ENERGY SECTOR

POWER ELECTRONIC
CAPACITORS
DC LINK CAPACITORS & SNUBBER CAPACITORS -
RELEVANT FOR WIND PLANTS, SOLAR POWER PLANTS,
MEDICAL AND INDUSTRIAL EQUIPMENT, CAR ELECTRONICS

AC/DC GENERAL PURPOSE CAPACITORS -

RELEVANT FOR POWER ELECTRONIC APPLICATIONS WITH
HIGH CURRENT AND HARMONICS DISTORTION WITH
LONG LIFE EXPECTANCY
 CAPACITOR SELECTION GUIDE

ISKRA MANUFACTURES AND SUPPLIES A WIDE RANGE OF POWER ELECTRONIC CAPACITORS WHICH CAN BE USED FOR
VARIOUS FUNCTIONS IN ELECTRIC CIRCUITS. THEY ARE MOST COMMONLY USED IN FREQUENCY OR VOLTAGE INVERTERS,
UNINTERRUPTIBLE POWER SUPPLIES, MOTOR DRIVES, WELDING EQUIPMENT, WIND AND SOLAR POWER SYSTEMS.

A TYPICAL SWITCHING-MODE POWER SUPPLY IS SHOWN IN THE FIGURE BELOW. DC LINK CAPACITORS AT POSITION C1
ARE USED FOR DC VOLTAGE SMOOTHING. CAPACITORS AT POSITION C2 ARE SNUBBER CAPACITORS. WHEN A SWITCH
OPENS, THEY ELIMINATE VOLTAGE SPIKES CAUSED BY CIRCUIT INDUCTANCE. AC FILTERING CAPACITORS AT POSITION C3
ARE USED IN INPUT/OUTPUT LOW-PASS LC FILTERS.

THE AC/DC GENERAL PURPOSE CAPACITORS MAY BE USED IN AC OR DC APPLICATIONS.

BLOCK DIAGRAM

AC/DC DC/AC

C3 C2 C1 C2 C3

TABLE OF CONTENTS

TYPE
PLACE FUNCTION MOUNTING PAGE
DESIGNATION

KNG2047
KNG2048 WITH SCREWS 5
DC LINK KNG3047
ENERGY STORAGE KNG3048
C1 BYPASS
KNG4910
DECOUPLING
KNG4914
SMOOTHING FOR PCB 8
KNG1910
KNG1914
DC link EV WITH LUGS 25

KNO19Ax
WITH LUGS 27
SNUBBERING KNO19Bx
C2
RESONANT KNO1910
FOR PCB 27
KNO1914
KNI5048 WITH SCREWS 34
C3 AC FILTERING
KNB1910
FOR PCB 42
KNB1914

3
 TERMS AND DEFINITIONS

CN – RATED CAPACITANCE Rs – SERIES RESISTANCE

NOMINAL VALUE OF CAPACITANCE MEASURED AT 20 °C. EFFECTIVE OHMIC RESISTANCE OF THE CONDUCTOR OF A
CAPACITOR UNDER SPECIFIED OPERATING CONDITIONS.
UNDC – RATED DC VOLTAGE
ESR – EQUIVALENT SERIES RESISTANCE OF A
MAXIMUM OPERATING PEAK VOLTAGE OF EITHER CAPACITOR
POLARITY BUT OF A NON-REVERSING TYPE WAVEFORM
FOR WHICH THE CAPACITOR HAS BEEN DESIGNED. EFFECTIVE RESISTANCE WHICH, IF CONNECTED IN SERIES
WITH AN IDEAL CAPACITOR OF CAPACITANCE VALUE
Urms – RATED RMS VOLTAGE EQUAL TO THAT OF THE CAPACITOR IN QUESTION,
ROOT MEAN SQUARE OF MAX. PERMISSIBLE VALUE OF WOULD HAVE A POWER LOSS EQUAL TO ACTIVE POWER
SINUSOIDAL AC VOLTAGE IN CONTINUOUS OPERATION. DISSIPATED IN THAT CAPACITOR UNDER SPECIFIED
OPERATING CONDITIONS.
UN – RATED AC VOLTAGE ESR = tan(δ0) / (ω x C) + Rs
MAXIMUM OPERATING PEAK RECURRENT VOLTAGE OF
EITHER POLARITY OF A REVERSING TYPE WAVEFORM FOR Pdiss– DISSIPATED POWER
WHICH THE CAPACITOR HAS BEEN DESIGNED. ACTIVE POWER DISSIPATED IN THE CAPACITOR.

Ur – RIPPLE VOLTAGE Pdiss = I2rms x ESR

PEAK-TO-PEAK ALTERNATING COMPONENT OF THE Ls– SELF-INDUCTANCE

UNIDIRECTIONAL VOLTAGE. THE SUM OF ALL INDUCTIVE ELEMENTS WHICH ARE
CONTAINED IN A CAPACITOR.
θamb– AMBIENT TEMPERATURE
Imax – Maximum current
TEMPERATURE MEASURED FROM THE DISTANCE OF
MAXIMUM RMS CURRENT FOR CONTINUOUS OPERATION.
APPROXIMATELY 0.1 m AND AT TWO-THIRDS OF THE
HEIGHT OF THE CAPACITOR.

(dU/dt)max – MAXIMUM RATE OF VOLTAGE RISE θmin – LOWEST OPERATING TEMPERATURE

MAXIMUM PERMISSIBLE REPETITIVE RATE OF VOLTAGE LOWEST TEMPERATURE OF THE DIELECTRIC AT WHICH
RISE OF THE OPERATIONAL VOLTAGE. THE CAPACITOR MAY BE ENERGIZED.

θmax – MAXIMUM OPERATING TEMPERATURE

Î – MAXIMUM PEAK CURRENT
HIGHEST TEMPERATURE OF THE CASE AT WHICH THE
MAXIMUM REPETITIVE PEAK CURRENT THAT CAN OCCUR
CAPACITOR MAY BE OPERATED.
DURING CONTINUOUS OPERATION.
Î = C x (dU/dt)max
Δθcase – CONTAINER TEMPERATURE RISE
DIFFERENCE BETWEEN THE TEMPERATURE OF THE
HOTTEST POINT OF THE CONTAINER AND THE
ÎS – MAXIMUM SURGE CURRENT
TEMPERATURE OF THE COOLING AIR.
PEAK NON-REPETITIVE CURRENT INDUCED BY SWITCHING
Rth – THERMAL RESISTANCE
OR ANY OTHER DISTURBANCE OF THE SYSTEM WHICH IS
ALLOWED FOR A LIMITED NUMBER OF TIMES, FOR THERMAL RESISTANCE INDICATES HOW MANY DEGREES
DURATIONS SHORTER THAN THE BASIC PERIOD. THE TEMPERATURE OF THE CAPACITOR RISES AT THE HOT
SPOT IN RELATION TO THE DISSIPATION LOSSES.
Îs = C x (dU/dt)s

θhs – HOT-SPOT TEMPERATURE

tan(δ) – TANGENT OF THE LOSS ANGLE OF A CAPACITOR TEMPERATURE AT THE HOTTEST SPOT INSIDE THE
RATIO BETWEEN EQUIVALENT SERIES RESISTANCE AND CAPACITOR.
THE CAPACITIVE REACTANCE OF A CAPACITOR AT A θhs = θamb + Pdiss x Rth
SPECIFIED SINUSOIDAL ALTERNATING VOLTAGE,
FREQUENCY AND TEMPERATURE. Pmax – MAXIMUM POWER LOSS

tan(δ)= ESR x ω x C = tan(δ0) + Rs x ω x C MAXIMUM PERMISSIBLE POWER DISSIPATION FOR

CONTINUOUS OPERATION.
tan(δ0)= DIELECTRIC LOSS FACTOR
Pmax = (θhs - θamb ) / Rth

4
 DC LINK CAPACITORS
TYPE KNG2047 - KNG3047, KNG2048 - KNG3048

APPLICATIONS
HYBRID VEHICLES
WIND PLANTS
ELECTRIC ENERGY GENERATION FROM SEA WAVES
MEDICAL EQUIPMENT
INDUSTRIAL EQUIPMENT
CAR ELECTRONICS
RAILWAYS AND TURBINES (GENERATOR)
FREQUENCY INVERTERS
ELEVATORS
WELDERS

REFERENCE STANDARDS FEATURES

IEC 61071 USED IN DC-LINK CIRCUITS, CAN REPLACE

ELECTROLYTIC CAPACITOR
UL 810 (CONSTRUCTION ONLY) FILE No.: E196169
LOW ESR, HIGH RIPPLE CURRENT HANDLING
CAPABILITIES
LOW ESL
SELF-HEALING PROPERTIES
LONG LIFETIME

SPECIFICATIONS ALUMINIUM CASE,

FILLED WITH EPOXY RESIN

CAPACITANCE RANGE SEE TABLE

CAPACITANCE TOLERANCE ± 10 %, ON REQUEST ± 5 %

VOLTAGE RANGE MAX. 2200 V DC

DISSIPATION FACTOR TAN(Δ0) < 2 x 10-4/1kHz

SERIES RESISTANCE < 3 mW / 1 kHz

DIELECTRIC SELF-HEALING MPP, ALUMINIUM CASE, WITHOUT OVERPRESSURE DEVICE

TEMPERATURE COEFFICIENT -2.3 % FROM -20 ° TO +70 °C

OPERATING TEMPERATURE -40 °C TO 85 °C (HOT SPOT)

INDUCTANCE < 70 nH

TEST VOLTAGE TERMINAL TO TERMINAL = 1.5 UNDC, 10 s ; TERMINAL TO CASE 3.6 kV AC , 2 s

CASING MATERIAL ALUMINIUM

CAP UL 94 V-0
FILLING EPOXY RESIN DRY, UL 94 V-0

TERMINALS M6x10 INTERNAL THREADS ; M8 SCREW

TORQUE OF TERMINALS M6: 5 Nm ; M8: 6 Nm

BASE STUD M12 x 16, TORQUE 10 Nm

MAX. ALTITUDE 4000 m

MAX. HOT SPOT TEMPERATURE 85 °C

CLIMATIC CATEGORY 40/85/21 ACCORDING TO IEC 68/1
LIFETIME EXPECTANCY 100 000 HOURS AT UNDC , θhs = 70 °C

5
 DC LINK CAPACITORS
TYPE KNG2047 - KNG3047, KNG2048 - KNG3048

GENERAL CHARACTERISTICS

CAPACITANCE RANGE
UNDC (V DC) CN (µF) Imax (A) Î (kA) Îs (kA) Rs (mW) Ls (nH) Rth (K/W) D x H (mm) P (mm)

600 30 3.3 9.9 1.4 40 5.1 85x95 32

650 30 3.6 10.9 1.3 40 5.1 85x95 32
900 30 3.7 11.1 1.9 60 4.5 85x125 32
600 900 60 7.1 21.2 1.2 60 4.2 85x142 32
1050 60 7.2 21.5 1.3 70 3.9 85x155 32
1280 60 7.1 21.4 1.5 70 2.6 85x185 32
1740 60 7.1 21.4 1.6 80 2.4 85x235 32
460 35 2.3 6.9 1.4 40 5.1 85x95 32
620 35 3.1 9.3 1.9 60 4.5 85x125 32
640 55 4.4 13.4 1.5 60 4.2 85x142 32
700 750 55 4.5 13.5 1.6 70 3.9 85x155 32
920 55 4.6 13.8 1.7 80 2.6 85x185 32
1240 60 4.7 18.8 1.6 80 2.4 85x235 32
1700 65 8.8 26.5 1.3 70 2.1 116x185 50
370 30 2.2 6.6 1.8 40 5.5 85x95 32
480 55 4.0 12.0 1.2 60 4.9 85x142 32
500 55 4.1 12.3 1.2 40 4.9 85x142 32
900 560 55 4.2 12.6 1.3 60 4.0 85x155 32
680 55 4.3 12.9 1.3 70 3.2 85x185 32
950 60 5.7 17.1 1.4 70 2.7 85x235 32
1100 50 8.1 24.3 1.3 60 2.5 116x155 50
230 30 2.1 6.3 2.1 40 4.5 85x95 32
320 55 3.3 10.0 1.2 60 2.8 85x142 32
360 55 3.2 10.0 1.2 60 2.6 85x155 32
410 65 3.7 11.0 1.1 45 2.5 85x155 32
1100
420 65 3.7 11.0 1.1 45 2.5 85x155 32
450 60 4.0 12.0 1.1 70 2.4 85x185 32
610 60 5.3 15.9 1.2 70 2.3 85x235 32
760 70 7.4 22.2 1.1 60 1.8 116x155 50
160 35 3.1 9.3 2.1 40 4.1 85x95 32
220 55 3.2 9.6 1.4 60 3.7 85x142 32
250 55 3.5 10.5 1.3 60 3.5 85x155 32
1350
310 55 3.4 10.0 1.3 70 3.2 85x185 32
420 60 3.5 10.5 1.4 70 2.7 85x235 32
530 60 7.2 21.6 1.4 60 2.0 116x155 50
130 30 1.5 4.5 2.3 40 4.2 85x95 32
180 55 3.5 10.5 1.3 50 3.7 85x142 32
220 55 4.0 12.0 1.3 60 3.5 85x155 32
1500
260 55 4.1 12.3 1.4 60 3.2 85x185 32
360 60 3.6 10.8 1.6 70 2.7 85x235 32
460 60 3.1 9.3 1.7 60 2.0 116x155 50
90 30 1.6 4.8 2.5 60 4.6 85x95 32
140 55 2.0 6.0 2.4 70 3.5 85x155 32
1800
240 60 2.9 8.7 1.7 70 2.7 85x235 32
350 50 3.0 9.0 2.0 70 2.0 116x185 50
75 20 0.5 1.5 5.0 60 5.8 85x125 32
90 40 0.5 1.5 2.5 60 4.5 85x185 32
2200
150 40 0.5 1.5 2.5 70 3.3 85x235 32
220 40 0.6 1.8 2.3 70 2.7 116x185 50

6
 DC LINK CAPACITORS
TYPE KNG2047 - KNG3047, KNG2048 - KNG3048

DIMENSIONS

KNG2047, KNG3047

6±1
M6 x 10
D±1
35

H±1

P ± 0.5
16

M12

KNG2048, KNG3048
23 ± 1

SCREW TERMINAL M8
D±1
35

H±1

P ± 0.5
16

M12

7
 HIGH POWER DC LINK CAPACITORS
TYPE KNG4910, KNG4914

APPLICATIONS

SWITCHING MODE POWER SUPPLIES (SMPS)

WIND PLANTS
SOLAR POWER PLANTS
MOTOR DRIVES
INDUCTION HEATERS
FREQUENCY INVERTERS
UNINTERRUPTIBLE POWER SUPPLIES (UPS)

FEATURES REFERENCE STANDARD

FOR HARSH ENVIRONMENT IEC 61071

SELF-HEALING PROPERTIES
HIGH RIPPLE CURRENT
HIGH RELIABILITY
VERY LOW LOSSES

SPECIFICATIONS
RATED CAPACITANCE 0.22 mF UP TO 100 mF
CAPACITANCE TOLERANCE ± 5 %, ± 10 %
RATED VOLTAGE UNDC 250 V DC, 300 V DC, 450 V DC, 630 V DC, 750 V DC, 875 V DC

TEST VOLTAGE TERMINAL TO TERMINAL = 1.5xUNDC, 10 s

SELF-INDUCTANCE < 1nH PER mm OF PITCH

INSULATION RESISTANCE BETWEEN RxC ≥ 30 000 s AFTER 1 min

TERMINALS AT 100 V FOR UNDC < 500 V DC
AT 500 V FOR UNDC ≥ 500 V DC

OPERATING TEMPERATURE RANGE -40 °C to +110 °C

CLIMATIC CATEGORY 40/110/56 according to IEC 60068-1

LIFE EXPECTANCY ≥100 000 hours at UNDC , θhs = 70 °C

8
 HIGH POWER DC LINK CAPACITORS
TYPE KNG4910, KNG4914

GENERAL CHARACTERISTICS

CAPACITANCE RANGE
UNDC @ 85 °C = 250 V DC, Uop@ 70 °C = 300 V DC
(2)
CN (1)
Dimensions (mm) tan(δ)@1kHz (3) ESR@10 kHz (4) Imax@10 kHz (5) (dU/dt)max Î
(µF) L H W P P1 (x10-4) (mW) (A) (V/µs) (A)
1.5 32.0 16.0 7.5 27.5 – 10 27.0 3.8 32 48
2.2 32.0 17.0 9.0 27.5 – 10 19.0 4.8 32 70
3 32.0 19.0 10.0 27.5 – 10 14.5 5.8 32 96
3.3 32.0 20.0 11.0 27.5 – 10 13.8 6.2 32 106
4.7 32.0 22.0 13.0 27.5 – 10 10.0 7.8 32 150
5 32.0 22.0 13.0 27.5 – 10 9.5 8.0 32 160
5.6 32.0 23.5 14.0 27.5 – 10 8.6 8.7 32 179
6 32.0 24.5 15.0 27.5 – 10 8.2 9.2 32 192
6.8 32.0 24.5 15.0 27.5 – 10 7.4 9.7 32 218
8 32.0 26.5 17.0 27.5 – 10 6.5 10.9 32 256
8.2 32.0 28.0 18.0 27.5 – 10 6.3 11.4 32 262
10 32.0 28.0 18.0 27.5 – 10 5.3 12.0 32 320
12 32.0 32.0 18.0 27.5 – 10 4.5 12.0 32 384
15 32.0 35.0 20.0 27.5 -/10.2 10 3.7 16.6 32 480
18 32.0 35.5 24.0 27.5 -/10.2 10 3.2 18.7 32 576
20 32.0 40.0 25.0 27.5 -/10.2 10 3.0 20.4 32 640
10 42.0 27.0 16.0 37.5 – 15 9.2 10.1 22 220
12 42.0 27.0 16.0 37.5 – 15 8.0 10.8 22 264
15 42.0 31.0 18.0 37.5 10.2 15 6.5 12.9 22 330
18 42.0 38.0 21.0 37.5 10.2 15 5.6 15.0 22 396
20 42.0 38.0 21.0 37.5 10.2 15 5.1 15.8 22 440
22 42.0 38.0 21.0 37.5 10.2 15 4.7 16.4 22 484
25 42.0 43.0 28.0 37.5 10.2 15 4.2 17.7 22 550
30 42.0 43.0 28.0 37.5 10.2 15 3.7 18.9 22 660
35 42.0 43.0 28.0 37.5 10.2 15 3.3 20.0 22 770
40 42.0 45.0 30.0 37.5 10.2/20.3 15 3.0 21.8 22 880
50 42.0 50.0 36.0 37.5 10.2/20.3 15 2.6 25.1 22 1100
55 42.0 50.0 36.0 37.5 10.2/20.3 15 2.5 25.6 22 1210
55 57.5 45.0 30.0 52.5 20.3 20 3.0 24.1 15 825
60 57.5 45.0 30.0 52.5 20.3 20 2.8 24.9 15 900
70 57.5 50.0 35.0 52.5 20.3 20 2.5 28.2 15 1050
75 57.5 50.0 35.0 52.5 20.3 20 2.4 28.8 15 1125
80 57.5 50.0 35.0 52.5 20.3 20 2.3 29.4 15 1200
90 57.5 55.0 40.0 52.5 20.3 20 2.1 31.7 15 1350
100 57.5 55.0 40.0 52.5 20.3 20 1.9 33.3 15 1500

