SUPERMICR

Contact Info: www.supermicro.com (Email: [email protected])

R

X9DRL-3F/X9DRL-iF Quick Reference Guide

Manuals: http://www.supermicro.com/support/manuals Drivers & Utilities: ftp://ftp.supermicro.com Safety: http://www.supermicro.com/about/policies/safety_information.cfm
(MNL#1298-QRG)

Motherboard Layout and Features Jumpers, Connectors and LED Indicators Memory Support
Jumpers
10 19 18 KB/MOUSE USB6/7 11 This motherboard supports up to 256 GB of Registered (RDIMM)/Load Reduced
Jumper Item # Description Default
BMC Firmware LED1
UID JUIDB1 VGA 13 COM1 (LRDIMM) ECC or up to 64 GB of Unbuffered (UDIMM) ECC/Non-ECC DDR3
15 17 16 JBT1 26 Clear CMOS See Chpt. 2 in User Manual 800/1066/1333/1600 MHz 4-channel memory in 8 DIMM slots.
LEDM1

FAN5
12
1 FAN6
BMC CTRL JPL2 111 15 14 12 JI2C1/JI2C2 43, 42 SMB to PCI-E Slots Off (Disabled)
Note: For memory optimization, use only DIMM modules that have been validated by Supermicro.

JPB1
114 JPL1 USB8/9
COM2

16 LAN2 LAN1
1
13
1
LAN CTRL LAN CTRL
IPMI_LAN
JPB1 14 BMC Enabled Pins 1-2 (Enabled) For the latest memory updates, please refer to our website at http://www.supermicro.com/

P2-DIMMH1

P2-DIMMG1
JPG1 18 VGA Enabled Pins 1-2 (Enabled) products/motherboard.
PCH SLOT1 PCI-E 2.0 X1

JPL1/JPL2 13, 12 GLAN1/GLAN2 Enable Pins 1-2 (Enabled)

JTPM1

17
1 18
1
JWD1 31 Watch Dog Timer Enable Pins 1-2 (Reset)
DIMM Installation
JPG1

CPU1 SLOT5 PCI-E 3.0 X8

CPU1 SLOT4 PCI-E 3.0 X8
PCH SLOT3 PCI-E 2.0 X4 (IN X8)

CPU1 SLOT6 PCI-E 3.0 X8)

SLOT2 PCI 33MHZ

19
1
USB4

Insert the desired number of DIMMs into the memory slots, starting with P1-DIMMA1.
CPLD ah Connectors
For memory to work properly, follow the tables below for memory population order.
Connector Item # Description
USB5

P1-DIMMC1 CPU2 Refer to the motherboard layout (at left) for the location of the DIMM slots.
P1-DIMMD1

P1-DIMMA1
P1-DIMMB1
COM1/COM2 1, 16 Back Panel COM Port1 / Front Accessible COM2 Header
USB2/3

120
BIOS Fan 1~3 47, 46, 45 CPU/System Fan Headers
J9

Fan 4-6 44, 2, 11 CPU/System Fan Headers

USB0/1

121 Processors and their Corresponding

S-SAS7
X9DRL-iF FanA, FanB 41, 40 CPU/System Fan Headers
Memory Modules
Rev. 1.01
S-SAS6 CPU# Corresponding DIMM Modules
122 JD1 36 Speaker/Power LED Indicator
S-SAS5 CPU1 P1- P1- P1- P1-
S-SAS4
JF1 35 Front Panel Control Header DIMMA1 DIMMB1 DIMMC1 DIMMD1

S-SGPIO1 1 JIPMB1 38 4-pin External BMC I2C Header (for an IPMI Card) CPU2 P2- P2- P2- P2-
P2-DIMMF1
P2-DIMME1

S-SGPIO2 24
BUZZER DIMME1 DIMMF1 DIMMG1 DIMMH1
13
2
JL1 29 Chassis Intrusion
SAS/SATA3 T Intel PCH

SAS/SATA2
A JPW4 JOH1 32 Overheat LED Indicator
125 Processor and Memory Module Population
SAS/SATA1
V
CPU1
JPI2C1 48 Power Supply SMBbus I2C Header
a Number of CPU and Memory Population Configuration Table
SAS/SATA0
JPW1/2 49, 50 12V 8-Pin Power Connectors
JBT1

