290/350 SERIES

ACTORY CA
Operator and Parts Manual
29O Rider Scrubber
350 Rider Scrubber

R.P.S. Corporation Phone: 1-800-634-4060

P.O. Box 368 Fax: 1-866-901-3335
Racine, Wisconsin 53401

www.factorycat.com
chadv 11/23/2005 9:54:13 AM
 ACTORY CA
290/350 RIDER SCRUBBERS

THESE TOUGH, COMPACT SCRUBBERS COMBINED THE PRODUCTIVITY OF RIDERS WITH THE
MANEUVERABILITY OF WALK-BEHINDS. FACTORY CATS ARE DESIGNED TO CLEAN SCHOOLS, MALLS,
WAREHOUSES, RETAIL OUTLETS, WHILE STANDING UP TO THE RIGORS OF CONTRACT CLEANING.

WITH TWO SPECIALIZED CLEANING SYSTEMS TO CHOOSE FROM, FACTORY CATS OFFER THE
PERFORMANCE AND CAPACITY REQUIRED TO CLEAN YOUR UNIQUE APPLICATION.

THE TWO "DISK" MACHINES, WITH 29", AND 35" SCRUB PATHS, OFFER GIMBALED BRUSH DRIVE AND 35%
MORE SCRUBBING POWER THAN COMPETITIVE BRANDS.

THE "CYLINDRICAL" MACHINES, OFFER ALL THE PERFORMANCE OF DISK SCRUBBERS PLUS THE ABILITY TO
SWEEP. THE CYLINDRICAL PICKS UP WOODCHIPS, NAILS, BROKEN GLASS, GRAVEL, AND METAL CHIPS.
THE DEBRIS IS HELD IN THE SLIDE-OUT HOPPER WHICH PERMITS EASY DISPOSAL.

PRODUCTIVITY IS A FUNCTION OF SCRUB WIDTH, RUN TIME AND TANK CAPACITY. THESE FACTORY CATS
TOP THE CHART, WHILE MAINTAINING UNSURPASSED MANUVERABILITY. WITH 40% LARGER TANKS,
WIDER SCRUB PATHS, HIGHER SCRUBING PRESSURES, MORE VACUUM, AND BIGGER BATTERY PACKS
YOU WILL HAVE LESS STOPPING TO REFILL, FEWER TRIPS DOWN THE AISLE, LESS DOUBLE SCRUBBING,
DRY SAFE CLEAN FLOORS, AND EXTRA RUN TIME.

THE OPERATOR SITS IN A SPRING- SUSPENSIONED, FULLY ADJUSTABLE, MID-BACK CHAIR. THE STEERING
COLUMN HAS FOUR SETTINGS, FURTHER ENHANCING OPERATOR COMFORT. HEADLIGHT, HORN
BACKUP ALARM, NON-MARKING TIRES, AND ARMRESTS ARE STANDARD. OPERATORS ARE ABLE TO
TURN WITHIN A 64" AISLE, WHILE MAINTAINING EXCELLENT WATER CONTROL. WE ALSO OFFER, FOR
CLEANING IN REMOTE AREAS, A COMPLETE LINE OF HAND TOOLS, INCLUDING VAC WANDS, SPRAY
HOSES, AND POWERED SCRUB WANDS.

FACTORY CATS EXCLUSIVE "CENTRAL COMMAND II" ENERGY MANAGEMENT SYSTEM OFFERS
AUTOMATIC CONTROLS. WHEN THE OPERATOR STOPS THE MACHINE, BRUSHES, AND SOLUTION FLOW
STOPS, THE SAFETY-SET PARKING BRAKE IS APPLIED, AND VACUUM STOPS AFTER A 22 SECOND DELAY.
ALL "CENTRAL COMMAND" COMPONENTS, INCLUDING THE CURTIS CONTROLLER, AUTO REST CIRCUIT
BREAKERS, AND MARINE DUTY SWITCHES, ARE IN A SEALED MODULE.

FACTORY CATS USE THE MOST POWERFUL MOTORS AVALIABLE, SO THEY ARE TYPICALLY RUN AT ONLY
75% OF THEIR CAPACITY. THIS LEAVES POWER IN RESERVE FOR TIMES WHERE HEAVY STRIPPING IS
REQUIRED, AND GREATLY PROLONGS MOTOR LIFE. THESE FACTORY CATS ARE CONSTUCTED OF
HEAVY GAUGE STEEL, AND SPECIALLY PLATED OR POWDER PAINTED TO PROTECT YOUR INVESTMENT.
THE TANKS HAVE EXTRA THICK WALLS, QUALITY INSERTS, AND "THROUGH TUBES" FOR STRENGTH. STEEL
BUMPERS PROTECT THE SCRUBHEAD AND FRONT END FROM COLLISION DAMAGE. THE CORNER
ROLLERS ARE POLYURETHANE, AND TALL TO DISPERSE THE FORCE OF IMPACT WITHOUT LEAVING
MARKS ON YOUR WALLS. THE WHOLE MACHINE IS PUT TOGETHER WITH STAINLESS STEEL FASTENERS TO
HELP PROLONG THE LIFE AND DURABILATY OF YOUR MACHINE.

chadv 11/23/2005 9:54:13 AM

 TABLE OF CONTENTS
MACHINE INFORMATION FORM PAGE 1
WARRANTY REGISTRATION FORM PAGE 2 PARTS BREAKDOWN ILLUSTRATION
MACHINE SPECIFICATIONS PAGE 3 SOLUTION SYSTEM PAGE 23-24
COMMON WEAR PARTS PAGE 4 RECOVERY SYSTEM PAGE 25-26
SAFETY MESSAGES PAGE 5 FRAME TOP PAGE 27-28
!!SAFETY PRECAUTIONS!! PAGE 6 FRAME BOTTOM PAGE 29-30
MACHINE FEATURES AND CONTROLS PAGE 7-8 DOOR WIPER/ROLLER ASSEMBLY PAGE 31-32
MACHINE SETUP PAGE 9-10 STEERING /TRACTION ASSEMBLY PAGE 33-34
OPERATION PAGE 11-12 ACTUATOR SLIDE ASSEMBLY PAGE 35-36
CHARGING BATTERIES PAGE 13 DISK SCRUBHEAD ASSEMBLY PAGE 37-38
MAINTENANCE PAGE 14 CYLINDRICAL DECK ASSEMBLY PAGE 39-40
STORING MACHINE PAGE 14 CYLINDRICAL MECHANICAL PAGE 41-42
PREVENTATIVE MAINTENANCE RECORDS PAGE 15-16 SQUEEGEE ASSEMBLY PAGE 43-44
LCD MENU DISPLAY PAGE 17 CENTRAL COMMAND II COMPONENTS PAGE 45-46
TOUBLESHOOTING CENTRAL COMMAND PAGE 18-19
TROUBLESHOOTING PAGE 20-21
MACHINE PARTS PAGE 22-40

MACHINE INFORMATION
PLEASE FILL THIS AREA OUT AT THE TIME OF INSTALLATION FOR FUTURE REFERENCE.

MODEL NUMBER_____________________________________________________________

SERIAL NUMBER:______________________________________________________________

INSTALLATION DATE:___________________________________________________________

INSTALLING DEALER:__________________________________________________________

DEALER CONTACT: ___________________________________________________________

ADDRESS:____________________________________________________________________

CITY, STATE, ZIP: ______________________________________________________________

PHONE NUMBER:_____________________________________________________________

THIS OPERATOR AND PARTS MANUAL SHOULD BE CONSIDERED A PERMANENT PART OF THE UNIT AND SHOULD
REMAIN WITH THE UNIT AT ALL TIMES. THIS OPERATOR AND PARTS MANUAL COVERS ALL THE TOMCAT 290/350
SERIES SCRUBBERS. YOU MAY FIND DESCRIPTIONS AND FEATURES THAT ARE NOT ON YOUR PARTICULAR MODEL.
THE INFORMATION AND SPECIFICATIONS INCLUDED IN THIS PUBLICATION WERE IN EFFECT AT THE TIME OF PRINTING.
MID-CENTRAL RESERVES THE RIGHT TO MAKE CHANGES WITHOUT NOTICE INCURRING ANY OBLIGATION.

TO REGISTER FOR WARRANTY, FAX YOUR WARRANTY REGISTRATION FORM TODAY!

chadv PAGE 1 11/23/2005 9:54:13 AM

 R.P.S. CORPORATION
P.O. BOX 368

ACTORYCA
RACINE, WI 53401
PHONE: 800-634-4060
FAX 866-901-3335
WWW.FACTORYCAT.COM

WARRANTY REGISTRATION FORM

***COMPLETE FORM IMMEDIATELY AND FAX BACK TO (886)-901-3335***

DEALER:________________________________________________________ SERIAL NUMBER:_________________

LOCATION (CITY, STATE):_________________________________________ INSTALL DATE:____________________

CUSTOMER:_____________________________________________________ HOUR METER:____________________

CONTACT:______________________________________________________ INSTALLED BY:___________________

ADDRESS:_______________________________________________________

CITY:_______________________STATE_______ZIP______________________

PHONE:_______________________ FAX:__________________________

FACTORY CAT MODEL NUMBER:_______________________________________

OPTIONS: 1.______________________________________ 4.______________________________________

2.______________________________________ 5.______________________________________

3.______________________________________ 6.______________________________________

PADS:_____________________________________________

BRUSHES:__________________________________________

SQUEEGEE SIZE:____________________________________

BUYER'S REPRESENTAVE HAS:

1. RECEIVED INSTRUCTION IN PROPER OPERATION OF THIS MACHINE.

2. RECEIVED OPERATOR'S MANUAL FOR THIS MACHINE.
3. BEEN MADE AWARE THAT ANY OPERATOR SHOULD READ THE MANUAL
BEFORE OPERATING THIS MACHINE.

DEALER REP. PRINT:___________________________________ SIGN:__________________________________

CUSTOMER PRINT:____________________________________ SIGN:__________________________________

chadv PAGE 2 11/23/2005 9:54:13 AM

 MODEL 290 350
BODY CONSTRUCTION/DIMENSIONS
TANK MATERIAL: POLY POLY
CHASSIS CONSTRUCTION: 3/16" STEEL 3/16" STEEL
REAR WHEELS: 12" X 5" 12" X 5"
FRONT WHEEL: 12" X 4" 12" X 4"
SIZE (L X W X H): 61" X 29" 61" X 35"
SQUEEGEE SIZE: 32", 35", OR 38" 35", 38", OR 45"
WEIGHT (WITHOUT BATTERIES): 750 LBS. 810 LBS.
WEIGHT (WITH BATTERIES): 1,260 LBS 1,320 LBS.

BRUSH/PAD SYSTEM
BRUSH/PAD DIAMETER (DISK): (2) 15.5 INCHES (2) 18 INCHES
DRIVE TO BRUSH (DISK): DIRECT DIRECT
SCRUBBING PATH (DISK): 29 INCHES 35 INCHES
BRUSH MOTOR POWER (DISK): (2) 1.0 HP (2) 1.0 HP
BRUSH MOTOR SPEED(DISK): 350 RPM 350 RPM
BRUSH SPEED (DISK): 350 RPM 350 RPM
BRUSH SIZE(CYLINDRICAL): (2) 26 INCHES (2) 28 INCH OR (2) 32 INCH
DRIVE TO BRUSH (CYLINDRICL): CHAIN CHAIN
SCRUBBING PATH (CYLINDRICAL): 26 INCHES 28 INCHES OR 32 INCHES
BRUSH MOTOR POWER (CYLINDRICAL): 2.0 HP 2.0 HP
BRUSH MOTOR SPEED (CYLINDRICAL): 800 RPM 800 RPM
BRUSH SPEED (CYLINDRICAL): 800 RPM 800 RPM
BRUSH DOWN PRESSURE: 0-200 LB. 0-250 LB.
BRUSH ADJUSTMENT: (5) AUTOMATIC SETTINGS (5) AUTOMATIC SETTINGS

SOLUTION SYSTEM
SOL. TANK CAP: 38 GAL 38 GAL
SOLUTION FLOW RATE: 0-1.75 GPM 0-1.75 GPM

RECOVERY SYSTEM
REC. TANK CAP: 40 GAL 40 GAL
VACUUM POWER (STANDARD): 1.0 HP 1.0 HP
VACUUM POWER (OPTIONAL): 2.0 HP 2.0 HP
DRAIN HOSE: 2.0 INCHES 2.0 INCHES
CLEANOUT DOOR (OPTIONAL) 5.0 INCHES 5.0 INCHES
WATERLIFT: 70 INCHES 70 INCHES

BATTERY SYSTEM
BATTERY AH RATING: (4) 396 AH (4) 396 AH
BATTERY RUN TIME: UP TO 6 HRS. UP TO 6 HRS.
CHARGER (AUTOMATIC): 36 AMP, 110 VOLT 36 AMP, 110 VOLT

DRIVE SYSTEM
TRANSAXLE DESCRIPTION: 2.0 HP, SEALED 2.0 HP, SEALED
SPEED CONTROL: 0-5 MPH 0-5 MPH
BRAKING SYSTEM: DYNAMIC BRAKING DYNAMIC BRAKING

