Product information

Klüberoil GEM 1 N
High-performance gear and multipurpose oil based on mineral oil

Your benefits at a glance

High scuffing protection
Excellent wear protection for gears and rolling bearings
Good shear stability for reliable lubricant film formation
Excellent ageing and oxidation resistance
Low foaming tendency

Your requirements - our solution Klüberoil GEM 1 N can also be used for the lubrication of plain and
Klüberoil GEM 1 N is a high-performance gear and multipurpose oil rolling bearings, all kinds of toothed couplings, chains, guideways,
based on selected mineral oils satisfying the growing requirements joints, spindles and pumps.
and increasing power density of modern gears. Application notes
Klüberoil GEM 1 N clearly exceeds CLP requirements according to Klüberoil GEM 1 N can be applied by means of immersion,
DIN 51517-3. Corresponding gears can be switched to Klüberoil immersion circulation or injection.
GEM 1 N without prior consultation with the gear manufacturer
The use of drip-feed oilers, brushes, oil cans or suitable automatic
provided the general application notes are observed.
lubricating systems is also possible. When using automatic
Klüberoil GEM 1 N offers high scuffing load capacity. Gears are lubricating systems, please note the manufacturer's instructions
sufficiently protected against scuffing even at extremely high peak regarding the maximum permissible viscosity. The low-viscosity
loads, vibrations or oscillations. The excellent wear protection of varieties are also used for oil mist lubrication.
both gears and rolling bearings ensures that the service life
It should be noted that elastomers from one or several
calculated for the lubricated components is achieved, leading to
manufacturers can behave differently; therefore tests should be
lower maintenance and repair costs.
performed.
Klüberoil GEM 1 N offers a much longer service life than mineral oil-
For checking the contact pattern during running-in, the inspection
based standard gear oils due to the excellent ageing and oxidation
paint Klübertop P 39-462 Spray (Art. No. 081295) can be used.
resistance of the selected raw materials; thus service intervals can
be extended and maintenance costs reduced. The product's low When changing over to Klüberoil GEM 1 N, residues of a previously
foaming tendency and anti-corrosive properties enable problem-free used gear oil can be more easily removed if Klüber Summit
gear operation. Varnasolv HV (Article No. 050135) is added.
By using Klüberoil GEM 1 N you can benefit from a number of When determining the oil viscosity for gear lubrication, the gear
advantages that will help you save costs easily and efficiently. We manufacturer's instructions take priority. Only for applications where
look forward to hearing from you. manufacturer's instructions are not available, the suitable viscosity
can be determined as laid down in DIN 51509. To determine the
Application correct oil viscosity for bearings, please observe the bearing
Klüberoil GEM 1 N was specially developed for the lubrication of manufacturer's instructions.
spur, bevel and planetary gears that are subject to high loads. Such
gears are frequently used in the steel, mining and sugar industries. It
is also used for the lubrication of standard worm gears as defined in
DIN 3996.

Klüberoil GEM 1 N , 030062, 030049, 030058, 030064, 030057, 030054, 030051, 030050, 030063,
en-GB
Edition 22.09.2023 - replaces edition 03.03.2023
Product information

Klüberoil GEM 1 N
High-performance gear and multipurpose oil based on mineral oil

Material safety data sheets

Material safety data sheets can be requested via our website
www.klueber.com. You may also obtain them through your contact
person at Klüber Lubrication.

Pack sizes Klüberoil GEM Klüberoil GEM Klüberoil GEM Klüberoil GEM
1-46 N 1-68 N 1-100 N 1-150 N

Canister 500 ml +
Canister 1 l + + + +
Canister 5 l + + + +
Canister 20 l + + + +
Canister 30 l +
Drum 200 l + + + +

Pack sizes Klüberoil GEM Klüberoil GEM Klüberoil GEM Klüberoil GEM
1-220 N 1-320 N 1-460 N 1-680 N

Canister 500 ml
Canister 1 l + + + +
Canister 5 l + +
Canister 20 l + + + +
Canister 30 l
Drum 200 l + + + +

Pack sizes Klüberoil GEM 1-1000 N

Canister 500 ml
Canister 1 l
Canister 5 l
Canister 20 l +
Canister 30 l
Drum 200 l +