CPUs+DIMMs (*For memory to work properly, please install DIMMs in pairs)

I-SATA5 16
2
151

I-SATA4
JPW4 51 24-Pin ATX Main Power Connector 1 CPU & CPU1
127 2 DIMMs P1-DIMMA1/P1-DIMMB1
I-SATA3 JSD1 30 SATA DOM (Device on Module) Power Connector
JPW2 1 CPU & CPU1
I-SATA2 T-SGPIO2 1
131
34
Battery
JSTBY1 37 +5V Standby Power Header 4 DIMMs P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1
I-SATA1 128 150
JWD1 JOH1

137 FAN2 JTPM1 17 TPM (Trusted Platform Module)/Port 80 2 CPUs & CPU1 + CPU2
19
2 12 413
4 2 DIMMs P1-DIMMA1, P2-DIMME1
FAN1

12
3 JSTBY1
T-SGPIO1 147
16 FAN4 FAN3
FANB FANA
JUIDB1 9 UID (Unit Identification) Switch
JL1

3
JSD1

JIPMB1

JI2C2
JI2C1

13
3

JPW1
JD1 146
LED2

130 128 2 CPUs & CPU1 + CPU2

JPI2C1

JF1
I-SATA0
15 138 139 10
4 11
4 14
4 145
148
LAN1/LAN2 6, 7 G-bit Ethernet Ports 1/2 4 DIMMs P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1
3 149
(IPMI) LAN 4 IPMI Dedicated LAN 2 CPUs & CPU1 + CPU2
6 DIMMs P1-DIMMA1/P1-DIMMB1/P1-DIMMC1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1
(I-)SATA0~1 28 Intel PCH SATA Connectors 0/1
= mounting hole Note: Item numbers are listed in counterclockwise order. 2 CPUs & CPU1 + CPU2
(I-)SATA2~5 27 Intel PCH SATA Connectors 2~5 8 DIMMs P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-
DIMMG1/P2-DIMMH1
CPU Installation Heatsink Installation Front Panel Control (JF1) (S-)SATA0~3 25 SATA Connectors 0~3 (X9DRL-iF)
(S-)SAS0~7 22 SAS Connections 0~7 (for X9DRL-3F only)
CPU Keys Screw #4 20 19 (S-)SGPIO1/2 24, 23 Serial (SAS) General Purpose I/O Headers 1/2
Ground NMI
Screw #2 (T-)SGPIO1/2 33, 34 Serial (SATA) General Purpose I/O Headers 1/2
Screw #1
X X
USB 0/1, 2/3 21, 20 Front Panel USB Connections 0/1, 2/3 Back Panel IO Connectors
FP PWRLED 3.3 V Stby USB 4 19 FP-Accessible Type A USB Connections 4
Socket Keys
HDD LED 3.3V Stby USB 6/7, 8/9 3, 5 Backpanel USB Connections 6/7, 8/9 IPMI LAN

Screw #3
NIC1 Link LED 3.3V Stby VGA 8 Backpanel VGA Port
USB 3
NIC2 Link LED 3.3V Stby
1.
Blue+ (OH/Fan Fail/
Red+ (Blue LED Cathode)
LED Indicators
2. PWR FaiL/UID LED)
Power Fail LED
LED Item # Description Color/State Status
3.3V Stby
OP
EN
1st

LED1 10 Rear UID LED Blue: On Unit Identified

Motherboard Ground Reset Reset Button COM1 USB 1 USB 2 GLAN1 GLAN2 VGA UID
OPE
N 1s
t
LED2 39 Onboard PWR LED Green: On Power On USB 0
Ground PWR Power Button
Mounting Hole LEDM1 15 BMC Heartbeat LED Green BMC Normal
2 1

Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as drawings shown in this guide. Note: Refer to Chapter 2 of the User Manual for detailed information on jumpers, connectors, and LED indicators. Note: Refer to Chapter 2 of the User Manual for detailed information on memory support and CPU/
motherboard installation instructions.