Engine Rating 1,760 2,100 2,200 2,350 2,600 2,800 2,940
IF05AH-F kW 52 55 55 56 58 59 60
IF05ATH-F kW 74 86 90 95 97 97 98
IF05ATIH-F kW 91 118 122 125 130 131 132
IF05BTIH-F kW - - - - 144 144 144
Although our FM ratings are shown at specific speeds, De Maas FFE engines can be applied at any intermediate speed.
To determine the intermediate speed power; make a linear interpolation from the applicable De Maas power curves.
ENGINE SPECIFICATION IF05AH-F IF05ATH-F IF05ATIH-F IF05BTIH-F
• Engine Series FPT IVECO N45 MNA F40 N45 MNS F40 N45 MNT F41Std N45 MNT F41Plus
• Engine Type 4 Cylinder In-line, 4 cycle, water cooled
• Aspiration Naturally Turbo charged Turbo charged & Intercooled
Aspirated
• Combustion Type Direct injection
• Bore x Stroke mm 104 x 132
• Compression ratio 17.5 : 1
• Displacement litre 4.483
• Rotation Anti-Clockwise
• Weight Approximately kg 600 620
• Valves lashes at cold mm Inlet 0.25 ±0.5
Exhaust 0.50 ±0.5
• Wiring Diagram No. 01.900.07EWEN.03
• Panel Diagram No. 01.900.07PWEN.03
• Oil pan capacity litre High level 9.5
Low level 7.3
• Battery Minimum Capacity recommended Ah 180 (battery not included)
• Cooling capacity litre Please contact FFE Manufacturer
ENGINE RATINGS BASELINES
Engines are not to be used for continuous duty. Engines are to be used only for
stationary emergency standby fire pump service. According to NFPA 25 engines are to
be tested 30 minutes per week at no pump flow and full pump flow once per year.
Power at flywheel according to 97/68 EC, after 50 hours running, 3% tolerance, fuel
Diesel EN 590
Engines rated at standard ISO 3046/1, 25 ° Celsius air temperature, 100 kPa
atmospheric pressure, 30 % relative humidity – Applicable also to DIN 6271, BS 5514,
SAE J1349 Standards.
A deduction of 3 percent from engine horsepower rating at standard SAE conditions
shall be made for diesel engines for each 1,000ft. (305m) altitude above 300ft. (91.4m).
A deduction of 1 percent from engine horsepower rating as corrected to standard SAE
conditions shall be made for diesel engines for every 10⁰F (5.6⁰C) above 77⁰F (25⁰C)
ambient temperature.
Restrictions: Use ratings only for stand-by fire pump applications
IF05-SERIES FM approved POWER CURVES
160
IF05BTIH-F 144 144 144
140
122 125
118 131 132
Power Output (kW)
120 130
IF05ATIH-F
95 97 97 98
100 91 90
IF05ATH-F 86
80 74
58 59 60
IF05AH-F 55 55 56
60 52
Engine Speed (rpm)
40
1600
Copyright 1700
and ownership 1800
of this Power Curve is 1900 2000
vested in De Maas 2100
B.V., whose 2200
prior written consent is2300 2400
required for its 2500or for2600
use, reproduction publication to2700 2800
any third party. 2900
All rights reserved. 3000
Although our FM ratings are shown at specific speeds, FFE engines can be applied at any intermediate speed. To
determine the intermediate speed power; make a linear interpolation from the applicable power curves.
Engine Equipment Standard Optional
Air cleaner Drip proof, disposable Heavy Duty Dry Air Filter Version
Alternator 24 Volts x 90 Amps with belt guard -
Exhaust protection Heat Shield, Elbow Matrass -
Exhaust flex. connection mm (inch) 75 (3”) IF05AH-F Optional
Flywheel housing SAE 3 DRIVE LINE
Flywheel connection SAE 11½ “ with 125 number of teeth STUB SHAFT
Fuel filter Full flow, cartridge type Pre filter with water separator
Fuel Lines by flex. hoses acc. ISO15540 Fix connections for Ø10 Pipes Loose extension lines
Fuel Lift Pump Not included Electrical 24 Volts version
Engine heater 230 Volts 1500 Watt -
Governor speed Constant speed, mechanical -
Mechanical stop lever - Built in fuel pump
Heat Exchanger model 1½ “ IN and 1½ “ OUT (BSP) 20 Bar pressure end-caps (TIH)
Instrument panel Build on Engine -
Junction box Integral with instrument panel -
Lube Oil filter Full flow, cartridge type -
Lube Oil pump Gear type, driven by crankshaft -
Manual start Built on -
Overspeed control Test on instrument panel -
Run-stop control On instrument panel -
Starter motor 24 Volts x 3 kW -
Throttle Control Adjustable speed control Test (low speed) provision with cable
Water pump Centrifugal type driven by gear -
Mountings Pedestal type (Centre Line 400 mm) -
Exhaust system - Complete standard assembly Kits
Cooling Loop Standard ¾ ” Built on Pedestal Diversity of specifications
Sea worthy packing - Crate or case
As part of our policy of on-going improvement resulting from continuing test and development programs, we reserve the right to alter design or specification
without notice. Please check the latest information at to inform yourself of any changes.
Note: All the hereof technical information is, unless stated otherwise, based on the maximum speed of 2,940 rpm