PRODUCTIVITY
SCRUBBING WIDTH:
29 INCHES 35 INCHES
SCRUBBING RATE/HOUR (NORMAL):
35,000 FT/HR 45,000 FT/HR
SCRUBBING RATE/HOUR (MAXIMUM):
47,000 FT/HR 58,000 FT/HR

WARRANTY
PARTS: 3 YEARS 3 YEARS
LABOR: 1 YEAR 1 YEAR
TANKS: 10 YEARS 10 YEARS

chadv PAGE 3 11/23/2005 9:54:13 AM

 COMMON WEAR PARTS

MODEL MODEL MODEL MODEL

ITEM 290-D 290-C 350-D 350-C
BRUSH TYPE DISK CYLINDRICAL DISK CYLINDRICAL
BRUSHES
SUPER-GRIT 15-421SS NA 18-421SS NA
TOUGH-GRIT 15-421S 25-521S 18-421S 32-521S
MIDI-GRIT 15-421C 25-521C 18-421C 32-521C
LIGHT-GRIT 15-421PS 25-521PS 18-421PS 32-521PS
POLY (.028) 15-421P 25-521P 18-421P 32-521P
NYLON (.016) 15-421N 25-521N 18-421N 32-521N
TAMPICO 15-421T 25-521T 18-421T 32-521T
PAD DRIVER 15-421D NA 18-421D NA
EXTRA PAD DRIVER RETAINING CLIP: 40-433
BRUSH REPAIR KIT: 40-423 REPLACEMENT LOCATING CLIP FOR ALL DISK BRUSHES

PADS
SUPER BLACK 15-422BB NA 18-422BB NA
BLACK 15-422B NA 18-422B NA
BROWN 15-422BR NA 18-422BR NA
GREEN 15-422G NA 18-422G NA
BLUE 15-422BL NA 18-422BL NA
RED 15-422R NA 18-422R NA
WHITE 15-422W NA 18-422W NA

SQUEEGEE KITS SIZE GUM RUBBER NEOPRENE LINATEX

32" 22-770G 22-770N 22-770L
35" 25-770G 25-770N 25-770L
38" 28-770G 28-770N 28-770L
45" 290-770G 290-770N 290-770L

KIT INCLUDES: (1) REAR BLADE, (1) FRONT BLADE, AND (2) BACKUP WHEELS WITH HARDWARE

NOTE: IT IS STAMPED INTO THE TOP OF THE SQUEEGEE BLANK, ON 32", 35", 38", AND 45" SQUEEGEES.

MODEL 290: HAS A 38" SQUEEGEE UNLESS OTHER SIZE IS SPECIALLY ORDERED AT TIME OF PURCHASE
MODEL 350: HAS A 45" SQUEEGEE UNLESS OTHER SIZE IS SPECIALLY ORDERED AT TIME OF PURCHASE

NOTE: THE 32" AND 35" SQUEEGEES ARE DESIGNED FOR NARROW ISLES AND MAY NOT HAVE THE
SAME WATER CONTROL AROUND TIGHT TURNS AS THE LARGER SQUEEGEES.

SOAP
HEAVY DUTY DEGREASER
CITRUS
FREEZER
TIRE MARK REMOVER

CALL YOUR LOCAL DEALER FOR MORE SOAP INFORMATION

chadv PAGE 4 11/23/2005 9:54:13 AM

 SAFETY MESSAGES
YOUR SAFETY, AND THE SAFETY OF OTHERS, IS VERY IMPORTANT, AND OPERATING THIS UNIT
SAFELY IS AN IMPORTANT RESPONSIBILITY.

TO HELP YOU MAKE INFORMED DECISIONS ABOUT SAFETY, WE HAVE PROVIDED

OPERATING PROCEDURES AND OTHER SAFETY INFORMATION IN THE MANUAL. THIS
INFORMATION INFORMS YOU OF POTENTIAL HAZARDS THAT COULD HURT YOU OR OTHERS.

IT IS NOT PRACTICAL OR POSSIBLE TO WARN YOU OF ALL THE HAZARDS ASSOCIATED WITH
OPERATING THIS UNIT. YOU MUST USE YOUR OWN GOOD JUDGEMENT.

THIS IS INTENDED FOR COMMERCIAL USE. IT IS DESIGNED TO BE USED ON HARD FLOORS IN

AN INDOOR ENVIRONMENT, WITH THE RECOMMENDED PADS OR BRUSHES.

1. DO NOT OPERATE UNIT:

UNLESS TRAINED AND AUTHORIZED.
UNLESS OPERATOR MANUAL IS READ AND UNDERSTOOD.
IF UNIT IS NOT PROPER CONDITION.

2. WHEN OPERATING UNIT:

REMOVE LOOSE OBJECTS FROM THE FLOOR THAT MAY BE PROJECTED FROM
THE REVOLVING BRUSHES.
KEEP HANDS AND FEET AWAY FROM REVOLVING BRUSHES.
DO NOT OPERATE MACHINE WHERE FLAMMABLE LIQUIDS ARE PRESENT.
USE EXTREME CAUTION WHEN MANUEVERING.

3. BEFORE LEAVING:

MAKE SURE MACHINE IS TURNED OFF.

STOP ON LEVEL SURFACES.
DISCONNECT BATTERIES.

4. BEFORE SERVICING:

STOP ON LEVEL SURFACE, AND SECURE MACHINE.

DISCONNECT BATTERIES.

chadv PAGE 5 11/23/2005 9:54:13 AM

 !! SAFETY PRECAUTIONS!!
WARNING: HAZARDOUS VOLTAGE. SHOCK, BURNS WARNING : ALWAYS USE THE CHARGER PROVIDED
OR ELECTROCUTION CAN RESULT. ALWAYS DISCON- BY THE MANUFACTURER TO CHARGE THE MACHINE.
NECT THE BATTERIES BEFORE SERVICING MACHINE. IT IS AN AUTOMATIC CHARGER, SPECIFICALLY
DESIGNED TO CHARGE AT THE APPROPRIATE RATE.
IF YOU MUST USE A DIFFERENT CHARGER,
WARNING: BATTERIES EMIT HYDROGEN GASES, DISCONNECT THE BATTERIES BEFORE CHARGING.
EXPLOSION OR FIRE CAN RESULT. KEEP SPARKS AND THIS WILL PREVENT DAMAGE TO THE ELECTRONIC
OPEN FLAMES AWAY. SPEED CONTROLLER.

WARNING: CHARGE UNIT IN A WELL VENTILATED AREA, WARNING: UNDERSTAND THE DYNAMIC BRAKING
AND KEEP BATTERY COMPARTMENT OPEN WHEN SYSTEM BEFORE YOU OPERATE THE MACHINE ON
CHARGING. EXPLOSION OR FIRE COULD RESULT. RAMPS. MACHINE DOES NOT COAST. RELEASING
THE FOOTPEDAL WILL AUTOMATICALLY APPLY
BRAKING FORCE, AND STOP THE MACHINE.
WARNING: BATTERY ACID CAN CAUSE BURNS.
WEAR PROTECTIVE EYE WEAR AND GLOVES WHEN
SERVICING BATTERIES. WARNING: DO NOT PARK THE MACHINE ON
RAMPS OR SLOPES. THE MACHINE HAS A PARKING
BRAKE, BUT IT IS RECOMMENDED THAT IT IS ALWAYS
WARNING: DO NOT STORE OUTDOORS OR PRESSURE PARKED ON LEVEL GROUND.
WASH. PREVENT FROM GETTING ELECTRONIC
COMPONENTS WET.
WARNING: DO NOT OPERATE THE MACHINE IF
ANY PARTS HAVE BEEN REMOVED OR DAMAGED.
WARNING: THE USE OF PARTS AND SOLUTIONS OTHER
THAN RECOMMENDED BY THE MANUFACTURER MAY
CAUSE DAMAGE OR ENDANGER PEOPLE. WARNING: DO NOT REMOVE, PAINT OVER, OR
DESTROY WARNING DECALS. IF WARNING DECALS
BECOME DAMAGED, THEY MUST BE REPLACED.
WARNING: DRESS SAFELY. DO NOT WEAR RINGS
OR METAL WRIST WATCHES WHILE WORKING ON THIS
MACHINE. THEY CAN CAUSE AN ELECTRICAL SHORT, WARNING: DO NOT OPERATE MACHINE IN
WHICH, CAN CAUSE SERIOUS BURNS. DO NOT WORK UNSAFE CONDITION. IF THE MACHINE IS IN NEED OF
ON THIS MACHINE WHILE WEARING A TIE, SCARF OR REPAIR OR IS IN ANY WAY UNSAFE TO OPERATE,
OTHER LOOSE, DANGLING NECKWARE OR CLOTHING. THE MATTER SHOULD BE REPORTED IMMEDIATELY
THESE LOOSE ITEMS CAN TANGLE IN THE ROTATING TO THE SHIFT SUPERVISOR. DO NOT OPERATE THE
PARTS AND CAUSE SERIOUS INJURY OR EVEN DEATH. MACHINE UNTIL IT IS RETURNED TO PROPER
OPERATING CONDITION.

WARNING: DO NOT USE THE MACHINE AS A STEP

LADDER OR CHAIR. WARNING: THIS MACHINE MUST ONLY BE
OPERATED BY TRAINED OPERATOR. AS PART OF HIS
OR HER TRAINING, THEY MUST READ THIS MANUAL
WARNING: ONLY OPERATE THIS MACHINE FROM THOROUGHLY. IF EXTRA COPIES ARE NEEDED,
THE OPERATORS SEAT. IT WAS NOT DESIGNED TO CONTACT YOUR LOCAL DEALER.
CARRY PASSENGERS.

WARNING: ALWAYS TURN OFF THE MACHINE,

WARNING: DO NOT OPERATE THIS MACHINE ON RAMPS BEFORE LEAVING IT UNATTENDED.
OR UNEVEN SURFACES. WHEN CLIMBING A RAMP,
ALWAYS DRIVE THE MACHINE IN FORWARD STRAIGHT
UP OR DOWN THE RAMP. NEVER DRIVE ACROSS THE WARNING: DO NOT OPERATE OVER ELECTRICAL
INCLINE. DO NOT BACK DOWN OR TURN ON RAMPS! FLOOR OUTLETS. MAY RESULTS IN SERIOUS INJURY.

chadv PAGE 6 11/23/2005 9:54:13 AM

 MACHINE CONTROLS AND FEATURES
1 2 9 10

4 17

FIGURE 1. FIGURE 2.

5 6 7 8 11 12 13 14 15 16
18 19

22
20

FIGURE 3. FIGURE 4.

21 23 24 25
26 27 28 29 40 39 37 36
30 34
31 35
38

32

41
33 42
FIGURE 5 FIGURE 6A. 43 FIGURE 6B.

chadv PAGE 7 11/23/2005 9:54:13 AM

 CONTROLS AND FUNCTIONS
SEE FIGURES (1-6B) ON PAGE 7
SEE FIGURE 1
1. STEERING WHEEL: STEERS THE MACHINE.
2. ADJUSTABLE SEAT WITH ARM RESTS: YOUR MACHINE IS EQUIPPED WITH AN ADJUSTABLE SEAT WITH ARM RESTS FOR COMFORT
3. RECOVERY TANK: HOLDS UP TO 40 GALLONS OF DIRTY WATER RECOVERED BY THE MACHINE.
4. SOLUTION TANK: HOLDS UP TO 38 GALLONS OF CLEAN WATER AND SOLUTION DETERGENT.
5. HEAD LIGHT: HELPS YOU SEE IN LOW LIGHT AREAS AND TO WARN ONCOMING TRAFFIC.
6. FRONT DRIVE WHEEL: DRIVES AND STEERS MACHINE.
7. BUMPER ROLLERS: HELPS PREVENT DAMAGE TO MACHINE AND OBJECTS THAT YOU MAY DRIVE CLOSE TO WHILE CLEANING.
8. DOOR WIPER: GOES UP AND DOWN WITH SCRUB DECK TO KEEP WATER FROM SPLASHING OUT OF MACHINE.

SEE FIGURE 2.
9. SEAT ADJUSTMENT: PERMITS THE SEAT TO BE ADJUSTED FORWARD AND BACKWARDS FOR OPERATORS COMFORT.
10. HORN BUTTON: SOUNDS THE HORN FOR WARNING ONCOMING TRAFFIC.
11. SOLUTION LEVEL INDICATOR: SHOWS OPERATOR THE PRECISE LEVEL OF CLEANING DETERGENT IN THE TANK.
12. SOLUTION FLOW CONTROL: USED TO MODULATE THE SOLUTION FLOW (GPM).
13. NON SLIP FLOOR PLATE: HELPS PREVENT SLIPPING WHILE GETTING ON AND OFF OF MACHINE.
14. FOOT PEDAL : CONTROLS THE ACCELERATION AND DECELERATION OF THE MACHINE.
15. CHARGER PORT: RED 50 USED TO RECEIVE CHARGER INPUT. NOTE: ONLY USE CHARGER PROVIDED.
16. ADJUSTABLE STEERING: FOUR SETTINGS FOR OPERATOR COMFORT AND EASE OF ENTRY.
17. CIRCUIT BREAKER: 50 AMP RESETABLE CIRCUIT BREAKER.

