MAHARASHTRA STATE BOARD OF

TECHNICAL EDUCATION, MUMBAI

MSBTE NORMS AND STANDARDS

FOR EQUIPMENTS AND
MACHINERIES
(2012-2013)

NAME OF THE COURSE / COURSE GROUP

MECHANICAL ENGINEERING
(ME)

(AICTE Approved Course)

1
 INDEX
Sr. No. Essential equipment Lab. Wise Page No.
1 Thermal and Power Engineering 3

2 Drawing and Design 6

3 Theory of Machines 9

4 Refrigeration & Air Conditioning 11

5 Mechanical Measurement & Control Lab 12

& MQC Lab

6 Fluid Mechanics & Machinery, Fluid Power 15

7 Automation 17

8 Electrical Engineering 19

9 Basic Electronics & Mechatronics 21

10 Production 23
11 Manufacturing Processes & Advanced Manufacturing 25
Processes

Sr. No. Desired Equipment Lab. Wise Page No.

1 Thermal and Power Engineering 27

2 Drawing and Design 30

3 Theory of Machine 31

4 Refrigeration & Air Conditioning 32

5 Mechanical Measurement & Control & 32

MQC

6 Fluid Mechanics & Machinery, Fluid Power 34

7 Automation 35

2
 ANNEXURE - I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY
(Essential equipment/ Hand Tools)
(Required for conducting thePractical)
1. Name of course/ Department:- Mechanical Engg. Dept.
2.Name of laboratory : Thermal & Power Engineering
Minimum
Remark if
Sr. No. Name of Equipt./Machinery Technical Specifications Qtty./Nos.
any
Required
1 An experiment set up on solar flat 0 1
100 litre, 60 C
plate collector used for water heating

2 Photo voltaic cell panel. Working Model(10Watt.) 2

3 Box type Solar cooker.(Standard) Working Model(4-pots.) 2
4 Model of horizontal axis wind mill Actual working Model
(Different rotor style)
5 Model of a biomass/ biogas plant Cut section Model 2
6 Chart showing various waste heat Plastic coated sheets for charts of 2
recovery devices. size 3 feet X 3 feet
7 Chart showing various types of Plastic coated sheets for charts of 2
Wind mills size 3 feet X 3 feet
8 Chart showing various types of Bio- Plastic coated sheets for charts of 2
gas plants size 3 feet X 3 feet
9 Old Working model of four-wheeler four stroke three/ four cylinder. 1
Engine

10 Old Working model of Two-wheeler Two/ four stroke single cylinder. 1

Engine
11 Working Model of Two-wheeler & four-wheeler 1 each
i)single plate coil spring
ii) diaphragm spring type clutch.

12 Working Model of synchromesh 3 forward & 1 reverse gear. 1

gearbox

13 Working Model of differential. for car/ truck engine 1

14 Working Model of Steering gearbox i)rack & pinion steering gearbox 1 each
ii) power steering

15 Working Model of suspension rigid axle suspension Mech/ 1

Hydrualic )
16 Working Model of hydraulic brake With master cylinder. 1
system
17 Battery and charging system Capable of charging 2-wheeler 1
multimeter. and 4-wheeler battery
18 LPG / CNG kit Standard kit with all accessories 1
suitable for 4-wheeler of min.
3
30kg. Capacity
19 Single cylinder air cooled petrol 3HP,3000RPM,Electric 1
engine with heat balance sheet Dynamometer
20 Multicylinder Diesel/Petrol engine 10HP, water cooled,1500rpm. 1
for Morse test arrangement

21 Exhaust gas Analyzer for petrol / showing percentage of CO,CO2 1

diesel engine NOX , ppm
22 Two-stage Reciprocating air 1
compressor Test Rig. Pressure-10kgf/sq cm
Displacement -5meter cube/min
Speed- 100RPMwith Air cooled
Intercooler, Motor-7.5HP with
arrangement of Torque Arm and
spring Balance

23 Vapour compression refrigeration Chillar capacity 20lit , 1

system test rig hermatically sealed comp.-0.3
HP with air cooled condensor
1/2 hp, rotameter-100lit./hr, filter
dryer, digital voltmeter and
ammeter and temp. indicator,
evaporator brine tank capacity
20lit.Energymeter
24 Solar water heating system test rig Heating water of capacity - 100 1
Litres with single cover Flat
plate collector size 3feet X 3feet

25 Model & Chart of Models of Acrylic / Aluminium 1 Each

i) Babcock & wilcox Boiler material Plastic
ii) Cochran Boiler coated sheets for charts of size 3
iii) Lancashire Boiler feet X 3 feet
iv)Loeffler boiler
27 Model & Wall Chart's of Boiler Models of Acrylic / Aluminium 1 Each
Mountings :- material Plastic
i) Water level indicator coated sheets for charts of size 3
ii) Steam stop valve feet X 3 feet
iii) Spring loaded/ Dead Weight
Saftey Valve
iv) Fusible Pulg
v) Feed check Valve
vi) Blow off cock
vii) Bourdon Pressure gauge.
26 Wall Chart's of Boiler Accessories Plastic coated sheets for charts of 1
:- size 3 feet X 3 feet
i) Economiser
ii) superheater
iii) Air Filter

4
27 Thermal conductivity of metal rod Brass/steel rod length 1
, Test Rig. 400mm,dia 20-30
mm,cylindricalshell,, cooling
water chamber , digital
voltmeter,ammeter,temp
indicator dimmerstat.
Thermocouples,stop watch

28 Experimental Setup of Stefan- Speciman disc m.s.150 mm 1

Boltzman’s law dia., speciman copper/brass of
20mmdia,1KVA Geyser,
Thermocople , Digital
voltmeter ammeter,temp
indicator, inlet outlet water
valve.
29 Model & Wall Chart's of Models of Acrylic / Aluminium 1 Each
I)Radiator, ii)Evaporators, material Plastic
iii)Condensers, iv) plate heat coated sheets for charts of size 3
exchangers feet X 3 feet

30 Cut section working models

of IC Engines-
i) 2 stroke engine with gear Scooter/motorcycle 1.5BHP 1
box and clutch
ii) 4 stroke 4 cylinder Car engines 20-40 BHP 1
diesel/petrol engine with
cooling and lubrication
systems
31 Models and Charts of –
i) Gas turbine system Models of acrylic or aluminium
ii) Turbo prop engine material. Standard charts of 1 each
iii) Turbo jet engine plastic coated sheets
iv) Ramjet Size 3ft x 3ft
32 Charts of – Standard charts of plastic coated 1 each
i) Car suspension system sheets
ii) Battery charging system Size 3ft x 3ft
33 Charts of – Standard charts of plastic coated 1
- different types of solar sheets
energy collectors Size 3ft x 3ft

5
 ANNEXURE - I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY
(Essential equipment/ Hand Tools)
(Required for conducting thePractical)
1. Name of course/ Department:- Mech. Engg. Dept.
2.Name of laboratory : Drawing and Design Lab'.

