Back

UAIS TRANSPONDER

FA-100

PRINTED IN JAPAN

More user manuals on ManualsBase.com

 The paper used in this manual
is elemental chlorine free.

FURUNO Authorized Distributor/Dealer

9-52 Ashihara-cho,
Nishinomiya, 662-8580, JAPAN

Telephone : 0798-65-2111
Fax : 0798-65-4200

All rights reserved. Printed in Japan FIRST EDITION : SEP. 2002

H5 : OCT. 17, 2005
Pub. No. IME-44170-H5

( AKMU ) FA-100 *00080932513*

*00080932513*
*00080932513*

More user manuals on ManualsBase.com

 SAFETY INSTRUCTIONS

WARNING CAUTION
ELECTRICAL SHOCK HAZARD Observe the following compass safe
Do not open the equipment distances to prevent interference to a
unless totally familiar with magnetic compass:
electrical circuits and
service manual.
Standard Steering
compass compass
Only qualified personnel
should work inside the FA-100 1.0 m 0.6 m
equipment.

Turn off the power at the switchboard CB-100 0.6 m 0.4 m

before beginning the installation.
GVA-100 0.3 m 0.3 m
Fire or electrical shock can result if the
power is left on.
DB-1 0.3 m 0.3 m
Do not install the equipment where it
may get wet from rain or water splash. PR-240-CE 0.9m 0.6 m

Water in the equipment can result in fire,

electrical shock or damage the equipment. Attach securely protection
earth to the ship's body.
Be sure that the power supply is
compatible with the voltage rating of The protection earth is required
the equipment. to the power supply to prevent
electrical shock
Connection of an incorrect power supply
can cause fire or damage the equipment.
The voltage rating of the equipment appears
on the label above the power connector.

i
More user manuals on ManualsBase.com
 TABLE OF CONTENTS

SYSTEM CONFIGURATION................................................................................ iii

EQUIPMENT LISTS ............................................................................................. iv

1. MOUNTING ....................................................................................................... 1
1.1 Antenna Unit....................................................................................................................1
1.1.1 GPS antenna unit ...............................................................................................1
1.1.2 VHF antenna ......................................................................................................3
1.1.3 GPS/VHF combined antenna ..............................................................................5
1.2 Transponder Unit .............................................................................................................8
1.3 Junction Box..................................................................................................................10
1.4 Power Supply (option) ...................................................................................................11
1.5 Pilot Plug (option) ..........................................................................................................11

2. WIRING ........................................................................................................... 12

3. INPUT/OUTPUT SIGNAL ............................................................................... 15

3.1 Inputs from Sensors.......................................................................................................15
3.2 Input/Output of AIS Signal .............................................................................................16
3.3 Input of Gyrocompass Signal.........................................................................................17
3.4 Alarm Signal Output.......................................................................................................17
3.5 LAN Input/Output...........................................................................................................18
3.6 Pilot Plug .......................................................................................................................18
3.7 Jumper Setting in the Junction Box................................................................................19
3.8 Input/Output Sentences .................................................................................................20
3.9 Changing Ship’s Mains Specifications............................................................................21

4. SETTING AND ADJUSTMENT ....................................................................... 22

4.1 Setting MMSI, IMO No., Name and Call Sign ................................................................22
4.2 Setting GPS Antenna Position and Ship’s Type .............................................................24
4.3 System Settings.............................................................................................................26

PACKING LIST
OUTLINE DRAWINGS
INTERCONNECTION DIAGRAM

ii
More user manuals on ManualsBase.com
 SYSTEM CONFIGURATION
Either

GPS antenna VHF whip antenna

GPS/VHF
GPA-017S combined antenna
GSC-001 GVA-100

Distributor unit
DB-1

Transponder unit
FA-100

Junction box CB-100

Power supply
PR-240-CE AD-100 GPS Navigator *

Other external equipments

Gyrocompass

: Standard

Ship’s mains : Option

100-115/200-230 VAC 24 VDC : Local supply
1f, 50/60Hz 12-24 VDC

*: External GPS Navigation is required.

Category of the units

GPA-017S Exposed to the weather
GSC-001 Exposed to the weather
GVA-100 Exposed to the weather
FA-100 Protected from the weather
CB-100 Protected from the weather
DB-1 Protected from the weather
PR-240-CE Protected from the weather

iii
More user manuals on ManualsBase.com
 EQUIPMENT LISTS
Standard supply
No. Name Type Code no. Qty Remarks
1 Transponder Unit FA-100 - 1
2 Junction Box CB-100 - 1
3 GPS Antenna GPA-017S -
GPS Antenna GSC-001 -
GPS/VHF Combined GVA-100* - 1 Select one.
Antenna
4 Installation Materials CP24-00101* 005-950-730 1 For DB-1
CP24-00102* 005-950-700 1 For FA-100
CP05-08701* 005-949-280 1 For CB-100
CP24-00121** 005-952-350 1 For GPA-017S
CP24-00141* 005-952-330 1 For GVA-100
**: for Japan only
Optional supply
No. Name Type Code no. Remarks
1 Antenna cable set CP20-01700(30m) 004-372-110 For GPS or Combined antenna
8D-FB-CV *30M*, CP20-01701
2 Antenna cable set CP20-01710(50m) 004-372-120 For GPS or Combined antenna
8D-FB-CV *50M*, CP20-01701
3 Flush mount kit A OP24-1 005-950-740
4 Flush mount kit B OP24-2 005-950-750
5 Mast mount fixture CP20-01111 004-365-780 For GPA-017S
6 Right-angle No.13-QA330 000-803-239 For GPA-017S
antenna base
7 L-angle antenna No.13-QA310 000-803-240 For GPA-017S
base
8 Antenna base for No.13-RC5160 000-806-114 For GPA-017S
rail mount
9 VHF whip antenna FAB-151D 000-572-029 For Japan only
10 Antenna fixing 4-310071 000-572-184 For FAB-151D
bracket
11 VHF whip antenna 150M-W2VN 000-113-498 For outside Japan
12 Power supply PR-240-CE - Include installation materials
CP24-00151*
13 Pilot plug OP24-3 000-053-911
14 AD-100 AD-100 - For gyrocompass
15 PC AIS OP24-24-1 005-954-420 CD-ROM, USB protect key
software kit
16 φ80 Mast mount kit OP24-5 005-954-510 For Combined antenna
*: Refer to packing list at the back of this manual.

iv
More user manuals on ManualsBase.com
 1. MOUNTING
1.1 Antenna Unit
1.1.1 GPS antenna unit
Install the GPS antenna unit referring to the drawing at the back of this manual D-1.
When selecting a mounting location for the antenna, keep in mind the following
points.

• Select a location out of the radar beam. The radar beam will obstruct or prevent
reception of the GPS satellite signal.
• There should be no interfering object within the line-of-sight to the satellites. Objects
within line-of-sight to a satellite, for example, a mast, may block reception or prolong
acquisition time.
• Mount the antenna unit as high as possible to keep it free of interfering objects and
water spray, which can interrupt reception of GPS satellite signal if the water freezes.

Extending antenna cable

Three types of antenna cable extensions are optionally available.
a) Antenna cable set CP20-01700

Antenna Unit

Conversion : Connector
0.6 m Cable Assy.
NJ-TP-3DXV-1
Antenna Cable
FA-100
1m 30 m 1m
Fabricate locally. (See next page.)

◆ Waterproofing connector
Wrap connector with vulcanizing tape and then vinyl tape. Bind the tape end with
a cable-tie.

Waterproofing connector

b) Antenna cable set CP20-01710 (8D-FB-CV, 50m)

Connect the cable the same as a) above.
c) Cable type RG-10U/Y (shipyard supply)
Note: The length of this cable should be less than 20 m to prevent signal loss.
The coax. coupling cable assy.(type: NJ-TP+3DXV-1, code no.
000-123-809), coaxial connector(N-P-8DFB; supplied), vulcanizing tape
and vinyl tape are required. Fabricate both ends of the cable as shown in
the figure on the next page.

1
More user manuals on ManualsBase.com
 How to attach the connector N-P-8DFB for cable 8D-FB-CV
Outer Sheath Dimensions in millimeters.
Armor Inner Sheath Shield
Remove outer sheath and armor by the dimensions
shown left.
50 30 Expose inner sheath and shield by the dimensions
shown left.

