Backup / Restore does not work.

Check if the date/time are equal between the laptop and the Power Logic Controller.
The time is visible in the (remote) settings editor and printed on a "print settings".
The setting can be changed logged in as Key Operator in the KO settings, in the System section.
After the setting is changed, the controller has to be rebooted.
Notes SDS session: General: sds

Notes SDS session

Purpose
The SDS session starts and controls the NotesSDS (on the Service laptop).
Through this interface, you start the diagnostic link to the Océ TDS300 system.
If the NotesSDS is active, a small icon (SDS) is visible in the system tray of Microsoft Windows.

Below you find a short explanation of the fields in the SDS session window.

Host
IP address of the PLC, or [oceservice].

[local] to view a local sds_log.mdb file by the NotesSDS.

Password
This is the standard service password: 675756.

Start / Stop
Start / Stop button to start / stop the SDS session.
Do not forget to stop the session before you close the TSM!

Message
Actual status message of the SDS session.

SDS Application Information

These fields give the information about the SDS versions on both the laptop and the Océ TDS300
system.

System Information
These fields give information about the Océ TDS300 system.
You can see the active error with the highest priority (1 (PE) to 9 (WAR)).

System status
This field gives information about the state of the Océ TDS300 system.
NURS (Normal User Mode): while printing / plotting the technician is able to read out machine
information e.g. counters, sensors.
It is not possible to change the parameters or to activate the output tests.
SDS mode: the technician has full access to the system.

Change system status

This list box allows you to switch the system between "Normal user mode" and "SDS mode".

All active errors

09/12/2009 2
Notes SDS session: General: sds

Behind this button is a list of all the active errors.

The errors are sorted from priority 1 (PE) to 9 (WAR).
You can delete some of the errors e.g. the permanent error.

09/12/2009 3
SDS functionality: General: sds

SDS functionality
This document will geiven an overview of the new functionality / changes and improvements with
SDS.

Overview:
1. Improved SDS Installshield
2. Enter service password in LN SDS
3. Advanced "restore from machine" functionality
4. Check of dates on laptop and controller
5. Handle corrupt sds_log.mdb
6. Abort software download limited
7. Split Backup over multiple floppies
8. Make restore possible when sds_log.mdb is not present
9. Make it impossible to close SDS server.
10. Support windows XP on client.
11. Subsets backup / restore
12. Oceservice account implemented

The next sections will give detailed informationon these subjects

Improved SDS Installshield

Enter service password in LN SDS

Advanced "restore from machine" functionality

Check of dates on laptop and controller

Handle corrupt sds_log.mdb

Abort software download limited

Split Backup over multiple floppies

Make restore possible when sds_log.mdb is not present

Make it impossible to close SDS server

Support windows XP on client

Subsets backup / restore

Oceservice account implemented

09/12/2009 4
Tips and (connection) problems laptop LN SDS : General: sds

Tips and (connection) problems laptop LN SDS

Problems
Message in SDS session screen: [ CreateDispatch() failed ].
Message in SDS session screen: [ CreateDispatch() failed ].
Activate the OK button, message: [ SDS server not found ].

Problem:
The SDS on your laptop is not or wrong registered.

Solution:
1. Make a Direct Cable Connection with the controller.
2. Start the Windows Explorer and open the c:\oce\apps\sds map.
3. Activate REG.BAT by double clicking it.
4. Make sure that the file OceSds.ini is in your windows directory ( C:\windows ).
If it is not copy it from c:\oce\apps\sds to c:\windows.
5. Activate SDSserver.exe by double clicking it.
6. Now run Lotus Notes and activate the SDS session. This should now work properly.
7. If you stop Lotus Notes the SDS server can still be active (this time only) and you must stop it
manually.
You can do this by double clicking the icon in the taskbar and then you select shutdown server in
the pop-up window.
8. When this is done once, the next connection will work properly

Solving connection problems

In cases the connection between the Controller and the Service Laptop fails the following items can
be checked successively to check for the cause.

Check that your hosts file on your Laptop is correctly adapted.

Open the hosts file within your Windows95 directory with Notepad and check that the following
lines are added;
134.188.254.101 laptop
134.188.254.100 service

Ping to the controller IP address: 134.188.254.100

Ping to the laptop IP address: 134.188.254.101

Check within the Network Properties of your Laptop that in the Client for Microsoft Networks no
connection is made to a Windows NT Domain and no name is filled in within this field.

Check the hostname of the controller, no more than 12 characters.

The date on the laptop and on the controller must be the same.

Open a HyperTerminal session with the same settings as defined in the previous chapter correct
settings.
Connect a loop back plug to the COM1 port of the laptop. The plug is available as tool. (7991.531)
Characters you type should appear on the screen.
If not; your problem is the within the hardware of your Laptop.

The same action can be done on the Controller.

Before doing this the RAS services should be stopped within the Remote Access Admin application
of the Controller.
Characters you type should appear on the screen.
If not; your problem is the within the hardware of your Controller.

Connect the cable between the Controller and the Laptop and open the HyperTerminal session on

09/12/2009 5
Tips and (connection) problems laptop LN SDS : General: sds

both sides.
Characters you type on the Laptop should appear on the Controller screen and visa versa.
If not, the problem is within the cable.

Open the Remote Access Admin application of the Controller.

Open the Port Status window and try to make a connection as described in the previous chapter.
This window can give you details why the connection failed.

09/12/2009 6
01-29 Function tests overview: General: sds 01-29 Function

01-29 Function tests overview

Identification
Every test has its unique number. This number is composed in the following way:

test number = SAC-group + function group + reference

Function tests can be divided into the next groups:

Function group Number

[ Counters ] 0
[ Parameters ] 1
[ Inputs ] 2
[ Outputs ] 4
[ Specials ] 6
[ Adjustments ] 7
[ Consumables ] 8
[ Information ] 9

Definition
[ Counters ]
A counter test displays all the possible faults / warnings that are applicable for a CAS-group and the number of times
a fault / warning has been occurring since the last service visit.

[ Parameters ]
A parameter test assigns a new value to a system parameter. The value of this parameter must be accurate to
assure optimal functioning of the Océ TDS300 system. The value of this parameter can be determined by using a
system test.

[ Inputs ]
An input test is used to read the status of a digital input(s) of one of the CPU boards of the PRINTER or SCANNER.
After selecting an input test, the status of the input is periodically displayed on the SDS-U/I screen. The status of the
input will be displayed even if the system is busy scanning, printing or copying.
The SDS user can choose to look at an input in default "STATIC MODE" or in "LIVE MODE" i.e. during normal
system usage.
The displaying of the status is stopped after de-activating the input test.
There is no control-loop and no errors can and will be handled or detected.

[ Outputs ]
An output test activates one actuator of the system. This actuator is driven by a simple digital output of the CPU
boards.
There is no control-loop and no errors can and will be handled or detected.

[ Specials ]
Special tests are implemented to check the correctly functioning of a function or a part of a function. A special test
can activate several combined outputs to activate a function and also related inputs can be read simultaneously.
Special tests do not deliver quantitative information that can be applied to determine the value of a parameter.

A special test can activate a control-loop. During the time the test is active, an error may be detected and handled.

[ Adjustments ]
Adjustment tests are used to generate values to adjust a function.
In contradiction to a parameter test, no system test is used. An adjustment test is self-supporting.

During the time the test is active, an error can be detected and handled.

[ Consumables ]
A consumable test displays the actual lifetime of consumables.
No (sub) functions or outputs are activated. No errors can occur.

09/12/2009 7
01-29 Function tests overview: General: sds 01-29 Function

[ Information ]
Information tests displays the value of a (calculated) non-standard input(s) or output(s), e.g. all temperatures
measured in the fuser. Further, e.g. the presents of an optional PBA or the state, enable / disable of functionality is
displayed here.

After selecting an information test, the current value is periodically displayed on the SDS screen.
This is even done while the system is busy scanning, printing or copying.
The SDS user can choose to look at an input in default "STATIC MODE" or in "LIVE MODE" i.e. during normal
system use.
The displaying of the status is stopped after de-activating the test.

All tests are described in corresponding chapters.

09/12/2009 8
[ 30 Reset PE ]: General: sds 30-39 Analysis

[ 30 Reset PE ]
Reset permanent error.

You can see a permanent error only in the [ SDS SESSION ] test.
The reset button for a permanent error is also available in [ SDS SESSION ] test.

09/12/2009 9
[ 31 Log and Reset the fault and the service counters ]: General: sds 30-39 Analysis

[ 31 Log and Reset the fault and the service counters ]

Description Log and Reset the fault and the service counters.
Also the counters in the fault history will be updated.

Value

Remarks On of the last steps, before ending SDS session.

09/12/2009 10
[ 32 Display the last errors (overview) ]: General: sds 30-39 Analysis

[ 32 Display the last errors (overview) ]

Description Display the last errors.

The last 15 faults are displayed.

Information presented for each fault:

History, after which visit the error was generated
e.g 0 = between the last vist and now
e.g. 1 = the visit before...

Name; description of the fault.

Counter; number of times the fault has occured

Date; at the fault moment

Time; at the fault moment

Value The information is displayed in 4 SDS tests:

32.1 Display the last errors

32.2 Display the last system errors

32.3 Display the last errors in the service mode (SDS session active)

32.4 Display the last system errors in service mode (SDS session active)

Remarks

09/12/2009 11
[ 32.1 Display the last errors ]: General: sds 30-39 Analysis

[ 32.1 Display the last errors ]

Description Display the last errors.

The last 15 faults are displayed.

Information presented for each fault:

History, after which visit the error was generated
e.g 0 = between the last vist and now
e.g. 1 = the visit before...

Name; description of the fault.

Counter; number of times the fault has occured

Date; at the fault moment

Time; at the fault moment

Value

Remarks

09/12/2009 12
[ 32.2 Display the last system errors ]: General: sds 30-39 Analysis

[ 32.2 Display the last system errors ]

Description Display the last system errors.

The last 15 faults are displayed.

Information presented for each fault:

History, after which visit the error was generated
e.g 0 = between the last vist and now
e.g. 1 = the visit before...

Name; description of the fault.

Counter; number of times the fault has occured

Date; at the fault moment

Time; at the fault moment

Value

Remarks

09/12/2009 13
[ 32.3 Display the last errors during open SDS-session ]: General: sds 30-39 Analysis

[ 32.3 Display the last errors during open SDS-session ]

Description Display the last errors in system mode (SDS session active).

The last 15 faults are displayed.

Information presented for each fault:

History, after which visit the error was generated
e.g 0 = between the last vist and now
e.g. 1 = the visit before...

Name; description of the fault.

Counter; number of times the fault has occured

Date; at the fault moment

Time; at the fault moment

Value

Remarks

09/12/2009 14
[ 32.4 Display the last system errors during open SDS-session ]: General: sds 30-39 Analysis

[ 32.4 Display the last system errors during open SDS-session ]

Description Display the last system errors in service mode (SDS session active).

The last 15 faults are displayed.

Information presented for each fault:

History, after which visit the error was generated
e.g 0 = between the last vist and now
e.g. 1 = the visit before...

Name; description of the fault.

Counter; number of times the fault has occured

Date; at the fault moment

Time; at the fault moment

Value

Remarks

09/12/2009 15
[ 34 Display the top 10 error (overview) ]: General: sds 30-39 Analysis

[ 34 Display the top 10 error (overview) ]

Description Display the top 10 error

Information presented for each fault:

Item number

Fault number

Name; description of the fault.

Counter; number of times the fault has occured

Usage;

Relative;

Value The information is displayed in 4 SDS tests:

34.1 Display the top 10 errors

34.2 Display the complete system top 10 errors

Remarks

09/12/2009 16
[ 34.1 Display the top 10 error ]: General: sds 30-39 Analysis

[ 34.1 Display the top 10 error ]

Description Display the top 10 error

Information presented for each fault:

Item number

Fault number

Name; description of the fault.

Counter; number of times the fault has occured

Usage;

Relative;

Value

Remarks

09/12/2009 17
[ 34.2 Display the complete system top 10 error ]: General: sds 30-39 Analysis

[ 34.2 Display the complete system top 10 error ]

Description Display the complete system top 10 error

Information presented for each fault:

Item number

Fault number

Name; description of the fault.

Counter; number of times the fault has occured

Usage;

Relative;

Value

Remarks

09/12/2009 18
[ 35 Display the recorded errors in CAS-group ]: General: sds 30-39 Analysis

[ 35 Display the recorded errors in CAS-group ]

Description Display the recorded errors in the CAS-group

All logged errors are displayed in CAS-group order, with the items:

Fault number

Name; description of the fault.

Counter; number of times the fault has occured

Usage;

Relative;

Value

Remarks

09/12/2009 19
[ 36 Display the counters of the consumables ]: General: sds 30-39 Analysis

[ 36 Display the counters of the consumables ]

Description Display the counters of the consumables

Information presented for each consumable counter:

Consumable counter number

Consumable counter name

The current value

Value

Remarks

09/12/2009 20
[ 37 Display the settings of the parameters ]: General: sds 30-39 Analysis

[ 37 Display the settings of the parameters ]

Description Display the settings of the parameters

Information presented for each parameter:

Parameter name

The current value

The minimum range value

The maximum range value

Value

Remarks

09/12/2009 21
[ 45 Print the system settings ]: General: sds 40-69 System

[ 45 Print the system settings ]

Description Print the system settings.

