SAAMI New Cartridge & Chamber
Maximum Average Pressure (MAP)* = 57,500 psi Instrumental Velocity**: 125-gr @ 2,450 fps
Crusher pressure limits not established. 130-gr @ 2,425 fps
* Refer to ANSI/SAAMI Z299.4 for pressure guideline interpretation description. (** - Based on a 16” test barrel.)
ISSUED: 01/20/2020 300 HAM R [300 HAMR] REVISED: 06/06/2023
.030 + .010 CARTRIDGE
(0.76 + 0.25)
UNLESS OTHERWISE NOTED
.027 - .010 BODY DIA. -.008 (0.20)
.3646 D .3512 B
(0.69 - 0.25)
.045 - .010
*
(9.261) (8.920)
(1.43 - 0.25) .3759 (9.548) .3660 (9.296) .332 CYL
(8.43) .309 - .003
35°+20° (7.85 - 0.08)
25°- 6° 30° B
.378 - .010 .332 - .020 BULLET(1)
(9.60 - 0.25) (8.43 - 0.51) .018 + .025 R
(0.46 + 0.64)
.200 B 1.000 (25.40) B .025 R MAX
(5.08) (0.64)
1.3411 (34.064)
*D
1.3527 - .0070 (34.359 - 0.178)
1.3693 (34.781)
*D
1.603 - .015 (40.72 - 0.38)
2.165 (54.99) MIN – . 6 . MAX
.3512 B
(8.920)
BREECH *
(9.323)
.337
.3670 D (8.56) * .300 (7.62)
Bore Dia.
FACE .3768 .3682 .334 .309 CYL .308 (7.82)
(8.48) (7.85) Groove Dia.
(9.571) (9.352)
30° B 30° B 1°30' B
.3785 D
(9.614) .018 R MAX
(0.46)
.200 B 1.000 (25.40) B .025 + .025 R
(0.64 + 0.64)
(5.08)
1.3360 (33.934)
*D
1.3497 (31.742) MIN 1. . MAX
1.3620 (34.595)
*D CHAMBER
UNLESS OTHERWISE NOTED
1.615 (41.01)
ALL DIA +.002 (0.05)
1.6367 (41.571) D LENGTH TOL. +.015 (0.38)
1.678 (42.62)
1.8498 (46.986) D
D 4 GROOVES TWIST: 12.00 (304.8) R.H. OPTIONAL
D .176 + .002 (4.47 + 0.05) WIDE MINIMUM BORE & GROOVE AREA: .0736 inch² (47.483 mm²)
NOTE:
B = BASIC (XX.XX) = MILLIMETERS = HEADSPACE DIMENSION
D = REFERENCE DIMENSION
*
= DIMENSIONS ARE TO INTERSECTION OF LINES
ALL CALCULATIONS APPLY AT MAXIMUM MATERIAL CONDITION (MMC)
1 – BULLET PROFILE IS SHOWN FOR ILLUSTRATIVE PURPOSES ONLY DO NOT SCALE FROM DRAWING
Copyright © Sporting Arms and Ammunition Manufacturers’ Institute, Inc. All rights reserved. No part of this publication may be
reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher
SAAMI New V&P Test Barrel
300 HAM R [300 HAMR]
ISSUED: 01/20/2020 V&P TEST BARREL REVISED: 06/06/2023
.3670 D
(9.323) *
.3682
(9.352)
.3512 B .300 (7.62)
TRANSDUCER LOCATION C L (8.920) Bore Dia.
BREECH
1.161 - .010 (29.49 - 0.25) .337
(8.56) * .308 (7.82)
Groove Dia.
FACE .334 .309 CYL
.3768
(9.571) (8.48) (7.85)
30° B 30° B 1°30' B
.3785 D
(9.614) .018 R MAX
(0.46)
1.000 (25.40) B .025 + .025 R
.200 B
(5.08) (0.64 + 0.64)
1.3360 (33.934)
*D
1.3497 + .0005 (34.282 + 0.013)
1.3620 (34.595)
*D
1.615 (41.01)
1.6367 (41.571) D
1.678 (42.62)
1.8498 (46.986) D
16.000 ± .010 (406.40 ± 0.25)
DO NOT SCALE FROM DRAWING
NUMBER OF GROOVES: 4
WIDTH OF GROOVES: .176 + .002 (4.47 + 0.05)
TWIST RATE: 12.00 (304.8) R.H.
DIAMETER OF PISTON HOLE: Crusher pressures not established.
TRANSDUCER DIAMETER: .250 (6.35)
LAND AND GROOVE DIMENSIONS TO BE UNLESS OTHERWISE NOTED,
WITHIN TOLERANCES THROUGHOUT ALL DIAMETERS +.0005 (0.013)
LENGTH OF BARREL. LENGTH TOLERANCE + .005 (0.13)
NOTE:
B = BASIC D = REFERENCE DIMENSION = HEADSPACE DIMENSION
* DIMENSIONS ARE TO INTERSECTIONS OF LINES (XX.XX) = MILLIMETERS
ALL CALCULATIONS APPLY AT MAXIMUM MATERIAL CONDITION (MMC)
Copyright © Sporting Arms and Ammunition Manufacturers’ Institute, Inc. All rights reserved. No part of this publication may be
reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher
