Technical Notes

XLTN 2.1 STANDARD CONNECTION DETAILS

xlam.com.au I xlam.co.nz
 Technical Note 2.1 Standard Details V1

Use of This Technical Note

The information is provided for use in the design and specification of XLam manufactured Cross Laminated
Timber (CLT) only. The Technical Note is not intended as general information and guidance for all
manufactured Cross Laminate Timber (CLT). The Technical Note and information is specific to XLam CLT and
no warranty is given to the suitability and application of the information to other manufacturers CLT.

Summary
This Technical Note contains drawings of standard construction details for XLam manufactured Cross
Laminated Timber at ambient temperatures.

Application and Limitations

The sourcing and installation requirements of other products referred to in this document should be procured
from the respective manufacturer. Advice on overall building design issues including but not limited to
stability, loading, temporary stability during construction, fixings, waterproofing and overall fire and acoustic
performance should be considered separately on advice sought from suitably qualified professionals.

It is the responsibility of the user to ensure that the use of this Technical Note is appropriate and to exercise
professional judgement when using this document. Full responsibility for the design and compliance with
either the Building Code of Australia (BCA) or the New Zealand Building Code (NZBC) and all relevant
Australian and New Zealand Standards rests with the design professional specifying the product. XLam will not
accept any liability for the failure of any other elements of the building which have subsequent failure of an
XLam product.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
2
 Technical Note 2.1 Standard Details V1

Drawing Index

ABBREVIATIONS/SYMBOLS 5
TYPICAL DETAILS OVERVIEW 6-9

WALL TO CONCRETE CONNECTIONS

A1 XLam Wall to Concrete Slab Shear Connection 10
A2 XLam Wall to Concrete Slab Shear Connection 11
A3 XLam Wall to Concrete Slab Edge Shear Connection 12
A4 XLam Wall to Concrete Slab Shear Connection 13
A5 XLam Wall to Concrete Slab Shear Connection 14
A6 XLam Wall to Concrete Slab Shear Connection 15
A7 XLam Wall to Concrete Slab Shear Connection 16
A8 XLam Wall to Concrete Slab Hold Down Connection 17
A9 XLam Wall to Concrete Slab Hold Down Connection 8

FLOOR TO FLOOR CONNECTIONS

B1 XLam Floor to Floor Lap Joint 19
B2 XLam Floor to Floor Spline Joint 20

WALL TO FLOOR EDGE CONNECTIONS

C1 XLam Wall to Floor Connection (Platform Construction) 21
C2 XLam Wall to Floor Connection (Edge) 22
C3 XLam Wall to Floor Connection (Edge) 23
C4 XLam Wall to Floor Connection (Balloon Construction) 24
C5 XLam Floor to Concrete Wall Connection (Edge) 25
C6 XLam Wall to Floor Hold Down Connection (Edge) 26
C7 XLam Wall to Wall Hold Down Connection (Edge) 27

WALL TO MID FLOOR CONNECTIONS

D1 XLam Floor to Floor Half Lap Connection (Over Wall) 28
D2 XLam Floor to Wall Connection 29
D3 XLam Floor to Wall Connection 30
D4 XLam Floor to Wall Connection 31

WALL TO WALL CONNECTIONS

E1 XLam Wall to Wall Half Lap Connection 32
E2 XLam Wall to Wall Connection 33
E3 XLam Wall to Wall Connection 34
E4 XLam Wall to Wall Connection 35
E5 XLam Wall to Wall Connection 36

AIRSTAIRS CONNECTIONS
F1 XLam Airstair to Concrete Landing Connection 37
F2 XLam Airstair to XLam Landing Bottom Connection 38
F3 XLam Airstair to XLam Landing Sliding Bottom Connection 39
F4 XLam Airstair to XLam Landing Plastic Sliding Connection 40
F5 XLam Airstair to XLam Landing Sloped Seating Connection 41
F6 XLam Airstair to XLam Landing Lap Joint Seating Connection 42
F7 XLam Airstair to Corbel Connection 43

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
3
 Technical Note 2.1 Standard Details V1

ROOF CONNECTIONS
G1 XLam Roof to Roof Connection (Ridge Beam) 44
G2 XLam Roof to Roof Connection 45
G3 XLam Wall to Roof Connection 46
G4 XLam Wall to Roof Connection 47

LINTEL CONNECTION
H1 XLam Lintel to Wall Connection 48

SET DOWN CONNECTIONS

J1 XLam Floor to Floor Set-Down (Over Wall) 49
J2 XLam Floor to Floor Set-Down 50
J3 XLam Floor to Floor Set-Down 51
J4 XLam Floor to Floor Corbel Set-Down (Over Wall) 52

STEEL CONNECTIONS
K1 XLam Floor to Steel Beam Connection 53
K2 XLam Floor to Floor Connection (Lap Joint Over Steel Beam) 54
K3 XLam Floor to RHS Beam Connection 55
K4 XLam Floor to Floor Connection (Spline Joint Over Steel Beam) 56
K5 XLam Floor to Steel Beam Connection 57

FIN-PLATE CONNECTIONS
L1 XLam Wall to Concrete Fin Plate Connection 58
L2 XLam Wall to Concrete Fin Plate Connection 59
L3 XLam Wall to Concrete Fin Plate Connection 60
L4 XLam Wall to Wall Fin Plate Connection 61

SHERPA CONNECTIONS
M1 XLam Wall to Wall Sherpa Connection 62
M2 XLam Floor to Wall Sherpa Connection 63
M3 XLam Floor to Floor Sherpa Connection 64

GLULAM CONNECTIONS
N1 Glulam Beam to Column Connection (Screws) 65
N2 Glulam Beam to Column Connection (Epoxied Rods) 66
N3 Glulam Beam to Beam Alumidi Connection 67
N4 Glulam Beam to XLam Floor Steel Plate Connection 68
N5 Glulam Beam to Concrete Slab Steel Base Connection 69

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
4
 Technical Note 2.1 Standard Details V1

Abbreviations/Symbols
AT. Airstair Thickness
BE. Bracket Edge Distance
BH. Beam Height
BW. Beam Width
CH. Column Height
CRS. Centres
CW. Column Width
D. Distance
E. Edge Distance
EQ. Equal Distance
FE. Fixing Edge Distance
FL. Fixing Length
FT. Floor Thickness
H. Height
L. Length
LT. Landing Thickness
N. Nail Centers
PH. Plate Height
PTD. Partial Thread Distance
PTE. Partial Thread Edge Distance
PTL. Partial Thread Length
PW. Plate Width
RD. Rebate Depth
RT. Roof Thickness
SD. Spline Depth
SL. Seating Length
T. Thickness
THR. Airstair Throat Thickness
W. Width
WHD. Washer Head Distance
WHE. Washer Head Edge Distance
WHL. Washer Head Length
WT. Wall Thickness
Ø. Diameter