SEE FIGURE 3
18. RECOVERY DRAIN HOSE: ALLOWS FOR CONTROLLED DRAINING OF THE RECOVERY TANK.
19. VACUUM HOSE: VACUUMIZES SQUEEGEE . NOTE: KEEP FREE AND CLEAR OF BLOCKAGE.
20. VACUUM HOSE: MAIN VACUUM HOSE FROM VACUUM TO RECOVERY TANK.
21. SQUEEGEE BLADE: SQUEEGEES WATER TO BE RECOVERED BY THE VACUUM HOSE.

SEE FIGURE 4
22. SIDE DOOR: PROVIDES EASY ACCESS TO SCRUB DECK.
23. SCRUB DECK: MAIN COMPONENTS THAT SCRUB AND CLEAN FLOORS.
24. REAR WHEELS: NON MARKING REAR TIRES
25. SQUEEGEE BLADE PROTECTION WHEELS: HELP PROTECT THE SQUEEGEE WHEN CLEANING CLOSE TO OBJECTS.

SEE FIGURE 5
26. RECOVERY ACCESS DOOR: USED FOR FLUSHING OUT RECOVERY TANK WITH FRESH WATER.
27. BATTERIES: YOUR MACHINE IS EQUIPPED WITH FOUR (6 VOLT DEEP CYCLE 396 AMP HOUR BATTERIES)
28. FOAM PROTECTION SCREEN: USED TO PROTECT VACUUM MOTOR FROM DEBRIS.
29. BATTERY ACCESS LID: USED TO VENT BATTERIES DURING CHARGING, OR TO ACCESS BATTERIES FOR SERVICE.

SEE FIGURES 6A AND 6B

30. HIGH WATER RECOVERY LIGHT: INDICATES WHEN THE RECOVERY TANK IS NEARLY FULL.
31. LCD SCREEN: LISTS FUNCTIONS AND SETTING OF THE MACHINE. (SEE PAGES 17-19)
32. SQUEEGEE SWITCH: RAISES AND LOWERS THE SQUEEGEE.
33. ONE TOUCH BUTTON: ACTIVATES BRUSHES, SQUEEGEE, VACUUM SYSTEM, AND SOLUTION FLOW SIMUTANEOUSLY.
34. LOW WATER SOLUTION LIGHT: INDICATES WHEN THE SOLUTION TANK IS DOWN TO 5 GALLONS.
35. MENU CONTROL: SCROLLS THROUGH DIFFERENT OPTIONS ON THE LCD DISPLAY.
36. KEY SWITCH: TURNS THE MAIN POWER ON AND OFF.
37. OPTIONAL RECYLING SWITCH: TURNS ON THE RECYCLING PUMP. (GREEN)
38. SCRUB DECK DOWN PRESSURE SWITCH: CONTROLS THE PRESSURE PUT ON THE SCRUB DECK.
39. VACUUM WAND SWITCH: TURNS ON THE VACUUM MOTOR. (WHITE)
40. OPTIONAL SPRAY JET: TURNS ON THE SPRAY JET PUMP. (BLUE)
41. SCRUB DECK SWITCH: RAISES AND LOWERS THE SCRUB DECK.
42. SOLUTION SWITCH: OPENS AND CLOSES THE SOLUTION VALVE. GLOWS BLUE WHEN OPEN.
43. FORWARD/REVERSE SWITCH: CONTROLS THE DIRECTION OF THE TRACTION MOTOR. (RED)

chadv PAGE 8 11/23/2005 9:54:13 AM

 MACHINE SETUP
UNCRATING MACHINE ATTACHING SQUEEGEE
1. LOWER THE SQUEEGEE MOUNTING PLATE BY
CAREFULLY CHECK THE CRATE FOR ANY SIGNS OF DEPRESSING THE SQUEEGEE SWITCH TO THE DOWN
DAMAGE. BATTERIES ARE IN THE UNIT. POSITION. (SEE FIGURE 8.)

TO UNCRATE THE MACHINE, REMOVE BANDING FROM

AROUND THE CRATE. TAKE OFF THE TOP AND SIDES
AND DISPOSE OF PROPERLY. REMOVE BANDING
FROM MACHINE. REMOVE THE CHOCKS AROUND
THE DRIVE WHEELS. FOLD DOWN RAMP, AND DRIVE
MACHINE OFF OF THE BASE. NOTIFY THE CARRIER
IMMEDIATELY IF CONCEALED DAMAGE IS DISCOVERED.

CONNECTING BATTERIES
YOUR MACHINE IS EQUIPPED WITH (FOUR) 6 VOLT,
DEEP CYCLE, 396 AMP HOURS BATTERIES, WHICH FIGURE 8.
FORM A 24 VOLT SYSTEM. MAXIMUM BATTERY
DIMENSIONS ARE 7"W X 15"L X 15"H.
2. LOOSEN THE TWO WING NUTS ON THE SQUEEGEE
1. TURN ALL SWITCHES TO THE OFF POSITION AND AND SLIDE THEM INTO THE SLOTS IN THE SQUEEGEE
REMOVE KEY. MOUNTING PLATE. THE SQUEEGEE TRAIL WHEELS
SHOULD FACE OUTWARD. (SEE FIGURE 9.)
2. HINGE OPEN THE BATTERY ACCESS LID TO
ACCESS THE BATTERY COMPARTMENT. 3. TIGHTEN THE TWO WINGNUTS, AND CONNECT
VACUUM HOSE FROM THE MACHINE TO THE
3. ALL OF THE FOUR BATTERY CABLES ARE SQUEEGEE. (SEE FIGURE 9.)
CONNECTED TO THE BATTERIES. LOCATE ANY
LOOSE ONES AND CONNECT TO THE OPEN 4. YOU MAY HAVE TO ADJUST THE SQUEEGEE PITCH,
TERMINAL. TIGHTEN WITH 9/16" WRENCH. BY USING THE PITCH ADJUSTMENT. (SEE FIGURE 9.)
(SEE FIGURE 7.)

4. TURN ON MAIN POWER SWITCH AND CHECK

THE BATTERY CONDITION METER TO ENSURE
CORRECT INSTALLATION. CHARGE BATTERIES IF
NEEDED. (SEE: BATTERY CHARGING)

FIGURE 7 FIGURE 9.

chadv PAGE 9 11/23/2005 9:54:13 AM

 ATTACHING ATTACHING
DISK BRUSHES CYLINDRICAL BRUSHES
1. TURN ON MACHINE POWER 1. TURN ON MACHINE POWER
2. RAISE THE SCRUB DECK BY DEPRESSING THE 2. RAISE THE SCRUB DECK BY DEPRESSING THE
BRUSH SWITCH TO THE UP AND OFF POSITION BRUSH SWITCH TO THE UP AND OFF POSITION
AND TURN MACHINE POWER BACK OFF. AND TURN MACHINE POWER BACK OFF.
(SEE FIGURE 10.) (SEE FIGURE 10.)
3. OPEN THE SIDE DOOR TO ACCESS CYLINDRICAL
SCRUB DECK
4. UNSCREW THE THREE WINGNUTS ON THE BRUSH
ACCESS DOOR AND REMOVE THE DOOR.
(SEE FIGURE 13.)

FIGURE 10.

3. OPEN SIDE DOOR TO ACCESS SCRUB DECK

4. SELECT THE CORRECT PADS OR BRUSHES THAT
BEST MEET YOUR CLEANING APPLICATION.
CONSULT YOUR LOCAL DEALER FOR ASSISTANCE. FIGURE 13.
5. PAD INSTALLATION ATTACH PADS TO PAD
DRIVERS BEFORE CONNECTING DRIVERS TO 5. SLIDE THE BRUSHES IN ONE AT A TIME. WHEN YOU
MOTOR HUB. GET THE BRUSH ON THE DRIVER SPIN IT WITH YOUR
6. ATTACH BRUSHES OR PADS TO MOTOR HUBS. HAND UNTIL YOU FEEL IT ENGAGE AND DROP IN.
SQUEEZE THE SCISSOR LOCKING DEVICE AND LIFT (SEE FIGURE 14.)
BRUSH UP ON TO THE MOTOR DRIVE HUB. MAKE
SURE THE SCISSORS CLOSE AND LOCK ONCE THE
BRUSHES ARE ON. (SEE FIGURE 11.)

FIGURE 14.
6. WHEN BOTH BRUSHES ARE ENGAGED REPLACE
THE BRUSH ACCESS DOOR AND TIGHTEN IT BACK
FIGURE 11.
DOWN WITH THE WINGNUTS. (SEE FIGURE 15.)
7. LIFT UP ON THE WIPERS FIRST TO CLOSE SIDE
DOOR AND DEPRESS THE LATCH UNTIL THE DOOR
IS SECURED. (SEE FIGURE 12.)

FIGURE 15.

7. LIFT UP ON THE WIPERS FIRST TO CLOSE SIDE

DOOR AND DEPRESS THE LATCH UNTIL THE DOOR
FIGURE 12. IS SECURED. (SEE FIGURE 12.)
***FOR CORRECT PAD APPLICATION , CALL YOUR LOCAL DEALER***
chadv PAGE 10 11/23/2005 9:54:13 AM
 OPERATION
PRE-CLEANING CHECK LIST ONE PASS SCRUBBING
STEPS: (SEE FIGURE 17.)

READ AND UNDERSTAND THE SAFETY SECTION ON

PAGE 5 AND 6 BEFORE OPERATING MACHINE. 1. TURN MACHINE ON WITH THE KEY SWITCH.

2. LOWER SQUEEGEE BY PRESSING THE SWITCH.

1. CHECK BATTERY CONDITION GAUGE ON
THE CENTRAL COMMAND II LCD SCREEN. 3. LOWER SCRUB HEAD TO THE FLOOR, USE THE
TO CHECK GAUGE PUSH MENU CONTROL TOP HALF (+) OF THE BRUSH SWITCH.
BUTTON UNTIL BATTERY GUAGE APPEARS.
MAKE SURE BATTERIES ARE FULLY CHARGED 4. TURN ON THE SOLUTION SWITCH AND ADJUST
BEFORE USING. THE SOLUTION LEVER TO THE DESIRED SETTING.

2. CHECK THE CONDITION OF PADS OR BRUSHES. 5. BEGIN SCRUBBING BY DEPRESSING THE

FOOT PEDAL SLOWLY AND THEN TO THE
3. CHECK THE CONDITION OF THE SQUEEGEE BLADES. SPEED REQUIRED, THE HEADLIGHT
SHOULD ILLUMINATE.
4. TRANSPORT THE MACHINE TO THE FILLING
STATION. RAISE THE SCRUBHEAD AND 6. ONCE THE MACHINE BEGINS TO MOVE,
SQUEEGEE WHEN TRANSPORTING. CHECK THE DOWN PRESSURE GAUGE. START
SCRUBBING AT THE #1 OR # 2 MARKS, DO NOT
5. TURN MACHINE OFF. USE THE #4 OR #5 MARKS WITHOUT
MANAGEMENTS APPROVAL.
6. OPEN SOLUTION FILL DOOR AT THE SIDE OF
THE MACHINE AND FILL THE TANK WITH UP 7. TO OPERATE MACHINE IN REVERSE,
TO 38 GALLONS OF CLEAN WATER. THE SIMPLY SWITCH THE REVERSE SWITCH TO
CLEAR TUBE AT THE FRONT OF THE MACHINE INDICATES THE REVERSE POSITION, BACK UP ALARM
THE AMOUNT OF WATER IN THE TANK. MAY SOUND AND YOUR REV SPEED IS SET
TO ROUGHLY 50% OF FORWARD.
7. ADD CLEANING CHEMICAL. USE THE PROPER
DILUTION RATIO INDICATED ON THE BOTTLE. 8. TO STOP THE MACHINE, LET OFF OF THE
FOOT PEDAL, AND THE MACHINE WILL
NOTE: USE ONLY NONFLAMMABLE COMMERCIAL STOP AUTOMATICALLY.
CLEANING CHEMICALS. YOUR AUTHORIZED
DISTRIBUTOR CAN ASSIST YOU IN SELECTING A 1 4 5
PROPER CHEMICAL.

2
4
3
7

FIGURE 16. FIGURE 17.

chadv PAGE 11 11/23/2005 9:54:13 AM

 OPERATING HINTS DRAINING RECOVERY TANK
1. OBSERVE THE AMOUNT OF SOLUTION THE MACHINE IS ALWAYS EMPTY RECOVERY TANK WHEN REFILLING THE
DISPENSING ON THE FLOOR AND ADJUST TO THE DESIRED SOLUTION TANK. TO DRAIN THE RECOVERY TANK, PERFORM THE
FLOW. TO INCREASE THE SOLUTION FLOW RATE, MOVE FOLLWING STEPS.
THE SOLUTION LEVER TO THE OPERATORS RIGHT. TO SHUT
THE SOLUTION OFF COMPLETELY, USE THE SWITCH, OR 1. REMOVE DRAIN HOSE FROM THE EXPANSION PLUG HOLDER
JUST RELEASE THE FOOT PEDAL. BY TUNING THE T-HANDLE COUNTER CLOCKWISE. OPEN THE TOP
"RECOVERY ACCESS LID" AND FLUSH OUT WITH WATER TO KEEP
2. KEEP AN EYE ON THE REC FULL LIGHT TO MAKE SURE TANK CLEAN. (SEE FIGURE 18.)
THERE IS NOT FOAMY BUILDUP IN THE RECOVERY TANK. IF
EXCESS FOAM BEGINS TO DEVELOP, POUR A
RECOMMENDED FOAM CONTROL SOLUTION INTO THE
RECOVERY TANK. FOAM IS USUALLY AN INDICATION OF
EXCESSIVE SOAP.