The following items are selected and printed:

The Océ TDS300 configuration (options, settings, versions, configurations).

All BIOS settings

The hardware configuration of the Océ Power Logic controller

The software configuration of the Océ Power Logic controller

The status report of the total system (WIN-XP and Océ TDS300)

Value

Remarks

09/12/2009 22
[ 49 Print the test print 49 to check the optical density and the resolution ]: General: sds 40-69 System

[ 49 Print the test print 49 to check the optical density and the
resolution ]

Description Print the test print 49 to check the optical density and resolution.

The print file is stored on the Océ Power Logic controller.

Value

Remarks Selection: roll 1, 2 or manual feed.

09/12/2009 23
[ 51 Print the service test print 51 ]: General: sds 40-69 System

[ 51 Print the service test print 51 ]

Description Print the service test print 51.

A test print is made to check the print process.
The print file is stored on the Océ Power Logic controller.

Value Selection:

Roll 1

Roll 2

Manual feed

Remarks

09/12/2009 24
[ 52 Print the Demo Print ]: General: sds 40-69 System

[ 52 Print the Demo Print ]

Description Print the Demo print.

This print contains a drawing of the Océ TDS300 and an image of the Quick
Referece Card.

Value

Remarks

09/12/2009 25
[ 54 Print the test print 54 to check the correct working of the print head ]: General: sds 40-69 System

[ 54 Print the test print 54 to check the correct working of the print
head ]

Description Print the test print 54 to check the correct working of the print head

Value This test will disable the connection from Océ Power Logic controller to the
printhead interface PBA.
The image is generated by the printhead interface PBA.

Remarks Adjustment procedure

09/12/2009 26
[ 70 Installation Transport employee (or technician) ]: General: sds 70-79 Installation

[ 70 Installation Transport employee (or technician) ]

The Océ TDS300 system (Océ Power Logic controller, printer and scanner) is complete adjusted in
the production department. All Océ Power Logic controller optionals are installed. If some
adjustments must be repeated during the installation, than they are enabled in the installation
menu.

The print engine can be delivered:

With or without developer.

With adjustments enabled in the installation menu.

The tables shows the adjustments that can be enabled. You can access them by the installation
menu on the operator panel of the Printer (Menu Installation, if the tests are enabled !!!!!).
Note: the SDS session must be stopped during the Installation test by the transporter.
Or error code "67"appears in the printer display. Solution: .

Print engine is NOT filled with developer

Step SDS test Description
1 05-7-001 Adjustment procedure new developer
2 12-7-008 Adjustment procedure of the trailing edge position between
the first and the following prints in a run
3 12-7-009 Adjustment procedure of the paper cut length roll 1

Print engine is filled with developer

Step SDS test Description
1 12-7-008 Adjustment procedure of the trailing edge position between
the first and the following prints in a run
2 12-7-009 Adjustment procedure of the paper cut length roll 1

09/12/2009 27
[ 70.1 Installation technician (overview) ]: General: sds 70-79 Installation

[ 70.1 Installation technician (overview) ]

The configuration is complete adjusted in the production line.

Do the next test only if:

- you want to check the performance of the configuration
- you want to tune the quality to the customer's demand
- the configuration is not the same as received from the production line (e.g. other scanner or controller or ...)

Remarks:
Next actions must be executed before you start the SDS 70 tests:
1. The developer unit is filled and adjusted (Adjustment procedure new developer) .
2. The adjustment: Trailing edge position between the first and the following prints in a run
3. The adjustment: Paper cut length of the roll 1
4. The adjustment: Leading edge position for the roll 1, 2 and manual feed

Step SDS test Description

1 70.1.1 Printer installation
2 70.1.2 Scanner installation
3 70.1.3 Océ Power Logic controller installation

09/12/2009 28
[ 70.1.1 Printer installation technician]: General: sds 70-79 Installation

[ 70.1.1 Printer installation technician]

For information about the next adjustments or SDS tests, see: Installation technician

Step SDS test Name Adjustment

1 51 Print the test print from roll 1, 2 and manual feed.

2 15-1-001 Adjust the leading edge position (PTRINSE 15B1).

Roll unit, roll1

3 51 Print the test print from roll 1.
4 12-1-051 Adjust a longer or shorter trailing edge length of roll 1
(on request customer).
5 12-1-003 Adjust the image in the width direction of
roll 1.

Roll unit, roll2

6 51 Print the test print from roll 2.
7 12-1-052 Adjust a longer or shorter trailing edge length of roll 2
(on request customer).
8 12-1-041 Adjust the image in the width direction of
roll 2.

Manual feed
9 12-6-43 Print a 841 mm blank print of roll1.
10 51 Print the test print by the manual feed.
11 15-1-003 Adjust the image in the width direction for manual feed.

Light adjustment (OD)

12 49 Print the test print for the optical density.
13 04-1-003 Adjust the light intensity for average line / text prints.
14 04-1-004 Adjust the extra light intensity for darker prints.

Modification records
15 95.2 Modification info of the Printer.
16 95.4 Modification info of the PRD (Paper Roll Drawer).

09/12/2009 29
[ 70.1.2 Scanner Installation technician]: General: sds 70-79 Installation

[ 70.1.2 Scanner Installation technician]

For information about the next adjustments or SDS tests, see: Installation technician
The scanner must be adjusted to the printer. Use the transparent test original.
Step SDS test Description Adjustment
1 09-1-001 Adjust the 1:1 accuracy in the feed direction
2 10-1-003 Adjust the image accuracy in width direction (1:1)
3 09-1-002 Adjust the start timer of the scanning
4 09-1-003 Adjust the stop timer of the scanning
5 10-1-002 Adjust the "0"-line position original (in 0.1 mm)
6 95.3 Modification info of the Scanner.

09/12/2009 30
[ 70.1.3 PLC installation technician]: General: sds 70-79 Installation

[ 70.1.3 PLC installation technician]

For information about the next adjustments or SDS tests, see: Installation technician
The PLC is pre-installed at the production.
Use the test to incorporate the settings and for information
Step Test number Name Adjustment
1 90 System configuration overview
2 91 Set the configuration indentification and the serial numbers
3 93 Set the international paper standards
4 95.1 Modification records
5 97 Preset the copy counter and set the counting method
6 98 Perset the hour counter and set the first installation date

09/12/2009 31
[ 70.2 Installation M&L (Overview) ]: General: sds 70-79 Installation

[ 70.2 Installation M&L (Overview) ]

The installation procedure for M&L is divided into 3 blocks:

Printer installation M&L assembling: SDS test 70.2.1

Printer installation M&L configuration: SDS test 70.2.2

Scanner installation M&L: SDS test 70.2.3

09/12/2009 32
[ 70.2.1 Printer Installation M&L assembling ]: General: sds 70-79 Installation

[ 70.2.1 Printer Installation M&L assembling ]

Step SDS test Name Adjustment

1 73 SWDL
2 22-6-001 Initialize non volatile data printer
3 05-1-002 Adjust the sensivity of the developer
sensor (DEVCONSE 05B1)
4 05-7-001 Adjustment procedure new developer
5 54 Print the printhead check print
6 49 Testprint process
7 04-1-003 Adjust the light intensity normal
8 04-1-004 Adjust the light intensity poster
9 51 Service test print
10 04-1-005 Adjust the light intensity left printhead
11 04-1-007 Adjust trhe light intensity for the right
printhead
12 04-1-008 Horizontal alignment of the left and the
middle printhead
13 04-1-009 Horizontal alignment of the middle and
the right printhead
14 04-1-010 Vertical alignment of the left printhead
15 04-1-012 Vertical alignment of the right printhead
16 51 Service test print
17 15-1-003 Adjust the image position in the width
direction for manual feed
18 05-1-004 Enable / disable the adjustment Enable: transport withou
procedure for new developer (05-7-001) Disable: transport with to
19 12-1-053 Enable the Installation test: Adjustment
procedure leading edge position for the
roll 1 and roll 2 (PRDLEADSE 12B3).
(12-7-008)
20 12-1-054 Enable the installation test: Adjustment
procedure of the paper cut length roll 1
(12-7-009)
21 15-1-004 Enable the installation test: Adjustment
of the leading edge position. (15-7-020)
22 91.3 Set the printer serial number

Continue with sds 70.2.2

09/12/2009 33
[ 70.2.2 Printer installation M&L configuration ]: General: sds 70-79 Installation

[ 70.2.2 Printer installation M&L configuration ]

Continuation of sds 70.2.1
Step SDS test Name Adjustment
1 12-7-008 Installation test: Adjustment procedure of
the trailing edge position between the
first and the following prints in a run.
2 12-7-009 Installation test: Adjustment procedure of
the paper cut length roll 1
3 12-7-010 Installation test: Adjustment procedure of
the paper cut length roll 2
4 51 Service test print
5 15-1-001 Setting the head margin
6 51 Service test print
7 12-1-004 Adjust the cutting length for a new roll 1
8 51 Service test print
9 12-1-006 Adjust the cutting length for a new roll 2
10 51 Service test print
11 12-1-003 Adjust the image in the width direction of
roll 1
12 51 Service test print
13 12-1-041 Adjust the image in the width direction of
roll 2
14 05-1-004 Enable / disable the adjustment Enable: transport withou
procedure new developer (05-7-001) Disable: transport with d
15 12-1-053 Disable installation test: Adjustment
procedure leading edge position for the
roll 1 and roll 2 (PRDLEADSE 12B3)
16 12-1-054 Disable the installation test: Adjustment
procedure of the paper cut length roll 1
(12-7-009)
17 15-1-004 Disable the installation test: Adjustment
of the leading edge position (15-7-020)
18 51 Service test print
19 31 Log and Reset the fault and the service
counters.

09/12/2009 34
[ 70.2.3 Scanner Installation M&L]: General: sds 70-79 Installation

[ 70.2.3 Scanner Installation M&L]

Step SDS test Description Adjustment

1 22-6-021 Initialize non volatile data scanner
2 10-6-002 Maximum exposure level
3 10-7-001 CCD allignment
4 10-7-003 CCD gain
5 10-7-002 CCD focus
6 10-7-001 CCD alignment
7 10-7-004 1:1 width and right alignment
8 22-1-051 Hardware of the scanner display.
Support of the East European
characters.

09/12/2009 35
[ 71 Backup the system data ]: General: sds 70-79 Installation

[ 71 Backup the system data ]

To avoid problems, choose always "ALL" in the Subset.

From V1

Description This test backups the SDS and Customer system settings.

Value The following options are possible;

Subset:
Create a visit directory in c:\service\visits\YYYYMMDD on the controller.
All the subsets are copied in this directory.

All:
Backup from [c:\oce\apps\applications\settings] of the:

SDS settings (sds_log.mdb, sds_info.mdb)

All customer settings files on the PLC (*.sas, *.kos, *.sm,
DumpOceTDS300Config.txt, adt.cfg)

Standard:
Backup from [c:\oce\apps\applications\settings] of the:

SDS settings (sds_log.mdb, sds_info.mdb)

Actual customer settings (current.sas, current.kos, current.sm,
OceTDS300dumpconfig.txt, adt.cfg)

Settings Editor:
Backup from [c:\oce\apps\applications\settings] of the:

All customer settings files on the PLC (current.sas, current.kos,
current.sm, DumpOceTDS300Config.txt, adt.cfg)

SDS:
Backup from [c:\oce\apps\applications\settings] of the:

SDS settings (sds_log.mdb, sds_info.mdb)

Target:

Controller only:
Places the backup files in

C:\service\visits\YYYYMMDD on the PLC

Default dir (sl)
Places the backup files in

C:\service\visits\YYYYMMDD on the PLC

The default STAR directory on the service laptop
c:\oce\backup\<System type>\<Config type>\<System serial #>\<Date>.

Other dir (sl)
Places the backup files in

C:\service\visits\YYYYMMDD on the PLC

Any directory you can browse on the service laptop

09/12/2009 36
[ 71 Backup the system data ]: General: sds 70-79 Installation

Remarks Execute a Standard backup to Other dir.

Zip this directory on your service laptop to the logfloppy for your system.
Leave this floppy at the system.

Standard backup must be done in the SDS-mode.

The backup of the SDS subset is also possible in the NUSR-mode.
The backup of the other subsets will fail.

09/12/2009 37
[ 71/72 Backup / Restore ] of the system software: When to do it?: General: sds 70-79 Installation

[ 71/72 Backup / Restore ] of the system software: When to do it?

General

The parameters of all the SDS adjustments and settings of the system are stored in the EEPROM
on the CPU pba of the printer engine.
This EEPROM is fixed on the pba with solder.

The parameters of all the client settings (key operator and system administrator) are stored in the
xxx.kos & xxx.sas files in the controller. E.g. connectivity, passwords and the settings by the [
Remote Logic ].

