Type DDSU666.004.

0006Single phase electronic energy meter

(DIN-Rail)
Operation Manual
ZTY0.464.1224

Zhejiang Chint Instrument & Meter Co., Ltd.

May, 2019
 DDSU666.004 .0006type single phase electronic energy meter(DIN-Rail) ZTY0.464.1224
Operation manual Page 1, Total 21

1. Brief Introduction
1.1 Main application & applicable range
Type DDSU666 single phase electronic energy meter (din-rail) (hereinafter referred to as the
“instrument”) is designed based on power monitoring and energy metering demands for electric power
system, communication industry, construction industry, etc. as a new generation of intelligent
instrument combining measurement and communication function, mainly applied into the
measurement and display for the electric parameters in the electric circuit including voltage, current,
power, frequency, power factor, active energy, etc. The network can be realized through RS485
communication interface and external device. Adopting the standard DIN35mm din rail mounting and
modular design, it is characterized with small volume, easy installation and easy networking, widely
applied into the internal energy monitoring and assessment for industrial and mining enterprises, hotels,
schools, large public buildings.
Complied standards:
IEC62052-11 《 Electricity metering equipment(AC)-General requirements, tests and test
conditions- Part11:Metering equipment 》；
IEC62053-21《Electricity metering equipment(AC)-Particularrequirements-Part21: Static meters
for active energy(classes 1 and 2)》；
MODUS-RTU protocol.
1.2 Product Features
1) Metering the positive and negative active power;
2) Adopting wide LCD, it has clear vision.
3) RS485 communication function with communication protocol complied with Modbus-RTU；
4) Adopting DIN35mm standard din rail mounting, structural modular design, it is characterized
with small volume, easy installation and easy networking.
 DDSU666.004.0006 type single phase electronic energy meter(DIN-Rail) ZTY0.464.1036
Operation manual Page 2, Total 21

1.3 Model composition and meanings

Figure 1 Model No. & meanings

1.4 Applicable environmental condition.
Regulated working temperature range: -25℃～+60℃；
Limited working temperature range: -35℃～+70℃；
Relative humidity(Annually average):75％；
Atmospheric pressure:86kPa～106kPa。
2. Working Principle
The working principle block diagram of the instrument is shown in figure 2:

Figure 2 Work principle block diagram

 DDSU666.004.0006 type single phase electronic energy meter(DIN-Rail) ZTY0.464.1036
Operation manual Page 3, Total 21

3. Main Technical Performance & Parameters

3.1 Model specification
Table 1 Model specification
Accuracy Frequency Reference Current Instrument
Model Type
class voltage specification constant
Active 60Hz Direct
DDSU666.004.0004 230 V 5(80)A 800imp/kWh
Class 1 connection
Active Via
DDSU666.004.0004 60Hz 230 V 1.5(6)A 6400imp/kWh
Class1 transformer
Note: Please take the physical sign as standard.
3.2Percentage error
Table 2 Percentage error of single phase energy meter not exceeding the below corresponding
limited value

Percentage error limit of each class

Type Current range Power factor instrument（%）
Class 1
0.01In≤I＜0.05In 1 ±1.5
0.05In≤I≤Imax 1 ±1.0
Via CT
0.02In≤I＜0.1In 0.5L、0.8C ±1.5
0.1In≤I≤Imax 0.5L、0.8C ±1.0
0.05Ib≤I＜0.1Ib 1 ±1.5
Direct 0.1Ib≤I≤Imax 1 ±1.0
connection 0.01Ib≤I＜0.2Ib 0.5L、0.8C ±1.5
0.2Ib≤I≤Imax 0.5L、0.8C ±1.0
In：secondary rated current of CT; Ib：calibrated current of the energy meters;
remark
L:inductive； C：capacitive
3.3 Start
Table 3 Under the referenced voltage and table 4, the energy meter can be started and
continuously measure the energy
 DDSU666.004.0006 type single phase electronic energy meter(DIN-Rail) ZTY0.464.1036
Operation manual Page 4, Total 21

Accuracy class of the energy meter

Instrument Power factor
Class 1
Direct connection 0.004Ib
1
Via transformer 0.002In
3.4 Defluction
The electric energy meter should have good anti-defluction logic. When the voltage loop with
1.15 times of referenced voltage and the current loop is disconnected, the energy will not produce
more than one pulse.
3.5 Electrical parameters
Table 4 Electrical parameters

