PIN A rR T Located inside the knuckle < LeafiFlap Ball Bearing Fixing Holes Counter sunk for serew fing CR OE eT eke ae eee Eee Eei eg eur tese m ‘A 5mm knuckle hinge has @ flap with three knuckles attached to the frame and flap with two knuckles attached to the CaS Uae Ceo ue Con un atte eee Cee Mes Pane ry Preeti EUROART hinges, where specifed correctly to the recommendation of BS EN 1935, are capable of withstanding a severe degree of use. Most are particularly suitable for use with door closers and will help to ensure the smooth eee mengFf certifire "CERTIFICATE OF APPROVAL - No GF 863 certity tha, In accordance with nts for Cortficetion of Fire Protection Products ‘The undermentioned products of EURO-ART (UK) LTD 4 Chain Caul Way, Rivers Docklands, Preston, Lancashire PR2 2YL. Tol: 0208 453 1017 Fax: 0208 961 2791 Have been assessed against the requirements of the Techmnicel Schedule(s) ‘denoted below and are approvad for use subject to the conditions ‘appendlod horoto: CERTIFIED PRODUCT TECHNICAL SCHEDULE Euro-Art Stainless Steel Ball TS24 The Contribution of Bearing Hinges Single Axis Hinges to the Fire Resistance of Door Assemblies Signed and sealed for and on behalf of CERTIFIRE a Sir Ken Knight Issued: 20 July 2011 Chairman - Management Council —_ Revised: 20 November 2012 Page 1 of 5 Valid to: 19 July 2016 There the propery of Wargo Craton Unie, of Exo (UN) i eid ce: hed nde Metra Main RRP UK RepeinSele MS S08QJ) EUROART Standards and Certification BS EN 1935 Single axis hinges BS EN 1935 classifies door furniture by using an 8 digit coding eystem. A similar classification applies to all building hardware product standards so that complementary items of hardware can be specifi to, for instance, 2 common level of corrosion resistance, category of Use, ote. Each digit reters to. particular feature of the product measured against the standard’s pertormance requirements. Digit -Category of use Four categories of use are identified: ~ grade 1: ight duty + grade 2: meaum aury ~ grade 3: heavy duty - grado 4: sovaro duty Digit 2~ Durability “Three grades are identified for single-axis hinges manufactured to this European standard: + grade 3: 10 000 test cycles, for light duty hinges on windows only + grade 4:25 000 test cycles, for light duly hinges on windows and doors, ~ grade 7: 200 000 teat eysleo, for medium. Heavy and aovere duly hinges on doors only Digit 3-Test door mass Eight door mass grades rotatod to single-axis hinges are identified in this European standard as shown in Table 1 bolow. Tablet Test door mass grade Door mass ° 10 kg 1 20g 2 40 kg 3 60 kg 4 80 kg 5 100g 6 120ka F 160 kg Digit 4 ~ Suitability for fire/smoke door use Two grades of suitability are idenlfied for single-exis hinges: = grade 0: not suitable for freismoke resistant door assembiias - grade 1: suitable for fra/emoke resistant door assemblies subject to satisfactory assessment of the contribution of tho single-axis hinge to the fio resistanco of the specified frelsmoko door assemblies. ‘Such assessment is beyond the scope of this European standard (see EN 1634-1), Digit 5 - Safety Single-axis hinges are required to satisfy the essential requitements of safety in use. Therefore, only grade 1 is identified. Digit 6 ~ Corrosion resistance Five grades of corrosion resistance are identified in accordance with EN 1670: - yrauz 0. no