Cover with heat-shrink tubing and heat.

Cut off insulator and core by 10mm.

30 10

Twist shield end.

Ship on clamp nut, gasket and clamp as shown left.

Clamp Gasket Clamp

Nut (reddish
brown)
Aluminum Foil

Fold back shield over clamp and trim.

Trim shield here.

Cut aluminum foil at four places, 90° from one

another.
Insulator

Fold back aluminum foil onto shield and trim.

Trim aluminum
tape foil here.

1
Expose the insulator by 1mm.
5
Expose the core by 5mm.

Pin Slip the pin onto the conductor. Solder them together
Clamp Nut
Shell through the hole on the pin.

Insert the pin into the shell. Screw the clamp nut into
the shell.
(Tighten by turning the clamp nut. Do not tighten by
Solder through turning the shell.)
the hole.

How to attach connector N-P-8DFB

More user manuals on ManualsBase.com

 1.1.2 VHF antenna
Location
Location of the mandatory AIS VHF-antenna should be carefully considered. Digital
communication is more sensitive than analog/voice communication to interference
created by reflections in obstructions like masts and booms. It may be necessary to
relocate the VHF radiotelephone antenna to minimize interference effects.

To minimise interference effects, the following guidelines apply:

• The AIS VHF antenna should be placed in an elevated position that is as free as
possible with a minimum of 0.5 meters in the horizontal direction from constructions
made of conductive materials. The antenna should not be installed close to any large
vertical obstruction. The objective for the AIS VHF antenna is to see the horizon
freely through 360 degrees.
• The AIS VHF antenna should be installed safely away from interfering high-power
energy sources like radar and other transmitting radio antennas, preferably at least 3
meters away from and out of the transmitting beam.
• There should not be more than one antenna on the same plane. The AIS VHF
antenna should be mounted directly above or below the ship’s primary VHF
radiotelephone antenna, with no horizontal separation and with a minimum of 2.8
meters vertical separation. If it is located on the same plane as other antennas, the
distance apart should be at least 10 meters.

Cabling
• The cable should be kept as short as possible to minimize signal attenuation.
Coaxial cables equal to or better than RG10U/Y are recommended.

• All outdoor installed connectors on coaxial cables should be fitted with preventive
isolation such as vulcanizing tape to protect against water penetration into the
antenna cable.

• Coaxial cables should be installed in separate signal cable channels/tubes and at

least 10 cm away from power supply cables. Crossing of cables should be done at
right angles (90°). The minimum bend radius of the coaxial cable should be 5 times
the cable's outer diameter.

• Install the VHF whip antenna referring to the outline drawing at the back of this
manual. Separate this antenna from other VHF radiotelephone antennas as shown
on the next page to prevent interference to the FA-100.

More user manuals on ManualsBase.com

 Horizontal separation distance
Other VHF whip antenna
Whip antenna for AIS
(GPS/VHF combined
antenna)

More than 10 m

Vertical separation distance

More than
2.8 m

More than 0.5 m

• When coaxial cable RG-10U/Y (shipyard supply) is used, attach the coaxial plug
M-P-7 (dockyard supply) as shown on the next page.

More user manuals on ManualsBase.com

 How to attach the plug M-P-7
Lay the coaxial cable and attach an M-type plug (if necessary) to the cable as
follows.
30 mm
Sheath
1. Remove the sheath by 30 mm. 5 mm 2 mm

2. Bare 23 mm of the center conductor. Trim

braided shield by 5 mm and tin.
3. Slide coupling ring onto cable. Conductor
4. Screw the plug assembly on the cable. Braided shield Insulator
5. Solder plug assembly to braided shield
through solder holes. Solder contact sleeve
Plug assembly Contact sleeve
to conductor.
6. Screw coupling ring into plug assembly.

Solder both Cut conductor here.

Coupling ring sides of hole.
1.1.3 GPS/VHF combined antenna
Install the combined antenna unit referring to the outline drawing. When selecting a
mounting location for the antenna, keep in mind the following points.

• Select a location out of the radar beam. The radar beam will obstruct or prevent
reception of the GPS satellite signal.
• There should be no interfering object within the line-of-sight to the satellites. Objects
within line-of-sight to a satellite, for example, a mast, may block reception or prolong
acquisition time.
• Mount the antenna unit as high as possible. Mounting it this way keeps it free of
interfering objects and water spray, which can interrupt reception of GPS satellite
signal if the water freezes.
• Also, refer to the antenna installation guidelines page 3.

Outdoor Indoor

Distributor DB-1

GPS
Transponder unit
VHF

N-P-8DFB N-P-8DFB
RG-10U/Y

Installation overview of GPS/VHF combined antenna

Note: Optional φ80 mast mount kit (Type: OP24-5, Code no.: 005-954-510) is
required to fix the GPS/VHF combined antenna to the mast (φ60 - 80).

More user manuals on ManualsBase.com

 Mounting procedures
1. Dismount the bottom cover, cut the cable-tie inside the unit and take out the
coaxial connector attached to the combined box.
2. Loosen four screws to loosen whip antenna fixture and pull out the coaxial
connector coming from the combined box through the hole in the whip antenna
fixture.
3. Connect the coaxial connector to the whip antenna base and wrap the junction
part of the whip antenna with vulcanizing tape and then vinyl tape for
waterproofing.
4. Insert the whip antenna from the top of the combined antenna.
5. Secure the whip antenna with whip antenna fixture.
6. Using a new plastic band (supplied), secure the cables and coaxial connector
inside the antenna case.
7. Mount the bottom cover.
8. Fix the GPS/VHF combined antenna to the ship’s stanchion (40 to 50 mm
diameter) with antenna fixing brackets, flat washers and hex. nuts.

Note: Coat the exposed parts of bolts and nuts with silicon sealant.

Whip antenna fixture

Loosen four screws.

(M5x16)

Antenna fixing bracket

Combined box

Bottom cover

GPS/VHF Combined antenna

More user manuals on ManualsBase.com

 The top of the stanchion come
into contact with the flange.

Stanchion

Installing distributor unit DB-1

The length of the cable between the distributor unit and transponder unit is 1 m so
locate the distributor unit within 1 m from the transponder unit. Fix the distributor
unit on the bulkhead, facing the cable entrance downward. Remove the lid of the
distributor unit and secure the unit with two tapping screws.

Tapping screw
(4x30)

Note: Be sure no foreign material or water enters the distributor unit.

More user manuals on ManualsBase.com

 1.2 Transponder Unit
The transponder unit can be installed on a desktop or flush mounted in a panel.
Install it on the chart table or near the steering place, referring to the outline
drawing.

When selecting a mounting location for the transponder, keep the following in mind:
• Keep the transponder out of direct sunlight.
• The temperature and humidity should be moderate and stable.
(Operating temperature range: -15°C to +55°C)
• Locate the unit away from exhaust pipes and vents.
• The mounting location should be well ventilated.
• Mount the unit where shock and vibration are minimal.
• Keep the unit away from electromagnetic field generating equipment such as
motor, generator.
• For maintenance and checking purposes, leave sufficient space at the sides and
rear of the unit and leave slack in cables. Refer to the outline drawing.
• A magnetic compass will be affected if the unit is placed too close to it. Observe
the following compass safe distances to prevent disturbance to the magnetic
compass:
Standard compass: 1.0 meters
Steering compass: 0.6 meters

Desktop mounting
1. Remove two hex. bolts from the lower part of the transponder unit and dismount
the mounting base.

Remove two hex. bolts.

2. Fix the mounting base to the desktop with four tapping screws (6x20: supplied)
or hex. bolts. 120 mm
120 mm

φ8

Front

Service clearance
more than 130 mm
Mounting base
3. Place the transponder unit on the mounting base and secure it with two hex.
bolts.

More user manuals on ManualsBase.com

 Flush mounting
Optional flush mount kit A or B is required for flush mounting. For mounting
dimensions, refer to the outline drawing at the back of this manual.