NOTES:
(1)
CAPACITANCE VALUE MEASURED AT 1 kHz. INTERMEDIATE CAPACITANCE VALUES AVAILABLE ON REQUEST.
(2)
NOMINAL DIMENSIONS.
(3)
MAXIMUM tan(δ) VALUES MEASURED AT 1 kHz.
(4)
TYPICAL EQUIVALENT SERIES RESISTANCE AT 10 kHz.
(5)
MAXIMUM R.M.S. CURRENT AT 10 kHz, θamb = 70°C FOR Δθcase≤ 20°C.

9
 HIGH POWER DC LINK CAPACITORS
TYPE KNG4910, KNG4914

GENERAL CHARACTERISTICS

CAPACITANCE RANGE
UNDC @ 85 °C = 300 V DC, Uop@ 70 °C = 450 V DC
(1) (2)
CN Dimensions (mm) tan(δ)@1kHz (3) ESR@10 kHz (4) Imax@10 kHz (5) (dU/dt)max Î
(µF) L H W P P1 (x10-4) (mW) (A) (V/µs) (A)
1 32.0 16.0 7.5 27.5 – 10 36.0 3.3 36 36
2.2 32.0 19.0 10.0 27.5 – 10 16.5 5.5 36 79
3.3 32.0 21.0 12.0 27.5 – 10 12.0 6.9 36 119
4 32.0 23.5 14.0 27.5 – 10 11.5 7.9 36 144
4.7 32.0 24.5 15.0 27.5 – 10 9.0 8.8 36 169
5 32.0 24.5 15.0 27.5 – 10 8.7 9.0 36 180
5.6 32.0 26.5 17.0 27.5 – 10 7.9 9.9 36 202
6 32.0 26.5 17.0 27.5 – 10 7.5 10.1 36 216
6.8 32.0 28.0 18.0 27.5 – 10 6.8 11.0 36 245
8 32.0 32.0 18.0 27.5 – 10 6.0 12.0 36 288
8.2 32.0 32.0 18.0 27.5 – 10 5.9 12.3 36 295
10 32.0 33.0 20.0 27.5 -/10.2 10 5.0 14.0 36 360
12 32.0 35.5 24.0 27.5 -/10.2 10 4.2 16.3 33 432
15 32.0 40.0 25.0 27.5 -/10.2 10 3.4 19.2 36 540
8.2 42.0 27.0 16.0 37.5 – 15 10.4 9.5 25 205
9 42.0 31.0 18.0 37.5 10.2 15 9.3 10.8 25 225
10 42.0 31.0 18.0 37.5 10.2 15 8.5 11.3 25 250
11 42.0 31.0 18.0 37.5 10.2 15 7.7 11.8 25 275
12 42.0 31.0 18.0 37.5 10.2 15 7.0 12.4 25 300
15 42.0 38.0 21.0 37.5 10.2 15 5.7 14.9 25 375
18 42.0 38.0 21.0 37.5 10.2 15 4.8 16.2 25 450
20 42.0 43.0 28.0 37.5 10.2 15 4.3 17.5 25 500
22 42.0 43.0 28.0 37.5 10.2 15 3.9 18.4 25 550
25 42.0 43.0 28.0 37.5 10.2 15 3.5 19.4 25 625
30 42.0 45.0 30.0 37.5 10.2/20.3 15 2.9 22.2 25 750
35 42.0 50.0 36.0 37.5 10.2/20.3 15 2.6 25.1 25 875
40 42.0 50.0 36.0 37.5 10.2/20.3 15 2.3 26.7 25 1000
40 57.5 45.0 30.0 52.5 20.3 20 3.1 23.7 17 680
45 57.5 45.0 30.0 52.5 20.3 20 2.8 24.9 17 765
50 57.5 50.0 35.0 52.5 20.3 20 2.6 27.7 17 850
55 57.5 50.0 35.0 52.5 20.3 20 2.4 28.8 17 935
60 57.5 50.0 35.0 52.5 20.3 20 2.2 30.1 17 1020
65 57.5 55.0 40.0 52.5 20.3 20 2.1 31.7 17 1105
70 57.5 55.0 40.0 52.5 20.3 20 2.0 32.4 17 1190
75 57.5 55.0 40.0 52.5 20.3 20 1.9 33.3 17 1275

NOTES:
(1)
CAPACITANCE VALUE MEASURED AT 1 kHz. INTERMEDIATE CAPACITANCE VALUES AVAILABLE ON REQUEST.
(2)
NOMINAL DIMENSIONS.
(3)
MAXIMUM tan(δ) VALUES MEASURED AT 1 kHz.
(4)
TYPICAL EQUIVALENT SERIES RESISTANCE AT 10 kHz.
(5)
MAXIMUM R.M.S. CURRENT AT 10 kHz, θamb = 70°C FOR Δθcase≤ 20°C.

10
 HIGH POWER DC LINK CAPACITORS
TYPE KNG4910, KNG4914

GENERAL CHARACTERISTICS

CAPACITANCE RANGE
UNDC @ 85 °C = 450 V DC, Uop@ 70 °C = 630 V DC
(1) (2)
CN Dimensions (mm) tan(δ)@1kHz (3) ESR@10 kHz (4) Imax@10 kHz (5) (dU/dt)max Î
(µF) L H W P P1 (x10-4) (mW) (A) (V/µs) (A)
0.82 32.0 16.0 7.5 27.5 – 10 38.0 3.2 45 37
1 32.0 17.0 9.0 27.5 – 10 32.0 3.7 45 45
1.5 32.0 19.0 10.0 27.5 – 10 21.0 4.8 45 68
2 32.0 21.0 12.0 27.5 – 10 16.5 5.9 45 90
3.3 32.0 24.5 15.0 27.5 – 10 10.5 8.2 45 149
4 32.0 26.5 17.0 27.5 – 10 9.0 9.2 45 180
4.7 32.0 28.0 18.0 27.5 – 10 7.5 10.5 45 212
5 32.0 28.0 18.0 27.5 – 10 7.3 10.6 45 225
5.6 32.0 32.0 18.0 27.5 – 10 6.4 11.8 45 252
6 32.0 33.0 20.0 27.5 –/10.2 10 6.2 12.6 45 270
6.8 32.0 33.0 20.0 27.5 –/10.2 10 5.6 13.2 45 306
8 32.0 35.5 24.0 27.5 –/10.2 10 4.9 15.1 45 360
8.2 32.0 35.5 24.0 27.5 –/10.2 10 4.8 15.3 45 369
10 32.0 40.0 25.0 27.5 –/10.2 10 4.1 17.5 45 450
5 42.0 27.0 16.0 37.5 – 15 13.0 8.5 32 160
5.6 42.0 27.0 16.0 37.5 – 15 11.5 9.0 32 179
6 42.0 31.0 18.0 37.5 10.2 15 10.8 10.0 32 192
6.8 42.0 31.0 18.0 37.5 10.2 15 9.5 10.7 32 218
7.5 42.0 31.0 18.0 37.5 10.2 15 8.7 11.1 32 240
8 42.0 38.0 21.0 37.5 10.2 15 8.1 12.5 32 256
8.2 42.0 38.0 21.0 37.5 10.2 15 7.9 12.7 32 262
10 42.0 38.0 21.0 37.5 10.2 15 6.6 13.8 32 320
12 42.0 38.0 21.0 37.5 10.2 15 5.6 15.0 32 384
14 42.0 43.0 28.0 37.5 10.2 15 4.9 16.4 32 448
15 42.0 43.0 28.0 37.5 10.2 15 4.6 16.9 32 480
18 42.0 43.0 28.0 37.5 10.2 15 3.9 18.4 32 576
20 42.0 45.0 30.0 37.5 10.2/20.3 15 3.5 20.2 32 640
22 42.0 50.0 36.0 37.5 10.2/20.3 15 3.2 22.6 32 704
25 42.0 50.0 36.0 37.5 10.2/20.3 15 2.9 23.8 32 800
25 57.5 45.0 30.0 52.5 20.3 20 3.7 21.7 22 550
30 57.5 45.0 30.0 52.5 20.3 20 3.2 23.3 22 660
35 57.5 50.0 35.0 52.5 20.3 20 2.8 26.7 22 770
40 57.5 50.0 35.0 52.5 20.3 20 2.5 28.2 22 880
45 57.5 55.0 40.0 52.5 20.3 20 2.3 30.3 22 990
50 57.5 55.0 40.0 52.5 20.3 20 2.1 31.7 22 1100

NOTES:
(1)
CAPACITANCE VALUE MEASURED AT 1 kHz. INTERMEDIATE CAPACITANCE VALUES AVAILABLE ON REQUEST.
(2)
NOMINAL DIMENSIONS.
(3)
MAXIMUM tan(δ) VALUES MEASURED AT 1 kHz.
(4)
TYPICAL EQUIVALENT SERIES RESISTANCE AT 10 kHz.
(5)
MAXIMUM R.M.S. CURRENT AT 10 kHz, θamb = 70°C FOR Δθcase≤ 20°C.

11
 HIGH POWER DC LINK CAPACITORS
TYPE KNG4910, KNG4914

GENERAL CHARACTERISTICS

CAPACITANCE RANGE
UNDC @ 85 °C = 630 V DC, Uop@ 70 °C = 800 V DC
(1) (2)
CN Dimensions (mm) tan(δ)@1kHz (3) ESR@10 kHz (4) Imax@10 kHz (5) (dU/dt)max Î
(µF) L H W P P1 (x10-4) (mW) (A) (V/µs) (A)
0.56 32.0 16.0 7.5 27.5 – 10 48.0 2.9 54 30
0.68 32.0 17.0 9.0 27.5 – 10 40.0 3.3 54 37
0.82 32.0 17.0 9.0 27.5 – 10 33.0 3.6 54 44
1 32.0 19.0 10.0 27.5 – 10 26.8 4.3 54 54
1.2 32.0 21.0 12.0 27.5 – 10 23.0 5.0 54 65
2 32.0 24.5 15.0 27.5 – 10 14.0 7.1 54 108
2.2 32.0 24.5 15.0 27.5 – 10 13.0 7.3 54 119
3 32.0 28.0 18.0 27.5 – 10 9.8 9.2 54 162
3.3 32.0 28.0 18.0 27.5 – 10 8.8 9.7 54 178
4 32.0 32.0 18.0 27.5 – 10 7.2 11.2 54 216
4.7 32.0 33.0 20.0 27.5 -/10.2 10 6.6 12.2 54 254
5 32.0 35.0 20.0 27.5 -/10.2 10 6.3 12.7 54 270
5.6 32.0 35.5 24.0 27.5 -/10.2 10 5.8 13.9 54 302
6 32.0 35.5 24.0 27.5 -/10.2 10 5.5 14.3 54 324
6.8 32.0 40.0 25.0 27.5 -/10.2 10 4.9 16.0 54 258
7 32.0 40.0 25.0 27.5 -/10.2 10 4.9 16.0 54 266
4 42.0 27.0 16.0 37.5 – 15 12.0 8.8 38 152
4.7 42.0 31.0 18.0 37.5 10.2 15 10.2 10.3 38 179
5 42.0 31.0 18.0 37.5 10.2 15 9.5 10.7 38 190
5.6 42.0 32.0 19.0 37.5 10.2 15 8.7 11.4 38 213
6 42.0 32.0 19.0 37.5 10.2 15 8.2 11.7 38 228
6.8 42.0 38.0 21.0 37.5 10.2 15 7.3 13.2 38 258
8 42.0 38.0 21.0 37.5 10.2 15 6.5 14.0 38 304
8.2 42.0 38.0 21.0 37.5 10.2 15 6.3 14.2 38 312
10 42.0 43.0 28.0 37.5 10.2 15 5.2 15.9 38 380
12 42.0 43.0 28.0 37.5 10.2 15 4.3 17.5 38 456
15 42.0 50.0 36.0 37.5 10.2/20.3 15 3.6 21.3 38 570
18 42.0 50.0 36.0 37.5 10.2/20.3 15 3.1 23.0 38 684
20 42.0 50.0 36.0 37.5 10.2/20.3 15 2.8 24.2 38 760
18 57.5 45.0 30.0 52.5 20.3 20 4.5 19.7 26 468
20 57.5 45.0 30.0 52.5 20.3 20 4.1 20.6 26 520
22 57.5 50.0 35.0 52.5 20.3 20 3.8 22.9 26 572
25 57.5 50.0 35.0 52.5 20.3 20 3.4 24.2 26 650
30 57.5 55.0 40.0 52.5 20.3 20 2.9 26.9 26 780

NOTES:
(1)
CAPACITANCE VALUE MEASURED AT 1 kHz. INTERMEDIATE CAPACITANCE VALUES AVAILABLE ON REQUEST.
(2)
NOMINAL DIMENSIONS.
(3)
MAXIMUM tan(δ) VALUES MEASURED AT 1 kHz.
(4)
TYPICAL EQUIVALENT SERIES RESISTANCE AT 10 kHz.
(5)
MAXIMUM R.M.S. CURRENT AT 10 kHz, θamb = 70°C FOR Δθcase≤ 20°C.

12
 HIGH POWER DC LINK CAPACITORS
TYPE KNG4910, KNG4914

GENERAL CHARACTERISTICS

CAPACITANCE RANGE
UNDC @ 85 °C = 750 V DC, Uop@ 70 °C = 900 V DC
(1) (2)
CN Dimensions (mm) tan(δ)@1kHz (3) ESR@10 kHz (4) Imax@10 kHz (5) (dU/dt)max Î
(µF) L H W P P1 (x10-4) (mW) (A) (V/µs) (A)
0.39 32.0 16.0 7.5 27.5 – 10 60.0 2.6 63 25
0.47 32.0 17.0 9.0 27.5 – 10 50.0 3.0 63 30
0.56 32.0 17.0 9.0 27.5 – 10 41.5 3.2 63 35
0.68 32.0 19.0 10.0 27.5 – 10 35.0 3.7 63 43
0.82 32.0 20.0 11.0 27.5 – 10 30.0 4.2 63 52
1 32.0 21.0 12.0 27.5 – 10 25.5 4.7 63 63
1.5 32.0 24.5 15.0 27.5 – 10 17.0 6.4 63 95
2 32.0 26.5 17.0 27.5 – 10 13.0 7.7 63 126
2.2 32.0 26.5 17.0 27.5 – 10 11.6 8.1 63 139
3 32.0 33.0 20.0 27.5 -/10.2 10 8.8 10.6 63 189
3.3 32.0 33.0 20.0 27.5 -/10.2 10 8.2 10.9 63 208
4 32.0 35.5 24.0 27.5 -/10.2 10 6.9 12.7 63 252
4.7 32.0 40.0 25.0 27.5 -/10.2 10 6.0 14.4 63 296
5 32.0 40.0 25.0 27.5 -/10.2 10 5.6 14.9 63 315
2.2 42.0 27.0 16.0 37.5 – 15 17.0 7.4 45 140
3 42.0 27.0 16.0 37.5 – 15 13.0 8.5 45 135
3.3 42.0 31.0 18.0 37.5 10.2 15 12.3 9.4 45 149
4 42.0 32.0 19.0 37.5 10.2 15 10.5 10.4 45 180
4.7 42.0 38.0 21.0 37.5 10.2 15 9.0 11.9 45 212
5 42.0 38.0 21.0 37.5 10.2 15 8.5 12.2 45 225
5.6 42.0 38.0 21.0 37.5 10.2 15 7.7 12.8 45 252
6 42.0 38.0 21.0 37.5 10.2 15 7.3 13.2 45 270
6.8 42.0 43.0 28.0 37.5 10.2 15 6.6 14.1 45 306
8 42.0 43.0 28.0 37.5 10.2 15 5.8 15.1 45 360
8.2 42.0 43.0 28.0 37.5 10.2 15 5.7 15.2 45 369
9 42.0 45.0 30.0 37.5 10.2 15 5.3 16.4 45 405
10 42.0 45.0 30.0 37.5 10.2/20.3 15 4.8 17.3 45 450
12 42.0 50.0 36.0 37.5 10.2/20.3 15 4.1 20.0 45 540
14 42.0 50.0 36.0 37.5 10.2/20.3 15 3.7 21.0 45 630
14 57.5 45.0 30.0 52.5 20.3 20 4.8 19.0 30 420
15 57.5 45.0 30.0 52.5 20.3 20 4.6 19.4 30 450
18 57.5 50.0 35.0 52.5 20.3 20 3.8 22.9 30 540
20 57.5 50.0 35.0 52.5 20.3 20 3.5 23.9 30 600
22 57.5 55.0 40.0 52.5 20.3 20 3.2 25.6 30 660
25 57.5 55.0 40.0 52.5 20.3 20 3.0 26.5 30 750

NOTES:
(1)
CAPACITANCE VALUE MEASURED AT 1 kHz. INTERMEDIATE CAPACITANCE VALUES AVAILABLE ON REQUEST.
(2)
NOMINAL DIMENSIONS.
(3)
MAXIMUM tan(δ) VALUES MEASURED AT 1 kHz
(4)
TYPICAL EQUIVALENT SERIES RESISTANCE AT 10 kHz.
(5)
MAXIMUM R.M.S. CURRENT AT 10 kHz, θamb = 70°C FOR Δθcase≤ 20°C.