defined conusiun resistance. + grade 1: mild resistance, + grade 2: moderate resistance. + grade 3: high resistance, + grade 4: very high resistance, 114QJ) EUROART Standards and Certification Digit 7 ~ Security ‘Two grades of security are identified for single-axis hinges: = grade 0: not suitable for use on burglar-resistant door assemblies + grade 1: suitable for applications requiring a degree of secutty. Annex C of this European standard details the hinge grade to se for the level of security required, Digit 8 - Hinge grade Fourteen gues are identified in this European signed and ave dead nt Table 2 uel, The fll asian fs showin the standard Table 2 Hinge grade Usage Test cycles Door mass 1 Window 70000 10Kg 2 Window 40.000 20k 3 WindowiDoor 25.000 20kg 4 Door 200 000 20kg 5 window 10 000 a0Kg 6 Window/Door 25.000 40k9 7 Door I 200 000 40kg 8 Window 10.000 60kg os Window | __ 25.000. “cohy 10 oor 200 000 60kg " Door | 200 000 20kg 12 Door 200 000 40049 13 Door 200 000 120g 14 Door 200 000 160% BS EN 1634 Part 1: 2000 Is the Furopean Fite Safely Standard for cetermining the fre resistance of door and shutter assemblies iach for installations within openings incorporated in vertical separating elements (doorsets). Locks can be assessed to be suitable on:- FD30 (20 minute) Fire Doors. F DEO (60 minute) Fire Doors ing hareware designed C Marking CE Marking is the easiest and safest route to providing compliance with the latest UK Construction Products Directive for hardware cod on fro, emoke and oceape doore. 115QJ) EUROART Technical considerations Door weight. door size, location 6 intended use To specify the correct hinge there are a number of factors that eed to be taken into consideration. The majority of situations are straightiorward and present few problems, however it is important ‘that specifiers recognise where special cate is required to ensure Jong and trouble tree operation. Hecause ot the wide vanety of Circumstances tha exist itis impossible to be prescriptive, however ‘the following is intended to draw attention to some of the potential problem areas and explain some of theprinciples involved. Factors to consider when specitying hinges «= Isitatire, smoke oremeraency escape door? ‘+ How heavyisthe door and whataare the door dimensions (height, width and thickness)? ‘¢ What's the door's construction and are there any unusual features, thotoouldatfoottho hingoo? ‘= Where is tha door situated eg. internal or external: Is it near the coastorinaswimming pool? ‘= What level of use/abuse will the door be subject to e.g. office, hhospitalor school corridor? ‘+ What other items of hardware are to be fitted, that ma hinge performance, typically door closers or door stops‘ ++ Any other unusual features involved eg. door has radius top or the doorisa bifold, affect the Forces operating on a door ‘Thora are two main forces that the hingo has to cope with. The ‘vertical load; and, as hinged doors are side-hung, the horizontal or lateralioad. “Tho wortiealioas ica cioetrecult ofthe grose deer weight. Tho horizontal loadis created by: ‘The door weight The door heighttowidth ratio Where thehinges are positioned, ‘The wider the doors in relation toits height, the greater the side load that the hinges and thai ixings have fo support. Locating the hinges {tis usual for at least three hinges to be fitted on doors; their