TD157

INSTRUCTIONS
WIRELESS RESTAURANT
GUEST PAGING SYSTEM

Henan Eshow Electronic Commerce Co., Ltd

EU Importer：
Add: 7/F, Sanjiang Building, No.170 Nanyang Road, Huiji District, Name：Germany Retevis Technology GmbH
Zhengzhou, Henan, China
Address：Uetzenacker 29,38176 wendeburg
Facebook：facebook.com/RetekessWirelessSystem
E-mail: [email protected] MADE IN CHINA
Web: www.retekess.com
 Note: If there is no special requirement, please do not modify the host Replacement of any transmitter component (crystal, semiconductor, not comply with RF exposure requirements and should be avoided.
EN: base number. Otherwise, all extensions need to be reset to use the etc.) not authorized by the local government radio management • DO NOT operate the transmitter in areas that are sensitive to
PRODUCT LIST number.Do not set the base number to “000”. depa-rtments equipment authorization for this radio could violate the electromagnetic radiation such as hospitals, aircraft, and blasting
rules. sites.
3. 【F2】Extension ID number setting Avoid Choking Hazard
3.1. First remove all extensions from the base, then enter the setup FCC Requirements: Small Parts. Not for children under 3 years.
mode, and the default screen flashes "01". After the extension to be • This device complies with part 15 of the FCC Rules. Operation is
set is inserted into the charging slot, the function light flashes. subject to the following two conditions:
Then input the new ID number “1-998”by the keyboard within (1) This device may not cause harmful interference, and
3 seconds, and press the [Call] button to save. At this time the (2) this device must accept any interference received, including Protect your hearing
extension prompts the flash to be set successfully. After removing the interference that may cause undesired operation • Use the lowest volume necessary to do your job.
extension, set the next one in turn, and then press [Clear] to exit after • This equipment has been tested and found to comply with the limits • Turn up the volume only if you are in noisy surroundings.
all extension settings are completed. for a Class B digital device, pursuant to Part 15 of the FCC Rules. • Turn down the volume before adding headset or earpiece.
RECEIVER *16 3.2. Do not set "99/999" as the extension number. This number is the These limits are designed to provide reasonable protection against • Limit the amount of time you use headsets or earpieces
WARNING
shutdown command. harmful interference in a residential installation. at high volume.
3.3. To modify the extension number, simply overwrite the old number This equipment generates uses and can radiate radio frequency energy • When using the radio without a headset or earpiece, do
with the new one. and, if not installed and used in accordance with the instructions, may not place the radio's speaker directly against your ear
4. 【F3】Beep switch setting cause harmful interference to radio communications. However, there is • Use careful with the earphone maybe possible
Enter the setting mode, the default screen flashes “01”. At this time, no guarantee that interference will not occur in a particular installation. excessive sound pressure from earphones and
after inputting “0 (off)/1 (on)” from the keyboard, press the [Call] button If this equipment does cause harmful interference to radio or television headphones can cause hearing loss
to save. reception, which can be determined by turning the equipment off and Note: Exposure to loud noises from any source for exten-
POWER *1 5. [F4] prompt duration setting on, the user is encouraged to try to correct the interference by one or ded periods of time may temporarily or permanently affect
TRANSMITTER *1
Enter the setting mode, the default screen flashes “01”. At this time, more of the following measures: your hearing. The louder the radio's volume, the less time
after inputting “1-99” seconds from the keyboard, press the [Call] - Reorient or relocate the receiving antenna. is required before your hearing could be affected. Hearing
BASIC PARAMETERS button to save. - Increase the separation between the equipment and receiver. damage from loud noise is sometimes undetectable at
- Connect the equipment into an outlet on a circuit different from that to first and can have a cumulative effect.