Minimum
Remark if
Sr. No. Name of Equipt./Machinery Technical Specifications Qtty./Nos.
any
Required
Charts showing Auxiliary views of With first angle method of 03 set
1
any three object. projection.
2 Models of Intersection of solids i) Cylinder to cylinder 02 Each
penitration.
ii)Cylinder to prism. iii)Cone to
Cylinder iv) prism to
prism.
Model & charts of Developments of Developments of Lateral 02 Each
3 Surfaces. surfaces of cube, prisms,
cylinder, pyramids & cone
4 Standard chart for Conventional i) Materials 02 Each
Representation ii)break in pipe, rod and shaft.
iii) Ball and Roller bearing, pipe
joints, cocks, valves, internal /
external threads. iv)
Various sections- Half, removed,
revolved, offset, partial and
aligned sections
v) Knurling, serrated shafts,
splined shafts , and chain wheels.
vi) Springs with square and flat
ends, Gears, sprocket wheel
vii) Countersunk &
counterbore.
viii) Tapers
ix)Surface roughness
x) Welding
Standard chart for Limits, Fits and Standard chart 2
5
Tolerances
6 Model & charts of Assembly 1. Couplings – Universal 02 Each
(Detailed part drawings) couplings & Oldham’s Coupling
2. Bearing – Foot Step Bearing
& Pedestal Bearing
3. Lathe tool Post
4. Machine vice & Pipe Vice
5. Screw Jack
6. Steam Stop Valve

6
7 Model & charts of Assembly to 1. Pedestal Bearing 02 Each
Details 2. Lathe Tail Stock
3. Drilling Jig
4. Piston & connecting rod
5. Gland and Stuffing box
Assembly
6. Valve – Not more than eight
parts
7. Fast & loose pulley
8 Cut section model of 3D object 3D object having slot, circular 10 different
hole, etc. model
Model & charts of Solids of Prism, Pyramid, Cone, 02 Each
9
Cylinder, Tetrahedron & Cube
10 Model & charts of Sections of Solids Sections of Solids Prism, 02 Each
Pyramid, Cone, Cylinder,
Tetrahedron & Cube
Model & charts of Developments of Developments of Lateral 02 Each
11 Surfaces. surfaces of cube, prisms,
cylinder, pyramids & cone
12 Model & charts of Free hand Free hand sketches of nuts, bolts, 02 Each
sketches rivets, threads, split pin,
foundation bolts, keys and
couplings.
CAD Software Auto CAD latest version or any Any 1 SHEET
13 CAD software with 10 Users
lience.
14 working models of i) Cotter Joint, working models / Acrylic / 01 each
ii)Knuckle Joint, iii)Bell Crank Aluminium Cast
Lever, iv)Turn Buckle, v)Off – Set
link, vi)Pulley
Working models of working models / Acrylic / 01 each
Shaft,(solid,hollow,spline) Aluminium Cast
Keys,(parrallel ,taper,feather,tangent
,woodruff etc.)
15 Power Transmission devices:-belt
drive,Chain drive.Gear drive,
Clutches, gear
trains,Coupling(rigid,Flexible).

16 Working models of Bearings Ball bearings-single, double

row, angular contact and thrust,
Rolling contact bearings-
cylindrical, Taper roller, thrust,
Pedastal, Journal, Pivot
bearings,
wall charts Tolerances, surface
17
finish, Limits, Fits

7
 18 Models of Lead screw of lathe, Metallic models
feed screws of machine tools,
Clamping screws, Toggle Jack
screw, Screw jack
19 Wall charts of Helical Springs, Plastic coated Wall Charts of
bolted joints, Welded joints helical compression and Leaf
Springs of different types,
different types of screw joints
and welded joints
20 Wall chart of types of levers – bell working models / Acrylic /
crack lever, rocker arm, compound Aluminium Cast
lever, brake pedals
21 Models and wall charts of – working models / Acrylic /
Loci of points-involute, cycloid –epi Aluminium Cast
& hypocycloid, four bar mechanism

Note: All charts should be plastic or acrylic coated – size 3ft x 3 ft

8
 ANNEXURE - I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY
(Essential equipment/ Hand Tools)
(Required for conducting the Practical)
1. Name of course/ Department:- Mech. Engg. Dept.
2.Name of laboratory : Theory of Machine

Minimum
Remark if
Sr. No. Name of Equipt./Machinery Technical Specifications Qtty./Nos.
any
Required
1 Model of quick return mechanism of Wooden /Aluminium die 1
a shaper machine. Cast/Acrylic Models
2 Model of Inversion i)Single Wooden /Aluminium die 1 Each
Slider Crank chain ii)Rotary I.C. Cast/Acrylic Models
Engines mechanism iii)
Whitworth quick return
mechanism
iv)Crank and Slotted lever quick
return mechanism
iv)Double Slider Crank Chain
v) Scotch Yoke Mechanism
vi) Oldham’s Coupling.

3 Model of Wooden /Aluminium die 1 Each

i) Bicycle free wheel Sprocket Cast/Acrylic Models
mechanism.
ii)Geneva Mechanism.
iii) Ackerman’s Steering gear
mechanism
iv)Foot operated air pump
mechanism
4 Models of Different types cam & Wooden /Aluminium die 1 Each
Followers- eccentric camps, tangent Cast/Acrylic Models
camps, roller and knife age followers
5 Model of governor Wooden /Aluminium die 1 Each
i) Fly ball governor Cast/Acrylic Models
ii) Watt governor
iii) Porter governor
iv) Hartnell governor
6 Models of Mechanically Wooden /Aluminium die 1 Each
operated braking mechanism Cast/Acrylic Models
for two wheelers.
i) shoe brake
ii) Band Brake
iii) Internal expanding shoe
brake

9
7 Models & Charts of Wooden /Aluminium die 1 Each
Dynamometer Cast/Acrylic Models
i) Rope Brake Dynamometer
ii) Hydraulic Dynamometer
iii) Eddy current Dynamometer.