13
 HIGH POWER DC LINK CAPACITORS
TYPE KNG4910, KNG4914

GENERAL CHARACTERISTICS

CAPACITANCE RANGE
UNDC @ 85 °C = 875 V DC, Uop@ 70 °C = 1050 V DC
(1) (2)
CN Dimensions (mm) tan(δ)@1kHz (3) ESR@10 kHz (4) Imax@10 kHz (5) (dU/dt)max Î
(µF) L H W P P1 (x10-4) (mW) (A) (V/µs) (A)
0.22 32.0 16.0 7.5 27.5 – 10 80.0 2.2 72 16
0.33 32.0 17.0 9.0 27.5 – 10 55.0 2.8 72 24
0.47 32.0 19.0 10.0 27.5 – 10 42.0 3.4 72 34
0.56 32.0 19.0 10.0 27.5 – 10 37.0 3.6 72 40
0.68 32.0 20.0 11.0 27.5 – 10 30.0 4.2 72 49
0.82 32.0 21.0 12.0 27.5 – 10 25.0 4.8 72 59
1 32.0 22.0 13.0 27.5 – 10 22.0 5.2 72 72
1.5 32.0 26.5 17.0 27.5 – 10 15.0 7.2 72 108
2 32.0 28.0 18.0 27.5 – 10 11.5 8.5 72 144
2.2 32.0 32.0 18.0 27.5 – 10 10.5 9.2 72 158
3 32.0 35.5 24.0 27.5 -/10.2 10 7.8 12.0 72 216
3.3 32.0 35.5 24.0 27.5 -/10.2 10 7.3 12.4 72 238
4 32.0 40.0 25.0 27.5 -/10.2 10 6.3 14.1 72 288
2 42.0 27.0 16.0 37.5 – 15 16.0 7.6 51 102
2.2 42.0 27.0 16.0 37.5 – 15 15.0 7.9 51 112
3 42.0 31.0 18.0 37.5 10.2 15 11.5 9.7 51 153
3.3 42.0 38.0 21.0 37.5 10.2 15 10.5 11.0 51 168
4 42.0 38.0 21.0 37.5 10.2 15 9.0 11.9 51 204
4.7 42.0 38.0 21.0 37.5 10.2 15 7.6 12.9 51 240
5 42.0 43.0 28.0 37.5 10.2 15 7.0 13.7 51 255
5.6 42.0 43.0 28.0 37.5 10.2 15 6.3 14.5 51 286
6 42.0 43.0 28.0 37.5 10.2 15 6.5 14.2 51 306
6.8 42.0 43.0 28.0 37.5 10.2 15 5.8 15.1 51 347
7.5 42.0 45.0 30.0 37.5 10.2/20.3 15 5.4 16.3 51 383
8 42.0 45.0 30.0 37.5 10.2/20.3 15 5.1 16.7 51 408
8.2 42.0 45.0 30.0 37.5 10.2/20.3 15 5.0 16.9 51 418
9 42.0 50.0 36.0 37.5 10.2/20.3 15 4.6 18.9 51 459
10 42.0 50.0 36.0 37.5 10.2/20.3 15 4.4 19.3 51 510
10 57.5 45.0 30.0 52.5 20.3 20 5.2 18.3 35 350
12 57.5 45.0 30.0 52.5 20.3 20 4.6 19.4 35 420
14 57.5 50.0 35.0 52.5 20.3 20 4.0 22.3 35 490
15 57.5 50.0 35.0 52.5 20.3 20 3.8 22.9 35 525
16 57.5 50.0 35.0 52.5 20.3 20 3.7 23.2 35 560
18 57.5 55.0 40.0 52.5 20.3 20 3.3 25.3 35 630
20 57.5 55.0 40.0 52.5 20.3 20 3.0 26.5 35 700

NOTES:
(1)
CAPACITANCE VALUE MEASURED AT 1 kHz. INTERMEDIATE CAPACITANCE VALUES AVAILABLE ON REQUEST.
(2)
NOMINAL DIMENSIONS.
(3)
MAXIMUM tan(δ) VALUES MEASRED AT 1kHz.
(4)
TYPICAL EQUIVALENT SERIES RESISTANCE AT 10 kHz.
(5)
MAXIMUM R.M.S. CURRENT AT 10 kHz, θamb = 70°C FOR Δθcase≤ 20°C.

14
 HIGH POWER DC LINK CAPACITORS
TYPE KNG4910, KNG4914

DIMENSIONS

KNG4910 (2 pins) KNG4914 (4 pins)

L W L W

H
H

4 or 6
4 or 6

P d P d
P1

TERMINAL DIMENSIONS MAX. BOX DIMENSIONS

P TOLERANCE P1 TOLERANCE d TOLERANCE Lmax Hmax Wmax
(mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm)
27.5 ±0.5 – – 0.8 ±0.05 L + 0.5 H + 0.2 W + 0.5
27.5 ±0.5 10.2 ±0.5 1 OR 1.2 ±0.05 L + 0.5 H + 0.2 W + 0.5
37.5 ±0.5 10.2 ±0.5 1 OR 1.2 ±0.05 L + 0.5 H + 0.5 W + 0.5
37.5 ±0.5 20.3 ±0.5 1 OR 1.2 ±0.05 L + 0.5 H + 0.5 W + 0.5
52.5 ±0.5 20.3 ±0.5 1.2 ±0.05 L + 1.0 H + 1.0 W + 1.0

CONSTRUCTION

DIELECTRIC: POLYPROPYLENE FILM

CAPACITOR ELECTRODES: VACUUM-DEPOSITED
CASING: PLASTIC CASE WITH FLAME-RETARDANT EPOXY RESIN SEALING (UL 94 V-0)
TERMINAL: PARALLEL TINNED COPPER (2 OR 4 PINS)

INTERNAL CONSTRUCTION

FIRST CONTACT LAYER

SECOND CONTACT LAYER

POLYPROPYLENE FILM DIELECTRIC METALLIZED LAYER

METAL-SPRAYED CONTACT LAYERS

15
 HIGH DENSITY DC LINK CAPACITORS
TYPE KNG1910, KNG1914

APPLICATIONS

HYBRID VEHICLES
WIND PLANTS
SOLAR POWER PLANTS
ELECTRIC ENERGY GENERATION FROM SEA WAVES
MEDICAL EQUIPMENT
INDUSTRIAL EQUIPMENT
CAR ELECTRONICS
RAILWAYS AND TURBINES (GENERATOR)
FREQUENCY INVERTERS
DC FILTERING APPLICATIONS

FEATURES REFERENCE STANDARD

HIGH CAPACITANCE IEC 61071

SELF-HEALING PROPERTIES
HIGH RELIABILITY
LOW LOSSES
LOW DISSIPATION FACTOR OF DIELECTRIC

SPECIFICATIONS
RATED CAPACITANCE 0.1 mF UP TO 480 mF
CAPACITANCE TOLERANCE ± 5 %, ± 10 %
RATED VOLTAGE 450 V DC, 700 V DC, 800 V DC, 900 V DC, 1100 V DC, 1300 V DC
TEST VOLTAGE TERMINAL TO TERMINAL = 1.5xUNDC, 10 s
SELF-INDUCTANCE < 1nH PER mm OF PITCH

INSULATION RESISTANCE BETWEEN RxC ≥ 30 000 s AFTER 1 min

TERMINALS AT 100 V FOR UNDC < 500 V DC
AT 500 V FOR UNDC ≥ 500 V DC

MAX. PEAK-TO-PEAK VOLTAGE 0.2xUNDC

OPERATING TEMPERATURE RANGE -40 °C to +85 °C

CLIMATIC CATEGORY 40/85/56 according to IEC 60068-1

LIFE EXPECTANCY ≥100 000 hours at UNDC , θhs = 70 °C

RATED TEMPERATURE +85 °C

MAX. HOT SPOT TEMPERATURE 105 °C

16
 HIGH DENSITY DC LINK CAPACITORS
TYPE KNG1910, KNG1914

GENERAL CHARACTERISTICS

CAPACITANCE RANGE
UNDC @ 85 °C = 450 V DC, Uop@ 70 °C = 500 V DC, Uop@ 105 °C = 300 V DC

CN (1)
Dimensions (mm) (2) tan(δ)@1kHz (3) ESR@10 kHz (4) Imax@10 kHz (5) (dU/dt)max Î
(µF) L H W P P1 (x10-4) (mW) (A) (V/µs) (A)
1 32.0 17.0 9.0 27.5 – 15 40.0 3.3 27 27
2 32.0 17.0 9.0 27.5 – 15 35.0 3.5 27 54
3 32.0 17.0 9.0 27.5 – 15 27.0 4.0 27 81
4 32.0 19.0 10.0 27.5 – 15 22.0 4.7 27 108
5 32.0 21.0 12.0 27.5 – 15 18.5 5.5 27 135
6 32.0 21.0 12.0 27.5 – 15 16.7 5.8 27 162
7 32.0 22.0 13.0 27.5 – 15 15.2 6.3 27 189
8 32.0 23.5 14.0 27.5 – 15 14.0 6.8 27 216
9 32.0 24.5 15.0 27.5 – 15 12.8 7.4 27 243
10 32.0 26.5 17.0 27.5 – 20 11.7 8.1 27 270
12 32.0 28.0 18.0 27.5 – 20 10.2 9.0 27 324
14 32.0 32.0 18.0 27.5 – 20 9.0 10.0 27 378
15 32.0 32.0 18.0 27.5 – 20 8.5 10.3 27 405
20 32.0 35.5 24.0 27.5 -/10.2 20 6.5 13.1 27 540
25 32.0 40.0 25.0 27.5 -/10.2 20 5.3 15.4 27 675
28 32.0 40.0 25.0 27.5 -/10.2 20 4.8 16.1 27 756
15 42.0 27.0 16.0 37.5 – 25 10.5 9.4 20 300
20 42.0 31.0 18.0 37.5 10.2 25 8.0 11.6 20 400
25 42.0 32.0 19.0 37.5 10.2 25 7.0 12.7 20 500
30 42.0 38.0 21.0 37.5 10.2 25 6.5 14.0 20 600
35 42.0 43.0 28.0 37.5 10.2 25 6.0 14.8 20 700
40 42.0 43.0 28.0 37.5 10.2 25 5.4 15.6 20 800
45 42.0 43.0 28.0 37.5 10.2 25 4.8 16.6 20 900
50 42.0 43.0 28.0 37.5 10.2 25 4.5 17.1 20 1000
55 42.0 45.0 30.0 37.5 10.2/20.3 25 4.2 18.4 20 1100
60 42.0 50.0 36.0 37.5 10.2/20.3 25 4.0 20.2 20 1200
65 42.0 50.0 36.0 37.5 10.2/20.3 25 3.8 20.8 20 1300
70 42.0 50.0 36.0 37.5 10.2/20.3 25 3.5 21.6 20 1400
75 42.0 50.0 36.0 37.5 10.2/20.3 25 3.3 22.0 20 1500
70 57.5 45.0 30.0 52.5 20.3 40 4.7 19.2 13 910
75 57.5 45.0 30.0 52.5 20.3 40 4.4 19.9 13 975
80 57.5 45.0 30.0 52.5 20.3 40 4.2 20.3 13 1040
90 57.5 50.0 35.0 52.5 20.3 40 3.8 22.9 13 1170
100 57.5 50.0 35.0 52.5 20.3 40 3.5 23.9 13 1300
110 57.5 50.0 35.0 52.5 20.3 40 3.2 25.0 13 1430
120 57.5 55.0 40.0 52.5 20.3 40 3.0 26.5 13 1560
130 57.5 55.0 40.0 52.5 20.3 40 2.9 26.9 13 1690
480 59.0 59.0 130.0 52.5 20.3x5 45 1.0 71.0 13 6240

NOTES:
(1)
CAPACITANCE VALUE MEASURED AT 1 kHz. INTERMEDIATE CAPACITANCE VALUES AVAILABLE ON REQUEST.
(2)
NOMINAL DIMENSIONS.
(3)
MAXIMUM tan(δ) VALUES.
(4)
TYPICAL EQUIVALENT SERIES RESISTANCE AT 10 kHz.
(5)
MAXIMUM R.M.S. CURRENT AT 10 kHz, θamb = 70°C FOR Δθcase≤ 20°C.

17
 HIGH DENSITY DC LINK CAPACITORS
TYPE KNG1910, KNG1914

GENERAL CHARACTERISTICS

CAPACITANCE RANGE
UNDC @ 85 °C = 700 V DC, Uop@ 70 °C = 800 V DC, Uop@ 105 °C = 500 V DC

CN(1)
Dimensions (mm) (2) tan(δ)@1kHz (3) ESR@10 kHz (4) Imax@10 kHz (5) (dU/dt)max Î
(µF) L H W P P1 (x10-4) (mW) (A) (V/µs) (A)
1 32.0 17.0 9.0 27.5 – 10 40.0 3.3 30 30
2 32.0 17.0 9.0 27.5 – 10 35.0 3.5 30 60
3 32.0 19.0 10.0 27.5 – 10 25.0 4.4 30 90
4 32.0 21.0 12.0 27.5 – 10 19.0 5.5 30 120
5 32.0 22.0 13.0 27.5 – 10 15.5 6.2 30 150
6 32.0 24.5 15.0 27.5 – 15 13.0 7.3 30 180
7 32.0 24.5 15.0 27.5 – 15 11.5 7.8 30 210
8 32.0 26.5 17.0 27.5 – 15 10.2 8.7 30 240
9 32.0 28.0 18.0 27.5 – 15 9.3 9.4 30 270
10 32.0 28.0 18.0 27.5 – 15 8.5 9.8 30 300
12 32.0 32.0 18.0 27.5 – 15 7.3 11.1 30 360
14 32.0 35.0 20.0 27.5 -/10.2 15 6.5 12.5 30 420
15 32.0 35.0 20.0 27.5 -/10.2 15 6.1 12.9 30 450
18 32.0 35.5 24.0 27.5 -/10.2 15 5.1 14.8 30 540
20 32.0 40.0 25.0 27.5 -/10.2 15 4.6 16.5 30 600
10 42.0 27.0 16.0 37.5 – 20 14.0 8.2 22 220
12 42.0 27.0 16.0 37.5 – 20 12.0 8.8 22 264
15 42.0 31.0 18.0 37.5 10.2 20 9.8 10.5 22 330
18 42.0 38.0 21.0 37.5 10.2 20 8.2 12.4 22 396
20 42.0 38.0 21.0 37.5 10.2 20 7.4 13.1 22 440
22 42.0 38.0 21.0 37.5 10.2 20 6.8 13.6 22 484
25 42.0 43.0 28.0 37.5 10.2 25 6.1 14.7 22 550
30 42.0 43.0 28.0 37.5 10.2 25 5.7 15.2 22 660
35 42.0 43.0 28.0 37.5 10.2 25 5.0 16.2 22 770
40 42.0 45.0 30.0 37.5 10.2/20.3 25 4.5 17.8 22 880
45 42.0 45.0 30.0 37.5 10.2/20.3 25 4.1 18.7 22 990
50 42.0 50.0 36.0 37.5 10.2/20.3 25 3.8 20.8 22 1100
55 42.0 50.0 36.0 37.5 10.2/20.3 25 3.5 21.6 22 1210
50 57.5 45.0 30.0 52.5 20.3 35 6.0 17.0 15 750
55 57.5 45.0 30.0 52.5 20.3 35 5.5 17.8 15 825
60 57.5 45.0 30.0 52.5 20.3 35 5.1 18.5 15 900
65 57.5 50.0 35.0 52.5 20.3 35 4.7 20.6 15 975
70 57.5 50.0 35.0 52.5 20.3 35 4.4 21.3 15 1050
75 57.5 50.0 35.0 52.5 20.3 35 4.2 21.8 15 1125
80 57.5 55.0 40.0 52.5 20.3 35 4.0 22.9 15 1200
85 57.5 55.0 40.0 52.5 20.3 35 3.8 23.5 15 1275
90 57.5 55.0 40.0 52.5 20.3 35 3.6 24.2 15 1350
100 57.5 55.0 40.0 52.5 20.3 35 3.3 25.3 15 1500
360 59.0 59.0 130.0 52.5 20.3x5 40 1.1 67.0 15 5400

NOTES:
(1)
CAPACITANCE VALUE MEASURED AT 1 kHz. INTERMEDIATE CAPACITANCE VALUES AVAILABLE ON REQUEST.
(2)
NOMINAL DIMENSIONS.
(3)
MAXIMUM tan(δ) VALUES.
(4)
TYPICAL EQUIVALENT SERIES RESISTANCE AT 10 kHz.
(5)
MAXIMUM R.M.S. CURRENT AT 10 kHz, θamb = 70°C FOR Δθcase≤ 20°C.