Changes made by the SDS or the operator panel (e.g. installation menu) are stored in the
EEPROM of the printer and then copied to the SDS application in the controller.

When the system is switched ON, the data in the EEPROM of the printer is always copied to the
SDS application in the controller.

A complete backup on a diskette contains all the system and the client settings.

When to restore the data:

After replacement of the printer CPU pba
The new EEPROM on the CPU pba has the default data.
Restore the system data from the backup diskette.
(Client settings (xxx.kos and xxx.sas) are still on the controller)

After replacement of the printhead assy (PHD + I/O pba)

The setting of the memory flag in the EEPROM of the printhead I/O pba indicates a new printhead assy.
At power on, the CPU of the printer detects the setting of the flag: new printhead assy.
Then all the settings from the printhead I/O pba are stored in the EEPROM of the CPU pba in the
printer.
The flag in the printhead I/O pba is toggled.
No restore action by service!
Make the service test print with the SDS 51 to check the light intensity.

After replacement if the prinhead I/O pba

The setting of the memory flag in the EEPROM of the printhead I/O pba indicates a new printhead I/O
pba.

09/12/2009 38
[ 71/72 Backup / Restore ] of the system software: When to do it?: General: sds 70-79 Installation

At power on, the CPU of the printer detects the setting of the flag: new printhead I/O pba.
Then all the printhead settings in the printer EEPROM are stored in the EEPROM of the printhead I/O
pba.
The flag in the printhead I/O pba is toggled.
No restore action by service!

After replacement of only the printhead or only the printhead I/O pba from another system.
The flag setting of the EEPROM of the printhead I/O pba indicates no new hardware. So, It is not
possible to store new information in the EEPROM of the printhead I/O pba!
This means that the production adjustments of the printhead quality differs from the existing printhead.
Only SDS settings, as e.g. light intensity, horizontal and vertical position can be changed.
So: NO copy / print quality guarantee.

After replacement or upgrade of the [ Power Logic Controller ]

After power on, the system data in the EEPROM of the printer is always copied (restored) to the SDS
application in the controller.
Restore the client settings: xxx.kos and xxx.sas from the backup diskette

After download of the system software

The system software is downloaded in an other EEPROM.
This EEPROM is placed in a socket.
So there is no need to restore any data!

09/12/2009 39
[ 72 Restore the system data ]: General: sds 70-79 Installation

[ 72 Restore the system data ]

To avoid problems, choose always "ALL" in the Subset.

From V1

Description This test restores the SDS and Customer system settings.

Value The following options are possible;

Subset:

All:
Restore of

SDS settings (sds_log.mdb)

All customer settings files to the PLC (*.sas, *.kos, adt.cfg)
(See remark)

All the Parameters, the Consumables and the Usage counters are sent to
the selected target destination (see [Target])

Standard:
Restore of

SDS settings (sds_log.mdb)

Actual customer settings (current.sas, current.kos, adt.cfg) (See remark)

Settings Editor:
Restore of

All customer settings files on the PLC (current.sas, current.kos, adt.cfg)
(See remark)

SDS:
Restore of

SDS settings (sds_log.mdb)

All the Parameters, the Consumables and the Usage counters are sent to
the selected target destination (see [Target])

Target:
Only for the Parameters, the Consumables and the Usage counters.

All:
Restores settings of the complete system

Controller
Restores only controller settings

Printer
Restores only printer settings

Scanner
Restores only scanner settings

Remarks The files for the settings editor (current.kos/sas) and have to be opened, applied
and saved in these applications before the settings are loaded by the system.

09/12/2009 40
[ 72 Restore the system data ]: General: sds 70-79 Installation

Open the corresponding application and login as Service Operator.

REBOOT THE CONTROLLER AND SWITCH OFF / ON ALL THE

COMPONENTS.

09/12/2009 41
[ 73 Download DESCRIPTION of the system software for the XPe PLC's]: General: sds 70-79 Installation

[ 73 Download DESCRIPTION of the system software for the XPe

PLC's]

Tools:
- a diskette.

The next list gives you a step by step description how to download the system software by SDS test 73.
The data is written in an EEPROM that is put in a socket.

1. Make sure the printer is connected to the controller.

2. Turn ON the controller and the printer.
3. Make a [Remote Desktop] connection between the laptop and the controller.
4. Activate the [ PLC_Diag.bat ] icon on the remote desktop (= the laptop).
- Follow the instructions on the screen.
- If a message internal error appear, press [ Yes ].
- The controller is in the [ Diagnostic Mode ] if the message in the DOS window shows:
- - [ Start OCI in Minimal Mode Controller Started ]. Do not close this window but minimise the
window!

5. Copy the new software file ( PreinstSwdl.ofp) to a diskette.

6. Put the diskette in the controller.
7. Copy the PreinstSwdl.ofp file from the diskette drive of the PLC A:\ to:
- the C:\Oce\Apps\SDS\Swdl directory.
- Confirm (OK) to replace the existing file.
8. Minimise the [Remote Desktop] application.

9. Activate the [Lotus Notes] SDS by the laptop and enter the SDS mode.
Note:
If the SDS version on the laptop is lower then the version on the controller, then the SDS client is
copied to the laptop.
Follow the instructions on the screen, the new SDS client is installed automatically.
10. Start the SDS test 73
(The window ['installed software'] can be empty.)
11. Select: <[Select an already on the machine available download file]>.
12. Select the pre-installed firmware Vx.x.x of the printer and start the download
Note 1: if you must download the boot and the application software, then do it one by one. Never
together!
Note 2: if the download of the boot software fails, you have to replace the EPROM / CPU pba..
13. Stop the [Lotus Notes] SDS session.

14. Maximise the [Remote Desktop] application.

15. Activate the desktop icon [PLC Normal.bat] on the remote desktop.
- Follow the instructions on the screen.
- If a message internal error appear, press [ Yes ].
16. Stop the [Remote Desktop] application.
17. Disconnect the connection between the laptop and the controller.
18. There is no need to restore any data.

The whole action takes approximately 15 minutes.

09/12/2009 42
[ 73 Download the system software (Diagnosis mode only) ]: General: sds 70-79 Installation

[ 73 Download the system software (Diagnosis mode only) ]

Description For a step by step description, see .

The download of the system software is only possible in the [ Diagnosis mode ] ,
by SDS test 20-1-010.

Downloading of several kinds of software applications:

These are:

Printer embedded software upgrades (normal releases and patches)

The following upgrades are not possible with this test:

Scanner software

Océ Power Logic controller Windows XP upgrades

Océ Power Logic controller Océ TDS300 upgrades (normal releases and
patches)

Value

Remarks There is no need to restore any data.

Note:
- If the scanner / printer refuses to enter the SWDL mode, (for example there is an engine / scanner
firmware conflict)
a message appears on the remote desktop.
Switch the scanner / printer OFF and ON and select retry on the controller.
Or download the Firmware of the scanner and the printer separately.
- Ignore any kind of warnings during or right after the download of the firmware.
- If on the PLC the SDS connection is lost or a SDS session cannot be opened, activate again the
[PLC diagnostic mode] icon,
launch the SDS, open the SDS session and restart the complete action..

09/12/2009 43
[ 73 Download the system software (Diagnosis mode only) ]: General: sds 70-79 Installation

09/12/2009 44
[ 90 Set the system configuration (overview) ]: General: sds 90-99 Service Info

[ 90 Set the system configuration (overview) ]

Test Name Remark

90 [ SYStem Configuration ] Each system component has his own configuration settings.
These settings can be pre-set in the sub-system NOVRAM or are automatically determined
component.
Activating of test 90 initialise each sub-system to find the configuration settings that are aut
determined.
Before executing this test all components must be switched on.
The configuration of each sub-system can be viewed/changed/overruled in the following tes

90.1 Set the printer configuration

90.2 Set the scanner configuration

90.3 Set the controller configuration

09/12/2009 45
[ 90.1 Set the printer configuration ]: General: sds 90-99 Service Info

[ 90.1 Set the printer configuration ]

Name Automatically detected

1 Printer yes pre
2 Number of PRD rolls yes
3 Dew preventor no pre

09/12/2009 46
[ 90.2 Set the scanner configuration ]: General: sds 90-99 Service Info

[ 90.2 Set the scanner configuration ]

Name Automatically detected Options

1 Scanner no present / not p

09/12/2009 47
[ 90.3 Set the controller configuration ]: General: sds 90-99 Service Info

[ 90.3 Set the controller configuration ]

Name Automatically detected by test 90 Options

- - -
1 Set memory size yes .... MB
2 Token ring PBA no present / not p
3 Controller platform yes GX270, OTH

09/12/2009 48
[ 91 Set the configuration identification and serial numbers (overview) ]: General: sds 90-99 Service Info

[ 91 Set the configuration identification and serial numbers

(overview) ]

Test Name Remark

91 [ Configuration identification The system as whole has a certain configurtation identification number depending o
and serial numbers ] installed system components.
The system has a serial number total system which depends on the configuration o
system.
Each system component has his own serial number. These numbers can be preset
sub-system NOVRAM via activating test 91. All numbers are checked for possible e
The configuration identification and serial numbers can be viewed / changed / overr
the following tests:

91.1 Set the system configuration identification

91.2 System serial numbers

91.3 Printer serial numbers

91.4 Scanner serial numbers

91.5 Controller serial numbers

09/12/2009 49
[ 91.1 Set the system configuration identification ]: General: sds 90-99 Service Info

[ 91.1 Set the system configuration identification ]

Select one of the presented configurations:

TDS300

TDS310

TDS340

09/12/2009 50
[ 91.2 Set the system serial number ]: General: sds 90-99 Service Info

[ 91.2 Set the system serial number ]

09/12/2009 51
[ 91.3 Set the printer serial number ]: General: sds 90-99 Service Info

[ 91.3 Set the printer serial number ]

Set the serial numbers of the TDS300 printer units.

Serial number printer
Serial number paper roll drawer

Picture serial number of the paper roll drawer.

Serial number is moved from the right side to the front of this cover plate.

09/12/2009 52
[ 91.4 Set the scanner serial number ]: General: sds 90-99 Service Info

[ 91.4 Set the scanner serial number ]

09/12/2009 53
[ 91.5 Set the controller serial number ]: General: sds 90-99 Service Info

[ 91.5 Set the controller serial number ]

Picture

The following item is available:

Item name GX270
1 Controller serial number 0693XXXXX

09/12/2009 54
[ 93 Set the international paper standards ]: General: sds 90-99 Service Info

[ 93 Set the international paper standards ]

09/12/2009 55
[ 94 Display the passwords ]: General: sds 90-99 Service Info

[ 94 Display the passwords ]

09/12/2009 56
[ 95 Display / set the modification records (overview) ]: General: sds 90-99 Service Info

[ 95 Display / set the modification records (overview) ]

Each system component has his own modification record.

95.1 Controller modifications

95.2 Printer modifications
95.3 Scanner modifications
95.4 Paper roll drawer modifications

09/12/2009 57
 [ 95.1 Display / set the controller modification records ]: General: sds 90-99 Service Info

[ 95.1 Display / set the controller modification records ]

Function
Displays and sets the modifications for the controller.

Description
The purpose of the test is to set/display the modification history of the controller.
The modification level must be identical on both the yellow modification sticker and within this test.
Adapt both if necessary.

Location of the modification sticker

09/12/2009 58
[ 95.1 Display / set the controller modification records ]: General: sds 90-99 Service Info

09/12/2009 59
 [ 95.2 Display / set the printer modification records ]: General: sds 90-99 Service Info

[ 95.2 Display / set the printer modification records ]

Function
Displays and sets the modifications for the printer.

Description
The purpose of the test is to set/display the modification history of the printer.
The modification level must be identical on both the yellow modification sticker and within this test.
Adapt both if necessary.

Location of the modification sticker

The following modification can be appropriate:

Modification Subject Note

Number
01
02

09/12/2009 60
[ 95.2 Display / set the printer modification records ]: General: sds 90-99 Service Info

03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40

09/12/2009 61
 [ 95.3 Display / set the scanner modification records ]: General: sds 90-99 Service Info

[ 95.3 Display / set the scanner modification records ]

Function
Displays and sets the modifications for the scanner.

Description
The purpose of the test is to set/display the modification history of the scanner.
The modification level must be identical on both the yellow modification sticker and within this test.
Adapt both if necessary.

Location of the modification sticker

The following modification can be appropriate:

Modification Subject Note

Number
01
02
03
04

09/12/2009 62
[ 95.3 Display / set the scanner modification records ]: General: sds 90-99 Service Info

05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40

09/12/2009 63
 [ 95.4 Display / set the paper roll drawer modification records ]: General: sds 90-99 Service Info

[ 95.4 Display / set the paper roll drawer modification records ]

Function
Displays and sets the modifications for the paper roll drawer.

Description
The purpose of the test is to set/display the modification history of the paper roll drawer.
The modification level must be identical on both the yellow modification sticker and within this test.
Adapt both if necessary.