3. ALWAYS OPERATE AT LOWER SPEEDS WHEN SCRUBBING

AROUND WALLS AND OBJECTS. YOU SHOULD REDUCE THE
SPEED, TO MAINTAIN CONTROL WHEN TURNING.

4. IF SQUEEGEE STARTS TO STREAK, RAISE AND WIPE THE

BLADES WITH A CLEAN CLOTH. IF THE PROBLEM
CONTINUES, CHECK THE BLADES FOR WEAR OR DAMAGE,
AND ROTATE IF NEEDED. YOU NEED TO PRESWEEP BEFORE
SCRUBBING.
FIGURE 18.
5. CHANGE OR TURN OVER PADS WHEN DIRTY. ROTATE
THE SCRUB BRUSHES EVERY WEEK. 2. RINSE THE RECOVERY TANK AFTER EVERY USE. THIS WILL
PREVENT HEAVY BUILDUP ON THE BOTTOM OF THE TANK,
6. STAY CLEAR OF OBJECTS PROTRUDING FROM THE FOUL ODORS, AND CLOGGING OF THE DRAIN HOSE.
FLOOR, SUCH AS SOCKETS, GRATES, DIES, FOR THEY WILL
DAMAGE THE PADS AND SQUEEGEE BLADES. 3. ONCE TANK IS EMPTY, PUT DRAIN HOSE BACK ON THE
PLUG AND TIGHTEN BY TURNING THE T-HANDLE CLOCK WISE.
7. DURING BRIEF STOPS YOU DO NOT HAVE TO TURN
ANYTHING OFF, THE BRUSHES AND SOLUTION WILL
AUTOMATICALLY STOP WHEN THE FOOT PEDAL IS DRAINING SOLUTION TANK
RELEASED.
TO DRAIN LEFT OVER CLEANING SOLUTION FROM THE
8. ALWAYS KEEP AN EYE ON YOUR GAUGES. THEY LET SOLUTION TANK, PERFORM THE FOLLOWING STEPS.
YOU KNOW THE STATUS OF A PARTICULAR SYSTEM AT A (SEE FIGURE 19.)
GLANCE. IF YOUR BATTERY GAUGE IS READING LOW,
YOU MUST STOP IMMEDIATELY, AND RECHARGE. 1. ROTATE THE BLUE SOLUTION TANK DRAIN VALVE OUTWARDS.
RUNNING THE BATTERIES DEAD, WILL RESULT IN DAMAGE
TO THE BATTERIES. EXCESSIVE SCRUBBING PRESSURE WILL
BLOW A BREAKER.

9. WHEN YOU RUN OUT OF SOLUTION, RAISE THE BRUSHES,

AND CONTINUE TO VACUUM THE REMAINING WATER UNTIL
IT IS CONSUMED. THE SOLUTION SIGHT HOSE IS USED TO
INDICATE THE LEVEL OF DETERGENT REMAINING IN THE
TANK.

10. WHEN YOU ARE READY TO STOP, PICK UP THE

BRUSHES, TURN OFF THE SOLUTION SWITCH, PICK UP THE
SQUEEGEE, AND DRIVE THE MACHINE BACK TO THE
CHARGING AREA. BE SURE TO DRAIN BOTH TANKS BEFORE
STORING MACHINE.
FIGURE 19.

chadv PAGE 12 11/23/2005 9:54:13 AM

 BATTERY
CHARGING
CAUTION: THE FOLLOWING INSTRUCTIONS ARE 4. CHECK THE WATER LEVEL IN EACH BATTERY.
INTENDED FOR THE 24V CHARGER SUPPLIED WITH DO NOT CHARGE THE MACHINE UNLESS THE
THE MACHINE. DO NOT USE ANY OTHER WATER IS SLIGHTLY HIGHER THAN THE PLATES. IF
CHARGER WITH THIS MACHINE. NEEDED, ADD ENOUGH DISTILLED WATER TO JUST

CHARGER
SLIGHTLY COVER THE PLATES. DO NOT OVER FILL.
BATTERIES CAN OVERFLOW DURING CHARGING.
REPLACE CAPS BEFORE CHARGING.

SPECIFICATIONS 5. WITH THE RED CHARGER PLUG DISCONNECTED

FROM THE MACHINE, PLUG THE CHARGER
OUTPUT VOLTAGE OF 24 VOLTS. POWER CORD INTO A GROUNDED 110 VOLT
STANDARD WALL OUTLET.
OUTPUT CURRENT OF 36 AMPS MAX. (SEE FIGURE 21.)

INPUT VOLTAGE OF 110 VOLTS/60 HZ. 6. CONNECT THE RED CHARGER PLUG INTO THE
BATTERY CHARGING PORT LOCATED ON THE
AUTOMATIC SHUT OFF CIRCUIT. LOWER PORTION OF THE STEERING TOWER.

MADE FOR DEEP CYCLE BATTERIES.

DANGER: ALWAYS CHARGE BATTERIES IN A WELL

VENTILATED AREA. BATTERIES EMIT HYDROGEN
GAS. EXPLOSION OR FIRE CAN RESULT. KEEP
SPARKS AND FLAME AWAY. SHIELD EYES WHEN
SERVICING BATTERIES AND AVOID CONTACT WITH
BATTERY ACID. LEAVE ACCESS PANEL OPEN WHEN CHARGING!

1. TRANSPORT MACHINE TO A WELL VENTILATED

AREA FOR CHARGING.

2. TURN THE MACHINE OFF.

3. HINGE OPEN THE BATTERY ACCESS PANEL TO FIGURE 21.

EXPOSE THE BATTERIES. (SEE FIGURE 20.)
(CAUTION ALWAYS WEAR EYE PROTECTION WHEN
BATTERIES ARE EXPOSED) 7. THE CHARGER WILL AUTOMATICALLY BEGIN
CHARGING, AND AUTOMATICALLY SHUT OFF
WHEN FULLY CHARGED (CHECK GAUGE)

8. AFTER THE CHARGER HAS TURNED OFF, UNPLUG

THE RED CHARGER PLUG FROM THE MACHINE
AND DISCONNECT THE CHARGER FROM THE
WALL OUTLET.

9. RECHECK THE CELL LEVEL AFTER CHARGING. IF

NEEDED, ADD DISTILLED WATER UP TO THE
CORRECT LEVEL. BE CERTAIN TO REPLACE THE
CAPS SECURELY AND TO WIPE OFF THE TOP OF
THE BATTERIES WITH A CLEAN CLOTH.

FIGURE 20.

chadv PAGE 13 11/23/2005 9:54:13 AM

 MAINTENANCE
MONTHLY
DAILY MAINTENANCE MAINTENANCE
1. REMOVE AND CLEAN PADS OR BRUSHES. NEVER 1. CHECK SCRUB HEAD AND SQUEEGEE LIFTING CABLES FOR
USE SOILED PADS WHEN CLEANING. REPLACE WEAR AND SPRING TENSION.
PADS WHEN THEY BECOME PACKED WITH RESIDUE.
2. CHECK MACHINE FOR WATER LEAKS AND LOOSE NUTS AND
2. REMOVE AND CLEAN DEBRIS FROM THE FLOAT BOLTS.
SHUT-OFF SCREEN LOCATED INSIDE THE RECOVERY
TANK. 3. CHECK TO SEE IF BATTERY CABLES ARE TIGHTENED
(TIGHTEN IF NEEDED)
3. DRAIN AND RINSE TANKS THOROUGHLY INSPECT
VACUUM HOSE FOR ANY OBJECTS OBSTRUCTING 4. CHECK PARKING BRAKE
THE AIR FLOW.
5. CHECK CONDITION OF SCRUB DECK LIFTING CABLE.
4. RAISE SQUEEGEE AND WIPE BLADES WITH A CLEAN
CLOTH. STORE SQUEEGEE IN THE RAISED POSITION
TO PREVENT DAMAGE OR SETTING OF THE BLADES.

5. WIPE DOWN MACHINE IF NEEDED. USE A

NONABRASIVE, NON SOLVENT CLEANER, OR A
CLEAN DAMP CLOTH.

6. RECHARGE THE BATTERIES IF NEEDED.

WEEKLY YEARLY
MAINTENANCE MAINTENANCE
1. CHECK BATTERY WATER LEVEL IN EACH CELL OF THE 1. CALL YOUR LOCAL DEALER FOR YEARLY MAINTENANCE
BATTERIES, AND FILL AS NEEDED. ALWAYS USE
DISTILLED WATER TO REFILL BATTERIES. BATTERIES
SHOULD BE FILLED APPROXIMATELY 3/4" TO 1" ABOVE
THE PLATES. OVERFILLING WILL CAUSE THE BATTERIES
TO LEAK DURING CHARGING. THE CHARGING
STORING MACHINE
PROCESS CREATES GAS BUBBLES INSIDE THE BATTERY,
WHICH EFFECTIVELY INCREASES THE VOLUME OF THE 1. BE SURE TO FLUSH THE TANKS OUT COMPLETELY, AND TO
ELECTROLITE. DRAIN ALL WATER FROM THE MACHINE.

2. CLEAN BATTERY TOPS TO PREVENT CORROSION. 2. REMOVE THE RECOVERY TANK LID TO PROMOTE AIR
CIRCULATION.
3. ROTATE BRUSHES. ROTATE THE LEFT TO THE RIGHT
AND RIGHT TO LEFT. ON CYLINDRICAL MODELS 3. RAISE BRUSHES AND SQUEEGEE.
FROM FRONT TO BACK, OR END TO END IF USING
DIFFERENT MATERIALS.

chadv PAGE 14 11/23/2005 9:54:13 AM

 PREVENTATIVE MAINTENANCE RECORDS
USE THIS FORM TO MAKE COPIES FOR YOUR INTERNAL RECORDS

PREVENTATIVE MAINTENANCE CHECKED NOTE

ROTATE BRUSHES _____________ ____________________________________

ROTATE SIDE BROOMS _____________ ____________________________________
DRAIN SOLUTION TANK _____________ ____________________________________
FLUSH SOLUTION SYSTEM _____________ ____________________________________
CLEAN SOLUTION SCREEN _____________ ____________________________________
DRAIN RECOVERY TANK _____________ ____________________________________
FLUSH RECOVERY TANK _____________ ____________________________________
CLEAN VACUUM SCREEN _____________ ____________________________________
ROTATE REAR SQUEEGEE BLADE _____________ ____________________________________
CHECK BATTERY WATER LEVEL _____________ ____________________________________
CHECK BATTERY VOLTAGE _____________ ____________________________________
CHECK CHARGER CONDITION _____________ ____________________________________
CHECK BATTERY CONNECTIONS _____________ ____________________________________
CHECK CHEMICAL LEVEL _____________ ____________________________________
CHECK MACHINE PERFORMANCE _____________ ____________________________________
SCRUBBING POWER _____________ ____________________________________
VACUUM POWER _____________ ____________________________________
CONTROLS WATER ON TURNS _____________ ____________________________________
GAUGES AND CONTROLS _____________ ____________________________________
CHECK WHEEL TRACTION _____________ ____________________________________

OTHER:__________________________ _____________ ___________________________________

OTHER:__________________________ _____________ ___________________________________

PAST HOUR METER READING: ___________________________________

CURRENT HOUR METER READING: ___________________________________

AVERAGE WEEKLY USAGE: ___________________________________

TECHNICIAN PRINT:_____________________________________________

TECHNICIAN SIGNATURE:________________________________________ DATE:_________________

MANAGER SIGNATURE:_________________________________________ DATE:_________________

chadv PAGE 15 11/23/2005 9:54:13 AM

 PREVENTATIVE MAINTENANCE RECORDS
USE THIS FORM TO MAKE COPIES FOR YOUR INTERNAL RECORDS

PREVENTATIVE MAINTENANCE CHECKED NOTE

ROTATE BRUSHES _____________ ____________________________________

ROTATE SIDE BROOMS _____________ ____________________________________
DRAIN SOLUTION TANK _____________ ____________________________________
FLUSH SOLUTION SYSTEM _____________ ____________________________________
CLEAN SOLUTION SCREEN _____________ ____________________________________
DRAIN RECOVERY TANK _____________ ____________________________________
FLUSH RECOVERY TANK _____________ ____________________________________
CLEAN VACUUM SCREEN _____________ ____________________________________
ROTATE REAR SQUEEGEE BLADE _____________ ____________________________________
CHECK BATTERY WATER LEVEL _____________ ____________________________________
CHECK BATTERY VOLTAGE _____________ ____________________________________
CHECK CHARGER CONDITION _____________ ____________________________________
CHECK BATTERY CONNECTIONS _____________ ____________________________________
CHECK CHEMICAL LEVEL _____________ ____________________________________
CHECK MACHINE PERFORMANCE _____________ ____________________________________
SCRUBBING POWER _____________ ____________________________________
VACUUM POWER _____________ ____________________________________
CONTROLS WATER ON TURNS _____________ ____________________________________
GAUGES AND CONTROLS _____________ ____________________________________
CHECK WHEEL TRACTION _____________ ____________________________________

OTHER:__________________________ _____________ ___________________________________

OTHER:__________________________ _____________ ___________________________________

PAST HOUR METER READING: ___________________________________

CURRENT HOUR METER READING: ___________________________________

AVERAGE WEEKLY USAGE: ___________________________________

TECHNICIAN PRINT:_____________________________________________

TECHNICIAN SIGNATURE:________________________________________ DATE:_________________

MANAGER SIGNATURE:_________________________________________ DATE:_________________

chadv PAGE 16 11/23/2005 9:54:13 AM

 LCD SCREEN MENU DISPLAYS
2 SCREEN # 1 1 SCREEN # 2
1 3

(FIGURE 22.) (FIGURE 23.)

