SA-WMSP76

SERVICE MANUAL US Model

Canadian Model
Ver 1.1 2004.07
AEP Model
UK Model
E Model
Australian Model

• SA-WMSP76 is the sub woofer section in

HT-DDW755/760 and HT-4800DP.

SPECIFICATIONS
Speaker system Active subwoofer,
magnetically shielded
Speaker unit 200 mm cone type
Enclosure type Acoustically loaded bass
reflex
RMS output: 100 W (6 ohms, 100 Hz,
THD 10%)
Input LINE IN (input pin jacks)

Power requirements
Area code Power requirements
US, CA 120 V AC, 60 Hz
CEL, CEK, MY, SP, AU 230 V AC, 50/60 Hz

Power consumption 75 W
Dimensions (w/h/d) (Approx.)
270 × 325 × 398 mm
(10 3/4 × 12 7/8 × 15 3/4
inches) including front
panel
Mass (Approx.) 9.0 kg (19 lb 14oz)

• Abbreviation
AU : Australian model
CA : Canadian model
CEK : UK model
CEL : AEP model
MY : Malaysia model
SP : Singapore model

ACTIVE SUBWOOFER
9-877-667-02 Sony Corporation
2004G16-1 Home Audio Company
© 2004.07 Published by Sony Engineering Corporation
SA-WMSP76

SAFETY CHECK-OUT Unleaded solder

After correcting the original service problem, perform the Boards requiring use of unleaded solder are printed with the lead-
following safety checks before releasing the set to the customer: free mark (LF) indicating the solder contains no lead.
Check the antenna terminals, metal trim, “metallized” knobs, screws, (Caution: Some printed circuit boards may not come printed with
and all other exposed metal parts for AC leakage. Check leakage as the lead free mark due to their particular size.)
described below.
: LEAD FREE MARK
LEAKAGE Unleaded solder has the following characteristics.
The AC leakage from any exposed metal part to earth ground and • Unleaded solder melts at a temperature about 40°C higher than
from all exposed metal parts to any exposed metal part having a ordinary solder.
return to chassis, must not exceed 0.5 mA (500 microamperes). Ordinary soldering irons can be used but the iron tip has to be
Leakage current can be measured by any one of three methods. applied to the solder joint for a slightly longer time.
1. A commercial leakage tester, such as the Simpson 229 or RCA Soldering irons using a temperature regulator should be set to
WT-540A. Follow the manufacturers’ instructions to use these about 350°C.
instruments. Caution: The printed pattern (copper foil) may peel away if the
2. A battery-operated AC milliammeter. The Data Precision 245 heated tip is applied for too long, so be careful!
digital multimeter is suitable for this job. • Strong viscosity
3. Measuring the voltage drop across a resistor by means of a Unleaded solder is more viscous (sticky, less prone to flow)
VOM or battery-operated AC voltmeter. The “limit” indication than ordinary solder so use caution not to let solder bridges
is 0.75 V, so analog meters must have an accurate low-voltage occur such as on IC pins, etc.
scale. The Simpson 250 and Sanwa SH-63Trd are examples of • Usable with ordinary solder
a passive VOM that is suitable. Nearly all battery operated It is best to use only unleaded solder but unleaded solder may
digital multimeters that have a 2V AC range are suitable. (See also be added to ordinary solder.
Fig. A)

To Exposed Metal
Parts on Set

AC
0.15µF voltmeter
1.5kΩ
(0.75V)

Earth Ground

Fig. A. Using an AC voltmeter to check AC leakage.

SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
PUBLISHED BY SONY. DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

2
 SA-WMSP76
SECTION 1
DIAGRAMS
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. • IC BLOCK DIAGRAMS
(In addition to this, the necessary note is printed in each block.)
IC301-STK404-100S (MAIN Board)
Note on Printed Wiring Boards: Note on Schematic Diagram:
• X : parts extracted from the component side. • All capacitors are in µF unless otherwise noted. p: µµF 50 WV
• Y : parts extracted from the conductor side. or less are not indicated except for electrolytics and tantalums.
• a : Through hole • 2 : nonflammable resistor.
• : Pattern from the side which enables seeing. • 5 : fusible resistor.
• All resistors are in Ω and 1/4 W or less unless otherwise speci-
Caution: fied.
Pattern face side: Parts on the pattern face side seen from • C : panel designation.
(Side B) the pattern face are indicated.
Parts face side: Parts on the parts face side seen from The components identified by Les composants identifiés par
mark 0 or dotted line with mark une marque 0 sont critiques
(Side A) the parts face are indicated. 0 are critical for safety. pour la sécurité.
Replace only with part number Ne les remplacer que par une
specified. pièce portant le numéro spécifié.
• Indication of transistor
• A : B+ Line.
• B : B– Line.
B C E • Voltages are dc with respect to ground under no-signal condi-
These are omitted. tions.
no mark : Power on
• Voltages are taken with a VOM (Input impedance 10MΩ).
Voltage variations may be noted due to normal preduction tol-
erances. SUB
1 2 3 4 5 6 7 8 9 10 11 12
• Signal path.
F : AUDIO
• Abbreviation
CND : Canadian model.

