1
R9 LCDCTRL[0] O DVALID M/Bias

94
 RX-A3020/RX-V3073

SSM Interface
Pin No. Function Name I/O Detail of Function
D12
C12
B12
A12
SSMD[7:0] I/O Data lines.
D11
C11
B11
A11
C10 SSMCLK O Clock output.
A13 SSMCMD O Command output.
D10 SSMCP I Card power input (high = off).
D9 SSMWP I Write protect input (low = protect).

External PLL Pins

Pin No. Function Name I/O Detail of Function
J2 External oscillator inputs, typically coming from an external VCO. Together with the external loop-filter and
VCO[1:0] I
K2 the internal clock dividers, each PDOUT/VCO pair can form a complete PLL.
J1 Phase discriminator outputs. These signals are charge-pump type outputs.
PDOUT[1:0] O
K1 Each of them can be used to feed the loop-filter of a PLL structure.

RX-A3020/RX-V3073
Global Pins
Pin No. Function Name I/O Detail of Function
Reset (active low). When asserted, the chip is placed in the reset state and the peripheral pins are
configured as inputs. After deassertion of NRESET, the chip is clocked by XTALI and starts booting from the
D13 NRESET I port configured by the FCLE, FALE pins.
The NRESET signal must be asserted after power-up.
K3 XTALI I Oscillator circuit input. Internal system clock will be derived from XTALI (internal clock multiplier).
J3 XTALO O Oscillator circuit output.
C7 RREF I Reference current. Connect a 3.0 k-ohms ±1% resistor to GND.
B10 TEST1 I Reserved. Connect to VDD for normal operation.
A10 HIGHZ I Reserved. Connect to VDD for normal operation.
E4
F4
G4
H4
J4
V1
n.c. – Pins must be left unconnected (18x).
A4
A5
B4
B5
C8
C9

JTAG Interface
Pin No. Function Name I/O Detail of Function
B15 TMS I JTAG mode select.
C14 TCK I JTAG clock.
A16 TDI I JTAG serial data input.
A15 TDO O JTAG serial data output.

95
 RX-A3020/RX-V3073

Power Supply Pins

Pin No. Function Name Detail of Function Pin No. Function Name Detail of Function
A6 K13
E8 L6
E9 L7
E12 L8
E13 L9
F5 L10
G5 L11
H14 L12
J14 L13
VDD33 I/O power supply (+3.3 V).
K5 M6
L5 M7
M14 M8
N14 M9
P6 M10 VSS Ground (0 V).
P7 M11
P10 M12
P11 M13
D7 N6
F6 N7
F7 N8
RX-A3020/RX-V3073

F8 N9
F9 N10
F10 N11
F11 N12
F12 N13
F13 B6
G6 C6
G7 R10 VPP
G8 A2
VDD33USB
G9 B2 Power supply (+3.3 V) for USB interface.
G10 A3 Ground (0 V).
VSS33USB
G11 B3
G12 F3 VDD33PLL Power supply (+3.3V) for PLL.
G13 G3 VSS33PLL Ground (0 V).
H6 E6
H7 E7
H8 E10
H9 VSS Ground (0 V). E11
H10 F14
H11 G14
H12 H5
H13 J5
J6 K14 VDD12 Power supply (+1.2V).
J7 L14
J8 M5
J9 N5
J10 P8
J11 P9
J12 P12
J13 P13
K6 D8
K7 D1 VDD12USB Power supply (+1.2V) for USB interface.
K8 C1 VSS12USB Ground (0 V).
K9 H3 VDD12PLL Power supply (+1.2V) for PLL.
K10 H2 VSS12PLL Ground (0 V).
K11 G1 VDD12DCO Power supply (+1.2V) for DCO.
K12 H1 VSS12DCO Ground (0 V).

96
 RX-A3020/RX-V3073

IC79: R5F6416MADFE (DIGITAL P.C.B.)

Microprocessor
* No replacement part available. / サービス部品供給なし

8 8 8 8 8 8 8 8

Port P0 Port P1 Port P2 Port P3 Port P4 Port P5 Port P6 Port P7

Port P8
Peripheral functions

7
Timer: A/D converter: Clock generator:
Timer A16 bits × 5 timers 10 bits × 1 circuit 4 circuits
Timer B16 bits × 6 timers Standard: 10 inputs - XIN-XOUT
Maximum: 34 inputs - XCIN-XCOUT

P8_5
Three-phase motor - On-chip oscillator
controller - PLL frequency synthesizer
D/A converter:
Serial interface: 8 bits × 2 channels
Watchdog timer:
11 channels

Port P9
X-Y converter: 15 bits
16 bits × 16 bits

8
Multi-master I2C-bus DMAC
interface: CRC calculator (CCITT)
1 channel X16 + X12 + X5 + 1 DMAC II

Port P10
Intelligent I/O R32C/100 Series Microprocessor Core Memory

8
Time Measurement: 16
R2R0 ROM
Wave generation: 24 R2R0
R3R1 FLG
Serial interface: R3R1 INTB

Port P11
R6R4
- Variable-length R6R4
R7R5 ISP RAM
R7R5
A0 USP
synchronous serial I/O A0 PC

8
- IEBus A1
A1
A2 SVF
A2 SVP Multiplier
A3
A3 VCT

RX-A3020/RX-V3073
FB

Port P12
FB
SB
SB Floating-point unit

8
Port P19 Port P18 Port P17 Port P16 Port P15 Port P14 P14_1 Port P13

8 8 8 8 8 5 8

RXD10
TXD10
P12_2
P12_3
P12_4

P16_0

P16_4
P16_5

P11_5

P11_6
RXD9
TXD6

TXD9
CLK6

CLK9
D[10]
D[11]
D[12]
D[13]
D[14]
D[15]

A[10]
A[11]

A[12]
A[13]
A[14]
A[15]

A[16]
A[17]

A[18]

A[19]
VCC
VSS
D[9]

A[0]
A[1]
A[2]
A[3]
A[4]
A[5]
A[6]
A[7]

A[8]

A[9]
132
131
130
129
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
D[8] 133 88 A[20]
D[7] 134 87 A[21]
D[6] 135 86 A[22]
D[5] 136 85 CS0
D[4] 137 84 P19_2
P19_1 138 83 P17_0
P11_4 139 82 P17_1
P19_0 140 81 P17_2
P11_3 141 80 P17_3
RXD8 142 79 P19_3
P11_1 143 78 P12_5
TXD8 144 77 P12_6
P18_7 145 76 P12_7
P18_6 146 75 WR/P5_0
P18_5 147 74 NC(BC1)
P18_4 148 73 RD
P18_3 149 72 NC(BCLK)
P18_2 150 71 P13_0
D[3] 151
IC79 70 P13_1
D[2] 152 69 VCC
D[1] 153 68 P13_2
D[0] 154 67 VSS
P15_7 155 66 P13_3
P15_6 156 65 CS1
P15_5 157 64 P5_5
P15_4 158 63 CS2
R5F6416MADFE
P15_3 159 62 CS3
P15_2 160 61 P19_4
IIO0_1 161 60 ISTXD2
VSS 162 59 ISRXD2
P15_0 163 58 ISCLK2
VCC 164 57 P13_7
P10_7 165 56 P19_5
AN_6 166 55 P6_0
AN_5 167 54 CLK0
AN_4 168 53 RXD0
AN_3 169 52 TXD0
AN_2 170 51 P6_4
AN_1 171 50 CLK1
AVSS 172 49 P11_7
P10_0 173 48 RXD1
VREF 174 47 P14_7
AVCC 175 46 TXD1
SCL4/RXD4 176 45 SDA2
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
1
2
3
4
5
6
7
8
9
SDA4/TXD4
P9_5
P9_4
DA0
SDA3
SCL3
P9_0
P19_7
INT8
P19_6
INT7
INT6
P14_3
VDC0
P14_1
VDC1
NSD
CNVSS
P8_7
P8_6
RESET
XOUT
VSS
XIN
VCC
NMI
INT2
INT1
INT0
TA4IN
SCL5
P18_1
P18_0
TA3IN
SDA5
TA2IN
P7_4
P17_7
P17_6
P17_5
P17_4
TA1IN
P7_2
SCL2

97
 RX-A3020/RX-V3073

Related Power Supply

Pin
Port Name Function Name ON OFF Detail of Function
No.
I/O Logic I/O Logic
SRXD4/SDA4/TXD4/ HDR_MOSI PRY O Data O Low HD Radio transmission data (U model)
1
ANEX1/P9_6 TUN_SDA PRY I/O Data O Low Tuner I2C data (C, R, T, K, A, B, G, F, L, S, J models)
2 CLK4/ANEX0/P9_5 VOL1_SCK PRY/DSP_PON O Clock O Low VOL1 (R2A15220FP #1) communication clock
N_CTS4/N_N_RTS4/N_
3 VOL_MOSI PRY/DSP_PON O Data O Low VOL1/VOL2/VOL3 communication data
SS4/TB4IN/DA1/P9_4
N_CTS3/N_N_RTS3/N_
4 AMP_LMT PRY O D/A I --- Limiter control
SS3/TB3IN/DA0/P9_3
IEOUT/ISTXD2/OUTC2_0/
5 SRXD3/SDA3/TXD3/TB2IN/ HDMI_SDA HDMI_PON I/O Data O Low HDMI 400k I2C data
P9_2
IEIN/ISRXD2/STXD3/SCL3/
6 HDMI_SCL HDMI_PON O Clock O Low HDMI 400k I2C clock
RXD3/TB1IN/P9_1
7 CLK3/TB0IN/P9_0 VOL2_SCK PRY/DSP_PON O Clock O Low VOL2 (R2A15220FP #2) communication clock
8 P19_7 VOL3_SCK PRY/DSP_PON O Clock O Low VOL3 (NJU7313AM) communication clock
9 N_INT8/P14_6 HAU_N_INT HDMI_PON I L act O Low Mute signal from HDMI, RX1 and RX2
10 P19_6 FLD_N_RST FLD_PON O L act O Low FLD reset
11 N_INT7/P14_5 HTX1_N_INT HDMI_PON I L act O Low HDMI TX CEC interrupt
12 N_INT6/P14_4 PWR_DET AC I L act I --- AC power detect
13 P14_3 FLD_N_CS FLD_PON O L act O Low FLD chip select
14 VDC0 VDC0 ---
P14_1 (for exclusive use of
15 I_PRT PRY I H act I --- Current protection
the input)
16 VDC1 VDC1 ---
17 NSD NSD Debugger
18 CNVSS DBG_CNVSS ---
19 XCIN/P8_7 MIC_N_DET DSP_PON I L act O Low Microphone detection
RX-A3020/RX-V3073

20 XCOUT/P8_6 PD_LED PRY O H act O Low Pure direct LED

21 RESET MCPU_N_RST ---
22 XOUT XOUT ---
23 VSS VSS ---
24 XIN XIN ---
25 VCC VCC ---
26 NMI/P8_5 NMI ---
Both
27 N_INT2/P8_4 WAKEUP_INT AC I O Low Power switch, MISO interrupt of RS-232C (Sleep return)
edges
28 N_INT1/P8_3 REM_IN2 AC I L act O Low Remote control pulse input 2
29 N_INT0/P8_2 REM_IN1 AC I L act O Low Remote control pulse input 1
UD0B/UD1B/IIO1_5/N_ – AC O Low O Low No used (U model)
30 RTS5/N_CTS5/N_SS5/U/ Interrupt from TUNER
TUN_N_INT PRY I L act O Low
TA4IN/P8_1 (C, R, T, K, A, B, G, F, L, S, J models)
UD0A/UD1A/RXD5/SCL5/
31 FHDMI_SCL HDMI_PON O Clock O Low HDMI switcher 100k I2C clock
STXD5/U/TA4OUT/P8_0
32 P18_1 FLD_PON FLD_PON O H act O Low FL driver +3.3V power supply control
33 P18_0 STBY_LED AC O H act O Low Standby LED control
UD0B/UD1B/IIO1_4/CLK5/
34 HSW_N_INT HDMI_PON I L act O Low ADV7630 1, 2 interrupt
TA3IN/P7_7
UD0A/UD1A/IIO1_3/N_
RTS8/N_CTS8/TXD5/
35 FHDMI_SDA HDMI_PON I/O Data O Low HDMI switcher 100k I2C data
SDA5/SRXD5/TA3OUT/
P7_6
IIO1_2/RXD8/W/TA2IN/
36 DAU_N_INT DSP_PON I L act O Low Interrupt from DIR1, DIR2 and DSP
P7_5
IIO1_1/CLK8/W/TA2OUT/
37 DIR2_N_INT DSP_PON I L act O Low Interrupt from DIR2 (for DAU_N_INT distinction)
P7_4
38 P17_7 ISEL_RA AC I I --- Input selector A
39 P17_6 ISEL_RB AC I I --- Input selector B
40 P17_5 VOL_RA AC I I --- Volume A
41 P17_4 VOL_RB AC I I --- Volume B
IIO1_0/TXD8/N_SS2/N_
42 RTS2/N_CTS2/V/TA1IN/ HRX_N_INT HDMI_PON I L act O Low HDMI RX (ADV7619) interrupt
P7_3
43 CLK2/V/TA1OUT/P7_2 NCPU_SPI_REQ NCPU_PON I H act O Low BridgeCO request
MSCL/IEIN/ISRXD2/
OUTC2_2/IIO1_7/STXD2/
44 DV_SCL VID_PON O Clock O Low D-VIDEO/A-VIDEO 400k I2C clock
SCL2/RXD2/TA0IN/TB5IN/
P7_1
TA0OUT/TXD2/SDA2/
45 SRXD2/IIO1_6/OUTC2_0/ DV_SDA VID_PON I/O Data O Low D-VIDEO/A-VIDEO 400k I2C clock
ISTXD2/IEOUT/MSDA/P7_0
46 TXD1/SDA1/SRXD1/P6_7 232C_DBG_MOSI AC O Data O Low RS-232C transmission data / Debug / E8a
47 P14_7 DSP_PON DSP_PON O H act O Low DSP power supply
48 RXD1/SCL1/STXD1/P6_6 232C_DBG_MISO AC I Data O Low RS-232C reception data / Debug / E8a
49 P11_7 DAC_N_CS DSP_PON O L act O Low DAC chip select
50 CLK1/P6_5 DBG_SCK AC I Clock O Low E8a
N_CTS1/N_RTS1/N_SS1/
51 DBG_BUSY AC O O Low E8a
OUTC2_1/ISCLK2/P6_4
52 TXD0/SDA0/SRXD0/P6_3 DSP_MOSI DSP_PON O Data O Low DSP/DIR/DAC transmission data

98
 RX-A3020/RX-V3073

Related Power Supply

Pin
Port Name Function Name ON OFF Detail of Function
No.
I/O Logic I/O Logic
TB2IN/RXD0/SCL0/STXD0/
53 DSP_MISO DSP_PON I Data I --- DSP/DIR/DAC reception data
P6_2
54 TB1IN/CLK0/P6_1 DSP_SCK DSP_PON O Clock O Low DSP/DIR/DAC communication clock
TB0IN/N_CTS0/N_RTS0/
55 NCPU_SPI_RDY NCPU_PON I H act O Low BridgeCO data ready
N_SS0/P6_0
56 P19_5 ADC_N_RST DSP_PON O L act O Low ADC reset (power down)
57 D31/OUTC2_7/P13_7 DSP1_N_RST DSP_PON O L act O Low DSP1 reset
D30/OUTC2_1/ISCLK2/
58 –
P13_6
D29/OUTC2_2/ISRXD2/
59 –
IEIN/P13_5
D28/OUTC2_0/ISTXD2/
60 –
IEOUT/P13_4
61 P19_4 EEP_N_CS AC O L act O Low EEPROM chip select
RDY/CS3/N_CTS7/N_
62 FPGA_N_CS HDMI_PON B Bus O Low External bus FPGA chip select
RTS7/P5_7
63 ALE/CS2/RXD7/P5_6 DFF2_N_CS AC B Bus O Low External bus DFF2 chip select
64 HOLD/CLK7/P5_5 DBG_EPM AC I I --- E8a
65 HLDA/CS1/TXD7/P5_4 DFF1_N_CS AC B Bus O Low External bus DFF1 chip select
66 D27/OUTC2_3/P13_3 DSP2_N_SPIRDY DSP_PON I L act O Low DSP2 SPI ready
67 VSS VSS ---
68 D26/OUTC2_6/P13_2 DSP1_N_SPIRDY DSP_PON I L act O Low DSP1 SPI ready
69 VCC VCC ---
70 D25/OUTC2_5/P13_1 DSP2_N_CS DSP_PON O L act O Low DSP2 chip select
71 D24/OUTC2_4/P13_0 DSP1_N_CS DSP_PON O L act O Low DSP1 chip select
72 CLKOUT/BCLK/P5_3 NC(BCLK) AC B Bus O Low External bus

RX-A3020/RX-V3073
73 RD/P5_2 MCBUS_N_RD AC B Bus O Low External bus
74 WR1/BC1/P5_1 NC(BC1) AC B Bus O Low External bus
MCBUS_N_WR HDMI_PON B Bus I --- External bus
75 WR0/WR/P5_0
DBG_N_CE AC I I --- E8a
76 D23/P12_7 MT_DA DSP_PON O H act O Low Mute Digital Audio
77 D22/P12_6 DIR1_N_CS DSP_PON O L act O Low DIR1 chip select
78 D21/P12_5 DIR_N_RST DSP_PON O L act O Low DIR reset
79 P19_3 DIR2_N_CS DSP_PON O L act O Low DIR2 chip select
80 P17_3 HRX2_N_RST HDMI_PON O L act O Low HDMI RX2 reset
81 P17_2 HSW_N_CS HDMI_PON O L act O Low HDMI SW chip select / L=SW1, H=SW2
82 P17_1 NCPU_PON NCPU_PON O H act O Low NET / USB power supply
83 P17_0 NCPU_VBUSDRV NCPU_PON I H act O Low USB VBUS drive
84 P19_2 USB_VBUS_PON NCPU_PON O H act O Low USB VBUS power supply control
CS0/A23/TXD6/SDA6/
85 FLASH_N_CS AC O L act O Low External bus Flash ROM chip select
SRXD6/P4_7
CS1/A22/RXD6/SCL6/
86 A[22] AC B Bus O Low External bus
STXD6/P4_6
87 CS2/A21/CLK6/P4_5 A[21] AC B Bus O Low External bus
CS3/A20/N_CTS6/N_RTS6/
88 A[20] AC B Bus O Low External bus
N_SS6/P4_4
A19/TXD3/SDA3/SRXD3/
89 OUTC2_0/ISTXD2/IEOUT/ A[19] AC B Bus O Low External bus
P4_3
90 P11_6 ZTX_AUSEL1 AC O L Main O Low Sound switching 1 to ZONE TX
A18/RXD3/SCL3/STXD3/
91 A[18] AC B Bus O Low External bus
ISRXD2/IEIN/P4_2
92 P11_5 DFF_FROM_N_RST AC O L act O Low Reset of DFF
93 A17/CLK3/P4_1 A[17] AC B Bus O Low External bus
A16/N_CTS3/N_RTS3/N_
94 A[16] AC B Bus O Low External bus
SS3/P4_0
95 P16_7/TXD10 EX_MOSI AC O Data O Low FL / EEPROM / Expansion IO transmission data
96 P16_6/RXD10 EEP_MISO AC I Data O Low EEPROM reception data
97 P16_5/CLK10 EX_SCK AC O Clock O Low FL / EEPROM / Expansion IO communication clock
98 P16_4/N_CTS10/N_RTS10 NCPU_AMUTE NCPU_PON I H act O Low Mute signal from BridgeCO
A15/[A15/D15]/TA4IN/U/
99 A[15] AC B Bus O Low External bus
P3_7
A14/[A14/D14]/TA4OUT/U/
100 A[14] AC B Bus O Low External bus
P3_6
A13/[A13/D13]/TA2IN/W/
101 A[13] AC B Bus O Low External bus
P3_5
A12/[A12/D12]/TA2OUT/W/
102 A[12] AC B Bus O Low External bus
P3_4
103 P16_3/TXD9 NCPU_SPI_MOSI NCPU_PON O Data O Low Data (Master out slave in)
104 P16_2/RXD9 NCPU_SPI_MISO NCPU_PON I Data O Low Data (Master in slave out)
105 P16_1/CLK9 NCPU_SPI_SCK NCPU_PON O Clock O Low Clock (Master out slave in)
106 P16_0/N_CTS9/N_RTS9 NCPU_N_RST NCPU_PON O L act O Low Network microprocessor reset
A11/[A11/D11]/TA1IN/V/
107 A[11] AC B Bus O Low External bus
P3_3
A10/[A10/D10]/TA1OUT/V/
108 A[10] AC B Bus O Low External bus
P3_2
A9/[A9/D9]/TA3OUT/UD0B/
109 A[9] AC B Bus O Low External bus
UD1B/P3_1
99
 RX-A3020/RX-V3073