Characteristics Klüberoil GEM Klüberoil GEM Klüberoil GEM Klüberoil GEM

1-46 N 1-68 N 1-100 N 1-150 N

Article number 030050 030051 030054 030057

Service temperature, lower limit -15 °C -15 °C -5 °C -5 °C
Service temperature, upper limit 100 °C 100 °C 100 °C 100 °C

Klüberoil GEM 1 N , 030062, 030049, 030058, 030064, 030057, 030054, 030051, 030050, 030063,
en-GB
Edition 22.09.2023 - replaces edition 03.03.2023
Product information

Klüberoil GEM 1 N
High-performance gear and multipurpose oil based on mineral oil

Characteristics Klüberoil GEM Klüberoil GEM Klüberoil GEM Klüberoil GEM

1-46 N 1-68 N 1-100 N 1-150 N

Designation, DIN 51502 CLP 46 CLP 68 CLP 100 CLP 150

Designation, ISO 12925-1 CKC 46 CKC 68 CKC 100 CKC 150
Density, DIN 51757, 15°C approx. 870 kg/m³ approx. 880 kg/m³ approx. 880 kg/m³ approx. 880 kg/m³
Flash point, DIN EN ISO 2592, Cleveland open cup ≥ 200 °C ≥ 200 °C ≥ 200 °C ≥ 200 °C
Foam test, ISO 6247 / ASTM D892, 24°C, sequence I ≤ 100/10 ml ≤ 100/10 ml ≤ 100/10 ml ≤ 100/10 ml
Foam test, ISO 6247 / ASTM D892, 24°C, sequence ≤ 100/10 ml ≤ 100/10 ml ≤ 100/10 ml ≤ 100/10 ml
III
Foam test, ISO 6247 / ASTM D892, 93.5°C, ≤ 100/10 ml ≤ 100/10 ml ≤ 100/10 ml ≤ 100/10 ml
sequence II
ISO viscosity grade, DIN ISO 3448, ISO VG 46 68 100 150
Kinematic viscosity, DIN EN ISO 3104 / DIN 51562-1 approx. 7 mm²/s approx. 9 mm²/s approx. 11 mm²/s approx. 15 mm²/s
/ ASTM D445 / ASTM D7042, 100°C
Kinematic viscosity, DIN EN ISO 3104 / DIN 51562-1 approx. 46 mm²/s approx. 68 mm²/s approx. 100 mm²/s approx. 150 mm²/s
/ ASTM D445 / ASTM D7042, 40°C
Viscosity index, DIN ISO 2909 ≥ 90 ≥ 90 ≥ 90 ≥ 90
Copper corrosion, DIN EN ISO 2160, 3 h, 100°C 1 - 100 - 3 1 - 100 - 3 1 - 100 - 3 1 - 100 - 3
corrosion degree corrosion degree corrosion degree corrosion degree
Steel corrosion, DIN ISO 7120 / ASTM D665, method rust-free rust-free rust-free rust-free
A, 24 h, 60°C
Pour point, DIN ISO 3016 ≤ -20 °C ≤ -15 °C ≤ -15 °C ≤ -10 °C
Ageing behaviour, DIN EN ISO 4263-4 / ASTM ≤6% ≤6% ≤6% ≤6%
D2893, 312 h, 95°C, increase in viscosity at 100°C
FAG FE8 rolling bearing test, DIN 51819-3, D-7.5 / ≤ 200 mg ≤ 200 mg ≤ 200 mg ≤ 200 mg
80-80, wear of cage
FAG FE8 rolling bearing test, DIN 51819-3, D-7.5 / ≤ 30 mg ≤ 30 mg ≤ 30 mg ≤ 30 mg
80-80, wear of rolling elements
FZG scuffing test, DIN ISO 14635-1, A / 8.3 / 90, ≥ 12 ≥ 12 ≥ 12 ≥ 12
failure load stage
Minimum shelf life from the date of manufacture - in a 60 months 60 months 60 months 60 months
dry, frost-free place and in the unopened original
container, approx.