1-1. CIRCUIT BOARD LOCATION

INPUT(CONTROL) BOARD

MAIN BOARD

SWITCH BOARD

POWER TRANS BOARD

CONTROL BOARD

3 3
SA-WMSP76
1-2. PRINTED WIRING BOARD – MAIN SECTION – • See page 3 for Circuit Board Location • : Uses unleaded solder.

1 2 3 4 5 6 7 8

4 5 ( )

IC203
B 1 8

(Page 5)

4 5

IC202
1 8

(US,CND)

INPUT
(Page 5)

IC301
D
• Semiconductor
Location
Ref. No. Location
D205 C-3
D206 C-3
D301 E-4
E SP1
D302
D304
E-4
D-2
D401 F-2
D501 E-2
D502 E-4
D602 C-2

IC202 C-3
IC203 B-3
IC301 D-4
3

F Q501
Q502
D-2
D-2
Q503 D-2
POWER TRANS
Q504 D-2
Q505 E-4
1-686-985-
(Page 5)

11

(11)

4 4
 SA-WMSP76
1-3. PRINTED WIRING BOARD – POWER SECTION – • See page 3 for Circuit Board Location • : Uses unleaded solder.

1 2 3 4 5 6 7 8

A
AC
IN

(Page 4)

(Page 4)

(Page 4)

5 5
SA-WMSP76
1-4. SCHEMATIC DIAGRAMS

R209
100k
∗3 C209
R208 US, CND : 220p
10k EXCEPT US, CND : 100p
IC202(1/2)
M5218AP_22 C801
R212 R213 IC203(1/2) CNP801 10
C201 22k 22k M5218AP_22 CNP111
CN202 R216 3P 50
10 2P 10k 3P RV801
50V C203 C204
J101 20k
0.1 0.1
C208
R202 0.22
C101 R110 1k IC202(2/2)
R210
220p 100k CN101 R207 470k M5218AP_22
10k
2P C210

R206
R205
R214 C207 C209

RD12ESB2
100k

10k
10 50V
220k 0.01
∗3

D205
C205
R211 10
220k 50V IC203(2/2)
M5218AP_22

C206
10
50V

D206
RD12ESB2
R217 C211
100k 220p

R506
R301
22k 4.7k

Q505
2SC2785-HFE
C302 C313
10 50V 220p
C312 R306
R308
R507 ∗1 4.7k
R307
C308
R313 10
4.7k R303 R304 4.7k
1SS133T-77

10K C301 R302 50V

1SS133T-77

220p 47k 470 100

∗1
D302

2W
D301
1SS133T-77

50V
C312
D502

R309 US, CND : 220p C305

220 EXCEPT US, CND : 1000p 100
R315

50V
47k

C304 C307
C303 100 47
JW501
100
10V
50V 50V
C306 ∗2 C310
10
50V
US, CND : 0.1
EXCEPT US, CND : 220p
∗4
US, CND
D602 R311
CN204 1SS133T-77 C309 680 1W T L
2P C311 0.1
10p 50V

1SS133T-77

RY301
R601 R312
C310

D304
2.2K 22k
C601
10 R314
R305
47k
∗2
50V R508 1
1k 1/4W
R310
10

CN3
CN2
F901 2P
∗4 2P
D401
R401 C901
Q502 D3SBA20 JW1 S901
R503 R502 1k JW401 4700p
2SC2784-F CN301 250V
100k 47k C401
Q504 R504 0.1 2P
100k
DTC124ESA C403
C405 C2
3300 4700p
100
50V 250V
25V CN1
2P
D901
C406 LNJ301MPUJAB
C502 C404
220 100 R402 3300 C402
R505
35V 25V 1k 2W 0.1
22k JW402 50V CN402 CNP401
3P 3P CN901
Q503
2SC2785-HFE Q501
2SC2785-HFE

D501 R501 R500

1SS133T-77 10k 2.2k T1
C503
C501
220 10V 10
50V

6 6
 SA-WMSP76
SECTION 2
EXPLODED VIEWS
NOTE:
• -XX, -X mean standardized parts, so they may • Abbreviation
have some differences from the original one. AUS :Australian model The components identified by mark 0 or
• Items marked “*” are not stocked since they CND :Canadian model dotted line with mark 0 are critical for
are seldom required for routine service. Some MY :Malaysia model safety.
delay should be anticipated when ordering SP :Singapore model Replace only with part number specified.
these items.
• The mechanical parts with no reference num- Les composants identifiés par une marque
ber in the exploded views are not supplied. 0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.