Location of the modification sticker

The following modification can be appropriate:

Modification Subject Note

Number
01
02
03
04

09/12/2009 64
[ 95.4 Display / set the paper roll drawer modification records ]: General: sds 90-99 Service Info

05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40

09/12/2009 65
[ 97 Preset the copy counter and set the counting method ]: General: sds 90-99 Service Info

[ 97 Preset the copy counter and set the counting method ]

With this test you can pre- and set the counter and set the counting method.

1 Read and pre-set the counter

2 Set the counting method:

- meters
- square meters
- feet
- square feet

3 Set the counting method of the scanner:

- square meters
- square feet

4 Read and preset the scanner click counter since the installation.
(Counted with the configured counting method.)

09/12/2009 66
[ 98 Preset the hour counter and set the first installation date ]: General: sds 90-99 Service Info

[ 98 Preset the hour counter and set the first installation date ]

09/12/2009 67
[ 20-0-001 Error counters interfacing ] : Controller: sds 01-29 Function

[ 20-0-001 Error counters interfacing ]

Purpose
The purpose of this test is to show the error counter values, except the permanent
errors (PE).

Description
Displayed are:
- the error code
- the error message
- the error counter

The numbers are counted since the last service visit.

Note:
After each service visit the counters must be reset via SDS test 31.

09/12/2009 68
[ 20-1-001 Enable / disable, to trace the TDS300 process into log-file ] : Controller: sds 01-29 Function

[ 20-1-001 Enable / disable, to trace the TDS300 process into

log-file ]

Description Enable / disable, Level 1 or Level 2 trace of the TDS300 process into log-file
Location of the log file: C:\oce\ngc\log\diagnostic\module.trc

Value
Level 1: Internal process communication relevant for service are logged

Level 2: Level 1 information and insight process information relevant to R&D
support.
0 = Disable (default)
1 = Level 1
2 = Level 2

Remarks Reboot the controller when a value is changed.

09/12/2009 69
[ 20-1-002 The maximum size to trace the TDS300 log-file ] : Controller: sds 01-29 Function

[ 20-1-002 The maximum size to trace the TDS300 log-file ]

Description The maximum size to trace the Océ TDS300 log-file (in byte)

Value Range: 4,000 ... 1,280,000 byte

Default: 30,000

Remarks If the maximum is reached the log file will be copied to a file ... / module.old

09/12/2009 70
[ 20-1-006 Enable / disable to trace the input data from the host into log file ] : Controller: sds 01-29 Function

[ 20-1-006 Enable / disable to trace the input data from the host into
log file ]

Description Enable / disable to trace the input data from the host into log file
(Disable logging or Enable logging)

If multiple print files are sent to the TDS300, these print files are all stored on the
Océ Power Logic controller, using the name convention <inputfile.number>.

This logfile can be used to check the input data including the received controll
commands (jobticket, rcf).

Value Disable
Enable
Default = Disable

Remarks Reboot the controller when a value is changed.

09/12/2009 71
[ 20-1-009 Set the maximum size of WIN-XP log-file(s) ] : Controller: sds 01-29 Function

[ 20-1-009 Set the maximum size of WIN-XP log-file(s) ]

Description Set the maximum size of Windows XP log-file(s) (in kB)

If the maximum size is reached, the new information is added while the oldest
information is removed.

Value Range: 64 ... 4,194,240 Kbyte

Default: 512

Remarks Step size 64 Kbyte

09/12/2009 72
[ 20-1-010 Set the next WIN-XP start method, normal or diagnosis mode ] : Controller: sds 01-29 Function

[ 20-1-010 Set the next WIN-XP start method, normal or diagnosis

mode ]

Description Set the next WIN-XP start method, normal mode or diagnosis mode

Value 0 = "normal mode",

1 = "diagnosis mode"
Default = 1 "diagnosis mode"

Remarks The next restart after the "diagnosis mode" is set automatically to "normal mode".

Note 1:
How to check if the controller is started in the Diagnosis mode:
- Message in printer and scanner display: waiting for controller
- Start SDS session: session starts direct in the SDS mode and not in the NURS mode

09/12/2009 73
[ 20-6-001 Test of the SPICE PBA, image link and control link

[ 20-6-001 Test of the SPICE PBA, image link and control link
(Only in the Diagnosis Mode) ]

Only in Diagnosis Mode

Use SDS test 20-1-010 : Set next WINXPe start method.

Purpose Test of the SPICE PBA, image link and control link

Check Connect the scan input and the printer output of the SPICE PBA (loop back)
together with one of the spice cables.

Result message:
OK: test OK
Failed: Indication of the failed part.

Remarks Information is logged in a logfile spiceHWTest.log under

c:\oce\ngc\log\diagnostic.

09/12/2009 74
[ 20-6-002 Test of the hard disks of the Set memory ] : Controller: sds 01-29 Function

[ 20-6-002 Test of the hard disks of the Set memory ]

Purpose Test of the hard disks and the adapters of the Set memory.

Check Adapter: the status of the adapter (OK/Failed) and the number of the failed
adapter is displayed.
Hard disk: the status of the hard disk (OK/Failed) and the disk number of the
adapter which controls the defective disk.

Remarks The information is logged in the setMemHwTest.log file in

...../OCEROOT/log/diagnostic area.

09/12/2009 75
[ 20-6-010 Enable / disable to trace of the WIN-XPe events / errors into log file(s) ] : Controller: sds 01-29 Function

[ 20-6-010 Enable / disable to trace of the WIN-XPe events / errors

into log file(s) ]

Purpose Enable / disable to trace of the WIN-XPe events / errors into log file(s)

Check

Remarks All the Windows XPe events / errors, generated by the processes or the operating
system, are logged into one or multiple log files.

09/12/2009 76
[ 20-6-013 Disable all the tracing / logging tests of the TDS300 controller ] : Controller: sds 01-29 Function

[ 20-6-013 Disable all the tracing / logging tests of the TDS300

controller ]

Purpose Disable all the tracing / logging tests of the TDS300 controller

Check

Remarks

09/12/2009 77
[ 20-6-020 Save the TDS300 configuration into the configuration log file ] : Controller: sds 01-29 Function

[ 20-6-020 Save the TDS300 configuration into the configuration log

file ]

Purpose The total TDS300 configuration (options, settings, versions, configurations,...) is

stored in a log file.

Check

Remarks The file: "DumpOceTDS300Config.txt" is stored in

c:\oce\ngc\log\diagnostic\DumpOceTDS300Config.txt .

09/12/2009 78
[ 20-6-023 Clear the diagnostic area ] : Controller: sds 01-29 Function

[ 20-6-023 Clear the diagnostic area ]

Purpose Clear the Océ Power Logic controller diagnostic area.

All the HW logfiles, the Océ TDS300 dump config and the Functional tracing files.

Check

Remarks

09/12/2009 79
[ 20-6-025 Clear the error and the warning log files ] : Controller: sds 01-29 Function

[ 20-6-025 Clear the error and the warning log files ]

Purpose Clear the error and the warning log files

Check

Remarks

09/12/2009 80
[ 20-6-031 Clear the set memory and the spool areas

[ 20-6-031 Clear the set memory and the spool areas

(only in the Diagnosis Mode) ]

Purpose Clear the set memory and the spool areas

(only in the Diagnosis Mode)
All temporary files, locks and directories are removed from the system.

Check

Remarks

09/12/2009 81
[ 20-6-032 Save the total system configuration of WIN-XP and TDS300 into the status log file ]: Controller: sds 01-29 Function

[ 20-6-032 Save the total system configuration of WIN-XP and

TDS300 into the status log file ]

Purpose Save the total system configuration of WIN-XP and TDS300 into the status log file
(version, configuration, etc.)

Check

Remarks The file: "TDS300.txt" is stored in: c:\oce\ngc\diagnostic\TDS300.txt.

Is important information about the status of WIN-XP and the PLC.

09/12/2009 82
[ 20-6-039 Disable the tests: 20-6-013; 20-6-023; 20-6-025 and remove all images and temporary files ] : Controller: sds 01-29 Function

[ 20-6-039 Disable the tests: 20-6-013; 20-6-023; 20-6-025 and

remove all images and temporary files ]

Purpose Disable tests the tests: 20-6-013; 20-6-023; 20-6-025 remove all images and
temporary files.
The system is "clean".

Check

Remarks

09/12/2009 83
[ 22-1-046 Display the release number of the controller software ] : Controller: sds 01-29 Function

[ 22-1-046 Display the release number of the controller software ]

Description Display the release number of the controller software.

Presentation 5 /6 digits: (a)a.bb.cc (e.g. 1.15.1 = 11501).

Value Range: 1000 .... 999999

Remarks

09/12/2009 84
[ 09-0-003 Error Counters ] : Scanner\09 Originals: sds 01-29 Function

[ 09-0-003 Error Counters ]

Purpose
The purpose of this test is to show the error counter values, except the permanent
errors (PE).

Description
Displayed are:
- the error code
- the error message
- the error counter

The numbers are counted since the last service visit.

Note:
After each service visit the counters must be reset via SDS test 31.

09/12/2009 85
[ 09-1-001 Adjust the 1:1 image accuracy in the feed direction (in 0.1 mm) ] : Scanner\09 Originals: sds 01-29 Function

[ 09-1-001 Adjust the 1:1 image accuracy in the feed direction (in
0.1 mm) ]

Description Adjust the 1:1 image accuracy in the feed direction (in 0.1 mm)

Value Range: -100 ... +100

Default: 0

Remarks Adjustment description:

Adjustments: Adjust the 1:1 image accuracy in the feed direction in 0.1 mm.

09/12/2009 86
[ 09-1-002 Adjust the leading edge on the copy (in 0.1 mm) ] : Scanner\09 Originals: sds 01-29 Function

[ 09-1-002 Adjust the leading edge on the copy (in 0.1 mm) ]

Description Adjust the leading edge on the copy (in 0.1 mm)

Value Range: -100 ... +100

Default: 0

Remarks Adjustment description:

See: Adjust the leading edge on the copy in 0.1 mm.

09/12/2009 87
[ 09-1-003 Adjust the trailing edge on the copy (in 0.1 mm) ] : Scanner\09 Originals: sds 01-29 Function

[ 09-1-003 Adjust the trailing edge on the copy (in 0.1 mm) ]

Description Adjust the trailing edge on the copy (in 0.1 mm)

Value Range: -100 ... +100

Default: 0

Remarks Adjustment description:

Adjustments: Adjust the trailing edge on the copy in 0.1 mm.

09/12/2009 88
[ 09-2-001 Check of the original present sensor (ORGPRESE 09B1) ] : Scanner\09 Originals: sds 01-29 Function

[ 09-2-001 Check of the original present sensor (ORGPRESE 09B1)

]

Condition No original: Original not present.

Original available: Original present

Action Feed original or sheet

Check

09/12/2009 89
[ 09-6-001 Activate the original motor (ORGMO 09M1) ] : Scanner\09 Originals: sds 01-29 Function

[ 09-6-001 Activate the original motor (ORGMO 09M1) ]

Purpose Activate the original motor (ORGMO 09M1)

Check Transport: transport the original

Rewind: rewind the original

Remarks

09/12/2009 90
[ 09-6-002 Activate the movement of the original ] : Scanner\09 Originals: sds 01-29 Function

[ 09-6-002 Activate the movement of the original ]

Purpose Check of the orignal transport in the scanner

Check Insert an original.

Activate the SDS test: The original is transported into the scanner and rewind.
The cycle will be repeated till the test is stopped.

Remarks

09/12/2009 91
[ 09-9-001 Display the length of the last original (in 0.1 mm) ] : Scanner\09 Originals: sds 01-29 Function

[ 09-9-001 Display the length of the last original (in 0.1 mm) ]

Purpose Display the length of the last original (in 0.1 mm)

Check Feed an original.

Original length: ..... in 0.1 mm

Remarks

09/12/2009 92
[ 10-0-003 Error counters ] : Scanner\10 Scanning: sds 01-29 Function

[ 10-0-003 Error counters ]

Purpose
The purpose of this test is to show the error counter values, except the permanent
errors (PE).

Description
Displayed are:
- the error code
- the error message
- the error counter

The numbers are counted since the last service visit.

Note:
After each service visit the counters must be reset via SDS test 31.

09/12/2009 93
[ 10-1-001 Set the lamp time out after the last original (in seconds) ] : Scanner\10 Scanning: sds 01-29 Function

[ 10-1-001 Set the lamp time out after the last original (in seconds) ]

Description Set the lamp time out after the last original (in seconds)

Value Range: 60 ... 600

Default: 60 (seconds)

Remarks

09/12/2009 94
[ 10-1-002 Adjust the "0"-line position original - copy (in 0.1 mm) ] : Scanner\10 Scanning: sds 01-29 Function

[ 10-1-002 Adjust the "0"-line position original - copy (in 0.1 mm) ]

Description Adjust the "0"-line position original - copy (in 0.1 mm)

Value Range: -150 ... 300

Default: 0

Remarks Adjustment description:

Adjustments: Adjustment procedure of the 1:1 width and right alignment.
The value is automatically calculated by sds 10-7-004.

