SENSING

TOMORROW LMP633-NLN Piezoresistive silicon submersible level transmitter

Product introduction

Description

Submersible level transmitter

LMP633 Submersible level transmitter is designed for dealing with

the most severe demanding level measurement conditions. The
sensor adopts the most advanced micro-processor technology with
comprehensive linear error compensation and temperature error
compensation to assure the highest precision of measuring result.
The probe adopts full potting condensation-preventing technology,
safe and reliable dual-seal design and fully welding technology with
solid stainless steel body to assure long term stability and
permanent air tightness. Signal transmitting module adopts transient
voltage resistance protective circuits to assure operation regularly
even under the harsh surge voltage environment. The seal of the
cable adopts intensive cone plug sealing design to assure the long
working life even under large mechanical load conditions during the
installation and long-term use. LMP633 Submersible level
transmitter is the optimal choice to satisfy all of high demand level
measuring applications.

Main parameters Application

Pressure types Gauge pressure Level measurement in container, others

Measuring range 1 mH2O - 200 mH2O, Please refer to
the ordering information chapter
Output signal 4-20mA,4-20mA+HART,0.5-4.5VDC Approvals
Modbus-RTU/RS485, others
Reference ±0.2% URL, ±0.5% URL
accuracy

Measuring medium

Water, waste water, oil

Disclaimer: all the data used in the product description is not legally binding. Relevant technical details may be changed due to further improve

2015.12.V1.0 .1.
 SENSING
TOMORROW LMP633-NLN Piezoresistive silicon submersible level transmitter

Technical specifications

Measuring range and limit

Nominal value Smallest calibratable span Lower range limit (LRL) Upper range limit (URL) Overload limit
20kPa 10kPa 0kPa 20kPa 30kPa
35kPa 20kPa 0kPa 35kPa 52.5kPa
100kPa 35kPa 0kPa 100kPa 150kPa
200kPa 100kPa 0kPa 200kPa 300kPa
350kPa 200kPa 0kPa 350kPa 525kPa
700kPa 350kPa 0kPa 700kPa 1050kPa
1MPa 500kPa 0kPa 1MPa 1.5MPa
1.7MPa 1MPa 0kPa 1.7MPa 2.55MPa
* 3.5MPa 1.7MPa 0kPa 2MPa 5.25MPa
* Due to the seal structure limit of the products, the upper range limit(URL) is lower than the nominal value(see chart above).
(1MPa = 102 mH2O@4℃)
The unit of the measuring range above can be converted into mH2O@4℃, mmH2O@4℃, inH2O@4℃ , m, mm and mHg@0℃.
Please provide the density of measuring medium if the unit is m, mm. Other measuring range is available according to
requirements.

Standard specifications and reference conditions Power supply effects

Test standard: GB/T28474 / IEC60770 Zero and span change should not be more than ± 0.005%
Zero based-calibration span, Linear output, Silicone oil URL/V
filling, 316L stainless steel isolation diaphragm.

Loading effects
Performance specifications

Zero and span change should not be more than ± 0.05%

The overall performance including but not limited to URL/kΩ
【 reference accuracy 】, 【environment temperature
effects】and other comprehensive error
Typical accuracy: ±0.2URL (HART output accuracy: Durability performance
±0.1URL)
Stability: ±0.2% URL/ year All the measuring range, working life> 10 million pressure
circulation@25℃
Reference accuracy
Vibration effects

Including linearity, hysteresis and repeatability.

calibration temperature: 20 ℃ ± 5 ℃ According to IEC61298-3/GB/T 18271.3 testing 20g (5-
Linear Typical ±0.2%URL (HART Nominal value: 2000HZ, Max imum vibration value< 3mm)
output output accuracy: 20kPa、35kPa、
accuracy ±0.1% URL) 100kPa、200kPa
Output signal
Max/ ±0.5% URL 350kPa、700kPa
Voltage 1MPa、1.7MPa
output 3.5MPa Signal Type Output
4-20mA Linearity Two wire

Ambient temperature effects 4-20mA+HART Linearity Two wire

0.5-4.5VDC Linearity Three wire
Modbus-RTU/RS485 Linearity Four wire
Within the range - 20-80 ℃ total impact ±0.2%URL/10k

Disclaimer: all the data used in the product description is not legally binding. Relevant technical details may be changed due to further improve

2015.12.V1.0 .2.
 SENSING
TOMORROW LMP633-NLN Piezoresistive silicon submersible level transmitter

Performance specifications

Insulation resistance Environment condition

≥20MΩ@ , 100VDC Items Operational condition

Working temperature - 1 0- 70℃
Storage temperature - 3 0- 80℃
Damping time
Media temperature - 10 - 70℃
Proction class IP 68
Total damping time constant: equal to the sum of damping
time of amplifer and sensor capsule Dangerous condition ExiaIICT4(GYB13.1139X) *
Damping time of amplifer : 0-100S adjustable * Only for 4-20mA output
Startup after power off : ≤3S (HART output time: ≤ 6S)
Normal services after data recovery：≤4S (HART output
time≤31S)

Technical Specifications

Signal output 4-20mA 4-20mA+HART * 0.5-4.5VDC 0.5-4.5VDC(proportional output) R S485

Power supply 10-30VDC 10.5/16.5-55VDC 6-30VDC 5VDC 5VDC/9-30VDC

Allowed current ≤20.8mA ≤3.5mA ≤7mA

Load resistance(Ω) <(U-10)/0.0208 <(U-10.5)/0.0208 ** ≥5k, recommend 100k /

Transmission distance <1000m <5m <1200m

Power consumption ≤500mW(20.8mA output@24VDC) ≤17.5mW(0.5-4.5VDC output@5VDC) ≤168mW(RS485

output@24VDC)
* For this output type, the load resistance value in communication is 250Ω
** The load resistance value 0-2119Ω is in nominal working condition, 250-600Ω is for HART communication

EMC environment(except for RS485 signal output)

NO. Test items Basic standards Test conditions Performance level

1 Radiated interference GB/T 9254/CISPR22 30MHz-1000MHz OK
2 Conducted interference (DC power port) GB/T 9254/CISPR22 0.15MHz-30MHz OK
3 Electrostatic discharge immunity test (ESD) GB/T 17626. 2 /IEC61000-4- 2 4kV ( Contact ) ,8kV(Air) B(Note2)
4 Immunity to radio frequency EM-fields GB/T 17626. 3 /IEC61000-4- 3 10V/m(80MHz-1GHz) A(Note1)
5 Power frequency magnetic field Immunity GB/T 17626.8/IEC61000-4-8 30A/m A(Note1)
test
6 Electrical fast transient / Burst Immunity GB/T 17626.4/IEC61000-4-4 2kV(5/50ns,100kHz) B(Note2)
Test
7 Surge immunity requirements GB/T 17626.5/IEC61000-4-5 1kV(Line to line) B(Note2)
2kV(Line to ground)
(1.2us/50us)
8 Immunity to conducted disturbances GB/T 17626.6/IEC61000-4-6 3V(150kHz-80MHz) A(Note1)
induced by radio frequency fields
(Note 1)Performance level A: The preformance within the limits of normal technical specifications.
(Note 2)Performance level B: Temporary reduction or loss of functionality or preformance, it can restore itself. The actual
operating conditions, storage and data will not be changed.

Disclaimer: all the data used in the product description is not legally binding. Relevant technical details may be changed due to further improve

2015.12.V1.0 .3.
 SENSING
TOMORROW LMP633-NLN Piezoresistive silicon submersible level transmitter

Product selection instruction

Sensor select instruction Electrical connection

Code Nominal Description Code Item Description

value N1 Electrical Diameter of PUR cable: (7.5±0.2)mm
L203G 20kPa Range 0-20kPa connection
N2 Diameter of PTFE cable: (7.5±0.2)mm
Smallest calibratable span 10kPa
L353G 35kPa Range 0-35kPa
Smallest calibratable span 20kPa
L104G 100kPa Range 0-100kPa Cable(N1/N2)
Smallest calibratable span 35kPa
L204G 200kPa Range 0-200kPa,
Smallest calibratable span 100kPa
L354G 350kPa Range 0-350kPa
Smallest calibratable span 200kPa
S704G 700kPa Range 0-700kPa
Smallest calibratable span 350kPa
L105G 1MPa Range 0-1MPa
Smallest calibratable span 500kPa
L175G 1.7MPa Range 0-1.7MPa
Smallest calibratable span 1MPa
L355G 3.5MPa Range 0-2MPa
Smallest calibratable span 1.7MPa