Flush mount kit A: Type OP24-1 Code no. 005-950-740

Name Type Code no. Qty
1 Cosmetic panel 24-003-2811 100-299-540 1
2 +Tapping screw 5x25 000-802-082 4

1. Cut out a hole in the mounting location, referring to the outline drawing.
2. Remove two hex bolts to dismount the mounting base.
3. Remove six hex bolts from the bottom of the transponder unit to dismount the
mounting pedestal.
4. Set the transponder unit to the cosmetic panel and fix them with six hex bolts.
5. Set the assembly (transponder unit and cosmetic panel) to the hole and fix it
with four tapping screws (5x25).

Flush mount kit B: Type OP24-2 Code no. 005-950-750

Name Type Code no. Qty
1 Mounting bracket 24-003-2821 100-299-550 1
2 Hex bolt M5x25 000-862-125 6
3 Hex nut M5 000-863-108 6
4 Flat washer M5 000-864-128 6
5 Spring washer M5 000-864-258 6

1. Cut out a hole in the mounting location, referring to the outline drawing.
2. Dismount the mounting base and mounting pedestal from the transponder unit.
3. Set the transponder unit to the hole. Using six hex bolts, attach the mounting
bracket at the bottom of the transponder unit from the rear of the flush mounting
panel.
4. Fix with six sets of hex bolt, nut, flat washers and spring washers from the rear
of the flush mounting panel.

More user manuals on ManualsBase.com

 1.3 Junction Box
Mount the junction box where the junction box is protected from rain and water
splash.

Mounting
1. Open the lid of the junction box and fix the junction box with four tapping screws
(5x20). Avoid bundling the 3.3 m cable of the junction box together with any
power cable. This causes malfunction.
2. Connect cables to the terminal board, referring to Chapter 2 and 3.
3. Fix the lid after connecting external equipment.
4. Clamp the cable with several U-type cable clamps (local supply) at suitable
intervals.

Clamp the cable with

U-type cable clamps.
Fixing holes Cable entry
(5x20 tapping screws)

Cable clamp

10

More user manuals on ManualsBase.com

 1.4 Power Supply (option)
The length of the power cable between the power supply and the transponder unit
is 3.5 m. Keep this length in mind when selecting a mounting location. A longer
cable should not be used – voltage drop will result, affecting performance.

When selecting a mounting location for the unit, keep the following in mind:

• Keep the unit out away from areas subject to water splash.
• Locate the unit away from exhaust pipes and vents.
• The mounting location should be well ventilated.
• Mount the unit where shock and vibration are minimal.
• A magnetic compass will be affected if the unit is placed too close to it. Observe
the following compass safe distances to prevent disturbance to the magnetic
compass:
Steering compass: 0.6 m
Standard compass: 0.9 m

Fix the unit with four tapping screws (4x16) to a desktop or the deck as shown in
the figure below. It is not necessary to open the cover.

1.5 Pilot Plug (option)

The pilot plug should be mounted near where the pilot steers the ship. This plug is
used to connect a PC to display AIS information for use by the pilot. Refer to the
outline drawing at the back of this manual for mounting dimensions.

11

More user manuals on ManualsBase.com

 2. WIRING
Connect the equipment, referring to the interconnection diagram at the back this
manual.

GPS Antenna
GPA-017S GPS/VHF Conbined
GSC-001 Antenna GVA-100
150M-W2VN
Either one

0.6 m
Distributor unit
DB-1 0.9 m
***
***
***
RG-10/UY
Attached to Distributor
RG-10/UY (approx. 1m)

: ground is not required.

8D-FB-CV, 30 m/50 m: Option LAN cable
RG-10/UY: Local supply GPS ANT VHF ANT (category 4 or higher)
PC
AUX-1 AUX-2

LAN AD-10 IN TTYCS-1Q**

AD-100 Gyrocompass
EXTRA I/O
MJ-A3SPF0013-035 (3.5 m) *

Transponder AIS sentence out

Power Supply unit (4800 bps)
PR-240-CE FA-100
AC DC DC
IN IN OUT Pilot Plug
Alarm out
GPS receiver
Heading sensor
1.5 sq Speed sensor or ROT
DPYC-1.5** Approx. 3.3 m
Beacon receiver
AIS data In/Out
Ship’s mains
100-115/200-230 VAC TTYCS-1Q** or TTYCS-4**
24 VDC Junction Box
1φ, 50/60 Hz
12-24 VDC CB-100
(Connect to the alternative : Standard
power source.)
: Option
: Local Supply

*: If the ship’s mains is 12 VDC, cable length should be less than 50 cm.

EXTRA IO port: Outputs AIS sentence (4800 bps).

AUX-1, AUX-2 port: Not used.

12

More user manuals on ManualsBase.com

 **: DPYC-1.5, TTYCS-1Q and TTYCS-4 are Japan Industry Standard cable.
Use them or the equivalents.

DPYC-1.5 TTYCS-1Q (Four core twisted)

Armor

Sheath Armor

Sheath
φ = 11.7 mm Shield
Conductor φ = 11.3 mm
S = 1.5 mm 2 Conductor
S = 0.75 mm2
φ = 1.56 mm φ = 1.11 mm

TTYCS-4 (Four twisted pairs)

φ = 18.5 mm Sheath
Armor

Sheath
Shield
Conductor
S = 0.75 mm 2
φ = 1.11 mm

***: Waterproofing connectors

Wrap connector with vulcanizing tape and then vinyl tape. Bind
the tape end with a cable-tie.

Waterproofing connector

13

More user manuals on ManualsBase.com

 Cable Connection at Junction Box
Cable fabrication

Armor Sheath Shield

5 to 6 mm

30

Clamp here by cable clamp.

Connection

1
2

3 Core 5-6 mm

Procedure
1. Insert driver from direction 1 .
2. Tilt slightly toward 2 .
3. Insert cable core to 3 .

14

More user manuals on ManualsBase.com

 3. INPUT/OUTPUT SIGNAL
3.1 Inputs from Sensors
There are three input ports (SENSOR 1, 2 and 3) which are based on the IEC
61162-1/2. The protocol is RS422. If there is no HDT signal from a gyrocompass,
connect the gyrocompass signal (Synchro or step signal) to the “AD-10 IN” port
(D-sub 9 pins) of the transponder unit via the FURUNO A/D Converter AD-100 (See
page 16).

TB1 in the junction box

1 TD3-A
2 TD3-B
SENSOR 3 (EXT GPS IN)
3 GND ISO TTYCS-1Q
(4 cores twisted)
4 RD3-A
GPS navigator only
5 RD3-B
6 GND ISO Isolated GND
7 TD2-A
8 TD2-B SENSOR 2
9 GND ISO
TTYCS-1Q
10 RD2-A
Heading Signal (HDT)
11 RD2-B
12 GND ISO Isolated GND
13 TD1-A
14 TD1-B SENSOR 1
15 GND ISO TTYCS-1Q
16 RD1-A
Speed Signal (SOG)
17 RD1-B
18 GND ISO Isolated GND
19 TD5-A TTYCS-1Q
20 TD5-B
21 GND
DGPS
22 RD5-A Beacon
23 RD5-B Receiver

24 GND GND 0V

15

More user manuals on ManualsBase.com

 3.2 Input/Output of AIS Signal
Three input/output ports are provided for RS-422 protocol, based on the IEC
61162-1/2. Data transmission rate is selectable from 4800 bps and 38.4 kbps.
Normally, Radar/ECDIS/PC, etc. are connected to these ports to exchange data
with the AIS. PC standard protocol RS-232C is also provided in the D-sub port of
the transponder unit.

TB1 in the junctionbox

TTYCS-4
25 TD4-A RD-A
26 TD4-B RD-B
27 GND ISO Isolated GND L/R (INMARSAT) or
28 RD4-A TD-A ECDIS/RADAR
29 RD4-B TD-B

30 GND ISO Isolated GND

31 TD6-A TTYCS-4
RD-A
32 TD6-B RD-B
33 GND ISO Isolated GND EXTRA I/O
34 RD6-A TD-A
35 RD6-B TD-B
36 GND ISO Isolated GND

37 TD8-A TTYCS-4
RD-A
38 TD8-B RD-B
39 GND ISO Isolated GND PC I/O
40 RD8-A TD-A
41 RD8-B TD-B
42 GND ISO Isolated GND
43 TD (232C) Rx port
44 RD (232C) Tx port
21 GND GND
TTYCS-1Q

Note: For TD (232C) and RD (232C), use one twisted pair for TD and one twisted
pair for RD, separately. Use pin #21 for SG.