Specified operating voltage range 0.9Un～1.1Un

Extended operating voltage range 0.8Un～1.15Un
Ultimate operating voltage range 0 Un～1.15Un
Power consumption of the voltage circuit ≤1W/8VA
Power consumption of the current circuit ≤2.5VA
3.6 Other technical parameters
Table 5 Other technical parameters
Measuring range 0～999999.99 kWh（only display 6 bit,，automatic shift of decimal point）
Display mode LCD display
Communication
Modbus-RTU protocol
protocol

3.7 Adoption for key components

Table 6 Adoption for key components
Metering chip SH79F7019
Crystal 32.768kHz
Power transformer ZTY6.170.234
Printed wiring board 1.5（6）A:ZTY8.067.2729V2、ZTY8.067.2731V2、ZTY8.067.2732V2
 DDSU666.004.0006 type single phase electronic energy meter(DIN-Rail) ZTY0.464.1036
Operation manual Page 5, Total 21

5（80）A : ZTY8.067.2729V2、ZTY8.067.2730V2
（Note: the actual plate number is determined according to the actual
sample table）
Current transformer ZTY6.176.301

4. Main functions
4.1 Metering function
1) Accurately metering the positive and negative active power;
2) The storage data of the electric energy meter will not lost after powering off.
4.2 Displayed functions
When the energy meter is in normal working condition (on load state), the positive pulse indicator
should be flashed. If long time for no flashing or light for the indicator, please check whether the
wiring mode of the energy meter is right or not.。

Table 7 LCD logo meanings

Symbol Meaning
V The unit of the voltage, the display data of indicating LCD is
voltage
A The unit of the current, the display data of indicating LCD is
current

W The unit of the active power, the display data of indicating LCD is
active power
var The unit of the reactive power, the display data of indicating LCD
is reactive power
 DDSU666.004.0006 type single phase electronic energy meter(DIN-Rail) ZTY0.464.1036
Operation manual Page 6, Total 21

Hz The unit of the frequency, the display data of indicating LCD is

frequency
kWh The unit of the active energy, the display data of indicating LCD is
active energy
The display time of the measurement data is five seconds and information sample for every page
of the measured information of measurement data (if not consistent with the instrument panel, please
take the object as standard.)
Light time of the background: 1 min.
Table 8 Display Instruction
Content Instruction
Means the current display
voltage is U, the unit is “V”,
the left picture is
U=220.0V。

Means the current display

current is I, the unit is “A”,
the left picture is I=5.000A.

Means the current display is

the active power P，the unit
is “kW”，the left picture is
P=1.100kW.
Means the current display is
the power factor Ft， the left
picture is Ft=1.000.
Means the current display is
frequency F, the left picture
is F=50.00Hz.
DDSU666.004.0006 type single phase electronic energy meter(DIN-Rail) ZTY0.464.1036
Operation manual Page 7, Total 21

Means the current positive

active energy EImp, the unit
is “kWh”, the left picture is
EImp=1.20kWh.
Means the current negative
active energy EExp, the unit
is “kWh”, the left picture is
EExp=1.00kWh.
Means the current
combination active energy
total ComEp, the unit is
“kWh”, the left picture is
ComEp=2.20kWh.

Means the current

communication protocol is
Modbus.
Represents 8 data bits, no
effect bit and one stop bit of
the current communication
protocol.

Means the current

communication address is
11.

Means the current

communication baud rate is
9600.
 DDSU666.004.0006 type single phase electronic energy meter(DIN-Rail) ZTY0.464.1036
Operation manual Page 8, Total 21

Keyboard operation: After pressing the button for a long time, the display interface
enters the switching interface of setting 645 protocol and Modbus protocol. Shortly
press can switch the protocol, not the address page (only the ModBus protocol can be
switched to the address page), the address of ModBus can be set by the button, the button
can set the address range 1-99.

Figure 3 Long press button

4.3 Communication function
The instrument adopts RS485 communication mode with baud rate to be set as 1200, 2400bps,
4800bps and 9600bps.
For a same communication circuit, it can at most be connected with thirty-two instruments at the
same time, with each instrument to be set as their communication address. For the communication
connection, it should use shielded twisted pair with copper mesh with wire diameter not below

0.5mm2 . On wiring arrangement, the communication line shall be away from strong cable or other

strong electric field with the maximum transmission distance to be 1200m. For the typical networking
connection mode, please see the below figure, users can select other suitable connection mode based
on detailed conditions.
 DDSU666.004.0006 type single phase electronic energy meter(DIN-Rail) ZTY0.464.1036
Operation manual Page 9, Total 21