18
 HIGH DENSITY DC LINK CAPACITORS
TYPE KNG1910, KNG1914

GENERAL CHARACTERISTICS

CAPACITANCE RANGE
UNDC @ 85 °C = 800 V DC, Uop@ 70 °C = 950 V DC, Uop@ 105 °C = 550 V DC

CN(1)
Dimensions (mm) (2) tan(δ)@1kHz (3) ESR@10 kHz (4) Imax@10 kHz (5) (dU/dt)max Î
(µF) L H W P P1 (x10-4) (mW) (A) (V/µs) (A)
1 32.0 17.0 9.0 27.5 – 10 40.0 3.3 35 35
2 32.0 19.0 10.0 27.5 – 10 27.0 4.3 35 70
3 32.0 21.0 12.0 27.5 – 10 19.0 5.5 35 105
4 32.0 22.0 13.0 27.5 – 10 15.0 6.3 35 140
5 32.0 24.5 15.0 27.5 – 10 13.0 7.3 35 175
6 32.0 26.5 17.0 27.5 – 10 10.9 8.4 35 210
7 32.0 28.0 18.0 27.5 – 10 9.3 9.4 35 245
8 32.0 32.0 18.0 27.5 – 15 8.1 10.5 35 280
9 32.0 33.0 20.0 27.5 –/10.2 15 7.2 11.7 35 315
10 32.0 35.0 20.0 27.5 –/10.2 15 6.5 12.5 35 350
12 32.0 35.5 24.0 27.5 –/10.2 15 5.4 14.4 35 420
15 32.0 40.0 25.0 27.5 –/10.2 15 4.4 16.9 35 525
8 42.0 27.0 16.0 37.5 – 20 11.5 9.0 25 200
9 42.0 31.0 18.0 37.5 10.2 20 10.5 10.1 25 225
10 42.0 31.0 18.0 37.5 10.2 20 9.5 10.7 25 250
11 42.0 31.0 18.0 37.5 10.2 20 9.0 11.0 25 275
12 42.0 31.0 18.0 37.5 10.2 20 8.5 11.3 25 300
15 42.0 38.0 21.0 37.5 10.2 20 7.2 13.3 25 375
18 42.0 38.0 21.0 37.5 10.2 20 6.2 14.3 25 450
20 42.0 43.0 28.0 37.5 10.2 20 5.7 15.2 25 500
22 42.0 43.0 28.0 37.5 10.2 20 5.5 15.5 25 550
25 42.0 43.0 28.0 37.5 10.2 20 5.0 16.2 25 625
30 42.0 45.0 30.0 37.5 10.2/20.3 20 4.5 18.8 25 750
35 42.0 50.0 36.0 37.5 10.2/20.3 25 3.9 20.5 25 875
40 42.0 50.0 36.0 37.5 10.2/20.3 25 3.5 21.6 25 1000
40 57.5 45.0 30.0 52.5 20.3 30 6.3 16.6 17 680
45 57.5 45.0 30.0 52.5 20.3 30 5.6 17.3 17 765
50 57.5 50.0 35.0 52.5 20.3 30 5.3 19.4 17 850
55 57.5 50.0 35.0 52.5 20.3 30 4.9 20.2 17 935
60 57.5 50.0 35.0 52.5 20.3 30 4.5 21.1 17 1020
65 57.5 55.0 40.0 52.5 20.3 30 4.2 22.4 17 1105
70 57.5 55.0 40.0 52.5 20.3 30 4.0 22.9 17 1190
75 57.5 55.0 40.0 52.5 20.3 30 3.8 23.5 17 1275
220 59.0 59.0 130.0 52.5 20.3x5 35 1.4 60.0 17 3740
270 59.0 59.0 130.0 52.5 20.3x5 35 1.2 65.0 17 4590

NOTES:
(1)
CAPACITANCE VALUE MEASURED AT 1 kHz. INTERMEDIATE CAPACITANCE VALUES AVAILABLE ON REQUEST.
(2)
NOMINAL DIMENSIONS.
(3)
MAXIMUM tan(δ) VALUES.
(4)
TYPICAL EQUIVALENT SERIES RESISTANCE AT 10 kHz.
(5)
MAXIMUM R.M.S. CURRENT AT 10 kHz, θamb = 70°C FOR Δθcase≤ 20°C.

19
 HIGH DENSITY DC LINK CAPACITORS
TYPE KNG1910, KNG1914

GENERAL CHARACTERISTICS

CAPACITANCE RANGE
UNDC @ 85 °C = 900 V DC, Uop@ 70 °C = 1100 V DC, Uop@ 105 °C = 650 V DC

CN(1)
Dimensions (mm) (2) tan(δ)@1kHz (3) ESR@10 kHz (4) Imax@10 kHz (5) (dU/dt)max Î
(µF) L H W P P1 (x10-4) (mW) (A) (V/µs) (A)
1 32.0 17.0 9.0 27.5 – 10 40.0 3.3 40 40
2 32.0 21.0 12.0 27.5 – 10 22.0 5.1 40 80
3 32.0 24.5 15.0 27.5 – 10 17.5 6.3 40 120
4 32.0 26.5 17.0 27.5 – 10 14.0 7.4 40 160
5 32.0 32.0 18.0 27.5 – 10 12.5 8.5 40 200
6 32.0 33.0 20.0 27.5 -/10.2 10 10.5 9.7 40 240
7 32.0 35.5 24.0 27.5 -/10.2 10 9.0 11.2 40 280
8 32.0 35.5 24.0 27.5 -/10.2 10 7.8 12.0 40 320
9 32.0 40.0 25.0 27.5 -/10.2 10 7.0 13.4 40 360
10 32.0 40.0 25.0 27.5 -/10.2 10 6.3 14.1 40 400
5 42.0 27.0 16.0 37.5 – 15 16.5 7.5 29 145
6 42.0 27.0 16.0 37.5 – 15 14.0 8.2 29 174
7 42.0 31.0 18.0 37.5 10.2 15 12.5 9.3 29 203
8 42.0 38.0 21.0 37.5 10.2 15 11.0 10.7 29 232
9 42.0 38.0 21.0 37.5 10.2 15 10.0 11.3 29 261
10 42.0 38.0 21.0 37.5 10.2 15 9.0 11.9 29 290
12 42.0 43.0 28.0 37.5 10.2 15 7.5 13.2 29 348
14 42.0 43.0 28.0 37.5 10.2 15 6.6 14.1 29 406
15 42.0 43.0 28.0 37.5 10.2 15 6.2 14.6 29 435
18 42.0 43.0 28.0 37.5 10.2/20.3 20 5.3 15.8 29 522
20 42.0 45.0 30.0 37.5 10.2/20.3 20 4.8 17.3 29 580
22 42.0 50.0 36.0 37.5 10.2/20.3 20 4.4 19.3 29 638
25 42.0 50.0 36.0 37.5 10.2/20.3 20 4.0 20.2 29 725
30 42.0 50.0 36.0 37.5 10.2/20.3 20 3.5 21.6 29 870
25 57.5 45.0 30.0 52.5 20.3 25 7.0 15.8 20 500
26 57.5 45.0 30.0 52.5 20.3 25 6.8 16.0 20 520
30 57.5 50.0 35.0 52.5 20.3 25 6.0 18.2 20 600
35 57.5 50.0 35.0 52.5 20.3 25 5.5 19.0 20 700
40 57.5 50.0 35.0 52.5 20.3 25 5.0 20.0 20 800
45 57.5 50.0 35.0 52.5 20.3 25 4.8 20.4 20 900
50 57.5 55.0 40.0 52.5 20.3 25 4.5 21.6 20 1000
55 57.5 55.0 40.0 52.5 20.3 25 4.2 22.4 20 1100
60 57.5 55.0 40.0 52.5 20.3 25 3.9 23.2 20 1200
150 59.0 59.0 130.0 52.5 20.3x5 30 2.3 47.0 20 3000
200 59.0 59.0 130.0 52.5 20.3x5 30 1.8 53.0 20 4000

NOTES:
(1)
CAPACITANCE VALUE MEASURED AT 1 kHz. INTERMEDIATE CAPACITANCE VALUES AVAILABLE ON REQUEST.
(2)
NOMINAL DIMENSIONS.
(3)
MAXIMUM tan(δ) VALUES.
(4)
TYPICAL EQUIVALENT SERIES RESISTANCE AT 10 kHz.
(5)
MAXIMUM R.M.S. CURRENT AT 10 kHz, θamb = 70°C FOR Δθcase≤ 20°C.

20
 HIGH DENSITY DC LINK CAPACITORS
TYPE KNG1910, KNG1914

GENERAL CHARACTERISTICS

CAPACITANCE RANGE
UNDC @ 85 °C = 1100 V DC, Uop@ 70 °C = 1350 V DC, Uop@ 105 °C = 800 V DC

CN (1)
Dimensions (mm) (2) tan(δ)@1kHz (3) ESR@10 kHz (4) Imax@10 kHz (5) (dU/dt)max Î
(µF) L H W P P1 (x10-4) (mW) (A) (V/µs) (A)
1 32.0 19.0 10.0 27.5 – 10 35.0 3.7 50 50
1.2 32.0 21.0 12.0 27.5 – 10 29.0 4.4 50 60
2 32.0 24.5 15.0 27.5 – 10 18.0 6.2 50 100
2.2 32.0 24.5 15.0 27.5 – 10 17.5 6.3 50 110
3 32.0 28.0 18.0 27.5 – 10 13.5 7.8 50 150
3.3 32.0 32.0 18.0 27.5 – 10 12.8 8.4 50 165
4 32.0 32.0 18.0 27.5 – 10 12.0 8.7 50 200
4.7 32.0 33.0 20.0 27.5 -/10.2 10 10.5 9.7 50 235
5 32.0 33.0 20.0 27.5 -/10.2 10 10.0 9.9 50 250
6 32.0 35.5 24.0 27.5 -/10.2 10 8.5 11.5 50 300
7 32.0 40.0 25.0 27.5 -/10.2 10 7.5 12.9 50 350
8 32.0 40.0 25.0 27.5 -/10.2 10 6.8 13.6 50 400
4 42.0 27.0 16.0 37.5 – 15 15.0 7.9 35 140
4.7 42.0 31.0 18.0 37.5 10.2 15 13.0 9.1 35 165
5 42.0 31.0 18.0 37.5 10.2 15 12.5 9.3 35 175
6 42.0 32.0 19.0 37.5 10.2 15 10.4 10.4 35 210
6.8 42.0 32.0 19.0 37.5 10.2 15 9.2 11.1 35 238
7 42.0 38.0 21.0 37.5 10.2 15 9.0 11.9 35 245
8 42.0 38.0 21.0 37.5 10.2 15 8.5 12.2 35 280
9 42.0 38.0 21.0 37.5 10.2 15 8.0 12.6 35 315
10 42.0 43.0 28.0 37.5 10.2 15 7.5 13.2 35 350
12 42.0 43.0 28.0 37.5 10.2 15 7.0 13.7 35 420
14 42.0 45.0 30.0 37.5 10.2/20.3 15 6.8 14.5 35 490
15 42.0 45.0 30.0 37.5 10.2/20.3 15 6.1 15.3 35 525
20 42.0 50.0 36.0 37.5 10.2/20.3 15 5.1 17.9 35 700
18 57.5 45.0 30.0 52.5 20.3 20 8.2 14.6 25 450
20 57.5 45.0 30.0 52.5 20.3 20 7.5 15.2 25 500
22 57.5 50.0 35.0 52.5 20.3 20 7.0 16.9 25 550
25 57.5 50.0 35.0 52.5 20.3 20 6.2 17.9 25 625
26 57.5 50.0 35.0 52.5 20.3 20 6.0 18.2 25 650
30 57.5 55.0 40.0 52.5 20.3 20 5.3 19.9 25 750
35 57.5 55.0 40.0 52.5 20.3 25 4.6 21.4 25 875
40 57.5 55.0 40.0 52.5 20.3 25 4.1 22.7 25 1000
110 59.0 59.0 130.0 52.5 20.3x5 30 3.1 40.0 25 2750
120 59.0 59.0 130.0 52.5 20.3x5 30 2.9 42.0 25 3000

NOTES:
(1)
CAPACITANCE VALUE MEASURED AT 1 kHz. INTERMEDIATE CAPACITANCE VALUES AVAILABLE ON REQUEST.
(2)
NOMINAL DIMENSIONS.
(3)
MAXIMUM tan(δ) VALUES.
(4)
TYPICAL EQUIVALENT SERIES RESISTANCE AT 10 kHz.
(5)
MAXIMUM R.M.S. CURRENT AT 10 kHz, θamb = 70°C FOR Δθcase≤ 20°C.

21
 HIGH DENSITY DC LINK CAPACITORS
TYPE KNG1910, KNG1914

GENERAL CHARACTERISTICS

CAPACITANCE RANGE
UNDC @ 85 °C = 1300 V DC, Uop@ 70 °C = 1550 V DC, Uop@ 105 °C = 900 V DC

CN(1)
Dimensions (mm) (2) tan(δ)@1kHz (3) ESR@10 kHz (4) Imax@10 kHz (5) (dU/dt)max Î
(µF) L H W P P1 (x10-4) (mW) (A) (V/µs) (A)
0.1 32.0 16.0 7.5 27.5 – 10 150.0 1.6 65 7
0.15 32.0 16.0 7.5 27.5 – 10 120.0 1.8 65 10
0.22 32.0 16.0 7.5 27.5 – 10 110.0 1.9 65 14
0.33 32.0 17.0 9.0 27.5 – 10 75.0 2.4 65 21
0.47 32.0 17.0 9.0 27.5 – 10 55.0 2.8 65 31
0.56 32.0 17.0 9.0 27.5 – 10 45.0 3.1 65 36
0.68 32.0 19.0 10.0 27.5 – 10 40.0 3.5 65 44
0.82 32.0 21.0 12.0 27.5 – 10 38.0 3.9 65 53
1 32.0 21.0 12.0 27.5 – 10 30.0 4.3 65 65
1.5 32.0 24.5 15.0 27.5 – 10 20.0 5.9 65 98
2 32.0 26.5 17.0 27.5 – 10 16.0 6.9 65 130
2.2 32.0 26.5 17.0 27.5 – 10 15.0 7.2 65 143
3 32.0 33.0 20.0 27.5 -/10.2 10 12.0 9.0 65 195
3.3 32.0 35.0 20.0 27.5 -/10.2 10 11.0 9.6 65 215
4 32.0 35.5 24.0 27.5 -/10.2 10 10.0 10.6 65 260
5 32.0 40.0 25.0 27.5 -/10.2 10 8.0 12.5 65 325
2 42.0 27.0 16.0 37.5 – 15 22.0 6.5 45 90
3 42.0 31.0 18.0 37.5 10.2 15 15.0 8.5 45 135
4 42.0 32.0 19.0 37.5 10.2 15 11.5 9.9 45 180
5 42.0 38.0 21.0 37.5 10.2 15 9.5 11.5 45 225
6 42.0 43.0 28.0 37.5 10.2 15 8.5 12.2 45 270
7 42.0 43.0 28.0 37.5 10.2 15 8.1 12.7 45 315
8 42.0 43.0 28.0 37.5 10.2 15 7.8 13.0 45 360
9 42.0 43.0 28.0 37.5 10.2 15 7.5 13.2 45 405
10 42.0 45.0 30.0 37.5 10.2/20.3 15 7.0 14.3 45 450
12 42.0 50.0 36.0 37.5 10.2/20.3 15 6.4 16.0 45 540
14 42.0 50.0 36.0 37.5 10.2/20.3 15 5.8 16.8 45 630
14 57.5 45.0 30.0 52.5 20.3 20 9.0 13.9 30 420
15 57.5 45.0 30.0 52.5 20.3 20 8.5 14.3 30 450
18 57.5 50.0 35.0 52.5 20.3 20 7.2 16.6 30 540
20 57.5 55.0 40.0 52.5 20.3 20 6.6 17.9 30 600
22 57.5 55.0 40.0 52.5 20.3 20 6.2 18.4 30 660
25 57.5 55.0 40.0 52.5 20.3 20 5.5 19.6 30 750
70 59.0 59.0 130.0 52.5 20.3x5 30 4.0 35.0 30 2100
90 59.0 59.0 130.0 52.5 20.3x5 30 3.2 40.0 30 2700

NOTES:
(1)
CAPACITANCE VALUE MEASURED AT 1 kHz. INTERMEDIATE CAPACITANCE VALUES AVAILABLE ON REQUEST.
(2)
NOMINAL DIMENSIONS.
(3)
MAXIMUM tan(δ) VALUES.
(4)
TYPICAL EQUIVALENT SERIES RESISTANCE AT 10 kHz.
(5)
MAXIMUM R.M.S. CURRENT AT 10 kHz, θamb = 70°C FOR Δθcase≤ 20°C.