Code Parts Description

S Sensor O-ring, FKM (Operating temperature Electrical connection
seal range: -20℃-200℃)
F Stainless steel welding Cable output

Seal (S) Red

Blck
Filter
Blue
Yellow

Label Two wires Three wires Four wires Modbus - RTU / RS485

Red Power+ Power+ Power+ Power+

Black Power- Power- Power- Power-
Blue Signal+ Signal+ A+
Yellow Signal- B-

！ The reference pressure of the gauge pressure transmitter is current

atmospheric pressure.
Please operate with care, prevent the filter dropping off and keep it dry

Disclaimer: all the data used in the product description is not legally binding. Relevant technical details may be changed due to further improve

2015.12.V1.0 .4.
 SENSING
TOMORROW LMP633-NLN Piezoresistive silicon submersible level transmitter

Product selection instruction

Transmission module Electrical connection

Code Description Code Item Description

F 4-20mA two wire,power supply: 10-30VDC 4 Material SUS304 stainless steel
H 4-20mA+HART two wire, power supply: 6 SUS316 stainless steel
16.5-55VDC
H28 Specification Diameter of submersible
5 0.5-4.5VDC three wire,power supply: probe:28mm
6-30VDC
6 0.5-4.5VDC ratiometric output three wire, power
supply:5VDC Probe diagram(H28)
R Modbus-RTU/RS485, four wire, power suply:
5VDC/9-30VDC

Fixed mounting accessory

Code Iterms Details

P1 Fixed Counter weight (To fix products in some
mounting areas of fast flow rate or medium with
large density)
P2 Cable clamp (To fix and support the
product)
P3 Threaded connection (To fix the top and
support the product)
P4 Threaded connection (To fix the bottom
and support the product )

Counter weight(P1), Cable clamp(P2), Threaded connection(P4)

Thread connection(P3)

2
5

7
3 6

4 3

1.Thread connection(P3) 4.Counter weightP1) *

2.Cable 5. Cable clamp(P2)
7.Threaded connection(P4)
3.Level transmitter 6. Protective sleeve
* The measurement results should consider the height error
of counter weight and sensing diaphragm to the bottom of
measured medium
Disclaimer: all the data used in the product description is not legally binding. Relevant technical details may be changed due to further improve

2015.12.V1.0 .5.
 SENSING
TOMORROW LMP633-NLN Piezoresistive silicon submersible level transmitter

Product drawing and dimension

Drawing and dimension (unit:mm) Counter weight drawing and dimension(P1)(unit:mm)

7.60 M22X1

28 27.80

*Show the distance from sensing diaphragm to the bottom of product

Weight: about 340g(without cable) Weight: about 500g

Cable Weight Table In order to prevent measurement errors caused by sideways

movement of product and ensure accuracy, you can add
Cable materia Weight/5m(kg)
additional counter weights by screwing together and then
Polyurethane(PUR) 0.32 connecting directly to the product. Each product can add
Polytetrafluoroethylen(PTFE) 0.41 three weights at the most.