8 Models & Charts of Clutch Wooden /Aluminium die 1 Each

i) Single plate clutch Cast/Acrylic Models
ii) Multiplate clutch
iii) Centrifugal Clutch
iv)Cone clutch
v) Diaphragm clutch.
Vi)Multiplate clutch.
9 Balancing of several masses rotating weight of rotor from 0.5- 1
in a single plane Test rig. 10kf.,dia-500mm,dist
betweenbearing centres-
400mm,balancing speed-1200

10
 ANNEXURE - I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY
(Essential equipment/ Hand Tools)
(Required for conducting thePractical)
1. Name of course/ Department:- Mech. Engg. Dept.
2.Name of laboratory : Refrigeration & Air Conditioning.
Minimum
Remar
Sr. No. Name of Equipt./Machinery Technical Specifications Qtty./Nos.
k if
Required
any
1 Water cooler test rig.(100 Ltr.) capacity 60 lit. hermatically sealed 1
comp.-0.6 HP with air cooled
condensor 1/2 hp, rotameter-
100lit./hr, filter dryer, Energymeter
,digital voltmeter and ammeter and
temp. indicator, evaporator tank
capacity 60lit.
2 Ice plant test rig. capacity 20kg/day , hermatically 1
sealed comp.-0.3
HP with air cooled condensor
1/2 hp, rotameter-100lit./hr, filter
dryer, digital voltmeter and ammeter
and temp. indicator, evaporator brine
tank capacity 20lit.
3 Working Domestic refrigerator. 160 litre 1

4 RAC Controls i) L.P./H.P. cut outs ii) 1 Each

Thermostat
iii) Overload protector,
iv)solenoid valve .
5 Working Hermetically 1 Tonne capacity 1
sealed compressor.
6 Air Conditioning test rig. 1 Tonne capacity with air cooled 1
condensor cooling fan
0.1 hp, rotameter-100lit./hr, filter
dryer, digital voltmeter and
ammeter and temp. indicator,
evaporator
7 Working Window Air Conditioner Normal cooling capacity 2.0 1
Ton, 6000 Kcal/hour, 24000
BTU/hour, Single phase 230 volts
voltage, frequency 50 Hz
8 Cut section model of Hermatically 1 tonne capacity 1
sealed compressor
9 Refrigeration equipment Pipe bending, swaging tool, spanner 2 sets
maintenance tool kit set, pipe cutter, charging manifold,
flexible hoges with quick actiting
couplings, pressure gauges

11
 ANNEXURE - I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY
(Essential equipment/ Hand Tools)
(Required for conducting thePractical)
1. Name of course/ Department:- Mech. Engg. Dept.
2.Name of laboratory : Mechanical Measurement and Control Lab & MQC Lab.

Minim
Sr. No. Name of Equipt./Machinery Technical Specifications um
Qty./No
A) Mechanical Measurement & Control Lab'.

1 Strain guage trainer (strain /force Sensor-four arm bridge with strain guage
measurement) mounted on cantilever 2kg
1
Display 3.5digit digital display

2 Measurement of speed using Sensor -inductive and optical sensor with

optical and inductive (magnetic) sensor assymbly with speed motor Display
1
transduser 3.5digit digital display
3 Rotameter trainer for flow Sensor -stadenert glass rotameter,
measurment process tank with motor pump Display-
float position on graduated scale 1
4 Displacement measurment using Sensor -inductive (non linear) solenoid type
inductive transducer on board with micrometer, micrometer
screw guage assembly for displacement ,
bridge balance type circuit 2
Display3.5digit digital display
5 Temperature measurment and Sensor- type k (Cr- Al)thermocouple,
control using thermocouple sensor assemblyand water bath with
heating arrengement Display3.5digit digital 2
display
6 Temperature measurment and Sensor- PTC thermister, sensor
control using thermister assemblyand water bath with heating
arrengement Display3.5digit digital display 2
7 Thermocouple for temperature and humidity
measurementwith probe range - 2
50to+50 deg. Cent.
8 Bi metallicThrtmometer -20 TO +70 DEG. CENT. 2
9 Multidigital stratoscope cum upto 5000 rpm
tacometer for speed measurement 2
10 Bourdon tube trainer sensor - Bourdon tube C type with LVDT
Display 3.5 digit display for pressure/
2
displacement

12
 11 Level Measurement using sensor capacitive Type,
capacitive Transducer sensorassembly with glass jar
2
fitted with water tap. Display
3.5 digit display
13 Flow measurement using optical Standard disc optical sensor,
2
transducer Display 3.5 digit display.
14 MCLeod guage with high McLeod guage with 1
vacuum pump / Bourdon tube arrangement for high pump
15 Stroboscope Range upto 5000 RPM 1
display – LED digital
16 Inductive pickup for speed Sensor – inductive , variable 1
measurement speed motor arrangement,
3.5 digital display
17 Load cell Censor-4 arm bridge with 1
strain guage capacity-2 kg,
3.5 digital display
B) MQC Lab

1 Radius gauge Metric Set 02

2 Pitch screw gauge Metric and BSW 02
3 Filler gauge Metric Set 02
4 Vernier caliper 200mm LC 0.02 06
5 Vernier Caliper 300mm LC 0.02 02
Digital Venier Caliper 150mm L.C = 0.01mm
6 Vernier Height gauge 300mm LC 0.02 02
7 Vernier Depth gauge 200mm LC 0.02 02
8 Dial type vernier caliper 150mm LC 0.05 02
9 Outside Micrometer 0 -25mm LC 0.01 04
10 Outside Micrometer 25-50mm LC 0.01 04
11 Inside Micrometer 25- 75mm LC 0.01 02
12 Tube micrometer 0-25mm LC 0.01 01
13 Slip gauge set Metric 76 pieces workshop 02
grade
14 Adjustable snap gauge 25 -45mm,50 -65mm, 01 of each
dimension
15 Plug gauge 25 H 7 01
16 Ring gauge 40 p6 01
17 Dial Indicator 0.01mm & 0.001mm 02 of each
18 Comparator Stand Small 60x 60mm table 04
19 High pressure pneumatic Accurate make differential 01
comparator Dial Type design Scale range 20mm &
scale division 0.5mm with Air
Plug Gauge and Two Master
Ring Gauges and Air Ring
Gauge and Two Master Plug
gages of suitable dimension and
a set of 10jobs corresponding to
that dimension.
20 Sine bar and Sine center 100, 200, 300mm 01 each
21 Dial stand adjustable Single knob adjustment 02
22 Screw thread micrometer 0-25mm and 25 -50mm With 01 of each
set of interchangeable Anvils
( m1 to m 06)