TRANSMITTER
RF ENERGY EXPOSURE AND PRODUCT SAFETY GUIDE which the receiver is connected. Avoid Burns
Dimension 238*151*30mm - Consult the dealer or an experienced radio/TV technician for help. Antennas
Material ABS Before using this radio, read this guide which cont- • Do not use any portable radio that has a damaged
ains important operating instructions for safe usage CE Requirements: antenna. If a damaged antenna comes into contact with
Transmit Power 240mW
and RF energy awareness and control for compliance • (Simple EU declaration of conformity) Henan Eshow Electronic the skin when the radio is in use, a minor burn can result.
Frequency 433MHz with applicable standards and regulations. Commerce Co.,Ltd declares that the radio equipment type is in WARNING Batteries (If appropriate)
Power Supply DC12V/1A compliance with the essential requirements and other relevant • When the conductive material such as jewelry, keys or
Launch Distance ＞800M (in Open Area) provisions of RED Directive 2014/53/EU and the ROHS Directive chains touch exposed terminals of the batteries, may
This radio uses electromagnetic energy in the radio frequency (RF) 2011/65/EU and the WEEE Directive 2012/19/EU; the full text of the complete an electrical circuit (short circuit the battery)
Support Receiver 998(16/SET) spectrum to provide communications between two or more users over EU declaration of conformity is available at the following internet and become hot to cause bodily injury such as burns.
IP Grade IP32 a distance. RF energy, which when used improperly, can cause address: www.retekess.com. Exercise care in handling any battery, particularly when
biological damage. • Disposal placing it inside a pocket, purse or other container with
All Retekess radios are designed, manufactured, and tested to ensure The crossed-out wheeled-bin symbol on your product, litera- metal objects
RECEIVER they meet government-established RF exposure levels. In addition, ture, or packaging reminds you that in the European Union, Long transmission
Dimension 106*51*11mm manufacturers also recommend specific operating instructions to users all electrical and electronic products, batteries, and accumu- • When the transceiver is used for long transmissions,
of the radios. These instructions are important because they inform lators (rechargeable batteries) must be taken to designated the radiator and chassis will become hot.
Material ABS users about RF energy exposure and provide simple procedures on collection locations at the end of their working life. Do not Safety Operation
Receiving Sensitivity -114dB how to control it. dispose of these products as unsorted municipal waste. Dispose of Forbid
LI-Polymer 3.7V/150mAh Please refer to the following websites for more information on what RF them according to the laws in your area. • Do not use charger outdoors or in moist environments,
energy exposure is and how to control your exposure to assure use only in dry locations/conditions.
Frequency 433MHz
compliance with established RF exposure limits: http://www.who.int/en/ IC Requirements: • Do not disassemble the charger, that may result in risk
Standby Time ≈20 Hour Licence-exempt radio apparatus WARNING of electrical shock or fire.
Support Receiver Beep Flashing Local Government Regulations This device contains licence-exempt transmitter(s)/receiver(s) that • Do not operate the charger if it has been broken or
IP Grade IP32 When radios are used as a consequence of employment, the Local comply with Innovation, Science and Economic Development Canada’s damaged in any way.
Government Regulations requires users to be fully aware of and able licence-exempt RSS(s). Operation is subject to the following two • Do not place a portable radio in the area over an air bag
to control their exposure to meet occupational requirements. Exposure conditions: or in the air bag deployment area. The radio may be
awareness can be facilitated by the use of a product label directing (1) This device may not cause interference. propelled with great force and cause serious injury to
INSTRUCTIONS users to specific user awareness information. Your Retekess radio has (2) This device must accept any interference, including interference occupants of the vehicle when the air bag inflates.
1. Notes a RF Exposure Product Label. Also, your Retekess user manual, or that may cause undesired operation of the device. To reduce risk
1.1. All the extension pagers should be placed in the main unit separate safety booklet includes information and operating instructions Le présent appareil est conforme aux CNR d’Industrie Canada • Pull by the plug rather than the cord when disconnecting
charging slot before the operation, and be set up after charging required to control your RF exposure and to satisfy compliance applicables aux appareils radio exempts de licence. L’exploitation est the charger.
for 20 minutes. requirements. autorisée aux deux conditions suivantes : • Unplug the charger from the AC outlet before attempting
1.2. Power on: Place all extensions in the main unit's charging slot. (1) l’appareil ne doit pas produire de brouillage; any maintenance or cleaning.