09/12/2009 95
[ 10-1-003 Adjust the image accuracy in the width direction (1:1) (in 0.1 mm) ] : Scanner\10 Scanning: sds 01-29 Function

[ 10-1-003 Adjust the image accuracy in the width direction (1:1) (in
0.1 mm) ]

Description Adjust the image accuracy in the width direction (1:1) (in 0.1 mm)

Value Range: -100 ... +100

Default: 0

Remarks Adjustment description:

Adjustments: Adjustment procedure of the 1:1 width and right alignment.
The value is automatically calculated by sds 10-7-004.

09/12/2009 96
[ 10-1-004 Adjust the light level of the exposure lamp (in steps of 1 %) ] : Scanner\10 Scanning: sds 01-29 Function

[ 10-1-004 Adjust the light level of the exposure lamp (in steps of 1
%) ]

Description Adjust the light level of the exposure lamp (in steps of 5 %)

Value Range: 27 ... 60

Default: 45

Remarks Check for the correct O.D.

09/12/2009 97
[ 10-2-001 Check of the exposure sensor (SCAEXPOSE 10PBA04) ] : Scanner\10 Scanning: sds 01-29 Function

[ 10-2-001 Check of the exposure sensor (SCAEXPOSE 10PBA04) ]

Condition Check the function of the exposure sensor (SCAEXPOSE 10PBA04)

Action

Check Check the function of the sensor with a flash light.

09/12/2009 98
[ 10-6-002 Check the functioning of the exposure lamp (SCALA 10E1) ] : Scanner\10 Scanning: sds 01-29 Function

[ 10-6-002 Check the functioning of the exposure lamp (SCALA

10E1) ]

Purpose Check the functioning of the exposure lamp (SCALA 10E1).

Check Lamp on: light output is placed at 100%.

Display the status of the sensor EXPOSEIN.

Remarks

09/12/2009 99
[ 10-7-001 Adjustment procedure of the CCD alignment ] : Scanner\10 Scanning: sds 01-29 Function

[ 10-7-001 Adjustment procedure of the CCD alignment ]

Purpose Adjustment procedure of the CCD alignment

Value Allignment right: 100 ... 1100 (pixels)

Normal value: 600

Allignment left: 6400 - 7400 (pixels)

Normal value: 6900

Remarks Adjustment description:

Adjustments: Adjustment procedure of the CCD alignment (Position of the CCD
with the scan line).

09/12/2009 100
[ 10-7-002 Adjustment procedure of the CCD focus ] : Scanner\10 Scanning: sds 01-29 Function

[ 10-7-002 Adjustment procedure of the CCD focus ]

Purpose Adjustment procedure of the CCD focus

Value The contrast of a lign pattern is measured.

Remarks Adjustment description:

Adjustments: Adjustment procedure of the CCD focus.

09/12/2009 101
[ 10-7-003 Adjustment procedure of the CCD exposure level ] : Scanner\10 Scanning: sds 01-29 Function

[ 10-7-003 Adjustment procedure of the CCD exposure level ]

Purpose Adjust the odd and even CCD pixels to the same and optimum exposure level.

Value Within the range 223 - 227.

Remarks Adjustment description:

Adjustments: Adjustment procedure of the CCD Gain (Exposure level).

09/12/2009 102
[ 10-7-004 Adjustment procedure of the 1:1 width and right alignment ] : Scanner\10 Scanning: sds 01-29 Function

[ 10-7-004 Adjustment procedure of the 1:1 width and right

alignment ]

Purpose Adjustment procedure of the 1:1 width and right alignment

Value The values are calculated automatically.

The valus are stored in:
1:1width: in sds 10-1-003
"0"-line: in sds 10-1-002

Remarks Adjustment description:

Adjustments: Adjustment procedure of the 1:1 width and right alignment.

09/12/2009 103
[ 11-6-001 Check of the control bus between CPU-IO and the IMAGE- PROC PBA ] : Scanner\11 Image Processing: sds 01-29 Function

[ 11-6-001 Check of the control bus between CPU-IO and the

IMAGE- PROC PBA ]

Warning

Caution

Purpose Check of the control bus between CPU-IO and the IMAGE- PROC PBA of the
scanner

Check Image PROC OK

Image PROC NOT OK

Remarks

09/12/2009 104
[ 22-0-003 Error counters of the scanner ] : Scanner\22 Power & Control: sds 01-29 Function

[ 22-0-003 Error counters of the scanner ]

Purpose
The purpose of this test is to show the error counter values, except the permanent
errors (PE).

Description
Displayed are:
- the error code
- the error message
- the error counter

The numbers are counted since the last service visit.

Note:
After each service visit the counters must be reset via SDS test 31.

09/12/2009 105
[ 22-1-051 Display / set the scanner display for languages with a special character set ] : Scanner\22 Power & Control: sds 01-29 Functio

[ 22-1-051 Display / set the scanner display for languages with a

special character set ]

From R1.2
Set the SDS test to '1' to display the Polish and de Czech language on the operator display.

Description Display / set the scanner display to include the special character set for the
Polish and the Czech language.

Value Range: 0 or 1
Default: 0
0 = universal font or Japanese language
1 = universal font with the special character set for the Polish and the Czech
language.

Remarks For R1.1: no SDS test is available and the old panel display can not present the
special character set.
For R1.2: only the new display in the operator panel can display the special
character set. See the partslist.

09/12/2009 106
[ 22-6-021 Set the NVD to default in the RAM of the scanner ] : Scanner\22 Power & Control: sds 01-29 Function

[ 22-6-021 Set the NVD to default in the RAM of the scanner ]

Purpose Set the NVD to default in the RAM of the scanner.

Check

Remarks All service related variables (parameters, adjustments, etc.) are set to default.
You must do:
- a restore, or
- all the adjustments.

09/12/2009 107
[ 22-6-024 Turn ON the scanner into sleep mode ] : Scanner\22 Power & Control: sds 01-29 Function

[ 22-6-024 Turn ON the scanner into sleep mode ]

Purpose Turn ON the scanner into sleep mode

Check

Remarks

09/12/2009 108
[ 01-8-001 Display / set the life time of the photoconductor (in linear meters)] : Engine\01 Photoconductor: sds 01-29 Function

[ 01-8-001 Display / set the life time of the photoconductor (in linear
meters)]

Description Display / Reset the life time of the photoconductor in linear meters.

Value Range: 0 ... 99,999,999 lm

Default: 0

Remarks

09/12/2009 109
[ 02-6-001 Activate the charge unit HV-power supply (CHSUPEN 22PBA04) ] : Engine\02 Charging: sds 01-29 Function

[ 02-6-001 Activate the charge unit HV-power supply (CHSUPEN

22PBA04) ]

Warning
Remove the gear of the magnet roller of the developing unit to prevent system polution.

Purpose To check the correct function of the charging (22PBA04 - CHGHV).

Check On 22PBA04: TP2 to TP5

CHGSUP ON: 0,9 to 1,1V DC
See: 22 Power & Control - Component locator - The components of the High
Voltage Supply; 22PBA04.

Remarks Active functions during this test:

DRIMORL ON
CHGSUPEN ON
CHGERA ON
CONFAN ON
CONBIAS ON

09/12/2009 110
[ 02-8-001 Display / set the life time of the charge corona wire (in linear meters) ] : Engine\02 Charging: sds 01-29 Function

[ 02-8-001 Display / set the life time of the charge corona wire (in
linear meters) ]

Description Display / set the life time of the charge corona wire in linear meters

Value Range: 0 ... 99,999,999 lm

Default: 0

Remarks

09/12/2009 111
[ 02-8-002 Display / set the life time of the charge corona unit (in linear meters) ] : Engine\02 Charging: sds 01-29 Function

[ 02-8-002 Display / set the life time of the charge corona unit (in
linear meters) ]

Description Display / set the life time of the charge corona unit in linear meters

Value Range: 0 ... 99,999,999 lm

Default: 0

Remarks Grid wires are not replaced by the technician. Only the compleet unit.

09/12/2009 112
[ 04-0-002 Error counters ] : Engine\04 Printhead: sds 01-29 Function

[ 04-0-002 Error counters ]

Purpose
The purpose of this test is to show the error counter values, except the permanent errors
(PE).

Description
Displayed are:
- the error code
- the error message
- the error counter

The numbers are counted since the last service visit.

Note:
After each service visit the counters must be reset via SDS test 31.

09/12/2009 113
[ 04-1-003 Adjust the light intensity for average line / text prints ] : Engine\04 Printhead: sds 01-29 Function

[ 04-1-003 Adjust the light intensity for average line / text prints ]

Description Light intensity setting of the printhead LEDs for line / text prints.
Display / Set

Value Range: 10 ... 168

Default: 36

Remarks Adjustment description :

Adjustments: Adjust the light intensity for average line / text prints.

09/12/2009 114
[ 04-1-004 Adjust the extra light intensity for darker prints (poster mode) ] : Engine\04 Printhead: sds 01-29 Function

[ 04-1-004 Adjust the extra light intensity for darker prints (poster
mode) ]

Description Adjust the extra light intensity for darker prints (poster mode)

Value Range: 4 ... 40

Default: 12

Remarks Adjustment description:

Adjustments: Adjust the extra light intensity for darker prints (poster mode).

09/12/2009 115
[ 04-1-005 Adjust the light intensity of the left print head unit ] : Engine\04 Printhead: sds 01-29 Function

[ 04-1-005 Adjust the light intensity of the left print head unit ]

Description Adjust the light intensity of the left print head unit

Value Range: 50 ... 200

Default: 100

Remarks Adjustment description:

Adjust the light intensity of the left and right side print head.

09/12/2009 116
[ 04-1-007 Adjust the light intensity of the right print head unit ] : Engine\04 Printhead: sds 01-29 Function

[ 04-1-007 Adjust the light intensity of the right print head unit ]

Description Adjust the light intensity of the right print head unit

Value Range: 50 ... 200

Default: 100

Remarks Adjustment description:

Adjust the light intensity of the left and right side print head.

09/12/2009 117
[ 04-1-008 Adjust the horizontal alignment of the left and middle print head ] : Engine\04 Printhead: sds 01-29 Function

[ 04-1-008 Adjust the horizontal alignment of the left and middle

print head ]

Description Adjust the alignment between the left and middle print head.
The left print head (PHD1) is shifted.

Value Range: 1 ... 510

Default: 1
30 points is about 1mm shift

Remarks Adjustment procedure, see :

Adjust the vertical and horizontal alignment of the print head.

09/12/2009 118
[ 04-1-009 Adjust the horizontal alignment of the right and middle print head ] : Engine\04 Printhead: sds 01-29 Function

[ 04-1-009 Adjust the horizontal alignment of the right and middle

print head ]

Description Adjust the horizontal alignment between the right and middle print head.
The right side print head is shifted.

Value Range: 1 ... 123

Default: 1
30 points is about 1mm shift

Remarks Adjustment procedure, see :

Adjust the vertical and horizontal alignment of the print head.

09/12/2009 119
[ 04-1-010 Adjust the vertical alignment of the left print head ] : Engine\04 Printhead: sds 01-29 Function

[ 04-1-010 Adjust the vertical alignment of the left print head ]

Description Adjust the vertical alignment of the print head

Value Range; 0 ... 126

Default: 0

Remarks Adjustment procedure, see :

Adjust the vertical and horizontal alignment of the print head.

09/12/2009 120
[ 04-1-011 Adjust the vertical alignment of the middle print head ] : Engine\04 Printhead: sds 01-29 Function

[ 04-1-011 Adjust the vertical alignment of the middle print head ]

Description Adjust the vertical alignment of the middle print head

Value Range: 0 ... 510

Default: 0

Remarks Adjustment procedure, see :

Adjust the vertical and horizontal alignment of the print head.

09/12/2009 121
[ 04-1-012 Adjust the vertical alignment of the right print head ] : Engine\04 Printhead: sds 01-29 Function

[ 04-1-012 Adjust the vertical alignment of the right print head ]

Description Adjust the vertical alignment of the right print head

Value Range: 0 ... 126

Default: 0

Remarks Adjustment procedure, see :

Adjust the vertical and horizontal alignment of the print head.

09/12/2009 122
[ 04-1-016 Enable / disable the encoder in combination with test 54 ] : Engine\04 Printhead: sds 01-29 Function

[ 04-1-016 Enable / disable the encoder in combination with test 54

]

Description Enable / disable the encoder in combination with test print 54

Value 0 = disable
1 = enable

Remarks The settings are not stored in the eeprom.

09/12/2009 123
[ 04-1-018 Display the firmpack version of the Printhead interface ] : Engine\04 Printhead: sds 01-29 Function

[ 04-1-018 Display the firmpack version of the Printhead interface ]

Description Display the current software version of the Printhead interface

Value as a version number e.g. 1,2,3

Remarks

09/12/2009 124
[ 04-9-001 Display the temperatuur of the print head NTC (PHDNTC 04R1) in 0.1 ºC ] : Engine\04 Printhead: sds 01-29

[ 04-9-001 Display the temperatuur of the print head NTC (PHDNTC

04R1) in 0.1 ºC ]

Description Display the temperature and elapsed time of the print head NTC (PHDNTC 04R1) in 0.1 ºC

Value Cold printer: e.g 210 in 0.1 ºC

In RUN mode:

Remarks Test active during a run of 3 (test) prints. Result is displayed.