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
5
 Technical Note 2.1 Standard Details V1

A1 A2 A3 A4 A5
FLOOR CONNECTIONS
WALL TO CONCRETE

XLam Wall to Concrete XLam Wall to Concrete XLam Wall to Concrete XLam Wall to Concrete XLam Wall to Concrete
Slab Shear Connection Slab Shear Connection Slab Edge Shear Connection Slab Shear Connection Slab Shear Connection

A6 A7 A8 A9

XLam Wall to Concrete XLam Wall to Concrete XLam Wall to Concrete XLam Wall to Concrete
Slab Hold Down Connection Slab Shear Connection Slab Hold Down Connection Slab Hold Down Connection

B1 B2
FLOOR TO FLOOR
CONNECTIONS

XLam Floor to Floor XLam Floor to Floor

Lap Joint Spline Joint

C1 C2 C3 C4 C5
EDGE CONNECTIONS
WALL TO FLOOR

XLam Wall to Floor Connection XLam Wall to Floor XLam Wall to Floor XLam Wall to Floor Connection XLam Floor to Concrete
(Platform Construction) Connection (Edge) Connection (Edge) (Balloon Construction) Wall Connection (Edge)

C6 C7

XLam Wall to Floor Hold Down XLam Wall to Wall Hold Down
Connection (Edge) Connection (Edge)

OVERVIEW 1 OF 4

XLAM TYPICAL DETAILS date: 09/03/2021

TM
OVERVIEW DRW: TS - PR: JL
REV: A

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
6
 Technical Note 2.1 Standard Details V1

D1 D2 D3 D4
WALL TO MID-FLOOR
CONNECTIONS

XLam Floor to Floor Half Lap XLam Floor to Wall XLam Floor to Wall XLam Floor to Wall
Connection (Over Wall) Connection Connection Connection

E1 E2 E3 E4 E5
WALL TO WALL
CONNECTIONS

XLam Wall to Wall XLam Wall to Wall XLam Wall to Wall XLam Wall to Wall XLam Wall to Wall
Half Lap Connection Connection Connection Connection Connection

F1 F2 F3 F4 F5
CONNECTIONS

XLam Airstair to Concrete XLam Airstair to XLam XLam Airstair to XLam Landing XLam Airstair to XLam Landing XLam Airstair to XLam Landing
AIRSTAIR

Landing Connection Landing Bottom Connection Sliding Bottom Connection Plastic Sliding Connection Sloped Seating Connection

F6 F7

XLam Airstair to XLam Landing XLam Airstair to Corbel

Lap Joint Seating Connection Connection

G1 G2 G3 G4
CONNECTIONS
ROOF

XLam Roof to Roof XLam Roof to Roof XLam Wall to Roof XLam Wall to Roof
Connection (Ridge Beam) Connection Connection Connection

OVERVIEW 2 OF 4

XLAM TYPICAL DETAILS date: 09/03/2021

TM
OVERVIEW DRW: TS - PR: JL
REV: A

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
7
 Technical Note 2.1 Standard Details V1

H1
CONNECTION
LINTEL

XLam Lintel to Wall Connection

J1 J2 J3 J4
CONNECTIONS
SET-DOWN

XLam Floor to Floor XLam Floor to Floor XLam Floor to Floor XLam Floor to Floor
Set-Down (Over Wall) Set-Down Set-Down Corbel Set-Down (Over Wall)

K1 K2 K3 K4 K5
CONNECTIONS
STEEL

XLam Floor to Floor XLam Floor to Floor

XLam Floor to Steel Connection (Lap Joint XLam Floor to RHS Connection (Spline Joint XLam Floor to Steel
Beam Connection Over Steel Beam) Beam Connection Over Steel Beam) Beam Connection

L1 L2 L3 L4
CONNECTIONS
FIN-PLATE

XLam Wall to Concrete XLam Wall to Concrete XLam Wall to Concrete XLam Wall to Wall
Fin Plate Connection Fin Plate Connection Fin Plate Connection Fin Plate Connection

M1 M2 M3
CONNECTIONS
SHERPA

XLam Wall to Wall XLam Floor to Wall XLam Floor to Floor

Sherpa Connection Sherpa Connection Sherpa Connection

OVERVIEW 3 OF 4

XLAM TYPICAL DETAILS date: 09/03/2021

TM
OVERVIEW DRW: TS - PR: JL
REV: A

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
8
 Technical Note 2.1 Standard Details V1

N1 N2 N3 N4 N5
CONNECTIONS
GLULAM

Glulam Beam to Column Glulam Beam to Column Glulam Beam to Beam Glulam Beam to XLam Floor Glulam Beam to Concrete
Connection (Screws) Connection (Epoxied Rods) Alumidi Connection Steel Plate Connection Slab Steel Base Connection

OVERVIEW 4 OF 4

XLAM TYPICAL DETAILS date: 09/03/2021

TM
OVERVIEW DRW: TS - PR: JL
REV: A

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
9
 Technical Note 2.1 Standard Details V1

240
Bracket Dimensions are illustrative only and
specific bracket selection and dimensions are
brand and project design and specification

120
specific.

3
12
P Top view I Axo
XL TD1 1:15 XL TD1 nts

WT
MIN DISTANCE
BETWEEN BRACKETS MIN EDGE DISTANCE

XLAM WALL PANEL

FULLY THREADED
MASS TIMBER SCREW
MASS TIMBER BRACKET
D E
20mm TOLERANCE
TO BE SHIMMED
ANCHOR TO SUIT BRACKET AND DRY PACKED
20
L

DPC BETWEEN CLT

AND CONCRETE

MIN EMBEDMENT

E Front view S Right view

XL TD1 1:15 XL TD1 1:15

Drawing: XL TD 1
XLam Typical Details: A1 date: 09/03/2021
XLam Wall to Concrete Slab Shear Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
10
 Technical Note 2.1 Standard Details V1

95

Bracket Dimensions are illustrative only and

specific bracket selection and dimensions are
brand and project design and specification

170
specific.

0
11
P Top view I Axo
XL TD2 1:15 XL TD2 nts

MIN DISTANCE
WT
BETWEEN BRACKETS MIN EDGE DISTANCE

XLAM WALL PANEL

NAIL/SCREW FIXINGS
D E MASS TIMBER BRACKET TO SUIT BRACKET

20mm TOLERANCE
ANCHOR TO SUIT BRACKET TO BE SHIMMED
AND DRY PACKED
20
L

DPC BETWEEN CLT

AND CONCRETE
MIN EMBEDMENT

E Front view S Right view

XL TD2 1:15 XL TD2 1:15

Drawing: XL TD 2
XLam Typical Details: A2 date: 09/03/2021
XLam Wall to Concrete Slab Shear Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
11
 Technical Note 2.1 Standard Details V1

95 95

Bracket Dimensions are illustrative only and

specific bracket selection and dimensions are
brand and project design and specification
240

170
specific.