16

More user manuals on ManualsBase.com

 3.3 Input of Gyrocompass Signal
If the gyrocompass has no HDT signal, the AD-10 format (FURUNO format) signal
can be input via the FURUNO A/D Converter AD-100. Connect the AD-100 to the
“AD-10 IN” port (D-sub 9 pin) on the rear panel of the transponder unit.
FA-100
AD-10 IN
DATA-H >1>
DATA-L >2> Twisted pair cable (Example: TTYCS-1Q cable)
CLOCK-H >3> to DATA terminal of AD-100
CLOCK-L >4>
GND >8>
F.GND >9>

Note: Set data output interval for 200 ms (instead of 25 ms) by internal jumper
inside the AD-100.

3.4 Alarm Signal Output

The FA-100 generates an alarm signal (relay contact signal) for hardware failure
such as transmitter block or sensor abnormality. For details of alarm type, see the
operator’s manual.

Two kinds of contact signals, on (normal closure) or off (normal open), are output,
and are selected at the junction box CB-100 according to the alarm generator
connected. The maximum current and voltage of the contact are 1 A, 125 VAC and
60 VDC. Normally connect to the NC (normal close) between #45 and #47.

TB-1 in the junction box

45 AOL #45-#47: Normal Close

#46-#47: Normal Open
46 AOH
47: common line
47 AOC

17

More user manuals on ManualsBase.com

 3.5 LAN Input/Output
The FA-100 supports Ethernet based on LAN. Its protocol is 10BASE-T and the
transmission rate is 10 Mbps. To connect the FA-100 with other equipment (such as
a PC), use a LAN cable category 4 or higher with shield (SDT). Connect it to the
PC with an RJ-45 connector, and connect to the FA-100 with a D-sub 9 pin
connector, to avoid noise leakage. To use a commercial LAN cable, remove one
connector and solder a D-sub 9 pin connector, supplied in the installation materials.

RJ-45 (Category 4 and higher, SDT)

FA-100 Twisted pair cable
LAN (10B-T)
TD+ >1> 3 RD+
TD- >2> 6 RD-
RD+ >3> 1 TD+
RD- >4> 2 TD-
GND >8>
F.GND >9>

3.6 Pilot Plug

Use the twisted cable TTYCS-4 between the junction box and the pilot plug. The
cable between the PC and the pilot plug should be prepared by the ship’s pilot.

Pilot plug
Junction box J1
TTYCS-4
Terminal board >1>
TB1
>2>
37 TD8-A TD A
>3>
38 TD8-B TD B
>4>
39 GND ISO
RD-A >5>
40 RD8-A PC
RD-B >6>
41 RD8-B
>7>
42 GND ISO SHIELD
>8>
>9>

3mm Crimp-on lug 206486-1

(AMP)

18

More user manuals on ManualsBase.com

 3.7 Jumper Setting in the Junction Box
Each RS-422 RX line (on the PCB 24P0031 in the junction box) has a jumper block
with 240 ohms termination resistor. The junction box is shipped with all jumper
blocks connected between the #3 and #4 terminals pins, terminating RX lines with
240 ohms. Assuming that an external equipment has the output voltage of ±5 V,
more than 21 mA of output current is required.
If multiple equipment are connected to an output port of an external equipment,
change to jumper block setting to between the #1 and #2 pins to reduce the load on
the FA-100. Then, the input impedance of the RS-422 RX lines in the FA-100
becomes more than 2.4 k ohms.
We recommend that you leave the connection of the jumper block between #3 and
#4 pins if only the FA-100 is connected to an external equipment.

Jumper block (6 pcs)

2 Factory setting: #3-#4

1 4
3

19

More user manuals on ManualsBase.com

 3.8 Input/Output Sentences
1) SENSOR 1, SENSOR2, and SENSOR3 ports

These ports can receive IEC61162-1/2 standard data. The transmission rate of
sensor 1, 2, and 3 is selectable from 4800 bps and 38.4 kbps through the menu.

Input sentences are as follows:

$xxDTM, $xxGBS, $xxGGA, $xxGLL, $xxGNS, $xxHDT
$xxOSD, $xxRMC, $xxROT, $xxVBW, $xxVTG

Note: The talker of the underlined sentences has priority as

follows:
GN>GP>GL>LC>IN
Other sentences disregard talker.

2) PC I/O, LR or ECDIS/RADAR, EXTRA I/O and EXTRA 1 I/O ports

These ports can receive or output IEC61162-1/2 standard data. The transmission
rate of signals is selectable from 4800 bps and 38.4 kbps through the menu. The
transmission rate of the EXTRA IO port signal is fixed to 4800 bps.

Input sentences are as follows:

$xxABM, $xxACA, $xxACK, $xxAIR
$xxBBM, $xxDTM, $xxGBS, $xxGGA
$xxGLL, $xxGNS, $xxHDT, $xxLRF
$xxLRI, $xxOSD, $xxRMC, $xxROT
$xxSSD, $xxVBW, $xxVSD, $xxVTG

Note: The talker of the underlined sentences has priority as

follows:
GN>GP>GL>LC>IN
Other sentences disregard talker.
Output sentences are as follows:
$AIABK, $AIACA, $AIALR, $AILRF,
$AILR1, $AILR2, $AILR3, $AITXT,
$AIVDM, $AIVDO

20

More user manuals on ManualsBase.com

 3.9 Changing Ship’s Mains Specifications
The power supply PR-240-CE is shipped ready for connection to a 200-230 VAC
ship’s mains. If the ship’s mains is 100 VAC – 115 VAC, change the tap connection
and terminal board connection as below. Attach label supplied as accessories to
the punch mark in the front panel according to the ship’s mains.

Ship’s mains Tap connection Terminal board

connection #1 & #2
100-115 VAC SEL 115 V b
200-230 VAC SEL 230 V a

200-230 VAC 100-115 VAC

1 White 1 White

2 Black 2 Black
3 3

Punch mark

(a) (b) Front

SEL
1 115 V
2
3 Heat sink
SEL
4 230 V
5
6
7
8

Tap connection (Pull out to remove)

Terminal board connection

Top view (Cover removed)

21

More user manuals on ManualsBase.com

 4. SETTING AND ADJUSTMENT
After installing the equipment, set up the own ship’s static information (MMSI, IMO
number, ship’s name, call sign, type of ship and GPS antenna position). Also, set
up the system settings.

4.1 Setting MMSI, IMO No., Name and Call Sign

1. While holding down the [0] key, press the [POWER] key.
2. After the following message appears, release the [0] key. (It takes several
seconds before the message appears.)

NOW STARTING
CHECKING MEMORY

3. After the following window appears, enter the password. Note that the password
is known by only the FURUNO dealer.

[ENTER PASSWORD]

PASSWORD:

4. Press the [ENT] key to display the SET MMSI & IMO# window.

[SET MMSI & IMO#]

Asterisk marks MMSI :
current selection. IMO# :
NAME :

C.SIGN :

SET: [ENT]

5. Enter ship’s MMSI (Maritime Mobile Service Identity) in nine digits.

6. Press the [NEXT] key to select IMO#.
7. Enter ship’s IMO number in nine digits. If the IMO number has 7 digits, enter “0”
twice followed by IMO#. IF the ship has no IMO number, enter all zeroes.
8. Press the [NEXT] key to select NAME.

22

More user manuals on ManualsBase.com

 9. Enter ship’s name, using up to 20 alphanumeric characters. To switch between
alphabet and numerical character, press the [SFT] key. To enter an alphabet,
press corresponding key several times until desired letter is displayed. For
example, if you press the [2] key continuously, the character A, B and C appear
cyclically. If you want to enter the same letter or an other letter with the same
key (for example, AA or AC), press the [6] key while pressing the [SFT] key, to
send the cursor to the next position.
10. Press the [NEXT] key to select C.SIGN.
11. Enter call sign, using up to seven alphanumeric characters.
12. Press the [ENT] key to register data. The INIT SETTINGS sub-menu appears.