09/12/2009 125
[ 04-9-002 Display the print head assembly status ] : Engine\04 Printhead: sds 01-29 Function

[ 04-9-002 Display the print head assembly status ]

Description Display the print head assembly status

Value LVL_ PHD_ASSEMBLY_INSTALLED : Correct installed printhead interface.

LVL_PHD_BLANK: Print head interface PBA installed without adjustment.
LVL_PHD_ADJUSTMENT_SUCCESFUL: Print head successfull passed the print head tool
LVL_PHD_ADJUSTMENT_FAILED: Print head failed to pass the print head tool
LVL_PHD_ADJUSTMENT_STARTED: Print head enters the tool but the adjustment procedure is not
finished.

Remarks

09/12/2009 126
[ 04-9-003 Display the contents of the print head FPGA status register of the last print ] : Engine\04 Printhead: sds 01-29 Function

[ 04-9-003 Display the contents of the print head FPGA status

register of the last print ]

Description Display the contents of the print head FPGA status register of the last print.

Value LVL_PRINTHEAD_OK:
LVL_PRINTHEAD_ERROR:

Remarks In case no print is made after switching on the printer the FPGA status word
should be 83.
In casea print is made the FPGA status word should be 87.

09/12/2009 127
[ 05-0-002 Error counters ] : Engine\05 Developing: sds 01-29 Function

[ 05-0-002 Error counters ]

Purpose
The purpose of this test is to show the error counter values, except the permanent errors
(PE).

Description
Displayed are:
- the error code
- the error message
- the error counter

The numbers are counted since the last service visit.

Note:
After each service visit the counters must be reset via SDS test 31.

09/12/2009 128
[ 05-1-001 Display the setpoint of the developer mixture ] : Engine\05 Developing: sds 01-29 Function

[ 05-1-001 Display the setpoint of the developer mixture ]

Description Show the reference value (in Volt) for the developer mixture.

Value Range: 0 ... 15.000

Default: 8.000

Remarks 1. The set-point value of the sensor is adjusted by the factory.

2. The value is adjusted by service according to the description:
Adjustment: Adjustment procedure new developer DEVTONCONSE 05B1.

09/12/2009 129
[ 05-1-002 Display the sensitivity of the developer mixture sensor (DEVCONSE 05B1) ] : Engine\05 Developing: sds 01-29 Function

[ 05-1-002 Display the sensitivity of the developer mixture sensor

(DEVCONSE 05B1) ]

Description Shows the sensitivity value (mV) of the toner sensor.

Value Range: 100 ... 1000

Default: 300

Remarks 1. The sensitivity value of the sensor is adjusted by the factory.

2. The value is set by service according to the description:
Adjustment: Adjustment procedure new developer DEVTONCONSE 05B1.

09/12/2009 130
[ 05-1-004 Enable / disable in the Installation test: Adjustment procedure new developer ] : Engine\05 Developing: sds 01-29 Function

[ 05-1-004 Enable / disable in the Installation test: Adjustment

procedure new developer ]

Description Enable / disable the Installation test: Adjustment procedure new developer.
If enabled the test 05-7-001 is activated during the installation.

Value Disable
Enable

Remarks The parameter is set automatically to 'disabled' after the installation test is
activated.

09/12/2009 131
[ 05-2-001 Check the toner level switch of the supply unit (DEVTONSUPSW 05S1) ] : Engine\05 Developing: sds 01-29 Function

[ 05-2-001 Check the toner level switch of the supply unit

(DEVTONSUPSW 05S1) ]

Warning: Remove the gear of the magnet roller of the developer unit to prevent the system for
pollution.

Condition Toner unit is full.

SDS message: toner present

Action Place a (strong) magnet against the outside of the [ reed ] switch

Check Check the SDS message: toner not present

09/12/2009 132
[ 05-4-001 Activate the HV-power supply for the bias and the clean unit (DEVSUPEN 22PBA04) ] : Engine\05 Developing: sds 01-29 Fun

[ 05-4-001 Activate the HV-power supply for the bias and the clean
unit (DEVSUPEN 22PBA04) ]

Purpose To check the correct function of the: (22PBA04)

bias high voltage BIASHV

cleaning high voltage CLEANHV

Check On 22PBA04:
DEVBIASHV TP2 to TP1: -600V DC
DEVCLEHV TP2 to TB2: -460V DC
See: 22 Power & Control - Component locator - The components of the High
Voltage Supply; 22PBA04.

Remarks Check DEVBIASHV on the developer roller.

Check DEVCLEHV on the developer unit.

09/12/2009 133
[ 05-6-001 Recover the too low toner level of the developer ] : Engine\05 Developing: sds 01-29 Function

[ 05-6-001 Recover the too low toner level of the developer ]

Caution
During the test, the following functions are active: charge, developer, drive, ozone exhaust fan.

Purpose Recover the toner concentration while no prints are made.

The toner is supplied when it is necessary. This is measured by the [ Toner
concentration sensor ] (DEVCONSE 05B1).

Check Check the toner concentration by the print quality. Use the test print 51.

Remarks The control timing is the same like a normal print run.
The test automatically stops after 10 minutes.
After the test is stopped, the ozone exhaust fan remains active during 6 seconds.

09/12/2009 134
[ 05-6-002 Recover the developer layer equal in the developer unit ] : Engine\05 Developing: sds 01-29 Function

[ 05-6-002 Recover the developer layer equal in the developer unit ]

Warning
Before you start the test, check first the correct function of the charging supply (CHGSUPEN) and
the bias supply (DEVSUPEN).
During the test, the toner concentration limits are not checked.
There are no errors / warnings reported.

Caution
During the test, the following functions are activated:
charge, drive, developer unit, ozone fan.

Purpose Divide the developer equal in the developer unit while no prints are made and no
toner is supplied.

Check Open the top cover of the developer unit and check if the developer is divided
equal in the whole unit.

Remarks The control timing is the same like a normal print run.
The test automatically stops after 10 minutes.
After the test is stopped, the ozone exhaust fan remains active during 6 seconds.

09/12/2009 135
[ 05-6-003 Activate the toner supply motor (DEVTONSUPMO 05M1) ] : Engine\05 Developing: sds 01-29 Function

[ 05-6-003 Activate the toner supply motor (DEVTONSUPMO 05M1)

]

Purpose Check in the toner reservoir the operating of:

- the toner supply motor DEVTONSUPMO (05M1) and
- the toner supply switch DEVSUPSW (05S1)

Check Check:
- if the supply motor runs
- if the supply switch indicates information
- [ toner present ]
- [ toner not present ]

Remarks The test automatically stops after 10 seconds.

09/12/2009 136
[ 05-7-001 Adjustment procedure new developer ] : Engine\05 Developing: sds 01-29 Function

[ 05-7-001 Adjustment procedure new developer ]

Warning
Only run the test with new developer.

Caution
During the test, the following functions are active: charge, drive, developer,
ozone exhaust fan.

Purpose To set the concentration set-point for the concentration sensor (DEVCONSE
05B1) for new developer.

Check No check

Action Conform the description:

Adjustment: Adjustment procedure new developer DEVTONCONSE 05B1.

Remarks The test takes about 4 minutes.

After the test is stopped, the ozone exhaust fan remains active during 6 seconds.

This test is also part of the installation test.

09/12/2009 137
[ 05-8-001 Display / set the life time of the developer (in linear meters) ] : Engine\05 Developing: sds 01-29 Function

[ 05-8-001 Display / set the life time of the developer (in linear
meters) ]

Description Display / set the life time of the developer in linear meters

Value Range: 0 ... 99,999,999 lm

Default: 0

Remarks The developer installation will automatically set this value to 0.

09/12/2009 138
[ 05-9-001 Display the values of the toner sensor (DEVCONSE 05B1) ] : Engine\05 Developing: sds 01-29 Function

[ 05-9-001 Display the values of the toner sensor (DEVCONSE

05B1) ]

Description
Display the values of:
the set-point of the developer concentration sensor DEVCONSE 05B1.
the sensitivity value of the toner concentration sensor DEVTONSE 05B1

Display
DEVCONSP
DEVCONSE (in mV)
Elapsed time

Remark
The test automatically stops after 10 minutes.
After the test is stopped, the ozone exhaust fan remains active during 6 seconds.

09/12/2009 139
[ 06-6-001 Activate the HV-power supply of the transfer unit (TRASUPEN 22PBA04) ] : Engine\06 Transfer: sds 01-29 Function

[ 06-6-001 Activate the HV-power supply of the transfer unit

(TRASUPEN 22PBA04) ]

Warning 1
First do the separation test 15-6-001.

Warning 2
Remove the magnet roller gear of the developer unit to prevent toner polution.
Turn it also a 3/4 revolution clockwise.

Purpose To check the correct function of the transfer (22PBA04 - TRAHV)

Check On 22PBA04: TP2 to TP4

TRASUP ON: -0,65 to -0,4V DC
See: 22 Power & Control - Component locator - The components of the High
Voltage Supply; 22PBA04.

Remarks Active functions during this test:

(The transfer and the separation function are not switched ON at the same time!)
TRASUPEN ON (for a period of 3 sec. and beeper on) and then:
PTRSEPSUPEN ON (for a period of 3.3 sec.).

CHGERA ON
DRIMORL ON
CONFAN ON

- This test automatically stops after 1 minute

- After the test is deactivated the ozon exhaust fan stays active for 6 sec.

09/12/2009 140
[ 06-8-001 Display / set the life time of the transfer corona wire (in linear meters) ] : Engine\06 Transfer: sds 01-29 Function

[ 06-8-001 Display / set the life time of the transfer corona wire (in
linear meters) ]

Description Display / set the lifetime of the transfer corona wire in linear meters.

Value Range: 0 ... 99,999,999 lm

Default: 0

Remarks

09/12/2009 141
[ 07-4-001 Activate the led's of the discharge unit (DCH 07PBA02) ] : Engine\07 Cleaning/Discharge: sds 01-29 Function

[ 07-4-001 Activate the led's of the discharge unit (DCH 07PBA02) ]

Purpose To check the led's of the discharge function (DCH 07PBA02)

Condition -

Check Visual check

09/12/2009 142
[ 07-8-001 Display / set the life time of the cleaning blade (in linear meters) ] : Engine\07 Cleaning/Discharge: sds 01-29 Function

[ 07-8-001 Display / set the life time of the cleaning blade (in linear
meters) ]

Description Display / set the lifetime of the cleaning blade in linear meters.

Value Range: 0 ... 99,999,999 lm

Default: 0

Remarks

09/12/2009 143
[ 08-0-002 Error counters ] : Engine\08 Fusing: sds 01-29 Function

[ 08-0-002 Error counters ]

Purpose
The purpose of this test is to show the error counter values, except the permanent errors
(PE).

Description
Displayed are:
- the error code
- the error message
- the error counter

The numbers are counted since the last service visit.

Note:
After each service visit the counters must be reset via SDS test 31.

09/12/2009 144
[ 08-4-001 Activate the left and right fuser fans (FUSFANL/R 08M1/2) ] : Engine\08 Fusing: sds 01-29 Function

[ 08-4-001 Activate the left and right fuser fans (FUSFANL/R

08M1/2) ]

Purpose To check the left and right fuser fan (FUSFANL/R)

FIXFANL/R ON/OFF

Condition -

Check Visual check

09/12/2009 145
[ 08-6-001 Activate the front and rear fuser heaters (FUSHEF/R 08E1/2) ] : Engine\08 Fusing: sds 01-29 Function

[ 08-6-001 Activate the front and rear fuser heaters (FUSHEF/R

08E1/2) ]

Purpose To check the front and rear fuser heater (FUSHEF/R).

Check Indication of the NTC1 ... 5 and NTCREFL in ºC

Remarks The test stops after 1 min.

09/12/2009 146
[ 08-9-001 Display the values of the fuser NTC 1-5,

[ 08-9-001 Display the values of the fuser NTC 1-5,

absorber NTC 6 (FUSNTC1-6 08R1-6) (in 0.1 ºC) ]

Purpose Display the value of the fuser NTC 1... 5 and NTCREFL in in 0.1 ºC

Check Indication of the NTC1 ... 5 and NTCREFL in 0.1 ºC

Remarks Make a run of copies.

09/12/2009 147
[ 12-0-002 Error counters ] : Engine\12 Paper Roll Drawers: sds 01-29 Function

[ 12-0-002 Error counters ]

Purpose
The purpose of this test is to show the error counter values, except the permanent errors
(PE).

Description
Displayed are:
- the error code
- the error message
- the error counter

The numbers are counted since the last service visit.

Note:
After each service visit the counters must be reset via SDS test 31.

09/12/2009 148
[ 12-1-001 Installation test: Adjust the leading edge position of roll 1 and roll 2

[ 12-1-001 Installation test: Adjust the leading edge position of roll

1 and roll 2
(in 0.1 mm)]

Description Adjust the leading edge position of roll 1 and 2 (in 0.1 mm) during the installation
of the TDS300.