0
11
P Top view I Axo
XL TD3 1:15 XL TD3 nts

MIN DISTANCE WT
BETWEEN BRACKETS MIN EDGE DISTANCE

XLAM WALL PANEL

NAIL/SCREW FIXINGS
TO SUIT BRACKET

D E TENSION PLATE MASS TIMBER BRACKET

(IF REQUIRED)
20mm TOLERANCE
TO BE SHIMMED
AND DRY PACKED
20
L

ANCHOR TO SUIT BRACKET

DPC BETWEEN CLT

AND CONCRETE

MIN EMBEDMENT

E Front view S Right view

XL TD3 1:15 XL TD3 1:15

Drawing: XL TD 3
XLam Typical Details: A3 date: 09/03/2021
XLam Wall to Concrete Slab Edge Shear Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
12
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD4 1:15 XL TD4 nts

WT
MIN CENTERS
BETWEEN ANCHORS MIN EDGE DISTANCE

XLAM WALL PANEL

PARTIALLY THREADED
MASS TIMBER SCREW
D E
TIMBER BASE PLATE
20mm TOLERANCE
D E
TO BE SHIMMED
AND DRY PACKED
ANCHOR TO SUIT
20
L

DPC BETWEEN CLT

MIN EMBEDMENT AND CONCRETE

E Front view S Right view

XL TD4 1:15 XL TD4 1:15

Drawing: XL TD 4
XLam Typical Details: A4 date: 09/03/2021
XLam Wall to Concrete Slab Shear Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
13
 Technical Note 2.1 Standard Details V1

Bracket Dimensions are illustrative only and

specific bracket selection and dimensions are

75
brand and project design and specification
specific.
it
75 t o su
gth
Len

P Top view I Axo

XL TD5 1:15 XL TD5 nts

MIN CENTERS WT
BETWEEN ANCHORS MIN EDGE DISTANCE

XLAM WALL PANEL

BOLT, DOWEL OR SCREW

D E
MASS TIMBER T-PLATE
20mm TOLERANCE
D E TO BE SHIMMED
AND DRY PACKED
L

ANCHORS TO SUIT FIN PLATE

MIN EMBEDMENT
DPC BETWEEN CLT
AND CONCRETE

E Front view S Right view

XL TD5 1:15 XL TD5 1:15

Drawing: XL TD 5
XLam Typical Details: A5 date: 09/03/2021
XLam Wall to Concrete Slab Shear Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
14
 Technical Note 2.1 Standard Details V1

440
Bracket Dimensions are illustrative only and
specific bracket selection and dimensions are
brand and project design and specification
specific.

60 63
P Top view I Axo
XL TD6 1:15 XL TD6 nts

EDGE DISTANCE

WT

E FIXINGS TO
SUIT BRACKET XLAM WALL

MASS TIMBER BRACKET 20mm TOLERANCE

TO BE SHIMMED
AND DRY PACKED
ANCHOR TO
SUIT BRACKET CONCRETE SLAB
L

DPC BETWEEN CLT

AND CONCRETE
MIN EMBEDMENT

E Front view S Right view

XL TD6 1:15 XL TD6 1:15

Drawing: XL TD 6
XLam Typical Details: A6 date: 09/03/2021
XLam Wall to Concrete Slab Hold Down Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
15
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD7 1:15 XL TD7 nts

MIN CENTERS MIN CENTERS WT

BETWEEN NAILS BETWEEN ANCHORS MIN EDGE DISTANCE

XLAM WALL

20mm TOLERANCE
POLE PLATE
N TO BE SHIMMED
D E CONTINUOUS PLY AND DRY PACKED
ON OUTSIDE EDGE
W. NAILS TO SUIT CONCRETE SLAB
L

ANCHOR TO
SUIT BRACKET

MIN EMBEDMENT DPC BETWEEN CLT

AND CONCRETE

E Front view S Right view

XL TD7 1:15 XL TD7 1:15

Drawing: XL TD 7
XLam Typical Details: A7 date: 09/03/2021
XLam Wall to Concrete Slab Shear Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
16
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD8 1:15 XL TD8 nts

MIN CENTERS
BETWEEN ANCHORS MIN EDGE DISTANCE

WT
D D E
VARIED REBAR LENGTHS
TO EASE PANEL INSTALL XLAM WALL

BREATHER HOLES
20mm TOLERANCE
TO BE SHIMMED
AND DRY PACKED
SILICON BEAD AROUND
R.L

REBAR ON SLAB
CONCRETE SLAB
L

REBAR CAST IN CONCRETE

AND EPOXIED IN PANEL

DPC BETWEEN CLT

AND CONCRETE
MIN EMBEDMENT

E Front view S Right view

XL TD8 1:15 XL TD8 1:15

Drawing: XL TD 8
XLam Typical Details: A8 date: 09/03/2021
XLam Wall to Concrete Slab Hold Down Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
17
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD9 1:15 XL TD9 nts

EDGE DISTANCE

WT
E
POCKET

XLAM WALL
TO SUIT NUT & WASHER
100

NUT & WASHER 20mm TOLERANCE

TO SUIT TO BE SHIMMED
AND DRY PACKED
H

CONCRETE SLAB
20

THREADED ROD
L

50mm SQUARE WASHER

WITH NUTS ON 2 SIDES

MIN EMBEDMENT
DPC BETWEEN CLT
AND CONCRETE

E Front view S Right view

XL TD9 1:15 XL TD9 1:15

Drawing: XL TD 9
XLam Typical Details: A9 date: 09/03/2021
XLam Wall to Concrete Slab Hold Down Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
18
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD10 1:15 XL TD10 nts

MAX CENTERS
BETWEEN FIXINGS MIN EDGE DISTANCE
50mm MIN
#100mm MAX#

PARTIALLY THREADED
EQ MASS TIMBER SCREW
D E
EQ
EQ
FT
L

EQ

Ø
XLAM FLOOR PANEL

Ø = SCREW DIAMETER
MIN FIXING LENGTH
L > (T/2) + (4 x Ø)

E Front view S Right view

XL TD10 1:15 XL TD10 1:15

Drawing: XL TD 10
XLam Typical Details: B1 date: 09/03/2021
XLam Floor to Floor Lap Joint
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
19
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD11 1:15 XL TD11 nts