4 3 4 5
SCREEN #3 SCREEN #1 W/ERROR CODE
1 5 1

7
(FIGURE 24.) (FIGURE 25.)

9 8
*** USE GREEN MENU SELECTION BUTTON ON CONTROL PANEL TO CHANGE SCREENS***

FIGURES 22-25.

1. BATTERY LEVEL INDICATOR - INDICATES THE ENERGY LEVEL REMAINING IN THE BATTERIES.
(SHOWN ON ALL MENU DISPLAYS)

2. SCRUBBING DECK DOWN PRESSURE GAUGE - SETS THE DOWN PRESSURE ON THE BRUSHES. (SEE FIGURE 22.)

3. VACUUM ON - TELLS YOU WHEN THE VACCUM IS ON. (SEE FIGURES 22. AND 23)

4. SCRUBBING MOTORS ON - TELLS YOU WHEN THE BRUSH MOTORS ARE RUNNING. (SEE FIGURES 22. AND23.)

5. KEY SWITCH HOUR METER - TELLS YOU THE TOTAL HOURS THE MACHINE HAS ON. (SEE FIGURES 23. AND 24.)

6. SCRUBBING BRUSH HOUR METER - TELLS YOU THE TOTAL HOURS THE BRUSH MOTORS HAVE BEEN USED.
(SEE FIGURE 24.)

7. TRANSPORT HOUR METER - TELLS YOU THE TOTAL HOURS THE DRIVE SYSTEM HAS BEEN USED. (SEE FIGURE 24.)

8. ERROR WARNING SYMBOL - INDICATES WHEN THERE HAS BEEN A DIAGNOSTIC CODE ERROR. (SEE FIGURE 25.)

9. DIAGNOSTIC CODE - WHEN THE MACHINE HAS DETECTED AN ERROR IT WILL DISPLAY THE WARNING SYMBOL
AND A DIAGNOSTIC CODE WHICH TELL YOU WHATS WRONG. (SEE FIGURE 25.)

( FOR COMMAND ERROR CODES AND DISCRIPTIONS SEE PAGE 18. AND 19.)

chadv PAGE 17 11/23/2005 9:54:13 AM

 TROUBLESHOOTING CENTRAL COMMAND
NOTE: THIS MACHINE IS OPERATED BY A SOPHISTICATED ELECTRONIC "BRAIN" THAT HAS MANY FAIL-SAFES WITHIN IT. THE
BRAIN SELF-ANALYZES PROBLEMS AND FLASHES A FOUR-DIGIT NUMERIC CODE OF WHAT IS WRONG IN THE LCD WINDOW.

MOST OF THESE CODES REQUIRE A TECHNICIAN'S ATTENTION. YOU SHOULD NOT ATTEMPT REPAIRS YOU ARE
UNCOMFORTABLE WITH, ESPECIALLY IF YOU ARE NOT USED TO WORKING ON ELECTRONICS.

THE COMPLETE LIST OF CODES IS PUBLISHED IN THE SIMPLIFIED ELECTRONIC TROBLESHOOTING MANUAL, WHICH IS
AVAILABLE TO TECHNICAL PEOPLE. HOWEVER, WE HAVE INCLUDED THE BASIC CODES THAT YOU CAN USUALLY RESOLVE
YOURSELF.

1. 1E03 AND 1E04 ERROR. CHECK THE SMALL SAFETY

SWITCH NEXT TO THE RED PLUG BELOW THE DASHBOARD.
THIS SWITCH WILL TURN OFF THE TRACTION DRIVE AND
BRUSHES AS A SAFETY FEATURE WHILE THE CHARGER IS
PLUGGED IN. THE SWITCH MAY BE STUCK, OR THE PLUG
TWISTED AT AN ANGLE, ENGAGING THE SWITCH. THIS
CODE WILL ALSO FLASH IF THE WIRING BECOMES VERY
WET. IN THIS CASE, EITHER WAIT UNTIL THE WIRING DRIES
OUT, OR CALL A TECHNICIAN.
(FIGURE 26.)

2. 7601 AND 7602 ERROR. PAD CURRENT OVER LOAD.

THIS CAN CAN OCCUR WHEN THE PADS HIT A BUMP IN THE
FLOOR. TO RESTART THE PADS, TURN OFF THE KEY AND
TURN IT ON AGAIN. TO AVOID THIS ERROR, EITHER SLOW
DOWN ON BUMPY PARTS OF THE FLOOR, OR REDUCE
DOWNPRESSURE ON THE PADS.

(FIGURE 27.)

3. 1600 ERROR. VOLTAGE EXCEEDS THE MAXIMUM.

EITHER THE BATTERIES ARE MIS-WIRED, OR THE CHARGER IS
STILL PLUGGED INTO THE MACHINE.

(FIGURE 28.)

4. 7700, 7701, 7702, AND 7703 ERROR. THE VACUUM

MOTOR HAS EXCEEDED THEIR AUTHORIZED POWER LIMITS.
TURN OFF KEY AND TURN ON AGAIN TO CLEAR.

(FIGURE 29.)

chadv PAGE 18 11/23/2005 9:54:13 AM

 TROUBLESHOOTING CENTRAL COMMAND

5. 7900 AND 7901 ERROR. THE EMERGENCY STOP BUTTON

IS OUT

(FIGURE 30.)

6. 2FO1 ERROR. YOU PRESSED THE FOOT PEDAL BEFORE

TURNING ON THE KEY. TURN OFF THE KEY AND TRY AGAIN,
LEAVING FOOT OFF OF THE PEDAL.

(FIGURE 32.)

7. 2C00 AND 2C01 ERROR. LOW VOLTAGE WARNING.

VOLTAGE HAS DROPPED DOWN BELOW THE MINIMUM
REQUIRED TO OPERATE THE MACHINE. IF YOU WAIT A FEW
MINUTES, THE BATTERIES MAY COAST UP A BIT IN VOLTAGE,
ALLOWING YOU TO DRIVE VERY SLOWLY TO THE
RECHARGE STATION. IF NOT, YOU WILL HAVE TO RELEASE
THE PARKING BRAKE ( ON THE FRONT WHEEL, PULL LEVER
TOWARD THE FRONT OF THE MACHINE TO RELEASE) AND
PUSH THE MACHINE TO RECHARGING STATION.
(FIGURE 32.)

8. 7802 ERROR. THE TRACTION MOTOR WAS USED TO

CLIMB A RAMP, AND WAS RUNNING UP THE RAMP FOR
MORE THAN THE 60 SECONDS ALLOWED FOR THIS. TURN
OFF THE KEY, TURN ON AGAIN, AND CONTINUE. YOU
SHOULD NOT USE THIS MACHINE TO CLIMB RAMPS SO
STEEP AND SO LONG THAT THIS CODE COMES UP
REPEATEDLY, OR YOU COULD OVERHEAT THE TRACTION
MOTOR.

(FIGURE 30.)

9. ALL OTHER ERROR CODES. TURN OFF THE KEY, AND DISCONNECT THE POSITVE BATTERY CABLE FROM THE BATTERIES
FOR MORE THAN ONE MINUTE (THE TIME IS NEEDED TO DRAIN THE BRAIN'S ON-BOARD CAPACITOR). RECONNECT
CABLES, BEING SURE THAT IT IS TIGHT. TOO LOOSE AND YOU WILL BURN BATTERY. IF YOU OVERTIGHTEN THE CABLES YOU
CAN DAMAGE THE BATTERY'S LEAD TERMINAL. TRY AGAIN.

10. IF THE PROBLEMS CANNOT BE SOLVED BY ANY OF THESE SOLUTION CALL YOUR LOCAL DEALER'S SERVICE
DEPARTMENT.

chadv PAGE 19 11/23/2005 9:54:13 AM

 TROUBLE SHOOTING

PROBLEM CAUSE SOLUTION

NO POWER, NOTHING OPERATES FAULTY KEY SWITCH CONTACT LOCAL SERVICING DEALER
BATTERIES NEED CHARGING SEE CHARGING BATTERIES
FAULTY BATTERY REPLACE BATTERY
LOOSE BATTERY CABLE TIGHTEN LOOSE CABLE
MAIN CIRCUIT BREAKER TRIPPED WAIT 5 MINUTES FOR AUTO RESET
DETERMINE CAUSE AND CORRECT

BRUSH MOTOR(S) DO NOT OPERATE BRUSH DECK IS NOT DOWN PUT BRUSH DECK DOWN
FOOT PEDAL IS NOT DEPRESSED ENGAGE FOOT PEDAL
BRUSH CIRCUIT BREAKER TRIPPED WAIT 5 MINUTS FOR AUTO RESET
DETERMINE CAUSE AND CORRECT
CARBON BRUSHES WORN CONTACT LOCAL SERVICING DEALER
FAULTY BRUSH MOTOR OR WIRES CONTACT LOCAL SERVICING DEALER

DRIVE MOTOR DOES NOT OPERATE RECHARGE SWITCH MISADJUSTED CONTACT LOCAL SERVICING DEALER
FAULTY SPEED CONTROLLER OR WIRES CONTACT LOCAL SERVICING DEALER
FAULTY DRIVE MOTOR CONTACT LOCAL SERVICING DEALER
FAULTY WIRING CONTACT LOCAL SERVICING DEALER
CARBON BRUSHES WORN CONTACT LOCAL SERVICING DEALER

VACUUM MOTOR DOES NOT OPERATE SQUEEGEE IS IN THE UP POSITION ROTATE SQUEEGEE LIFT LEVER DOWN
FAULTY VACUUM SWITCH TRY OPERATING "WHITE " TOGGLE
VACUUM CIRCUIT BREAKER TRIPPED WAIT 5 MINUTES FOR AUTO RESET
DETERMINE CAUSE AND CORRECT
FAULTY VACUUM MOTOR CONTACT LOCAL SERVICING DEALER
CARBON BRUSHES WORN CONTACT LOCAL SERVICING DEALER

DRIVE MOTOR RUNS INCORRECTLY FAULTY SPEED CONTROLLER OR WIRES CONTACT LOCAL SERVICING DEALER
FAULTY POTENTIOMETER CONTACT LOCAL SERVICING DEALER
LOOSE WIRES CONTACT LOCAL SERVICING DEALER

INSUFFICIENT SOLUTION FLOW SOLUTION TANK LOW REFILL SOLUTION TANK, DRAIN
RECOVERY TANK
FLOW KNOB TURNED DOWN MOVE LEVER TO ON
SOLUTION FILTER CLOGGED REMOVE COVER AND CLEAN
SOLUTION LINE CLOGGED REMOVE AND BLOW OUT WITH
COMPRESSED AIR
SOLUTION VALVE CLOGGED REMOVE COVER AND CLEAN

chadv PAGE 20 11/23/2005 9:54:13 AM

 TROUBLE SHOOTING

PROBLEM CAUSE SOLUTION

NO SOLUTION FLOW NO SOLUTION IN TANK FILL SOLUTION TANK

SOLUTION VALVE OFF ROTATE LEVER TO ON
SOLUTION SWITCH OFF TURN SOLUTION SWITCH ON
SOLUTION SCREEN CLOGGED REMOVE AND CLEAN SCREEN
FAULTY SOLUTION SOLENOID CONTACT LOCAL SERVICING DEALER
FAULTY SOLUTION SWITCH CONTACT LOCAL SERVICING DEALER

POOR WATER RECOVERY RECOVERY TANK IS FULL EMPTY RECOVERY TANK

BALL/SCREEN IN RECOVERY REMOVE SCREEN AND CLEAN
TANK IS CLOGGED
VACUUM HOSE IS CLOGGED REMOVE DEBRIS
SQUEEGEE IS CLOGGED REMOVE DEBRIS
SQUEEGEE BLADE IS WORN ROTATE OR REPLACE BLADES
FAULTY VACUUM HOSE CONTACT LOCAL SERVICING DEALER
VACUUM MOTOR GASKET TORN CONTACT LOCAL SERVICING DEALER
TANK GASKET FAULTY CONTACT LOCAL SERVICING DEALER
DRAIN PLUG LOOSE TIGHTEN LID
VAC MOTOR FAULTY CONTACT LOCAL SERVICING DEALER
BATTERY CHARGE LOW CHARGE BATTERIES OVERNIGHT

POOR WATER RECOVERY ON TURNS WIPERS WORN REPLACE WIPER MATERIAL

WIPERS CHATTER TIGHTEN PIVOT POINTS
SQUEEGEE SWING IS BINDING CONTACT LOCAL SERVICING DEALER
INCORRECT SQUEEGEE SIZE CONTACT LOCAL SERVICING DEALER