Related Power Supply

Pin
Port Name Function Name ON OFF Detail of Function
No.
I/O Logic I/O Logic
110 D20/P12_4 AD_SEL_A +3.3S_PON O O Low AD select A
D19/N_CTS6/N_RTS6/N_
111 AD_SEL_B +3.3S_PON O O Low AD select B
SS6/P12_3
D18/RXD6/SCL6/STXD6/
112 AD_SEL_C +3.3S_PON O O Low AD select C
P12_2
113 D17/CLK6/P12_1 FPGA_SCK HDMI_PON O Clock O Low FPGA clock (at Boot)
D16/TXD6/SDA6/SRXD6/
114 FPGA_MOSI HDMI_PON O Data O Low FPGA transmission data (at Boot)
P12_0
115 VCC VCC ---
A8/[A8/D8]/TA0OUT/UD0A/
116 A[8] AC B Bus O Low External bus
UD1A/P3_0
117 VSS VSS ---
A7/[A7/D7]/AN2_7/P2_7/
118 A[7] AC B Bus O Low External bus
TXD10
A6/[A6/D6]/AN2_6/P2_6/
119 A[6] AC B Bus O Low External bus
RXD10
A5/[A5/D5]/AN2_5/P2_5/
120 A[5] AC B Bus O Low External bus
CLK10
A4/[A4/D4]/AN2_4/P2_4/N_
121 A[4] AC B Bus O Low External bus
CTS10/N_RTS10
A3/[A3/D3]/AN2_3/P2_3/
122 A[3] AC B Bus O Low External bus
TXD9
A2/[A2/D2]/AN2_2/P2_2/
123 A[2] AC B Bus O Low External bus
RXD9
A1/[A1/D1]/BC2/[BC2/D1]/
124 A[1] AC B Bus O Low External bus
AN2_1/P2_1/CLK9
A0/[A0/D0]/BC0/[BC0/D0]/
RX-A3020/RX-V3073

125 AN2_0/P2_0/N_CTS9/N_ A[0] AC B Bus O Low External bus

RTS9
D15/N_INT5/IIO0_7/IIO1_7/
126 D[15] AC B Bus I --- External bus
P1_7
D14/N_INT4/IIO0_6/IIO1_6/
127 D[14] AC B Bus I --- External bus
P1_6
D13/N_INT3/IIO0_5/IIO1_5/
128 D[13] AC B Bus I --- External bus
P1_5
129 D12/IIO0_4/IIO1_4/P1_4 D[12] AC B Bus I --- External bus
130 D11/IIO0_3/IIO1_3/P1_3 D[11] AC B Bus I --- External bus
131 D10/IIO0_2/IIO1_2/P1_2 D[10] AC B Bus I --- External bus
132 D9/IIO0_1/IIO1_1/P1_1 D[9] AC B Bus I --- External bus
133 IIO0_0/IIO1_0/D8/P1_0 D[8] AC B Bus I --- External bus
134 AN0_7/D7/P0_7 D[7] AC B Bus I --- External bus
135 AN0_6/D6/P0_6 D[6] AC B Bus I --- External bus
136 AN0_5/D5/P0_5 D[5] AC B Bus I --- External bus
137 AN0_4/D4/P0_4 D[4] AC B Bus I --- External bus
138 P19_1 FPGA_N_CFG HDMI_PON O L act O Low FPGA nCONF
139 WR3/BC3/P11_4 FPGA_N_STA HDMI_PON I L act I --- FPGA nSTATUS
140 P19_0 FPGA_CDONE HDMI_PON I H act I --- FPGA CONF DONE
IIO1_3/N_RTS8/N_CTS8/
141 DIAG_CHECK AC O H act O Low Diag inspection result output / OK=High, NG=Low
WR2/CS3/P11_3
142 IIO1_2/RXD8/CS2/P11_2 NDAC_N_MT DSP_PON O L act O Low Net ZONE DAC mute
143 IIO1_1/CLK8/CS1/P11_1 MT_N_Z3 +3.3S_PON O L act O Low Mute ZONE 3/Rear Presence (Preout)
144 IIO1_0/TXD8/CS0/P11_0 NCPU_SPI_N_CS NCPU_PON O L act O Low Network microprocessor SPI chip select
145 P18_7 MT_N_F_MI +3.3S_PON O L act O Low Mute Front (Main amplifier input)
146 P18_6 MT_N_Z2 +3.3S_PON O L act O Low Mute ZONE 2/Front Presence (Preout)
147 P18_5 MT_N_SB_PO +3.3S_PON O L act O Low Mute SB (Preout)
148 P18_4 MT_N_MZ +3.3S_PON O L act O Low Mute Main ZONE (Preout/Main amplifier input)
149 P18_3 MT_N_EX1_MI +3.3S_PON O L act O Low Mute SP1 (Main amplifier input)
150 P18_2 MT_N_SB_MI +3.3S_PON O L act O Low Mute Surround Back (Main amplifier input)
151 AN0_3/D3/P0_3 D[3] AC B Bus I --- External bus
152 AN0_2/D2/P0_2 D[2] AC B Bus I --- External bus
153 AN0_1/D1/P0_1 D[1] AC B Bus I --- External bus
154 AN0_0/D0/P0_0 D[0] AC B Bus I --- External bus
IIO0_7/N_RTS6/N_CTS6/
155 SVID_DET VID_PON I H act I --- S-video detect
N_SS6/AN15_7/P15_7
IIO0_6/CLK6/AN15_6/
156 HP_N_DET DSP_PON I L act O Low Headphone detection
P15_6
IIO0_5/RXD6/SCL6/STXD6/
157 EX1_N_CS AC O L act O Low Expansion IO 1 chip select
AN15_5/P15_5
IIO0_4/TXD6/SDA6/
158 EX1_N_RST AC O L act O Low Expansion IO 1 reset
SRXD6/AN15_4/P15_4
IIO0_3/N_RTS7/N_CTS7/
159 DSP1_N_INT DSP_PON I L act O Low Interrupt from DSP1 (for DAU_N_INT distinction)
AN15_3/P15_3
IIO0_2/RXD7/AN15_2/
160 DIR1_N_INT DSP_PON I L act O Low Interrupt from DIR1 (for DAU_N_INT distinction)
P15_2
IIO0_1/CLK7/AN15_1/
161 IR_OUT AC O Data O Low Remote control cord output
P15_1
162 VSS VSS ---

100
 RX-A3020/RX-V3073

Related Power Supply

Pin
Port Name Function Name ON OFF Detail of Function
No.
I/O Logic I/O Logic
IIO0_0/TXD7/AN15_0/
163 HRX1_N_MT HDMI_PON I L act O Low Mute from HDMI RX1 (for HAU_N_INT distinction)
P15_0
164 VCC VCC ---
165 KI3/AN_7/P10_7 +3.3S_PON +3.3S_PON O H act O Low +3.3S power supply
166 KI2/AN_6/P10_6 AD2_COM +3.3S_PON I A/D O Low AD selector 2 COM input
167 KI1/AN_5/P10_5 AD1_COM +3.3S_PON I A/D O Low AD selector 1 COM input
168 KI0/AN_4/P10_4 HRX2_N_MT HDMI_PON I L act O Low Mute from HDMI RX2 (for HAU_N_INT distinction)
169 AN_3/P10_3 KY_AD3 AC I A/D O Low Key 3
170 AN_2/P10_2 KY_AD2 AC I A/D O Low Key 2
171 AN_1/P10_1 KY_AD1 AC I A/D O Low Key 1
172 AVSS AVSS ---
HDR_N_RST PRY O L act O Low HD Radio reset (U model)
173 AN_0/P10_0
TUN_N_RST PRY O L act O Low Tuner reset (C, R, T, K, A, B, G, F, L, S, J models)
174 VREF VREF ---
175 AVCC AVCC ---
STXD4/SCL4/RXD4/ HDR_MISO PRY I Data O Low HD Radio reception data (U model)
176
ADTRG/P9_7 TUN_SCL PRY O Data O Low Tuner I2C clock (C, R, T, K, A, B, G, F, L, S, J models)

Key detection for A/D port

Key input (A/D) pull-up resistance 10 k-ohms

0Ω + 0.82 kΩ + 0.82 kΩ + 1.0 kΩ + 1.5 kΩ + 1.5 kΩ + 1.8 kΩ + 2.7 kΩ

Detected voltage value 0– 0.125 – 0.358 – 0.577 – 0.828 – 1.078 – 1.299 – 1.535 –
at 171 pin 0.125 V 0.358 V 0.577 V 0.828 V 1.078 V 1.299 V 1.535 V 1.777 V

RX-A3020/RX-V3073
A/D value
0–9 10 – 27 28 – 44 45 – 63 64 – 83 84 – 100 101 – 118 119 – 137
(3.3 V=255)

SCENE SCENE SCENE SCENE ZONE 2 ZONE 3 ZONE 4 MAIN ZONE

KEY1
4 3 2 1 ON/OFF ON/OFF ON/OFF

0Ω + 0.82 kΩ + 0.82 kΩ + 1.0 kΩ + 1.5 kΩ + 1.5 kΩ + 1.8 kΩ + 2.7 kΩ + 3.3 kΩ + 4.7 kΩ + 6.8 kΩ + 12.0 kΩ + 22.0 kΩ
Detected voltage value 0– 0.125 – 0.358 – 0.577 – 0.828 – 1.078 – 1.299 – 1.535 – 1.777 – 2.010 – 2.241 – 2.476 – 2.709 –
at 170 pin 0.125 V 0.358 V 0.577 V 0.828 V 1.078 V 1.299 V 1.535 V 1.777 V 2.010 V 2.241 V 2.476 V 2.709 V 2.940 V

A/D value
0–9 10 – 27 28 – 44 45 – 63 64-83 84 – 100 101 – 118 119 – 137 138 – 155 156 – 173 174 – 191 192 – 209 210 – 227
(3.3 V=255)

TONE/ PROGRAM PROGRAM

KEY2 STRAIGHT OPTION ON SCREEN ENTER DISPLAY RETURN
BALANCE

0Ω + 0.82 kΩ + 0.82 kΩ + 1.0 kΩ + 1.5 kΩ + 1.5 kΩ + 1.8 kΩ + 2.7 kΩ + 3.3 kΩ + 4.7 kΩ

Detected voltage value 0– 0.125 – 0.358 – 0.577 – 0.828 – 1.078 – 1.299 – 1.535 – 1.777 – 2.010 –
at 169 pin 0.125 V 0.358 V 0.577 V 0.828 V 1.078 V 1.299 V 1.535 V 1.777 V 2.010 V 2.241 V

A/D value
0–9 10 – 27 28 – 44 45 – 63 64 – 83 84 – 100 101 – 118 119 – 137 138 – 155 156 – 173
(3.3 V=255)

PRESET PRESET ZONE TUNING/CH TUNING/CH PURE

KEY3 MEMORY INFO FM AM
CONTROL DIRECT

Destination detection for AD port

Pull-up resistance 10 k-ohms

A/D value
0 − 12 13 − 39 40 − 67 68 − 92 93 − 115 116 − 140 141 − 169 199 − 221 222 − 244
(3.3 V=255)
Destination J U C R, S T K A B, G, F L

101
 RX-A3020/RX-V3073

• Microprocessor extended port

IC70, 71: TC74VHC273FT (EL,K) (DIGITAL P.C.B.)
Octal D-type flip-flop with clear

CLR 1 20 VCC

Q1 2 19 Q8 D1 D2 D3 D4 D5 D6 D7 D8
1 3 4 7 8 13 14 17 18
D1 3 18 D8 CLR
D R D R D R D R D R D R D R D R
D2 4 17 D7

Q2 5 16 Q7

Q3 6 15 Q6 CK Q CK Q CK Q CK Q CK Q CK Q CK Q CK Q
11
CK
D3 7 14 D6

D4 8 13 D5
2 5 6 9 12 15 16 19
Q4 9 12 Q5
Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8
GND 10 11 CK

Inputs Output
Function
CLR D CK Q
RX-A3020/RX-V3073

L X X L Clear
H L L −
H H H −

H X Qn No Change

IC70
R32C Related Power Supply
Pin
external Function Name ON OFF Detail of Function
No.
bus data I/O Logic I/O Logic
2 D[8] HDMI_PON HDMI_PON O H act O Low HDMI power supply (Necessary for DSP, A-VIDEO drive)
5 D[9] HRX1_N_RST HDMI_PON O L act O Low HDMI receiver reset
6 D[10] HTX1_N_RST HDMI_PON O L act O Low HDMI transmitter reset
9 D[11] HTX2_N_RST HDMI_PON O L act O Low HDMI transmitter 2 reset
12 D[12] CEC_EN HDMI_PON O H act O Low CEC function ON/OFF of HDMI transmitter 2
15 D[13] HTX_AUSEL HDMI_PON O H HRX O Low HDMI transmitter sound select
16 D[14] HAU_N_OE HDMI_PON O L act O Low HDMI to DIR sound output enable
19 D[15] ZTX_AUSEL2 AC O Low O Low Switching of the HDMI sound and except HDMI

IC71
R32C Related Power Supply
Pin
external Function Name ON OFF Detail of Function
No.
bus data I/O Logic I/O Logic
2 D[0] HSW_N_RST HDMI_PON O L act O Low HDMI switcher reset (L period: More than 5ms)
5 D[1] VDEC_N_RST VID_PON O L act O Low Video decoder reset
6 D[2] WIFI_PON WIFI_PON O H act O Low WiFi adaptor power supply control (spare)
9 D[3] HRX_VSEL HDMI_PON O L DEC O Low Video decoder to scaler route enable
12 D[4] F_HEQ_CE HDMI_PON O H act O Low Front HDMI + 3.3HF power supply:
Interlocking movement with HDMI_PON
15 D[5] VID_PON VID_PON O H act O Low Video power supply
16 D[6] +3.3D_PON +3.3D_PON O H act O Low OR of HDMI_PON, DSP_PON, NET_USB_PON
19 D[7] PRY PRY O H act O Low Power relay

102
 RX-A3020/RX-V3073

IC72, 73: TC74VHC273FT (EL,K) (DIGITAL P.C.B.)

Octal D-type flip-flop with clear

CLR 1 20 VCC

Q1 2 19 Q8 D1 D2 D3 D4 D5 D6 D7 D8
1 3 4 7 8 13 14 17 18
D1 3 18 D8 CLR
D R D R D R D R D R D R D R D R
D2 4 17 D7

Q2 5 16 Q7

Q3 6 15 Q6 CK Q CK Q CK Q CK Q CK Q CK Q CK Q CK Q
11
CK
D3 7 14 D6

D4 8 13 D5
2 5 6 9 12 15 16 19
Q4 9 12 Q5
Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8
GND 10 11 CK

Inputs Output
Function
CLR D CK Q

RX-A3020/RX-V3073
L X X L Clear
H L L −
H H H −

H X Qn No Change

IC72
R32C Related Power Supply
Pin
external Function Name ON OFF Detail of Function
No.
bus data I/O Logic I/O Logic
2 D[8] MONO_Z2 PRY O H act O Low ZONE 2 stereo/mono output switch
5 D[9] MONO_Z3 PRY O H act O Low ZONE 3 stereo/mono output switch
6 D[10] EX2_N_RST AC O L act O Low Reset of expansion IO2
9 D[11] EX2_N_CS AC O H act O Low Chip select of expansion IO2
12 D[12] DAC_N_CS_SW DSP_PON O L act O Low DAC chip select SW
15 D[13] DAC_N_CS_FP DSP_PON O L act O Low DAC chip select Front Presence
16 D[14] DAC_N_RST_SB_FP DSP_PON O L act O Low DAC reset Surround Back/Front Presence
19 D[15] DAC_MUTE_RP DSP_PON O H act O Low DAC mute Rear Presence

IC73
R32C Related Power Supply
Pin
external Function Name ON OFF Detail of Function
No.
bus data I/O Logic I/O Logic
2 D[0] SCR_N_RST HDMI_PON O L act O Low Reset of scaler (VHD1900)
5 D[1] Spare AC O Low O Low Spare (for power supply control of VIDEO P.C.B.)
(VID_PON2)
6 D[2] FLP_PON FLD_PON O H act O Low FL driver VH and filament power supply control
9 D[3] DAC_N_RST DSP_PON O L act O Low DAC reset C/SR/SW
12 D[4] DAC_N_RST_F DSP_PON O L act O Low DAC reset Front
15 D[5] VID_PON VID_PON O H act O Low Video power control
16 D[6] DSP2_N_RST DSP_PON O L act O Low Reset of DSP2
19 D[7] VOL3_CS PRY/ O L act O Low VOL3 (NJU7313AM) chip select
DSP_PON
103
 RX-A3020/RX-V3073

IC76, 77: SN74LV4051APWR (DIGITAL P.C.B.)