22
 HIGH DENSITY DC LINK CAPACITORS
APPLICATIONS

FREQUENCY INVERTERS

DC/AC
INVERTER
DC/AC
inverter

SOLAR POWER PLANTS

DC (AC)/AC (DC)
INVERTER
DC (AC)/AC (DC)
INVERTER
WELDING EQUIPMENT
DC (AC)/AC (DC)
INVERTER

HYBRID VEHICLES

DIMENSIONS UPS SYSTEMS

KNG1910 (2 pins) KNG1914 (4 pins)

L W L W
H
H

4 or 6
4 or 6

P d P d
P1

KNG1914 (12 pins)

L W
H

P d P1 P1 P1 P1 P1

TERMINAL DIMENSIONS MAX. BOX DIMENSIONS

P TOLERANCE P1 TOLERANCE d TOLERANCE Lmax Hmax Wmax
(mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm)
27.5 ±0.5 – – 0.8 ±0.05 L + 0.5 H + 0.2 W + 0.5
27.5 ±0.5 10.2 ±0.5 1 OR 1.2 ±0.05 L + 0.5 H + 0.2 W + 0.5
37.5 ±0.5 10.2 ±0.5 1 OR 1.2 ±0.05 L + 0.5 H + 0.5 W + 0.5
37.5 ±0.5 20.3 ±0.5 1 OR 1.2 ±0.05 L + 0.5 H + 0.5 W + 0.5
52.5 ±0.5 20.3 ±0.5 1.2 ±0.05 L + 1.0 H + 1.0 W + 1.0

23
 HIGH DENSITY DC LINK CAPACITORS
CONSTRUCTION, CAUTIONS AND WARNINGS

CONSTRUCTION

DIELECTRIC: POLYPROPYLENE FILM

CAPACITOR ELECTRODES: VACUUM-DEPOSITED
CASING: PLASTIC CASE WITH FLAME-RETARDANT EPOXY RESIN SEALING (UL 94 V-0)
TERMINAL: PARALLEL TINNED COPPER (2, 4 OR 12 PINS)

INTERNAL CONSTRUCTION

FIRST CONTACT LAYER

SECOND CONTACT LAYER

POLYPROPYLENE FILM DIELECTRIC METALLIZED LAYER

METAL-SPRAYED CONTACT LAYERS

CAUTIONS AND WARNINGS

MECHANICAL OVERLOADS

ATTENTION: THE CAPACITOR IS DESIGNED FOR MOUNTING ON A PC BOARD. DO NOT MOVE THE CAPACITOR, AFTER IT HAS BEEN SOLDERED TO
THE PC BOARD.THE CAPACITOR SHOULD NOT BE MOUNTED ON PLACES WHERE VIBRATIONS OR ACCELERATIONS OCCUR. DO NOT EXCEED THE
TESTED ABILITY TO WITHSTAND VIBRATION. AVOID ANY COMPRESSIVE, TENSILE OR FLEXURAL STRESS.

NOTE: MOVEMENT OF THE CAPACITOR WITHIN THE CASE CAN CAUSE LOW INSULATION RESISTANCE, SHORTS, FAILURE ON TERMINALS AND THE CAPACITOR CASE.

OVERLOAD

ATTENTION: DO NOT OVERLOAD THE CAPACITOR. AVOID OVERLOADING THE CAPACITOR AND CONSIDER THE FLAMMABILITY OF MATERIALS.

IMPULSES

ATTENTION: IF ELECTRIC ENERGY IMPULSES ARE HIGHER, DIELECTRIC WILL BREAK DOWN. AVOID EXTERNAL ELECTRIC ENERGY IMPULSE.
THE PEAK VOLTAGE (UP, AC) SHOULD NOT BE HIGHER THAN THE RATED DC VOLTAGE (UNDC).

ENVIRONMENTAL CONDITIONS

ATTENTION: DO NOT EXCEED OPERATING TEMPERATURE. DO NOT EXPOSE THE CAPACITOR TO HUMIDITY LONGER THAN IT IS RECOMMENDED.
DO NOT EXPOSE THE CAPACITOR TO INCREASED TEMPERATURE MORE THAN IT IS RECOMMENDED. THE DISSIPATION FACTOR MAY GO UP AND
DOWN WITH INCREASED TEMPERATURE. AVOID EXTERNAL FIRE OR ELECTRICITY.

24
 DC LINK CAPACITORS
TYPE DC LINK EV - CUSTOMIZED PRODUCTS

APPLICATIONS
ENERGY CONVERSION
AC MOTOR DRIVES
HYBRID/ELECTRIC VEHICLES
INVERTER MODULES

FEATURES

METALLIZED SELF-HEALING POLYPROPYLEN

LOW ESR (HIGH RIPPLE CURRENT)
LOW ESL
LONG LIFETIME

SPECIFICATIONS REFERENCE STANDARD

ELECTRICAL CHARACTERISTICS
IEC 61071
RATED CAPACITANCE 500 µF, ± 10 %
RATED DC VOLTAGE 450 V DC
PEAK VOLTAGE 675 V AC
NOM. RMS CURRENT (@ Tamb = MAX. 80 °C ) 85 Arms
MAX. RMS CURRENT (@ Tamb = MAX. 70 °C ) 120 Arms
MAX. PEAK CURRENT 2500 A
EQUIVALENT SERIES RESISTANCE @ 1 kHz < 1 mW
EQUIVALENT SERIES INDUCTANCE 15 nH
MAX. PULSE RISE TIME 4 V/µs
THERMAL CHARACTERISTICS
MIN. OPERATING TEMPERATURE -40 °C
MAX. OPERATING TEMPERATURE +110 °C
STORAGE TEMPERATURE -40 °C to +85 °C
TEST METHODS & PERFORMANCES
VOLTAGE TEST BETWEEN TERMINALS @ 25 °C 675 V/10 s
VOLTAGE TEST TERMINALS TO CASE @ 50 Hz 2500 V/1 min
LIFE EXPENTANCY
LIFE EXPENTANCY @ UNDC 15 000 HOURS (HOTSPOT MAX. TEMPERATURE 90 °C)
RELIABILITY 300 FIT
CONSTRUCTION
DIELECTRIC METALLIZED POLYPROPYLENE
WINDING NON-INDUCTIVE
FILLING POLYURETHANE RESIN
CASE CONSTRUCTIONS PBT (METALLIC FOR PROTOTYPE)
TERMINALS FLAT COPPER
DIMENSIONS
WIDTH 72 mm
HEIGHT 50 mm
LENGHT 237 mm
APP. WEIGHT < 1.5 kg

25
 DC LINK CAPACITORS
TYPE DC LINK EV - CUSTOMIZED PRODUCTS

DIMENSIONS

DRAWING

237 ±1
14 14

+ -

52.5 ±1
+ - + - + -

31.65 12 9

98.75

165.85

171.85 30.15
104.75 21
37.65 21

15 ±1
6 R 6.50 14
23.65
6
7

R 4.70 M6
13 16

87 ±1
18 ±1

4
R
30°

R5
50 ±1
1
33.50

72 ±1

NOTES:

FOR MORE INFORMATION ABOUT THE CONSTRUCTION, PLEASE CONTACT ISKRA.

ISKRA TECHNICAL DEPARTMENT IS READY TO SUPPORT CUSTOMERS IN DEVELOPING CAPACITORS ON THEIR REQUESTS AND SPECIFICATIONS.

26
 SNUBBER CAPACITORS
TYPE KNO19Ax, KNO19Bx, KNO1910, KNO1914

APPLICATIONS

SNUBBER CAPACITORS ARE USED IN

APPLICATIONS WITH HIGH PULSE LOADINGS AND
HIGH FREQUENCIES. THE PURPOSE OF SNUBBER
CAPACITORS IS TO ELIMINATE VOLTAGE SPIKES WHICH
ARE CAUSED BY SEMICONDUCTORS OR OTHER
DEVICES.

IGBT (INSULATED GATE BIPOLAR TRANSISTOR)

MODULE
AC AND DC CONVERTER AND INVERTER (ELECTRIC
DRIVES)
UNINTERRUPTIBLE POWER SYSTEM (UPS)
POWER SUPPLY

FEATURES REFERENCE STANDARD

HIGH VOLTAGE IEC 61071

HIGH PULSE LOAD CAPABILITY
SELF-HEALING PROPERTIES
HIGH RELIABILTY
LOW SELF-INDUCTANCE
LOW DISSIPATION FACTOR OF DIELECTRIC
TERMINAL OPTIONS FOR DIRECT MOUNT OR BOARD
HIGH INSULATION RESISTANCE

SPECIFICATIONS

RATED CAPACITANCE 0.047 µF up to 8 µF

CAPACITANCE TOLERANCE ± 5 %, ± 10 %
RATED VOLTAGE 630 V DC, 850 V DC, 1000 V DC, 1200 V DC,
1600 V DC, 2000 V DC, 2500 V DC, 3000 V DC
OPERATING TEMPERATURE RANGE -40 °C TO +85 °C
CLIMATIC CATEGORY 40/85/56 ACCORDING TO IEC 60068-1
MAXIMUM APPLICATION TEMPERATURE +85 °C
DISSIPATION FACTORS AT 1 kHz tgd ≤ 5 x 10-4
TEST VOLTAGE TERMINAL TO TERMINAL 1.5 x UNDC , 10 s
PEAK NON-REPETITIVE MAX. CURRENT Î x 1.5
LIFE EXPECTANCY ≥100 000 HOURS AT UNDC , θhs = 70 °C

27
 SNUBBER CAPACITORS
TYPE KNO19Ax, KNO19Bx, KNO1910, KNO1914

GENERAL CHARACTERISTICS

TYPE KNO19Ax, KNO19Bx, KNO1910, KNO1914

CN UNDC Urms (dU/dt)max DIMENSIONS CN UNDC Urms (dU/dt)max DIMENSIONS

(µF) (V DC) (V AC) (V/µs) (mm) LxHxW (µF) (V DC) (V AC) (V/µs) (mm) LxHxW
0.33 630 400 600 32 x 20 x 11 0.22 850 500 600 32 x 20 x 11
0.39 630 400 600 32 x 24.5 x 15 0.27 850 500 600 32 x 24.5 x 15
0.47 630 400 600 32 x 24.5 x 15 0.33 850 500 600 32 x 24.5 x 15
0.56 630 400 600 41.5 x 23 x 14 0.39 850 500 600 41.5 x 23 x 14
0.68 630 400 600 41.5 x 23 x 14 0.47 850 500 600 41.5 x 23 x 14
1 630 400 500 41.5 x 27 x 16 0.56 850 500 600 41.5 x 27 x 16
1.2 630 400 500 41.5 x 31 x 18 0.68 850 500 600 41.5 x 27 x 16
1.5 630 400 500 41.5 x 31 x 18 0.82 850 500 600 41.5 x 31 x 18
2 630 400 500 41.5 x 38 x 21 1 850 500 600 41.5 x 31 x 18
2.2 630 400 500 41.5 x 38 x 21 1.2 850 500 500 41.5 x 38 x 21
2.5 630 400 400 41.5 x 43 x 28 1.5 850 500 500 41.5 x 38 x 21
2.7 630 400 400 41.5 x 43 x 28 1.8 850 500 500 41.5 x 43 x 28
3 630 400 400 41.5 x 43 x 28 2 850 500 500 41.5 x 43 x 28
3.3 630 400 400 41.5 x 43 x 28 2.2 850 500 500 42 x 45 x 30
3.5 630 400 400 41.5 x 43 x 28 2.5 850 500 500 42 x 45 x 30
4 630 400 300 42 x 45 x 30 2.7 850 500 400 42 x 45 x 30
4.7 630 400 300 57.5 x 45 x 30 3 850 500 400 57.5 x 45 x 30
5 630 400 300 57.5 x 45 x 30 3.3 850 500 400 57.5 x 45 x 30
5.6 630 400 300 57.5 x 45 x 30 4 850 500 400 57.5 x 45 x 30
6 630 400 300 57.5 x 45 x 30 4.7 850 500 400 57.5 x 50 x 35
6.3 630 400 300 57.5 x 50 x 35 5.6 850 500 300 57.5 x 50 x 35
7 630 400 100 57.5 x 50 x 35
8 630 400 100 57.5 x 50 x 35

CN UNDC Urms (dU/dt)max DIMENSIONS CN UNDC Urms (dU/dt)max DIMENSIONS

(µF) (V DC) (V AC) (V/µs) (mm) LxHxW (µF) (V DC) (V AC) (V/µs) (mm) LxHxW
0.22 1000 600 1000 32 x 24.5 x 15 0.15 1200 630 800 32 x 20 x 11
0.27 1000 600 1000 32 x 24.5 x 15 0.22 1200 630 800 41.5 x 23 x 14
0.33 1000 600 900 32 x 24.5 x 15 0.27 1200 630 800 41.5 x 23 x 14
0.33 1000 600 900 41.5 x 23 x 14 0.33 1200 630 700 41.5 x 27 x 16
0.39 1000 600 900 41.5 x 23 x 14 0.39 1200 630 700 41.5 x 27 x 16
0.47 1000 600 900 41.5 x 27 x 16 0.47 1200 630 700 41.5 x 31 x 18
0.56 1000 600 900 41.5 x 27 x 16 0.56 1200 630 700 41.5 x 32 x 19
0.68 1000 600 900 41.5 x 31 x 18 0.68 1200 630 700 41.5 x 38 x 21
0.82 1000 600 500 41.5 x 32 x 19 0.82 1200 630 700 41.5 x 38 x 21
1 1000 600 500 41.5 x 38 x 21 1 1200 630 500 41.5 x 43 x 28
1.2 1000 600 400 41.5 x 38 x 21 1.2 1200 630 500 41.5 x 43 x 28
1.5 1000 600 400 41.5 x 43 x 28 1.5 1200 630 500 42 x 45 x 30
1.8 1000 600 400 42 x 45 x 30 1.8 1200 630 500 43 x 48 x 33
2 1000 600 400 42 x 45 x 30 2 1200 630 500 57.5 x 45 x 30
2.2 1000 600 400 42 x 45 x 30 2.2 1200 630 500 57.5 x 45 x 30
2.5 1000 600 400 57.5 x 45 x 30 2.5 1200 630 500 57.5 x 50 x 35
2.7 1000 600 400 43 x 48 x 33 2.7 1200 630 500 57.5 x 50 x 35
2.7 1000 600 400 57.5 x 45 x 30 3 1200 630 500 57.5 x 50 x 35
3 1000 600 400 57.5 x 45 x 30 3.3 1200 630 500 57.5 x 50 x 35
3.3 1000 600 400 57.5 x 50 x 35
4 1000 600 300 57.5 x 50 x 35

28
 SNUBBER CAPACITORS
TYPE KNO19Ax, KNO19Bx, KNO1910, KNO1914

GENERAL CHARACTERISTICS

TYPE KNO19Ax, KNO19Bx, KNO1910, KNO1914

CN UNDC Urms (dU/dt)max DIMENSIONS CN UNDC Urms (dU/dt)max DIMENSIONS

(µF) (V DC) (V AC) (V/µs) (mm) LxHxW (µF) (V DC) (V AC) (V/µs) (mm) LxHxW
0.1 1600 650 900 32 x 20 x 11 0.1 2000 700 1000 32 x 24.5 x 15
0.12 1600 650 900 32 x 24.5 x 15 0.1 2000 700 1000 41.5 x 23 x 14
0.15 1600 650 900 41.5 x 23 x 14 0.12 2000 700 1000 41.5 x 23 x 14
0.22 1600 650 900 41.5 x 23 x 14 0.15 2000 700 1000 41.5 x 23 x 14
0.27 1600 650 700 41.5 x 27 x 16 0.22 2000 700 900 41.5 x 27 x 16
0.33 1600 650 700 41.5 x 27 x 16 0.27 2000 700 900 41.5 x 31 x 18
0.39 1600 650 700 41.5 x 31 x 18 0.33 2000 700 900 41.5 x 32 x 19
0.47 1600 650 700 41.5 x 32 x 19 0.39 2000 700 900 41.5 x 38 x 21
0.56 1600 650 700 41.5 x 38 x 21 0.47 2000 700 900 41.5 x 38 x 21
0.68 1600 650 700 41.5 x 38 x 21 0.56 2000 700 900 41.5 x 43 x 28
0.75 1600 650 700 41.5 x 43 x 28 0.68 2000 700 900 41.5 x 43 x 28
0.82 1600 650 700 41.5 x 43 x 28 0.82 2000 700 600 42 x 45 x 30
1 1600 650 700 41.5 x 43 x 28 1 2000 700 700 42 x 45 x 35
1.2 1600 650 700 57.5 x 45 x 30 1 2000 700 600 57.5 x 45 x 30
1.5 1600 650 700 57.5 x 45 x 30 1.2 2000 700 600 57.5 x 45 x 30
2 1600 650 500 57.5 x 50 x 35 1.5 2000 700 600 57.5 x 50 x 35
2.2 1600 650 500 57.5 x 50 x 35
2.5 1600 650 400 57.5 x 50 x 35
3 1600 650 400 57.5 x 55 x 40

