FRP GATES
MM08 FRP GATES
08.02.2016 Rev. 3
COMPOSITE SOLUTION
PAGE 1
SUMMARY
1. USES AND CHARACTERISTICS ....................................................................................................................................3
2. EMPLOYMENT FIELDS ....................................................................................................................................................4
3. MATERIALS........................................................................................................................................................................5
3.1 TABLE OF PROFILES AND STRUCTURAL ACCESSORIES ....................................................................................5
3.2 TABLE OF GRATINGS, STRUCTURAL PROFILES FOR GATE CLADDING ...........................................................6
3.2.1. TABLE OF FRP GRATINGS FOR GATE CLADDING………………………………………………………………. 6
3.2.2. TABLE OF FRP PROFILES FOR GATE CLADDING ………………………………………………………………..6
4. INSTRUCTIONS FOR DESIGN ENGINEER ....................................................................................................................7
4.1 DOUBLE SWING DRIVEWAY GATE.............................................................................................................................7
4.1.1 OVERALL DIMENSIONS ..............................................................................................................................................8
4.2 SINGLE SWING PEDESTRIAN GATE ........................................................................................................................9
4.2.1 OVERALL DIMENSIONS ........................................................................................................................................... 10
5. ASSEMBLING INSTRUCTIONS.................................................................................................................................... 11
5.1 ADJUSTABLE PLATE FIXING FOR DOUBLE SWING GATES ................................................................................ 11
5.2 PIVOT FIXING FOR SINGLE SWING GATES ............................................................................................................ 11
PAGE 2
1. USES AND CHARACTERISTICS
Gates
M.M. gates are made with FRP profiles and gratings, they
assure several advantages compared to normal metal ones:
a. High resistance to chemical and atmospheric
aggressions
b. High mechanical/weight ratio
c. Long-lasting
d. Lightness
e. Dimensional stability
f. High dielectric properties
g. No maintenance
h. Easy to install
Gates are supplied preassembled and complete of all
necessary fixing accessories.
MM gates are CE marked according to the UE 305/2011 regulation.
Tested under the UNI EN 13241-1 norm.
PAGE 3
2. EMPLOYMENT FIELDS
M.M. GATES can be installed in any plant, but they are mainly used in corrosive environments where their
characteristics are emphasized, as:
1. In corrosive environments, mainly in plants where conventional materials are not long lasting or need
continuous varnishing or protection with high maintenance costs and, in any case, do not guarantee safety in
the working environment.
2. In the electric industry, particularly where the safety of the workers is determined by the electric insulation.
3. In airports for the transparent radio frequency property.
Industries and sectors that use M.M. gates are:
• Mineral industries
• Electric stations
• Electric distribution cabins
• Transport field
• Construction industry
• Others.
PAGE 4
3. MATERIALS
3.1. TABLE OF PROFILES AND STRUCTURAL ACCESSORIES
USE
DIMENSIONS BAR WEIGHT
PROFILES DESCRIPTION (D=driveway COLOR
(mm) LENGTH (m) (Kg/m)
P=pedestrian)
rectangular
D/P 80x50x5 6 2.04 grey
structural profile
rectangular
D/P 85x25x3 6 1.17 grey
structural profile
400x400 (C)
FRP corner
D/P grey
reinforcing
200x200 (P)
S.S. AISI 304 upper
and lower pockets
with S.S. adjustable D
hinge and M18
dowel
S.S. AISI 304 lower
D
pockets for drop rod
S.S. AISI 304 upper
pockets with slide D
bolt latch
S.S. AISI 304
intermediate pocket D
with slide bolt latch
Stainless steel hinge
P
for single swing gate
S.S. slide bolt latch
and plate for wall P
fixing
Stainless steel accessories
- M8X100 screws with nut
- M6X25 screws with fender or washer
- 4x12mm rivets
3.2 TABLE OF STRUCTURAL GRATINGS AND PROFILES FOR GATE CLADDING
The gate is built by using FRP gratings, profiles, and laminated plates.