8-channel analog multiplexers/demultiplexers

Y4 1 16 VCC
Y6 2 15 Y2
COM 3 14 3
Y1 COM
Y7 4 13 Y0
Y5 5 12 13
Y3 Y0
INH 6 11 A
GND 7 10 B 14
11 Y1
GND 8 9 C A

15
Y2

12
10 Y3
B
INPUTS ON
1
INH C B A CHANNEL Y4
L L L L Y0
5
L L L H Y1 9 Y5
C
L L H L Y2
L L H H Y3 2
Y6
L H L L Y4
RX-A3020/RX-V3073

L H L H Y5 4
6 Y7
L H H L Y6 INH

L H H H Y7
H X X X None

IC76 (AD2)
Related Power Supply
Pin
Port Name Function Name ON OFF Detail of Function
No.
I/O Logic I/O Logic
AD selector 2 (AD2_COM signal is input into AN_6 of R32C)
1 Y4 THM2 +3.3S_PON I A/D I --- Temperature detection 2
2 Y6 THM3 +3.3S_PON I A/D I --- Temperature detection 3
4 Y7 THM4 +3.3S_PON I A/D I --- Temperature detection 4
5 Y5 DEST +3.3S_PON I A/D I --- Destination distinction
12 Y3 MODEL +3.3S_PON I A/D I --- Model distinction
13 Y0 Space +3.3S_PON I A/D I --- –
14 Y1 USB_VBUS_PRT +3.3S_PON I A/D I --- Front USB overcurrent detection
15 Y2 Space +3.3S_PON I A/D I --- –

IC77 (AD1)
Related Power Supply
Pin
Port Name Function Name ON OFF Detail of Function
No.
I/O Logic I/O Logic
AD selector 1 (AD1_COM signal is input into AN_5 of R32C)
1 Y4 PS2_PRT +3.3S_PON I A/D I --- Power supply protection 2
2 Y6 PS1_PRT +3.3S_PON I A/D I --- Power supply protection 1
4 Y7 AMP_OLV PRY I A/D I --- Amplifier output level detection
5 Y5 DC_PRT PRY I A/D I --- DC protection
12 Y3 THM1 +3.3S_PON I A/D I --- Temperature detection 1
13 Y0 PS3_PRT AC I A/D I --- Power supply protection 3
14 Y1 L3_DET VID_PON I A/D I --- D terminal L3 detection
15 Y2 MODE +3.3S_PON I A/D I --- Special mode distinction
104
 RX-A3020/RX-V3073

IC306: R5F213G1DN400SP#W4 (VIDEO P.C.B.) IC182 (Expansion IO2)

IC182: R5F213G1DN400SP#W4 (AMPPOWER P.C.B.) Related Power Supply
Pin
Single chip 16 bit microprocessor Port Name Function Name ON OFF Detail of Function
No.
I/O Logic I/O Logic
8 P17 – – – – O Low No used
4 8 4 3 1 9 P16 – – – – O Low No used
10 P15 – – – – O Low No used
I/O ports Port P0 Port P1 Port P3 Port P4
11 P14 – – – – O Low No used
12 P13 – – – – O Low No used
Peripheral functions 13 P12 – – – – O Low No used
UART or System clock 14 P11 – – – – O Low No used
clock synchronous serial I/O
Timers (8 bits x 2)
generation circuit
15 P10 PA_B_RY1 PRY O H:B=Low O Low Power amplifier B power supply control 1
XIN-XOUT
High-speed on-chip oscillator 17 P07 – PRY – – O Low No used
Timer RA (8 bits x 1) Low-speed on-chip oscillator
Timer RB (8 bits x 1) XCIN-XCOUT
18 P06 SPRY_F_RP_CTRL PRY O H act O Low SP relay Front -> SP2
Timer RC (16 bits x 1)
Timer RE (8 bits x 1) 19 P05 SPRY_ZRP_CTRL PRY O H act O Low SP relay Surround Back -> SP2
Low-speed on-chip oscillator
for watchdog timer
20 P04 SPRY_ZFP_CTRL PRY O H act O Low SP relay Front Presence -> SP1
21 P03 SPRY_SB_CTRL PRY O H act O Low SP relay Surround Back
Voltage detection circuit FILT 1 24 VDD 22 P02 SPRY_SR_CTRL PRY O H act O Low SP relay Surround
Watchdog timer
(14 bits) AVSS 2 23 DVSS 23 P01 SPRY_C_CTRL PRY O H act O Low SP relay Center
Comparator B
PDN 3 22 TVDD 24 P00 SPRY_F_CTRL PRY O H act O Low SP relay Front
A/D converter
(10 bits x 8 channels) SMUTE 4 21 MCLK

DEM0 5 20 OLRCK
R8C microprocessor core Memory DEM1 6 19 OBICK

R0H R0L SB ROM(1) ILRCK 7 18 SDTO

R1H R1L USP
R2 IBICK 8 17 ODIF1
R3 ISP
RAM(2)
IC61, 62: Sii9136CTU-3 (DIGITAL P.C.B.)
INTB SDTI 9 16 ODIF0
A0
A1
PC IDIF0 10 15 CMODE2
HDMI transmitter
FB FLG
IDIF1 11 14 CMODE1
Multiplier Related Power Supply
IDIF2 12 13 CMODE0
Pin
Port Name Function Name ON OFF Detail of Function
NOTES: 1. ROM size varies with MCU type.
2. RAM size varies with MCU type.
No.
I/O Logic I/O Logic
26 GPIO0 NC HDMI_PON O L --- --- Unconnected: Output LOW setting
39 GPIO2 NC HDMI_PON O L --- --- Unconnected: Output LOW setting
IC306 (Expansion IO1) 49 GPIO3 5HT*_PON HDMI_PON O H act --- --- HDMI out * 5VPWR output control
Related Power Supply Low: 5V Power OFF / High: 5V power ON
Pin
Port Name Function Name ON OFF Detail of Function
No. 77 GPIO1 NC HDMI_PON O L --- --- Unconnected: Output LOW setting
I/O Logic I/O Logic
8 P17 – AC O Low O Low No used
9 P16 – AC O Low O Low No used
10 P15 – AC O Low O Low No used
11 P14 DC_TRG2 PRY O H act O Low Control out 2
12 P13 – AC O Low O Low No used
13 P12 DC_TRG1 PRY O H act O Low Control out 1
14 P11 VO_SEL2 VID_PON O Low O Low MON output select of Y/C
15 P10 VO_SEL1 VID_PON O Low O Low MON output select of Y/C
17 P07 – AC O Low O Low No used
18 P06 VID_SEL1 VID_PON O O Low Input select of Y/C
19 P05 VID_SEL2 VID_PON O O Low Input select of Y/C
20 P04 VID_SEL3 VID_PON O O Low Input select of Y/C
21 P03 V_N_FMUTE VID_PON O O Low Video full mute
22 P02 VZ_SEL3 VID_PON O O Low ZONE 2 select of Y/C
23 P01 VZ_SEL2 VID_PON O O Low ZONE 2 select of Y/C
24 P00 VZ_SEL1 VID_PON O O Low ZONE 2 select of Y/C

105
 A B C D E F G H I J
RX-A3020/RX-V3073

1 ■ BLOCK DIAGRAMS
AUDIO Section Block Diagram

r
4FF
QBHF

→
r
4FF
QBHF

→ FUNCTION (2)
OPERATION SCHEMATIC DIAGRAM
SCHEMATIC DIAGRAM HDMI Tx

DANET AV 1 (Coax) 0dBFs=2.8Vrms

AV 2 (Coax) IC900 IC920 LPF DAF
AV 3 (Opt) DIR/ADC LPF DASr
DSP2 IC812-815
2 IC951
IC937 AV 4 (Opt)
AV-OUT/Zone 4 (Opt)
IC903
IC938
PCM9211
IC911
D80YK113 DAC
LPF DASB(/FP/RP)
USB DAC Zone 2 Zone 2
DAC
PCM5101PWR AUDIO 1 (Opt) DSP1 CPTP400 LPF
DIR/ HDMI
NETWORK AUDIO 2 (Coax) ADC TRANSMITTER D80YK113 LPF DASW1/2
microprocessor PCM1789
DIGITAL V-AUX (Opt)
PCM9211
CPTP400
PWR
LPF DAFP
LAN IC937 IC871 LPF DARP r
4FF
QBHF

→
r
4FF
QBHF
m
→ HDMI Rx DAC ADC FUNCTION (1)
PCM5101 r
4FF
QBHF

→ SCHEMATIC DIAGRAM
SCHEMATIC DIAGRAM AK5386VT
DAC
SCHEMATIC DIAGRAM
0dBFs=2.8Vrms
Max:2.8Vrms/typ:0.2Vrms DAZ2
ADC(OUT) -95dB∼0dB 0dB∼42dB
8chIN(F) IN1 SUB1(OUT) Zone 2 Multi1 Tone Front Zone 2/FP typ:1Vrms(Vol:+16.5dB) ZONE OUT
SUB2(OUT) Multi2 Control Mute ZONE 2/FrontPres.
Bypass Bypass 50k-ohms MT_Z2
AUDIO 4 IN2 Z2 to SB/EX2 typ:1Vrms(Vol:+16.5dB)
Mute ZONE 3/RearPres.
-95dB∼0dB 0dB∼42dB IC762 MT_Z3
NJM4565M
3 AUDIO 3 IN3 INA/REC1 AV-OUT DASW Multi1 C/SW SW1/2 typ:1Vrms(Vol:+16.5dB) PRE OUT
INB/REC2 8chIN(SW) Multi2 Mute SUBWOOFER 1/2
REC3 IC713 50k-ohms MT_MZ
AUDIO 2 IN4 IN10/REC4
IN11/REC5
4.5dB OPERATION
IC763
-95dB∼0dB 0dB∼42dB BA15218F r
4FF
QBHF

→
AUDIO 1 IN5 DAF Multi1 Surround FP/HP
Multi2 Mute PHONES
SCHEMATIC DIAGRAM
50k-ohms MT_MZ 100 ohms typ:0.6Vrms@8 ohms(Vol:+16.5dB)
AV 4 IN6 17.78dB

-95dB∼0dB 0dB∼42dB
AV 3 IN7 DAF Multi1 Surr.Back Front typ:1Vrms(Vol:+16.5dB)
Multi2 Mute FRONT PRE OUT
50k-ohms MT_MZ
AV 2 IN8 BiAmp to SB/EX2
IC743
DAFP SCIN IC741 NJM7313AM
4 AV 1 IN9 SBCIN R2A15220 J7414/7418 SW1 Mute ZONE 2/
#1(2/2) MT_EX1_MI SPRY_ZFP F. PRESENCE/
SW2
IC701 29.03dB BI-AMP
SW3
PHONO INB/REC2 SW4
PhonoEQ.
SW5
NJM2068MD Mute
SW6 FRONT L/R
IN10/REC4 MT_F_MI SPRY_F
SW7
29.03dB
SW8
IN11/REC5

V-AUX IN12 Mute CENTER

MT_MZ SPRY_C SPEAKERS
IC741 29.03dB
ext.IN IN13 R2A15220 SPRY_F_RP
#1(1/2) 11chAMP
Mute ZONE 2/ZONE 3/
5 IN14 MT_EX2_MI SPRY_ZRP
F. PRESENCE/BI-AMP
29.03dB SPRY_ZRP

OPERATION J7408/7409
Mute SURROUND BACK L/R
r
4FF
QBHF

→ MT_SB_MI SPRY_SB
SCHEMATIC DIAGRAM 29.03dB
Zone 2
Zone 3
Main

Mute SURROUND L/R

MT_MZ SPRY_SR
ext.Z2 ADC(OUT) -95dB∼0dB 0dB∼42dB 29.03dB typ:28.3Vrms(Vol:+16.5dB)
IN3 SUB1(OUT) Zone 2 Mono Zone 3 Multi1 Tone Front Zone 3/RP
SUB2(OUT) Zone 3 Mono Multi2 Control
ext.Z3 Bypass Bypass r
4FF
QBHF


→
50k-ohms AMP
IN4 Z3/RP to SB/EX2 SCHEMATIC DIAGRAM
-95dB∼0dB 0dB∼42dB
6 DAF IN7 INA/REC1 DAC/- Multi1 C/SW C/- typ:1Vrms(Vol:+16.5dB)
INB/REC2 8chIN(C) Multi2 Mute CENTER
REC3 50k-ohms MT_MZ
YPAO MIC IN8 IN10/REC4
IN11/REC5
-95dB∼0dB 0dB∼42dB
DANET IN9 DASr Multi1 Surround Sr typ:1Vrms(Vol:+16.5dB)
8chIN(SR) Multi2 Mute SURROUND PRE OUT
50k-ohms MT_MZ
DAZ3 INB/REC2
IC761
-95dB∼0dB 0dB∼42dB NJM4565M
AM/FM Tuner IN10/REC4 DASB(/FP/RP) Multi1 Surr.Back SB(/FP/RP) typ:1Vrms(Vol:+16.5dB)
VIDEO 8chIN(SB) Multi2 Mute SURROUND BACK
50k-ohms MT_SB_PO
r
4FF
QBHF


→ 0dB
DAFP IN12
SCHEMATIC DIAGRAM
IC742 SCIN IC742
7 DARP IN13 R2A15220 SBCIN R2A15220
#2(1/2) #2(2/2)

106
 A B C D E F G H I J
RX-A3020/RX-V3073

DIGITAL P.C.B. Section Block Diagram

HDMI (Front)
r
4FF
QBHF

→ r
4FF
QBHF

→
DIGITAL (2) RS232C DIGITAL (3)
SCHEMATIC DIAGRAM SCHEMATIC DIAGRAM
IC30
HDMI Equalizer USB
AD8192ACPZ
HDMI IN 232C
HDMI OUT
2 TRS3221
IC35
NETWORK
IN7 IN6 IN5 IN4 IN3 IN2 IN1 OUT2 OUT1

CEC
RS232C

HEQ_SCL/SDA
IC62 IC61 TX/RX
B IC2 C B IC1 C
HDMI HDMI
A HDMI D A HDMI D
Transmitter Transmitter
HDMI_SCL/SDA Switcher HDMI_SCL/SDA Switcher HDMI_SCL/SDA
Sil9136CTU-3
HDMI_SCL/SDA
Sil9136CTU-3
HSW2_27MHz ADV7630KSVZ HSW1_27MHz ADV7630KSVZ
TXB TXA TXB TXA
IC955
IC66 Ethernet PHY USB_DP/DM

3 ARC Buffer LAN8700C-AEZG-TR

TC74VHCU04FT
Main HDMI Audio
RT_SD0-3 RT_SD1-3

RXB RXA RXB RXA RMII 50MHz

HDMI_SCL/SDA
HDMI_SCL/SDA
Zone HDMI Audio RT_SPDIF
IC3 IC4 RTZ_SD0-3

SZ_SPDIF
SZ_SD0-3
XL951
HDMI Receiver HDMI Receiver RTZ_SPDIF 24MHz
ADV7619KSVZ ADV7619KSVZ I2C_SCL/SDA
IC53
115 116 SDRAM
115 116 IC956
XL1 XL2 SDRAM_27MHz 128Mbit Apple IC951
28.63636MHz 28.63636MHz NT5SV8M16HS-6K
XL51
16bit
Authentication NETWORK
27MHz
HSW1_27MHz MFI341S2162 microprocessor
HSW2_27MHz 48bit 36bit
SCLR_27MHz Bridge Co
FPGA_27MHz
36bit
SDRAM_27MHz IC50 DM860A
48bit
FPGA
4 EP4CE15F23C6N
16bit 16bit
Main/Zone HDMI
HDMI_SCL/SDA
IC41 20bit Audio Repeat IC952 IC953
IC23-25
SDRAM NOR Flash

NCPU SPI
Buffer IC901,902

Net/USB I2S
TC74LCX245FT SCLR_27MHz
Scaler FPGA_27MHz 256Mbit 256Mbit
ADCVBS 35 VHD1900 M12L2561616A-5T MX29GL256FLT2I
AIN1 x2 DIR2_SD0
ADSY 36 IC21 20bit 8bit
AIN2
Analog Video IN ADSC 46
AIN3
HDMI Decoder 16bit
FPGA_N_CS
Zone Audio UP IC938
ADPb 47 AIN4
ADV7181CBSTZ FPGA SPI ZONE I2S ZONE_L / R Zone HDMI
ADPr 48 DAC Analog Audio
AIN5 DV_SCL/SDA
ADY 49 AIN6
IC75 16bit Main HDMI Z2_SPDIF
PCM5101PWR
RT_SD1-3 MAIN OUT
21 22 Flash ROM IC903
RT_SPDIF I2S SD0 DSP SPI
XL20 64Mbit
28.63636MHz DIR2
IC64 SPDIF from DIR1 IC937
FLASH_N_CS PCM9211PTR Net/USB I2S NET_L / R Zone 2
DAY DAC A AUP_SD0 SPDIF from RX2
DAC
DAPb IC20
RT_SD0 MPIO_C Analog Audio
DAC B IC71,71 16bit PCM5101PWR
DAPr
5 Analog Video OUT DACVBS
DAC C HDMI Encoder DFF1 IC65 AUP_SD0 MPO1
ADC

DAC D ADV7172KSTZ VHC272 x2 Buffer Main AudioUP

DASY DAC E DV_SCL/SDA
TC74LCX245FT RTZ_SD0-3 XL901
DASC DAC F DFF1_N_CS
24.576MHz
XMCKO
IC72,73 RTZ_SPDIF
16bit NCPU SPI
DFF2
VHC272 x2 HDMI_ARC
ZONE2_AD_L / R
RS232C (HDMI SPDIF) HDIG_DSD0A
DFF2_N_CS

MPIO_B HDMI RX1_SPDIF

EBIU SPI6 UART8 SPI9
UART1 RX1 I2S (HPSD0)
MPIO_C IC900
HDMI_ARC
DV_SCL/SDA UART2
AV1_D
HDMI_SCL/SDA I2C3 DIR1
HD Radio Tuner/ IC79 HPSD1~SD3 DSP SPI AV2_D
I2C4/UART4
AM/FM Tuner McASP1
DIR I2S PCM9211PTR AV3_D SPDIF Input
HEQ_SCL/SDA I2C5 Microprocessor McASP1
MAIN OUT
HDIG_DSD0A AV4_D
R32C/116A DSP I2S SD0-3
6 FL display SPI10
R5F6416MADFE
(HDMI DSD) IC911 McASP0
DSP SPI
IC76 SPI0 SPI1 DSP1 ADC AD_L / R
Analog Input
166
IC78 Analog Mux AN6 D80YK113CPTP400
16bit
EEPROM SN74LV4051APWR EMIFB DSP I2S SD0-7
RAM:96K Byte McASP1
512Kbit
R1EX25512ATA00A IC77 167 ROM:1M Byte SPI0 IC920
Analog Mux AN5
SN74LV4051APWR AN4
Clock:50MHz 16bit DSP SPI SPI1 DSP2 Main Zone I2S
169
KY_AD3 AN3 D80YK113CPTP400 MAIN Zone DAC
170 IC913 IC910 16bit DSP SPI
Front Panel Key KY_AD2 AN2 143 145 EMIFB
KY_AD1
171
AN1
SDRAM Serial Flash McASP0
DSP I2S SD0-6
64Mbit 8Mbit XL910
20MHz SPI0
22 24 M12L64164A-5TG2 W25Q80BVSSG
XL70
8MHz CERALOCK IC921
IC922
SDRAM Serial Flash 143 145
64Mbit 8Mbit
7 r
4FF
QBHF
m
→
M12L64164A-5TG2 W25Q80BVSSG XL911
20MHz
DIGITAL (1)
SCHEMATIC DIAGRAM