CN UNDC Urms (dU/dt)max DIMENSIONS CN UNDC Urms (dU/dt)max DIMENSIONS

(µF) (V DC) (V AC) (V/µs) (mm) LxHxW (µF) (V DC) (V AC) (V/µs) (mm) LxHxW
0.1 2500 725 1100 41.5 x 27 x 16 0.047 3000 750 1600 41.5 x 23x 14
0.15 2500 725 1100 41.5 x 31 x 18 0.068 3000 750 1600 41.5 x 27 x 16
0.22 2500 725 1100 41.5 x 38 x 21 0.1 3000 750 1600 41.5 x 27 x 16
0.33 2500 725 1100 41.5 x 43 x 28 0.15 3000 750 1600 41.5 x 32 x 19
0.47 2500 725 1100 42 x 45 x 30 0.22 3000 750 1600 41.5 x 38 x 21
0.56 2500 725 1000 57.5 x 45 x 30 0.33 3000 750 1400 42 x 45 x 30
0.68 2500 725 1000 57.5 x 45 x 30 0.47 3000 750 1400 57.5 x 45 x 30
0.82 2500 725 1000 57.5 x 45 x 30 0.68 3000 750 1200 57.5 x 50 x 35
1 2500 725 900 57.5 x 50 x 35 0.82 3000 750 900 57.5 x 50 x 35
1.2 2500 725 900 57.5 x 55 x 40 1 3000 750 900 57.5 x 55 x 40

POSSIBLE LUG VERSION DEPENDING ON BOX SIZE

TYPE KNO19xx (DIGIT 6-7)

DIMENSIONS WIRE LUGS FOR VERTICAL MOUNTING LUGS FOR HORIZONTAL MOUNTING
(LxHxW) 10 14 A0 A1 A2 A3 A4 B0 B1 B2 B3 B4 B5
32 x 20 x 11
32 x 24.5 x 15
41.5 x 23 x 14
41.5 x 27 x 16
41.5 x 31 x 18
41.5 x 32 x 19
41.5 x 38 x 21
41.5 x 43 x 28
42 x 45 x 30
42 x 45 x 35
43 x 48 x 33
57.5 x 45 x 30
57.5 x 50 x 35
57.5 x 55 x 40

29
 SNUBBER CAPACITORS
DIMENSIONS

KNO19A0, KNO19A1, KNO19A4 KNO19B0, KNO19B1, KNO19B3, KNO19B5

P 1
13.7

0.8 0.05
9 0.2 0.8 0.05

max.15
H
6 1

6.1 0.1
max.9
P1 1

H
L W

P 1
13.7 9 0.2
L W
max.15

6.1 0.1

P1 1
max.9

KNO19A2 KNO19B2

P 1
14.7
max. 2.5

0.8 0.05

10.2 0.2 0.8 0.05

max.19
H

8.2 0.1
6 1
max.12

P1 1
L W

H
max. 10

8.2 0.1

P1 1
L W
max. 17.5

14.7 10.2 0.2

P 1

KNO19A3 KNO19B4

P 1
18
0.8 0.05

10.2 0.2
max.2.5

0.8 0.05
H

max.19

8.2 0.1

6 1
W
max.12

L
P1 1
P 1
H

P1 1
19 13 0.2

L W
max.15

6.1 0.1
max. 9.5

LUG DIMENSIONS

L P P1 L P P1
VERSION SCREW VERSION SCREW
(mm) (mm) (mm) (mm) (mm) (mm)
A0 41.5 24 10 M6 B0 41.5 24 10 M6
A0 42 24 10 M6 B0 42 24 10 M6
A0 43 24 10 M6 B0 43 24 10 M6
A0 57.5 37 23 M6 B0 57.5 37 23 M6
A1 57.5 25 11 M6 B1 57.5 25 11 M6
A2 57.5 46 31 M8 B2 57.5 37 23 M8
A3 41.5 37 18 M6 B3 57.5 22 8 M6
A4 41.5 22 8 M6 B4 41.5 37 18 M8
B5 41.5 22 8 M6

30
 SNUBBER CAPACITORS
DIMENSIONS AND CONSTRUCTION

KNO1910 (2 PINS) KNO1914 (4 PINS)

Lmax. Wmax. L W

Hmax.

H
4 or 6
4 or 6

P±0.4 d P±0.4 d
P1±0.5

L P TOLERANCE P1 TOLERANCE d TOLERANCE

VERSION
(mm) (mm) (mm) (mm) (mm) (mm) (mm)
32 27.5 ±0.4 / / 0.8 ±0.5
41.5 37.5 ±0.4 / ±0.5 1 or 1.2 ±0.5
10
42 37.5 ±0.4 / ±0.5 1 or 1.2 ±0.5
57.5 50.5 ±0.4 / ±0.5 1.2 ±0.5
41.5 37.5 ±0.4 10.2 or 20.3 ±0.5 1 or 1.2 ±0.5
14 42 37.5 ±0.4 10.2 or 20.3 ±0.5 1 or 1.2 ±0.5
57.5 50.5 ±0.4 20.3 ±0.5 1.2 ±0.5

CONSTRUCTION

DIELECTRIC: POLYPROPYLENE FILM

CAPACITOR ELECTRODES: VACUUM-DEPOSITED : METAL LAYERS
CASING: PLASTIC CASE WITH FLAME-RETARDANT EPOXY RESIN SEALING (UL 94 V -0)
TERMINALS: TINNED LUGS FROM BRASS, COPPER OR PARALLEL TINNED COPPER WIRE WITH 2 OR 4 EXECUTIONS

DOUBLE SIDED METALLIZED PLASTIC

FILM WITH INTERNAL SERIES
CONNECTION AND METALLIZED
PLASTIC FILM

31
 SNUBBER CAPACITORS
APPLICATIONS

WIND PLANTS
FREQUENCY INVERTERS

DC/AC
INVERTER
DC/AC
INVERTER

SOLAR POWER PLANTS

DC (AC)/AC (DC)
INVERTER
DC (AC)/AC (DC)
INVERTER
WELDING EQUIPMENT
DC (AC)/AC (DC)
INVERTER

IGBT MODULE
HYBRID VEHICLES

UPS SYSTEMS

32
 SNUBBER CAPACITORS
CAUTIONS AND WARNINGS

CAUTIONS AND WARNINGS

MECHANICAL OVERLOADS

ATTENTION: THE CAPACITOR IS DESIGNED FOR MOUNTING ON A PC BOARD. DO NOT MOVE THE CAPACITOR, AFTER IT HAS BEEN SOLDERED TO
THE PC BOARD. THE CAPACITOR SHOULD NOT BE MOUNTED ON PLACES WHERE VIBRATIONS OR ACCELERATIONS OCCUR. DO NOT EXCEED THE
TESTED ABILITY TO WITHSTAND VIBRATION. AVOID ANY COMPRESSIVE, TENSILE OR FLEXURAL STRESS. WHEN FIXING THE LUGS THE SCREW
TORQUE IS TO BE LIMITED TO MAX. 10 Nm.

OVERLOAD

ATTENTION: DO NOT OVERLOAD THE CAPACITOR. AVOID OVERLOADING THE CAPACITOR AND CONSIDER THE FLAMMABILITY OF MATERIALS.

IMPULSES

ATTENTION: IF ELECTRIC ENERGY IMPULSES ARE HIGHER, DIELECTRIC WILL BREAK DOWN. AVOID EXTERNAL ELECTRIC ENERGY IMPULSE.
THE PEAK VOLTAGE (UP, AC) SHOULD NOT BE HIGHER THAN THE RATED DC VOLTAGE (UNDC).

ENVIRONMENTAL CONDITIONS

ATTENTION: DO NOT EXCEED OPERATING TEMPERATURE. DO NOT EXPOSE THE CAPACITOR TO HUMIDITY LONGER THAN IT IS RECOMMENDED.
DO NOT EXPOSE THE CAPACITOR TO INCREASED TEMPERATURE MORE THAN IT IS RECOMMENDED. THE DISSIPATION FACTOR MAY GO UP AND
DOWN WITH INCREASED TEMPERATURE. AVOID EXTERNAL FIRE OR ELECTRICITY.

33
 AC/DC GENERALS PURPOSE CAPACITORS
TYPE KNI5048

APPLICATIONS

METALLIZED POLYPROPYLENE AC AND DC CAPACITORS ARE

USED FOR POWER ELECTRONIC APPLICATIONS WITH HIGH
CURRENT AND HARMONICS DISTORTION WITH LONG LIFE
EXPECTANCY.
INVERTER
FILTERING
SWITCHING

FEATURES REFERENCE STANDARD

AC/DC VOLTAGE IEC 61071

SELF-HEALING PROPERTIES UL-CSA APPROVED (FILE No. E163120)
PROTECTED, 10 000 AFC
HIGH RELIABILTY
CYLINDRICAL ALUMINIUM CASE WITH PLASTIC SELF-
EXTINGUISHING SEALING COVER
OVERPRESSURE DISCONNECTOR
TINNED BRASS SCREW

SPECIFICATIONS

RATED CAPACITANCE 10 µF - 600 µF

CAPACITANCE TOLERANCE ± 5 %, ± 10 %
RATED VOLTAGE (Urms) 250 V AC, 330 V AC, 480 V AC, 690 V AC
OPERATING TEMPERATURE RANGE -40 °C to +85 °C
CLIMATIC CATEGORY 40/070/56 ACCORDING TO IEC 60068-1
DISSIPATION FACTORS AT 1 kHz tgd ≤ 10 x 10-4 AT 100 Hz
TEST VOLTAGE TERMINAL TO TERMINAL 1.5 x UN , 10 s
TEST VOLTAGE (TERMINAL TO CASE) 3 kV, 50 Hz, 2 s
LIFE EXPECTANCY 100 000 HOURSAT Urms , θhs = 70 °C
FAILURE RATE 300 FIT

CONSTRUCTION

DIELECTRIC: POLYPROPYLENE FILM

CAPACITOR ELECTRODES: VACUUM-DEPOSITED : METAL LAYERS
CASING: CYLINDRICAL ALUMINIUM CASE WITH PLASTIC SELF-EXTINGUISHING SEALING
COVER
TINNED BRASS SCREW

34
 AC/DC GENERALS PURPOSE CAPACITORS
TYPE KNI5048

INTERNAL CONSTRUCTION

FIRST CONTACT LAYER

SECOND CONTACT LAYER

POLYPROPYLENE FILM DIELECTRIC METALLIZED LAYER

METAL-SPRAYED CONTACT LAYERS

TERMINATIONS

KNI5048 D50 TO D75 mm KNI5048 D85 mm

P 1 P 1
M M
H1 2

H1 2
H 5
H 2

M1
L

M1
L

D 1
D 1

35
 AC/DC GENERALS PURPOSE CAPACITORS
TYPE KNI5048

GENERAL CHARACTERISTICS

CAPACITANCE RANGE
Urms = 250 V AC, UN = 353 V AC, UNDC = 400 V DC

CN Imax Î dU/dt Rs Rth DxH H1 M P M1 L

(µF) (A) (kA) (V/µs) (mW) (KW) (mm) (mm) (mm) (mm) (mm) (mm) Urms = 250 V AC

30 22 0.75 25 5.1 11.0 50 x 80 24 6 22 12 12

40 22 1 25 5.1 11.0 50 x 80 24 6 22 12 12
50 22 1.25 25 4.9 9.7 50 x 93 24 6 22 12 12
60 25 1.5 25 4.7 8.7 60 x 80 24 6 22 12 12
70 25 1.75 25 4.7 8.7 60 x 80 24 6 22 12 12
80 25 2 25 4.2 7.8 60 x 93 24 6 22 12 12
100 25 2.5 25 3.6 7.1 60 x 105 24 6 22 12 12
130 25 1.95 15 3.9 6.0 60 x 130 24 6 22 12 12
150 25 2.25 15 3.9 6.0 60 x 130 24 6 22 12 12
150 35 2.25 15 3.6 5.2 75 x 110 28 10 34 12 16
175 25 2.62 15 4.0 5.2 60 x 155 24 6 22 12 12
200 25 3 15 4.0 5.2 60 x 155 24 6 22 12 12
200 35 3 15 3.5 4.4 75 x 135 28 10 34 12 16
250 40 3 12 3.8 3.9 75 x 160 28 10 34 12 16
300 50 3.6 12 3.8 3.9 75 x 160 28 10 34 12 16
400 50 4.8 12 3.0 2.8 85 x 200 34 10 35 12 16
500 50 5 10 2.7 2.3 85 x 250 34 10 35 12 16
600 50 6 10 2.4 2.3 85 x 250 34 10 35 12 16

CAPACITANCE RANGE
Urms = 330 V AC, UN = 465 V AC, UNDC = 600 V DC

CN Imax Î dU/dt Rs Rth DxH H1 M P M1 L

(µF) (A) (kA) (V/µs) (mW) (KW) (mm) (mm) (mm) (mm) (mm) (mm) Urms = 340 V AC

25 22 0.75 30 5.3 11.0 50 x 80 24 6 22 12 12

30 22 0.9 30 5.3 11.0 50 x 80 24 6 22 12 12
40 22 1.2 30 5.1 9.7 50 x 93 24 6 22 12 12
50 22 1.25 25 5.0 8.7 55 x 93 24 6 22 12 12
60 25 1.5 25 4.8 7.1 60 x 105 24 6 22 12 12
70 25 1.4 20 4.8 7.1 60 x 105 24 6 22 12 12
75 25 1.5 20 4.6 7.1 60 x 105 24 6 22 12 12
80 25 1.6 20 4.6 7.1 60 x 105 24 6 22 12 12
100 25 2 20 4.1 6.0 60 x 130 24 6 22 12 12
100 30 1.5 15 3.8 5.2 75 x 110 28 10 34 12 16
150 30 2.25 15 3.5 4.4 75 x 135 28 10 34 12 16
200 40 3 15 2.9 4.0 75 x 155 28 10 34 12 16
250 45 3.75 15 3.0 2.8 85 x 200 34 10 35 12 16
300 50 4.5 15 3.0 2.8 85 x 200 34 10 35 12 16
400 50 4.8 12 2.6 2.3 85 x 250 34 10 35 12 16

APPROVALS IN USE
NOTES: OTHER VALUES AND DIMENSIONS AVAILABLE ON REQUEST.

36
 AC/DC GENERALS PURPOSE CAPACITORS
TYPE KNI5048

GENERAL CHARACTERISTICS

CAPACITANCE RANGE
Urms = 480 V AC, UN = 677 V AC, UNDC = 850 V DC

CN Imax Î dU/dt Rs Rth DxH H1 M P M1 L

(µF) (A) (kA) (V/µs) (mW) (KW) (mm) (mm) (mm) (mm) (mm) (mm) Urms = 500 V AC

10 22 0.4 40 5.5 11.0 50 x 80 24 6 22 12 12

15 22 0.6 40 5.5 9.7 55 x 80 24 6 22 12 12
20 25 0.8 40 5.3 8.7 60 x 80 24 6 22 12 12
25 25 1 40 5.2 7.8 60 x 93 24 6 22 12 12
30 25 1.2 40 4.8 7.1 60 x 105 24 6 22 12 12
35 25 1.4 40 4.8 7.1 60 x 105 24 6 22 12 12
40 25 1.6 40 4.1 6.0 60 x 130 24 6 22 12 12
50 25 2 40 4.0 6.0 60 x 130 24 6 22 12 12
60 30 2.1 35 3.8 4.4 75 x 135 28 10 34 12 16
70 30 2.1 30 3.8 4.4 75 x 135 28 10 34 12 16
80 35 2 25 4.9 3.9 75 x 160 28 10 34 12 16
90 35 2.25 25 4.7 3.9 75 x 160 28 10 34 12 16
100 30 2 20 5.1 3.3 75 x 195 28 10 34 12 16
100 35 2.5 25 2.6 3.1 85 x 175 34 10 35 12 16
133 35 2.66 20 3.5 2.8 85 x 200 34 10 35 12 16
150 50 3 20 3.4 2.8 85 x 200 34 10 35 12 16
200 50 4 20 3.0 2.3 85 x 250 34 10 35 12 16
250 50 3.75 15 2.6 2.0 85 x 300 34 10 35 12 16

CAPACITANCE RANGE
Urms = 690 V AC, UN = 973 V AC, UNDC = 1200 V DC

CN Imax Î dU/dt Rs Rth DxH H1 M P M1 L

(µF) (A) (kA) (V/µs) (mW) (KW) (mm) (mm) (mm) (mm) (mm) (mm) Urms = 690 V AC

10 25 0.4 40 4.8 8.7 60 x 80 24 6 22 12 12

15 22 0.45 30 4.5 7.1 60 x 105 24 6 22 12 12
22 25 0.66 30 4 6.0 60 x 130 24 6 22 12 12
33 35 0.82 25 4.2 4.2 85 x 120 34 10 35 12 16
47 50 1.17 25 2.9 3.6 85 x 145 34 10 35 12 16
68 65 1.7 25 3.2 3.2 85 x 170 34 10 35 12 16

APPROVALS IN USE
NOTES: OTHER VALUES AND DIMENSIONS AVAILABLE ON REQUEST.