MAX CENTERS
BETWEEN FIXINGS MIN EDGE DISTANCE
100mm MIN

PARTIALLY THREADED
CONTINUOUS TIMBER EQ EQ MASS TIMBER SCREWS
SPLINE PLATE / PLY / LVL
D E
SD
FT
L

EQ

EQ
XLAM FLOOR PANEL Ø

SPLINE DEPTH

MIN FIXING LENGTH Ø = SCREW DIAMETER

L > (T/2) + (4 x Ø)

E Front view S Right view

XL TD11 1:15 XL TD11 1:15

Drawing: XL TD 11
XLam Typical Details: B2 date: 09/03/2021
XLam Floor to Floor Spline Joint
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
20
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD12 1:15 XL TD12 nts

MAX CENTERS
BETWEEN FIXINGS MIN EDGE DISTANCE WT

XLAM WALL PANEL

FULLY THREADED
MASS TIMBER SCREW
D E @ 45° ANGLE

FT

PARTIALLY THREADED
MASS TIMBER SCREW
L

XLAM FLOOR PANEL

XLAM WALL PANEL

MIN FIXING LENGTH

E Front view S Right view

XL TD12 1:15 XL TD12 1:15

Drawing: XL TD 12
XLam Typical Details: C1 date: 09/03/2021
XLam Wall to Floor Connection (Platform Construction)
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
21
 Technical Note 2.1 Standard Details V1

Bracket Dimensions are illustrative only and

110
specific bracket selection and dimensions are
brand and project design and specification
specific.

0
95 11

P Top view I Axo

XL TD13 1:15 XL TD13 nts

MIN DISTANCE
BETWEEN BRACKETS MIN EDGE DISTANCE
WT

XLAM WALL PANEL

NAIL/SCREW FIXINGS
TO SUIT BRACKET
D BE

MASS TIMBER BRACKET

FT

PARTIALLY THREADED
MASS TIMBER SCREW
L

XLAM FLOOR PANEL

CRS FE

XLAM WALL PANEL

MAX CENTERS
MIN FIXING LENGTH BETWEEN FIXINGS MAX EDGE DISTANCE

E Front view S Right view

XL TD13 1:15 XL TD13 1:15

Drawing: XL TD 13
XLam Typical Details: C2 date: 09/03/2021
XLam Wall to Floor Connection (Edge)
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
22
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD14 1:15 XL TD14 nts

MAX CENTERS
BETWEEN FIXINGS MIN EDGE DISTANCE

D E

FT
PARTIALLY THREADED
MASS TIMBER SCREW
L

XLAM FLOOR PANEL

XLAM WALL PANEL

MIN FIXING LENGTH

WT

E Front view S Right view

XL TD14 1:15 XL TD14 1:15

Drawing: XL TD 14
XLam Typical Details: C3 date: 09/03/2021
XLam Wall to Floor Connection (Edge)
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
23
 Technical Note 2.1 Standard Details V1

MIN FIXING LENGTH

P Top view I Axo

XL TD15 1:15 XL TD15 1:~

WT
MAX CENTERS
BETWEEN FIXINGS MIN EDGE DISTANCE

PARTIALLY THREADED
XLAM WALL PANEL
D E MASS TIMBER SCREW
@ 45° ANGLE
FT

XLAM FLOOR PANEL

FULLY THREADED
MASS TIMBER SCREW

TIMBER CORBEL

E Front view S Right view

XL TD15 1:15 XL TD15 1:15

Drawing: XL TD 15
XLam Typical Details: C4 date: 09/03/2021
XLam Wall to Floor Connection (Balloon Construction)
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
24
 Technical Note 2.1 Standard Details V1

20
A.L

90

Bracket Dimensions are illustrative only and

MIN EMBEDMENT specific bracket selection and dimensions are
90 brand and project design and specification
specific.
it
t o su
gth
Len

P Top view I Axo

XL TD16 1:15 XL TD16 nts

MAX CENTERS
BETWEEN FIXINGS MIN EDGE DISTANCE

CONCRETE WALL
TOLERANCE
TO CONCRETE WALL
D E
MASS TIMBER FIXING
FT
F.L

XLAM FLOOR PANEL

ANCHOR TO SUIT ANGLE

CONTINUOUS STEEL ANGLE

MIN FIXING LENGTH

E Front view S Right view

XL TD16 1:15 XL TD16 1:15

Drawing: XL TD 16
XLam Typical Details: C5 date: 09/03/2021
XLam Floor to Concrete Wall Connection (Edge)
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
25
 Technical Note 2.1 Standard Details V1

440
Bracket Dimensions are illustrative only and
specific bracket selection and dimensions are
brand and project design and specification
specific.

60 63
P Top view I Axo
XL TD17 1:15 XL TD17 nts

MIN EDGE DISTANCE

WT

FIXINGS TO SUIT
BRACKET

WHT MASS TIMBER BRACKETS

XLAM WALLS
FT

XLAM FLOOR

BOLT TO SUIT BRACKETS

E Front view S Right view

XL TD17 1:15 XL TD17 1:15

Drawing: XL TD 17
XLam Typical Details: C6 date: 09/03/2021
XLam Wall to Floor Hold Down Connection (Edge)
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
26
 Technical Note 2.1 Standard Details V1

SLOT THROUGH XLAM FLOOR

FOR MASS TIMBER PLATE

20
80

75

594
Bracket Dimensions are illustrative only and
specific bracket selection and dimensions are
brand and project design and specification
specific.

P Top view I Axo

XL TD18 1:15 XL TD18 nts

WT
MIN EDGE DISTANCE

FIXINGS TO SUIT
BRACKET
E

MASS TIMBER PLATE

XLAM WALLS
FT

XLAM FLOOR

E Front view S Right view

XL TD18 1:15 XL TD18 1:15

Drawing: XL TD 18
XLam Typical Details: C7 date: 09/03/2021
XLam Wall to Wall Hold Down Connection (Edge)
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
27
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD19 1:15 XL TD19 nts

MAX CENTERS 50mm MIN

BETWEEN FIXINGS MIN EDGE DISTANCE

EQ PARTIALLY THREADED
MASS TIMBER SCREW
D E EQ
EQ

FT
EQ
L

XLAM FLOOR PANEL

XLAM WALL PANEL

MIN FIXING LENGTH

WT

E Front view S Right view

XL TD19 1:15 XL TD19 1:15

Drawing: XL TD 19
XLam Typical Details: D1 date: 09/03/2021
XLam Floor to Floor Half Lap Connection (Over Wall)
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
28
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD20 1:15 XL TD20 nts

MAX CENTERS
BETWEEN FIXINGS MIN EDGE DISTANCE

PARTIALLY THREADED
MASS TIMBER SCREW
D E

FT
L

XLAM FLOOR PANEL

XLAM WALL PANEL

MIN FIXING LENGTH

WT

E Front view S Right view

XL TD20 1:15 XL TD20 1:15

Drawing: XL TD 20
XLam Typical Details: D2 date: 09/03/2021
XLam Floor to Wall Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
29
 Technical Note 2.1 Standard Details V1

Bracket Dimensions are illustrative only and

specific bracket selection and dimensions are

170
brand and project design and specification
specific.