13
23 Floating carriage micrometer With set of setting cylinders, set 01
of wires and other accessories
24 Gear tooth vernier 50mm, 2 to 25 module 04
25 Optical profile projector 20X, 40X magnification 01
26 Test dial indicator Range 10.3mm , 0.002 mm 02
27 Test mandrel Parallelism in 10microns 01
28 Angle dekkor with set of Angle Accuracy 1 minute 01
Gauges
29 Surface roughness measurement Ra, Rz digital with sample 01
(surftest) length adjustment setting
30 Surface Plate (Granite/cast iron) 400x400mm Grade I 04
31 Vernier Bevel protractor LC= 5sec 02
32 Set of angle gauges in degrees, minutes, seconds 01 set
(13 pieces)
33 Autocalimeter With standard accessories like
plain reflector, optical square,
instrument base with leveling
attachment, magnification10x ,
LC=1 sec
34 Optical flat 25mm , 50mm 1 each
35 Sprit level block Base length 250 mm, bubble
size 10 sec
36 Comparators Magnification 200x/500x 1 each
i. Mechanical comparator
ii. pneumatic comparator
iii. Electrical comparator
37 V Block 900, 1200 1 each

38 Charts 6 sigma, 1 each

Normal distribution curve
Sampling plan chart

14
 ANNEXURE - I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY
(Essential equipment/ Hand Tools)
(Required for conducting thePractical)
1. Name of course/ Department:- Mech. Engg. Dept.
2.Name of laboratory : Fluid Mechanics & Machinery, Fluid Power

Mini
Sr. No. Name of Equipt./Machinery Technical Specifications mum
Qtty./
A) Fluid Mechanics & Machinery

1 i)Bourden pressure gauge 2 01

10 Kgf./cm
ii)Dead Weight Pressure gauge. Each
2 Experimental setup of Bernoulli’s Apparatus for verification of Bernoulli’s Theorem 1
Theorem complete with tank
3 Venturimeter Test Rig Venturimeter 1
( cast iron /Brass ) 25mm & 50mm.
4 Orifice meterTes Rig Apparatus to determine of CD,CV, CC,OF Orifice 1
with accessrios like collection tank, stand, scale &
slide attachment.
5 Hydraulic Bench Setup for (Major Apparatus to determine looses in pipe due sudden 1
& minor looses in pipe.) enlargement & contraction with all accessrios such
as collecting tank & differential manometer.
6 Pelton wheel Test rig PELTON WHEEL TURBINE TEST RIG - 1.3 HP 1
(1 Kw) Capable to visualise the operation
& estimate B. H. P. & W. H. P. and various
efficiencies of pelton turbine. Pelton wheel
connected to a rope brake. Water supplied by
centrifugal pump & flow measured by
venturimenter & mercury manometer. Water jet is
directed over the buckets by a nozzle & a spear
operating inside the nozzle controls the water flow.

15
7 Centrifugal pump Test rig CENTRIFUGAL PUMP TEST RIG AT 1
CONSTANT SPEED- 5 HP capacity 1500 RPM –
Centrifugal pump, provided with three phase motor,
vacuum gauge at suction and pressure gauge on
discharge pipe, gate valve at discharge, which
facilitate estimation of pump performance at various
discharge heads.
AC MOTOR & PULLEY MOUNTED – As per
constant speed type, only pump is provided with a
three speed pulley, gate valve at discharge to vary
the head. DC MOTOR VARIABLE SPEED —As
per constant speed type, only pump is provided with
a variable speed drive and gate value at discharge to
vary the speed.
8 Reciprocating pump Test rig RECIPROCATING PUMP TEST RIG – 1
A recirculating type unit with reciprocating pump
and vacuum gauge & pressure gauge at discharge by
measuring input to motor
and output of pump performance can be estimated
at three different speed by using pulley.

B) Fluid Power
9 Model / charts of Pumps centrigugal pump, Reciprocating Pumps, Vane 1 Each
pump, Gear Pump
10 Model / charts of Valves Pressure control valves – pressure relief valve, 1Each
pressure reducing, pressure unloading,
Direction control valves – Poppet valve, spool
valve, 3/2, 4/2 D.C. valves, Sequence valves.
Flow control valves – pressure compensated, non
pressure compensated flow control valve.
11 Model / charts of Actuators Actuators - Rotary Actuators - Hydraulic motors 1Each
Linear Actuators – Cylinders - single acting,
double acting

16
12 Model / charts of Hydraulic Circuits Hydraulic Circuits - 1 Each
i)Meter in&Meter out circuits . ii)Bleed off circuit
iii)Sequencing circuit
iv) Hydraulic circuits for Milling machine&Shaper
machine, v)Motion synchronization
circuit.
13 Charts of Hydraulic & Punematic Plastic coated sheet Charts of Hydraulic &
symbols. Punematic components symbols.

14 Charts of Compressor & Control Compressor – Reciprocating & Rotary 1 Each

Valves compressors
Control Valves – Pressure regulating valves,
Flow Control valves, Direction Control Valves.
15 Charts of Pneumatic Circuits Pneumatic Circuits 1Each
i) Speed control circuits. ii)Sequencing
circuits.
16 Hydraulic Trainer kit Basic component such as--- Valves(3/2 & 5/2) 1
Profile plate , Pressure guage assembly, Dual
Pressure valve, shuttle valve, Flow Controll
valve , Cylinder (Single & double acting),
Filter Regulator with guage, Manifold
Assembly, Pressure Regulator, gear pump.

17 Puematic Trainer kit Basic component such as--- Valves(3/2 & 5/2) 1
Profile plate , Pressure guage assembly, Dual
Pressure valve, shuttle valve, Flow Controll
valve , Cylinder (Single & double acting),
Filter Regulator with guage, Manifold
Assembly, Pressure Regulator, etc.

