Project Title: Design and analysis of photovoltaic fuzzy logic 3 phase inverter controller
Download All Files Here (18mb): https://we.tl/t-yCi8gAlUnB
I need Simulink Simulation, FIS Structure, Simple Controller and results-discussion writings
report in a word file with screenshots and explanation of results achieved from Simulink. There
code or writings should not be any plagiarised content.
Using Simulink to do design the fuzzy logic three phase inverter controller for PV. I use Matlab
R2023a. Make sure runnable in this version.
Sample Project.pdf: See this sample project paper from senior candidate. Simulation and
chapter 4 almost same like this sample paper but the result in this paper is NOT really good.
Supervisor suggested to use the sample paper but do improvement in this project means that do
the better result.
For an example, if you look at the page 56 in the sample paper, you can see the phase voltage
cannot exceed 240V, but in this paper show the input voltage increase the phase voltage increase
and exceed 240v, so one of the improvements is the phase v MUST NOT exceed 240v.
Again, if you look at the page 53 in the Sample Project.pdf, Vref of Vq is 0，but the maximum
error is 50+，so the improvement is decreasing the error better within 1.
If you check the reference journal paper: Those answers need to meet all the concepts: here:
https://ieeexplore.ieee.org/document/8642881
Project Specification:
1. Frequency of input sine wave, output waveform (50Hz)
2. Frequency of triangular wave PWM (6050 Hz)
3. Calculation value for Inductor and Capacitor
4. Two circuit is needed which are open loop (without fuzzy logic controller) and
close loop
5. Analysis the THD for phase voltage and line voltage in open loop and close
loop, so the waveform of phase voltage and line voltage is needed. * THD<5%
6. Analysis the Error of Vq and Vd by comparing with Vref. Vqref=0 and Vdref=1
(showing waveform) error < 5%
7. Analysis the value for phase voltage and line voltage when using different Dc
input (produce constant voltage Phase voltage = 240Vrms and Line voltage =
415Vrms)
8. Analysis the value for phase voltage and line voltage when using Solar input
(produce constant voltage Phase voltage = 240Vrms and Line voltage =
415Vrms)
9. Total load power = 3000W
Most of the information is already here, but for Fuzzy input and output for Vq and Vd, I am not
very clear, I don't know what is expected outcome for this issue so that I came up with some
reference as per mentioned below:
electronics-08-01335.pdf: this is the reference for expected result，all the waveform and
concept here is correct. This paper have record that V phase should be 240Vrms.
Details-Requirement.pdf: all the detail for Simulink design, analysis and discussion
Note: You will have to do the FIS structure
IMPORTANT TIPS:
Supervisor said me to try closed loop using fuzzy logic with 700v dc input. If ok then use
photovoltaic input. I also have simulation result for simple controller “simple controller.slx”.
For total power is 3000w but load active power is 500W only. Please check these settings.
Expected Result
1. Simple Controller
• Phase voltage, Vpeak = 340 , Vphase = 240rms
• Phase voltage, Vpeak = 415*√2 , Vphase = 240rms
• THD for phase and load current < 5%
• PWM waveform
• Calculation for Capacitor and Inductor value
• Showing Waveform
2. Fuzzy Logic Controller
• Phase voltage, Vpeak = 340 , Vphase = 240rms
• Phase voltage, Vpeak = 415*√2 , Vphase = 240rms
• THD for phase and load current < 5%
• Controller quadrature voltage of Vd and Vq Vrefq=0 Vrefd=1
• Change of error Vd and Vq (less than 1)
• Calculation for Capacitor and Inductor value
• Waveform for Vd and Vq after derivative
• Fuzzy Output d and q parameter
• Make sure the all the results are stable when the input voltage is increased as an
example the phase voltage must = to 240rms
• Calculation for inductor and capacitor value
Deliverables (IMPORTANT):
• Design
• Simple Controller
• Simulation
• FIS Structure
• A Report with screenshots, figures, tables, caption, explanation (12pt times new roman
font, 1.5 line spacing, intext citations and reference list in APA format)
If there is anything you don't understand, you can ask me. If you don't understand, could you
please explain it to me? For controller, explain to me how you do it and how to set the block and
data in Simulink.
Once I award you will accept the project, once accepted please start and give me regular progress
by screenshot, once done completely, then send me files in a zip folder and show final output
based on pdf requirement. Also send me read me file or brief explanation. For controller, explain
to me how you do it and how to set the block and data in Simulink. If there is anything you don't
understand, you must ask me before accepting the project.
If you do my project, when can you start and finish and how much you will charge? I will assign
to a developer who will bid affordable charges and based on quick delivery.