PAGE 5
3.2.1. TABLE OF FRP GRATINGS FOR GATE CLADDING
PANELS
MESH WEIGHT
GRATINGS DESCRIPTION DIMENSIONS 2 COLOR
(mm) (Kg/m )
(mm)
Grey
Grating SCH60/25 100x60 1500x2000 7
Grey
1000 x 2000
Grating SCH30/28 100x30 12
1500 x 2000
1000 x 2000
1000 x 3000
Grating SCH38/25 38x38 11 Grey
1000 x 4038
1225 x 3660
3.2.2. TABLE OF FRP PROFILES FOR GATE CLADDING
DIMENSIONS BAR LENGTH WEIGHT
PROFILES DESCRIPTION COLOR
(mm) (m) (Kg/m)
Tubular profile Ø 26x19 6 0.5 Yellow/grey
Flat profile 40x5 6 0.36 Yellow/grey
PAGE 6
4. INSTRUCTIONS FOR DESIGN ENGINEER
4.1 DOUBLE SWING DRIVEWAY GATE
Legend
1. Rectangular structural profile in reinforced polyester resin with continuous glass fibers section mm 80x50 thickness
mm 5;
2. Cladding (see point 3.2);
3. Corner reinforcing in polyester resin reinforced with continuous glass fibers;
4. Bracing profile in polyester resin reinforced with continuous glass fibers, rectangular section mm 80x25 thickness
mm 3;
5. S.S. triangular pocket block with hinge for gate;
6. Galvanized steel threaded plate for dowel fixing;
7. Ground locking device with drop rod;
8. Upper locking device with steel latch;
9. Intermediate manual locking device with latch.
PAGE 7
4.1.1 OVERALL DIMENSIONS
The type of cladding and the dimensions specified in the drawing determine the dimensions of M.M.’s double swing
gates.
A “SCH60/25” type grating cladding gate has been considered in the following table.
1. Clear span (L)
2. Free space between column and swing (G)
3. Swing net dimension (l)
4. Free space between the two swings (g)
L gate g G l L grating H grating Hmax gate
(mm) (mm) (mm) (mm) (mm) (mm) (mm)
3000 14 126 1367 1261 1800 2000
4000 14 141 1852 1746 1800 2000
5000 14 104 2389 2283 1800 2000
6000 14 126 2867 2761 1800 2000
PAGE 8
4.2 SINGLE SWING PEDESTRIAN GATE
Legend
1. Rectangular structural profile in reinforced polyester resin with continuous glass fibers section 85x25 mm thickness 3
mm;
2. Cladding (see point 3.2);
3. Corner reinforcing in polyester resin reinforced with continuous glass fibers;
4. S.S. gate hinge;
5. Central manual locking devise with latch;
6. Rectangular gate stanchion in polyester resin reinforced with continuous glass fibers section 80x50 mm thickness 5
mm.
PAGE 9
4.2.1 OVERALL DIMENSIONS
The type of cladding and the dimensions specified in the drawing determine the dimensions of M.M.’s single swing
gates.
A “SCH60/25” type grating cladding gate has been considered in the following table.
1. Clear span (L)
2. Free space between column and swing (G)
3. Swing net dimension (l)
4. Free space between column and swing (g)
L gate g G l L grating H grating Hmax gate
(mm) (mm) (mm) (mm) (mm) (mm) (mm)
1516 15 70 1449 1381 1900 1950
1216 15 70 1150 1082 1900 1950
1037 15 70 971 903 1900 1950
PAGE 10
5. ASSEMBLING INSTRUCTIONS
5.1 ADJUSTABLE PLATE FIXING FOR DOUBLE SWING GATES
The adjustable hinges must be fixed to the bearing concrete column with expansion bolts. It is necessary to drill a 20 mm
diameter hole with a varying depth in the concrete for the adjustment of the pivots. After the hole is done it is very simple to
adjust the pivot hinge’s threaded bar to the plate. The dowel must fit into the concrete for at least 30 mm. (Fig. 1)
A – M20 hole plate
B – M18 dowel
C – S.S. triangular pocket with
hingeblock
Fig. 1
5.2 PIVOT FIXING FOR SINGLE SWING GATES
The pivot is fixed to concrete with 4 M8 anchor bolts and to FRP stanchions with M8 screws (Ffig. 2).
Fig. 2
PAGE 11