Characteristics Klüberoil GEM Klüberoil GEM Klüberoil GEM Klüberoil GEM

1-220 N 1-320 N 1-460 N 1-680 N

Article number 030058 030062 030063 030064

Service temperature, lower limit -5 °C -5 °C -5 °C 0 °C
Service temperature, upper limit 100 °C 100 °C 100 °C 100 °C
Designation, DIN 51502 CLP 220 CLP 320 CLP 460 CLP 680

Klüberoil GEM 1 N , 030062, 030049, 030058, 030064, 030057, 030054, 030051, 030050, 030063,
en-GB
Edition 22.09.2023 - replaces edition 03.03.2023
Product information

Klüberoil GEM 1 N
High-performance gear and multipurpose oil based on mineral oil

Characteristics Klüberoil GEM Klüberoil GEM Klüberoil GEM Klüberoil GEM

1-220 N 1-320 N 1-460 N 1-680 N

Designation, ISO 12925-1 CKC 220 CKC 320 CKC 460 CKC 680
Density, DIN 51757, 15°C approx. 890 kg/m³ approx. 900 kg/m³ approx. 910 kg/m³ approx. 930 kg/m³
Flash point, DIN EN ISO 2592, Cleveland open cup ≥ 200 °C ≥ 200 °C ≥ 200 °C ≥ 200 °C
Foam test, ISO 6247 / ASTM D892, 24°C, sequence I ≤ 100/10 ml ≤ 100/10 ml ≤ 100/10 ml ≤ 100/10 ml
Foam test, ISO 6247 / ASTM D892, 24°C, sequence ≤ 100/10 ml ≤ 100/10 ml ≤ 100/10 ml ≤ 100/10 ml
III
Foam test, ISO 6247 / ASTM D892, 93.5°C, ≤ 100/10 ml ≤ 100/10 ml ≤ 100/10 ml ≤ 100/10 ml
sequence II
ISO viscosity grade, DIN ISO 3448, ISO VG 220 320 460 680
Kinematic viscosity, DIN EN ISO 3104 / DIN 51562-1 approx. 19 mm²/s approx. 25 mm²/s approx. 30 mm²/s approx. 37 mm²/s
/ ASTM D445 / ASTM D7042, 100°C
Kinematic viscosity, DIN EN ISO 3104 / DIN 51562-1 approx. 220 mm²/s approx. 320 mm²/s approx. 460 mm²/s approx. 680 mm²/s
/ ASTM D445 / ASTM D7042, 40°C
Viscosity index, DIN ISO 2909 ≥ 90 ≥ 90 ≥ 90 ≥ 85
Copper corrosion, DIN EN ISO 2160, 3 h, 100°C 1 - 100 - 3 1 - 100 - 3 1 - 100 - 3 1 - 100 - 3
corrosion degree corrosion degree corrosion degree corrosion degree
Steel corrosion, DIN ISO 7120 / ASTM D665, method rust-free rust-free rust-free rust-free
A, 24 h, 60°C
Pour point, DIN ISO 3016 ≤ -10 °C ≤ -10 °C ≤ -10 °C ≤ -5 °C
Ageing behaviour, DIN EN ISO 4263-4 / ASTM ≤6% ≤6% ≤6% ≤6%
D2893, 312 h, 95°C, increase in viscosity at 100°C
FAG FE8 rolling bearing test, DIN 51819-3, D-7.5 / ≤ 200 mg ≤ 200 mg ≤ 200 mg ≤ 200 mg
80-80, wear of cage
FAG FE8 rolling bearing test, DIN 51819-3, D-7.5 / ≤ 30 mg ≤ 30 mg ≤ 30 mg ≤ 30 mg
80-80, wear of rolling elements
FZG scuffing test, DIN ISO 14635-1, A / 8.3 / 90, ≥ 12 ≥ 12 ≥ 12 ≥ 12
failure load stage
Minimum shelf life from the date of manufacture - in a 60 months 60 months 60 months 60 months
dry, frost-free place and in the unopened original
container, approx.