23

More user manuals on ManualsBase.com

 4.2 Setting GPS Antenna Position and
Ship’s Type
1. In the INIT SETTING sub-menu, press the [6] key to open the SET ANTENNA
POS window.

SET ANTENNA POS

1 INTERNAL ANT POS
2 EXTERNAL ANT POS

SET ANTENNA POS window

2. With 1 selected, press the [ENT] key. The 1 is for entering internal GPS antenna
position and 2 is for external GPS which is connected to the AIS.

[INTERNAL ANT POS]

A
A: 000 m
B: 000 m
B C: 00 m
C D D: 00 m

INTERNAL ANT POS window

3. Enter locations of GPS antenna, by using the numeric keys and the [NEXT] key,
and finally press the [ENT] key.
A: Distance from bow to GPS antenna position
B: Distance from stern to GPS antenna position
C: Distance from port to GPS antenna position
D: Distance from starboard to GPS antenna position
4. Enter external GPS antenna position similar to how you entered internal GPS
antenna position.
5. Press the [MENU] key to return to the INIT SETTINGS sub-menu.
6. Press the [4] key to display the SET TYPE&CREW window.

[SET TYPE&CREW]
CREW : 0012
TYPE CLASS : A TYPE CLASS cannot
TYPE NO. : 0 be changed.
TYPE NAME (A = IMO type)

SET TYPE&CREW window

24

More user manuals on ManualsBase.com

 7. Press the [NEXT] key to select TYPE NO.
Confirm type of ship with ship’s captain before setting it.
8. Press the [2], [4], [6] or [8] key as appropriate to select your ship’s type,
referring to the list on below.
10 FUTURE USE ALL SHIPS OF THIS TYPE 60 PASSENGER SHIPS ALL SHIPS OF THIS TYPE
11 FUTURE USE CARRYING DG, HS, OR MP(A) 61 PASSENGER SHIPS CARRYING DG, HS, OR MP(A)
12 FUTURE USE CARRYING DG, HS, OR MP(B) 62 PASSENGER SHIPS CARRYING DG, HS, OR MP(B)
13 FUTURE USE CARRYING DG, HS, OR MP(C) 63 PASSENGER SHIPS CARRYING DG, HS, OR MP(C)
14 FUTURE USE CARRYING DG, HS, OR MP(D) 64 PASSENGER SHIPS CARRYING DG, HS, OR MP(D)
15 FUTURE USE FUTURE USE 65 PASSENGER SHIPS FUTURE USE
16 FUTURE USE FUTURE USE 66 PASSENGER SHIPS FUTURE USE
17 FUTURE USE FUTURE USE 67 PASSENGER SHIPS FUTURE USE
18 FUTURE USE FUTURE USE 68 PASSENGER SHIPS FUTURE USE
19 FUTURE USE NONE 69 PASSENGER SHIPS NONE
20 WIG ALL SHIPS OF THIS TYPE 70 CARGO SHIPS ALL SHIPS OF THIS TYPE
21 WIG CARRYING DG, HS, OR MP(A) 71 CARGO SHIPS CARRYING DG, HS, OR MP(A)
22 WIG CARRYING DG, HS, OR MP(B) 72 CARGO SHIPS CARRYING DG, HS, OR MP(B)
23 WIG CARRYING DG, HS, OR MP(C) 73 CARGO SHIPS CARRYING DG, HS, OR MP(C)
24 WIG CARRYING DG, HS, OR MP(D) 74 CARGO SHIPS CARRYING DG, HS, OR MP(D)
25 WIG FUTURE USE 75 CARGO SHIPS FUTURE USE
26 WIG FUTURE USE 76 CARGO SHIPS FUTURE USE
27 WIG FUTURE USE 77 CARGO SHIPS FUTURE USE
28 WIG FUTURE USE 78 CARGO SHIPS FUTURE USE
29 WIG NONE 79 CARGO SHIPS NONE
30 FISHING 80 TANKER ALL SHIPS OF THIS TYPE
31 TOWING 81 TANKER CARRYING DG, HS, OR MP(A)
32 LENGTH OF THE TOW EXCEEDS 200M OR BREADTH EXCEEDS 25M 82 TANKER CARRYING DG, HS, OR MP(B)
33 ENGAGED IN DREDGING OR UNDERWATER OPERATIONS 83 TANKER CARRYING DG, HS, OR MP(C)
34 ENGAGED IN DIVING OPEARATIONS 84 TANKER CARRYING DG, HS, OR MP(D)
35 ENGAGED IN MILITARY OPEARATIONS 85 TANKER FUTURE USE
36 SAILING 86 TANKER FUTURE USE
37 PLEASURE CRAFT 87 TANKER FUTURE USE
38 FUTURE USE 88 TANKER FUTURE USE
39 FUTURE USE 89 TANKER NONE
40 HSC ALL SHIPS OF THIS TYPE 90 OTHER TYPE OF SHI ALL SHIPS OF THIS TYPE
41 HSC CARRYING DG, HS, OR MP(A) 91 OTHER TYPE OF SHI CARRYING DG, HS, OR MP(A)
42 HSC CARRYING DG, HS, OR MP(B) 92 OTHER TYPE OF SHI CARRYING DG, HS, OR MP(B)
43 HSC CARRYING DG, HS, OR MP(C) 93 OTHER TYPE OF SHI CARRYING DG, HS, OR MP(C)
44 HSC CARRYING DG, HS, OR MP(D) 94 OTHER TYPE OF SHI CARRYING DG, HS, OR MP(D)
45 HSC FUTURE USE 95 OTHER TYPE OF SHI FUTURE USE
46 HSC FUTURE USE 96 OTHER TYPE OF SHI FUTURE USE
47 HSC FUTURE USE 97 OTHER TYPE OF SHI FUTURE USE
48 HSC FUTURE USE 98 OTHER TYPE OF SHI FUTURE USE
49 HSC NONE 99 OTHER TYPE OF SHI NONE
50 PILOT
51 SEACH AND RESCURE VESSELS WIG: Wing in ground
52 TUGS HSC: High speed craft
53 PORT TENDERS DG: Dangerous goods
54 VESSELS WITH ANTI-POLUUTION FACILITIES OR EQUIPMENT HS: Harmful substances
55 LAW ENFOREMENT VESSELS MP: Marine pollutants
56 SPARE-FOR ASSIGNMENTS TO LOCAL VESSELS 0-9: Undefined
57 SPARE-FOR ASSIGNMENTS TO LOCAL VESSELS
58 MEDICAL TRANSPORTS
59 SHIPS ACCORDING TO RESOLUTION NO 18

9. Press the [ENT] key to return to the INIT SETTING sub-menu.

25

More user manuals on ManualsBase.com

 10. Press the [MENU] key. The SAVE confirmation window appears.

SAVE ?
YES
NO
CANCEL

SAVE confirmation window

11. With YES selected, press the [ENT] key to save the data.

4.3 System Settings

1. Press the [MENU] key to open the main menu.
2. Press the [6] key to open the SYSTEM SETTINGS sub-menu.

[SYSTEM SETTINGS]
1 SET I/O PORT
2 SET CHANNEL
3 SET LR MODE
4 SET OTHER I/O
5 SET BUZZER

SYSTEM SETTINGS sub-menu

3. Press the [1] key to display the SET I/O PORT sub-menu.

[SET I/O PORT]

1 I/O SPEED
2 I/O FUNCTION
3 I/O PRIORITY
4 SET LAN (IP ADDR)

SET I/O PORT sub-menu

4. Press the [1] key to display the I/O SPEED window.

[I/O SPEED] [NEXT] key [I/O SPEED]

PC I/O : 38.4 k +- LR : 38.4 k +-
SNSR1: 38.4 k +- BCON : 4800 +-
SNSR2: 38.4 k +- EXTRA1 : 38.4 k +-
SNSR3: 38.4 k 1 2+ - XTRA I/O : 4800 1 +2-
[SFT] +[NENT]
key

I/O SPEED window

26

More user manuals on ManualsBase.com

 5. Select the appropriate data transmission rate from 4800 bps and 38.4 kbps for
PC I/O, SNSR 1, SNSR 2, SNSR 3, LR, BCON (beacon receiver), EXTRA1 and
EXTRA2, by pressing the [SFT] key. To select each item, press the [NEXT] key.
To go backward, press the [NEXT] key while pressing the [SFT] key.
6. Press the [ENT] key to return to the SET I/O PORT sub-menu.
7. Press the [2] key to display the I/O FUCTION window.