After the main unit is powered on, the extension will automatically Radio License (if appropriate) (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique • Contact Retekess for assistance regarding repairs and
turn on. Governments keep the radios in classification, business radios operate subi, même si le brouillage est susceptible d’en compromettre le service.
1.3. Power off: Place all extensions in the main unit's charging slot. on radio frequencies that are regulated by the local radio management fonctionnement. • The adapter shall be installed near the equipment and
Input “99/999” by the base keyboard and then press the [Call] button. departments (FCC, ISED, OFCOM, ANFR, BFTK, Bundesnetzagentur shall be easily accessible
1.4. Enter the setup mode: Press the [Call] button and the [Clear] ...).To transmit on these frequencies, you are required to have a license RF Exposure Information • Risk of explosion if battery is replaced by an incorrect
button at the same time until the host screen displays [F1], then enter issued by them. The detailed classification and the use of your radios, • DO NOT operate the radio without a proper antenna attached, as this type. Dispose of used batteries according to the
the mode selection interface. At this time, input the corresponding please contact the local government radio management departments. may damage the radio and may also cause you to exceed RF expos- instructions.
number “1-4”by the keyboard to choose the mode, and press the [Call] Use of this radio outside the country where it was intended to be ure limits. A proper antenna is the antenna supplied with this radio by • Adapter shall be installed near the equipment and shall
key to enter the setting mode. After setting, press [Clear] to exit the distributed is subject to government regulations and may be prohibited. the manufacturer or an antenna specifically authorized by the manuf- be easily accessible.
setting mode, and the standby screen will display “--”. acturer for use with this radio, and the antenna gain shall not exceed • The plug considered as disconnect device of adapter.
1.4.1. Enter the number "1": [F1] Host ID number setting Unauthorized modification and adjustment the specified gain by the manufacturer declared. • The operating temperature of the EUT can’t exceed the
1.4.2. Enter the number "2": [F2] Extension ID number setting Changes or modifications not expressly approved by the party respon- • DO NOT transmit for more than 50% of total radio use time, more specified range.
1.4.3. Enter the number "3": [F3] buzzer switch setting sible for compliance may void the user’s authority granted by the local than 50% of the time can cause RF exposure compliance requirements
1.4.4. Enter the number "4": [F4] prompt duration setting government radio management departments to operate this radio and to be exceeded. Approved Accessories
1.5. Operation process: First set [F1] host ID number setting, followed should not be made. To comply with the corresponding requirements, • During transmissions, your radio generates RF energy that can • This radio meets the RF exposure guidelines when used
by [F3] buzzer switch setting and [F4] prompt duration setting. transmitter adjustments should be made only by or under the supervi- possibly cause interference with other devices or systems. To avoid with the Retekess accessories supplied or designated
After completing the above operations, finally set the [F2] extension ID sion of a person certified as technically qualified to perform transmitter such interference, turn off the radio in areas where signs are posted for the product. Use of other accessories may not ensure
number. maintenance and repairs in the private land mobile and fixed services to do so. compliance with the RF exposure guidelines and may
2. 【F1】Host ID number setting as certified by an organization representative of the user of those • The device complies with RF specifications when the device used at WARNING violate regulations.
Enter the setting mode, the default screen flashes the current host ID services. 5mm from your body. Third-party belt-clips, holsters, and similar acc- • For a list of Retekess-approved accessories for your
number.At this time, after entering the new number “001-999” by the . essories used by this device should not contain any metallic compon- radio model, visit the following website:
host keyboard,press the [Call] button to save. ents. Body-worn accessories that do not meet these requirements may http://www.Retekess.com
1 2