95 110
P Top view I Axo
XL TD21 1:15 XL TD21 nts

MIN DISTANCE
BETWEEN BRACKETS MIN EDGE DISTANCE WT

XLAM WALL PANEL

NAIL/SCREW FIXINGS
TO SUIT BRACKET

D E

MASS TIMBER BRACKET

FT

XLAM FLOOR PANEL

E Front view S Right view

XL TD21 1:15 XL TD21 1:15

Drawing: XL TD 21
XLam Typical Details: D3 date: 09/03/2021
XLam Wall to Floor Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
30
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD22 1:15 XL TD22 nts

MAX CENTERS WT
BETWEEN FIXINGS MIN EDGE DISTANCE

XLAM WALL PANEL

FULLY THREADED
MASS TIMBER SCREW
@ 45° ANGLE
D E
FT

XLAM FLOOR PANEL

E Front view S Right view

XL TD22 1:15 XL TD22 1:15

Drawing: XL TD 22
XLam Typical Details: D4 date: 09/03/2021
XLam Wall to Floor Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
31
 Technical Note 2.1 Standard Details V1

WT

PARTIALLY THREADED
MASS TIMBER SCREW
XLAM WALL PANEL

50mm MIN
EQ
EQ

XLAM WALL PANEL

P Top view I Axo

XL TD23 1:15 XL TD23 nts

MIN EDGE DISTANCE

E

MAX CENTERS
BETWEEM FIXINGS
D

MIN FIXING LENGTH

L

E Front view S Right view

XL TD23 1:15 XL TD23 1:15

Drawing: XL TD 23
XLam Typical Details: E1 date: 09/03/2021
XLam Wall to Wall Half Lap Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
32
 Technical Note 2.1 Standard Details V1

WT

MIN FIXING LENGTH

FULLY THREADED
L

MASS TIMBER SCREWS

XLAM WALL PANEL

XLAM WALL PANEL

P Top view I Axo

XL TD24 1:15 XL TD24 nts

MIN EDGE DISTANCE

E

MAX CENTERS
BETWEEM FIXINGS
D

E Front view S Right view

XL TD24 1:15 XL TD24 1:15

Drawing: XL TD 24
XLam Typical Details: E2 date: 09/03/2021
XLam Wall to Wall Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
33
 Technical Note 2.1 Standard Details V1

WT

PARTIALLY THREADED
MASS TIMBER SCREW

XLAM WALL PANEL

XLAM WALL PANEL

P Top view I Axo

XL TD25 1:15 XL TD25 nts

MIN EDGE DISTANCE

E

MAX CENTERS
BETWEEM FIXINGS
D

MIN FIXING LENGTH

L

E Front view S Right view

XL TD25 1:15 XL TD25 1:15

Drawing: XL TD 25
XLam Typical Details: E3 date: 09/03/2021
XLam Wall to Wall Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
34
 Technical Note 2.1 Standard Details V1

W
T
MIN FIXING LENGTH

XLAM WALL PANEL

L

XLAM WALL PANEL

P Top view I Axo

XL TD26 1:15 XL TD26 nts

MIN EDGE DISTANCE

E

MAX CENTERS
BETWEEM FIXINGS
D

E Front view S Right view

XL TD26 1:15 XL TD26 1:15

Drawing: XL TD 26
XLam Typical Details: E4 date: 09/03/2021
XLam Wall to Wall Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
35
 Technical Note 2.1 Standard Details V1

W
T
MIN FIXING LENGTH

XLAM WALL PANEL

L

XLAM WALL PANEL

P Top view I Axo

XL TD27 1:15 XL TD27 nts

MIN EDGE DISTANCE

E

MAX CENTERS
BETWEEM FIXINGS
D

E Front view S Right view

XL TD27 1:15 XL TD27 1:15

Drawing: XL TD 27
XLam Typical Details: E5 date: 09/03/2021
XLam Wall to Wall Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
36
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD28 1:15 XL TD28 nts

CENTERS
BETWEEN ANCHORS EDGE DISTANCE

XLAM AIRSTAIR
AT

E D E

CHEMSET ANCHOR
R
TH

10mm TOLERANCE
STRUCTURAL THROAT TO CONCRETE
10
L

MIN EMBEDMENT

Fixing of Balustrades to XLam Airstairs is common

E Front view S Right view practice. In general screw fixings should always be into
cross grain lamellas as opposed to end grain lamellas.
XL TD28 1:15 XL TD28 1:15 Specific advice should be sought from the balustrade
manufacturer.

Drawing: XL TD 28
XLam Typical Details: F1 date: 09/03/2021
XLam Airstair to Concrete Landing Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
37
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD29 1:15 XL TD29 nts

MAX CENTERS
BETWEEN FIXINGS MIN EDGE DISTANCE

XLAM AIRSTAIR

E
AT

D
PARTIALLY THREADED
MASS TIMBER SCREW
R
TH

STRUCTURAL THROAT
R.D
L

MIN FIXING LENGTH XLAM LANDING

Fixing of Balustrades to XLam Airstairs is common

E Front view S Right view practice. In general screw fixings should always be into
cross grain lamellas as opposed to end grain lamellas.
XL TD29 1:15 XL TD29 1:15 Specific advice should be sought from the balustrade
manufacturer.

Drawing: XL TD 29
XLam Typical Details: F2 date: 09/03/2021
XLam Airstair to XLam Landing Bottom Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
38
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD30 1:15 XL TD30 nts
AT

XLAM AIRSTAIR
R
TH

STRUCTURAL THROAT
D

L.T

E W E

XLAM LANDING

Fixing of Balustrades to XLam Airstairs is common

E Front view S Right view practice. In general screw fixings should always be into
cross grain lamellas as opposed to end grain lamellas.
XL TD30 1:15 XL TD30 1:15 Specific advice should be sought from the balustrade
manufacturer.

Drawing: XL TD 30
XLam Typical Details: F3 date: 09/03/2021
XLam Airstair to XLam Landing Sliding Bottom Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
39
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD31 1:15 XL TD31 nts

XLAM AIRSTAIR
AT

PLASTIC BETWEEN AIRSTAIR

R
TH

AND LANDING
L.T

STRUCTURAL THROAT

Fixing of Balustrades to XLam Airstairs is common

E Front view S Right view practice. In general screw fixings should always be into
cross grain lamellas as opposed to end grain lamellas.
XL TD31 1:15 XL TD31 1:15 Specific advice should be sought from the balustrade
manufacturer.