[I/O FUNCTION]
PORT LR: EXT DISP + -

I/O FUNCTION window

8. Press the [SFT+/-] key to select EXT DISP or LR, depending on equipment
connected.
EXT DISP: External display, such as radar, ECDIS
LR: Long range communication, such INMARSAT communication equipment
9. Press the [ENT] key to return to the SET I/O PORT sub-menu.
10. Press the [3] key to display the I/O PRIORITY window.

[I/O PRIORITY]
1 L/L COG SOG
2 HDG
3 ROT
4 AIS

I/O PRIORITY window

11. Press the [1] key to display the L/L COG SOG window.

[L/L COG SOG]

SN1: 1 SN2: 2
SN3: 3
EX1 : 4 LR : 5
PC : 6 LAN: 7

DEFAULT: [CLR]

L/L/COG/SOG PRIORITY window

27

More user manuals on ManualsBase.com

 12. Set L/L position, COG and SOG data priority with the numeric keys according to
sensors connected.
COG: Course over ground
SOG: Speed over ground
13. Press the [ENT] key to return to the I/O PRIORITY window.

Note: If you have entered 8, 9 or the same value for more than one item at step
12, the following error message appears. In this case, press the [ENT]
key and set the priority correctly.

[ERROR] [ERROR]
CAN NOT INPUT OUT OF RANGE !
SAME VALUE ! PRIORITY: 1-7

ESC: [ENT] ESC: [ENT]

ERROR message
14. Set the priority for HDG and ROT similar to how you did for “L/L COG SOG”.
The priority of heading data entered from the AD-10 IN port is the lowest.
15. To set the priority of AIS, press the [4] key to choose AIS.

[AIS]
RESPONSE:PC +-
--------------------
EX1 : ENBL +-
LR : ENBL +-
PC : ENBL + -
LAN: ENBL +-
DEFAULT: [CLR]

AIS PRIORITY setting window

16. With RESPONSE selected, press the [SFT] key to select PC, NONE, LAN, EX1
or LR as appropriate.
Set an output port for response from other party after you transmit messages or
interrogation from the PC, ECDIS, LR, or LAN.
NONE : No output for response
PC : Output to PC I/O port
LAN : Output to LAN port
LR : Output to LR or ECDIS/RADAR port
EX1 : Output to EXTRA1 port
The PC I/O port provides RS-422 and RS-232C terminals. For example, to
connect a PC for pilot, connect it to the RS-422 terminal and set 34.8 Kbps for bit
rate on the PC I/O option in the I/O SPEED window.
17. Press the [NEXT] key to select EX1, LR, PC or LAN.
18. Press the [SFT] key to select ENBL (enable) or DSBL (disable) as appropriate.
This setting is for communication between FA-100 and each external equipment.
“DSBL” disables communication with selected item.
19. Press the [ENT] key and then [MENU] key to return to the SET I/O PORT
sub-menu.

28

More user manuals on ManualsBase.com

 20. Press [4] key to display the SET LAN (IP ADRS) window.

[SET LAN (IP ADRS)]

IP ADDRESS:
000-000-000-000
SUB NET MASK:
000-000-000-000

PORT NO. 10000

SET LAN (IP ADDR) window

21. If the FA-100 is connected to a network, enter IP address, sub net mask and
port number with the numeric keys and the [NEXT] key.
22. Press the [ENT] key and then the [MENU] key to return to the SYSTEM
SETTINGS sub-menu.
23. Press the [4] key to display the SET OTHER I/O window.

[SET OTHER I/O]

AD-10: DSBL +-
ROT : 01 SEC

SET OTHER I/O window

24. Select or set other I/O as follows.

1) AD-10: Select ENBL to use AD-10 format gyrocompass signal.
2) ROT: Set smoothing time (1 to 10 seconds) of the ship’s rate of turn if you are
using a ROT meter. This time is used to smooth the variations of data from the
AD-100 for calculation of ROT.
3) Press the [ENT] key to register setting. The display returns to the SYSTEM
SETTINGS sub-menu.
25. Press the [MENU] key. The following confirmation window appears.

SAVE ?
YES
NO
CANCEL

SAVE confirmation window

26. Select YES and press the [ENT] key. The main menu appears.

29

More user manuals on ManualsBase.com

 This page is intentionally left blank.

More user manuals on ManualsBase.com

 A-1
24AA-X-9854 -1 1/1
ＰＡＣＫＩＮＧ ＬＩＳＴ
FA-100-J/E,FA-100-J/E-HK
N A M E O U T L I N E DESCRIPTION/CODE № Q'TY
ユニット UNIT
ﾄﾗﾝｽﾎﾟﾝﾀﾞ部 FA-100

1
TRANSPONDER UNIT
000-053-889 **
工事材料 INSTALLATION MATERIALS CP24-00102
ｺﾈｸﾀﾌｰﾄﾞ(XM2) XM2S-0912

1
HOUSING CASE
000-145-422
ｹｰﾌﾞﾙ組品MJ MJ-A3SPF0015-035

1
CABLE ASSY.
000-137-340
ｺﾈｸﾀ(XM2) XM2A-0901

1
CONNECTOR(XM2)
000-111-785
図書 DOCUMENT
装備要領書 IMJ-44170-*

1
INSTALLATION MANUAL
000-809-324 **
取扱説明書 OMJ-44170-*

1
OPERATOR'S MANUAL
000-809-322 **

1.ｺ-ﾄﾞ番号末尾の[**]は、選択品の代表型式/ｺｰﾄを表します。
CODE NUMBER ENDED BY "**" INDICATES THE NUMBER OF TYPICAL MATERIAL.

（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

24AA-X-9854
More user manuals on ManualsBase.com
 A-2
24AA-X-9851 -4 1/1
ＰＡＣＫＩＮＧ ＬＩＳＴ
CB-100-A､CB-100-A-HK
N A M E O U T L I N E DESCRIPTION/CODE № Q'TY
ユニット UNIT
接続箱 CB-100-A

1
JUNCTION BOX UNIT
000-053-873 **
工事材料 INSTALLATION MATERIALS CP05-08701
+ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ 5X20 SUS304 1ｼｭ

4
+TAPPING SCREW
000-802-081

1.ｺ-ﾄﾞ番号末尾の[**]は、選択品の代表型式/ｺｰﾄを表します。
DOUBLE ASTERISK DENOTES COMMONLY USED EQUIPMENT.

（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

24AA-X-9851
More user manuals on ManualsBase.com
 A-3
ＰＡＣＫＩＮＧ ＬＩＳＴ 24AA-X-9853 -3 1/1

GVA-100
N A M E O U T L I N E DESCRIPTION/CODE № Q'TY
ユニット UNIT
複合空中線部 GVA-100
1
GPS/VHF COMBINED ANTENNA
000-053-810
工事材料 INSTALLATION MATERIALS CP24-00141
ｺﾈｸﾀ(N) N-P-8DFB 座金付き
2
CONNECTOR
000-140-463

ｺﾝﾍﾞｯｸｽ CV-200HT
2
PLASTIC BAND
000-809-226

ｱﾝﾃﾅ取付金具 24-003-3015-0
2
ANTENNA FIXING BRACKET
100-302-670

ﾐｶﾞｷ平座金 M8 SUS304
4
FLAT WASHER
000-864-130

六角ﾅｯﾄ １種 M8 SUS304
8
HEX.NUT
000-863-110

（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

24AA-X-9853
More user manuals on ManualsBase.com
 A-4
CODE NO. 004-365-780 20AG-X-9403 -1
TYPE CP20-01111 1/1

マスト取付金具
工事材料表 MAST FIXTURE

INSTALLATION MATERIALS
番 号 名 称 略 図 型名／規格 数量 用途／備考
NO. NAME OUTLINE DESCRIPTIONS Q'TY REMARKS
ﾊﾟｲﾌﾟ 20-007-3011-2
1 1
PIPE
CODE NO. 100-183-262

取付補助金具 20-007-3012-1
2 1
INSTALLING SPACER
CODE NO. 100-183-271

ﾊﾟｰｶｰｸﾗﾝﾌﾟ NO.6348 SUS303

3 2
HOSE CLAMP
CODE NO. 000-805-906

20AG-X-9403

ＦＵＲＵＮＯ ＥＬＥＣＴＲＩＣ ＣＯ ．，ＬＴＤ.