17
 ANNEXURE - I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY
(Essential equipment/ Hand Tools)
(Required for conducting thePractical)
1. Name of course/ Department:- Mech. Engg. Dept.
2.Name of laboratory : Automation

Minimum
Remark if
Sr. No. Name of Equipt./Machinery Technical Specifications Qtty./Nos.
any
Required
1 Computer P4 Dual core,1GB Ram,80GB 20 Nos.
HDD,Optical Mouse, 17 " TFT
Monitor
2 Printer Laser Printer , 15ppm 1
3 Autocad Software Latest version 02 Sheets
Minimum 10
User Lience.
4 CNC Machine Turning Trainer Kit Swing overbed-150mm, Swing 01 Nos.
over cross slide-50mm,Centre
dist.-300mm,Capable of turning
Acrylic, Al,wood
etc.,compatable with FMS/DNC

5 CNC Machine Milling Trainer Kit 3-Axis,Travel X-300mm,Y- 01 Nos.

250mm,Z-125mm Capable of
milling Acrylic, Al,wood
etc.,compatable with FMS/DNC
6 LCD/DVD Projector 1200 /1500 Lumen (Min) 02 Nos.
7 White Screen 4feetX4feet 02 Nos.
8 Sensors Limit switches, proximity 1 each
switches like inductive
,capacitive and optical , Thumb
wheel switches magnetic reed
switches ,Optical encoders-
displacement measurement,
rotary, incremental, optocouplers
9 Actuators solenoids, relays,– DC motors, 1 each
DC brushless motors, AC
motors, stepper motors , servo
motors

18
10 PLC Trainer kit Digital I/O -14 Nos., Analog I/O - 1
04 Nos. With working model of
- Speed control of motor
- Motor start and stop by using
two different sensors
- Four road junction traffic
controller Lift control
- Washing machine control
- Tank level control
- Bottling plant

11 PLC Softwares - Ladder logix programing 10 User Licence Allen

- SCADA Bradlley,
Siemens
make
12 Electro pneumatic trainer kit. Basic component such as--- 1
Valves(3/2 & 5/2, ) Profile plate
, Pressure guage assembly , Dual
Pressure valve, shuttle valve,
Flow Controll valve , Cylinder
(Single & double acting), Filter
Regulator with guage, Manifold
Assembly, Pressure
Regulator,Proximity switch reed
contact, Pneumatic to Electric
convertor , Electrical limit
switch, Power supply
unit,Adoptor Set, Electrical
signal input , Relays , etc.

13 Electro hydraulic trainer kit. Basic component such as--- 1

Valves(3/2 & 5/2, ) Profile plate
, Pressure guage assembly , Dual
Pressure valve, shuttle valve,
Flow Controll valve , Cylinder
(Single & double acting), Filter
Regulator with guage, Manifold
Assembly, Pressure
Regulator,Proximity switch reed
contact, Hydraulic to Electric
convertor , Electrical limit
switch, Power supply
unit,Adoptor Set, Electrical
signal input , Relays , etc.

19
 MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY
(Essential equipment/ Hand Tools)
(Required for conducting thePractical)
1. Name of course/ Department:- Mech. Engg. Dept.
2.Name of laboratory : Electrical & Electronics Lab
Sr.n Quantity
Name of equipment Specification
o. required

1 Voltmeter, Meco- 0 to 300 v

01
Ammeter, Meco-0 to 5 amp
01
Wattmeter Meco-0 to 5 amp/0 to 300/600v
01
With required accessories

2 Dc shunt motor With required 200 v dc supply,3point starter with expt.set up

01
accessories

3 Head light 12 v/35 watt 01

Turn indicator 12 v/25watt 01

Horn with required accessories 12 v/20-40 watt 01

4 Resistor ,capacitor with colour code Resistor- 1 Ω -10kΩ, capacitor- 1pf-100 pf 05

of different values
05

5 Experiment kit to study truth table of Truth table for and,or,not,nand,nor

01
logic gates

6 Experimental kit for study of half and digital multimeter var-200 mv to 1000 v/200 µa 01
full wave rectifier with filter, to 10 a/200 Ω / 2000kΩ
multimeter. 01

7 Experimental kit for study of load Digital multimeter var-200 mv to 1000 v/200 µa
and line reguation using zener diode, to 10 a/200 Ω / 2000kΩ 01
multimeter.

8 Experimental kit for study of Strboscope

stroboscope with required 01
accessories.

9 Experimental kit for study of LVDT LVDT -0 to 5 cm, digital multimeter var-200 mv
kit with required accesssories, to 1000 v/200 µa to 10 a/200 Ω / 2000kΩ 01
Multimeter.

10 Experimental kit for study of strain Strain gauge 1 to 10 kg, digital multimeter var-200
01
gauge with required accessories mv to 1000 v/200 µa to 10 a/200 Ω / 2000kΩ

20
 MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY
(Essential equipment/ Hand Tools)
(Required for conducting thePractical)
1. Name of course/ Department:- Mech. Engg. Dept.
2.Name of laboratory : Basic Electronics & Mechatronics

Sr. Technical Minimum

No. Name of Equipment/ Trainer Kit Specifications Qty/ Nos

Required

01 Digital Multimeter 4.5 digit with R , V, I measurements, diode 06

and BJT testing

02 Analog Multimeter R , V, I measurements 06

03 Cathode Ray Oscilloscope or TFT 30 MHz dual trace 04

Oscilloscope

04 Digital Storage Oscilloscope 60 MHz dual trace, USB interface 02

05 Function Generator 3 MHz , sine, square, triangular and pulse 04

generator

06 Signal Generator 100 MHz, sine wave 01

07 LCR-Q meter L, R, C , Q , D measurements with four wire 01

method

08 IC tester Analog, digital IC testing 40 pins 01

09 Regulated power supply 0- 30 Volt, 2 A with digital display, with S.C. 06

protection

10 Dual tracking regulated power supply 0- 30 Volt, 2 A Variable 04

11 Robot Trainer Robot Robot simulation Software 01

( Robot simulation Software along with

hardware ,user manual & activity book )

12 Camera Trainer Trainer shall demonstrate automation / 01

mechatronics of camera

13 PLC Trainer PLC trainer hardware and software for ladder 01

programming , computer interface with digital
and analog I/O. switches , relay lamp

21
 operation

14 Trainer kits for digital ICs Trainer kit shall consists of digital ICs for 02
logic gates, flop flop, shift registers, counter
along with toggle switches for inputs and bi-
colour LED at outputs, built in power supply

15 Amplifier trainer kit BJT based two stage RC coupled amplifier, in 02

built power supply suitable to plot frequency
response with various test point and
transparent real panel .

Laboratory shall have discrete components of various ratings ‐‐ such as resistors, capacitors , inductors , diodes, BJT,
FET , SCR, UJT, TRIAC, DIAC , LED , Photodiode, IC 741, IC 555, seven segment display, switches , transformers ,
breadboard and cables.

Components shall store in stack component organizer.