REAR TIRES NOISY BEARING DRY GREASE BEARINGS

FAULTY HUBS CONTACT LOCAL SERVICING DEALER

POOR TRACTION EXCESSIVE BRUSH PRESSURE REDUCE PRESSURE WITH SWITCH

WORN DRIVE TIRE
HEAVY SOAP CONCENTRATION CONTACT LOCAL SERVICING DEALER

SHORT RUN TIME BATTERIES RUN DOWN CHARGE BATTERIES TWICE

BATTERIES STILL DOWN CONTACT LOCAL SERVICING DEALER
BATTERIES LOW ON WATER FILL WITH DISTILLED WATER TO 3/4"
ABOVE THE LEAD PLATES
BATTERIES OVER CYCLED CONTACT LOCAL SERVICING DEALER

chadv PAGE 21 11/23/2005 9:54:13 AM

 MODEL 290/350

MACHINE PARTS SECTION

SOME PARTS ARE MADE IN RED AND YELLOW. IF YOU NEED YELLOW PARTS
USE THE ALTERNATE PART NUMBER WHICH WILL START WITH (291-XXXX). IF
YOU NEED RED PARTS, USE THE NORMAL PART NUMBER THAT WILL START WITH
(290-XXXX). IF THERE IS ONLY ONE PART NUMBER, THAT IS THE ONLY COLOR
THAT PART COMES IN.

chadv PAGE 22 11/23/2005 9:54:13 AM

 SOLUTION SYSTEM
51

30 43
29 8
4 42
44 17
10
9 43 38 42
5
31
6
3
13 41

2
1

33
50
34

47 33 22
40 23
11 24
To
Scrubhead
20 48
49 7
14 45 16 18 19 21 27 28 46
34
26 26
36 35 15 35 36

12 40 39 37 25

PAGE 23
 SOLUTION SYSTEM
Item Part No. Alt. Part No. Part Desription Qty
1 290-4140 291-4140 SOLUTION TANK 1
2 290-1480 BATTERY TRAY 1
3 290-2110 BATTERY 6 VOLT 395 AH 4
4 290-1300 BATTERY COMP'T COVER 1
5 290-4152 SOLUTION TANK LID 1
6 290-4153 SOL TANK LID GASKET 1
7 H-01519 1/4-20 X 1.75 " U BOLT 2
8 290-4151 LID STRAP 1
9 5-122 HINGE 8" SS 2
10 21-7101 LIFT KNOB 1
11 21-4500 ADJUSTABLE SOLUTION FLOW VALVE 1
12 H-3225T5 RUBBER LOOP CLAMP 1
13 5-728 DETERGENT WARNING PLATE 1
14 5-913 INLINE FILTER 1
15 290-4158 1/2" NPT BALL VALVE 1
16 290-4175 1/2" ID X 3/4" OD X 28.0" LG CLEAR TUBE 1
17 290-8520 FLOAT VALVE ASSEMBLY 1
18 290-4155 1/2" NPT X 1/2" BARBED TEE 1
19 H-081 CLAMP 7/16"- 25/32" SS 7
20 290-4160 1/2" ID X 3/4" OD X 5.0" LG CLEAR TUBE 1
21 290-4164 1/2" ID X 3/4" OD X 24.0" LG CLEAR TUBE 1
22 H-99001 FW 3/8" SS 6
23 H-71065 LW 5/16" SS 6
24 H-70053 HCS 5/16"- 18 X 3/4" SS 6
25 290-4159 1/2" ID X 3/4" OD X 15.0" LG CLEAR TUBE 1
26 H-NJ04C JNYL 1/4" - 20 SS 2
27 5-447 1/2" NPT TO 1/2" BARBED ELBOW 1
28 290-4550 1/2" NPT BALL VALVE 1
29 H-33618 LW 1/4" 4
30 H-37708 1/4-20 LC ACORN NUT 4
31 H-13001 HCS 1/4"- 20 X 1/2" 3
32 290-4150 1/4" ID X 1/2" OD X 14" LG CLEAR TUBE 1
33 290-4149 1/4" NPT X 1/4" BARB X 90 DEG 2
34 H-70003 HCS 1/4"- 20 X 3/4" SS 2
35 21-4042 1/2" NPT X 90 DEG ST ELBOW 2
36 290-4176 .50 NPT X .50 BARB 2
37 H-70858 NYLOK #10-32 SS 2
38 H-33620 LW 5/16" 1
39 H-71063 LW 1/4" SS 1
40 H-70710 HN 1/4"- 20 SS 3
41 H-13053 HCS 5/16"-18 X 3/4" 1
42 H-33080 FW 5/16" SAE 2
43 H-13051 HCS 5/16"- 18 X 1/2" 2
44 H-37021 NYLOK 5/16"-18 1
45 H-72563 RPH #10-32 X 1/2" SS 2
46 H-07005 1/2" NPT LOCKNUT 1
47 290-4174 1/2" ID X 3/4" OD X 19.0" LG CLEAR TUBE 1
48 290-7721 LEVER GRIP 1
49 290-7720 BALL VALVE LEVER 1
50 290-4148 7/32" POLYPROPYLENE BALL 1
51 8-143 SEAT WITH ARM RESTS 1
PAGE 24
 RECOVERY SYSTEM
38 20
28 26
22 4
38
26 18
17 26
3
29 5
18 18
14 21
26
18 24
24 37
37 36 16 39
36 35 20
7 26
35 13 SEE ITEM 9
26 33 (FRAME BOTTOM)
10 13 12
19

30
6 31 32
25
15 2
34
8
27
9

11

20
9

23

PAGE 25
 RECOVERY SYSTEM
Item Part No. Alt. Part No. Part Desription Qty
1 290-7010 291-7010 RECOVERY TANK 1
2 5-920 DRAIN HOSE END TUBE 1
3 290-4112 RECOVERY TANK LID 1
4 290-4110 VAC SCREEN INLET 1
5 290-7390 VAC INLET GASKET 1
6 5-7180 DRAIN HOSE BRACKET 1
7 290-7420 REC TANK LID GASKET 1
8 290-1120 FRONT TANK SUPPORT 1
9 5-719 CLAMP 1 9/16 - 2 1/2 " SS 2
10 21-2211 SPACER 1/2 OD X 1/4" 1
11 7-415 CLEANOUT DOOR W/GASKET & DISC 1
12 290-7040 RECOVERY TANK ELBOW 1
13 38-738 STRAINER GASKET 2
14 8-180 6-7/8" SS HINGE 1
15 H-13053 HCS 5/16"-18 X 3/4" 2
16 8-911 SCREEN STRAINER 1
17 290-4115 VAC INLET HINGE 1
18 H-13001 HCS 1/4"- 20 X 1/2" 9
19 290-7212 1-1/2" - 2" HOSE CUFF 1
20 21-4072 HOSE CUFF, 1 1/2" 3
21 290-7213 VAC HOSE 37" LG 1
22 8-293 STROBE LIGHT 1
23 290-7210 DRAIN HOSE 1
24 H-23213 SHCS 1/4"- 20 X 2 1/2" 2
25 5-727 DRAIN HOSE PLUG 1
26 H-33618 LW 1/4" 11
27 290-7214 VAC HOSE 40" LG 1
28 H-73743 BHSCS 10-32 X 1/2" SS 3
29 H-70858 NYLOK #10-32 SS 3
30 H-33761 5/16" INT/EXT STAR WASHER 1
31 H-71063 LW 1/4" SS 2
32 H-70001 HCS 1/4"-20 X 1/2 SS" 2
33 5-822 Spacer, 1/4" ID, 3/8" OD, 11/16" Long 1
34 H-33620 LW 5/16" 2
35 H-36102 HN 1/4"-20 2
36 5-417 DOOR CLIP 2
37 5-418A CLAMPING KNOB 2
38 H-37708 1/4-20 LC ACORN NUT 5
39 38-712 OVERFILL SHUTOFF BALL 1

PAGE 26
 FRAME TOP
43
4
23
27
5 22
26
CENRTAL COMMAND II 44 48 21
19 31 25 19
26
28
21 17
22

13 28 41
26
42 7
27
10
8

CENRTAL COMMAND 9
25 15 29
12
40
16
18
49
39 38
47 30 11

45 32
46 23
3
2
20 22
6
35 24

15

34
33

43

50
14

37
1

36
22 34

44

PAGE 27
 FRAME TOP
Item Part No. Alt. Part No. Part Desription Qty
1 290-1100 FRAME WELDMENT 1
2 290-1610 NON SKID FLOOR PLATE 1
3 290-1170 291-1170 LOWER STEERING TOWER 1
4 290-1171 291-1171 UPPER STEERING TOWER 1
5 290-1172 291-1172 COVER 1
6 290-1173 DRIVE COVER 1
7 290-1180 291-1180 FRONT APRON 1
8 290-7050 INDEX PLUNGER 1
9 4-101 SERIAL NUMBER PLATE 1
10 8-291 HEADLIGHT 1
11 4-257 CONNECTOR, RED 50, WITH CONTACTS 1
12 8-290 FOOT PEDAL 1
13 8-294B PUSH BUTTON SWITCH, SILVER 1
14 7-125A ROLLER 2
15 8-292 BACKUP ALARM 1
16 21-2230 MICRO SWITCH 1
17 8-294 HORN 1
18 H-28902 RPH #8-32 X 1" 2
19 H-76061 FW 1/4" NYLON 12
20 H-37015 NYLOK #10-32 2
21 H-73754 BHSCS 1/4 - 20 X 3/4" SS 12
22 H-33620 LW 5/16" 16
23 H-13053 HCS 5/16"-18 X 3/4" 8
24 H-33074 FW #10 SAE 6
25 H-71063 LW 1/4" SS 2
26 H-76063 FW 3/8" NYLON 6
27 H-250HCN HCN 1/4"-20 8
28 4
29 H-29048 RPH #10-32 X 1/2" 2
30 H-71009 FW #10 SS 2
31 H-13055 HCS 5/16"-18 X 1" 4
32 H-72565 RPH #10-32 X 3/4" SS 2
33 H-11380 HCS 3/4-10 X 8-1/2 2
34 H-312HCN HCN 5/16"-18 25
35 H-29072 RPH #10-32 X 1" 4
36 H-37039 NYLOK 3/4"- 10 2
37 H-1032HCN HCN #10-32 4
38 H-33066 FW #4 SAE 2
39 H-28678 RPH #4-40 X 1" 2
40 H-37006 NYLOK #4-40 2
41 H-37024 NYLOK 3/8"-16 2
42 H-73815 BHSCS 3/8"- 16 X 1" SS 2
43 H-21253 CB 5/16"- 18 X 3/4" 5
44 H-36104 HN 5/16"-18 5
45 H-71009 FW 3/16" X 7/16" SS 2
46 H-73747 RPH #10-32 X 1 1/4" SS 2
47 H-70858 NYLOK #10-32 SS 2
48 H-70003 HCS 1/4"- 20 X 3/4" SS 2
49 H-37406 KN #8-32 2
50 290-1115 BOTTOM LATERAL TANK LOCATOR 2

PAGE 28
 FRAME BOTTOM
4

1 NOTE:
SPLASH CURTAINS ARE
2 USED ON DISk MACHINES ONLY.
35
3 34
30
26
22 23
25 6

26 8
21
24
35 14 7
25
10 42 34
30 30
31
23 11
43
44 20
22
NA
14 28 35
41
5 30
21
23
45 20
32
16 14 33
40 12 CYL POS.
25 25
26 19
32 15 12 DISC POS.
37 20
31

30
38
20 13 27
15 39
18

36 29
9 18
17 21 47
46 17
17

PAGE 29
 FRAME BOTTOM
Item Part No. Alt. Part No. Part Desription Qty
1 290-6040 REAR AXLE 1
2 290-6180 290-6185 REAR WHEEL (GREY STD.) (BLACK OPT.) 2
3 290-6187 LUG NUT, 1/2"- 20 1
4 290-6186 1/2-13 X 1-1/4 " U BOLT 4
5 290-5000 AXLE MOUNT 1
6 290-5001 SQUEEGEE DRAG BRACE 1
7 290-1253 REAR SPLASH CURTAIN 1
8 290-1254 REAR CURTAIN MTG STRIP 1
9 290-3003 VAC INLET ASS'Y 1
10 290-1250 REAR SPLASH GUARD 1
11 290-1260 FRONT SPLASH GUARD 1
12 290-1265 SCRUB ARM BRACKET 4
13 5-225 VAC MOTOR 1
14 H-70103 HCS 3/8"-16 X 3/4" SS 20
15 H-NJ04C JNYL 1/4" - 20 SS 9
16 H-37130 NYLOK NUT, 1/2"- 20 8
17 H-29598 FPH 5/16"- 18 X 1" 17
18 H-13053 HCS 5/16"-18 X 3/4" 4
19 H-71017 FW 3/8" SS 3
20 H-70710 HN 1/4"- 20 SS 20
21 H-71013 FW 1/4" X 5/8" SS 12
22 H-70858 NYLOK #10-32 SS 8
23 H-71016 FW 5/16" X 7/8" USS 12
24 H-70105 HCS 3/8"- 16 X 1" SS 2
25 H-71067 LW 3/8" SS 10
26 H-70712 HN 3/8"-16 SS 6
27 H-33080 FW 5/16" SAE 8
28 H-0129158 JNYL 3/8- 16 SS 16
29 H-70145 HCS 3/8"- 24 X 1 3/4" SS 4
30 H-33620 LW 5/16" 21
31 H-70861 NYLOK 5/16" - 18 SS 9
32 H-71063 LW 1/4" SS 14
33 H-70732 HN 3/8"- 24 SS 4
34 H-72684 FHP 10-32 X 3/4" SS 12
35 H-NJ05C JNYL 5/16"- 18 SS 12
36 290-3001 VAC BOX GASKET 1
37 5-708A VAC MOTOR GASKET 1
38 38-734 BLOWER RING 1
39 H-00221 FTS 1/4"- 20 X 5" SS 1
40 5-891 PUMP, WATER JET 1
41 290-8500 PUMP 24V DC (OPTIONAL) 1
42 290-1310 FR. SPLASH CURTAIN - SHORT 1
290-1315 FR. SPLASH CURTAIN - LONG
43 290-1320 CURTAIN MTG STRIP - SHORT 1
290-1325 CURTAIN MTG STRIP - LONG
44 H-70003 HCS 1/4"- 20 X 3/4" SS 8
45 H-70860 NYLOK 1/4"- 20 SS 4
46 H-72686 FHP 10-32 X 1-1/4" SS 4
47 H-70005 HCS 1/4"- 20 X 1" SS 4
48 H-71009 FW #10 SS 6