107
 A B C D E F G H I J
RX-A3020/RX-V3073

VIDEO Section Block Diagram

P.C.B. AMP P.C.B. FUNCTION
AV1-AV4_CVBS
,AUX_CVBS,DK1_CVBS
IC*** 0.1046U$ ±12RY ±12V, +5A
,DK2_CVBS,MUTE CVBS IN_CVBS AG1/2_SENS
INPUT Selector C4081
PS1/PS2_PRT
TC74HC4051AF
±3.3V AD_M_CVBS AG1/2_RETURN
VID_/VZ_ SEL1(A) SEL2(B) SEL3(C) HDR_PON
0dB IC331
AUX_C MUTE L L L +3.3HDR
VID_SEL1/VID_SEL2/VID_SEL3
AUX_Luma AV1 H L L ±3.3V +3.3HDR NJM2388F33 +7V +7V
OPERATION AUX_CVBS AV2 L H L VGND
V-AUX IC*** 0.1046U$
r
4FF
QBHF

→
2 AV3 H H L CVBS ZONE_CVBS PS1_PRT -7V AMPPOWER (1)
Power supply
SCHEMATIC DIAGRAM AV4 L L H ZONE Selector
TC74HC4051AF
±3.3V AD_Z_CVBS MODE +18V
V-AUX H L H 6dB 232C_Tx +7V IC332 TRG_GND
+3.3V

FHP3350IM14X1
DK

to FUNCTION (1)
L H H ±3.3V IOXV_MOSI VID_PON +3.3V

IC*** 0.379U$
VZ_SEL1/VZ_SEL2/VZ_SEL3 NJM2388F33
L3_DET - H H H IOXV_N_RST +5T
D4 VIDEO
(J model) IC301
Luma IN_Luma TUL/TUR/TUE
INPUT Selector

MODE
P1-4
AV1-AV4_Luma TC74HC4051AF ±3.3V
,AUX_Luma,DK1_Luma VID_SEL2 P0-1 Q3303-3306
-3.3V
IN1_Y ,DK2_Luma,MUTE×2 VID_SEL1 P0-2 -3.3V TUL/TUR/TUE
VID_SEL1/VID_SEL2/VID_SEL3 2 IOXV_MOSI KTA1046-Y-U/P
AV 1 IN1_Pb - P0-6 RXD0 -7V
15 6 IOXV_N_RST
IN1_Pr VO_SEL1 P0-7 RESET PS1_PRT +5T

AM/FM Tuner / HD Radio

IC302
C IN_C +3.3HDR
INPUT Selector 14
IN1_C TC74HC4051AF ±3.3V VO_SEL2 P1-0 TUN_SCL Power transformer
13
IN1_Luma DC_TRG1 P1-1 TUN_SDA
3
- P1-2 TUN_N_INT
VID_SEL1/VID_SEL2/VID_SEL3 11
IN1_CVBS DC_TRG2 P1-3 IC306 TUN_N_RST
9 I/O EXPANDER
IC303 IRB_N_RST P1-7 R5F213G1DNSP
Luma ZONE_Luma RDS_CLK
ZONE Selector 8 3 IOXV_CLK U3301
TC74HC4051AF ±3.3V AD_Z_Luma IR_N_PASS RDS_MISO DET_OUT
24 RDS
6dB VZ_SEL1 P3-4 RDS_RST LC72725KM-UY-TL
IN2_Y
VZ_SEL1/VZ_SEL2/VZ_SEL3
VZ_SEL2
23
22
4

6
IOXV_N_CS
IOXV_N_RST
RDS_RDY VIDEO (3)
IN2_Pb AV1_C-AV4_C VZ_SEL3 P3-7 P4-5
IN2_Pr ,AUX_C,DK_C, IC304
+Vp
C 21
AV 2 ,DK2_C,MUTE×2 ZONE_C V_N_FMUTE P4-6 IR_IN_1
ZONE Selector 20 IN
D3310
IN2_C TC74HC4051AF ±3.3V AD_Z_C VID_SEL3 P4-7 5 +3.3M
REMOTE 1
DC-DC Converter for FL
Infrared LED
IN2_Luma 6dB
SIR-505STA47 IR_OUT_1
U3301 OUT
REM_IN2 REM_IR
VZ_SEL1/VZ_SEL2/VZ_SEL3
IN2_CVBS SM3385VMH6
IR_IN_2
4 VIDEO INPUT D3310
IN
P.C.B. OPERATION (1)
OUT_Luma Infrared LED REMOTE 2
IN_Luma/C 12 IC308 13 VID_SDA Q3004 HDMI_SDA SIR-505STA47 IR_OUT_2 OUT
ZONE_Luma/C 15 Luma/C VID_SCL FET SW HDMI_SCL +5.5V, DGND, +44V, FGND,
OUTPUT Selector UPA672T-T1-A
DA_Luma/C 14 TC74HC4052AF 3 OUT_C FLAC, FLAC, PS2_PRT,
IN3_Y IR_OUT Q3310 Q3308 FL_PON
DTC114EKA 2N5401C-
IN3_Pb IC307 AT/P
VO_SEL1/VO_SEL2
IN3_Pr IN1-4_CVBS 87-89,91 IN_Luma 1 MAIN SVIDEO 8 SVID_M_DET Q3309
DETECTOR 2N5401C-
AV 3 AUX_CVBS AD_M_CVBS (0dB Buffer） TC74VHCU04FT 14 ±3.3V AT/P
9 IN / 5 OUT

0/6
IN3_C DK_CVBS 1k-ohms AV_CVBS (0dB Buffer）
Selector

0/6
IN3_Luma DA_CVBS 94 1k-ohms
82 MON_CVBS (6dB Driver） JK331
6dB Q3311-3318
OUT_Luma/OUT_C 95,96 75-ohms
81 MON_Luma (6dB Driver） IC307 +18V 12V/100mA TRIGGER OUT 1/2
6dB
IN3_CVBS DA_Luma/DA_C Zone SVIDEO Driver
83 MON_C (6dB Driver） AD_Z_Luma SVID_Z_DET L3_DET +12V MAX 100mA
75-ohms
6dB DETECTOR
75-ohms TC74VHCU04FT ±3.3V
DC_TRG1/DC_TRG2
5
6 IN / 4 OUT

0/6
70 AD_M_Y (6dB Buffer）
Selector

IN_C 15 1k-ohms
68 AD_M_C (6dB Buffer）
0/6
IN4_Y IN1-4_Y 18,19,21,22 1k-ohms
71 MON_Y (6dB Driver）
6dB
IN4_Pb DA_Y 16 75-ohms
69 AV_C (6dB Driver） AD_Z_Y
6dB
IN4_Pr 75-ohms AD_Z_Pb
AV 4 AD_Z_Pr
6 IN / 4 OUT

IN4_C 61 AD_M_Pb (6dB Buffer） AD_Z_Luma

0/6
Selector

IN4_Luma DK_CVBS 1k-ohms AD_Z_Pb (6dB Buffer） AD_Z_C

0/6
IN1-4_Pb Zone
32-35 1k-ohms
62 MON_Pb (6dB Driver） AD_Z_CVBS
6dB Video
IN4_CVBS DA_Pb 31 75-ohms AV_CVBS (6dB Driver） Decoder
6dB
75-ohms AD_M_Y
AV_C AD_M_Pb
6 IN / 4 OUT

AV_Luma 52 AD_M_Pr (6dB Buffer） AD_M_Pr

0/6
Selector

Drv
IN_Luma 44 1k-ohms
51 AV_Luma (6dB Buffer） AD_M_Luma
6 AVOUT C4081 0/6
AV_CVBS IN1-4_Pr 39-42 1k-ohms
53 MON_Pr (6dB Driver） AD_M_C
Drv 6dB IC21
C4081 DA_Pr 43 75-ohms
49 AD_M_Luma (6dB Driver） AD_M_CVBS Video
6dB
75-ohms Decoder

IC305
CVBS/COMPONENT SEL ±3.3V DA_Y
MONITOR OUT/ CVBS/Luma/C/CVBS Driver
MON_Y NJW1327FU1 DA_Pb
ZONE OUT IC50
MON_Pb DA_Pr
VID_SCL/VID_SDA/V_N_FMUTE FPGA/Video Processor
MON_Pr DA_Luma
MONITOR OUT/
DA_C
ZONE OUT
MON_C DA_CVBS
MON_Luma Video Zone
HDMI
Encoder HDMI

MON_CVBS

7
r
4FF
QBHF


→
VIDEO (1)
SCHEMATIC DIAGRAM
DIGITAL r
4FF
QBHF
m
→
SCHEMATIC DIAGRAM

108
 A B C D E F G H I J
RX-A3020/RX-V3073

Power Amplifier and Power Supply Sections Block Diagram

Power amplifier +LB/-LB
+B/-B
FL RY105
29dB +

+LB/-LB -
+B/-B FRONT
FR RY105
29dB + L/R

+LB/-LB -
+B/-B
C RY104
2 29dB +
CENTER
+LB/-LB -
+B/-B
SL RY107
29dB +

+LB/-LB - SURROUND
+B/-B
SR RY107 L/R
29dB +

-
RY101
+
SPEAKERS
RY102 - ZONE 2/ZONE 3/
3 RY101 R. PRESENCE
+
L/R VIDEO P.C.B.

+LB/-LB RY102 -
+B/-B
RY106 PRIMARY SECONDARY
SBL
29dB +

+LB/-LB - SURROUND BACK +5.5V DIGITAL P.C.B.

SBR
+B/-B
RY106 AC IN T2001
L/R Q2001 SUB-transformer
29dB +
Switching Transistor
+LB/-LB -
+B/-B
FPL RY108
29dB + IC203
IC201 Lower Voltage limit IC
4 +LB/-LB - ZONE 2/ZONE 3/ Switching control IC
+B/-B IC204
RY108 F. PRESENCE/ L6566BTR
FPR Over Voltage limit IC
29dB + BI-AMP
-
L/R

I_PRT

DC_PRT
POWER
AMP_OLV
r
4FF
QBHF

→
EX_SCK SCHEMATIC DIAGRAM
AMP EX_MOSI
R5F213G

POWER
5 r
4FF
QBHF


→ EX2_N_CS
SCHEMATIC DIAGRAM EX2_N_RS
+B RY180
+LB
D1808
Power AMP_Power
Transformer
C1822
AMP_LMT

-B
-LB C1823

PS1_PRT
+7 D1807

C1826
PS2_PRT
6
C1827
-7

Q1804
+5A D1810
+5A

C1828

+12V Q1805
D1809
+12V

AMPPOWER C1820

7 r
4FF
QBHF

→
-12V
Q1806 C1825
SCHEMATIC DIAGRAM -12V

109
 A B C D E F G H I J
RX-A3020/RX-V3073
Ref no. Location Ref no. Location Ref no. Location Ref no. Location Ref no. Location Ref no. Location
DIGITAL (2) IC72 D5 IC85 F5 IC910 G5 IC917 H6 IC934 H3 IC953 H3
(CB31)
■ PRINTED CIRCUIT BOARDS

F_HEQ_CE
1

+5VPower
IC73 D6 IC86 F6 IC911 G5 IC918 H4 IC935 I4 IC955 I3

FR_SDA
FR_SCL

SheildC
DataC+
Sheild0

Sheild1

Sheild2
Data0+

Data1+

Data2+
DataC-

Data0-

Data1-

Data2-
Sheild
IC75 E5 IC900 H4 IC913 G5 IC920 H5 IC936 C5 IC956 I3

+Vcc
+Vcc
HPD

CEC
SDA
SCL
IC76 F5 IC901 G3 IC914 H4 IC921 H5 IC937 I4 Q13 D4

-
IC77 F5 IC902 G3 IC915 F5 IC922 H6 IC938 I4 Q14 D4
DIGITAL (1) (Side A) IC79 E5 IC903 I5 IC916 H6 IC930 I2 IC939 C5 Q17 D4
IC951 I3 Q18 D4
No replacement part available.
HDMI HDMI OUT Q19 B2
サービス部品供給なし
AV 1 2 1 NETWORK DC OUT Q250 C4
AV 7 AV 6 AV 5 AV 4 AV 3 AV 2 (1 BD/DVD) ARC (3 NET) Q251 C4
CB7 CB6 CB5 CB4 CB3 CB2 CB1 CB62 CB61
Q705 F5
2 DIGITAL (3) Q706 E6
(W391) CB932
232C_MISO
232C_MOSI

CB951
DGND
+3.3M

IC60 7 1
5
IC63
4
5 4 1
5 DAC

IC930
CB70 1 3
128 97 1 3 IC66 (CB851)
1 75 51 4
96 8 14 3
76 50
128 97
1 96
SVID_DET IC2 SR_MOSI5
+5VA IC62 SR_MISO5
ADSY VE 9
8 DAZ2L (IPL)
IC1 28 27 1 DAZ2E (RSENS)
VIDEO (1) 1

IC901
DAZ2R (IPR)
CB21

36 65 20
ADSC VE 4 1
DAZ2E (IPE)

IC955
CB9 IC956
32 65
(CB303) DASY 16
1 9 10 16 IPV
33 64 100 26 IPVE
DASC VE
19 11 15
IC934
IPSY

CB943
32 1 25 9 8 18
65
IPSC

IC902
5 8
10
33 64
DGND
1 D_OUT
75 51
16
AV1_D
76 50 8 56 29 AV2_D
3 VE 128 9
AV4_D AV3_D
DAPr 1 97 96

IC64
VE AUDIO1_D
DAPb AUDIO2_D
VE IC61 16
1 +5DSP
DAY IC4
VIDEO (1) VE
CB22

VE DACVBS
100
(CB302) 24 13

IC50
ADPr 25 32
AD_BCK

IC951
12 1 26 1
VE ADPb 65 25 10
AD_WCK
AD_SDO

IC953
33 64
+5VA IC20
+5A
ADY 36 1 IC65 Z2_ADL
VE 37 48 1 2 Z2_ADR
ADCVBS 11 20 ADE
4 3 NETL NETE

CB944
IC9
NETR
ADC_N_RST +3.3DSP
REM_IN2 DA_SD_CSW
L3_DET DA_WCK
PS1_PRT 32 17 8
7
DA_BCK
+3.3M 33 DA_SD_F

IC51
VID_PON HDMI_SCL 16 128 97 1 28 DGND
HDMI_SDA 1 96 14 CB952 DA_MCK
IR_OUT 1 DGND
IC21
EX_MOSI
CB71

5
EX_SCK 1

IC54
IC3
EX1_N_CS EX1_N_RST
48 49 1 24 13
4 NC 64 3
4
25 12
DAC

IC900
NC (CB852)
NC IC914

TUN_N_INT NC 32
33 64
65 10 6 14 8
36 1 11
10

TU_N_RST/HDR_N_RST 37 48

IC938
1 5 IC918 IC935
TU_SCL/HDR_MISO 4 1
TU_SDA/HDR_MOSI 1 3 2
20
1 7
176
VIDEO (1) 97
96 65
64 1 133 132

(CB335)
11 10
DAC

IC937
24
25 (CB854)
8 8 5 8 5 IC41
5 20 1
IC936 IC939 IC42

IC911
IC75
1 4 1 4 1 4 176 DA_SD_SB
128 32 33
1 133 132 DA_SD_SR
1 DA_SD_SW2
48 DA_SD_FP
1
DA_SD_RP
DGND SR_PON5
12 1
DAC_N_CS

CB945
48
89 DSP_SCK

IC920
13
+5.5V 132 89 3 1 44
DSP_MOSI
DAC_N_CS_FP
CB930

133 88 45 88
IC903
No replacement part available. IC915 DAC_N_CS_SW
5 DGND 4 5 1
16
24
25
36 37 N.C.
DAC_N_RST_F DAC_N_RST
サービス部品供給なし

IC76
20 11 20 11 54 28 DAC_N_RST_SB_FP DAC_MUTE_RP
8 9 MODEL
POWER IC72 IC70
IC79 2 3
8 5
44
89 R_200_DET

IC85
1 4 16 9 IC910 IC913 45 88
(W2003A)(W2003B) 1
• Semiconductor Location 10 1 10 IC77
1 4
8 5
IC921
Ref no. Location Ref no. Location 1 8 1 27 54 28

VBUS
D-
D+
GND
FG
20 11 20 11 176 CB923
45 2 1 4
D1 B2 D19 F2 3

IC86
1 44 IC922
IC73 IC71 4
+3.3M 1
D2 B2 D20 F2 DGND 1 10 1 10
ACPWR_DET 1
CB942

D3 B2 D21 F2 MCPU_N_RST
27

PRY THM1
D4 C2 D500 F3 3 3
OPERATION (2)

IC917
2 2

IC916
THM3

CB76
DEST 1 1
CB949 4 +3.3S (W4501)
D5 C2 D502 F3 4
DGND
AMPPOWER (1) (for service)
CB78

6 D6 C2 D503 E3 CB79

D7 C2 D601 G2 (W1806) CB75 AMP (4)

D8 C2 D602 G2
CB931
(Writing port) CB73 CB77 CB74 (W1001)

D9 D2 D604 G2 Ref no. Location

D10 D2 D607 G2 IC21 C4
+5USB
GND
+5USB
GND

+3.3MT
MT_F_MI
MT_Z2
MT_MZ
MT_SB_MI
MONO_N_Z3
VOL_MOSI
DGND
VOL3_CS
DGND
+3.3S
THM4
THM2

PS2_PRT
PS1_PRT
AMP_LMT
AMP_OLV
I_PRT
DC_PRT
EX_SCK
DGND
EX_MOSI
EX2_N_CS
EX2_N_RST
+3.3M
FLD_N_CS
FLD_MOSI
REM_IN1
IRB_GND
ISEL_RA
PS2_PRT
PSW_DET
KY_AD2
VDL_RB
FLD_PON
STBY_LED
+5.5
DGND
D11 D2 D610 G2 IC41 F5 Ref no. Location Ref no. Location
D12 D2 D9300 C6 IC42 D5 Q707 E6 Q9300 D6
AMP (5) OPERATION (2)
D13 D2 IC1 D3 IC50 F3 Q708 F6 Q9302 D5

+5D
DGND
VAUXD
(W1002)
(W4503)
D14 D2 IC2 C3 IC51 F4 Q709 E6 Q9304 D5
FLD_N_RST
FLD_SCK
MIC_N_DET
FLP_PON
IR_DATA
ISEL_RB
KY_AD3
KY_AD1
VDL_RA
PD_LED
+3.3M
+5.5
DGND
HP_N_DET
MT_Z3
MT_SB_PO
MT_EX1_MI
MONO_N_Z2
VOL1_SCK
VOL2_SCK
VOL3_SCK

D15 E2 IC3 E4 IC54 F4 Ref no. Location Ref no. Location Q710 E6 Q9305 I5
D16 E2 IC4 E3 IC60 G2 IC63 G2 IC66 G2 AMPPOWER (1) DAC Q9100 E6 Q9503 G6
7 (W1800) (W852)
D17 E2 IC9 E3 IC61 G3 IC64 G3 IC70 D5 OPERATION (1) Q9101 E6 Q9504 G6
FUNCTION (1) (CB401)
D18 E2 IC20 C3 IC62 F3 IC65 G3 IC71 D6 (CB705)