22
 ANNEXURE - I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY
(Essential equipment/ Hand Tools)
(Required for conducting thePractical)
1. Name of course/ Department:- Mech. Engg. Dept.
2.Name of laboratory : Production

Minimum
Remark
Sr. No. Name of Equipt./Machinery Technical Specifications Qtty./Nos.
if any
Required
1 Break even analysis Chart Plastic coated sheet Chart 1
2 Process and Product Layout Chart Plastic coated sheet Chart 1

3 Chart showing different Material Types of conveyors,cranes, 1 each

Handling Equipments elevators & Hoists, Industrial
vehicles, motor vehicles, Rail
road cars, marine carriers ,
forklift truck, trolleys, Pipes,
Automated Guided Vehicles
(AGV’s)
4 Various types of control charts Control, Progressive Control, 1 each
Gantt chart.
5 Charts showing various recording Outline process chart, Flow 1 each
methods– . process chart, Two Hand process
chart, Multiple activity chart,
Flow diagram, String diagram,
Travel chart

6 Time Study Equipments. Stop Watch , Slide Rules 2

7 Economy Order Quantity Model Chart Showing --Inventory Cost 1
Chart relationship, Deciding Economic
Batch Quantity, EOQ Model,
Calculation of EOQ,
8 Charts showing various storage Storage systems – One bin , Two 1
systems– . bin system, Material issue
request (MIR), bin card.
9 Chart showing Principle of location 3-2-1 principle of location. 1
10 Chart showing Different types of Types of locators and clamping 1
locating and clamping devices devices.
11 Chart showing Different types of jigs Types of jigs and fixtures. 2
and fixtures.
12 Chart showing mechanics of chip Schematic representation of 1
formation machining process
13 Chart showing different types of chip Continuous,discontinuous,built 1
up chips
14 Chart showing different types of flank,crater,localised,chipping 1
wears off of the cutting edge
23
15 Chart showing different cutting Tool Single point cutting tool, drills , 1 each
Geometry reamers, milling cutters.
 16 Chart showing Tool Terminology Chart showing all tool angles 1
17 Chart showing different types of Simple Die, Compound Die, 1 each
Dies Progressive Die, Combination
Die.
18 Chart showing different types of Die blanking , piercing, shearing, 1 each
Operations cropping, notching, lancing,
coining, embossing , stamping,
curling, drawing, bending,
forming.
19 Chart showing Constructional Pressure Die casting dies, metal
features of various dies extrusion dies, injection 1 each
moulding dies, forging dies,
plastic extrusion dies .

Note: All charts should be of plastic coated sheets , size 3ft x 3ft

24
 ANNEXURE - I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY (Essential equipment/ Hand Tools) (Required for
conducting the Practical)

1. Name of course/ Department:- Production Technology

2.Name of laboratory : Manufacturing Processes

Sr Name of Equipment Technical Specification Min

No Qty

1 Centre Lathe Max. swing over bed : 350 mm 20

Admit between centres : 1000mm
Spindle bore : 52mm. Power of motor : 3HP, 3 phase,
50 Hz. With accessories.
2 Spot (Resistance) Welding Portable type spot welder rating 2.5 KVA for welding 1
Machine upto 2mm + 2mm M.S. Sheet, Max throat depth 20cms.
3 Radial Drilling Machine 0mm size, Any standard make with radial arm 1
movement 360 degree
4 Wood Turning Lather Floor model, complete with standard accessories and 1
electrical
Length of bed: 1800mm
Height of centre : 200mm
Distance between centre: 1200mm
HP of motor: 1AC 440V. 50hz 1440 rpm, Compound
saddke, o/s turning attachment, true chuck, live centre
5 Pattern Making and Mould Standard tools required for pattern making and mould 01
Making Tools making set

6 MIG Welding Equipment Power source with integral wire feeder and rear stand 1
for gas cylinder, for seam welding, spot welding, etc.
current range 35-160 amp, open circuit voltage range
16-31V, 3 phase, input KVA 4.5, current 9 amp, with
all accessories. Welding current at 60% duty cycle
160A / 22V, at 100 % duty cycle 125A / 21V. To weld
ferrous and non ferrous metal alloys with pre heater,
light and heavy duty gun assembly, cooling system and
all standard accessories.
7 T.I.G. Welding AC / DC Tig welding set for welding ferrous and non
Equipment ferrous alloys, Max surrent capacity 150 amp. Control
unit built in H.F. unit and controls, contractor, DC
suppressor, water circulatory unit, torch with
accessories box, set of tungsten electrodes, set of
welding accessories.

25
 ANNEXURE - I
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY (Essential equipment/ Hand Tools) (Required for
conducting the Practical)

1. Name of course/ Department:- Production Technology

2.Name of laboratory : Advanced Manufacturing Processes
Sr. Name of Technical Specification Min
No. Equipment Qty
1 Universal Milling Length x width of working table 1200mm x 700mm. 01
Machine Number of T-slots 6.
Longitudinal Traverse 1200mm. Cross Traverse
800mm. Table height from floor 940mm. Circular
movement of table 360deg. No.of spindles 7.. Manual
vertical adjustment of milling head 320mm. Swivel of
milling head on either side 45 deg. Throat clearance
915 deg (distance between main spindle and column
guide) Maximum diameter of circular milling
2600mm. Manual & Automatic feed. Accessories
Draw bar, circular millinghead, high speed milling
head, small radius milling head, Micro-depth stop
formilling head, circular dividing attachment for
rotary table, coolant equipment, special cutters, boring
tools, tool holder, form cutting, collets
2 Universal Dividing Head With centres, index pate, chuck 01
3 Hydraulic Surface Maximum grinding length 750mm.
Grinding Machine Maximum grinding width 250mm
Distance centre of wheel, over table 125mm
(maximum), Longitudinal travel speed 12meters
/minute. Standard wheel size 250mm x 25mm x
762mm. Speed of wheel 2100 or 2625 rpm.
Lubrication centralized Automatic. Accessories
Grinding wheel, wheel flange puller, wheel balancing
mandrel, table guards pump with fittings, machine
lamp, instruction manual, permanent magnetic chuck,
wheel balancing stand, coolant equipment magnetic
separator, demagnetizer, universal machine vices, dust
and exhaust equipment unit, wheel dressr over wheel
head.
4 Radial Drilling Machine 20mm size, any standard make with radial arm 01
movement 360 degree.