PAGE 30
 DOOR/WIPER/ROLLER ASSEMBLY
3

2
4

PN 5-123B MODEL 350 DISC POSITION BOTH SIDES 17

USE PN 290-1235 FOR 290 & 350 CYL'S LEFT SIDE

26
22
7 26 1
35 33
22
22
21
33 28
37 20 34
25 6 35
20 13 20 21
32
22
30 31 23
13
19 33 5
12 12 30 35
19
9
12

29
16
14 10
33
24 26
PN 5-123B MODEL 290 DISC POSITION BOTH SIDES 17 26 27
USE PN 290-1235 FOR 290 CYL'S RIGHT SIDE 22
USE PN 290-1236 FOR 350 CYL'S RIGHT SIDE 35 38
24 26
18
26 8

38
24
36 15

11

PAGE 31
DOOR/WIPER/ROLLER ASSEMBLY
Item Part No. Part Desription Qty
1 290-1270 FRONT LH POD 1
2 290-1280 REAR LH POD 1
3 290-1290 LH POD TOP SUPPORT 1
4 290-1230 LEFT WIPER 1
5 290-1271 FRONT RH POD 1
6 290-1281 REAR RH POD 1
7 290-1291 RH POD TOP SUPPORT 1
8 290-1231 RIGHT WIPER 1
9 290-1220 DOOR 2
10 290-1126 ROLLER BRACKET 2
11 290-4030 WIPER BAND 2
12 290-1248 FW BRONZE .500 ID X 1.00 OD X .125 THK 8
13 290-1243 3/8" ID, 1/2" OD, 1/4" LG BEARING 8
14 5-130 DOOR LATCH 2
15 5-402LA WIPER BLADE 2
16 5-122 8" SS HINGE 2
17 5-123B WIPER LIFTING BRACKET 2
290-1235
18 21-1127 ROLLER 8
19 21-1050 PARALLEL LINK 4
20 H-70055 HCS 5/16"- 18 X 1" SS 16
21 H-250HCN HCN 1/4"-20 8
22 H-71013 FW 1/4" X 5/8" SS 36
23 H-71021 FW 3/8" X 7/8" SS 6
24 H-70861 NYLOK 5/16" - 18 SS 8
25 H-71065 LW 5/16" SS 8
26 H-70003 HCS 1/4"- 20 X 3/4" SS 36
27 H-37038 JNYL 5/8"- 11 2
28 H-70712 HN 3/8"-16 SS 6
29 H-70103 HCS 3/8"-16 X 3/4" SS 6
30 290-1234 .375 OD. X .31 ID. X .625 LG 4
31 H-70005 HCS 1/4"- 20 X 1" SS 8
32 H-71067 LW 3/8" SS 6
33 H-70710 HN 1/4"- 20 SS 36
34 H-13337 HB 5/8"- 11 X 13" 2
35 H-71063 LW 1/4" SS 36
36 H-72706 FHP 1/4"- 20 X 5/8" SS 18
37 H-78015 FW 5/16" X 3/4" SS 13
38 290-1245 3/8" ID, 1/2" OD, 3/8" LG, FLANGE BEARING 8
PAGE 32
STEERING/TRACTION ASSEMBLY
18 19
37 23
35
36
35
22
21
4
27
3
27
5 38
26
13
12
11
9
17 10
10
17 16
9
20
11
27
7
28
33
34
31
24
32
30 25
6
8 14
15
29
39 2
41
1
42 40

PAGE 33
STEERING/TRACTION ASSEMBLY

Item Part No. Part Desription Qty

1 290-7315 BLACK TIRE (OPTIONAL) 1
290-7320 GREY TIRE (STANDARD)
2 290-7326 PIVOT PLATE 1
3 290-7110 U-JOINT 1
4 290-7090 STEERING SHAFT, UPPER 1
5 290-7120 STEERING SHAFT, LOWER 1
6 37-7314 LARGE STEERING SPROCKET 1
7 37-7315 DROP PLATE 1
8 37-7316 PIVOT SHAFT 1
9 37-7317 TAPERED ROLLER BEARING 2
10 37-7318 BEARING CAP 2
11 37-7319 STEERING SHAFT SEAL 2
12 37-7320 PRE LOAD SLEEVE 1
13 37-7321 SLOTTED NUT, 2.0 - 12 1
14 290-7327 STEERING CHAIN 1
15 5-831 MASTER LINK 1
16 8-723 BEARING BLOCK 1
17 8-723B BEARING 2
18 8-703 STEERING WHEEL 1
19 8-701A STEERING COVER 1
20 5-826 10 TOOTH SPROCKET 1
21 H-36104 HN 5/16"-18 6
22 H-33620 LW 5/16" 5
23 H-37038 JNYL 5/8"- 11 1
24 H-13003 HCS 1/4"-20 X 3/4" 2
25 H-24103 BHSCS 3/8"- 24 X 1" 6
26 H-65129 3/16" X 2-1/2" COTTER PIN 1
27 H-00270 3/16" X 3/4" KEY 3
28 H-68013 SNAPRING 5/8" 1
29 H-28121 FHS 3/8-16 X 1" 4
30 H-33618 LW 1/4" 2
31 H-13055 HCS 5/16"-18 X 1" 2
32 H-25595 SS CP 3/8"- 24 X 1/2" 1
33 H-05233 PVC TUBING 1
34 H-24617 SHCS, LOW HEAD, 1/4- 20 X 5/8" 2
35 4-364A FLANGE, 1.75" ID 2
36 4-352 BEARING 1
37 H-94071 BHSCS 5/16-18 X 1 3
38 H-25328 SSS CP 1/4"-20 X 3/8" 2
39 290-7313 24V, 2HP, MOTOR 1
40 H-79041 SHCS 1/4-20 X 1/2 SS 3
41 290-7323 24 VOLT ELECTRIC BRAKE 1
42 5-2225 END HOUSING 1

PAGE 34
 ACTUATOR SLIDE ASSEMBLY

9
9 9 24 9 3
13
24
9 25
20 3

8 16 21
26
2 18 9
7
1

1 19 12
5 4 3

14
22 6

23 2

5 5 11 17 6

14 15

PAGE 35
ACTUATOR SLIDE ASSEMBLY

Item Part No. Part Desription Qty

1 H-37408 KN #10-32 4
2 290-7660 ACTUATOR CHANNEL 1
3 H-33374 SHAFT COLLAR, 1/2" ID 16
4 5-772 PULLEY, NYLON 3
5 H-11219 HCS 1/2"- 13 X 4.0" 8
6 290-7710 CABLE TROLLEY 2
7 5-223 LIMIT SWITCH 4
8 290-2210 ACTUATOR; 1000 LB. LOAD (20:1) 1
9 H-36152 HN 1/4"- 28 18
10 H-6389 FLANGED BUSHING 3/8" ID X 5/8" OD, NYLON 3
11 H-28679 PPH #4-40 X 1" 8
12 H-37006 NYLOK #4-40 6
13 5-221 ACTUATOR; 1000 LB. LOAD (10:1) 1
14 21-7690 POLYURETHANE SPRING 2
15 H-33207 FW 1/4" X 1" 1
16 H-37032 JAM NYLOK NUT, 1/2"- 13 8
17 H-33066 FW #4 SAE 8
18 H-72566 RPH #10-32 X 1" SS 2
19 H-78LC 7/8" NYLON LOOP CLAMP 2
20 290-7713 SCRUBHEAD LIFT CABLE 12.25" 2
21 290-7890 SQUEEGEE LIFT CABLE 1
22 H-01321 DOUBLE ENDED STUD, 1/4-20 X 4" SS 2
23 H-NJ04C JNYL 1/4" - 20 SS 4
24 290-7712 COMPRESSION SPRING 6
25 290-4010 LIFT BRACKET 1
26 5-270 EMF SUPP DIODE 4
27 H-01320 FW 1/2" ID X 1/8" THICK NYLON 2

PAGE 36
 DISK SCRUBHEAD ASSEMBLY

19 9

13
2
6
8 11 8
4
4
26 12
16 10
15
26 20
27 26
16 14
26 27
5 5
3 17
15

5
17
SEE 290-1265 18
FRAME BOTTOM 1
17

7
21 10
NOTE:
40-423-DISK BRUSH REPAIR KIT &
40-433-RETAINER RING ARE NOT
SHOWN.

BRUSH
(SEE COMMON WEAR PARTS) 22
23
24
25

PAGE 37
DISK SCRUBHEAD ASSEMBLY
Item Part No. Part Desription Qty
1 7-402 SCRUB HEAD PLATFORM 1
2 38-222 MOTOR 1 HP X 350 RPM 2
3 5-124 LATERAL ARM 4
4 H-70110 HCS 3/8"- 16 X 1-3/4" SS 8
5 H-70712 HN 3/8"-16 SS 11
6 7-4034 REINF. HOSE 5/8 ID X 18" LG 1
7 H-70105 HCS 3/8"- 16 X 1" SS 7
8 5-447 1/2 NPT X 1/2" BARB ELBOW 2
9 5-446 1/2 " PLASTIC BARB TEE 1
10 H-07005 1/2" NPT LOCKNUT 4
11 290-4010 LIFT BRACKET 1
12 H-CP238 1/2" X 3" CLEVIS PIN 1
13 H-78LC 7/8 LOOP CLAMP 2
14 H-76063 FW 3/8" NYLON 2
15 290-1247 FW BRONZE .50" ID X 1.0" OD X .062 5
16 290-1245 3/8" ID, 1/2" OD, 3/8" LG, FLANGE BEARING 3
17 H-71067 LW 3/8" SS 11
18 H-72565 RPH #10-32 X 3/4" SS 1
19 H-70858 NYLOK #10-32 SS 1
20 H-RUE22 1/2" RUE RING COTTER 1
21 21-5000 BRUSH DRIVER 2
22 H-99001 FW 3/8" SS 2
23 H-71016 FW 5/16" X 7/8" USS 2
24 H-71065 LW 5/16" SS 2
25 H-70055 HCS 5/16"- 18 X 1" SS 2
26 H-71017 FW 3/8" SS 10
27 290-1243 3/8" ID, 1/2" OD, 1/4" LG BEARING 2

PAGE 38
 CYLINDRICAL-DECK
46

53
54 8 17 17 3

31 26 26 31 55 61 50 13
31 18 32 27 38 37
19
29 32 45 6

19 40 21 25
55 4 32 51 16 8 11
56 49
9
7 14 49
52
35 58 35 49
15 39 33 43 62 60
22 28 48 47 1 5
28 44
23 24
11
1 59
10 23 24
38
36 20 2
34 41
30
SEE ITEM 12 25
(FRAME BOTTOM)
30 42
57