Drawing: XL TD 31
XLam Typical Details: F4 date: 09/03/2021
XLam Airstair to XLam Landing Plastic Sliding Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
40
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD32 1:15 XL TD32 nts

MAX CENTERS
BETWEEN FIXINGS MIN EDGE DISTANCE

MIN FIXING LENGTH

E XLAM LANDING
D
20
L.T

XLAM AIRSTAIR
L

R
TH

STRUCTURAL THROAT
AT

Fixing of Balustrades to XLam Airstairs is common

E Front view S Right view practice. In general screw fixings should always be into
cross grain lamellas as opposed to end grain lamellas.
XL TD32 1:15 XL TD32 1:15 Specific advice should be sought from the balustrade
manufacturer.

Drawing: XL TD 32
XLam Typical Details: F5 date: 09/03/2021
XLam Airstair to XLam Landing Sloped Seating Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
41
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD33 1:15 XL TD33 nts

MAX CENTERS
BETWEEN FIXINGS MIN EDGE DISTANCE

MIN FIXING LENGTH

E
D XLAM LANDING
XLAM AIRSTAIR
EQ
L.T

L
EQ

R
TH
/2
<1

R
TH

AT

STRUCTURAL THROAT

Fixing of Balustrades to XLam Airstairs is common

E Front view S Right view practice. In general screw fixings should always be into
cross grain lamellas as opposed to end grain lamellas.
XL TD33 1:15 XL TD33 1:15 Specific advice should be sought from the balustrade
manufacturer.

Drawing: XL TD 33
XLam Typical Details: F6 date: 09/03/2021
XLam Airstair to XLam Landing Lap Joint Seating Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
42
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD34 1:15 XL TD34 nts
AT

XLAM AIRSTAIR

MIN FIXING LENGTH

CORBEL
L

R
TH

D
MAX CENTERS
BETWEEN FIXINGS E

MIN EDGE DISTANCE

STRUCTURAL THROAT

Fixing of Balustrades to XLam Airstairs is common

E Front view S Right view practice. In general screw fixings should always be into
cross grain lamellas as opposed to end grain lamellas.
XL TD34 1:15 XL TD34 1:15 Specific advice should be sought from the balustrade
manufacturer.

Drawing: XL TD 34
XLam Typical Details: F7 date: 09/03/2021
XLam Airstair to Corbel Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
43
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD35 1:15 XL TD35 nts

MAX CENTERS
BETWEEN FIXINGS MIN EDGE DISTANCE

MIN FIXING LENGTH PARTIALLY THREADED

MASS TIMBER SCREWS

D E
XLAM ROOF
L

RT

ENGINEERED
TIMBER BEARER

E Front view S Right view

XL TD35 1:15 XL TD35 1:15

Drawing: XL TD 35
XLam Typical Details: G1 date: 09/03/2021
XLam Roof to Roof Connection (Ridge Beam)
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
44
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD36 1:15 XL TD36 nts

MAX CENTERS
BETWEEN FIXINGS MIN EDGE DISTANCE

MIN FIXING LENGTH

PARTIALLY THREADED
D E MASS TIMBER SCREWS

XLAM ROOF
RT

E Front view S Right view

XL TD36 1:15 XL TD36 1:15

Drawing: XL TD 36
XLam Typical Details: G2 date: 09/03/2021
XLam Roof to Roof Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
45
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD37 1:15 XL TD37 nts

MAX CENTERS
BETWEEN FIXINGS MIN EDGE DISTANCE

D E
XLAM ROOF

RT
L

PARTIALLY THREADED
MASS TIMBER SCREWS

XLAM WALL

MIN FIXING LENGTH

WT

E Front view S Right view

XL TD37 1:15 XL TD37 1:15

Drawing: XL TD 37
XLam Typical Details: G3 date: 09/03/2021
XLam Wall to Roof Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
46
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD38 1:15 XL TD38 nts

MAX CENTERS
BETWEEN FIXINGS MIN EDGE DISTANCE

D E
XLAM ROOF RT
L

PARTIALLY THREADED
MASS TIMBER SCREWS

XLAM WALL

MIN FIXING LENGTH

WT

E Front view S Right view

XL TD38 1:15 XL TD38 1:15

Drawing: XL TD 38
XLam Typical Details: G4 date: 09/03/2021
XLam Wall to Roof Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
47
 Technical Note 2.1 Standard Details V1

50mm MIN

EQ

EQ
EQ
EQ

P Top view I Axo

XL TD39 1:15 XL TD39 nts

XLAM WALL XLAM LINTEL WT PARTIALLY THREADED

MIN EDGE DISTANCE MASS TIMBER SCREWS
E
D

MAX CENTERS
BETWEEN FIXINGS
L

MIN FIXING LENGTH

MIN SEATING

E Front view S Right view

XL TD39 1:15 XL TD39 1:15

Drawing: XL TD 39
XLam Typical Details: H1 date: 09/03/2021
XLam Lintel to Wall Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
48
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD40 1:15 XL TD40 nts

MAX CENTERS
BETWEEN FIXINGS MIN EDGE DISTANCE

50mm MIN PARTIALLY THREADED

MASS TIMBER SCREWS
D E
XLAM FLOOR
SET-DOWN

EQ

FT
EQ
L

XLAM WALL

MIN FIXING LENGTH

WT

E Front view S Right view

XL TD40 1:15 XL TD40 1:15

Drawing: XL TD 40
XLam Typical Details: J1 date: 09/03/2021
XLam Floor to Floor Set-Down (Over Wall)
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
49
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD41 1:15 XL TD41 nts

MAX CENTERS
BETWEEN FIXINGS MIN EDGE DISTANCE

PARTIALLY THREADED
50mm MIN
MASS TIMBER SCREWS
D E

XLAM FLOOR
FT
EQ
L

EQ

MIN FIXING LENGTH

E Front view S Right view

XL TD41 1:15 XL TD41 1:15

Drawing: XL TD 41
XLam Typical Details: J2 date: 09/03/2021
XLam Floor to Floor Set-Down
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
50
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD42 1:15 XL TD42 nts

MAX CENTERS
BETWEEN FIXINGS MIN EDGE DISTANCE

50mm MIN PARTIALLY THREADED

MASS TIMBER SCREWS
D E
XLAM FLOOR
EQ

FT
L

EQ

MIN FIXING LENGTH

E Front view S Right view

XL TD42 1:15 XL TD42 1:15

Drawing: XL TD 42
XLam Typical Details: J3 date: 09/03/2021
XLam Floor to Floor Set-Down
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
51
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD43 1:15 XL TD43 nts