26
 ANNEXURE - II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY
(Desired Equipment/ Hand Tools) (Optional
Equipmentl)
1. Name of course/ Department:- Mech. Engg. Dept
2.Name of laboratory :-Thermal & Power Engineering
Minimum
Sr. No. Name of Equipt./Machinery Technical Specifications Qty./Nos.
Required
1 Phtovoltaic Silicon Pyranometer Capable of measuring solar radiation and instant
response of 10 Microsecond 1
3 Solar Lantern 10V Capacity 1
4 Solar operated household Appliances used to run 6W Bulbs & a fan 1
5 Manuals of different make for two wheeler & four wheeler 1
6 Wall charts of clutchs, gear box Wall charts of PVC / Acrylic material 1
drives Axels
7 Wall charts of Brake system hydraulic, Wall charts of PVC / Acrylic material 1
Pneumatic brakes. disc & drum brake.
8 Wall charts of Leaf spring, air Wall charts of PVC / Acrylic material 1
suspension,. McPherson & wishbone,
trailing link suspensions, telescopic
shock absorbers.
9 Wheel Alignment and Balancing Standard typecapableof balancing 4- 1
machine wheeler
10 Wall charts of Ignition system Wall charts should comprise of information on 1
Electronic and CDI ignition system.
11 Wall charts of Lighting system Wall charts should comprise of information on 1
head light, tail light, indicator light & their
circuits.
12 Working engine for assembling and 4-stroke multicylinder diesel/petrol 1
dismanteling (4 stroke)
13 Working engine for assembling and 2-stroke single cylinder diesel/petrol 1
dismanteling (2 stroke)
14 Working Domestic refrigertor for 180liters capacity 1
study and demonstration
15 Working window air conditioner for 1.tonne capacity. 1
study and demonstration
16 Cut sectional model of steam turbine Miniature metallic modell 1
17 Cut sectional model of steam Miniature metallic modell of 1
condenser Different Types of condenser.
18 Wall chart for diferent types of Wall charts should comprise of information on 1
nozzels Different types of nozzle with labelling.

27
19 Photovoltaic Pannel Suitable for lighting two tube 1
lights of minimum 40Watts
20 Wall chart of wind power Wall charts should comprise of 1
generation plant information on Working
principle along with different
components
21 Wall chart of Biogas plant . Wall charts should comprise of 1
information on Working
principle along with different
components
22 Wall chart of Hydraulic power Wall charts of PVC / Acrylic 1
plant. material
Size 3ft x 3ft
23 Wall Chart of Boiler :- Wall charts of PVC / Acrylic 1Each
I)Benson Boiler material Size 3ft x 3ft
ii) Lamont Boile
ii) VeloxBoiler
24 Wall chart of Themodynamic vapour Wall charts of PVC / Acrylic 1
process/Gas process material Size 3ft x 3ft

25 Wall chart of Geothermal Plant Wall charts of PVC / Acrylic 1

material Size 3ft x 3ft
26 Wall chart of Wall charts of PVC / Acrylic 1Each
i)BiogasPlant material Size 3ft x 3ft
ii) BiomassPlant
iii)Bio-diesel Plant
27 Wall chart of Nuclear Power Plant Wall charts of PVC / Acrylic 1
material Size 3ft x 3ft
28 Wall chart of Wall charts of PVC / Acrylic 1Each
i) Heat Engine material Size 3ft x 3ft
ii) Heat Pump
iii)Refrigerator.
29 Wall chart of Impulse and Reaction Wall charts of PVC / Acrylic 1
turbine. material Size 3ft x 3ft
30 Wall chart of Velocity & Pressure Wall charts of PVC / Acrylic 1Each
Compounding of steam Turbine. material Size 3ft x 3ft
31 Wall chart of Wall charts of PVC / Acrylic 1Each
i)Surface Condensor material Size 3ft x 3ft
ii) Jet Condenser
32 Wall chart of Cooling Towers:- Wall charts of PVC / Acrylic 1Each
i)Force draugh material Size 3ft x 3ft
tii)Natural draught
iii)Induced draught.
33 Wall Charts of – Wall charts of PVC / Acrylic 1Each
i) Rotary compressor material Size 3ft x 3ft
ii) Screw compressor

28
 ANNEXURE - II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY
(Desired Equipment/ Hand Tools) (Optional
Equipmentl)
1. Name of course/ Department:- Mech. Engg. Dept
2.Name of laboratory :- Drawing and Design
Minimum
Remark if
Sr. No. Name of Equipt./Machinery Technical Specifications Qtty./Nos.
any
Required
1 Auto CAD Software or ProE or Catia Latest version Any 1 SHEET
with 10 Users
lience.
2 Learing Software of Engg. Drawing Learing Software of Engg. 1
Drawing should comprise of
information on Self learing
Curriculum of Engg. Drawing.

3 CD/ Video Casettte of Engg. CD/ Viedio Casettte of Engg. 1

Drawing. Drawing. should comprise of
information on Self learing
Curriculum of Engg. Drawing.
4 Solidworks CAD Solidworks Any 1 SHEET
with 10 Users
lience.

29
 ANNEXURE - II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY
(Desired Equipment/ Hand Tools) (Optional
Equipmentl)
1. Name of course/ Department:- Mech. Engg. Dept
2.Name of laboratory :-Theory of Machine

Minimum
Remark if
Sr. No. Name of Equipt./Machinery Technical Specifications Qtty./Nos.
any
Required
1 Models of following Acrylic/ wood material/ 2 Each
Mechanism i)Four bar link Aluminium Cast.
Mechanism
ii) slider crank Mechanism
iii) Ellipse tracer model
iv) Inversions of four bar
mechanisms
v)Inversions of slider
crank mechanisms

2 Models of following Cams & i)Plate cam with flat face 2 Each
followers reciprocating follower .
i)Plate cam i) tanget cam with roller
ii) tanget Cam oscilating follower
iii) cylinderical cam iii) cylinderical cam with
iv) translating cam. translating follower
iv) translating cam. with
reciprocating knife edge
follower.

3 Model / chart of Bearing I)Ball Bearing 2 Each

ii) Roller Bearing
iii) Taper Bearing
iv) Thrust Bearing

4 Models of Power Transmission Models / charts of i)Belt 2 Each

i)Belt Drives Drives :-flat belt, V– belt
ii) Chain Drives ii) Chain Drives:- Chain &
iii)Gear Drives including reduction Sprocket wheels
gearbox,worm & worm wheel iii)Gear Drives :- Spur gear
iv) Rope Drives terminology, types of
Differentgears and gear trains
iv) Rope Drives :-Wire ropes etc.
5 Gyroscope Models Standard Gyroscope with 1
revolving stool.