110
 A B C D E F G H I J
RX-A3020/RX-V3073

DIGITAL (1) (Side B) • Semiconductor Location

Ref no. Location
D501 F3
D700 F5
D701 E6
D702 F6
2 D703 E6
D704 E6
D9301 B5
D9302 B5
IC5 G3
IC56
IC10 I3
5 4 IC12
2 3
1 3 4 3 4
1 4 IC12 G3
1

IC57
3 2
2 1
IC22 H4

IC55
1 2
IC23 F4
4 3

IC10
IC24 F4
IC25 F4
3 IC53 D4
IC55 F3
14 8

IC5
IC56 E3
27 1
IC57 E3
1 7 IC78 E5
IC952
28 27 IC80 E5
28 54
IC81 F5
IC82 E6

IC53
2
IC22 3
4
IC83 E5
1
10 1 IC931 G6
4 1 IC25
IC933 H5
54 10 1 10 1
11 20 IC952 C3
IC24 IC23
Q1 H2
11 20 11 20
Q2 H2
Q3 H2
Q4 H2
Q5 G2
Q6 G2
Q7 G2
Q8 G2
Q9 F2
5 Q10 F2
4 1 Q11 E2
14 8
5 8
Q12 F2
IC83 IC78

1 14 14 8
Q15 E2

IC80
1
8 IC81
4
3 2
IC933 Q16 E2
7
1 7
8 7 Q252 H4

IC82
14 1
1 7
8
Q253 H4

IC931
1

4 5 Q700 E5
Q701 E5
Q702 E5
6 Q703 E5
Q704 E5
Q711 F5
Q712 F5
Q713 F5
Q714 F5
Q715 F5
Q716 F5
Q717 F5
Q718 F5
Q9301 H5
7

111
 A B C D E F G H I J
RX-A3020/RX-V3073

2 DIGITAL (2) (Side A) DIGITAL (3) (Side A)

DIGITAL (1)
VIDEO AUX (CB70)

232C_MOSI
232C_MISO
HDMI IN

DGND

+3.3M
CB30

3 9 8
W391

IC35
16 1
42 29
43 28 4 1
8
No replacement part available. IC30 5 IC33
サービス部品供給なし
56 15
1 14

1 6
4
IC31

CB31
3 4 CB35

RS-232C
Sheild
Data2+
Data2-
Sheild2
Data1+
Data1-
Sheild1
Data0+
Data0-
Sheild0
DataC+
DataC-
SheildC
CEC
F_HEQ_CE
SCL
+Vcc
+Vcc
+5.5V
+5VPower
HPD
FR_SCL
SDA

FR_SDA

DIGITAL (1)
(CB9)

• Semiconductor Location
Ref no. Location
D352 B4
IC30 C4
IC31 C4
IC33 D3
IC35 H3
Q351 D3
6 Q352 D3

112
 A B C D E F G H I J
RX-A3020/RX-V3073

2 DIGITAL (2) (Side B) DIGITAL (3) (Side B)

IC32
4
4 5
4 3
1 3
5 1
IC34

5 • Semiconductor Location
Ref no. Location
IC32 D4
IC34 C4

113
 A B C D E F G H I J
RX-A3020/RX-V3073

FUNCTION (1) (Side A)

PHONO AV 1 AV 2 AV 3 AV 4 AV OUT AUDIO 1 AUDIO 2 AUDIO 3 AUDIO 4 MULTI CH INPUT ZONE OUT/PRE OUT PRE OUT
(1 BD/DVD) (2 TV) FRONT SURROUND SUR.BACK CENTER/ ZONE 2/ ZONE 3/ FRONT SURROUND SUR.BACK SUBWOOFER CENTER
2 SUBWOOFER F.PRESENCE R.PRESENCE (SINGLE) (FRONT/REAR)
L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R 1/2

K, A, B, G, F, L models
3

DAC
(CB859)

DKL(DAZ2L)
DKR(DAZ2R)
DKE(DAZ2E)
SRL
SRR
SRE
VAUXL VAUXR
VAUXE
CB701

MIC
MICE
ADML
ADMR
4 ADZL
AGND
ADZR
AGND
NETZ2L
OPERATION (2)
NETZ2R (CB454)

HPR
E

W701
HPL
DAC HP_N_DET
(CB860)

NETZ3L
NETZ3R
AGND
DAFR+
DAFR-
DAFL+ AGND
DAFL-
5 AGND
CB702

DASR+
DASR-
AGND
DASL+
DASL- W703
DASBR+
DASBR-
AGND
DASBL+
DASBL-

DACT+
DACT-
DASW+/R
SWE
DASW-/L
FPE
CB703

DAFPR
DAFPL
DARPR
RPE
DARPL
-12V W709 W708
-12V
+12V CB705
+12V
6
DAC
(CB861)

VOL3_SCK
VOL2_SCK
VOL1_SCK
MONO_N_Z3 MONO_N_Z2
MT_EX1_MI
MT_SB_PO
MT_Z3
HP_N_DET

MIEX1R
MISBR
E
MISR
E
MIFR

E
MIEX1L
MISBL
E
MISL
MIFL
E
MICT
C, R, T, K, A, B, G, F, L, S, J models
• Semiconductor Location
Ref no. Location
+5T
TUR
TUE
TUL

VOL3_CS Q7409 D5
DGND
VOL_MOSI

MT_SB_MI
MT_MZ
MT_Z2
MT_F_MI
+3.3MT
VIDEO (1) AMP (2) AMP (1) Q7410 D5
(CB333) (CB112) (CB113)
Q7622 D5
Q7701 I4
Q7702 I4
DIGITAL (1)
7 (CB73)

114
 A B C D E F G H I J
RX-A3020/RX-V3073

• Semiconductor Location
FUNCTION (1) (Side B) Ref no. Location
D7401 E5
D7402 F4
D7403 C5
D7404 C5
D7601 D6
2 IC701 B3
IC713 F3
IC724 B4
IC726 B5
IC727 B5
IC728 B6
IC741 D4
IC742 D6
IC743 G4
IC761 H4
3 8 5 IC762 I3
4 1 IC713 IC763 H4
Q7401 F5
IC701 1 4

5 8 51 50
4 1 Q7402 F5
IC762 Q7403 E4
5 8
Q7404 E4
4 1
31
30
Q7405 F5

1
IC761
Q7406 F4

74
80

IC
5 8
81
Q7501 H6
Q7502 H6
100 1 Q7503 H6
4 8 5 Q7504 H6
IC763
Q7505 G6
4 1 1 4
15 1 Q7506 H6
IC724
5 8 Q7507 G6
IC743 Q7508 H6
Q7509 G6
16 30
Q7601 G3
4 1 Q7602 G3
5
IC726
8 Q7603 G3
Q7604 G3
5 Q7605 H3
Q7606 H3
4 1 Q7607 H3
51 50
IC727 Q7608 I3
5 8
Q7609 G3
31 Q7610 G3
4 1 2 30
74 Q7611 G3
80 IC
81
IC728 Q7612 G3
5 8
Q7613 G3
100 1
Q7614 G3
Q7615 H3
6 Q7616 H3
Q7617 H3
Q7618 H3
Q7619 H3
C, R, T, K, A, B, G, F, L, S, J models
Q7620 I3
Q7621 I3
Q7703 H4
Q7704 H4
Q7705 H5
Q7706 H5
7 Q7707 I4
Q7708 I4

115
 A B C D E F G H I J
RX-A3020/RX-V3073

FUNCTION (2) (Side A)

2
AV 1 AV 2 AV 3 AV 4 AV OUT AUDIO 1 AUDIO 2
COAXIAL COAXIAL OPTICAL OPTICAL OPTICAL COAXIAL

DGND
3 +5D
AUDIO2
AUDIO1
AV4
AV3
AV2
AV1
AVOUT
SR_PON5
SR_MOSI5
SR_MISO5
SRE
SRR
SRL

DAC
(CB858)
4 W782A

116
 A B C D E F G H I J
RX-A3020/RX-V3073

FUNCTION (2) (Side B)

7 1
• Semiconductor Location
3 14 8
Ref no. Location
IC781 IC782

8 14
IC781 C3
1 7 IC782 D3

117
 A B C D E F G H I J
RX-A3020/RX-V3073

OPERATION (1) (Side A)

Remote control
sensor
DIGITAL (1)
(CB77)

FLD_N_RST HDMI Through/iPod Charge

FLD_N_CS indicator
FLD_SCK
FLD_MOSI
MIC_N_DET
REM_IN1
3 IRB_GND
FLP_PON
IR_DATA
ISEL_RA
ISEL_RB
PS2_PRT
CB401

KY_AD3
PSW_DET
KY_AD1
KY_AD2 SW425 MAIN ZONE
VOL_RA
VOL_RB
PD_LED
FLD_PON
+3.3M
STBY_LED
+5.5
+5.5
DGND DGND

FLP_PON
FLAC
4 FLAC

W4005
VOL_RA FGND
VOL_RB 44V
CB405

DGND SCENE TONE/ DGND

PSW +5.5
PD_LED
PRESET INFO 4 3 2 1 STRAIGHT BALANCE OPTION ON SCREEN
SW401

SW404

+5.5

SW403
SW402

SW414
SW409
SW407

CB402
SW410

SW408
SW405

SW406
SW411
CB404
SW412 VIDEO (3)
(CB362)
OPERATION (3) MEMORY

+12V
MICE
MIC_N_DET

ISEL_RA
ISEL_RB
+3.3M
DGND
SW421 SW418 SW428 SW426
(CB461) MULTI ZONE
SW415

SW423

SW420
SW424

SW417
SW413 SW416

TUNING SW430 OPERATION (4)

ENTER (CB471)
OPERATION (2)
ZONE ZONE 4 ZONE 3 ZONE 2 PROGRAM (CB453)
5 AM FM CONTROL SW429 SW427

DISPLAY RETURN

6
• Semiconductor Location
Ref no. Location
D4001 I3

118
 A B C D E F G H I J
RX-A3020/RX-V3073

OPERATION (1) (Side B)

4 3
4 1
2
IC401

• Semiconductor Location
Ref no. Location
D4002 B3
6 D4003 A3
D4006 F3
D4007 F3
IC401 B4
Q4001 H3
Q4002 B3

119
 A B C D E F G H I J
RX-A3020/RX-V3073

DAC
(CB856) FUNCTION (1) OPERATION (1)
OPERATION (2)

DGND
(Side A)

AUXE

AUXV
AUXY
AUXC
(W701) (CB402)

-12V
+5D

MIC

MIC N_DET
HP_N_DET
AUXVE
AUXVE
VAUXD
AUXR
AUXL
MICE

MICE
+12V

+12V
HPR
HPE
HPL
CB453

2 CB452

GND
+5USB
GND
+5USB
CB454

W4503 DIGITAL (1)

(CB931)

JK451

W4501

FG
GND
+Data
-Data
VBus
3
DIGITAL (1)
(CB952)

JK453

CB455

4
OPTICAL R AUDIO L VIDEO PHONES YPAO MIC USB
SILENT CINEMA (Front)
VIDEO AUX

OPERATION (3) (Side A) OPERATION (4) (Side A)

OPERATION (1)
(CB404)
5

ISEL_RA
ISEL_RB

DGND
+3.3M
CB471

SW471
SW462
SW461

6 INPUT

PURE DIRECT PURE DIRECT

VOLUME indicator
CB461

• Semiconductor Location
+5.5
PD_LED
PSW
DGND
VOL_RB
VOL_RA

Ref no. Location

D4603 E6
OPERATION (1)
(CB405)
7

120
 A B C D E F G H I J
RX-A3020/RX-V3073

OPERATION (2) (Side B)

8 5

IC451

1 4
• Semiconductor Location
Ref no. Location
D4501 C3
D4502 C3
3 D4503 D3
D4504 D3
D4506 C3
D4507 E3
D4508 E3
D4509 F3
D4510 E3
D4512 F3
D4514 F3
IC451 G2
Q4501 G2
4
Q4601 E6

OPERATION (3) (Side B) OPERATION (4) (Side B)

121
 A B C D E F G H I J
RX-A3020/RX-V3073

AMP (1) (Side A) AMPPOWER (1)

(W1808B)
AMPPOWER (1)
(W1808A)

AMPPOWER (1)
(W1809)

+B

CB108
CB111

3 +B

CB105
-B

CB107
CB109
-B For service
CB106 For service
For service For service
I_PRT_L For service
W1005

-LB_L W1517A
+LB_L W1522A
W1521A

AMPPOWER (1)
(CB180) W1518A

AMP (3) BL W1519A

(W1518B)

4
W1520A
CB113

BR GY BL WH YE AMP (4) (Side A)

C
E AMP (3) AMP (3) AMP (3) AMP (3) AMP (3)
FL (W1519B) (W1521B) (W1517B) (W1520B) (W1522B)
SL
E
SBL
EX1L
6 E
• Semiconductor Location
IC100
FUNCTION (1) Ref no. Location Ref no. Location Ref no. Location OUT GND VCC
(W708)
IC100 J6 Q1067 E4 Q1075P F2 DGND

W1001
IC102 J7 Q1068 F4 Q1077N H2 +3.3S
THM3
Q1060 B4 Q1069 H4 Q1077P F2 THM1
VCC GND OUT
Q1061 C5 Q1070 F4 Q1079N C2
IC102
Q1062 E4 Q1071 H4 Q1079P B2 DIGITAL (1)
Q1063 F5 Q1072 B4 Q1081N D2 (CB76)

Q1064 H5 Q1073 D4 Q1081P D2 C model

7 Q1065 B4 Q1074 E4 Q1083N E2
Q1066 D4 Q1075N G2 Q1083P E2

122
 A B C D E F G H I J
RX-A3020/RX-V3073

AMP (1) (Side B)

• Semiconductor Location
2
Ref no. Location Ref no. Location
D1024 B5 Q1040 B5
D1025 C5 Q1041 C4
D1026 E5 Q1042 E4
D1027 F5 Q1043 F4
D1028 H5 Q1044 H4
D1029 B4 Q1045 B5
D1030 B4 Q1046 C5
D1031 C5 Q1047 D5
D1032 C5 Q1048 F5
3 D1033 D4 Q1049 G5
D1034 D4 Q1050 B5
D1035 F5 Q1051 C5
D1036 E5 Q1052 E5
D1037 G5 Q1053 F5
D1038 G5 Q1054 H5
D1039 F4 Q1055 B4
D1040 G4 Q1056 C4
D1041 B4 Q1057 D4
D1042 C4 Q1058 F4
D1043 D4 Q1059 G4
4
D1044 H3 Q1085 H3
D1045 G3 Q1086 G3
D1046 C4 Q1087 C3
D1047 D3 Q1088 D3
D1048 E4 Q1089 E3

AMP (4) (Side B)

C model
7

123
 A B C D E F G H I J
RX-A3020/RX-V3073

AMP (2) (Side A) AMPPOWER (1) AMPPOWER (1)

(W1807B) (W1807A)

3
CB104

CB103
CB102 CB101
For service I_PRT_R
For service

W1003
For service -LB_R
For service +LB_R
W1516A

W1514A W1512A
AMPPOWER (1)
(CB181)
W1515A GY
AMP (3)
(W1512B)

4
W1513A

CB112
BR RE BL OR AMP (5) (Side A)
FR
AMP (3) AMP (3) AMP (3) AMP (3)
(W1514B) (W1516B) (W1513B)
E
(W1515B)
SR
E
SBR
EX1R
6
• Semiconductor Location FUNCTION (1) IC101
(W709) OUT GND VCC

Ref no. Location Ref no. Location Ref no. Location

DGND
Q1022 E4 Q1030N G2

W1002
IC101 J6 +3.3S
IC103 J7 Q1023 B4 Q1030P G2 THM4
THM2
Q1016 B4 Q1024 G4 Q1032N F2 VCC GND OUT

Q1017 G5 Q1025 F4 Q1032P E2 IC103

DIGITAL (1)
Q1018 E5 Q1026 D4 Q1034N E2 (CB75)
Q1019 D4 Q1027 C4 Q1034P D2
C model
7 Q1020 D4 Q1028N C2
Q1021 G4 Q1028P C2

124
 A B C D E F G H I J
RX-A3020/RX-V3073

AMP (2) (Side B)

• Semiconductor Location
Ref no. Location Ref no. Location
D1000 C5 Q1000 G4
D1001 D5 Q1001 E4
D1002 G5 Q1002 D4
D1003 E5 Q1003 B4
D1008 C4 Q1004 G5
3
D1009 C4 Q1005 E5
D1010 G5 Q1006 D5
D1011 G5 Q1007 B5
D1012 E5 Q1008 G5
D1013 E5 Q1009 E5
D1014 B5 Q1010 D5
D1015 B5 Q1011 C5
D1016 F4 Q1012 G4
D1017 D4 Q1013 E4
D1018 B4 Q1014 D4
4 D1019 E4 Q1015 B4
D1020 C3 Q1036 C3
D1021 F3 Q1037 F3
D1022 D4 Q1038 D3
D1023 G3 Q1039 G3

AMP (5) (Side B)

C model
7

125
 A B C D E F G H I J
RX-A3020/RX-V3073

AMP (3) (Side A)

AMPPOWER (1)
(W1803A)(W1803B)

AMPG

AMPG
2

AMPPOWER (1)
(W1810)

SPRY_F_RP_CTRL
SPRY_ZRP_CTRL

SPRY_ZFP_CTRL

SPRY_SR_CTRL
SPRY_SB_CTRL
SPRY_C_CTRL
SPRY_F_CTRL
AMP (1) AMP (2) AMP (1) AMP (1) AMP (2) AMP (1) AMP (2) AMP (2)

AMP_OLV
(W1520A) (W1514A) (W1518A) (W1517A) (W1516A) (W1522A) (W1515A) (W1513A)

DC_PRT
RYB-
WH RE BU BL BL BL YE BR OR

3
CB114
W1519B

AMP (1) BR

W1520B
(W1519A)
W1512B

W1517B
AMP (2) GY CB110
(W1512A)

W1518B
W1514B

W1516B

W1515B
W1522B
FPR

W1521B

W1513B
W1523

FPL
4 RE
LE
(for service) GY AMP (1)
(W1521A)

W1526B
AMPPOWER (2)
(CB194)

W1526A
5

+/- +/- +/- +/- +/- +/- +/- +/- +/-

L R L R L R L R

FRONT CENTER ZONE 2/ZONE 3/R. PRESENCE SURROUND BACK SURROUND

SPEAKERS

126
 A B C D E F G H I J
RX-A3020/RX-V3073

AMP (3) (Side B)

• Semiconductor Location
Ref no. Location
D1512 C3
D1513 H4
D1514 G4
D1515 D3
6 D1516 H4
D1517 C3
D1518 G3
D1519 E3
D1520 C3
D1521 C3
D1523 E3
D1524 H3
D1526 F3
D1527 B3
D1528 B3
7
D1529 B3

127
 A B C D E F G H I J
RX-A3020/RX-V3073 Safety measures 安全対策
• Some internal parts in this product contain high voltages and are dangerous. Be sure to take safety measures during servicing, such ・ この製品の内部には高電圧部分があり危険です。修理の際は、絶縁性の手袋を使用するなどの安全対策を行ってください。
as wearing insulating gloves. ・ 下記のコンデンサには電源を OFF にした後も電荷が残り、高電圧が維持されており危険です。修理作業前に放電用抵抗
• Note that the capacitors indicated below are dangerous even after the power is turned off because an electric charge remains and a （5 k Ω /10 W）を下記の各コンデンサの端子間に接続して放電してください。放電所用時間は各々約 30 秒間です。
1 high voltage continues to exist there. Before starting any repair work, connect a discharging resistor (5 k-ohms/10 W) to the terminals AMPPOWER（1）P.C.B. の C1822 1828
of each capacitor indicated below to discharge electricity. The time required for discharging is about 30 seconds per each.
C1822-1828 on AMPPOWER (1) P.C.B.