Characteristics Klüberoil GEM 1-1000 N

Article number 030049

Service temperature, lower limit 0 °C
Service temperature, upper limit 100 °C
Designation, DIN 51502 CLP 1000
Designation, ISO 12925-1 CKC 1000

Klüberoil GEM 1 N , 030062, 030049, 030058, 030064, 030057, 030054, 030051, 030050, 030063,
en-GB
Edition 22.09.2023 - replaces edition 03.03.2023
Product information

Klüberoil GEM 1 N
High-performance gear and multipurpose oil based on mineral oil

Characteristics Klüberoil GEM 1-1000 N

Density, DIN 51757, 15°C approx. 920 kg/m³

Flash point, DIN EN ISO 2592, Cleveland open cup ≥ 200 °C
Foam test, ISO 6247 / ASTM D892, 24°C, sequence I ≤ 100/10 ml
Foam test, ISO 6247 / ASTM D892, 24°C, sequence ≤ 100/10 ml
III
Foam test, ISO 6247 / ASTM D892, 93.5°C, sequence ≤ 100/10 ml
II
ISO viscosity grade, DIN ISO 3448, ISO VG 1000
Kinematic viscosity, DIN EN ISO 3104 / DIN 51562-1 / approx. 48 mm²/s
ASTM D445 / ASTM D7042, 100°C
Kinematic viscosity, DIN EN ISO 3104 / DIN 51562-1 / approx. 1000 mm²/s
ASTM D445 / ASTM D7042, 40°C
Viscosity index, DIN ISO 2909 ≥ 85
Copper corrosion, DIN EN ISO 2160, 3 h, 100°C 1 - 100 - 3 corrosion degree
Steel corrosion, DIN ISO 7120 / ASTM D665, method rust-free
A, 24 h, 60°C
Pour point, DIN ISO 3016 ≤ -3 °C
Ageing behaviour, DIN EN ISO 4263-4 / ASTM ≤6%
D2893, 312 h, 95°C, increase in viscosity at 100°C
FAG FE8 rolling bearing test, DIN 51819-3, D-7.5 / ≤ 200 mg
80-80, wear of cage
FAG FE8 rolling bearing test, DIN 51819-3, D-7.5 / ≤ 30 mg
80-80, wear of rolling elements
FZG scuffing test, DIN ISO 14635-1, A / 8.3 / 90, ≥ 12
failure load stage
Minimum shelf life from the date of manufacture - in a 60 months
dry, frost-free place and in the unopened original
container, approx.

Klüberoil GEM 1 N , 030062, 030049, 030058, 030064, 030057, 030054, 030051, 030050, 030063,
en-GB
Edition 22.09.2023 - replaces edition 03.03.2023
Product information

Klüberoil GEM 1 N
High-performance gear and multipurpose oil based on mineral oil

Klüber Lubrication München GmbH & Co. KG /

Geisenhausenerstraße 7 / 81379 München / Germany /
Klüber Lubrication – your global specialist phone +49 89 7876-0 / fax +49 89 7876-333.
Innovative tribological solutions are our passion. Through personal The data in this document is based on our general experience and knowledge at the time of
contact and consultation, we help our customers to be successful publication and is intended to give information of possible applications to a reader with technical
experience. It constitutes neither an assurance of product properties nor does it release the user
worldwide, in all industries and markets. With our ambitious technical
from the obligation of performing preliminary field tests with the product selected for a specific
concepts and experienced, competent staff we have been fulfilling application. All data are guide values which depend on the lubricant's composition, the intended
increasingly demanding requirements by manufacturing efficient high- use and the application method. The technical values of lubricants change depending on the
performance lubricants for more than 90 years. mechanical, dynamical, chemical and thermal loads, time and pressure. These changes may
affect the function of a component. We recommend contacting us to discuss your specific
application. If possible we will be pleased to provide a sample for testing on request. Klüber
products are continually improved. Therefore, Klüber Lubrication reserves the right to change all
the technical data in this document at any time without notice.

Publisher and Copyright: Klüber Lubrication München GmbH & Co. KG. Reprints, total or in
part, are permitted only prior consultation with Klüber Lubrication München GmbH & Co. KG
and if source is indicated and voucher copy is forwarded.

Klüberoil GEM 1 N , 030062, 030049, 030058, 030064, 030057, 030054, 030051, 030050, 030063,
en-GB
Edition 22.09.2023 - replaces edition 03.03.2023