（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

More user manuals on ManualsBase.com

 A-5
ＰＡＣＫＩＮＧ ＬＩＳＴ 24AA-X-9852 -5 1/1

PR-240-CE
N A M E O U T L I N E DESCRIPTION/CODE № Q'TY
ユニット UNIT
AC-DC電源 PR-240-CE

1
POWER SUPPLY UNIT
000-053-879
工事材料 INSTALLATION MATERIALS CP24-00151
PR-240-CE電源変更手順書 C52-00205-A

1
POWER MODIFICATION PROCEDURES
000-147-013
ﾃﾞﾝｹﾞﾝﾊﾘﾏｰｸ 24-003-4101-3

1
POWER LABEL
100-299-773
+ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ 4X16 SUS304 1ｼｭ

4
+TAPPING SCREW
000-802-080

（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

24AA-X-9852

More user manuals on ManualsBase.com

 A-6
CODE NO. 20AG-X-9404 -1
TYPE 1/1

GP-80,GP-90,SC-55,GP-3500/F
工事材料表 GP-1850,GP-1650,FA-100,GP-1640/F
SC-60/120,GD/GP-280/680/380
INSTALLATION MATERIALS
番 号 名 称 略 図 型名／規格 数量 用途／備考
NO. NAME OUTLINE DESCRIPTIONS Q'TY REMARKS
ｱﾝﾃﾅｹｰﾌﾞﾙ組品 8D-FB-CV *30M* 選択 TO BE SELECTED

1 1
ANTENNA CABLE ASSY.
CODE NO. 000-111-547

ｹｰﾌﾞﾙ組品 8D-FB-CV *50M* 選択 TO BE SELECTED

2 1
CABLE ASSY.
CODE NO. 000-117-599

20AG-X-9404

ＦＵＲＵＮＯ ＥＬＥＣＴＲＩＣ ＣＯ ．，ＬＴＤ.

（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

More user manuals on ManualsBase.com

 A-7
CODE NO. 004-372-420 20AG-X-9405 -1
TYPE CP20-01701 1/1

工事材料表
INSTALLATION MATERIALS
番 号 名 称 略 図 型名／規格 数量 用途／備考
NO. NAME OUTLINE DESCRIPTIONS Q'TY REMARKS
変換ｹｰﾌﾞﾙ組品 NJ-TP-3DXV-1
1 2
CONVERT CABLE ASSY.
CODE NO. 000-123-809

ﾋﾞﾆｰﾙﾃｰﾌﾟ NO360 02X19X10000

ｸﾛ ｴｽﾛﾝ
2 1
VINYL TAPE
CODE NO. 000-835-215

ｺﾈｸﾀ(N) N-P-8DFB
3 1
CONNECTOR
CODE NO. 000-111-549

絶縁ﾃｰﾌﾟ Uﾃｰﾌﾟ 0.5X19X5M

4 1
SELF-BONDING TAPE
CODE NO. 000-800-985

20AG-X-9405

ＦＵＲＵＮＯ ＥＬＥＣＴＲＩＣ ＣＯ ．，ＬＴＤ.

（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

More user manuals on ManualsBase.com

 A-8
CODE NO. 004-365-780 20AG-X-9403 -1
TYPE CP20-01111 1/1

マスト取付金具
工事材料表 MAST FIXTURE

INSTALLATION MATERIALS
番 号 名 称 略 図 型名／規格 数量 用途／備考
NO. NAME OUTLINE DESCRIPTIONS Q'TY REMARKS
ﾊﾟｲﾌﾟ 20-007-3011-2
1 1
PIPE
CODE NO. 100-183-262

取付補助金具 20-007-3012-1
2 1
INSTALLING SPACER
CODE NO. 100-183-271

ﾊﾟｰｶｰｸﾗﾝﾌﾟ NO.6348 SUS303

3 2
HOSE CLAMP
CODE NO. 000-805-906

20AG-X-9403

ＦＵＲＵＮＯ ＥＬＥＣＴＲＩＣ ＣＯ ．，ＬＴＤ.

（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

More user manuals on ManualsBase.com

More user manuals on ManualsBase.com
 D-2

Oct. 21,'02

More user manuals on ManualsBase.com

 D-3

Oct. 21,'02

More user manuals on ManualsBase.com

 D-4

Sep.29'05

More user manuals on ManualsBase.com

 D-4a

May 20 '03

More user manuals on ManualsBase.com

 D-5

Feb.22'05

More user manuals on ManualsBase.com

 D-6

Jan. 9,'03

More user manuals on ManualsBase.com

 D-7

Jan. 9, '03

More user manuals on ManualsBase.com

 D-8

H.Hayashi
Mar.11'04

More user manuals on ManualsBase.com

 D-9

Feb.02'05

More user manuals on ManualsBase.com

 D-10

Nov.28'03

More user manuals on ManualsBase.com

 D-11

Y. Hatai

More user manuals on ManualsBase.com

 D-12

Oct.02'03

More user manuals on ManualsBase.com

 1 2 3 4 5 6
S-1
接続箱 CB-100
選択 トランスポンダ部 J1
TD3-A 1
XM2A-3710 24S0058,3.3m
ｱｵ/ｱｶ1 BLU/RED1 1
J1 JUNCTION BOX
TD3-A 1
SELECT SNSR3
GPSアンテナ
TRANSPONDER UNIT IEC61162-1/2
TD3-B 2
P
ｱｵ/ｸﾛ1 BLU/BLK1 2 TD3-B 2
RD3-A 3 ﾓﾓ/ｱｶ1 PNK/RED1 3 GNDISO 3 EXTERNAL
複合空中線部 GPS ANTENNA FA-100 RD3-B 4
P
ﾓﾓ/ｸﾛ1 PNK/BLK1 4 RD3-A 4 1 TTYCS-1Q,φ13.5 *1
GPS/VHF ANTENNA OR CO-0.2x2P (MAX.30m) GPS *3
GPA-017S SNSR2 TD2-A 5 ﾐﾄﾞﾘ/ｱｶ1 GRN/RED1 5 RD3-B 5 2
P
GVA-100 OR TD2-B 6 ﾐﾄﾞﾘ/ｸﾛ1 GRN/BLK1 6 GNDISO 6 3,4
GSC-001 IEC61162-1/2
RD2-A 7 ﾀﾞｲ/ｱｶ1 ORG/RED1 7 TD2-A 7
P
VHFアンテナ RD2-B 8 ﾀﾞｲ/ｸﾛ1 ORG/BLK1 8 TD2-B 8
A 150M-W2VN VHF ANTENNA TD1-A 9 ﾊｲ/ｱｶ1 GRY/RED1 9 GNDISO 9
SNSR1 P TTYCS-1Q,φ13.5 *1 GYRO OR
OR *2 1
TD1-B 10 ﾊｲ/ｸﾛ1 GRY/BLK1 10 RD2-A 10

0.2m
FAB-151D
150M-W2VN IEC61162-1/2 2 OR CO-0.2x2P (MAX.30m) THD [IMO Res. MSC.116(73)]
*2 RD1-A 11 ｱｵ/ｱｶ2 BLU/RED2 RD2-B 11
OR

