Scribd
Upload
278 views2 pages

SNAP Hydrophonics Basics

1. This document provides instructions for setting up a hydroponic system using the SNAP method, including establishing seedlings, preparing seedling plugs and growing boxes, and running the hydroponic system. 2. Key steps include filling trays and cups with growing media, sowing seeds, transferring seedlings to cups, drilling holes in styrofoam boxes, placing cups in the boxes filled with nutrient solution, and replenishing the solution as the plants grow. 3. The system is designed to receive morning sunlight for best plant growth, with covers and shelters used to prevent rain from entering and insect damage. Nutrient solutions are prepared using SNAP A and B formulas and

Uploaded by

nuancetrozepar
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
278 views2 pages

SNAP Hydrophonics Basics

1. This document provides instructions for setting up a hydroponic system using the SNAP method, including establishing seedlings, preparing seedling plugs and growing boxes, and running the hydroponic system. 2. Key steps include filling trays and cups with growing media, sowing seeds, transferring seedlings to cups, drilling holes in styrofoam boxes, placing cups in the boxes filled with nutrient solution, and replenishing the solution as the plants grow. 3. The system is designed to receive morning sunlight for best plant growth, with covers and shelters used to prevent rain from entering and insect damage. Nutrient solutions are prepared using SNAP A and B formulas and

Uploaded by

nuancetrozepar
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

HOW TO SET-UP SNAP HYDROPONICS 1

PJA Santos and ETM Ocampo Institute of Plant Breeding-CSC-CA, UP Los Baos
A. Establish the seedlings Materials needed 1. sowing tray shallow box/basin with holes for drainage at the bottom 2. growing media aged (not the new one) coconut coir dust or charcoaled rice hull or their mixture; saw dust (possible with the old stock not the new ones but not yet tested), fine sand (can be combined with coir dust and or charcoaled rice hull) 3. seeds (buy from your local aggie store) 4. watering solution (water with SNAP nutrient solution) Procedure 1. Fill the sowing tray with a layer of the growing media (about1 inch thick) 2. Level the media 3. Scatter the small seeds uniformly and thinly (the amount depending on your need) 4. Water liberally as needed (Expect germination in 3 to 5 days) 5. Grow the seedlings for 10 days before transferring to individual growing cups (called seedling plugs) B. Prepare the seedling plugs Materials needed 1. Styrofoam cups (8 to 10 oz) 2. Cutter or knife or hack saw blade 3. growing media 4. seedlings 5. BBQ stick or the like Procedure 1. Prepare the Styrofoam cups as shown . Use a knife or cutter to make those 8 holes (about 1 inch long at the side and inch at the bottom). 2. Fill the prepared holding cups with the growing media (about inch thick) 3. Transplant the seedlings from the sowing tray. Dig a hole in the middle of the growing media in the cup. . Use the a stick to uproot the seedlings from the sowing tray with care. Transfer only one seedling per cup. Make the transferred seedling stand firmly by replacing the dug media to the base of the seedling. 4. Water the seedling plugs carefully and lightly. C. Prepare the growing boxes Materials needed 1. Styrofoam boxes ( boxes of imported grapes} 2. Tin can (with open top and bottom) of big evap milk 3. Polyethylene plastic bag (20 x 30, 0.003 mm thick)

This publication is an output of the DA-BAR funded project on Promoting SNAP Hydroponics as a
Sustainable Food Production System for Urban Areas being implemented by the Institute of Plant Breeding, CSC-CA, UP Los Baos. Revised October 6, 2008

Procedure: 1. Make 5-6 (for small styro boxes) or 8 (for big styro boxes) holes on the lid/cover of the box using the tin can as hole puncher (See picture). 2. Use the plastic bag as liner for the bottom half of the box to make it fit to hold the nutrient solution D. Running the SNAP hydroponics system Materials needed 1. seedling plugs 2. SNAP nutrient solution 3. growing boxes with 10 liters of water each 4. benches or stand (optional) where the growing boxes will be placed under a shelter 5. rain shelter (optional during dry season) or roof awning facing east for the earliest and longest sunlight possible) Procedure 1. For good growth of the plants, locate the SNAP hydroponics where it will best receive the morning sunlight, the earlier the better. It should be under a roof awning if not a transparent shed to prevent the rain water getting into the system. 2. Arrange the growing boxes on the bench (optional) with covers removed 3. Fill each growing box with about 10 liters of tap water 4. Add 50-75 ml of SNAP A to each box stir well 5. Add equal amount of SNAP B to each box then stir well again 6. Put back the cover of the box 7. Place the seedling plugs into the holes of the cover. See to it that all cups are plugged in the holes evenly. 8. See to it that the bottom of the cups is touching the nutrient solution by inch deep, not any deeper or shallower. If not, add more water until the desired depth is reached. 9. Examine the boxes for leaks and make some troubleshooting. 10. Visit the set up every morning as early as you can to catch any insect larva that may eat the plants (the larva is visible in the early morning; after that they tend to hide from the sun and maybe harder to find) Expect the nutrient solution level to recede faster when the plants are much bigger than when they were still seedlings. Replenish using fresh nutrient solution when its level has gone down by more than 1 inch below the cup bottom. However, NEVER allow the level of the solution to again reach the bottom of the cup; replenish until the solution level has reached about 1/2 inch below the cups bottom. NOTE: It is more practical to prepare the nutrient solution in a drum and then just distribute the prepared solution to each growing box and use the left-over solution for replenishing.

For more information, please contact: Physiology Section Institute of Plant Breeding, UP Los Baos (049) 576-0024 or Directors Office Institute of Plant Breeding UP Los Baos (049) 536-5287

or

E-mail to: [email protected] [email protected]

You might also like