Figure 4 Schematic diagram of communication connection

When the instrument is set to be ModBus-RTU transmission mode, ModBus-RTU communication
protocol adopts host-slave response in one communication line. Firstly, the host computer’s signal will
seek for a terminal device (slave) with only one address, then the terminal device will produce
response signal and transmit to the host computer in opposite direction, that is, half duplex working
mode. This protocal only allows communication between the host (PC, PLC, etc.) and the terminal
device, rather than data exchanges between the independent terminal devices. Thus, each terminal
device will not occupy the communication circuits in their initialization, and only be limited to
response the query signal to the host computer.
The instrument can provide ModBus-RTU communication protocol (see appendix A), for the
parameter information to be read or modified by the communication, please see the below table.
Table 9 Communication parameter information

Length
Parameter Read&write
Parameter code Instruction of the parameters Type of data of data
address attributes
Word
16-bit with
0000H UCode Programming password codE 1 R/W
symbols
Reserved, actual read is the 16-bit with
0001H REV. 1 R
version number symbols
Electric energy zero clearing 16-bit with
0002H ClrE 1 R/W
CLr.E(1:zero clearing) symbols
DDSU666.004.0006 type single phase electronic energy meter(DIN-Rail) ZTY0.464.1036
Operation manual Page 10, Total 21

16-bit with
0003H RESERVED RESERVED 1
symbols
16-bit with
0004H RESERVED RESERVED 1
symbols
16-bit with
0005H ChangeProtocol Protocol changing-over 1 R/W
symbols
16-bit with
0006H Addr Communication address Addr 1 R/W
symbols
16-bit with
0007H RESERVED 1
Urat symbols

16-bit with
0008H RESERVED 1
Irat symbols
16-bit with
0009H RESERVED RESERVED 1
symbols
16-bit with
000AH RESERVED RESERVED 1
symbols
16-bit with
000BH RESERVED RESERVED 1
symbols
Communication baud rate 16-bit with
000CH BAud 1 R/W
bAud symbols
16-bit with
000DH RESERVED RESERVED 1
symbols
16-bit with
000EH RESERVED RESERVED 1
symbols

16-bit with
000FH RESERVED RESERVED 1
symbols
16-bit with
0010H RESERVED RESERVED 1
symbols
 DDSU666.004.0006 type single phase electronic energy meter(DIN-Rail) ZTY0.464.1036
Operation manual Page 11, Total 21

Electric quantity of the secondary side

single precision
2000H U Voltage 2 R
floating decimal
single precision
2002H I Current 2 R
floating decimal

Conjunction active power，the single precision

2004H P 2 R
unit is KW floating decimal

Conjunction reactive power， single precision

2006H Q 2 R
the unit is Kvar floating decimal

single precision
2008H RESERVED RESERVED 2 R
floating decimal
single precision
200AH PF Conjunction power factor 2 R
floating decimal
single precision
200CH RESERVED RESERVED 2 R
floating decimal
single precision
200EH Freq Frequency 2 R
floating decimal
single precision
2010H RESERVED RESERVED 2 R
floating decimal
Electrical data of the secondary side
single precision
4000H Ep Active in electricity 2 R
floating decimal

ChangeProtocol such as protocol switching, data for 2 for Modbus RTU protocol -, data to 1 for DL/T
645-2007；
The CLr. E power reset write 1 removal of total power；
BAud rate: 1:2400bps; 2:4800bps; 3:9600bps；；
4.4 Outline &Mounting Dimension
Outline dimension: 36mm×98mm×65mm；
 DDSU666.004.0006 type single phase electronic energy meter(DIN-Rail) ZTY0.464.1036
Operation manual Page 12, Total 21

Din rail mounting dimension: 35mm, with configuration to be shown as figure 4:

Figure 5 Configuration
6. Installation & Operation Instruction
6.1 Inspection
1) Before installation, firstly check whether the model No. and specification of the product on the
package is the same as the object. If not, please contact the supplier.
2) Check whether the product shell in the carton is damaged, if is, please contact the supplier.
6.2 Installation
Directly clip the instrument on the rail and install it on the distribution box.
1）When installing, firstly clip one terminal of the slot and then clip to the rail with power.
2）When disassembling, press the movable card with a screwdriver and take out the instrument.
6.3 Wiring mode
6.3.1 Instruction of wiring terminal
Before powering, you must check whether the wiring mode of the instrument is correct, and the
wiring diagram is shown as below:
 DDSU666.004.0006 type single phase electronic energy meter(DIN-Rail) ZTY0.464.1036
Operation manual Page 13, Total 21

Figure 6 Direct connection

Figure 7 Via transformer

7. Diagnosis, analysis and elimination of common faults
Fault Analysis of causes Troubleshooting Remark
phenomenon
Display fault The wiring may not Check if the actual connection is While checking
connected the same as the requirement of the the
according to the wiring diagram. Pay special connection, be
wiring diagram of attention to “N” position of the sure the meter
the meter voltage, the high&low end of the is in the state
current and terminal labeling are of
different from actual number. disconnection,
guarantee the
 DDSU666.004.0006 type single phase electronic energy meter(DIN-Rail) ZTY0.464.1036
Operation manual Page 14, Total 21

safety of human
life.

