2020 EDITION IV
GARNET EDGE HOME SEARCH HOME
HOME INFO HUB THE GARNET EDGE NEWSLETTER 2020 EDITION IV
BLASTTALK: SPOT ABRASIVE BLASTING AND THE RIGHT ABRASIVES
BlastTalk: Spot Abrasive Blasting and the right Abrasives
The repair of damaged coated steel surfaces is a difficult and time-consuming task. Many of
these difficulties stem from the repair methods used and many asset owners take these
repairs for granted.
They opt to use sub-standard repair methods such as chipping or mechanical power-tooling due
to accessibility and perceived time, material, labor and equipment savings.
These sub-standard methods only partially remove corrosion products and damaged coatings
which in turn, eventually results in premature failure to the touch-up coatings that were applied
over these repair areas. Consequently, this results in the process having to be repeated again and
again.
When the initial coating system was applied over the original surfaces, abrasive blasting would be
the most preferred method and these substrates would be cleaned to White (Class Sa 3) or Near-
White (Class 2½). If spot repairs are necessary, it is important that corrosion products in the
coating breaks must be completely removed and the pit is corrosion free.
It is also very important that the damaged coating be removed to the point where it is solid, intact
and tightly adhered to the surface. Otherwise, failure will continue to occur at the same spot.
It is therefore essential that the coating be tapered from the corrosion repair area out to the solidUS
CONTACT
adhered area creating a featheredge at the junction between the steel and the old coating. This
transition zone is not only necessary for a proper repair but also provides a much better
appearance since there are no jagged rough edges to give the appearance of a patch job.
Therefore, Spot Abrasive blasting is the ideal repair method to address these concerns as it can
effectively clean the corroded areas to the highest-class standards and create the interface
between the blasted area and old coating edge.
Do you have a technical question
you'll like us to explore on
BlastTalk? Write to us
Spot blasting has also been included in many specifications where new project coating systems
need to be repaired due to erection damages.
To achieve optimal performance, the spot blasting procedure outlined in these specifications is to
spot blast the rusty/damaged areas to minimum Class 2½, feather the intact coating edges, and
light sweep blast to abrade the rest of the intact coating to remove dirt, chalk and other
contaminants.
In numerous instances, asset owners may also wish to apply a full new coat over the intact good
older areas just for aesthetic reasons. In these situations, lightly abrading the existing intact
coating with a finer mesh sized abrasive such as GMA SpeedBlast™ garnet or Newsteel™ garnet,
will provide sufficient mechanical bond capability for the next fresh paint layer.
To round up the main procedure in a spot blasting process,
the following key points are recommended:
Use a predominately finer sized abrasive, such as 60 or 80 mesh so as to minimise the impact
of larger particles on surrounding intact coatings. This also known as over-blast and may result
in micro fractures in the coating film.
Blast the corroded areas to the specified standard by normal operator methods. Holding the
blast nozzle close-up and perpendicular allows for the larger and heavier abrasive particles to
break up heavy rusts and damaged coated areas.
CONTACT US
Following this, back off the blast nozzle to between 1 to 1.3m (3 or 4 ft) and feather the intact
coating edge at an oblique angle to the surface.
Clean and abrade the solid coating surrounding the repair, continue to use the finer mesh
abrasive by sweeping the existing coating both at a distance and at an oblique angle to prevent
direct impact from the larger particles.
By Saravanan Madavamani, GMA Asia Pacific
PREVIOUS NEXT
CONTACT US
Related Articles
BLASTTALK
BlastTalk: Clearing the confusion on surface chlorides testing
CONTACT US
BLASTTALK
BlastTalk: Six tips for maximising the efficiency of your blasting operation
CONTACT US
BLASTTALK
BlastTalk: Advantages of finer grade garnet
CONTACT US
BLASTTALK
Getting to know your blasting medium
HOME
ABOUT GMA
OUR RESPONSIBILITY
BLASTING ABRASIVES
WATERJET CUTTING
CONTACT US
SPECIALTY APPLICATIONS & MINERALS
INFO HUB
CONTACT US
FOLLOW US
NEWSLETTER
Subscribe to our e-newsletter for the latest news and events at GMA.
First name
Last name
Company
Email
I'm not a robot
reCAPTCHA
Privacy - Terms
SUBSCRIBE
Copyright © 2005-2023 GMA Garnet Pty Ltd. All Rights Reserved
Legal Notice | Privacy Policy
CONTACT US