MAX CENTERS
BETWEEN FIXINGS MIN EDGE DISTANCE

D E XLAM FLOOR

MIN FIXING LENGTH

FT
L

XLAM FLOOR

CORBEL

XLAM WALL

WT

E Front view S Right view

XL TD43 1:15 XL TD43 1:15

Drawing: XL TD 43
XLam Typical Details: J4 date: 09/03/2021
XLam Floor to Floor Corbel Set-Down (Over Wall)
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
52
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD44 1:15 XL TD44 nts

MAX CENTERS
BETWEEN FIXINGS MIN EDGE DISTANCE

D E MASS TIMBER FIXING

XLAM FLOOR

FT
L

STEEL BEAM

MIN FIXING LENGTH

E Front view S Right view

XL TD44 1:15 XL TD44 1:15

Drawing: XL TD 44
XLam Typical Details: K1 date: 09/03/2021
XLam Floor to Steel Beam Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
53
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD45 1:15 XL TD45 nts

MAX CENTERS
BETWEEN FIXINGS MIN EDGE DISTANCE

PARTIALLY THREADED
MASS TIMBER SCREWS

D E
MASS TIMBER FIXING
XLAM FLOOR
PT.L

FT
WH.L

STEEL PLATE

STEEL BEAM

PT MIN FIXING LENGTH WH MIN FIXING LENGTH

E Front view S Right view

XL TD45 1:15 XL TD45 1:15

Drawing: XL TD 45
XLam Typical Details: K2 date: 09/03/2021
XLam Floor to Floor Connection (Lap Joint Over Steel Beam)
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
54
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD46 1:15 XL TD46 nts

MAX CENTERS
BETWEEN FIXINGS MIN EDGE DISTANCE

STEEL RHS MASS TIMBER FIXING

D E
XLAM FLOOR
FT
L

STEEL PLATE

MIN FIXING LENGTH

E Front view S Right view

XL TD46 1:15 XL TD46 1:15

Drawing: XL TD 46
XLam Typical Details: K3 date: 09/03/2021
XLam Floor to RHS Beam Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
55
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD47 1:15 XL TD47 nts

MAX CENTERS
BETWEEN FIXINGS MIN EDGE DISTANCE

MIN FIXING LENGTH PARTIALLY THREADED

CONTINUOUS TIMBER
MASS TIMBER SCREWS
SPLINE PLATE
PT.E
MIN FIXING LENGTH PT.D
PT.L

FT
WH.L

WH.D WH.E XLAM FLOOR

MASS TIMBER FIXING

MAX CENTERS STEEL BEAM

BETWEEN FIXINGS MIN EDGE DISTANCE

E Front view S Right view

XL TD47 1:15 XL TD47 1:15

Drawing: XL TD 47
XLam Typical Details: K4 date: 09/03/2021
XLam Floor to Floor Connection (Spline Joint Over Steel Beam)
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
56
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD48 1:15 XL TD48 nts

MAX CENTERS
BETWEEN FIXINGS MIN EDGE DISTANCE

D E STEEL BEAM

XLAM FLOOR
FT
L

MASS TIMBER FIXING

5mm CHAMFER
MIN FIXING LENGTH

E Front view S Right view

XL TD48 1:15 XL TD48 1:15

Drawing: XL TD 48
XLam Typical Details: K5 date: 09/03/2021
XLam Floor to Steel Beam Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
57
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD49 1:15 XL TD49 nts

WT

XLAM WALL

E D D E
SLOT IN CLT WITH
SELF-PERFORATING DOWELS
TOLERANCE FOR
FINPLATE
SLOT DEPTH
350mm MAX

20mm TOLERANCE
TO CONCRETE
TO BE DRY PACKED

STEEL FINPLATE
20

CONCRETE SLAB

DPC BETWEEN CLT STEEL PLATE

AND CONCRETE
REBAR CAST IN CONCRETE

E Front view S Right view

XL TD49 1:15 XL TD49 1:15

Drawing: XL TD 49
XLam Typical Details: L1 date: 09/03/2021
XLam Wall to Concrete Fin plate Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
58
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD50 1:15 XL TD50 nts

WT

XLAM WALL

E E
D D SLOT IN CLT WITH SELF-PERFORATING DOWELS
TOLERANCE FOR
T-PLATE
T-PLATE WITH COUPLER NUTS
SLOT DEPTH
350mm MAX

20mm TOLERANCE
TO CONCRETE
TO BE DRY PACKED
20

CONCRETE SLAB

DPC BETWEEN CLT

AND CONCRETE
REBAR

DROSSBACH TUBING

E Front view S Right view

XL TD50 1:15 XL TD50 1:15

Drawing: XL TD 50
XLam Typical Details: L2 date: 09/03/2021
XLam Wall to Concrete Fin plate Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
59
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD51 1:15 XL TD51 nts

WT

XLAM WALL

E E
D D SLOT IN CLT WITH SELF-PERFORATING DOWELS
TOLERANCE FOR
T-PLATE
SLOT DEPTH
350mm MAX

T-PLATE

20mm TOLERANCE
TO CONCRETE
TO BE DRY PACKED
20

CONCRETE SLAB
L

CHEMSET ANCHOR

DPC BETWEEN CLT

MIN EMBEDMENT AND CONCRETE

E Front view S Right view

XL TD51 1:15 XL TD51 1:15

Drawing: XL TD 51
XLam Typical Details: L3 date: 09/03/2021
XLam Wall to Concrete Fin plate Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
60
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD52 1:15 XL TD52 nts

WT

XLAM WALL

E E
D D SLOT IN CLT WITH SELF-PERFORATING DOWELS
TOLERANCE FOR
FINPLATE STEEL FINPLATE
SLOT DEPTH
350mm MAX
L
L

E Front view S Right view

XL TD52 1:15 XL TD52 1:10

Drawing: XL TD 52
XLam Typical Details: L4 date: 09/03/2021
XLam Wall to Wall Fin plate Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
61
 Technical Note 2.1 Standard Details V1

WT

P Top view I Axo

XL TD53 1:15 XL TD53 nts

XLAM WALL

XLAM WALL

41
20
SHERPA CLT CONNECTOR
110

MASS TIMBER FIXINGS

TO SUIT SHERPA
CONNECTOR

E Front view S Right view

XL TD53 1:15 XL TD53 1:15

Drawing: XL TD 53
XLam Typical Details: M1 date: 09/03/2021
XLam Wall to Wall Sherpa Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
62
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD54 1:15 XL TD54 nts

