0% found this document useful (0 votes)
72 views20 pages3480 E202-00700 Spec. For Communication Equipment
DFAGFDGFD
Uploaded by
Elio DiazCopyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
0% found this document useful (0 votes)
72 views20 pages3480 E202-00700 Spec. For Communication Equipment
DFAGFDGFD
Uploaded by
Elio DiazCopyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
/ 20
EL
SPECIFICATION
FOR
COMMUNICATION EQUIPMENT
ma
sneers vata coven
20 er
ORDER NO, 533260 7; ee
Peace VPM PROJECT/| ~ eos
apenoveo _| fi
: Fe a dae Zt i
na pe bee cine ere
section Ear cove REVISIONS ra
APPROVED customen ma
METORS. A. [se
[CHECKED PROJECT Let
VPM PROJECT ph
‘oRAWN XA (Like or
suena ip og me e902-00700 [" ae
issueo DATE
2A misuassnt WeAVy INDUSTRIES, LYO, MOEE * $6
INDEX
SCOPE
CODES AND STANDARDS
DOCUMENTS
SITE CONDITIONS
PAGING SYSTEM
RADIO SYSTEM
TELEPHONE SYSTEM
PAGE © 96
SCOPE
This specification covers the minimum requirements for
following communication equipment. The equipment shall be
furnished, installed and tested in accordance with this
specification and applicable Standards.
1) Paging system
2) Radio system
3) Telephone system
CODES AND STANDARDS
Communication equipment shall conform to the Standards of the
country of origin.
DOCUMENTS
All documents and drawings shall be written in English and
drawing sizes shall be of A-series, namely AO, Al, A2, A3 and
Ad. The metric system shall be used as the unit of
measurement.
Following documents shall be submitted as a minimum.
- Specification and catalogues
= Outline dimension drawing of equipment with weight
- Terminal board drawing including dimensions of terminals
and location -
- Data sheet(s)
- Surface preparation and painting specification 46
= Schematic diagram of control wiring including terminal
connection diagrams
- Foundation drawings including anchor plan
- Name plate drawing(s)
- Test procedures of witnessed test at shop
- Test reports
- Installation and storage manual
- Maintenance manual
- Parts list
~ Special tool list, if necessary
- Recommended spare parts list
-— Shipping documents
Note) Manuals shall be submitted both in English, and
in Spanish.
SITE CONDITIONS
The electrical equipment and installation shall be suitable
for the environment influences and climatic conditions as
specifie
Altitude 3 At sea level, coastal site
Humidity b Maximum 100% (Design base 79%)
Ambient air temperature: 15°C - 37°C
Atmosphere : Highly corrosive, salty, dusty and
chemical duty area.
Wind speed : Max. annual mean 52 Km/h
Earthquake load : Zone 3 of UBC, 1985 Edition 5.1
PAGING SYSTEM
DESIGN REQUIREMENTS
The paging system shall provide handset station & speaker
paging communications required for the operation of
Methanol plant. Personnel shall be able to access the
paging line from a handset station located in the plant
areas for the communication with another station(s).
Handsets and speakers shall be provided and installed in
plant areas. The speaker amplifiers shall be sized to
provide the sufficient output power to the speaker load
Equipment to be provided shall consist of, but not be
Limited to, the following major items:
- Handset Stations
- Outdoor Speakers
- Mounting Brackets
- Speaker Amplifiers
= Microphones
- Indoor Speakers
- Line Balancer
EQUIPMENT SPECIFICATIONS
General
All materials shall be standard items designed and
constructed for reliable service and rated for continuous
duty. lectronic devices shall be solid-state and
modular. Equipment shall be mounted in enclosures that
shall provide physical protection and electro-magnetic
shielding. 5.2.6
Microphones
Gooseneck type microphones shall be low noise, dynamic
omnidirectional, with a wide frequency response and high
output. Microphones shall be equipped with a desk top
stand and a push-to-talk switch.
Outdoor Speakers
Outdoor speakers shall be reflex horns. The speakers
shall be designed to provide high speech intelligibility
under adverse noise conditions. Construction shall
include weatherproof horns with airtight, weatherproof
and/or explosion proof drivers. The materials and finish
shall provide maximum immunity from wind, rain, humidity
salty air and other destructive elements.
Mounting Brackets
Outdoor speakers shall be provided with a mounting
bracket. ‘The mounting bracket shall permit alignment of
the unit.
Amplifiers
Amplifier shall have a sufficient output power to drive a
speaker. Distortion, input impedance, frequency response
etc. will be manufacturer standard
Handset Stations
Handset stations shall be industrial quality common-
talking stations of a modular design. These stations
shall be housed in a dust-tight enclosures. Explosion~
proof type handset stations shall be provided for
hazardous areas. Indoor type stations shall be provided
in substation(s). oor
5.2.7 ° Indoor Speaker
A horn type indoor speaker shall be provided in
substation(s).
§.2.8 Line Balancer
One unit may be installed in each system, which is :
designed to properly load both “Page and Party Line"
circuits.
5.3 POWER
Primary power source will be'120 VAC 410%, 60 Hz 4108.
5.4 INSTALLATION
Microphone stations will be installed in the control
room,
Loud speakers and handsets shall be installed in the
plant areas and substation(s).
i ~f astesessne
C565 LAYOUT oe
See DWG. 3480 2481-00400.
5.6 QUANTITY
eee will be as per attached paging equipment lis 8
x
6.
6.1
6.2.2
RADIO SYSTEN
DESIGN REQUIREMENTS
The radio system shall consist of portable radios, which
are used for voice communication between Methanol plant
and loading berth.
Equipment to be provided shall consist of the following
items. —.
setae SES eeneaatae we ,
Equipment Z B/Q
ee
- Portable radio with antenna 7 10 SETs
i
- Charger \\ 4 sens
- Rechargeable battery / io sers j
- Carrying case with strap \ a0 sers__/
id
EQUIPMENT SPECIFICATIONS
General
All materials shall be standardized items and be rated
for continuous duty. Electronic devices shall be solid
state and modular.
Equipment shall be housed in enclosures that shall
provide physical protection.
Portable Radio
Portable radio shall be weatherproof and suitable for
hazardous area, It will have the output of 5 watts with
140 MHz to 170 MHz frequency band. Battery unit shall be
easily detachable and replaceable. Portable radio shall
have a synthesizer unit, that is, final frequency
adjustment can be done at site. 6 -
