n Transmitters & Positioners Position of the valve can be determined accurately and precisely using either contact type or non-contact type position transmitters. Contact type position transmitters includes Potentiometer and Electronic Position ‘Transmitters (RWG 1001 / RWG 2002 / RWG 2002 DG) whereas non-contact type position transmitters include Inductive Position Transmitters (IWG 1002 /IWG 1003). Potentiometer ‘Apotentiometer is used as sensor for actuator. Single turn wire wound potentiometer with 4.7 kOhm with Se eae linearity 20.5% is available for this purpose. His available in single or tandem version. ‘Configuration 3 Wire Technical Data - Potentiometer ‘Supply Voltage a Resistance 4.7 kOhm 20.5% Gnnenan 0/4220 mA Power Rating 3 Watt at 40°C Input Resistance 150 kOhms jle of Rotatic (275° + 5° Ang! eo # Displacement of zero 425% — position, Max. Linearity 20.5% Displacement of end position, Max. biaieekidhadad Electronic Position Transmitter RWG1001 ey wacom voltage variation - This device is a signal converter for the transformation of resistance value into proportionate current signal. it | Temp. Drift 0.2% 10°C an alsa be placed in the actuator where the position determined by the potentiometer is converted into4-20 | Linearity not considering mAcurrentsignal. potentiometer 0.05% As position transmitter, preferably a potentiometer of 4.7 kOhm should be used so that the reference voltage a . source is not overloaded. This device requires 24VDC Electronic Position Transmitter RWG 2002 power su ulated within 415%. Auma power supply anne Off recommended fer tis purpose. This is basically same as RWG 1001, however with 2 RWG 1001 Is 2 3 wire system and is having linearity of wire system. The linearity is less than 1%. 0.05%. RWG 2002Position Transmitters & Positioners Technical Data - RWG 2002 Inductive Position Transmitter IWG 1002 Configuration 2Wire When using Auma actuators for regulating duty with —— 2400 Min. 18, | Tanemiter can‘be fed tae prodae ead out of Max. 33 V position, Ouput Current 4-20 mA, The output signal is used as feedback to electronic Input Resistance 150 kOhms Erte pars, © near varabio aiforontal tanctormor Biplcaent ot zero Fostion, | sey, Inagreticcor nf meseurng eal svensk fo proportional signal. The transmitter has no moving - — contacts. This device requires 24 V DC power supply Displacement of End Position, | rom 60 to 100% | regulated within #15%. Auma power supply unit PS 01 Max. is recommended for this purpose. The linearity of the unitis less than 0.3%. Influence of supply voltage eamerie Max. 0.15% Linearity not considering a potentiometer Dual Output Position Transmitler RWG 2002 DG Itis a signal converter device for the transformation of resistance value into proportionate galvanically isolatad two current outputs. This device requires 24 V DC IWG 1002 power supply regulated within 10%. Auma power supply unit PS 01 is recommended forthis purpose. Technical Data - WG 1002 (lated Le we) ; apr Configuration 2Wire ee moan og 24 DC won Lu en ce ace 15% regulated Fbbiome | - — Output Current 4-20 mA Technical Data - RWG 2002 DG eee 600 Ohms 24V DC supply Vol Displacement of zero ply Voltage 10% regulated | | Petter Max 325% Output 1 (Isolated) 0/4-20mA | | Sesiacement of end Output 2 (Isolated) 074-20ma _| | Dlsriocoment 60 to 100% Current Draw “ne Temp. drift 0.4% 110°C Adjustability of : in 50% iene Linearty (not considering | < g, 39, Adjustabllity of Zero 425% LvDT) ° ‘Change in Output due to Input ‘Supply Variation <0.2% Linearity Error for both Outputs | <1%CMU Cee eel] Inductive Position Transmitter IWG 1003. IWG 1003 is similar to IWG 1002 however with 3 wire system. Electronic Positioner CU 01 ‘The electronic positioner CU 01 is designed as a three level positioner for regulating of actuator. By comparing ‘two input signals (reference signal W & regulating signal X), the positioner determines the difference. In case this exceeds a certain value, the actuator is switched on by relays. The direction of rotation {opening or closing) depends upon the plus or minus sign of the deviation. Thus, the regulating signal generated by potentiometer or LVDT changes & when the regulating signal & reference signal become equal, the actuator stops as long as no new correction is required. IWG 1003 Technical Data - IWG 1003 Configuration 3 Wire 24V DC ee ee) £15% regulated Output Current 014-20 mA Resistance Max. 600 Ohms cuot Diglacoment of zero | 27534 Technical Data - CU 01 Input W 0-20 mA (4 - 20 mA) prepracoment fend 60 to 100% eee 0-20 mA(4- 20 mA) : or 0- Uref Temp. drift 0.4% / 10°C Tine delay 120 wwe Linearity (not considering | < o, 994 LvDT) ‘Adjustment of zero point | 0 - 20% ‘Adjustment of end para 60 to 100% Sensitivity (dead band) | 1% - 10% Relay output (max. ret 230, 108 * Positioner with Pulse Width Modulation are available for critical applications.Position Transmitters & Positioners Signal Isolator Auma signal isolator are available in various versions: Power supply conditions: 230VAC, 110 VAC or24 VDC Various input signals: 4-20mA or1-5V ED Signal Isolator Various output signals: 4-20 mA single or dual or 4 - 20 mA& 1-5 V. Isolation is provided between input and output and also between two outputs. Technical Data - Signal Isolator Uo, thus Uc can serve as common reference potential forwhole regulating system. Supply vottage to PS 01 is 220 Vor 110V+15%, 50 Hz The maximum output oltageis Ua: V1 Version | Version Il : For remote position indication with potentiometer 220 Ohms as position transmitter. In this, two additional potentiometers P1 and P2 are fided for positions zero and maximum. A voltmeter of 1 V, calibrated in % is used for visual indication of valve travel. This voltmeter is Power Supply Fr vae i jee connected to the PS 01 (Version II) as shown 24VDCH1V below: Input Signal 4 : zana | 4-20 mA single th oll a [H Output Signal 4-20 mA dual 4 ! 4-20mA&1-5V : | | ‘Accuracy 40.1% of output sapn a | 42% min. at zero ‘Version It Zero & span adjustment | 10% min. at span Technical Data - PS 04 Power Supply Unit PS 01 Supply voltage and | 220 V or 115 V (415%) frequency 50 Hz or60 Hz This unit gives 24 V DG power supply for electronic positioner CU 01 and electronic position transmitter, in Power drawn 9VA case 24V DCis notavallable atsite. There are two versions available: Ouputvotage Jog ya 100 ‘Version|: Forregulating application with CU 01: The output voltage Uo & Uc require no trimming | Amounting Snap on type for DIN rail potentiometer. The voltage Ucis diverted from voltage a