AMPPOWER (1) (Side A)

POWER TRANSFORMER
AMP (3) POWER TRANSFORMER POWER TRANSFORMER
5 k-ohms 5 k-ohms
(CB110)
10 W 10 W
BL BL (for service)
2
CB182
CB189
CB190

W1803B W1803A

CB188

5 k-ohms
10 W

AMP (1)
(ST101)
3 POWER TRANSFORMER AMP (1)
(ST102)
W1807A

IC180 IC181
W1808A
OUT COM IN OUT COM IN

W1809
CB200 W1808B W1807B

DAC
(CB855)
4
+5A
AG2_SENS
AG2_RETURN

W1801
CB180
+12V

CB181
AG1_SENSE
-12V
CB202

AG1_RETURN

CB203
CB193

(for service) TRG_GND

+18V
-7V

W1802
V_GND
+7V

W1800
IC183
5
W1806

VIDEO (1)
(CB331)
W1810
RYB-
SPRY_ZRP_CTRL
SPRY_F_RP_CTRL
SPRY_ZFP_CTRL
SPRY_C_CTRL
SPRY_F_CTRL
SPRY_SB_CTRL
SPRY_SR_CTRL
AMP_OLV
DC_PRT

DGND 5 k-ohms 5 k-ohms AMP (2) 5 k-ohms 5 k-ohms

+5.5V DST
PRY +3.3M (ST103)
EX2_N_RS 10 W 10 W +B 10 W 10 W
MCPU_N_RST +LB_L +LB_R
ACPWR_DET EX2_N_CS
POWER -LB_L -LB_R EX_MOSI +B
DGND I_PRT_L I_PRT_R
6 (W2005) +3.3M
DGND AMP (2) -B
EX_SCK (ST104) -B
DC_PRT • Semiconductor Location
AMP (1) AMP (2) I_PRT
DIGITAL (1) (W1005) (W1003) AMP_OLV AMP (1)
POWER (CB942) AMP_LMT Ref no. Location Ref no. Location
AMP (3) PS1_PRT (CB111)
(W2004A)(W2004B) D1807 H5 Q1806 H3
(CB114) PS2_PRT
D1808 D3 Q1808 D4
DIGITAL (1) D1809 G4 Q1809 D4
(CB74) D1810 H4 Q1810 D5
IC180 H3 Q1811 E5
IC181 H3 Q1815 E4
IC183 C5 Q1836 C5
7 Q1804 I3 Q1839 D5
Q1805 I3

128
 A B C D E F G H I J
RX-A3020/RX-V3073

AMPPOWER (1) (Side B)

3 1

4 5

12 1

5
IC182
13 24

• Semiconductor Location
6
Ref no. Location Ref no. Location Ref no. Location Ref no. Location
D1801 I4 D1818 C5 Q1814 H4 Q1827 C5
D1802 H4 D1819 C5 Q1818 D5 Q1828 D5
D1803 H4 D1820 C4 Q1819 C5 Q1829 D5
D1804 D5 D1821 D4 Q1820 D5 Q1830 D5
D1805 D5 D1822 D5 Q1821 C5 Q1831 D5
D1811 C2 IC182 E5 Q1822 C2 Q1832 D5
D1814 B5 IC184 B5 Q1823 D5 Q1833 D5
D1815 C5 Q1807 E4 Q1824 D5 Q1837 C5
D1816 B5 Q1812 I4 Q1825 C5
7
D1817 C5 Q1813 H4 Q1826 C3

129
 A B C D E F G H I J
RX-A3020/RX-V3073

AMPPOWER (2) (Side A) AMPPOWER (3) (Side A) AMPPOWER (4) (Side A)

R, S models

2 SPEAKERS
VOLTAGE SELECTOR
ZONE 2/ZONE 3/F. PRESENCE/BI-AMP
R L 220V – 240V 110V – 120V
+/- +/-

3 CB198 CB199

CB201

OR
PU

RE
YE
POWER TRANSFORMER

AMPPOWER (5) (Side A)

LE
CB194

RE
FPL
5
FPR

AMP (3)
(W1523)

130
 A B C D E F G H I J
RX-A3020/RX-V3073

AMPPOWER (2) (Side B) AMPPOWER (3) (Side B) AMPPOWER (4) (Side B)

R, S models

AMPPOWER (5) (Side B)

131
 A B C D E F G H I J
RX-A3020/RX-V3073 Safety measures 安全対策
• Some internal parts in this product contain high voltages and are dangerous. Be sure to take safety measures during servicing, such ・ この製品の内部には高電圧部分があり危険です。修理の際は、絶縁性の手袋を使用するなどの安全対策を行ってください。
as wearing insulating gloves. ・ 下記のコンデンサには電源を OFF にした後も電荷が残り、高電圧が維持されており危険です。修理作業前に放電用抵抗
• Note that the capacitors indicated below are dangerous even after the power is turned off because an electric charge remains and a （5 k Ω /10 W）を下記の各コンデンサの端子間に接続して放電してください。放電所用時間は各々約 30 秒間です。
1 high voltage continues to exist there. Before starting any repair work, connect a discharging resistor (5 k-ohms/10 W) to the terminals POWER P.C.B. の C2016
of each capacitor indicated below to discharge electricity. The time required for discharging is about 30 seconds per each.
C2016 on POWER P.C.B.

5 k-ohms
10 W
POWER (Side A)
2

IC203

IC204

+5.5V
DGND
W2005

AMPPOWER (1)
W2003A W2003B (CB202)

RE GY
DIGITAL (1)
4 (CB930)
W2002

+5.5V
DGND
5
VIDEO (3)
(CB361)

AC IN • Semiconductor Location
6
CB204

Ref no. Location

D2001 D3
D2002 F3
D2004 E4
D2010 E5
CB205

IC203 G3
W2004A W2004B IC204 G3
Q2001 F4
BU WH

7 AMPPOWER (1)
(CB193)

132
 A B C D E F G H I J
RX-A3020/RX-V3073

POWER (Side B)
2

9
16

IC201

1 8
K R A
3

IC205
4

• Semiconductor Location
6 Ref no. Location
D2003 F3
D2006 E4
D2007 F3
D2016 F3
IC201 E3
IC205 G3

133
 A B C D E F G H I J
RX-A3020/RX-V3073

VIDEO (1) (Side A)

J model

AV 1 AV 2 AV 3 AV 4 AV OUT MON.OUT/ D4 VIDEO COMPONENT VIDEO MONITOR OUT/

(1 BD/DVD) ZONE OUT ZONE OUT
AV 1/AV 2 AV 3/AV 4
REMOTE TRIGGER OUT
Y PB PR Y PB PR Y PB PR
1 2
2
IN OUT IN OUT 1/2

JK331 JK332 JK333 JK334 JK335

JK301 JK302 CB301

3
DIGITAL (1)
(CB22)

DGND
DAPr
DAPb VE
VE
DAY
VE

CB302
ADCVBS
VE
ADPr
VE
CB303 ADPb
+5VA
ADY
VE
ADCVBS

REM_IN2
L3DET
PS1_PRT
+3.3M
VID_PON
HDMI_SCL
HDMI_SDA
IR_OUT

CB335
EX_MOSI
EX_SCK
EX1_N_CS
EX1_N_RST
N.C.
N.C.
N.C.
N.C.
TUN_N_INT
TU_N_RST/HDR_N_RST
TU_SCL/HDR_MISO
TU_SDA/HDR_MOSI

5 DIGITAL (1)
(CB71)

1 4 1 4

IC331 IC332

CB304 CB333 CB332 CB334 CB331

• Semiconductor Location
Ref no. Location
6
AUXC
R_200_DET
AUXY
AUXVE
AUXV
+3.3V
IPV
-3.3V
IPSY
IPVE
IPSC

+5T
TUR
TUE
TUL

TRG_GND
+18V
-7V
VGND
+7V
SDA
HDR_MOSI
NC
+3.3HDR
AUDIO_L
AUDIO_R
+5T
GND
GPI02
SDA

U model D3310 H3
D3311 H3
IC331 E6

DASC
DASY
ADSC
ADSY
SVID_DET
DAC FUNCTION (1) AMPPOWER (1) IC332 F6
SCL
HDR_MISO
RESET
HDG
HDG
AUDIO_M
HDG
+5V
ROUT
NC
SCL
RST

(W703) (W1802)
(W851) Q3304 G6
Q3308 H3

VE
VE
VE
+5VA
AM/FM TUNER Q3308 H3
(C, R, T, K, A, B, G, F, L, S, J models) HD RADIO TUNER DIGITAL (1)
(U model) (CB21)
Q3315 I3
Q3316 I3

134
 A B C D E F G H I J
RX-A3020/RX-V3073

VIDEO (1) (Side B)

2
J model

16 9 16 9
IC303 IC301

1 8 1 8

51 50

14 8
IC307
31
16 9 16 9

5
30

30
1 7

IC
IC304 IC302 80
81
1 8 1 8
4
100 1

16 9 24 13 • Semiconductor Location
IC306
IC308
7
1 Ref no. Location Ref no. Location
1 12
IC309 1 8 D3001 A3 IC302 B4
D3002 B3 IC303 B3
8 14
D3003 B3 IC304 B4
D3004 B3 IC305 D4
5 D3005 A3 IC306 G4
D3006 B3 IC307 C4
D3007 B3 IC308 C4
D3008 C3 IC309 B5
D3017 C4 Q3001 C3
D3018 C4 Q3002 C3
D3302 H3 Q3003 C3
D3303 E5 Q3004 G5
D3304 E5 Q3303 F6
D3306 G3 Q3305 F6
D3307 H3 Q3306 F6
6 D3308 G3 Q3310 G3
U model
D3309 H3 Q3311 H3
D3312 H2 Q3312 I3
D3313 H2 Q3313 H3
D3314 H3 Q3314 I3
D3315 D6 Q3317 H3
D3318 H5 Q3318 I3
D3319 H5 Q3319 G4
IC301 B3

135
 A B C D E F G H I J
RX-A3020/RX-V3073

VIDEO (3) (Side A) VIDEO (3) (Side B)

2

OPERATION (1)
(W4005)

FLP_PON
POWER

DGND

FGND
(W2002)

FLCA
FLCA

DGND
+44V
5.5

5.5
CB362 CB361

• Semiconductor Location
Ref no. Location
D3601 H5
4 D3602 G4
D3603 G4
D3604 G4
D3605 G4
D3606 G4
D3607 G4
D3608 G3
D3609 G4
Q3601 G5
Q3602 H5
Q3603 G5
5
Q3604 G5
Q3605 G4
Q3606 D4
Q3607 G3
Q3608 D3

136
 A B C D E F G H I J
RX-A3020/RX-V3073

1
DAC (Side A) DAC (Side B)

FUNCTION (2)
(CB781)

SRL DIGITAL (1)

SRR (CB943)
SRE
SR_MISO5
2 SR_MOSI5
SR_MOSI5
SR_PON5 SR_MISO5
DAZ2L

CB858
AVOUT 8 5 1 DAZ2E
16
AV1 DAZ2R

IC871
AV2 IC855 DAZ2E
9 IP_V
AV3 IP_VE
AV4
8 IP_SY

CB851
1 4 IP_SC
AUDIO1 DGND 3 4
AUDIO2 D_OUT IC870
FUNCTION (1) AV1_D
+5DSP AV2_D
(CB701)
AV3_D 2 1
DGND AV4_D
AUDIO1_D
AUDIO2_D
5 +5DSP
8 IC880
DKL DKR

CB859
DKE 1 4
SRL 15 14
SRR SRE AC_BCK
AD_WCK

IC872
AUXL AD_SDO
AUXR +5A
AUXE Z2_ADL
MIC Z2_ADR
3 MICE
ADML 8 IC881
5
28
1 AD_E
NETL
ADMR NETE

CB852
AGND NETR
ADZ2L 1 4 3.3DSP
ADZ2R ADC_N_RST
NETE DA_SD_CSW
NETL DA_SD_WCK
NETR DA_BCK
DA_SD_F
15 14 DGND
DA_MCK
FUNCTION (1) 4 1 5 DGND

IC873
8 IC883
(CB702) IC851
5 8 1 4 28
1 DIGITAL (1)
AGND IC853 (CB944)
AGND AGND 4 1
DAFR+
DAFR- 5 8
DAFL+ AGND
5
8 IC884 • Semiconductor Location
AGND DAFL- 15 14
CB860

DASRR- DASRR+
1 4 Ref no. Location
4 AGND

IC874
DASRL+
DASRL-
D8703 D2
DASBR+ 28
AGND
DASBR- 1 D8704 D2
DASBL+ 5
DASBL- 8 IC885
DA_SD_SB D8705 G6
DA_SD_SR
1 4 DA_SD_SW2
DA_SD_FP D8706 G6
DA_SD_RP
DACT+
DACT- SR_PON5
DGND IC851 B3
DASWR SWE 15 14 DAC_N_CS
DSP_SCK IC853 D4

CB854
DASWL DSP_MOSI
IC875

FPE 5 DAC_N_CS_FP
DAFPR DAFPL 8 IC886 DAC_N_CS_SW IC855 C2
CB861

N.C. DAC_N_RST_F
DARPR RPE 1 4
28
1 DAC_N_RST IC856 C5
DARPL DAC_N_RST_SB_FP
-12V DAC_MUTE_RP
-12V MODEL IC857 C5
+12V R_200_DET
+12V IC870 G2
5 14 1
5
8
IC887 DIGITAL (1) IC871 D2
FUNCTION (1) 1 4 IC876 (CB945) IC872 D3
(CB703)
15 28 IC873 D3
IC874 D4
1
8
1
8 IC875 D5
AMPPOWER (1)
IC857

IC856

1 8 14 1 IC876 D5
IC893

4
5
4
5 (W1801)
4 5 IC877 IC877 D6
15 28 +5A IC879 D6
AG2SENSE
AG2RETURN
IC880 C3
CB855

9 8 +12V IC881 C3
IC879

AG1SENSE IC883 C3
16 1 -12V
6 AG1RETURN IC884 C4
W851
IC885 C4
VAUXD IC886 C5
W852

DGND
+5D IC887 C5
IC893 B6
DIGITAL (1)
CB856
(CB923)
IP_SC0
IP_VE
IP_SY0
-3.3V
IP_V0
+3.3V
AUXV
AUXVE
AUXY
R_200_DET
AUXC

AUXVE
AUXVE
+12V
MICE
AUXL
AUXR
VAUXD
AUXC
AUXY
AUXV
MIC
-12V
AUXE
DGND
+5D

7
VIDEO (1)
(CB304) OPERATION (2)
(CB452)
137
 RX-A3020/RX-V3073

■ PIN CONNECTION DIAGRAMS

r
*$T r
*$T
AD8192ACPZ ADV7172KSTZ ADV7619KSVZ BA15218F CS230011-CZZR D80YK113CPTP400 TC74HC4051AFEL TC74LCX125FT TC74LCX245FT TC74VHC157FT TC74VHC273FT (EL,K) TC74VHCU04FT
48 37
ADV7630KSVZ
43 42 TC74HC4052AF
1 36
96 65
56 8 4 132 89
29 97 64 1 10 133 88
1 28 5
10 8
12 25 BD7542F-E2 8
16 20 10 7
1 16 7 20 14
14 15 14
13 24
1 1 1 1
43 56 1 1
ADV7181CBSTZ 8 4 DSD1791DBR
42 1 48 33 128 33
1 DSD1796DBR TC7WH04FU TRS3221ECPWR VHD1900EVG W25Q80BVSSIG
49 32 1 32
BD9328EFJ 96 65
AK5386VT BD9329AEFJ-E2 97 64
176 45
29 14 14
28 1 44
64 17 16
28 15 8 8 4
1 1 8
1 16 1 8
4 16 8 4
DM860A-AQE 18 1 EN29LV640AB-90TIP EP4CE15F23C6N FHP3350IM14X 1 1 128 33 1
22 1
A A
1 48 1 32

AB 22
V 18
14 7
A 1 24 A 1
25
1
V AB r
%JPEFT
KIA7812API KIA7912PI LAN8700C-AEZG-TR LM19CIZ/LF LM833MX L6566BTR M12L2561616A-5TG2A 1SS355VMTE-17 BAV103 D1NL20U-5083 D2SBA60-7001 D4SBS6-7101 4A 60V HZU15B2 TRF-E
NJU7313AM M12L64164A-5TG 1SS400TE61 D5SBA60 5A 600V
27 19
D15XBN20
54 28
28 27
Anode Anode Anode
28 18
36 19 Anode
14
1 18
8 4 28 – –
+VS Cathode AC
IN GND 9 10 36 10 VOUT Cathode Cathode AC Cathode
1 AC
OUT OUT GND + + AC
COM 1 1 27
IN
1 9
P6KE200ARL RB215T-60 RB501V-40 RF101L2STE25 STTH110A UDZS6.2B 6.2V UDZV4.3B
MFI341S2162 MX29GL256FLT2I-90Q NJM2068MD-TE2 NJM2388F33 NJM4565M (TE1) NJW1327FU1 RB521S-30 UDZS13B 13V UDZV5.1B
80 51 UDZV5.6B
81 50 Anode Anode UDZV7.5B
1 56 Anode Anode Anode UDZV8.2B Anode
15 11 UDZV22B
16 10

Cathode
8 4 Cathode 1 Cathode Cathode Cathode Cathode
20 6 2
8 4 3
5 1 1
1 1
1. VIN 4
28 29 2. VOUT 100 31
3. GND
4. ON/OFF CONTROL 1 30

NE5532DR NT5SV8M16HS-6K NJM431U PCA9517ADP PCM1781DBQR PCM5101PWR

54 28

r
5SBOTJTUPST
1
2
3 1: REFERENCE
2N5401C-AT/P 2N5401S-RTK 2N5551C-AT 2N7002KA-RTK/P 2SA1208S/T-AE 2SA1576A 2SA1708 2SC1815 Y 2SB1257 2SC2910S/T-AE
10 2SA1576UBTLR 2SC4488 2SD2014
2: ANODE 8
8 4
3: CATHODE 8 4 16 20
1 1 1 1
1 27

R5F6416MADFE R1163N501B-TR-FE R1172H121D-T1-F R1EX25512ATA00A R2A15220FP C G C

PCM9211PTR
R1172N301D-TR-F R1172H501D-T1-F E
132 89 D E
R3112N421A-TR-F B B
E B S C
36
133 88 R3116N271A-TR-F C B
CE
E E E E
25 B C CB B C
B CE B
37 24 80 51

1 81 50
2SC2712-Y (TE85R, F) 2SC3906K 2SC4081 T106 2SC4081UBTLR 2SC5964-TD-E 2SD2704 K 2SK208-Y DTA044EUBTL DTC114EKA HN4B01JE
4 1: CE DTC014EUBTL DTC144EKA
2: GND 2SC3326-A (TE85R, F)
5 3 8
3 3: NC
4
2SC3326-B (TE85R, F) 4
5 4: VDD
1 5: VOUT 2SC4213-A/B TE85L 3 5
48 13 4 1 3
100 31 3
1 12 C C 1 1
C C C G 2
176 45 1 30
1 2 1. BASE 1 (B1)
E E E D 2. EMITTER (E)
E E
1 44 B 1: IN 1: GND 3. BASE 2 (B2)
B B B B C 2: GND
E B S 2: IN 4. COLLECTOR 2 (C2)
R5F213G1DN400SP#W4 RP130Q121D-TR-F RP132S331D-E2-FE SiI9136CTU-3 SN74LV32APWR SN74LV4051APWR SN74LVC08APWR 3: OUT 3: OUT 5. COLLECTOR 1 (G2)
RP130Q181D-TR-F 75 51 SN74LV132APWR
RP130Q251D-TR-FE HN4C06J KRA304-RTK/P KTA1046-Y-U/PFY KTA1504S MCH6336-TL-E RAL035P01 STF9NK90Z STD05P STD05N μPA672T-T1-A
RP130Q331D-TR-F 76 50 KRC104S-RTK KTA1659A-U/PF KTC3875S
RP130Q501D-TR-F KRC404-RTK/P KTC4370A-Y-U/PF
4 4 4 4
5 6 6 6
3 3
12 14 3 3
3 8 OUT C 1
7 7 1 1 1
24 4 6 14 16
2 E 1. Drain
3 1 COMMON 1. DRAIN 1. Source 1 (S1)
1 1 1. BASE 1 (B1) 2. Drain
1 2. EMITTER (E) 2. DRAIN 2. Gate 1 (G1)
1 1 IN B 3. Gate
100 26 3. BASE 2 (B2) 3. GATE 1 1 3. Drain 2 (D2)
4. Source 4. SOURCE 23 23 4. Source 2 (S2)
4. COLLECTOR 2 (C2) GD 45 45
5. COLLECTOR 1 (G2) 5. Drain 5. DRAIN S 5. Gate 2 (G2)
BC 6. Drain 6. DRAIN 6. Drain 1 (D1)
1 25 E

138
 A B C D E F G H I J K L M N
RX-A3020/RX-V3073
SCHEMATIC DIAGRAMS
DIGITAL 1/10
1
IC1, 2: ADV7630KSVZ
4:2 3-GHz Xpressview HDMI crosspoint mux

RXC-5V
RXD-5V
VGA-5V
RXA-5V
RXB-5V
HPA_C
HPA_D
HPA_A
HPA_B

INT1
CEC
78 76 74 72 77 75 73 71 10 8

DDCA_SCL
DDCB_SCL
63
61 5V DETECT
Page 140 K7
CEC INTERRUPT TX EDID
DDCC_SCL 59 VOLTAGE REG.
DDCC_SCL 57
EDID
REPEATER
HPD CONTROLLER
CONTROLLER CONTROLLER BUFFER
to DIGITAL (2)_CB31
DDCA_SDA 64
CONTROLLER
DDCB_SDA 62
BKP1005HS680-T
DDCC_SDA 60 HDMI DGND
L37 R226
+5.5V
DDCD_SDA 58
5 6 7 8 R224 2.2

R223
AV 7 AV 6 AV 5 AV 4 AV 3 AV 2 AV 1

0X4
EP_SCK 68 36 TXA_DDC_SCL no_use
HDCP HDCP HDCP 4 3 2 1
EP_MISO 67 35 TXA_DDC_SDA
EP_MOSI 66 EEPROM ENGINE ENGINE
TX DDC
CONTROL 34 TXB_DDC_SCL
(1 BD/DVD) CB9

2 EP_CS
SPDIF_IN*
69

7
33 TXB_DDC_SDA
24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
502231-2400
WY78680
RXA_ARC 96 AUDIO
CB7
DC1R019JAXR190
HDMI IN-7 CB6
DC1R019JAXR190
HDMI IN-6 CB5
DC1R019JAXR190
HDMI IN-5 CB4
DC1R019JAXR190
HDMI IN-4 CB3
DC1R019JAXR190
HDMI IN-3 CB2
DC1R019JAXR190
HDMI IN-2 CB1
DC1R019JAXR190
HDMI IN-1
47,48
RXB_ARC 95 RETURN TXA_0±
50,51
RXC_ARC 94 CHANNEL HDMI TX TXA_1±
52,53
RXD_ARC 93
TXA_2± CB8

10

11
12
13

14
15
16

17
18
19

20
21
22
22FMN-BMT-A-TFT

1
2
3

4
5

6
7
8

9
121,122 25,26 FG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 FG FG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 FG FG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 FG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 FG FG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 FG FG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 FG FG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 FG
RXA_0± TXB_0± no_use
124,125
RXA_1± EQUALIZER SAMPLER 28,29

FR_SCL
SCL
SDA

HPD
4 Data2+

4 Data1+

4 DataC+
Sheild

3 Data2-

3 Data1-

3 Data0-

3 DataC-

FR_SDA
HDMI TX TXB_1±

Sheild1

CEC

+Vcc
+5VPower
4 Data0+
Sheild2

Sheild0

SheildC

F_HEQ_CE
126,127 30,31
RXA_2±

SCL

SDA
GND

HPD

SCL

SDA

GND

HPD

SCL

SDA
GND

HPD

SCL
SDA
GND

HPD

SCL

SDA

GND

HPD

SCL

SDA

GND

HPD

SCL
SDA

GND

HPD
CEC

CEC

CEC

CEC

CEC

CEC

CEC
TXB_2±

Data2+

Data2-
Data1+

Data1-

Data0+

Data0-

DataC-

Data2+

Data2-

Data1+
DataC+

Data2+

Data2-

Data1+

Data1-

Data0+

Data0-

DataC+

DataC-

Data2+

Data2-
Data1+

Data1-
Data0+

Data0-
DataC+

DataC-

Data1-

Data0+

Data0-

DataC+

DataC-

Data2+

Data2-

Data1+

Data1-
Data0+

Data0-

DataC+

DataC-

Data2+

Data2-
Data1+

Data1-
Data0+

Data0-

DataC+

DataC-

Data2+

Data2-

Data1+

Data0+

Data0-
DataC+

DataC-
Data1-
Sheild2

Sheild1

Sheild0

SheildC

Sheild2

Sheild1

Sheild0

SheildC

Sheild2

Sheild1

Sheild0

SheildC

Sheild2

Sheild1

Sheild0

SheildC

Sheild2

Sheild1

Sheild0

SheildC

Sheild2

Sheild1

Sheild0

SheildC

Sheild2

Sheild1

Sheild0

SheildC
Reserved

+5VPower

Reserved

+5VPower

Reserved

+5VPower

Reserved

+5VPower

Reserved

+5VPower

Reserved

+5VPower

+5VPower
Reserved
110,111 44,45 DGND DGND DGND DGND DGND DGND DGND DGND
RXB_0± XpressView TXA_C±
113,114 4:2 PLLs 22,23
RXB_1± EQUALIZER SAMPLER Fast TXB_C±

EXC24CH500U
115,116 Crossmux
RXB_2± Switching

L31

L32

L33

L34

0
0

0
0

0
0
100,101
RXC_0± TP1 TP4 TP10 TP12 TP18 TP20 TP27
103,104

R200

R202
R203
R204

R208
R209
RXC_1± EQUALIZER SAMPLER
105,106

1
2

2
1
2

1
RXC_2± AUDIO
TXA_ARC+ 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 +Vf
RXD_0± 84,85 RETURN

R207
TXA_HPD_ARC-

D12

D15

D18

D21
RCLAMP0584J

RCLAMP0584J

RCLAMP0584J

RCLAMP0584J

RCLAMP0584J

RCLAMP0584J

RCLAMP0584J
D3

D6

D9

L35

L36
CHANNEL

0
87,88
RXD_1± EQUALIZER SAMPLER DGND DGND DGND DGND DGND DGND 4.8

BKP1005HS680-T
DGND 6 7 8 9 6 7 8 9 6 7 8 9 6 7 8 9 DGND 6 7 8 9 6 7 8 9 6 7 8 9
RXD_2±
89,90 + HOT PLUG

RCLAMP0584J

RCLAMP0584J

RCLAMP0584J

RCLAMP0584J

RCLAMP0584J

RCLAMP0584J

RCLAMP0584J

RCLAMP0584J

RCLAMP0584J

RCLAMP0584J

RCLAMP0584J
RCLAMP0584J

RCLAMP0584J

RCLAMP0584J

0.1/10(BJ)
DETECT 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1
119,120 AUDIO

D11

D14

D17

D20
DGND

R109

R153

R173

R192

C181
D8
D2

D5
R36

R72

R87

D10

D13

D16

D19
RXA_C±

BKP1005HS680-T
D1

D4

D7
TP2 TP5 TP11 TP13 TP19 TP21 TP30

R107

R114

R149

R162

R171

R177

R189

R197
1K

1K

1K

1K

1K

1K

1K
R30

R45

R70

R76

R85

R98
INSERTION

10K

10K

10K

10K

10K

10K

10K
108,109

10

10

10

10

10

10

10
RXB_C± CONTROL 7 SPDIF_OUT* 6 7 8 9 6 7 8 9 6 7 8 9 6 7 8 9 6 7 8 9 6 7 8 9 6 7 8 9 6 7 8 9 6 7 8 9 6 7 8 9 6 7 8 9 6 7 8 9 6 7 8 9 6 7 8 9

22
22

22

22

22
22

22
22

22

22

22
22

22
22
98,99 PLLs INTERNAL R210
RXC_C± INTERFACE Q2 Q4 Q6 Q8 Q10 Q12 Q16

TMDS

TMDS

TMDS

TMDS

TMDS

TMDS

TMDS
CLOCK
I2C

R110

R154

R174

R193
82,83 R40 R75 R97 R113 R160 R176 R196

R37

R73

R88
RXD_C± 100K

100K

100K

100K

R103

100K

R144

100K

R168

100K

R185

100K
R25

R65

R82

R102

R143

R167

R184
R24

R64

R81

R169
R68
47K

47K
1K 1K 1K 1K 1K 1K 1K DGND

R206
47K
C4081UBTLR C4081UBTLR C4081UBTLR C4081UBTLR C4081UBTLR C4081UBTLR C4081UBTLR

R105

R147

R187
R28

R83
no_use

no_use

no_use

no_use

no_use

no_use

no_use
47K

47K

47K

47K

47K
9 14 12 13 7 6 5 4 3 2 DGND DGND DGND DGND DGND DGND DGND

R108

R151

R172

R191
3

R32

R71

R86
CLK_IN

CS
SDA
SCL

LRCLK_IN*
SCLK_IN

IS20_IN
I2S1_IN
I2S2_IN
I2S3_IN

R38 R74 R96 R112 R159 R175 R194

R170
R69
47K

47K

R205
10K 10K 10K 10K 10K 10K 10K

47K
Q1 Q3 Q5 Q7 Q9 Q11 Q15

R106

R148

R188
R29

R84
47K

47K

47K

47K

47K
C4081UBTLR C4081UBTLR C4081UBTLR C4081UBTLR C4081UBTLR C4081UBTLR C4081UBTLR R211
DGND DGND DGND DGND DGND DGND DGND
47K
R212 +3.3H
* Signals SPDIF_IN, SPDIF_OUT and LRCLK_IN are on a shared pin SPDIF_IN/OUT/LRCLK_IN
47K

IN6_B_5VPWR

IN2_B_5VPWR
IN5_C_5VPWR

IN4_D_5VPWR

IN1_C_5VPWR
IN5_C_SCL

IN4_D_SCL

IN1_C_SCL
105

IN7_A_5VPWR

105

105

105

105

IN3_A_5VPWR

105

105

100
IN5_C_SDA

IN4_D_SDA

IN1_C_SDA
IN6_B_SCL

IN6_B_SDA

IN2_B_SCL

IN2_B_SDA

FR_D_5VPWR
IN7_A_SCL

IN7_A_HPD

IN6_B_HPD

IN3_A_SCL

IN3_A_HPD

IN2_B_HPD

FR_D_SCL
FR_D_SDA
IN7_A_SDA

IN5_C_HPD

IN4_D_HPD

IN3_A_SDA

IN1_C_HPD

FR_D_HPD
IC3, 4: ADV7619KSVZ
Dual port, Xpressview, 3 GHz HDMI receiver
VIDEO OUTPUT FORMATTER

XTALP 115 80-91

DPLL 300MHz VIDEO PATH P0 TO P11 +1.8H +1.8H
XTALN 116 66-76,78 BKP1005HS680-T L14 BKP1005HS680-T L28
P12 TO P23 +3.3H BKP1005HS680-T +3.3H BKP1005HS680-T
48-51,54-61

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)
0.01/16(B)

0.01/16(B)

0.1/10(BJ)

0.1/10(BJ)

0.01/16(B)

0.01/16(B)

0.1/10(BJ)

0.1/10(BJ)
SCL P24 TO P35 L4 L18

1000P(B)

1000P(B)
110

10/6.3

10/6.3
C150

C157

C161

C166
C71

C81

C85

C88
0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)
35-39,41-47

C152

C156

C169
C74

C79

C91

C104
1000P(B)

1000P(B)
CONTROL

10/6.3

10/6.3
P36 TO P47

C14

C22

C25
C100
SDA 109

C17

C112
C15

C29

C98

C103

C106

C110
C20

C23

C27
INTERFACE

RXC_1-

RXC_0+

RXC_0-

RXC_1-

RXC_0+

RXC_0-
RXC_1+

RXC_1+
RXA_2+

RXA_2-

RXA_1+

RXA_1-

RXA_0+

RXA_0-

RXA_C+

RXA_C-

RXB_2+

RXB_2-

RXB_1+

RXB_1-

RXB_0+

RXB_0-
RXB_C+
RXB_C-

RXC_2+

RXC_2-

RXA_2+
RXA_2-
RXA_1+

RXA_1-

RXA_0+

RXA_0-
RXA_C+
RXA_C-

RXB_2+

RXB_2-
RXB_1+
RXB_1-

RXB_0+
RXB_0-

RXB_C+
RXB_C-

RXC_2+
RXC_2-
CS 113 62 LLC

RXC_C+

RXC_C-

RXC_C+
RXC_C-
I2C

TVDD

TVDD
CVDD

CVDD
TVDD

CVDD
DVDD

TVDD

CVDD

TVDD

CVDD
DVDD

TVDD

CVDD
DGND

DGND
CVDD

CVDD
CEC
CEC 118 BACK-END 94 HS

DGND

DGND
CONTROLLER
COLOR 95 VS/FIELD/ALSB
RESET RESET

103

102

101
100

103
102

101
100
128

104

128

104
HSW_N_RST RXA_ARC HSW_N_RST RXA_ARC

127
126

125
124

123

122
121

120

119

118

117
116

115

114

113

112
111

110
109

108

107
106

105

127

126
125
124

123
122
121
120

119
118

117
116
115

114
113
112

111
110

109
108
107

106
105
RXA_5V 126 SPACE
4

99

98

97

99
98
97
65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96

65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96
93 DE TP6 TP23

1
122
5V DETECT CONTROL AND DATA CONVERSION 12S3_IN 12S3_IN
RXB_5V RXB_ARC RXB_ARC

DGND

DGND
AND HDP TP7 TP24

2
HPA_A/INT2* 125
CONTROLLER R22 12S2_IN RXC_ARC R126 12S2_IN RXC_ARC
TP8 TP25

3
HPA_B 121
INTERRUPT 111 INT1 12S1_IN RXD_ARC 12S1_IN RXD_ARC
CONTROLLER +3.3H TP9 +3.3H TP26

4
DDCA_SDA 124
EDID HDMI (INT1, INT2) INT2* 12S0_IN DVDD 12S0_IN DVDD
DDCA_SCL 123

HSW2

5
REPEATER PROCESSOR R16 10K SCLK_IN R119 10K SCLK_IN
DDCB_SDA 120 HDCP COMPONENT 10KX4 CVDD 10KX4 CVDD
CONTROLLER
HSW1

6
R120
4.7K

R117

4.7K
KEYS
R12

DDCB_SCL 119 PROCESSOR R17

AUDIO OUTPUT FORMATTER

10K SPDIF_IN/OUT/LRCLK_IN RXD_2+ 10K SPDIF_IN/OUT/LRCLK_IN RXD_2+

7
A
101 AP1/I2S_TDM
DATA HSW2_N_INT INT1 RXD_2- HSW1_N_INT INT1 RXD_2-
B 102 AP2

8
PREPROCESSOR
FAST SWITCHING

TP32 CLK_IN TP33 CLK_IN

HDMI SWITCHER HDMI SWITCHER

3,4 HSW2_27MHZ RXD_1+ HSW1_27MHZ RXD_1+
RXA_C± HDCP AND COLOR C 103 AP3

9
PLLs
Xpressview

20,21 CEC CEC

RXB_C± ENGINE SPACE 104 AP4 R21 RXD_1- R125 RXD_1-

32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
CONVERSION +3.3H +3.3H no_use +3.3H no_use
DVDDIO DVDDIO
6,7 PACKET/ 106 AP5 TVDD
HSW_N_CS=Low TVDD
RXA_0± INFOFRAME 105 SCLK/INT2* HDMI_SDA R18 22 SDA HSW_N_CS=High RXD_0+ HDMI_SDA R121 22 SDA RXD_0+
9,10
I2C:0xB0
R222

4.7K

RXA_1± EQUALIZER SAMPLER MEMORY MUTE

RXA_2± 12,13 PACKET 107 MCLK/INT2*
HDMI_SCL R19 22 SCL
I2C:0xB0 IC2 RXD_0- HDMI_SCL R122 22 SCL IC1 RXD_0-
PROCESSOR R15 CS ADV7630KSVZ RXD_C+ HSW_N_CS CS ADV7630KSVZ RXD_C+
23,24 AUDIO 100 AP0 Q19
RXB_0± PROCESSOR 0 DVDD DVDD
26,27
EQUALIZER RXD_C- RXD_C-
RXB_1± SAMPLER
29,30 TXB_PVDD +1.8HCPLL1 TXB_PVDD
RXB_2± G CVDD G CVDD
+1.8HCPLL2 C24 C107
L5 TXB_PLVDD_N C26 DVDD L19 C111 C109 TXB_PLVDD_N DVDD
C28 C18 C21 DGND C102 C105 DGND
DTC014EUBTL BKP1005HS680-T TP35TXVDD_3V3 SYS_3P3V BKP1005HS680-T BKP1005HS680-T TXVDD_3V3
TP37 SYS_3P3V BKP1005HS680-T
* INT2 can be made available on one of these pins: HPA_A/INT2, MCLK/INT2, OR SCLK/INT2. DGND 10/6.3 10/6.3
L38 L40
TXB_PLVDD_Q
No replacement part available. TXB_PLVDD_Q
No replacement part available.