37
 AC/DC GENERALS PURPOSE CAPACITORS
APPLICATIONS

WIND PLANTS
FREQUENCY INVERTERS

DC/AC
INVERTER
DC/AC
INVERTER

SOLAR POWER PLANTS

DC (AC)/AC (DC)
INVERTER

WELDING EQUIPMENT

DC (AC)/AC (DC)
INVERTER

UPS SYSTEMS

38
 AC/DC GENERALS PURPOSE CAPACITORS
CONNECTION AND MOUNTING INSTRUCTIONS

SAFE OPERATION OF THE CAPACITORS CAN BE EXPECTED ONLY IF ALL ELECTRICAL AND THERMAL SPECIFICATIONS AS STATED ON THE LABEL, IN
THE DATA SHEETS OR CATALOGUES AND THE FOLLOWING INSTRUCTIONS ARE STRICTLY OBSERVED. THE MANUFACTURER DOES NOT ACCEPT
RESPONSIBILITY FOR ANY DAMAGE THAT COULD ARISE DUE TO NON-OBSERVANCE.

CONNECTION

USE THE APPROPRIATE TAB CONNECTORS TO CONNECT THE CABLES OF THE CAPACITORS.

DO NOT SOLDER LEADS TO THE TERMINALS.

DO NOT BEND OR TURN OR MOVE IN ANY OTHER WAY THE CONNECTING TERMINALS AND THE TAB CONNECTORS.

DO NOT USE HEAVY OR SHARP OBJECTS AND TOOLS ON THE BORDERING OR THE CONNECTING TERMINALS.

CONNECTION AT THREADED STUDS SHOULD BE MADE BETWEEN TWO NUTS. DURING THE CONNECTION THE LOWER NUT SHOULD BE BACKED UP
TO AVOID ANY TRANSMISSION OF THE TORQUE.

PERMITTED TORQUE FOR SCREW CONNECTIONS:

M6 - 5 Nm WARNING: SAFE CONNECTION

M8 - 6 Nm

M10 - 10 Nm

TO PREVENT BREAKING AT TIGHTENING

ALWAYS USE TWO WRENCHES

MOUNTING

CAN BE MOUNTED IN ANY POSITION.

THE CAPACITOR HAS TO BE INSTALLED IN SUCH A WAY AS TO AVOID ANY MECHANICAL DAMAGE AND DENTS IN THE ALUMINIUM.

CAPACITORS WITH OVERPRESSURE SAFETY DEVICE SHOULD BE CONNECTED WITH SUFFICIENTLY FLEXIBLE LEADS IN ORDER TO ENABLE PROPER
FUNCTIONING OF THE MECHANISM. ABOVE THE TERMINALS LEAVE ENOUGH SPACE FOR EXPANSION OF THE CAPACITOR CASE.

LEAVE A MINIMUM DISTANCE OF 15 MM OF FREE SPACE ABOVE EACH CAPACITOR.

CONNECT THESE CAPACITORS BY USING ONLY FLEXIBLE CABLES OR ELASTIC COPPER BANDS.

EARTHING

CAPACITORS WITH A METAL CASE MUST BE EARTHED AT THE MOUNTING STUD.

PERMITTED TORQUE FOR STUDS:

M8 – 5 Nm

M12 – 12 Nm

39
 AC/DC GENERALS PURPOSE CAPACITORS
LIFETIME EXPECTANCY

EXPECTED LIFETIME CURVES

1000000

100000 HOT SPOT

TEMPERATURE
EXPECTED LIFETIME (h)

85 °C
70 °C
60 °C
50 °C
10000

1000

100
0.75 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65

VOLTAGE RATIO (U/Urms)

40
 AC/DC GENERALS PURPOSE CAPACITORS
CAUTIONS AND WARNINGS

CAUTIONS AND WARNINGS

ATTENTION: IN CASE OF DENTS OF MORE THAN 1 MM IN DEPTH OR ANY OTHER MECHANICAL DAMAGE, CAPACITORS MUST NOT BE USED AT ALL.
THIS ALSO APPLIES TO CASES OF LEAKAGE. TO ENSURE THE FULL FUNCTIONALITY OF THE OVERPRESSURE DISCONNECTOR, ELASTIC ELEMENTS
MUST NOT BE HINDERED AND A MINIMUM SPACE OF 15 MM HAS TO BE KEPT ABOVE EACH CAPACITOR. CHECK TIGHTNESS OF THE
CONNECTIONS/TERMINALS PERIODICALLY. THE ENERGY STORED IN CAPACITORS MAY BE LETHAL. TO PREVENT ANY CHANCE OF SHOCK,
DISCHARGE AND SHORT CIRCUIT THE CAPACITOR BEFORE HANDLING. FAILURE TO FOLLOW CAUTIONS MAY RESULT, IN THE WORST CASE, IN
PREMATURE FAILURES, BURSTING AND FIRE. ISKRA, D.D. IS NOT RESPONSIBLE FOR ANY DAMAGE CAUSED TO PEOPLE OR THINGS AND RESULTING
FROM AN IMPROPER INSTALLATION OR A MISAPPLICATION OF CAPACITORS.

SAFETY

ATTENTION: ELECTRICAL OR MECHANICAL MISAPPLICATION OF CAPACITORS MAY BE HAZARDOUS. PERSONAL INJURY OR PROPERTY DAMAGE MAY
RESULT FROM BURSTING OF THE CAPACITOR OR FROM THE EXPULSION OF OIL ORMELTED MATERIAL DUE TO MECHANICAL DISRUPTION OF THE
CAPACITOR. ENSURE GOOD, EFFECTIVE GROUNDING FOR CAPACITOR ENCLOSURES. OBSERVE APPROPRIATE SAFETY PRECAUTIONS DURING
OPERATION (SELF-RECHARGING PHENOMENA AND HIGH ENERGY CONTAINED IN THE CAPACITOR). HANDLE CAPACITORS CAREFULLY, BECAUSE
EVEN AFTER THE DISCONNECTION THEY MAY STILL BE CHARGED. THE TERMINALS OF CAPACITORS, CONNECTED BUS BARS AND CABLES AS WELL
AS OTHER DEVICES MAY ALSO BE ENERGIZED. FOLLOW GOOD ENGINEERING PRACTICE.

THERMAL LOAD

ATTENTION: AFTER INSTALLATION OF THE CAPACITOR IT IS NECESSARY TO VERIFY THAT MAXIMUM HOT SPOT TEMPERATURE DOES NOT EXCEED
DURING EXTREME SERVICE CONDITIONS.

MECHANICHAL PROTECTION

ATTENTION: THE CAPACITOR HAS TO BE INSTALLED IN SUCH A WAY AS TO AVOID ANY MECHANICAL DAMAGE AND DENTS IN THE ALUMINIUM.

STORAGE AND OPERATING CONDITIONS

ATTENTION: DO NOT USE OR STORE CAPACITORS IN CORROSIVE ATMOSPHERE, ESPECIALLY WHERE CHLORIDE GAS, SULFIDE GAS, ACID, ALKALI,
SALT OR THE LIKE ARE PRESENT. IN DUSTY ENVIRONMENTS, IT IS REQUIRED TO PERFORM REGULAR MAINTENANCE AND PROPER CLEANING,
ESPECIALLY OF THE TERMINALS, TO AVOID CONDUCTIVE PATH BETWEEN PHASES AND/OR PHASES AND GROUND. THE MAXIMUM STORAGE
TEMPERATURE IS 85 °C.

OVERPRESSURE DISCONNECTOR

ATTENTION: TO ENSURE FULL FUNCTIONALITY OF AN OVERPRESSURE DISCONNECTOR, THE FOLLOWING MUST BE OBSERVED: THE ELASTIC
ELEMENTS MUST BE HINDERED, I.E.: CONNECTING LINES MUST BE FLEXIBLE LEADS (CABLES); THERE MUST BE ENOUGH SPACE FOR EXPANSION
ABOVE THE CONNECTIONS; FOLDING CRIMPS MUST NOT BE RETAINED BY CLAMPS; STRESS PARAMETERS OF THE CAPACITOR MUST FOLLOWIEC
61071 SPECIFICATION.

41
 AC FILTERING CAPACITORS
TYPE KNB1910, KNB1914

APPLICATIONS

INPUT/OUTPUT AC FILTERS FOR POWER CONVERTERS

SWITCHING MODE POWER SUPPLIES (SMPS)
SOLAR POWER PLANTS
WIND PLANTS
MOTOR DRIVES
INDUCTION HEATERS
FREQUENCY INVERTERS
UNINTERRUPTIBLE POWER SUPPLIES (UPS)

REFERENCE STANDARD FEATURES

IEC 61071 SELF-HEALING PROPERTIES

HIGH RIPPLE CURRENT
HIGH RELIABILITY
LOW LOSSES
SMALL DIMENSIONS
DESIGNED FOR PCB MOUNTING

SPECIFICATIONS

RATED CAPACITANCE 0.1 µF TO 80 µF

CAPACITANCE TOLERANCE ± 5 %, ± 10 %
RATED RMS VOLTAGE Urms 250 V AC, 300 V AC, 350 V AC, 400 V AC, 440 V AC
OPERATING TEMPERATURE RANGE -40 °C TO 85 °C
CLIMATIC CATEGORY 40/85/56 ACCORDING TO IEC 60068-1
LIFE EXPECTANCY ≥60 000 HOURS AT Urms , θhs = 70 °C
RATED TEMPERATURE 85°C
MAX. HOT SPOT TEMPERATURE 105 °C

34
42
 AC FILTERING CAPACITORS
TYPE KNB1910, KNB1914

GENERAL CHARACTERISTICS

CAPACITANCE RANGE
Urms @ 85 °C = 250 V AC, UN @ 85 °C = 350 V AC, UNDC @ 85 °C = 600 V DC

CN (1)
Dimensions (mm) (2) tan(δ)@1kHz (3) ESR@10 kHz (4) Imax@10 kHz (5) (dU/dt)max Î
(µF) L H W P P1 (x10-4) (mW) (A) (V/µs) (A)
1 32.0 19.0 10.0 27.5 – 10 30.0 4.0 32 32
2 32.0 19.0 10.0 27.5 – 10 24.3 4.5 32 64
3 32.0 21.0 12.0 27.5 – 10 17.1 5.8 32 96
4 32.0 22.0 13.0 27.5 – 10 13.5 6.7 32 128
5 32.0 24.5 15.0 27.5 – 10 11.0 8.0 32 160
6 32.0 26.5 17.0 27.5 – 10 9.5 9.0 32 192
7 32.0 28.0 18.0 27.5 – 10 8.2 10.0 32 224
8 32.0 32.0 18.0 27.5 – 10 7.3 11.1 32 256
9 32.0 33.0 20.0 27.5 –/10.2 10 6.5 12.3 32 288
10 32.0 35.0 20.0 27.5 –/10.2 10 5.9 13.2 32 320
12 32.0 35.5 24.0 27.5 –/10.2 10 4.9 15.2 32 384
15 32.0 40.0 25.0 27.5 –/10.2 10 4.0 17.8 32 480
8 42.0 27.0 16.0 37.5 – 10 15.0 7.9 23 184
9 42.0 27.0 16.0 37.5 – 10 13.5 8.3 23 207
10 42.0 31.0 18.0 37.5 10.2 10 12.3 9.4 23 230
11 42.0 31.0 18.0 37.5 10.2 10 11.4 9.7 23 253
12 42.0 31.0 18.0 37.5 10.2 10 10.8 10.0 23 276
15 42.0 38.0 21.0 37.5 10.2 10 8.7 12.1 23 345
20 42.0 43.0 28.0 37.5 10.2 10 6.6 14.1 23 460
22 42.0 43.0 28.0 37.5 10.2 10 6.0 14.8 23 506
25 42.0 43.0 28.0 37.5 10.2 10 5.5 15.5 23 575
30 42.0 45.0 30.0 37.5 10.2/20.3 15 5.0 16.9 23 690
35 42.0 50.0 36.0 37.5 10.2/20.3 15 4.5 19.1 23 805
40 42.0 50.0 36.0 37.5 10.2/20.3 15 4.0 20.2 23 920
40 57.5 45.0 30.0 52.5 20.3 25 4.7 19.2 15 600
45 57.5 45.0 30.0 52.5 20.3 25 4.2 20.3 15 675
50 57.5 50.0 35.0 52.5 20.3 25 3.8 22.9 15 750
55 57.5 50.0 35.0 52.5 20.3 25 3.5 23.9 15 825
60 57.5 50.0 35.0 52.5 20.3 30 3.2 25.0 15 900
65 57.5 50.0 35.0 52.5 20.3 30 3.0 25.8 15 975
70 57.5 50.0 35.0 52.5 20.3 30 2.9 26.2 15 1050
75 57.5 55.0 40.0 52.5 20.3 30 2.8 27.4 15 1125
80 57.5 55.0 40.0 52.5 20.3 30 2.7 27.9 15 1200

NOTES:
(1)
CAPACITANCE VALUE MEASURED AT 1 kHz. INTERMEDIATE CAPACITANCE VALUES AVAILABLE ON REQUEST.
(2)
NOMINAL DIMENSIONS.
(3)
MAXIMUM tan(δ) VALUES.
(4)
TYPICAL EQUIVALENT SERIES RESISTANCE AT 10 kHz.
(5)
MAXIMUM R.M.S. CURRENT AT 10 kHz, θamb = 70°C FOR Δθcase≤ 20°C.

43
 AC FILTERING CAPACITORS
TYPE KNB1910, KNB1914

GENERAL CHARACTERISTICS

CAPACITANCE RANGE
Urms @ 85 °C = 300 V AC, UN @ 85 °C = 420 V AC, UNDC @ 85 °C = 750 V DC

CN(1)
Dimensions (mm) (2) tan(δ)@1kHz (3) ESR@10 kHz (4) Imax@10 kHz (5) (dU/dt)max Î
(µF) L H W P P1 (x10-4) (mW) (A) (V/µs) (A)
1 32.0 19.0 10.0 27.5 – 10 30.0 4.0 40 40
2 32.0 21.0 12.0 27.5 – 10 19.8 5.3 40 80
3 32.0 24.5 15.0 27.5 – 10 14.0 7.1 40 120
3.3 32.0 24.5 15.0 27.5 – 10 13.0 7.3 40 132
4 32.0 26.5 17.0 27.5 – 10 11.0 8.4 40 160
5 32.0 32.0 18.0 27.5 – 10 9.5 9.7 40 200
6 32.0 33.0 20.0 27.5 –/10.2 10 8.3 10.9 40 240
7 32.0 33.5 24.0 27.5 –/10.2 10 7.3 12.4 40 280
8 32.0 40.0 25.0 27.5 –/10.2 10 6.6 13.8 40 320
9 32.0 40.0 25.0 27.5 –/10.2 10 6.0 14.4 40 360
10 32.0 40.0 25.0 27.5 –/10.2 10 5.5 15.1 40 400
5 42.0 27.0 16.0 37.5 – 10 17.0 7.4 28 140
5.6 42.0 27.0 16.0 37.5 – 10 15.4 7.8 28 157
6 42.0 31.0 18.0 37.5 10.2 10 14.5 8.6 28 168
7 42.0 31.0 18.0 37.5 10.2 10 13.2 9.0 28 196
7.5 42.0 38.0 21.0 37.5 10.2 10 12.5 10.1 28 210
8 42.0 38.0 21.0 37.5 10.2 10 12.0 10.3 28 224
9 42.0 38.0 21.0 37.5 10.2 10 11.0 10.7 28 252
10 42.0 38.0 21.0 37.5 10.2 10 10.0 11.3 28 280
12 42.0 43.0 28.0 37.5 10.2 10 8.5 12.4 28 336
15 42.0 43.0 28.0 37.5 10.2 10 6.8 13.9 28 420
16 42.0 43.0 28.0 37.5 10.2 10 6.5 14.2 28 448
20 42.0 45.0 30.0 37.5 10.2/20.3 15 5.3 16.4 28 560
25 42.0 50.0 36.0 37.5 10.2/20.3 15 4.3 19.5 28 700
25 57.5 45.0 30.0 52.5 20.3 15 6.8 16.0 19 475
30 57.5 50.0 35.0 52.5 20.3 15 5.8 18.5 19 570
35 57.5 50.0 35.0 52.5 20.3 20 5.0 20.0 19 665
40 57.5 50.0 35.0 52.5 20.3 20 4.4 19.9 19 760
45 57.5 55.0 40.0 52.5 20.3 20 4.0 22.9 19 855
50 57.5 55.0 40.0 52.5 20.3 20 3.6 24.2 19 950
55 57.5 55.0 40.0 52.5 20.3 20 3.3 25.3 19 1045

NOTES:
(1)
CAPACITANCE VALUE MEASURED AT 1 kHz. INTERMEDIATE CAPACITANCE VALUES AVAILABLE ON REQUEST.
(2)
NOMINAL DIMENSIONS.
(3)
MAXIMUM tan(δ) VALUES.
(4)
TYPICAL EQUIVALENT SERIES RESISTANCE AT 10 kHz.
(5)
MAXIMUM R.M.S. CURRENT AT 10 kHz, θamb = 70°C FOR Δθcase≤ 20°C.