Communication The communication Check if the communication setting

fault setting information such as communication
information of the address, baud rate, verification
meter may be mode is the same as the PC settings.
incorrect
If the above method cannot eliminate the fault, please contact with the after-sale service of digital
meter from Zhejiang CHINT Instrument Co., Ltd.
8. Transportation & Storage
The package of the instrument shall adopt materials complied with environmental protection, under
package condition, the instrument and accessories shall be stored in the dry and ventilated places, to
avoid humidity and corrosive gas erosion, with the limited environmental temperature for storage to be
-40℃～+70℃ and relative humidity not exceeding 75%.
The package of the instrument shall comply with the provisions of GB/T 13384-2008 of General
specifications for packings of mechanical and electrical products with the environmental temperature
requirement and transportation for the normal storage complied with the provisions of GB/T
25480-2010 of Basic environmental conditions and testing methods for instruments transportation and
storage
Complete set of package for single product, including:
1) One set of instrument
2) One operation manual
3) One bag of desiccant
4) Certificate
10. Maintenance & Service
We guarantee free reparation and change for the multi-meter if found any unconformity with the standard, under

circumstance of that the users fully comply with this instructions and complete seal after delivery within 18 months.
 DDSU666.004.0006 type single phase electronic energy meter(DIN-Rail) ZTY0.464.1036
Operation manual Page 15, Total 21

Appendix A: MODBUS-RTU Communication Protocol

A.1 Communication format
Information transmission adopts asynchronous mode, taking byte as the unit. The communication date
transmitted between the host and slave computer is the format of 10-digit characters, including one
start bit(0), 8 data bits without check bit, two stop bits(1)(other format can be customized).
Format of information frame:
Table A.1

Function CRC check

Start Address code Data field End
code code
More than More than
1 n
3.5-character 1 character 2 characters 3.5-character
character characters
dead time dead time
 DDSU666.004.0006 type single phase electronic energy meter(DIN-Rail) ZTY0.464.1036
Operation manual Page 16, Total 21

A.2 Communication information transmitting procedure

When communication command is transmitted from the host computer to the slave computer, the slave
computer which matches the address code sent by the host computer receives the communication
command. If CRC checks without any fault, then the corresponding operation will be carried out, after
that the implement result (date) is returned to the host computer. The returned information contains
address code, function code, implement date and CRC check code.
A.2.1 Address code
Address code is the first byte of each communication frame, with the range from 1 to 247. Each slave
must have an exclusive address code in the bus, only the slave computer which matches the address
code sent by the host computer can respond returned information. When the slave computer returns the
information, the returned data will begin with their respective address codes. The address code sent
from the host computer indicates the slave address, the returned address code from the slave computer
indicates the slave address, while the corresponding address code indicates where the information
comes from.
A.2.2 Function code
It’s the second byte of each communication frame. It’s sent by the host and tells the slave computer
what actions should be carried out through function code. The slave will respond, and the functional
code is the same as that sent by the host computer, which indicates that the slave computer has
responded the host and complemented the relative operation.
The instrument supports the following two function codes:
Table A.2

Function
Definition Operation
code
03H Read register Read one or several register data
Write multichannel
10H Write n 16-bit binary data into n continuous registers
register
A.2.3 Data area
The data field will be different based on different function codes. These data can be numerical
 DDSU666.004.0006 type single phase electronic energy meter(DIN-Rail) ZTY0.464.1036
Operation manual Page 17, Total 21

values, reference addresses and so on. For different slave computers, both the address and data
information are different, and the communication information table should be provided.
The host utilizes communicate command (function code 03H and 10H) to read and modify the
data registers of the slave freely. But the data length which is read or write at one time should not be
out of the effective range of the data register’s address.
A.3 Brief introduction of function code
A.3.1 Function code 03H：Read register
For example: The slave address which the host intends to read is 01H, the start register address is two
register data of 0CH, sent by the host:
Table A.3
The host sends Send message
Address code 01H
Function code 03H
High byte 00H
Start register address
low byte 0CH
High byte 00H
Register number
low byte 02H
low byte 04H
CRC 校验码
High byte 08H
If the data of the slave register 0CH, 0DH is 0000H, 1388H, the slave will return:
Table A.4
The slave returns Return message
Address code 01H