Value Range: -100 ... 0

Default: 0

Remarks This test is part of the installation test.

Description adjustment procedure :
Adjustments: Adjustment procedure trailing edge position between the first and
the following prints in a run.

09/12/2009 149
[ 12-1-003 Adjust the image in the width direction of roll 1 (in 0.1 mm) ] : Engine\12 Paper Roll Drawers: sds 01-29 Function

[ 12-1-003 Adjust the image in the width direction of roll 1 (in 0.1
mm) ]

Description Adjust the image in the width direction of roll 1 (in 0.1 mm)

Value Range: -100 ... +100

Default: 0

Increased value: the image moves to the left.

Decreased value: the image moves to the right.

Remarks Description adjustment procedure :

Adjustments: Adjustment procedure of the image position in the width direction for
roll 1 or roll 2 (in 0.1 mm).

09/12/2009 150
[ 12-1-004 Adjust the cutting length for a new (approx. 175mtr.) roll 1 (in 0.1 mm) ] : Engine\12 Paper Roll Drawers: sds 01-29 Function

[ 12-1-004 Adjust the cutting length for a new (approx. 175mtr.) roll
1 (in 0.1 mm) ]

Description Adjust the cutting length for a new roll 1(in 0.1 mm)

Value Range: -1000 ... +1000

Default: -200 (in 0.1 mm)
Increase value: paper length shorter
Decease value: paper length longer

Remarks Start with a new roll. The tolerances for a used roll are always decreasing.

09/12/2009 151
[ 12-1-006 Adjust the cutting length for a new (approx. 175mtr.) roll 2 (in 0.1 mm) ] : Engine\12 Paper Roll Drawers: sds 01-29 Function

[ 12-1-006 Adjust the cutting length for a new (approx. 175mtr.) roll
2 (in 0.1 mm) ]

Description Adjust the cutting length for a new roll 2 (in 0.1 mm)

Value Range: -1000 ... +1000

Default: -200
Increase value: paper length shorter
Decease value: paper length longer

Remarks Start with a new roll. The tolerances for a used roll are always decreasing.

09/12/2009 152
[ 12-1-041 Adjust the image in the width direction of roll 2 (in 0.1 mm) ] : Engine\12 Paper Roll Drawers: sds 01-29 Function

[ 12-1-041 Adjust the image in the width direction of roll 2 (in 0.1
mm) ]

Description Adjust the image in the width direction of roll 2 (in 0.1 mm)

Value Range: -100 ... +100

Default: 0

Remarks Description adjustment procedure

Adjustments: Adjustment procedure of the image position in the width direction for
roll 1 or roll 2 (in 0.1 mm).:

09/12/2009 153
[ 12-1-050 Adjust the cutting length for prints longer than A0 (in 0.1 mm) ] : Engine\12 Paper Roll Drawers: sds 01-29 Function

[ 12-1-050 Adjust the cutting length for prints longer than A0 (in 0.1
mm) ]

Description Adjust the cutting length for prints longer than A0 (in 0.1 mm)

Value Range: 0 ... 38

Default: 19

Remarks Description adjustment procedure :

Adjustments: Adjust the cutting lenght for prints longer than A0.

09/12/2009 154
[ 12-1-051 Adjust a longer or shorter trailing edge length of roll 1 (on request customer) (in mm): Engine\12 Paper Roll Drawers: sds 01-2

[ 12-1-051 Adjust a longer or shorter trailing edge length of roll 1

(on request customer) (in mm)

Description Adjust the cutting length for prints longer than A0 (in mm)

Value Range: -10 ... + 10

Default: 0

Remarks Adjustment procedure

09/12/2009 155
[ 12-1-052 Adjust a longer or shorter trailing edge length of roll 2 (on request customer) (in mm) ] : Engine\12 Paper Roll Drawers: sds 01

[ 12-1-052 Adjust a longer or shorter trailing edge length of roll 2

(on request customer) (in mm) ]

Description Adjust a longer or shorter trailing edge length of roll 2 (on request customer) (in
mm)

Value Range: -10 ... + 10

Default: 0

Remarks Adjustment procedure

09/12/2009 156
[ 12-1-053 Enable / disable in the installation test: Adjustment procedure leading edge position for the roll 1 and roll 2 (PRDLEADSE 12B

[ 12-1-053 Enable / disable in the installation test: Adjustment

procedure leading edge position for the roll 1 and roll 2
(PRDLEADSE 12B3) ]

Description Enable / disable in the Installation test:

Test SDS 12-7-008, Adjustment procedure leading edge position for the roll 1 and
roll 2 (PRDLEADSE 12B3).

Value

Remarks - The test 12-7-008 is also part of the installation test.

- This sds test (12-1-053) is automatically set to ["disabled"] after the sds test
12-7-008 is executed.

09/12/2009 157
[ 12-1-054 Enable / disable in the installation test: Adjustment procedure of the paper cut length roll 1 ] : Engine\12 Paper Roll Drawers: s

[ 12-1-054 Enable / disable in the installation test: Adjustment

procedure of the paper cut length roll 1 ]

Description Enable / disable in the installation test:

Test SDS 12-7-009, Adjustment procedure of the paper cut length roll 1.

Value

Remarks - The test 12-7-009 is also part of the installation test.

- This sds test (12-1-054) is automatically set to ["disabled"] after the sds test
12-7-009 is executed.

09/12/2009 158
[ 12-1-055 Enable / disable 12" paper alignment with A2 marker ] : Engine\12 Paper Roll Drawers: sds 01-29 Function

[ 12-1-055 Enable / disable 12" paper alignment with A2 marker ]

Description 12" paper alignment with A2 marker

To be used if image adjustment for 12" media width fails

Value 0 = Disable
1 = Enable

Remarks See adjustment

09/12/2009 159
[ 12-2-003 Check of the knife sensor at the right hand side (PRDKNIPOSSER 12B2) ] : Engine\12 Paper Roll Drawers: sds 01-29 Functio

[ 12-2-003 Check of the knife sensor at the right hand side

(PRDKNIPOSSER 12B2) ]

Description Check of the knife sensor at the right hand side (PRDKNIPOSSER 12B2)

Value Active: knife stopped at the right hand side.

Not active: knife stopped at the left hand side.

Remarks

09/12/2009 160
[ 12-2-004 Check of the knife sensor at the left hand side PRDKNIPOSSEL 12B1) ] : Engine\12 Paper Roll Drawers: sds 01-29 Function

[ 12-2-004 Check of the knife sensor at the left hand side

PRDKNIPOSSEL 12B1) ]

Description Check of the knife sensor at the left hand side (PRDKNIPOSSEL 12B1)

Value Active: knife stopped at the left hand side.

Not active: knife stopped at the right hand side.

Remarks

09/12/2009 161
[ 12-2-005 Check of the lead sensor (PRDLEADSE 12B3) ] : Engine\12 Paper Roll Drawers: sds 01-29 Function

[ 12-2-005 Check of the lead sensor (PRDLEADSE 12B3) ]

Description Check of the lead sensor (PRDLEADSE 12B3)

Value Paper present: sensor activated.

Paper not present: sensor not activated.

Remarks

09/12/2009 162
[ 12-2-006 Check of the door switch of the roll unit (PRDDOORSW1 12S1) ] : Engine\12 Paper Roll Drawers: sds 01-29 Function

[ 12-2-006 Check of the door switch of the roll unit (PRDDOORSW1

12S1) ]

Description Check of the door switch of the (upper) roll unit (PRDDOORSW1 12S1)

Value Door closed

Door open

Remarks

09/12/2009 163
[ 12-2-009 Check of the paper roll 1 empty sensor (PRDRUNSE1 12B4) ] : Engine\12 Paper Roll Drawers: sds 01-29 Function

[ 12-2-009 Check of the paper roll 1 empty sensor (PRDRUNSE1

12B4) ]

Description Check of the paper roll 1 empty sensor (PRDRUNSE1 12B4)

Value Pulsdisk in the upper roll unit.

Pulses are generated: upper roll not empty

Pulses are NOT genertated: upper roll empty

Remarks Check: Rotate the pullsdisk in the upper roll compartment.

09/12/2009 164
[ 12-2-010 Check of the lower door switch of the roll unit (PRDDOORSW2 12S2) ] : Engine\12 Paper Roll Drawers: sds 01-29 Function

[ 12-2-010 Check of the lower door switch of the roll unit

(PRDDOORSW2 12S2) ]

Description Check of the door switch of the (lower) roll unit (PRDDOORSW2 12S2)

Value Door closed

Door open

Remarks

09/12/2009 165
[ 12-2-011 Check of the paper roll 2 empty sensor (PRDRUNSE2 12B5) ] : Engine\12 Paper Roll Drawers: sds 01-29 Function

[ 12-2-011 Check of the paper roll 2 empty sensor (PRDRUNSE2

12B5) ]

Description Check of the paper roll 2 empty sensor (PRDRUNSE2 12B5)

Value Pulsdisk in the lower roll unit.

Pulses are generated: lower roll not empty

Pulses are NOT genertated: lower roll empty

Remarks Check: Rotate the pullsdisk in the lower roll compartment.

09/12/2009 166
[ 12-6-001 Activate the knife motor (PRDKNIMO 12M3) ] : Engine\12 Paper Roll Drawers: sds 01-29 Function

[ 12-6-001 Activate the knife motor (PRDKNIMO 12M3) ]

Purpose Activate the knife motor (PRDKNIMO 12M3)

Check Test active: knife transported to the other side of the roll unit.
As the knife sensor is activated the test is stopped.

Remarks

09/12/2009 167
[ 12-6-002 Activate the paper feed motor of roll 1 (PRDFEDMO1 12M1)] : Engine\12 Paper Roll Drawers: sds 01-29 Function

[ 12-6-002 Activate the paper feed motor of roll 1 (PRDFEDMO1

12M1)]

Purpose Activate the paper feed motor of roll 1 (PRDFEDMO1 12M1)

Check Functional test of the upper feed motor.

Options:
- Forward normal mode
- Backward normal mode

Remarks

09/12/2009 168
[ 12-6-042 Activate the paper feed motor of roll 2 (PRDFEDMO2 12M2) ] : Engine\12 Paper Roll Drawers: sds 01-29 Function

[ 12-6-042 Activate the paper feed motor of roll 2 (PRDFEDMO2

12M2) ]

Purpose Activate the paper feed motor of roll 2 (PRDFEDMO2 12M2)

Check Functional test of the lower feed motor.

Options:
- Forward normal mode
- Backward normal mode

Remarks

09/12/2009 169
[ 12-6-043 Cut a 841 mm sheet of roll 1 ] : Engine\12 Paper Roll Drawers: sds 01-29 Function

[ 12-6-043 Cut a 841 mm sheet of roll 1 ]

Purpose Cut a 841 mm sheet of roll 1

Check

Remarks

09/12/2009 170
[ 12-7-008 Installation test: Adjustment procedure of the trailing edge position between the first and the following prints in a run: Engine\1

[ 12-7-008 Installation test: Adjustment procedure of the trailing

edge position between the first and the following prints in a run

Purpose Adjustment procedure of the trailing edge position between the first and the
following prints in a run.
Only when the paper is started and PDRLEADSE 12B3 is free.

Value The value is stored in the SDS test 12-1-001.

Remarks This test is also part of the installation test.

Description adjustment procedure :
Adjustments: djustment procedure trailing edge position between the first and the
following prints in a run.

09/12/2009 171
[ 12-7-009 Adjustment procedure of the paper cut length roll 1 ] : Engine\12 Paper Roll Drawers: sds 01-29 Function

[ 12-7-009 Adjustment procedure of the paper cut length roll 1 ]

Purpose Adjustment procedure of the paper cut length roll 1

Value

Remarks Before you start: The PRDLEADSE sensor must be correct adjusted (sds test
12-7-008).
This test is part of the Transporter installation test.

09/12/2009 172
[ 12-7-010 Adjustment procedure of the paper cut length roll 2 ] : Engine\12 Paper Roll Drawers: sds 01-29 Function

[ 12-7-010 Adjustment procedure of the paper cut length roll 2 ]

Purpose Adjustment procedure of the paper cut length roll 2

Value

Remarks Before you start: The PRDLEADSE sensor must be correct adjusted (sds test
12-7-008).
This test is part of the Transporter installation test.

09/12/2009 173
[ 12-9-001 Display the length of the last print (in 0.1 mm) ] : Engine\12 Paper Roll Drawers: sds 01-29 Function

[ 12-9-001 Display the length of the last print (in 0.1 mm) ]

Purpose Display the length of the last print (in 0.1 mm)

Check

Remarks

09/12/2009 174
[ 12-9-003 Display the measured time to cut the last print material (in msec) ] : Engine\12 Paper Roll Drawers: sds 01-29 Function

[ 12-9-003 Display the measured time to cut the last print material
(in msec) ]

Purpose Display the measured time to cut the last print material (in msec)

Check

Remarks

09/12/2009 175
[ 15-0-002 Display the error counters of the paper transport ]: Engine\15 Paper Transport: sds 01-29 Function

[ 15-0-002 Display the error counters of the paper transport ]

Purpose
The purpose of this test is to show the error counter values, except the permanent errors
(PE).