0.1/10(BJ)

0.1/10(BJ)
HSW_N_CS DGND HPA_A IN7_A_HPD +3.3H DGND HPA_A IN3_A_HPD +3.3H

1000P(B)

1000P(B)
0.1/10(BJ) 0.1/10(BJ)

C184

C189
0.1/10(BJ) 0.01/16(B) 0.1/10(BJ) 0.01/16(B)

C108

C188
TXB_HPD RXA_5V IN7_A_5VPWR TXB_HPD RXA_5V IN3_A_5VPWR
+3.3H 1000P(B) 1000P(B)
R13 TX_AVDD
サービス部品供給なし HPA_B IN6_B_HPD
+3.3H
R118 TX_AVDD
サービス部品供給なし HPA_B IN2_B_HPD

DGND

DGND
5 4.7K
TXB_C-

TXB_C+
RXB_5V IN6_B_5VPWR
4.7K TXB_C-

TXB_C+
RXB_5V IN2_B_5VPWR

TX_AVDD 3.3V: 190mA

HPA_C IN5_C_HPD
TX_AVDD
3.3V: 190mA HPA_C IN1_C_HPD

RXC_5V IN5_C_5VPWR RXC_5V IN1_C_5VPWR

TX_2+ TXB_0- 1.8V: 470mA HPA_D IN4_D_HPD TX_2+ TXB_0-
1.8V: 470mA HPA_D FR_D_HPD
TX_2- TXB_0+ TX_2- TXB_0+
RXD_5V IN4_D_5VPWR RXD_5V FR_D_5VPWR
TX_AVDD DVDDIO,TVDD:3.3V TX_AVDD DVDDIO,TVDD:3.3V
IC9, 10, 12: RP130Q181D-TR-F REG_1P8V REG_1P8V

0.1/10(BJ)

0.1/10(BJ)
DVDD,PVDD,CVDD:1.8V DVDD,PVDD,CVDD:1.8V

0.01/16(B)

0.01/16(B)
TX_1+ TXB_1- DGND TX_1+ TXB_1- DGND
EP_CS EP_CS

C148
Voltage regulator

C66

C147
C63
TX_1- TXB_1+ EP_SCK TX_1- TXB_1+ EP_SCK

/CS

GND

/WP

/CS
GND

/WP
SO

SO
TX_0+ TXB_2- EP_MISO TX_0+ TXB_2- EP_MISO
DGND DGND
TX_0- TXB_2+ 4 3 2 1 TX_0- TXB_2+ 4 3 2 1

R181
R79
EP_MOSI EP_MOSI

R182
IC7 TXA(B) Main Map 0xFE[0]=1 IC8

R80
TX_AVDD TX_AVDD TX_0-/+,1-/+,2-/+
REG_3P3V 5 6 7 8 REG_3P3V 5 6 7 8
VDD 4 3 VOUT

SI

SI
58

59

60
61

62

63

64

58
59

60
61

62
63
64
33

34

35
36

37

38

39

40
41

42

43

44
45

46

47

48

49
50

51
52

53

54
55

56

57

33

34
35
36

37
38

39
40
41

42
43

44
45
46

47
48
49

50
51

52
53
54

55
56

57
SCK

SCK
0.1/10(BJ)

0.1/10(BJ)
/HOLD

/HOLD
0.01/16(B)

VCC
VCC
0.01/16(B)

R179
3.9K
C142

C144
C59
C58

3.9K
TXA_HEAC-

TXA_HEAC-
R77
DVDD

DVDD
R_EXT

R_EXT
TXA_HPD_HEAC-

TXA_HPD_HEAC-
TXA_C-

TXA_C+

TXA_0-
TXA_0+

TXA_1-

TXA_1+
TXA_2-

TXA_2+

TXA_C-
TXA_C+

TXA_0-
TXA_0+

TXA_1-

TXA_1+
TXA_2-
TXA_2+
TX_AVDD

TX_AVDD

TX_AVDD

TX_AVDD

TX_AVDD

TX_AVDD

TX_AVDD

TX_AVDD
TXA_PVDD

DDCD_SCL
DDCD_SDA
DDCC_SCL

DDCC_SDA

DDCB_SCL

DDCB_SDA

DDCA_SCL
DDCA_SDA

TXA_PVDD

DDCD_SCL
DDCD_SDA

DDCC_SCL
DDCC_SDA
DDCB_SCL

DDCB_SDA
DDCA_SCL

DDCA_SDA
R78 R180
TXVDD_3V3

TP38TXVDD_3V3
TXB_DDC_SDA

TXB_DDC_SCL

TXA_DDC_SDA

TXA_DDC_SCL

TXA_PLVDD_N

TXA_PLVDD_Q

TXB_DDC_SDA
TXB_DDC_SCL
TXA_DDC_SDA

TXA_DDC_SCL

TXA_PLVDD_N

TXA_PLVDD_Q
C60 C145

no_use DGND DGND no_use DGND

DGND +1.8H +1.8H
25LC040A-I-ST( ) BKP1005HS680-T 25LC040A-I-ST( ) BKP1005HS680-T
L15 L29

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)
0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)
TP36

1000P(B)

1000P(B)
BKP1005HS680-T BKP1005HS680-T

10/6.3

10/6.3
C153

C158

C164

C167

C170

C172

C176
C76

C82

C86

C94
C89

C92

C96
Vref
0.01/16(B)

0.01/16(B)
L3 L17
+3.3H +3.3H
0.1/10(BJ)

0.1/10(BJ)
10/6.3

10/6.3
22

22

22

22
R62
TX_2+
TX_2-

TX_1+

TX_1-
TX_0+
TX_0-

DGND

C101

TX_2+
TX_2-

TX_1+
TX_1-

TX_0+
TX_0-

DGND
no_use
Current Limit
22

22

22

22
C16

C19

C99
0.1/10(BJ)

0.1/10(BJ)
C131

R165
C31

no_use

IN4_D_SCL

IN4_D_SDA
IN5_C_SCL

IN5_C_SDA

IN6_B_SCL

IN6_B_SDA

IN7_A_SCL

IN7_A_SDA

IN1_C_SCL
IN1_C_SDA

IN2_B_SCL
IN2_B_SDA

IN3_A_SCL
IN3_A_SDA
FR_D_SCL
FR_D_SDA
R163
6
R54

CE 1 2 GND BKP1005HS680-T BKP1005HS680-T

470

470
R145
R146

R150
R152

C132
R26

R27

R31

R33

C32

L16 L30
DGND

DGND
0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)
+1.8H +1.8H

C133
C33

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)
DGND

4.7K

DGND
R166
4.7K
1000P(B)

1000P(B)
R63

10/6.3

10/6.3
C151

C155

C159

C165

C168

C171

C173

C177
1000P(B)

1000P(B)
C72

C77

C83

C87

C90

C93

C95

C97
C30 C34

C134
DGND

DGND
0.1/10(BJ)

0.1/10(BJ)
DGND

DGND
C115
Pin No. Symbol Description
+3.3H
10/6.3

10/6.3
1 CE Chip Enable ("H" Active) +3.3H
BKP1005HS680-T
L8

BKP1005HS680-T
2 GND Ground Pin
DGND

+1.8HCPLL1

L22

DGND
HSW2B_DSDA

HSW2B_DSCL

HSW2A_DSDA

HSW2A_DSCL

HSW1B_DSDA
HSW1B_DSCL
3 VOUT Output Pin
+1.8HCPLL2

4 VDD Input Pin

R139 R155 4.7K

4.7K
+3.3H R156 4.7K
To 005.sht
R140 +3.3H (HDMI_Tx)
4.7K

CEC

to DIGITAL 5/10

no_use
R201
BKP1005HS680-T BKP1005HS680-T
HSW2B_DSDA
HSW2B_DSCL
HSW1B_DSDA
HSW1B_DSCL

+1.8H +1.8H +3.3H

HSW2A_DSDA
HSW2A_DSCL
L2 L13 RX_CEC
0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)
0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)
TP39 IC5
7
1000P(B)

1000P(B)
TP41
10/6.3

10/6.3

0.1/10(BJ)
C10

C12

C62

C65

C68

C70

C75

C80
V+ 9
C2

C4

C6

C8

TP40
IC5 14 10 8

C174
7 FHDMI_SDA
X5404A0
DGND

DGND

V-
SN74LVC08APWR FHDMI_SCL
+3.3H
+3.3H BKP1005HS680-T DGND DGND +3.3H BKP1005HS680-T DGND DGND
DGND DGND HRX1_N_INT DGND DGND F_HEQ_CE
L1 L12
RXB_2+
RXB_2-

RXB_1+
RXB_1-

RXB_0+

RXB_0-

RXB_C+

RXA_1+

RXA_1-

RXA_C-

RXB_2+
RXB_2-

RXB_1+
RXB_1-

RXB_0+
RXB_0-

RXB_C+

RXA_1+
RXA_1-

RXA_C-
IC5
RXB_C-

RXA_2+
RXA_2-

RXA_0+

RXA_0-

RXA_C+

RXB_C-

RXA_2+

RXA_2-

RXA_0+
RXA_0-

RXA_C+
0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)
0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)
IC5 HSW2_N_INT
1000P(B)

1000P(B)
10/6.3

10/6.3
CVDD

TVDD

TVDD

TVDD

CVDD

CVDD

TVDD

TVDD

TVDD

CVDD
12

R164

4.7K
R221
C64
CVDD

DVDD

CVDD

TVDD

TVDD

TVDD

CVDD

DVDD

CVDD

TVDD

TVDD

TVDD
R220
C3

GND

GND
C11

C13

C61

C78

C84
1 3 HRX_N_INT
13 11
C1

GND

GND

GND

GND
C67

C69

C73
HSW1_N_INT HSW_N_INT
C5

C7

C9

NC

NC

NC

NC
2 68 68
HRX2_N_INT HSW_N_RST SN74LVC08APWR
NC 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 NC +3.3H NC 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 NC SN74LVC08APWR HSW_N_RST
DGND

DGND

33 128 33 128 +3.3H HSW_N_CS

DVDD NC DVDD NC HSW_N_CS
34 127 34 127 HRX1_N_MT HSW1_27MHZ
R215

4.7K

R216

4.7K
HRX_D[47] A47 RXA_5V R39 0 HRX_Z_D[47] A47 RXA_5V R127 0 IC5 HSW1_27MHZ
35 126 +3.3H 35 126 +3.3H R219 HSW2_27MHZ
R1 R89 TP14 4 HAU_N_INT HSW2_27MHZ
6
HRX_D[46] A46 HPA_A HRX1_N_MT HRX_Z_D[46] A46
HRX2(ZONE) HPA_A
5 +3.3H

470P(B)
36 125 36 125 68 HRX2_N_MT HDMI_SCL

R199

10K
R57 TP15

C180
HRX_D[45] A45
HRX1(MAIN) DDCA_SDA 4.7K
+3.3H
HRX_Z_D[45] A45 DDCA_SDA SN74LVC08APWR HRX2_N_MT R225 HDMI_SDA

R186

R190
37 124 37 124 +3.3H

2.2K

2.2K
HRX_D[44] 33X4 A44 DDCA_SCL R58 4.7K HRX_Z_D[44] 33X4 A44 DDCA_SCL TP16 4.7K
38 123 38 123
A43 RXB_5V R41 0 A43 RXB_5V R128 0 DGND
HDMI_SCL
39 122 39 122 HDMI_SCL
HRX_D[43] DVDDIO HPA_B TP3 R217 no_use HRX_Z_D[43] DVDDIO HPA_B TP17 R218 no_use +3.3H
HDMI_SDA
40 121 40 121 HDMI_SDA
HRX_D[42] R2 A42 DDCB_SDA R55 4.7K HRX_Z_D[42] R90 A42 DDCB_SDA
41 120 +3.3H 41 120 HRX1_N_RST
HRX_D[41] A41 DDCB_SCL R56 4.7K D22 +3.3H HRX_Z_D[41] A41 DDCB_SCL HRX1_N_RST
R59
42 119 42 119 HRX2_N_RST
33X4 no_use 33X4 R129 no_use HRX2_N_RST
HRX_D[40]

HRX_D[39]
A40
A39
43
HDMI RECEIVER 118
CEC

DVDD
R52 C45
DGND
no_use RX_CEC HRX_Z_D[40]

HRX_Z_D[39]
A40
A39
43
HDMI RECEIVER 118
CEC

DVDD
R142
+3.3H
C124
DGND
HRX_N_INT
HRX_N_INT
28.63636MHZ

28.63636MHZ
44 117 150 44 117 150
2

2
no_use

no_use

1
IC5: SN74LVC08APWR

0.1/10(BJ)
10P(CH) 10P(CH) HRX1_N_MT

R138
0.1/10(BJ)

R3 A38 R91 A38

XL1
R43

XL2
HRX_D[38] XTALN HRX_Z_D[38] XTALN HRX1_N_MT
1000P(B)

1000P(B)
45 116 DGND +3.3H 45 116 DGND
3

3
4
C46 C125

10/6.3
A37 A37 HRX2_N_MT

C135

C183
8 Quadruple 2-input positive-AND gate
10/6.3

HRX_D[37] XTALP HRX_Z_D[37] XTALP

C182

C129
C50

C52

+1.8HRPLL HRX2_N_MT
46 115 46 115
HRX_D[36] 33X4 A36 PVDD 10P(CH) L10 HRX_Z_D[36] 33X4 A36 PVDD 10P(CH) L23 +1.8HRPLL HAU_N_INT
47 DGND 114 47 DGND 114 HAU_N_INT
4.7K
R67

HRX_D[35] A35 CS R42 BKP1005HS680-T HRX_Z_D[35] A35 CS R131 BKP1005HS680-T

DGND

no_use

no_use
48 113 DGND 48 113

C154

C160
R4 ADV7619KSVZ 4.7K R92 ADV7619KSVZ 4.7K HDMI_PON
HRX_D[34] A34 RESETB R60 0 HRX1_N_RST HRX_Z_D[34] A34 RESETB R158 0 HRX2_N_RST
49 112 49 112
HRX_D[33] A33 IC3 INT R46 0 HRX1_N_INT HRX_Z_D[33] A33 IC4 INT R132 0 HRX2_N_INT
1A 1 14 Vcc
HRX_D[32] 33X4 A32
50 111
SCL R47 22 HDMI_SCL HRX_Z_D[32] 33X4 A32
50 111
SCL R133 22 HDMI_SCL
+1.8H +3.3H To 006.sht
DGND
51
3.3V: 101mA 110 51
3.3V: 101mA 110
( -com)

TP22

TP29
1B 2 13 4B DVDDIO SDA R48 22 HDMI_SDA DVDDIO SDA R134 22 HDMI_SDA 1.9 +1.8D 3.3 +3.3D
52 109 52 109
DVDD
53
1.8V: 475mA 108
DVDD 470P(B)
C49 R61 10K DVDD
53
1.8V: 475mA 108
DVDD 470P(B)
C128 R161 10K
to DIGITAL 6/10
1Y 3 12 4A HRX_D[31] A31 MCLK R49 68 MCLK DGND RT_MCLK HRX_Z_D[31] A31 MCLK R135 100 MCLK DGND RTZ_MCLK
54 107 54 107
HRX_D[30] R5 A30 DVDDIO,TVDD:3.3V AP5 R50 100 LRCLK_DSD2B RT_WS/D2B HRX_Z_D[30] R93 A30 DVDDIO,TVDD:3.3V AP5 R136 100 LRCLK_DSD2B RTZ_WS/D2B 6 5 4 Q18
6 5 4 Q14

RAL035P01
2A 4 11 4Y 55 106 55 106

R195
DVDD,PVDD,CVDD:1.8V DVDD,PVDD,CVDD:1.8V 3 2

RAL035P01

680
A29 SCLK A29 R137 100 SCLK

R178
HRX_D[29] SCLK R51 100 RT_SCK/DCLK HRX_Z_D[29] SCLK RTZ_SCK/DCLK 3 2

680

Q17
1000P(B)
C143
1000P(B)

Q13
56 105 56 105

C162
33X4 A28 SD3_DSD2A 33X4 A28 SD3_DSD2A

0.01/16(B)
HRX_D[28] AP4 RT_SD3/D2A HRX_Z_D[28] AP4 RTZ_SD3/D2A

0.01/16(B)
2B 5 10 3B 57 104 57 104 1 2 3

C178

R198
A27
No replacement part available. SD2_DSD1B A27
No replacement part available. SD2_DSD1B 1 2 3

C146

100K
HRX_D[27] AP3 RT_SD2/D1B HRX_Z_D[27] AP3 RTZ_SD2/D1B

R183
100K
58 103 58 103
HRX_D[26] R6 A26 AP2 R53 100X4 SD1_DSD1A RT_SD1/D1A HRX_Z_D[26] R94 A26 AP2 R141 100X4 SD1_DSD1A RTZ_SD1/D1A
2Y 6 9 3A 59 102 59 102
HRX_D[25]
33X4
A25
60 サービス部品供給なし 101
AP1
R44
SD0_DSD0B

SPDIF_DSD0A
RT_SD0/D0B HRX_Z_D[25]
33X4
A25
60 サービス部品供給なし 101
AP1
R130
SD0_DSD0B

SPDIF_DSD0A
RTZ_SD0/D0B 1 DTA044EUBTL
1 DTA044EUBTL

GND 7 8 3Y HRX_D[24] A24 AP0 RT_SPDIF/D0A HRX_Z_D[24] A24 AP0 RTZ_SPDIF/D0A DGND
HRX_CLK R7 LLC
61 ALSB:H /L 100
NC
100 HRX_Z_CLK R95 LLC
61 ALSB:H /L 100
NC
100 DGND
62
I2C:0x9A/98 99 62
I2C:0x9A/98 99
220KX4

220KX4
R157

R214
220KX4

220KX4
0 33

R213
R66

DVDD NC DVDD NC
63 98 +3.3H 63 98 +3.3H
DVDD DVDD +3.3H +3.3H
NC NC +3.3H +1.8HCPLL2 +1.8HCPLL1
64 97 64 97 +1.8HRPLL
no_use

65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96

R123
R34

10K
DGND DGND TP31 1.8 TP34 1.8
DVDD

DVDD

TP28
9 1.8
DVDDIO

DVDDIO
A23
A22
A21

A20
A19
A18

A17
A16

A15

A14

A13

A12

A11
A10

A23
A22
A21
A20

A19
A18

A17
A16
A15

A14
A13

A12

A11
A10
DVDDIO

DVDDIO

DVDDIO

DVDDIO
VS/ALSB

VS/ALSB
A9

A8

A7
A6
A5

A4

A3
A2

A1

A0

DE
HS

NC

A9
A8
A7

A6
A5

A4
A3
A2

A1
A0

DE
HS

NC

VOUT

VOUT
VDD

VDD
VOUT
VDD
no_use
R124

RP130Q181D-TR-F

RP130Q181D-TR-F
R35
1.8K

RP130Q181D-TR-F

10/6.3

10/6.3
L9 L24 4 3 4 3

C175

C190
10/6.3

10/6.3

10/6.3
4 3

C149

C179

C191
IC10 IC12

10/6.3
BKP1005HS680-T BKP1005HS680-T

C163
+3.3H IC9 1 2 1
DGND DGND +3.3H 2
1 2

GND

GND
CE/CE

CE/CE
0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

0.1/10(BJ)

GND
CE/CE
1000P(B)

1000P(B)
10/6.3