Function code 03H

Bytes 04H
High byte 00H
Register 0CH data
low byte 00H
Register 0DH data High byte 13H
 DDSU666.004.0006 type single phase electronic energy meter(DIN-Rail) ZTY0.464.1036
Operation manual Page 18, Total 21

low byte 88H

low byte F7H
CRC check code
High byte 65H

A.3.2 Function code 10H：Write multi-port register

For example：The host intends to save data of 0002H, 1388H, 000AH into the slave address of
01H，the start register address is the three registers of 00H, sent by the host:
Sent by the host:
Table A.5
The host sends Send message

Address code 01H

Function code 10H
High byte 00H
Start register address
low byte 00H
High byte 00H
Register number
low byte 03H
Write bytes 06H

The data to be written in High byte 00H

00H register low byte 02H

The data to be written in High byte 13H

01H register low byte 88H

The data to be written in High byte 00H

02H register low byte 0AH

low byte 9BH

CRC check code
High byte E9H
Returned by the slave
Table A.6
The slave returns Return message
Address code 01H
 DDSU666.004.0006 type single phase electronic energy meter(DIN-Rail) ZTY0.464.1036
Operation manual Page 19, Total 21

Function code 10H

High byte 00H
Start register address
low byte 00H
High byte 00H
Register number
low byte 03H

low byte 80H

CRC check code
High byte 08H
A.4 16-digit CRC check code
The host or slave computer can be judged by the check code to see if the received information is
correct or not. The interruption by electronic noises or other factors may cause errors during
information transmission.
16-digit CRC check code is calculated by the host, located at the end of the transmit information
frame. The slave recalculates the received information of CRC and compares if the calculated CRC
goes in line with the received CRC, if not, there is an error. Only 8 data bits are used during CRC
calculation, both the start bits and the stop bits are not involved in the calculation.
The calculation method of CRC check code is stated as follows：
1) Pre-arrange one 16-digit register as a hexadecimal FFFF ( i.e. fully 1), the register is called
CRC register;
2) Make the first 8-digit binary data ( the first byte of the communication information frame) with
the lower 8 digits of the 16-digit CRC register by XOR calculation, the result is placed in CRC
register;
3) Shift the content of CRC register rightward by one digit (towards the lower digit) and fill in the
highest digit with 0, check the shift-out digit after rightward shifting;
4) If the shift-out digit is 0: repeat step 3) (shift rightward one digit again);
If the shift-out digit is 1: make CRC register with multinomial A001 by XOR calculation
5) Repeat step 3) and 4) until shift rightward for 8 times, then all the 8 digits are processed;
6) Repeat step 2) and 5), process the next byte of the communication information frame;
7) After calculating all the bytes of the communication information frame (exclude CRC check
 DDSU666.004.0006 type single phase electronic energy meter(DIN-Rail) ZTY0.464.1036
Operation manual Page 20, Total 21

code) according to the above steps, the content of the CRC register to be get is: 16-digit CRC check
code.
A.5 Error handling
When the meter detects other errors except the error of CRC check code, the information will be
returned to the host, the highest digit of the function code is 1, i.e. the function code returned to the
host from the slave is adding 128 base on the function code sent from the host. The error returned from
the slave is as follows:
Table A.7
Address Function code（top CRC check code CRC check code
Error code
code digit is 1） low byte High byte
1 byte 1 byte 1 byte 1 byte 1 byte

Error code is as follows：

Table A.8
01H Illegal function code The function code received is not supported by the instrument
Illegal register The register address received is out of the register address range
02H
address
Illegal data value The data value received is out of the corresponding address data
03H
range
 DDSU666.004.0006 type single phase electronic energy meter(DIN-Rail) ZTY0.464.1036
Operation manual Page 21, Total 21

Dear clients,

Please assist us: when the product life is end, to protect our environment, please recycle the product or

components, while for the materials that cannot be recycled, please also deal with it in a proper way. Really

appreciate your cooperation and support.

Name of Company: Zhejiang Chint Instrument & Meter Co., Ltd.

Address: Wenzhou Bridge Industrial Zone, Yueqing, Zhejiang, China.

Zip Code：325603

Telephone：0577-62877777

Fax：0577-62891577

Technical hotline：0577-62919999

Fake Complaint： 0577-62789987

Website: http: //www.chint.com

Email：ztyb＠chint.com
Date of Issue: May, 2019.
No.: ZTY0.464.1224V1