positioning is dotermined by the size, woight and construction of General guidelines “Top and bottom hinges must be as far apart as reasonable, tomaximise their ability to cope with side load. Consider any otner factors that wil increase the loadings of hinges anatmerrings. ‘Adgitional ringes are needed for tal doors, to prevent warping (doors taller than 2200mm should be fitted with four hinges). Fig. 4 Examples of typical hinge positions (Fig. 2) 1 Standard hinge positioning, 2Altemative standard hinge position for improved load carrying ‘and provides additional support for a door closer. 3 For taller andlor heavier doors andlor where @ door requires additional support cue I's level of usa/abuse (eg. school or hospital) 4 For hoavy doors or doors with a incroasod side load (ie. wide doors). 116BJ) EUROART Finishes: SSS, PSS, PVD & AB Features ‘* Double bail bearing, five knuckle hinge ‘© Successfully type tested for conformity to all the requirements of BS EN1935 ‘© Supplied with SS Screws ‘* Load bearing capacity up to 120kg ‘© Available square or radius +» Tested to over 200,000 cycles ‘* Suitable for fire/smoke resistant doors ¢ Finished with softened edges ‘¢ Pre-cut intumescent hinge pads available = ofits CE fs ew 1005, Feertitire Two Ball Bearing SS Grade 13 Hinge wiuee433 ws oho oo : oh° o oS winpe42.s3 ° H © Jo Ho oho ofoO ie eHo ,| |e ° ° ° oRO HINBB4.543.4 a ge Sq (TTT) Seq of SS 0° % Lo 2990 117BJ) EUROART Feentitre Finish: SSS, PSS, PVD, AB S Ww We cc Grade 13 Security/Hospital Tip Hinge Features ‘* Double ball bearing, five knuckle hinge ‘¢ Successfully type tested for conformity to all the requirements of BS EN1935 ‘¢ Load bearing capacity up to 120kg Tested to over 200,000 cycles ‘* Suitable for fire/smoke resistant doors @ Prevents removal of door leaf if hinge knuckle ie attacked ¢ Predominately used on perimeter doors where the hinge knuckle is located externally Ret No Sis BHISé 10276 x3mm BHt68 10289 x 3mm fe BHI4 102x 102 3mm Features ¢ Hospital tip hinge + Sloped tip provents hanging any objects on the tip of the hinge, making it difficult to attach rope, wearing apparel etc. ‘© Double ball bearing, five knuckle hinge « Load bearing capacity up to 120k9 + Tested to over 200,000 cycles Ret No size fe HTH433, 10276 x 3mm fe HTHES 59 10289 x 3mm eo HTH, 102x 102 3mm 118BJ) EUROART Finish: SSS, PSS, PVD, AB Finish: 55% 5) PSS, PVD, AB =. 7 ‘Two Ball Bearing SS Hinges Features ¢ Double ball bearing, five knuckle hinge # Successfully type tested for conformity to all the requirements of 8S EN1935 + Load bearing capacity up to 120k9 # Tested to over 200,000 cycles ‘¢ Suitable for fire/smoke resistant doors RefNo, size Hinges93 127x76 «3mm fe Hinges3s3 | 127 893mm © Hineess 150K 102 3mm fe HINBEs«35 —: 127%102x8.6rm fe Hinseecs sa x102 vam HINGES 54.54: 188 x114 x4mm fe HinsBacd 208 x102.x4mm Features Double ball bearing, five knuckle hinge Load bearing capacity up to 120kg # Tested to over 200,000 cycles Ret. No. Sizo BBHI7! 10276 x 3mm @ BBHi8t 102.89 x 3mm peri91 12x 102% Sn 119Finish: SSS, PSS, PVD, AB SS, PSS, PYD, AB Standard Weight, Three Knuckle Hinges. Features ‘¢ Standard weight, fixed pin, three knuckle inges # Security dog bolt version ‘¢ Predominately used on perimeter doors wihere the hinge knuckle is located externally ‘© Maintenance free, guaranteed for 25 years ¢ Successfully type tested for conformity to all the requirements of 8S EN1935 Grade13 Load bearing capacity up to 120kg @ Tested to over 200,000 cycles = Shitahle for fire/emoke resistant dears RefNo. Size | HLMAOUSEC 102x80%3mm fe Mindo2sEC 102. 