Disclaimer: all the data used in the product description is not legally binding. Relevant technical details may be changed due to further improve

2015.12.V1.0 .6.
 SENSING
TOMORROW LMP633-NLN Piezoresistive silicon submersible level transmitter

Product drawing and dimension

Cable clamp(P2) drawing and dimension (Unit:mm) Thread connection P4 drawing and dimension (Unit:mm)

M22X1

M20X1.5

88
Weight: about 340g Weght:about 120g

Thread connection mounting(P3) drawing and dimension (Unit:mm)

G1-1/2
55

Weght:about 520g

Disclaimer: all the data used in the product description is not legally binding. Relevant technical details may be changed due to further improve

2015.12.V1.0 .7.
 SENSING
TOMORROW LMP633-NLN Piezoresistive silicon submersible level transmitter

Ordering information chapter

Item Parameters Code Instruction (*) fast delivery available

Model LMP633-NLN Piezoresisitive silicon submersible level transmitter
Sensor Separator - Detailed specifications as following
Pressure L203G Nominal value(URL): 20kPa
range code
L353G Nominal value(URL): 35kPa
L104G Nominal value(URL): 100kPa *
L204G Nominal value(URL): 200kPa *
L354G Nominal value(URL): 350kPa *
L704G Nominal value(URL): 700kPa *
L105G Nominal value(URL): 1000kPa *
L175G Nominal value(URL): 1700kPa *
L355G Nominal value(URL): 3.5MPa
Seal S O-ring, FKM: -10℃-120℃ *
material
F Stainless steel welding
Electrical Separator - Detailed specifications as following
connetion
Electrical N1 PUR cable diameter(7.5±0.2)mm *
connetion
N2 PTFE cable diameter(7.5±0.2)mm
Output Separator - Detailed specifications as following
Output F 4-20mA two wire,power supply: 10-30VDC *
signal
H 4-20mA+HART two wire, power supply:16.5-55VDC *
5 0.5-4.5VDC three wire, power supply:6-30VDC
6 0.5-4.5VDC ratiometric output three wire, power supply:5VDC *
R Modbus-RTU/RS485, four wire ,power suply:5VDC/9-30VDC
Probe Separator - Detailed specifications as following
Material 4 SUS304 Stainless steel *
6 SUS316 Stainless steel *
Specification H28 Submersible probe diameter 28mm *
Cable Separator - Detailed specifications as following
Cable length LXXX XXX Range:000-200, Eg.5m express as L005,10m express *
as L010,100m express L100,cable length allowed error rang:
0-0.2m
additional Separator - Detailed specifications as following
options
Fixed /P1 Counter weight (To fix products in some areas of fast flow rate *
mounting or medium with large density)
accessory
/P2 Cable clamp (To fix and support the product)

/P3 Threaded connection (To fix the top and support the product) *
/P4 Threaded connection (To fix the bottom and support the *
product )
Calibration
/Q1 According to user requirements
*
report

Disclaimer: all the data used in the product description is not legally binding. Relevant technical details may be changed due to further improve

2015.12.V1.0 .8.
 SENSING
TOMORROW LMP633-NLN Piezoresistive silicon submersible level transmitter

Ordering information chapter

Product /E1 Flame-proof certificate, ExdllCT6,NEPSI

certification
standards
/I1 Intrinsic safety certificate, ExiaIICT4, NEPSI *
/F3 CE certificate *

Approvals

Factory certificate Intrinsic safety certificate

Certification NEP S I
Certification organization Intertek
organization name
Quality management system ISO9001-2008
Licenses range LMP series pressure transmitter
Design and production of
Scope of certification Explosion-proof mark ExiaIICT4
pressure transmitter
Registration number 110804039 Ambient temperature -25-+60℃
Medium maximum +80℃
temperature
Registration number GYB13.1139X
Intrinsically safe Maximum input voltage:28VDC
CE
parameter description Maximum input current:93mA

Maximum input power:0.66w

Licence scope PRESSURE TRANSMITTER
Standard EN61000-6-2：2005 Maximum internal equivalent
parametersCi(nF):0.035
EN61000-6-4：2007
Maximum internal equivalent
Registered number AC/0100708 parametersLi(mH):≈0

SENSING
TOMORROW

Shanghai LEEG Instruments Co.,Ltd

ADD：No.100 Duhui Road, Minhang District, Shanghai China
Postcode:201109
Tel： (86) 21-31261976
Fax：(86) 21-31261975
E-mail:[email protected] [email protected]
scan & follow LEEG wechat check website for more info Web：www.leeg.cn

Disclaimer: all the data used in the product description is not legally binding. Relevant technical details may be changed due to further improve

2015.12.V1.0 .9.