44
 AC FILTERING CAPACITORS
TYPE KNB1910, KNB1914

GENERAL CHARACTERISTICS

CAPACITANCE RANGE
Urms @ 85 °C = 350 V AC, UN @ 85 °C = 490 V AC, UNDC @ 85 °C = 900 V DC

CN (1)
Dimensions (mm) (2) tan(δ)@1kHz (3) ESR@10 kHz (4) Imax@10 kHz (5) (dU/dt)max Î
(µF) L H W P P1 (x10-4) (mW) (A) (V/µs) (A)
1 32.0 19.0 10.0 27.5 – 10 30.0 4.0 50 50
1.2 32.0 21.0 12.0 27.5 – 10 25.0 4.8 50 60
2 32.0 24.5 15.0 27.5 – 10 17.0 6.4 50 100
2.2 32.0 24.5 15.0 27.5 – 10 16.0 6.6 50 110
3 32.0 28.0 18.0 27.5 – 10 12.5 8.1 50 150
3.3 32.0 32.0 18.0 27.5 – 10 11.5 8.8 50 165
4 32.0 32.0 18.0 27.5 – 10 9.8 9.6 50 200
5 32.0 40.0 25.0 27.5 –/10.2 10 8.5 12.1 50 250
6 32.0 40.0 25.0 27.5 –/10.2 10 7.5 12.9 50 300
7 32.0 40.0 25.0 27.5 –/10.2 10 6.8 13.6 50 350
7.5 32.0 40.0 25.0 27.5 –/10.2 10 6.5 13.9 50 375
4 42.0 27.0 16.0 37.5 – 10 19.0 7.0 35 140
5 42.0 31.0 18.0 37.5 10.2 10 16.0 8.2 35 175
6 42.0 38.0 21.0 37.5 10.2 10 13.5 9.7 35 210
7 42.0 38.0 21.0 37.5 10.2 10 11.8 10.4 35 245
8 42.0 38.0 21.0 37.5 10.2 10 10.5 11.0 35 280
9 42.0 43.0 28.0 37.5 10.2 10 9.5 11.8 35 315
10 42.0 43.0 28.0 37.5 10.2 10 8.8 12.2 35 350
12 42.0 43.0 28.0 37.5 10.2 10 7.3 13.4 35 420
14 42.0 45.0 30.0 37.5 10.2/20.3 15 6.5 14.8 35 490
15 42.0 45.0 30.0 37.5 10.2/20.3 15 6.0 15.4 35 525
18 42.0 50.0 36.0 37.5 10.2/20.3 15 5.0 18.1 35 630
20 42.0 50.0 36.0 37.5 10.2/20.3 15 4.5 19.1 35 700
18 57.5 45.0 30.0 52.5 20.3 15 8.7 14.1 23 414
20 57.5 45.0 30.0 52.5 20.3 15 7.9 14.8 23 460
22 57.5 50.0 35.0 52.5 20.3 20 7.2 16.6 23 506
24 57.5 50.0 35.0 52.5 20.3 20 6.7 17.3 23 552
25 57.5 50.0 35.0 52.5 20.3 20 6.5 17.5 23 575
26 57.5 50.0 35.0 52.5 20.3 20 6.3 17.8 23 598
30 57.5 55.0 40.0 52.5 20.3 20 5.5 19.6 23 690
35 57.5 55.0 40.0 52.5 20.3 20 4.8 20.9 23 805

NOTES:
(1)
CAPACITANCE VALUE MEASURED AT 1 kHz. INTERMEDIATE CAPACITANCE VALUES AVAILABLE ON REQUEST.
(2)
NOMINAL DIMENSIONS.
(3)
MAXIMUM tan(δ) VALUES.
(4)
TYPICAL EQUIVALENT SERIES RESISTANCE AT 10 kHz.
(5)
MAXIMUM R.M.S. CURRENT AT 10 kHz, θamb = 70°C FOR Δθcase≤ 20°C.

45
 AC FILTERING CAPACITORS
TYPE KNB1910, KNB1914

GENERAL CHARACTERISTICS

CAPACITANCE RANGE
Urms @ 85 °C = 400 V AC, UN @ 85 °C = 560 V AC, UNDC @ 85 °C = 1000 V DC

CN(1)
Dimensions (mm) (2) tan(δ)@1kHz (3) ESR@10 kHz (4) Imax@10 kHz (5) (dU/dt)max Î
(µF) L H W P P1 (x10-4) (mW) (A) (V/µs) (A)
0.47 32.0 16.0 7.5 27.5 – 10 45.0 2.9 57 27
0.56 32.0 17.0 9.0 27.5 – 10 40.0 3.3 57 32
0.68 32.0 19.0 10.0 27.5 – 10 38.0 3.6 57 39
0.82 32.0 21.0 12.0 27.5 – 10 33.0 4.1 57 47
1 32.0 21.0 12.0 27.5 – 10 28.0 4.5 57 57
1.5 32.0 24.5 15.0 27.5 – 10 20.0 5.9 57 86
2 32.0 26.5 17.0 27.5 – 10 16.0 6.9 57 114
2.2 32.0 26.5 17.0 27.5 – 10 15.0 7.2 57 125
3 32.0 33.0 20.0 27.5 –/10.2 10 11.5 9.2 57 171
3.5 32.0 35.0 20.0 27.5 –/10.2 10 10.5 9.8 57 200
5 32.0 40.0 25.0 27.5 –/10.2 10 7.5 12.9 57 285
2.7 42.0 27.0 16.0 37.5 – 10 20.0 6.8 40 108
3 42.0 31.0 18.0 37.5 10.2 10 19.0 7.5 40 120
3.5 42.0 31.0 18.0 37.5 10.2 10 17.0 8.0 40 140
4 42.0 38.0 21.0 37.5 10.2 10 15.0 9.2 40 160
5 42.0 38.0 21.0 37.5 10.2 10 12.0 10.3 40 200
6 42.0 43.0 28.0 37.5 10.2 10 10.3 11.3 40 240
7 42.0 43.0 28.0 37.5 10.2 10 9.0 12.1 40 280
7.5 42.0 43.0 28.0 37.5 10.2 10 8.6 12.4 40 300
8 42.0 43.0 28.0 37.5 10.2 10 8.3 12.6 40 320
9 42.0 45.0 30.0 37.5 10.2/20.3 10 7.6 13.7 40 360
10 42.0 45.0 30.0 37.5 10.2/20.3 15 7.0 14.3 40 400
12 42.0 50.0 36.0 37.5 10.2/20.3 15 6.0 16.5 40 480
13 42.0 50.0 36.0 37.5 10.2/20.3 15 5.6 17.1 40 520
13 57.5 45.0 30.0 52.5 20.3 15 8.2 14.6 27 351
14 57.5 45.0 30.0 52.5 20.3 15 7.7 15.0 27 378
15 57.5 45.0 30.0 52.5 20.3 20 7.3 15.4 27 405
16 57.5 50.0 35.0 52.5 20.3 20 7.0 16.9 27 432
18 57.5 50.0 35.0 52.5 20.3 20 6.3 17.8 27 486
20 57.5 50.0 35.0 52.5 20.3 20 5.7 18.7 27 540
22 57.5 55.0 40.0 52.5 20.3 20 5.2 20.1 27 594
25 57.5 55.0 40.0 52.5 20.3 20 4.6 21.4 27 675
26 57.5 55.0 40.0 52.5 20.3 20 4.4 21.9 27 702

NOTES:
(1)
CAPACITANCE VALUE MEASURED AT 1 kHz. INTERMEDIATE CAPACITANCE VALUES AVAILABLE ON REQUEST.
(2)
NOMINAL DIMENSIONS.
(3)
MAXIMUM tan(δ) VALUES.
(4)
TYPICAL EQUIVALENT SERIES RESISTANCE AT 10 kHz.
(5)
MAXIMUM R.M.S. CURRENT AT 10 kHz, θamb = 70°C FOR Δθcase≤ 20°C.

46
 AC FILTERING CAPACITORS
TYPE KNB1910, KNB1914

GENERAL CHARACTERISTICS

CAPACITANCE RANGE
Urms @ 85 °C = 440 V AC, UN @ 85 °C = 620 V AC, UNDC @ 85 °C = 1100 V DC

CN (1)
Dimensions (mm) (2) tan(δ)@1kHz (3) ESR@10 kHz (4) Imax@10 kHz (5) (dU/dt)max Î
(µF) L H W P P1 (x10-4) (mW) (A) (V/µs) (A)
0.1 32.0 16.0 7.5 27.5 – 10 100.0 2.0 150 15
0.15 32.0 16.0 7.5 27.5 – 10 70.0 2.4 150 23
0.22 32.0 17.0 9.0 27.5 – 10 55.0 2.8 150 33
0.33 32.0 17.0 9.0 27.5 – 10 45.0 3.1 150 50
0.47 32.0 19.0 10.0 27.5 – 10 35.0 3.7 150 71
0.56 32.0 21.0 12.0 27.5 – 10 33.0 4.1 150 84
0.68 32.0 22.0 13.0 27.5 – 10 30.0 4.5 150 102
0.82 32.0 24.5 15.0 27.5 – 10 25.0 5.1 150 123
1 32.0 24.5 15.0 27.5 – 10 22.0 5.6 150 150
1.5 32.0 28.0 18.0 27.5 – 10 16.0 7.2 150 225
2 32.0 33.0 20.0 27.5 –/10.2 10 13.0 8.7 150 300
2.2 32.0 35.0 20.0 27.5 –/10.2 10 12.0 9.2 150 330
3 32.0 40.0 25.0 27.5 –/10.2 10 10.0 11.2 150 450
1.5 42.0 27.0 16.0 37.5 – 15 21.0 6.7 100 150
2 42.0 31.0 18.0 37.5 10.2 15 17.0 8.0 100 200
2.2 42.0 31.0 18.0 37.5 10.2 15 16.0 8.2 100 220
3 42.0 38.0 21.0 37.5 10.2 15 12.0 10.3 100 300
3.3 42.0 38.0 21.0 37.5 10.2 15 11.0 10.7 100 330
4 42.0 38.0 21.0 37.5 10.2 15 10.5 11.0 100 400
4.7 42.0 43.0 28.0 37.5 10.2 15 9.5 11.8 100 470
5 42.0 43.0 28.0 37.5 10.2 15 9.0 12.1 100 500
5.6 42.0 43.0 28.0 37.5 10.2 15 8.2 12.7 100 560
6 42.0 45.0 30.0 37.5 10.2/20.3 15 7.8 13.5 100 600
6.8 42.0 45.0 30.0 37.5 10.2/20.3 15 7.0 14.3 100 680
7 42.0 50.0 36.0 37.5 10.2/20.3 15 6.9 15.4 100 700
8 42.0 50.0 36.0 37.5 10.2/20.3 15 6.2 16.3 100 800
8 57.5 45.0 30.0 52.5 20.3 20 6.5 16.4 65 520
9 57.5 45.0 30.0 52.5 20.3 20 6.2 16.7 65 585
10 57.5 45.0 30.0 52.5 20.3 20 5.8 17.3 65 650
12 57.5 50.0 35.0 52.5 20.3 20 5.0 20.0 65 780
15 57.5 55.0 40.0 52.5 20.3 20 4.1 22.7 65 975
16 57.5 55.0 40.0 52.5 20.3 20 4.0 22.9 65 1040
18 57.5 55.0 40.0 52.5 20.3 20 3.9 23.2 65 1170

NOTES:
(1)
CAPACITANCE VALUE MEASURED AT 1 kHz. INTERMEDIATE CAPACITANCE VALUES AVAILABLE ON REQUEST.
(2)
NOMINAL DIMENSIONS.
(3)
MAXIMUM TAN(δ) VALUES.
(4)
TYPICAL EQUIVALENT SERIES RESISTANCE AT 10 kHz.
(5)
MAXIMUM R.M.S. CURRENT AT 10 kHz, θamb = 70°C FOR Δθcase≤ 20°C.

47
 AC FILTERING CAPACITORS
APPLICATIONS

WIND PLANTS
FREQUENCY INVERTERS

DC/AC
INVERTER
DC/AC
INVERTER

SOLAR POWER PLANTS

DC (AC)/AC (DC)
INVERTER
DC (AC)/AC (DC)
INVERTER
WELDING EQUIPMENT
DC (AC)/AC (DC)
INVERTER

IGBT MODULE
HYBRID VEHICLES

UPS SYSTEMS

DIMENSIONS

KNB1910 (2 PINS) KNB1914 (4 PINS)

L W L W
H
H

4 or 6
4 or 6

P d P d
P1

TERMINAL DIMENSIONS MAX. BOX DIMENSIONS

P TOLERANCE P1 TOLERANCE d TOLERANCE Lmax Hmax Wmax
(mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm)
27.5 ±0.5 – – 0.8 ±0.05 L + 0.5 H + 0.2 W + 0.5
27.5 ±0.5 10.2 ±0.5 1 OR 1.2 ±0.05 L + 0.5 H + 0.2 W + 0.5
37.5 ±0.5 10.2 ±0.5 1 OR 1.2 ±0.05 L + 0.5 H + 0.5 W + 0.5
37.5 ±0.5 20.3 ±0.5 1 OR 1.2 ±0.05 L + 0.5 H + 0.5 W + 0.5
52.5 ±0.5 20.3 ±0.5 1.2 ±0.05 L + 1.0 H + 1.0 W + 1.0

48
 AC FILTERING CAPACITORS
CONSTRUCTION, CAUTIONS AND WARNINGS

INTERNAL CONSTRUCTION

FIRST CONTACT LAYER

SECOND CONTACT LAYER

POLYPROPYLENE FILM DIELECTRIC METALLIZED LAYER

METAL-SPRAYED CONTACT LAYERS

NOTE: CAPACITORS WITH RATED RMS VOLTAGE 440 VAC HAVE AN INTERNAL SERIAL CONNECTION.

CAUTIONS AND WARNINGS

MECHANICAL OVERLOADS

ATTENTION: THE CAPACITOR IS DESIGNED FOR MOUNTING ON A PC BOARD. DO NOT MOVE THE CAPACITOR, AFTER IT HAS BEEN SOLDERED TO
THE PC BOARD. THE CAPACITOR SHOULD NOT BE MOUNTED ON PLACES WHERE VIBRATIONS OR ACCELERATIONS OCCUR. DO NOT EXCEED THE
TESTED ABILITY TO WITHSTAND VIBRATION. AVOID ANY COMPRESSIVE, TENSILE OR FLEXURAL STRESS.

OVERLOAD

ATTENTION: DO NOT OVERLOAD THE CAPACITOR. AVOID OVERLOADING THE CAPACITOR AND CONSIDER THE FLAMMABILITY OF MATERIALS.

IMPULSES

ATTENTION: IF ELECTRIC ENERGY IMPULSES ARE HIGHER, DIELECTRIC WILL BREAK DOWN. AVOID EXTERNAL ELECTRIC ENERGY IMPULSE.
THE PEAK VOLTAGE (UP, AC) SHOULD NOT BE HIGHER THAN THE RATED DC VOLTAGE (UNDC).

ENVIRONMENTAL CONDITIONS

ATTENTION: DO NOT EXCEED OPERATING TEMPERATURE. DO NOT EXPOSE THE CAPACITOR TO HUMIDITY LONGER THAN IT IS RECOMMENDED.
DO NOT EXPOSE THE CAPACITOR TO INCREASED TEMPERATURE MORE THAN IT IS RECOMMENDED. THE DISSIPATION FACTOR MAY GO UP AND
DOWN WITH INCREASED TEMPERATURE. AVOID EXTERNAL FIRE OR ELECTRICITY.

49
 Ljubljana

PE Ljubljana PE Kondenzatorji PE Stikala PE Instrumenti PE Baterije in potenciometri

Stegne 21 Vajdova ulica 71 Ljubljanska c. 24a Otoče 5a Šentvid pri Stični 108
SI-1000 , Ljubljana SI-8333 , Semič SI-4000 , Kranj SI-4244 , Podnart SI-1296 , Šentvid pri Stični
Phone: + 386 1 513 10 00 Phone: +386 7 38 49 200 Phone: +386 4 237 21 12 Phone: +386 4 535 9114 Phone: +386 1 780 08 00

PE Galvanotehnika Iskra IP, d.o.o. Iskra Lotrič, d.o.o. Iskra ODM, d.o.o. Iskra STIK, d.o.o.
Glinek 5 Metliška cesta 8 Otoče 5a Otoče 5a Ljubljanska cesta 24a
SI-1291 , Škofljica SI-8333 , Semič SI-4244 , Podnart 4244 , Podnart SI-4000 , Kranj
Phone: +386 1 366 80 50 Phone: +386 7 384 94 54 Phone: +386 4 535 91 68 Phone: +386 4 237 21 96 Phone: +386 4 237 22 33

Iskra Tela L, d.o.o. Iskra Sistemi - M dooel Iskra Commerce, d.o.o. Iskra Hong Kong Ltd. Iskra INDIA Pvt Ltd.
Omladinska 66 Ul, Dame Gruev br. 16/5 kat Hadži Nikole Živkoviča br. 2 33 Canton Road, T.S.T. 3 shree Ganesh Glory
78250 , Laktaši 1000 , Skopje 11000 , Beograd 1705 , China HK City Appartment Nakshtra
Phone: +387 51 535 890 Phone: +389 75 444 498 Phone: +381 11 328 10 41 Phone: +852 273 00 917 Colony Near Akashwani
+852 273 01 020 Kendra, Nashik
Phone: +91 253 2346161
+91 909 6900893

Iskra, d.d.
Stegne 21 Phone: +386 (0) 1 513 10 00
SI-1000 Ljubljana, Slovenia www.iskra.eu

• Published by Iskra, d. d. • Version 4.0 September 2017