10233mm Features @ Standard weight, fixed pin, three kaweklee hinges ‘¢ Maintenance free, guaranteed for 25 years # Successfully type tested for conformity to all the requirements of 8S EN1935 Grade13 ‘¢ Load bearing capacity up to 120kg Tested to over 200,000 cycles ‘© Suitable for fire/smoke resistant doors Ret. No. Size fe HuHaor © 10289x3mm fe HLHd02: 102 102x3mm 120Zs) EUROCART Heavy Weight, Three Knuckle/Lift-off Hinges Features Heavy weight, fixed pin, three knuckle hinges ‘¢ Maintenance free, guaranteed for 25 years Successfully type tested for conformity to all the requirements of BS EN1935 Grade14 ‘¢ Load bearing capacity up to 160kg @ Tested to over 200,000 cycles ‘¢ Suitable for fire/smoke resistant doors ‘¢ Supplied with Mex31mm wood screws Ret. No. size fe HuHs01 127 «102x35men fe HLHS02 127x127 x3.5mem Finish: SSS, PSS, PVD, AB Features Standard weight, lift-off, two knuckle hinges Maintenance free, guarenteed for 25 years ‘¢ Successfully type tested for conformity to all the requirements of BS EN1935 Grade 1 ¢ Load bearing capacity up to 80kg Tested to over 200,000 cycles ‘¢ Suitable for fire/smoke resistant doors ¢ Supplied with MSx31mm wood screws Ret. No. Size © Lowsor 102.89 «3mm © LoH602 102 102x3mm Finis! 1: 555, PSS, PVD, AB ce 121BJ) EUROART Parliament Hinge Finishes: SSS, PSS, PVD & AB Rising & Falling Hinge ©9900 6 IO fe) 19 Finishes: SSS, PSS, PVD & AB Rebated Door Hinge Fie 0 File Hinges RetNo Size(AxBxC) fe HINPAGS 5 100 x 100 x3.5mm fe Hinpads 125 100% 3.5mm fe HINPAdS 150 x 1002 3.5mm Ret No Sizo fe HINRR433 : 102 « 76 x 3mm - Right hand rsing fe HINRL433 102 x76 x 3mm - Left rend rising fe HINFR433 » 102 x 76 x 3mm - Right hand fang fe HINELAg | 10276 amm_ Loftnand fling et. No. ‘sae fe HiNRBBASES 102% 68 x amm 122=) EUROART Hinges Double Ball Bearing Hinge Ret No. Siee fe Hngesze 76x61 20m fs hinaases2 — 75260.42nm Svingease 782 76x2rm Hnges225 —7635%e2.Smm # titvgea2 #25 7626312.5em @ rnseas25 | 753276e25rm Finishes: SN, PB, CP, AB, SC Double Action Spring Hinge 1=0 | . weno. Sao as wapacty eo fe hnDKs = 100nm 2209 A @ HINDAS 125mm 2g ° S HRDAS 150mm 404g a Stina? 175mm sg @ HINOAS 200mm 9 5 q ° ° au gle Action Spring Hinge Ret No. Sao aa wapaty e HINSAS 100mm 15k S HNSAS 125mm 25g @ HINSAG 150mm 359 SHNSAT 75mm 15g SRA 00mm 559 hes: SSS, PSS, PVD & AB inane 123QJ) EUROART ish: PB, CP, SC, SN, AB Features Concealed Hinges = Zamak alloy body, hardened steel pins « totally invisible when door is closed ‘¢ Non-handed ‘¢ Suitable for timber and metal doors = _.— Product Size Min door Weight rr € 1 4 FE Code Thickness Thickness Rated — Dzmmovom Hoe es Cook Doon boat OMG 19x45nm 19mm Wigs 320mm ——1240mm —4Smm ~~~ 7Omm —~18.20mm 16.20 BHIGE0 _19x600m 19mm “kes 820mm ——1270mm ——_—6Omm ——_— 620mm —_47.80mm —_26.00nm BHIEIO —_16xTONm 22mm 25igs 400mm ———15.70mm 70mm ——7.000m 280mm —_39.30mm BHIseS _19x95nm 26mm 369s 460mm 80mm Sm 8.3mm 200mm 40.80 DHONI —2Sxtt7mm 95mm igs GAdmm ——2470mm 117mm 11.000 —2660mm —_62.70nm SiGe? a8 I17mm tim eskge 640mm ——~87.HGmm 7mm —[email protected] ——_-*1.0Omm 60mm BHISIG9 SGI 7mm Togs 750mm 860mm 430m 1.100 48.29 73.30 124