Scribd
Upload
112 views

All in One Tester Circuit (Tentative Report)

Roki Howladar submitted a project report on designing an all-in-one tester circuit to test electronics components. The circuit uses two transistors and a bi-color LED to indicate test results. It can detect polarity, continuity, and logic gate functionality. The simple circuit allows beginners to easily understand component testing. Test results are displayed by either the red or green half of the LED illuminating. The report documents the circuit design, components, diagrams, working principle, and test procedures for various components.

Uploaded by

Apurv Sharma
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
112 views

All in One Tester Circuit (Tentative Report)

Roki Howladar submitted a project report on designing an all-in-one tester circuit to test electronics components. The circuit uses two transistors and a bi-color LED to indicate test results. It can detect polarity, continuity, and logic gate functionality. The simple circuit allows beginners to easily understand component testing. Test results are displayed by either the red or green half of the LED illuminating. The report documents the circuit design, components, diagrams, working principle, and test procedures for various components.

Uploaded by

Apurv Sharma
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 14

ALL IN ONE TESTER CIRCUIT

Report submitted on fulfilment for the first semester Project of


Master of Science
in
Physics

Submitted By:
ROKI HOWLADAR (2022PGPHPH29)
M.Sc.(Physics), 1st Sem.

Under the Guidance of


DR. NEHA AGNIHOTRI,
Department of Physics.

Department of Physics,
NATIONAL INSTITUTE OF TECHNOLOGY,
JAMSHEDPUR. (2022-2024)
CERTIFICATE

This is to certify that the first semester project report entitled “ALL IN ONE
TESTER CIRCUIT” is a bona-fide work submitted by:
Roki Howladar (2022PGPHPH29)

in partial fulfilment of the requirement for the award of Master of Science in


Physics during session 2022-2024 at National Institute of Technology,
Jamshedpur is an authenticate work carried out by them under my supervision
and guidance.

To the best of my knowledge, the matter embodied in the project has not been
submitted to any other University/Institute for award of any degree.

______________________

Dr. Neha Agnihotri


Assist. Professor
Department of Physics

i
ACKNOWLEDGEMENT
We would like to express our immense sense of gratitude to our guide, Dr.
Neha Agnihotri, Department of Physics for their valuable instructions,
guidance, and support throughout our minor project.

And finally, we would like to thank again Dr. Hiralal Yadav, Head of the
Department, Department of Physics for his continued drive for better quality in
everything that happens at National Institute of Technology, Jamshedpur. This
report is a dedicated contribution towards that greater goal.

Roki Howladar (2022PGPHPH29)

1.
INDEX
1. AIM 3
2. INTRODUCTION 3
3. CIRCUIT COMPONENTS 4
4. CIRCUIT DIAGRAMS 5
5. WORKING 6
6. RESULT: ALL IN ONE TESTER CIRCUIT 7
7. LED STATUS (VARIOUS TESTS) 7
8. CONCLUSION 11

2
AIM

To design an all in one tester circuit.

INTRODUCTION
All in one multi-tester is quite expensive which may not be affordable for every
electronics beginners. Now, here is a cheap all in one tester circuit that can be used
to test the condition of almost all the electronics component from basic resistor to
advance ICs. The circuit all in one tester is used to detect polarity, continuity, logic
gate and also activity of multivibrator.
The circuit of all in one tester is so simple that it can be understand by beginners.
The circuit of all in one tester contains two transistor and very few other passive
components. Transistor T1 and T2 is used here as switch, driving the one half of
bicolor LED each in order to give result of the test.

3
CIRCUIT COMPONENTS

 +9V supply voltage

 BC548 NPN Transistor

 1 µF, 63V (Electrolytic Capacitor)

 3 Resistors of 2.2 KΩ,1.2KΩ and 4.7KΩ.

 On/Of Switch

 Bi-color LED

 IN4001 Diode

4.
CIRCUIT
DIAGRAM
5
WORKING
Initially, the circuit is in off mode, when switch SW1 is pressed, transistor T1 stops
conducting due to lack of forward bias. At the same time transistor T2 takes base
bias voltage from the battery through resistor R1 and conducts. This allows the red
half of bicolor LED1 to illuminate.
Transistor T1 conducts when the positive voltage through resistor R3 is given to
base of transistor T1 and light up the green half of LED1. In conduction of
transistor T1 transistor T2 turns off and vice-versa.
Thus from the description, we know that the functioning of the circuit thus depends
on the signal obtained at the base of transistor T1. The table below gives the testing
procedure for various components with the expected indication or result.

6.
RESULT

ALL IN ONE TESTER CIRCUIT

Bi-Color LED Status for Various Tests


Component/test Test LED1 Status Result Note
Procedure

Continuity Red and black Green ‘on’ Continuity


probes to the
test points Red ‘on’ No Continuity

7
8
The led glows green indicating the continuity of the wire connected to the red
probe and black probe.

9
The led glows green indicating the resistor is working correctly.

The led does not glows indicating the resistor is faulty.

10
CONCLUSION

Hence, by developing this project we were successfully able to detect


polarity, continuity and logic sate condition of almost all the electronics
component from basic resistor to advance ICs. The circuit is easy to
make with all the components used are cheap and basic. It is the perfect
circuit for a beginner to learn the basic principle of the working of a
multimeter.

11.

You might also like