Scribd
Upload
402 views2 pages

3.5.5 Packet Tracer - Configure DTP

VLANs 99 and 999 were configured on all switches. Additional VLANs 10, 20, 30 were configured on S2. Pings initially failed between PC1 and PC6 due to ports being in different VLANs 1 and 10. Trunks were configured between S1, S2, S3 with VLAN 1 as the native VLAN, causing a mismatch. The ping failed because S1's VLAN was not set up correctly. The mode on S3's G0/2 port was changed to resolve the trunk negotiation state being shown as off.

Uploaded by

Gillian Balais Doble
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
402 views2 pages

3.5.5 Packet Tracer - Configure DTP

VLANs 99 and 999 were configured on all switches. Additional VLANs 10, 20, 30 were configured on S2. Pings initially failed between PC1 and PC6 due to ports being in different VLANs 1 and 10. Trunks were configured between S1, S2, S3 with VLAN 1 as the native VLAN, causing a mismatch. The ping failed because S1's VLAN was not set up correctly. The mode on S3's G0/2 port was changed to resolve the trunk negotiation state being shown as off.

Uploaded by

Gillian Balais Doble
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

DOBLE, GILLIAN B.

BSIT AI23

3.5.5 Packet Tracer – Configure DTP

Part 1: Verify VLAN configuration.

What VLANs are configured on the switches?


VLANs 99 and 999 are configured on all the switches.

Part 2: Create additional VLANs on S2 and S3.


In addition to the default VLANs, which VLANs are configured on S2?
VLAN 10 (Red), VLAN 20 (Blue), VLAN 30 (Yellow), VLAN 99 (Management) and
VLAN 999 (Native)

Part 3: Assign VLANs to Ports


Now that you have the ports assigned to VLANs, try to ping from PC1 to PC6.

Was the ping successful? Explain.

No, the pings failed because the ports between the switches are in VLAN 1 and
PC1 and PC6 are in VLAN 10.

Part 4: Configure Trunks on S1, S2, and S3.


What will be the result of trunk negotiation between S1 and S2?
Trunk link has been established between S1 and S2

What is the mode and status for this port?


Mode: Auto | Status: trunking

What is the native VLAN for these trunks currently?


VLAN 1

What messages did you receive on S1? How would you correct it?
To correct native VLAN mismatch, configure VLAN 999 as the native VLAN on
S2 and S3.
DOBLE, GILLIAN B.
BSIT AI23

Why was the ping unsuccessful? (Hint: Look at the ‘show vlan brief’ output from
all three switches. Compare the outputs from the ‘show interface trunk’ on all
switches.)
The ping was unsuccessful because the VLAN on S1 was not set up correctly.

Part 5: Reconfigure trunk on S3.


What is the mode and encapsulation on G0/2?
Mode: on | Encapsulation: 802.1q

What is the mode and encapsulation on G0/2 after the change?


Mode: on | Encapsulation: 802.1q

What is the ‘Negotiation of Trunking’ state displayed?


Off

You might also like