12

IDLER DOOR
ASSEMBLY
5-8010

PAGE 39
 CYLINDRICAL-DECK

Item Part No. Part Description Qty Item Part No. Part Description Qty
1 32-9000 32" CYL BRUSH HEAD 1 29 H-71016 FW 5/16" X 7/8" USS 2
2 25-9050 25" HOPPER 1 30 H-33008 FW 3/8" USS 4
28-9050 28" HOPPER 31 H-71063 LW 1/4" SS 8
7-811 32" HOPPER 32 H-71065 LW 5/16" SS 7
3 25-8320 HOPPER RAIL, 25" 1 33 H-33614 LW #10 2
28-8320 HOPPER RAIL, 28" 34 H-33622 LW 3/8" 2
5-832 HOPPER RAIL, 32" 35 1-421 IDLER BEARING 4
4 290-8355 DRIVE SHAFT, 25" CYL 1 36 H-70105 HCS 3/8-16 X 1" SS 3
290-8360 DRIVE SHAFT, 28" CYL 37 H-73815 BH SCHS 3/8-16 X 1" SS 1
290-8365 DRIVE SHAFT, 32" CLY 38 H-71067 LOCKWASHER 3/8 SS 4
5 SEE PAGE 4 CYLINDRICAL BRUSH 2 39 H-25452 SB 1/2" X 1/2" SS 2
6 5-801 IDLER DOOR 1 40 28-9005 FAN PLATE MOUNT 1
7 H-72710 FHP 1/4"- 20 X 1" SS 3 41 28-9060 HOPPER SPLASH SHIELD 1
8 H-70005 HCS 1/4"- 20 X 1" SS 5 42 28-9070 SPLASH SHIELD HOPPER 1
9 H-70055 HCS 5/16"- 18 X 1" SS 2 STRIP
10 H-70105 HCS 3/8"- 16 X 1" SS 2 43 H-35313 17mm SNAP RING 2
11 H-01219 HCS 3/8"- 24 X 1 1/8" SS 2 44 290-1350 CYL SUPPORT BRACKET 1
12 H-72563 RPH #10-32 X 1/2" SS 8 45 290-8100 FAN MTG BRACKET 1
13 H-72565 RPH #10-32 X 3/4" SS 2 46 22-2110 2 HP MOTOR 1
14 290-1245 3/8" ID, 1/2" OD, 3/8" LG, 2 47 7-843 ADJ LATERAL ARM 1
FLANGE BEARING 48 290-9020 CYLINDRICAL LIFT ARM 1
15 290-1246 1/2" ID X 5/8" OD X 1/2" LG 2 49 H-17002 FW 17mm NYLON 6
FLANGED BEARING 50 5-212 COOLING FAN 1
16 H-3225T5 RUBBER LOOP CLAMP 1 51 5-446 1/2 " PLASTIC BARB TEE 1
17 H-01125 3/16" X 1" KEY 2 52 H-70055 HB 5/16"- 18 X 1" SS 2
18 H-70710 HN 1/4"- 20 SS 2 53 H-72684 FHP 10-32 X 3/4" SS 9
19 H-70711 HN 5/16"- 18 SS 4 54 5-8102 BEARING PLATE 1
20 H-36106 HN 3/8"-16 2 55 5-829 FLANGE BEARING 2
21 H-NJ04C JNYL 1/4" - 20 SS 1 56 H-25444 SB 3/8" X 3/8" SS 2
22 H-NJ05C JNYL 5/16"- 18 SS 2 57 5-834 HOPPER HANDLE 1
23 H-0129158 JNYL 3/8- 16 SS 4 58 5-838 BRUSH IDLER 2
24 H-00531 JNYL 3/8- 24 SS 2 59 5-849 RECESSED HANDLE 1
25 H-70858 NYLOK #10-32 SS 10 60 5-858 IDLER SHAFT 2
26 H-70860 NYLOK 1/4"- 20 SS 6 61 8-613 FLEXIBLE COUPLER 1
27 H-70911 WINGNUT 5/16"- 18 SS 3 62 H-00797 FW 17.3mm X 33.2mm X 2
28 290-1248 FW BRONZE .500 ID X 1.00 4 1.6mm
OD X .125 THK

PAGE 40
CYLINDRICAL-MECHANICAL

33 2 23 23
5 20 25 23
11
6
36
18
32
35 32 27
30 36
31 35 10
22 12 21
14 7
24 23
28 1
19
16
30
30
34
8
13
34
26 15
3
17
4 29 36

PAGE 41
CYLINDRICAL-MECHANICAL
Item Part # Description Qty
1 1-305 BEARING HOUSING 2
2 22-7970 MOVABLE IDLER ARM 1
3 22-8300 DRIVE CHAIN 1
4 22-9021 CHAIN GUARD 1
5 290-8260 10 TOOTH SPROCKET 1
6 4-317 IDLER PULLEY 1
7 4-319 TENSION SPRING 1
8 5-793 IDLER SPACER 1
9 5-796 GREASE (USE ONLY OEM GREASE - NOT SHOWN) 1
10 5-798 SPRING PIVOT 1
11 5-822 Spacer, 1/4" ID, 3/8" OD, 11/16" Long 1
12 5-824 DRIVE BEARING 2
13 5-827 20 TOOTH SPROCKET 1
14 5-828 22 TOOTH SPROCKET 2
15 5-831 MASTER LINK 1
16 5-837 BROOM DRIVER 2
17 5-845A WINDLACING - (WEATHER STRIPPING) 1
18 H-00272 SCS 1/4"- 20 X 1.0" 1
19 H-00279 WASHER 5/8 TEFLON 1
20 H-01343 1/8" X 1/8" X 3/4" KEY 1
21 H-15009 HCS 1/4"- 20 X 1-1/2" GRADE 8 1
22 H-255HD STUD 1/4"- 20 X 1" 2
23 H-33208 F W 1/4" X 1 1/4" 4
24 H-36202 JN 1/4"- 20 2
25 H-68011 SNAPRING .5" 1
26 H-70145 HCS 3/8-24 X 1 3/4" SS 1
27 H-70710 HN 1/4"- 20 SS 1
28 H-70732 HN 3/8"- 24 SS 1
29 H-71013 FW 1/4" X 5/8" SS 2
30 H-71017 FW 3/8" SS 3
31 H-72682 FHP 10-32 X 1/2" SS 1
32 H-76063 FW 3/8" NYLON 2
33 H-93580 SCS 1/4"- 20 X 1 1/4" 1
34 H-98025 WASHER 3/8 GRADE 8 2
35 H-K1432 3/16" X 1/2" KEY 4
36 H-NJ04C JNYL 1/4" - 20 SS 4
PAGE 42
 SQUEEGEE ASSEMBLY
44

34
37 31
SEE ITEM 6
34 (FRAME BOTTOM)
31
42
33 31

38
47
24 35 43
27 35
38 38
26
34 31
21 25
SQUEEGEE BACK UP
WHEEL 19 WHEEL KIT
ASSEMBLY 5-757
5-760 11 7
18 10

12

17
14
18 32
41
24 6 39
20 29
48
40 32
9 36

30

46
13
30 3

28

4
5 2

15 13
16 45
1 8
22 23

PAGE 43
 SQUEEGEE ASSEMBLY
Item Part No. Part Desription Qty Item Part No. Part Desription Qty
1 22-7181 30" SQUEEGEE WELDMENT 1 20 H-70711 HN 5/16"- 18 SS 2
25-7181 35" SQUEEGEE WELDMENT 21 5-786 WINGNUT 3/8"-16 NICKEL 2
28-7181 38" SQUEEGEE WELDMENT
290-7181 45" SQUEEGEE WELDMENT 22 H-70908 WINGNUT 10-32 SS 8
2 22-755G 30" SQUEEGEE BLADE, FRONT 1 23 H-00249 PPH #10-32 X 2 1/4" SS 4
25-755G 35" SQUEEGEE BLADE, FRONT 24 H-33371 5/16" ID SHAFT COLLAR 3
28-755G 38" SQUEEGEE BLADE, FRONT
290-756G 45" SQUEEGEE BLADE, FRONT 25 21-7610 SQUEEGEE TRIANGLE PLATE 1
3 22-7170 30" SQUEEGEE BAND, FRONT 1 26 H-33080 FW 5/16" SAE 1
25-7170 35" SQUEEGEE BAND, FRONT 27 21-7205 PALM GRIP KNOB, 3/8-24 1
28-7170 38" SQUEEGEE BAND, FRONT 28 H-10055 HCS 3/8"- 24 X 3.5" SS 1
290-7170 45" SQUEEGEE BAND, FRONT
29 290-7150 SQUEEGEE TRAIL ARM 1
4 22-754G 30" SQUEEGEE BLADE, REAR 1
25-754G 35" SQUEEGEE BAND, REAR 30 H-70136 HCS 3/8"- 24 X 2 1/4" SS 2
28-754G 38" SQUEEGEE BLADE, REAR 31 H-76063 FW 3/8" NYLON 7
7-753G 45" SQUEEGEE BLADE, REAR
32 290-1248 FW BRONZE .500 ID X 1.00 OD X .125 THK 1
5 22-7160 30" SQUEEGEE BAND, REAR 1 33 290-7130 SQUEEGEE SWING PLATE 1
25-7160 35" SQUEEGEE BAND, REAR
28-7160 38" SQUEEGEE BAND, REAR 34 H-71017 FW 3/8" SS 4
290-7160 45" SQUEEGEE BAND, REAR 35 H-00531 JNYL 3/8- 24 SS 2
6 21-7220 SQUEEGEE TRAIL MOUNTS 2 36 H-0129158 JNYL 3/8- 16 SS 1
7 21-7570 BACK UP WHEEL (GREY) 2 37 H-77862 NYLOK 3/8"- 16 SS 1
8 H-72555 PPH #10-32 X 1 3/4" SS 2 38 H-NJ05C JNYL 5/16"- 18 SS 4
9 5-846 PIVOT SHAFT 2 39 4-446 GROMMET-3/8 ID X 1-1/2 OD X .375 3
10 HZCP44 CLEVIS PIN 1/4 X 1 1/2" 2 40 21-7240 SPRING 1
11 H-RUE8 1/4" RUE RING COTTER 2 41 7-782C 5/16 CLEAR TUBING 1
12 H-S1060 STUD 3/8-16 X 1 1/2" SS 2 42 290-1245 3/8" ID, 1/2" OD, 3/8" LG, FLANGE BEARING 1
13 H-71067 LW 3/8" SS 3 43 H-2S444 SB 5/16" X 3/8" SS 2
14 H-70005 HCS 1/4"- 20 X 1" SS 4 44 H-79054 SHCS 5/16-18 X 3/4 SS 1
15 H-71063 LW 1/4" SS 4 45 H-70105 HCS 3/8"- 16 X 1" SS 2
16 H-70710 HN 1/4"- 20 SS 4 46 H-00288 PPH #10-32 X 2 1/2" SS 2
17 5-760B SIDE WHEEL (GREY) 2 47 H-90281 1/4-20 X 6" DOUBLE ENDED STUD 1
18 H-71016 FW 5/16" X 7/8" USS 4 48 H-71065 LW 5/16" SS 2
19 H-70065 HCS 5/16"- 18 X 3" SS 2

PAGE 44
 CENTRAL COMMAND II
38 39 25
22 27 12 12 31 33
13
8 14
37
20
9
30
11 41
6
26

19 4 19 12
18

19
19
19 19
21 23
15 7
3 36
24
40

28
10
1

42 34 35
17

32

16

29 31

5 2
PAGE 45
 CENTRAL COMMAND II
Item Part No. Part Description Qty
1 290-2010 CONTROL PANEL 1
2 290-2001 ACCESS COVER 1
3 290-2006 HARDWARE PANEL 1
4 290-2891 LCD SCREEN 1
5 290-2004 ACCESS COVER GASKET 1
6 290-2015 ONE TOUCH BUTTON 1
7 290-2815 CIR. BREAKER - 15A, 24V 2
8 290-2300 LOW SOLUTION (AMBER) 1
9 290-2310 FULL RECOVERY (RED) 1
10 290-2890 COMPUTER CONTROL 1
11 290-2013 CONT PANEL TOP PLATE 1
12 5-234 SWITCH, ROCKER, DPDT, ON/ON 3
13 5-300 EMERGENCY SHUT OFF (OPT) 1
14 5-301 EMERG LEGEND PLATE (OPT) 1
15 5-302 EMERG CONTACT BLK (OPT) 1
16 5-289 CIR BREAKER 24V 50A 4
17 5-293 15 AMP RELAY 1
18 7-283 SWITCH, TOGGLE, MOM/OFF/MOM (DPDT) 1
19 5-892 TOGGLE, ON-OFF SPST 5
20 5-892A PROTECTIVE BOOT, TOGGLE SWITCH, (GRAY) 1
21 7-837 FUSE RESETTABLE 2 AMP 1
22 7-229 PUSH BUTTON SWITCH 1
23 7-821 SWITCH, TOGGLE, ON/ON (DPDT) 1
24 7-287 BUSS BAR UHMW 2
25 4-234 KEY SWITCH 1
26 H-73743 BHSCS 10-32 X 1/2" SS 4
27 H-01200 PROTECTIVE BOOT, TOGGLE SWITCH, (BLACK) 1
28 H-250HCN HCN 1/4"-20 2
29 H-36102 HN 1/4"-20 12
30 H-01196 PROTECTIVE BOOT, TOGGLE SWITCH, (RED) 1
31 H-13005 HCS 1/4"-20 X 1" 4
32 E-4HBB 4 HOLE BUSS BAR 2
33 H-33078 FW 1/4" SAE 4
34 H-71013 FW 1/4" X 5/8" SS 12
35 H-73754 BHSCS 1/4 - 20 X 3/4 SS 12
36 H-33618 LW 1/4" 4
37 H-01199 PROTECTIVE BOOT, TOGGLE SWITCH, (BLUE) 1
38 H-01195 PROTECTIVE BOOT, TOGGLE SWITCH, (WHITE) 1
39 H-01198 PROTECTIVE BOOT, TOGGLE SWITCH, (GREEN) 1
40 E-5HBB 5 HOLE BUSS BAR 2
41 H-01197 PROTECTIVE BOOT, TOGGLE SWITCH, (YELLOW) 1
42 290-2020 BRACKET 1

PAGE 46