Description
Displayed are:
- the error code
- the error message
- the error counter

The numbers are counted since the last service visit.

Note:
After each service visit the counters must be reset via SDS test 31.

09/12/2009 176
[ 15-1-001 Adjust the leading edge position (PTRSYNSE 15B2) for the roll1, roll 2 and manual feed (in 0.1 mm) ] : Engine\15 Paper Trans

[ 15-1-001 Adjust the leading edge position (PTRSYNSE 15B2) for

the roll1, roll 2 and manual feed (in 0.1 mm) ]

Description Adjust the leading edge position (PTRSYNSE 15B2) for the roll 1, roll 2 and
manual feed (in 0.1 mm)

Value Range: -340 ... 260

Default: 0 ( x 0.1 mm)

Remarks Description adjustment procedure :

Adjustments: Adjustment procedure leading edge position for the roll 1, roll 2 and
manual feed.

09/12/2009 177
[ 15-1-003 Adjust the image in the width direction, for the manual feed (in 0.1 mm) ] : Engine\15 Paper Transport: sds 01-29 Function

[ 15-1-003 Adjust the image in the width direction, for the manual
feed (in 0.1 mm) ]

Description Adjust the image in the width direction, for the manual feed (in 0.1 mm)

Value Range: -100 ... +100

Default: 0 ( x 0.1 mm)

Remarks Description adjustment procedure :

Adjust the image position in the width direction for manual feed (in 0.1 mm).

09/12/2009 178
[ 15-1-004 Enable / disable in the installation test: Adjustment of the leading edge position (PTRSYNSE 15B2)] : Engine\15 Paper Transp

[ 15-1-004 Enable / disable in the installation test: Adjustment of

the leading edge position (PTRSYNSE 15B2)]

Description Enable / disable in the installation test:

Adjustment of the leading edge position for the roll 1, roll 2 and manual feed.

Value The calculated value is stored in the SDS test 15-1-001.

Remarks This test is set to "disable" after the installation test is activated.
This test is part of the installation test.

09/12/2009 179
[ 15-1-005 Adjust the leading edge position (on request customer) (in mm) ] : Engine\15 Paper Transport: sds 01-29 Function

[ 15-1-005 Adjust the leading edge position (on request customer)

(in mm) ]

Description Adjust the leading edge position (on request customer) (in mm)

Value Range: 0 ... 10

Default: 0

Remarks This adjustment has no influence on the test prints made by SDS.

09/12/2009 180
[ 15-2-001 Check the paper input sensor (PTRINSE 15B1) ] : Engine\15 Paper Transport: sds 01-29 Function

[ 15-2-001 Check the paper input sensor (PTRINSE 15B1) ]

Condition Paper present: sensor activated.

Paper not present: sensor not activated

Action Feed copy material

Check

09/12/2009 181
[ 15-2-003 Check the switch of the manual feed table (PTRDEFSW 15S1) ] : Engine\15 Paper Transport: sds 01-29 Function

[ 15-2-003 Check the switch of the manual feed table (PTRDEFSW

15S1) ]

Condition Check the switch of the manual feed table (PTRDEFSW 15S1)

Active: manual feed table in the lower position.

Not active: manual feed table not in the lower position.

Action Lower the manual feed table.

Check

09/12/2009 182
[ 15-2-004 Check the synchronisation sensor (PTRSYNSE 15B2) ] : Engine\15 Paper Transport: sds 01-29 Function

[ 15-2-004 Check the synchronisation sensor (PTRSYNSE 15B2) ]

Condition Check the synchronisation sensor (PTRSYNSE 15B2)

Paper present: sensor detects copy material.

Paper not present: sensor detects no copy material.

Action

Check

09/12/2009 183
[ 15-2-005 Check the paper output sensor of the fuser (PTROUTSE 15B3) ] : Engine\15 Paper Transport: sds 01-29 Function

[ 15-2-005 Check the paper output sensor of the fuser (PTROUTSE

15B3) ]

Condition Check the paper output sensor of the fuser (PTROUTSE 15B3)

Paper present: sensor detects copy material.

Paper not present: sensor detects no copy material.

Action

Check

09/12/2009 184
[ 15-4-001 Check the clutch of the syncronisation roller (PTRSYNCL 15Y1) ] : Engine\15 Paper Transport: sds 01-29 Function

[ 15-4-001 Check the clutch of the syncronisation roller (PTRSYNCL

15Y1) ]

Purpose Check the clutch of the syncronisation roller (PTRSYNCL 15Y1)

Condition
-

Check
-

09/12/2009 185
[ 15-6-001 Activate the HV power supply of the separation unit (PTRSEPSUPEN 12PBA04) ] : Engine\15 Paper Transport: sds 01-29 Fun

[ 15-6-001 Activate the HV power supply of the separation unit

(PTRSEPSUPEN 12PBA04) ]

Warning
Remove the gear of the magnet roller of the developing unit to prevent system polution.
Turn it a 1/2 revolution counter clockwise.

Purpose To check the correct function of the separation (22PBA04 - PTRSEPHV).

Check On 22PBA04: TP2 to TP3

PTRSEPSUPEN ON: 0,65 to 0,9V rms
See: 22 Power & Control - Component locator - The components of the High
Voltage Supply; 22PBA04.

Remarks Active functions during this test:

PTRSEPSUPEN ON
DRIMORL ON
CHGERA ON
CONFAN ON

09/12/2009 186
[ 15-8-001 Display / set the life time of the separation corona wire (in linear meters) ] : Engine\15 Paper Transport: sds 01-29 Function

[ 15-8-001 Display / set the life time of the separation corona wire
(in linear meters) ]

Description Display / set the lifetime of the separation corona wire in linear meters.

Value Range: 0 ... 9,999,999 lm

Default: 0

Remarks

09/12/2009 187
[ 19-2-001 Check the flap sensor of the compact output stacker (DELFLAPPOSSE 19B1) ] : Engine\19 Delivery\Copy output stacker: sds

[ 19-2-001 Check the flap sensor of the compact output stacker

(DELFLAPPOSSE 19B1) ]

Condition Check the flap sensor of the compact output stacker (DELFLAPPOSSE 19B1)

Active: No original: Flap in the home position.

Not active: Flap no in the home position

Action

Check

09/12/2009 188
[ 19-4-001 Activate the flap motor of the compact output stacker (DELFLAPMO 19M1) ] : Engine\19 Delivery\Copy output stacker: sds 01

[ 19-4-001 Activate the flap motor of the compact output stacker

(DELFLAPMO 19M1) ]

Purpose To check the flap motor of the Copy Output Stacker (DELFLAPMO 19M1)

DELFLAPMO ON/OFF

Condition
-

Check
Visual check if motor is active / not active

09/12/2009 189
[ 22-0-002 Error counters of the printer ] : Engine\22 Power & Control: sds 01-29 Function

[ 22-0-002 Error counters of the printer ]

Purpose
The purpose of this test is to show the error counter values, except the permanent
errors (PE).

Description
Displayed are:
- the error code
- the error message
- the error counter

The numbers are counted since the last service visit.

Note:
After each service visit the counters must be reset via SDS test 31.

09/12/2009 190
[ 22-1-001 Display the software release number of the printer ] : Engine\22 Power & Control: sds 01-29 Function

[ 22-1-001 Display the software release number of the printer ]

Description Display the software release number of the printer firmpack.

Presentation 5 /6 digits: (a)a.bb.cc (e.g. 1.15.1 = 11501).

Value Range: 1000 .... 99.99.99

Remarks

09/12/2009 191
[ 22-1-006 Display the release number of the boot software of the printer ] : Engine\22 Power & Control: sds 01-29 Function

[ 22-1-006 Display the release number of the boot software of the

printer ]

Description Display the release number of the boot software of the printer
Presentation 5 /6 digits: (a)a.bb.cc (e.g. 1.15.1 = 11501).

Value Range: 1000 .... 99.99.99

Remarks

09/12/2009 192
[ 22-1-050 Display / set the printer display for languages with a special character set ] : Engine\22 Power & Control: sds 01-29 Function

[ 22-1-050 Display / set the printer display for languages with a

special character set ]

From R1.2
Set the SDS test to '1' to display the Polish and de Czech language on the operator display.

Description Display / set the printer display to include the special character set for the Polish
and the Czech language.

Value Range: 0 or 1
Default: 0
0 = universal font
1 = universal font with the special character set for the Polish and the Czech
language.

Remarks For R1.1: no SDS test is available and the old panel display can not present the
special character set.
For R1.2: only the new display in the operator panel can display the special
character set. See the partslist.

09/12/2009 193
[ 22-1-080 Chinese paper empty print ] : Engine\22 Power & Control: sds 01-29 Function

[ 22-1-080 Chinese paper empty print ]

Description
This parameter enables/disables the printing of a blank sheet after a timeout.
This parameter is part of the Chinese paper patch to prevent bad transfer of the toner on the
paper.
Related to this parameter is parameter 22-1-081 that determines the idle time of a roll.

Value
Range: 0 or 1
Default: 0
0 = disabled
1 = enabled

09/12/2009 194
[ 22-1-081 Chinese paper idle timeout ] : Engine\22 Power & Control: sds 01-29 Function

[ 22-1-081 Chinese paper idle timeout ]

Description
This parameter determines the idle time for a roll.
If after this timeout a print is made from that roll, first a blank page of 420 mm is printed.
This parameter is part of the Chinese paper patch

Value
Units in seconds
minimum: 0
maximum: 3600
Default: ?

09/12/2009 195
[ 22-4-001 Activate the ozone fan (OZFAN 22M1) ] : Engine\22 Power & Control: sds 01-29 Function

[ 22-4-001 Activate the ozone fan (OZFAN 22M1) ]

Purpose To check the ozone fan (OZFAN 22M1)

CONFAN ON/OFF

Condition
-

Check
Visual check if fan is active / not active

09/12/2009 196
[ 22-4-002 Activate the safety releay (MAINSYNC 22PBA02) ] : Engine\22 Power & Control: sds 01-29 Function

[ 22-4-002 Activate the safety releay (MAINSYNC 22PBA02) ]

Purpose To check the safety releay (MAINSYNC 22PBA02)

CONSARL ON/OFF

Condition
-

Check
Visual check if relay active / not active

09/12/2009 197
[ 22-6-001 Set the NVD to default in the RAM of the printer ] : Engine\22 Power & Control: sds 01-29 Function

[ 22-6-001 Set the NVD to default in the RAM of the printer ]

Warning

Caution

Purpose Set the NVD to default in the RAM of the printer.

Check

Remarks All service related variables (parameters, adjustments, etc.) are set to default.
You must do:
- a restore, or
- all the adjustments.

09/12/2009 198
[ 22-6-006 Activate the copy counter ] : Engine\22 Power & Control: sds 01-29 Function

[ 22-6-006 Activate the copy counter ]

Warning

Caution

Purpose Activate the copy counter (22Y1)

Check The counter makes one pulse.

Visual check of the counter.

Remarks The test uses an input line on the board to check if the counter is connected.

09/12/2009 199
[ 22-6-007 Switch ON the low voltage supply (22PBA02) ] : Engine\22 Power & Control: sds 01-29 Function

[ 22-6-007 Switch ON the low voltage supply (22PBA02) ]

Warning

Caution

Purpose Switch ON the low voltage power supply (22PBA02)

Check Measue the output voltages:

Remarks

09/12/2009 200
[ 22-8-001 Display / set the total amount of material processed by the printer (in linear meters) ] : Engine\22 Power & Control: sds 01-29 F

[ 22-8-001 Display / set the total amount of material processed by

the printer (in linear meters) ]

Description Display / set the total amount of material processed by the printer in linear meters.

Value Range: 0 ... 99,999,999 lm

Remarks Activated in SDS test 97

09/12/2009 201
[ 22-9-002 Display the power supply frequency (in 0,1 Hz) ] : Engine\22 Power & Control: sds 01-29 Function

[ 22-9-002 Display the power supply frequency (in 0,1 Hz) ]

Purpose Display the power supply frequency (in 0,1 Hz)

The frequency is measured on the CPU IO PBA of the printer by the CONMAINSII
interupt.

Check

Remarks

09/12/2009 202
[ 23-6-001 Activate the drive motor (DRIMO 23M1) ] : Engine\23 Drive: sds 01-29 Function

[ 23-6-001 Activate the drive motor (DRIMO 23M1) ]

Warning
Activating the Main Drive Motor too long can cause OPC pollution.

Purpose Activate the drive motor (DRIMO 23M1)

(Test stops after 1 minute)

Check Visual check of the motor

Remarks

09/12/2009 203
[ 25-0-001 Error counters ] : Engine\25 Environment: sds 01-29 Function

[ 25-0-001 Error counters ]

Purpose
The purpose of this test is to show the error counter values, except the permanent
errors (PE).

Description
Displayed are:
- the error code
- the error message
- the error counter

The numbers are counted since the last service visit.

Note:
After each service visit the counters must be reset via SDS test 31.

09/12/2009 204