NJ-TP-3DXV-1
P 3,4
TNC-J-3 RD1-B 12 ｱｵ/ｸﾛ2 BLU/BLK2 J2 GNDISO 12
FAB-151D

1m,φ5.3
1 TD1-A 13
GSC-001 2 TD1-B 14
BEACON TD5-A 13
P
ﾓﾓ/ｱｶ2 PNK/RED2 3 GNDISO 15
TTYCS-1Q,φ13.5 *1
*5 *4
1

M-P-7
VHF-ANT RTCM SC-104
TD5-B 14 ﾓﾓ/ｸﾛ2 PNK/BLK2 4 RD1-A 16 ROT OR LOG
RD5-A 15 ﾐﾄﾞﾘ/ｱｶ2 GRN/RED2 5 2 OR CO-0.2x2P (MAX.30m)
RD1-B 17
P 3,4
M-P-7 J1 RD5-B 16 ﾐﾄﾞﾘ/ｸﾛ2 GRN/BLK2 6 GNDISO 18
RG-10/UY *1 ANT LR OR ECDIS/RADAR TD4-A 17 ﾀﾞｲ/ｱｶ2 ORG/RED2 7 TD5-A 19
N-P-8DFB

P
E TD4-B 18 ﾀﾞｲ/ｸﾛ2 ORG/BLK2 8 TD5-B 20
IEC61162-1/2
NJ-TP-3DXV-1 RD4-A 19 ﾊｲ/ｱｶ2 GRY/RED2 9 GND 21
N-J-3 0.8m

GPS-ANT P TTYCS-1Q,φ13.5 *1
1m,φ5.3 RD4-B 20 ﾊｲ/ｸﾛ2 GRY/BLK2 10 RD5-A 22 DGPS受信機
8D-FB-CV,30/50m(L>20m) *2 OR CO-0.2x2P (MAX.30m)
N-P-8DFB J2 11 RD5-B 23 DGPS BEACON RECEIVER
RG-10/UY,MAX.20m *1
EXTRA1 I/O TD6-A 21
P
ｱｵ/ｱｶ3 BLU/RED3 12 GND 24
TTYCS-4,φ16 *1
IEC61162-1/2 TD6-B 22 ｱｵ/ｸﾛ3 BLU/BLK3 TD4-A 25 LONG RANGE COMMUNICATION OR
P (MAX.30m)
RD6-A 23 ﾓﾓ/ｱｶ3 PNK/RED3 J3 TD4-B 26 RADAR/ECDIS
P
N-P-8DFB

RD6-B 24 ﾓﾓ/ｸﾛ3 BLU/BLK3 1 GNDISO 27

N-P-8DFB

M-P-3 2 RD4-A 28
B *2 1m VHF-ANT
P
分配器 PC I/O TD8-A 25
P
ﾐﾄﾞﾘ/ｱｶ3 GRN/RED3 3 RD4-B 29
8D-FB-CV,30/50m(L>20m) TD8-B 26 ﾐﾄﾞﾘ/ｸﾛ3 GRN/BLK3 4 GNDISO 30
RG-10/UY,MAX.20m *1 N-J-3 1m DISTRI- TTYCS-4,φ16 *1
BUTOR (RS-422) RD8-A 27
P
ﾀﾞｲ/ｱｶ3 ORG/RED3 5 TD6-A 31
P (MAX.30m)
EXTRA I/O (IEC61162-1/2)
DB-1 TNC-P-3 RD8-B 28 ﾀﾞｲ/ｸﾛ3 ORG/BLK3 6 TD6-B 32
1m
GPS-ANT (RS-232C) TD 29 ﾊｲ/ｱｶ3 GRY/RED3 7 GNDISO 33
P
RD 30 ﾊｲ/ｸﾛ3 GRY/BLK3 8 RD6-A 34 パイロットプラグユニット
P
ALARM OUT ALOL 31 ｱｵ/ｱｶ4 BLU/RED4 9 RD6-B 35 PILOT PLUG UNIT
P OP24-3 *2 *1 *8
(CONTACT SIG.) ALOH 32 ｱｵ/ｸﾛ4 BLU/BLK4 10 GNDISO 36
TTYCS-4,φ16 *1 (MAX.30m)
206486-1 206485
ALOC 33 ﾓﾓ/ｱｶ4 PNK/RED4 11 TD8-A 37 1 TX A 1 PC
P P
1PPSIN 34 ﾓﾓ/ｸﾛ4 PNK/BLK4 12 TD8-B 38 2 TX B 4
NC 35 ﾐﾄﾞﾘ/ｱｶ4 GRN/RED4 13 GNDISO 39 3 RX A 5
P
GND 36 ﾐﾄﾞﾘ/ｸﾛ4 GRN/BLK4 14 RD8-A 40 4 RX B 6
P
FG 37 RD8-B 41 5 SHIELD 9
船内主電源及び GNDISO 42
非常電源
SHIP'S MAIN AND EXTRA I/O TTYCS-1Q,φ13.5 *1
POWER J2 D-SUB 9P TD(232C) 43 (MAX.15m) PC I/O (RS-232C)
EMERGENCY SOURCE *7 TTYCS-1Q,φ13.5 *1
MJ-A3SPF0015,3.5m,φ6
MJ-A3SPFD J1(FM-C3MR) IEC61162-1 TD7-A 1 RD(232C) 44
OR CO-0.2x2P (MAX.30m) TTYCS-1Q,φ13.5 *1
12-24VDC シロ WHT 1 (+) TD7-B 2 AOL 45 ALARM
(02S4100-0) OR CO-0.2x2P
クロ BLK 2 (-) AOH 46
3 GND AOC 47
C AC/DC電源ユニット GND 8 1PPSIN 48
AC/DC POWER SUPPLY 24P0020
FG 9 24P0031
PR-240-CE *2 UNIT LAN(10B-T)
100-115/200-230VAC *DPYC-1.5 AC IN DC OUT (+) D-SUB 9P EXTERNAL EQUIPMENT
J3
φ1,50/60Hz LAN CABLE *1
(-) IEC61162-4 LATX-H 1 LAN (IEC61162-1)
P CATEGORY 4 OR ABOVE
(10BASE-T) LATX-L 2
(MAX.30m)
LARX-H 3
P
LARX-L 4
PE, V-2.0SQ *1 GND 8
注記 保護アース FG 9
＊１）造船所手配。
AD-10 IN
＊２）オプション。 J4 D-SUB 9P *6
TTYCS-1Q,φ13.5 *1
＊３）外部GPS受信機からのL/Lデータ入力が必要。 GDAT-H 1 AD-100 GYRO
*6 GDAT-L 2 OR CO-0.2x2P
＊４）SOG、COGが外部GPSから出力可能な場合は不要。 GCK-H 3
＊５）ROTは接続可能な場合のみ。 GCK-L 4
＊６）AD-10ﾌｫｰﾏｯﾄ（GYRO-IEC61162がないときに必要） GND 8
FG 9
＊７）12V仕様の場合、ケーブル最大長は0.5m。
AUX-1
＊８）AMP社製。
D J5
LOG 1
NOTE: LOG-G 2 NOT USED
*1: SHIPYARD SUPPLY. PRTX 6
PRRX 7
*2: OPTION. GND 8
*3: POSITION DATA (L/L) IS REQUIRED BY EXTERNAL GPS RECEIVER. FG 9 IEC61162-1: 4800BPS
*4: SPEED LOG IS NOT REQUIRED WHEN SOG (SPEED OVER GROUND) AND AUX-2 IEC61162-2: 38.4KBPS
J6
COG (COURSE OVER GROUND) DATA ARE FED BY EXTERNAL GPS RECEIVER. GPEXT-A 1 NOT USED IEC61162-4: 10BASE-T
*5: ROT (RATE OF TURN) INDICATOR CAN BE CONNECTED IF PROVIDED. GPEXT-B 2
*6: GYRO CONVERTOR AD-100 IS REQUIRED WHEN GYRO SIGNAL (IEC61162) GPEXR-A 3 DRAWN TYPE
GPEXR-B 4 Apr. 16 '04 K.MIYAZAWA FA-100
IS NOT AVAILABLE. GND 8 CHECKED 名前
TAKAHASHI.T 国際船舶自動識別装置
*7: MAX. CABLE LENGTH IS 0.5m FOR 12 VDC SPECIFICATIONS. 24P0025 FG 9 APPROVED
*8: SUPPLIED BY AMP INC. Y. Hatai 相互結線図
SCALE MASS NAME
kg U-AIS TRANSPONDER
CO-0.2x2P: CO-SPEVV-SB-C 0.2x2P,φ10.5 DWG. No.
C4417-C02- K INTERCONNECTION DIAGRAM