30
 ANNEXURE - II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY
(Desired Equipment/ Hand Tools) (Optional
Equipmentl)
1. Name of course/ Department:- Mech. Engg. Dept
2.Name of laboratory :- Refrigeration & Air Conditioning
Minimum
Remark if
Sr. No. Name of Equipt./Machinery Technical Specifications Qtty./Nos.
any
Required
1 Wall Chart of Vapour Compression Wall charts of PVC / Acrylic 1
refrigeration system material
2 Wall Chart of Steam jet refrigeration Wall charts of PVC / Acrylic 1
system material
3 Wall Chart of i)Vortex Wall charts of PVC / Acrylic 1Each
tube ii) Pulse material
tube refrigeration,
iii)Solar refrigeration
4 Wall Chart of i) Wall charts of PVC / Acrylic 1Each
heat engine ii) heat material
pump iii)refrigerator.
5 Wall Chart of I)Bell Wall charts of PVC / Acrylic 1
Coleman air refrigerator material
ii)PV Diagram & TS Diagram of
Bell Coleman air refrigerator
6 Wall Chart of Wall charts of PVC / Acrylic 1Each
i) Vapour Compression Cycle material
ii) P-H and T-S diagram of Vapour
Compression Cycle
7 Wall Chart of aqua- ammonia Wall charts of PVC / Acrylic 1
system (simple & practical) material
8 Wall Chart of Li-Br Absorption Wall charts of PVC / Acrylic 1
System material
9 Wall Chart of Electrolux System Wall charts of PVC / Acrylic 1
material
10 Wall Chart of Superheating & under Wall charts of PVC / Acrylic 1
cooling. material

31
 11 Wall Chart of Capillary tube, Wall charts of PVC / Acrylic 1
automatic Expansion material
valve,Thermostatic Expansion valve

12 Wall Chart of Psychrometric chart Wall charts of PVC / Acrylic 1

material
13 Wall Chart of Wall charts of PVC / Acrylic 1Each
i)Window Air Conditioner material
ii)Package Type Air Conditioner
iii)Split Type Air Conditioner
iv)Year round Air Conditioner
14 Wall Chart of Charging Unit. Wall charts of PVC / Acrylic 1
material
15 Wall Chart of Wall charts of PVC / Acrylic 1Each
i)Duct System material
ii) Diffussers
iii) Grills
iv)fans and blowers

Note: Wall chart size- 3ft x 3 ft

32
 ANNEXURE - II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT & MACHINERY
(Desired Equipment/ Hand Tools) (Optional
Equipmentl)
1. Name of course/ Department:- Mech. Engg. Dept
2.Name of laboratory :- Mechanical Measurement and Control, MQC

Minimum
Remark if
Sr. No. Name of Equipt./Machinery Technical Specifications Qtty./Nos.
any
Required
1 displacement measurement using sensor -+/-10mm LVDT 2
LVDT Display 3.5 digit dogital display
2 Snap Gauges Go , No. Go 10,20,50 mm 2
3 Limit Gauges – 1) Plug gauges and Go , No. Go 10,20,50 mm 2
2) ring guages
4 Thread Gauges Go , No. Go BSW/Metric 2
5 Tool Maker Microscope Magnification minimum 30x, 1
Travel 25mm, Graduated in 0-
360 degree with thread
templates, occulars
6 Angle Dekkor Magnification 10x, measuring 1
range 0-60 minutes in x-y
direction, LC=1 minute
7 Clinometer Reading in degree & minutes, 1
Range 0-360 degree
8 Ultrasonic Thickness Gauge For measuring thickness of 1
different material like
Aluminium, Plastic, Mildsteel
within an accuracy of 0.2 mm
Range 0-30mm

33
 ANNE
XURE - II MSBTE NORMS AND STANDARDS FOR
EQUIPMENT
LIST OF EQUIPMENT &
MACHINERY (Desired
Equipment/ Hand Tools)
(Optional Equipmentl)
1. Name of course/ Department:- Mech. Engg. Dept
2.Name of laboratory :- Fluid Mechanics and Machinery, Fluid Power

Minimum
Remark if
Sr. No. Name of Equipt./Machinery Technical Specifications Qtty./Nos.
any
Required
1 i)Simple and differential manometers i) Simple manometers 50 cm 1
ii)Pitot Tube scale
ii)Differential manometers 50 cm
scale
2 Wall chart of Hydroelectric power Wall charts of PVC / Acrylic 1
plant coated material
3 Wall chart of Wall charts of PVC / Acrylic 1Each
i)Pelton whee coated material
ii) Francis
iii) Kaplan turbine.
4 Wall chart of Centrifugal pumps – Centrifugal pumps closed system 1
single stage, multi stage with variable speed.
5 Wall chart of Wall charts of PVC / Acrylic 1Each
i)submersible pump coated material
ii) jet pump
6 Wall chart of Reciprocating pumps Reciprocating pumps closed 1
system with variable speed.
7 P Simulator Pneumatic and Electro 1
Pneumatic Simulation software
with user manual & Activity
Book.
8 H Simulator Hydraulic and Electro Hydraulic 1
Simulation software with user
manual & Activity Book.

Note: Wall chart size 3ft X 3ft

34
 ANNEXURE - II
MSBTE NORMS AND STANDARDS FOR EQUIPMENT
LIST OF EQUIPMENT &
MACHINERY (Desired
Equipment/ Hand Tools)
(Optional Equipmentl)
1. Name of course/ Department:- Mech. Engg. Dept
2.Name of laboratory :- Automation

Minimum
Remark if
Sr. No. Name of Equipt./Machinery Technical Specifications Qtty./Nos.
any
Required
1 CAD/CAM Softwares Any one of the following- 02 Nos.Minimum
Unigraphics NX4 Pro 10 User Lience.
E Catia

2 CAM Software CNC Offline programming 10 User Licence

Trainer
3 Working Model of Robot 5 axis Robot 1No.

4 Robox Robox Robot simulation

Software ( Robox simulation
Software with User manul &
activity book.)

5 Mechatronics Simulation Software Mechatronics Simulation 1

Software
(Mechatronics Simulation
Software with user manual &
activity book)
6 LSM Controller Package I)LSM Controller +4-Axis,PLC 1
ii)DC Servomotor iii)Optical
incremental encoder iv)
Techogenerator v) PWM 4
Quadrant motor drive vi) power
supply for drive

35