WT

XLAM WALL

110 20
SHERPA CLT CONNECTOR
XLAM FLOOR
41

FT

MASS TIMBER FIXINGS

TO SUIT SHERPA
CONNECTOR

E Front view S Right view

XL TD54 1:15 XL TD54 1:15

Drawing: XL TD 54
XLam Typical Details: M2 date: 09/03/2021
XLam Floor to Wall Sherpa Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
63
 Technical Note 2.1 Standard Details V1

41

110

P Top view I Axo

XL TD55 1:15 XL TD55 nts

SHERPA CLT CONNECTOR

XLAM FLOOR
20
FT

MASS TIMBER FIXINGS

TO SUIT SHERPA
CONNECTOR

E Front view S Right view

XL TD55 1:15 XL TD55 1:15

Drawing: XL TD 55
XLam Typical Details: M3 date: 09/03/2021
XLam Floor to Floor Sherpa Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Cross Laminated Timber (CLT) only. The drawing is not intended as general information and
guidance for all manufactured Cross Laminated Timber (CLT). The information is specific to XLam CLT and no warranty is given to the suitability and application of the information to other manufacturers CLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
64
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD56 1:15 XL TD56 nts

BW

P.W GLULAM BEAM

SLOT FOR STEEL PLATE
BH
P.H

STEEL T-PLATE
DOWELS
L

PARTIALLY THREADED
MIN FIXING LENGTH MASS TIMBER SCREWS
GLULAM COLUMN

D D D
E E

CH
CW

E Front view S Right view

XL TD56 1:15 XL TD56 1:15

Drawing: XL TD 56
XLam Typical Details: N1 date: 09/03/2021
Glulam Beam to Column Connection (Screws)
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Glue Laminated Timber (GLT) only. The drawing is not intended as general information and
guidance for all manufactured Glue Laminated Timber (GLT). The information is specific to XLam GLT and no warranty is given to the suitability and application of the information to other manufacturers GLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
65
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD57 1:15 XL TD57 nts

BW

P.W GLULAM BEAM

SLOT FOR STEEL PLATE
BH
P.H

STEEL PLATE
DOWELS
L

MIN EMBEDMENT EPOXIED RODS

GLULAM COLUMN

E D E

CH
CW

E Front view S Right view

XL TD57 1:15 XL TD57 1:15

Drawing: XL TD 57
XLam Typical Details: N2 date: 09/03/2021
Glulam Beam to Column Connection (Epoxied Rods)
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Glue Laminated Timber (GLT) only. The drawing is not intended as general information and
guidance for all manufactured Glue Laminated Timber (GLT). The information is specific to XLam GLT and no warranty is given to the suitability and application of the information to other manufacturers GLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
66
 Technical Note 2.1 Standard Details V1

GLULAM BEAM

ALUMIDI CONNECTOR
GLULAM BEAM

FIXINGS TO SUIT
ALUMIDI CONNECTOR
DOWELS
SLOT TO SUIT
ALUMIDI CONNECTOR
GLULAM BEAM

BW

P Top view I Axo

XL TD58 1:15 XL TD58 nts

ALUMIDI CONNECTOR
E
D
D

BH
D
D
D
E

E Front view S Right view

XL TD58 1:15 XL TD58 1:15

Drawing: XL TD 58
XLam Typical Details: N3 date: 09/03/2021
Glulam Beam to Beam Alumidi Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Glue Laminated Timber (GLT) only. The drawing is not intended as general information and
guidance for all manufactured Glue Laminated Timber (GLT). The information is specific to XLam GLT and no warranty is given to the suitability and application of the information to other manufacturers GLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
67
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD59 1:15 XL TD59 nts

CW
CH

GLULAM COLUMN

ENGINEERED BOLTS
STEEL FINPLATE P.W

PARTIALLY THREADED STEEL BASEPLATE

MASS TIMBER SCREWS REBATED INTO FLOOR
P.H

XLAM FLOOR
FT

E Front view S Right view

XL TD59 1:15 XL TD59 1:15

Drawing: XL TD 59
XLam Typical Details: N4 date: 09/03/2021
Glulam Beam to Xlam Floor Steel Plate Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Glue/Cross Laminated Timber (GLT/CLT) only. The drawing is not intended as general
information and guidance for all manufactured Glue/Cross Laminated Timber (GLT/CLT). The information is specific to XLam GLT/CLT and no warranty is given to the suitability and application of the information to other
manufacturers GLT/CLT
REV: A

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
68
 Technical Note 2.1 Standard Details V1

P Top view I Axo

XL TD60 1:15 XL TD60 nts

CH
CW

GLULAM COLUMN
BREATHER HOLES

RODS EPOXIED IN COLUMN STEEL BASE CONNECTION

ANCHORS TO SUIT
BASE CONNECTION TOLERANCE TO SLAB
CONCRETE SLAB

E Front view S Right view

XL TD60 1:15 XL TD60 1:15

Drawing: XL TD 60
XLam Typical Details: N5 date: 09/03/2021
Glulam Beam to Concrete Slab Steel Base Connection
TM
DRW: TS - PR: JL
The information in the drawing is owned by XLam. The information is provided for use in the design and specification of XLam manufactured Glue Laminated Timber (GLT) only. The drawing is not intended as general information and
guidance for all manufactured Glue Laminated Timber (GLT). The information is specific to XLam GLT and no warranty is given to the suitability and application of the information to other manufacturers GLT
REV: A
.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
69
 Technical Note 2.1 Standard Details V1

Further Information
If you need any further information on the use of XLam panels, please contact [email protected] or
[email protected] and we will be happy to assist. We can provide information and introductions to
external consultants who can assist in your project.

Disclaimer
This Technical Note provides details and options of how XLam’s CLT panel may be installed and is not intended
to be used for certification purposes. The information provided in this document is supplied in good faith and
to the best of our knowledge was correct at the time of preparation. No responsibility can be accepted by
XLam, its staff or its agents for any errors or omissions. Users are advised to make their own determination
as to the suitability of this information in relation to their particular purposes and specific circumstances.
No warranty or assurance can be given that XLam CLT panels and the installation details provided will suit
individual projects. XLam disclaims all liability and responsibility for any loss or damage, direct or indirect,
which may be suffered by any person acting in reliance on anything contained in or omitted from this
Technical Note.

XLam Technical Note 2.1 Standard Details V1 Australian & New Zealand Edition | Jan 2022
70
XLam Australia XLam New Zealand
Suite 8, 4-10 Bank Place 60M Surrey Crescent
Melbourne Grey Lynn
Victoria 3000 Auckland 1021
AUSTRALIA NEW ZEALAND

[email protected] [email protected]

xlam.com.au I xlam.co.nz