2-1. FRONT SECTION

SP1

not
supplied
8

4
#1
2
#1

not Amp section

#1
supplied

#1 not
supplied
supplied
with RV801

1 3

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
1 4-243-842-21 GRILLE FRAME 6 4-999-482-71 KNOB (VOL)
2 4-998-417-02 EMBLEM (NO.5), SONY 8 4-235-677-01 SCREW (4X20) (TYPE1), +BVTP
3 4-243-834-01 FRONT PANEL (US, CND) SP1 1-529-995-13 SPEAKER (20cm) (US, CND)
3 4-243-834-21 FRONT PANEL (EXCEPT US, CND) SP1 1-825-004-13 SPEAKER (20cm) (EXCEPT US, CND)
4 4-973-938-83 KNOB (A), PUSH #1 7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3

7
SA-WMSP76

2-2. AMP SECTION

55 52 not #1
supplied 57
#1
#3

not
supplied #1
not not
supplied supplied
51
T1 #3 not 53
supplied

F901
#3 not
supplied

54

53

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
51 A-4723-991-A SPEAKER CABINET ASSY 0 57 1-783-820-11 CORD, POWER (US, CND)
(US, CND, MY, SP, AUS) 0 F901 1-532-463-51 FUSE (T1AL/250V) (EXCEPT US, CND)
51 A-4723-998-A SPEAKER CABINET ASSY (UK, AEP) 0 F901 1-533-450-12 FUSE, GLASS TUBE (DIA. 5) (T2.5AL/125V)
52 A-4731-189-A MAIN BOARD, COMPLETE (US, CND) (US, CND)
52 A-4753-485-A MAIN BOARD, COMPLETE (EXCEPT US, CND) 0 T1 1-439-627-11 TRANSFORMER, POWER (EXCEPT US, CND)
53 4-235-677-01 SCREW (4X20) (TYPE1), +BVTP 0 T1 1-439-628-11 TRANSFORMER, POWER (US, CND)

* 54 3-703-244-00 BUSHING (2104), CORD #1 7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3
55 3-905-609-31 SCREW (TRANSISTOR) #3 7-685-881-09 SCREW +BVTT 4X8 (S)
0 57 1-696-847-22 CORD, POWER (AUS)
0 57 1-769-744-11 CORD, POWER (UK, AEP, MY, SP)

The components identified by mark 0 or Les composants identifiés par une marque
dotted line with mark 0 are critical for 0 sont critiques pour la sécurité.
safety. Ne les remplacer que par une pièce portant
Replace only with part number specified. le numéro spécifié.

8
 SA-WMSP76
SECTION 3 CONTROL
ELECTRICAL PARTS LIST INPUT(CONTROL) MAIN
NOTE:
• Due to standardization, replacements in the • RESISTORS When indicating parts by reference num-
parts list may be different from the parts All resistors are in ohms. ber, please include the board name.
specified in the diagrams or the components METAL: metal-film resistor
used on the set. METAL OXIDE: Metal Oxide-film resistor The components identified by mark 0 or
• -XX, -X mean standardized parts, so they F: nonflammable dotted line with mark 0 are critical for
may have some difference from the origi- • SEMICONDUCTORS safety.
nal one. In each case, u: µ, for example: Replace only with part number specified.
• Items marked “*” are not stocked since they uA...: µA... , uPA... , µPA... ,
are seldom required for routine service. uPB... , µPB... , uPC... , µPC... , Les composants identifiés par une marque
Some delay should be anticipated when or- uPD..., µPD... 0 sont critiques pour la sécurité.
dering these items. • Abbreviation Ne les remplacer que par une pièce portant
• CAPACITORS: AUS :Australian model le numéro spécifié.
uF: µF CND :Canadian model
• COILS MY :Malaysia model
uH: µH SP :Singapore model

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
CONTROL BOARD, COMPLETE C209 1-128-809-11 CERAMIC 100PF 5% 50V
************************ (EXCEPT US, CND)
C209 1-128-813-11 CERAMIC 220PF 5% 50V
< CAPACITOR > (US, CND)
C210 1-126-964-11 ELECT 10uF 20% 50V
C801 1-126-964-11 ELECT 10uF 20% 50V C211 1-128-813-11 CERAMIC 220PF 5% 50V

< CONNECTOR > C301 1-128-813-11 CERAMIC 220PF 5% 50V

C302 1-126-964-11 ELECT 10uF 20% 50V
CNP801 1-691-765-11 PLUG (MICRO CONNECTOR) 3P C303 1-104-658-91 ELECT 100uF 20% 10V
C304 1-126-968-11 ELECT 100uF 20% 50V
< VARIABLE RESISTOR > C305 1-126-968-11 ELECT 100uF 20% 50V

RV801 1-227-511-11 CARBON, VARIABLE RESISTOR 20K (LEVEL) C306 1-126-964-11 ELECT 10uF 20% 50V
************************************************************ C307 1-126-967-11 ELECT 47uF 20% 50V
C308 1-126-964-11 ELECT 10uF 20% 50V
INPUT (CONTROL) BOARD, COMPLETE C309 1-136-165-00 FILM 0.1uF 5% 50V
******************************* (US, CND)
C310 1-128-813-11 CERAMIC 220PF 5% 50V
< CAPACITOR > (EXCEPT US, CND)

C101 1-128-813-11 CERAMIC 220PF 5% 50V C310 1-136-165-00 FILM 0.1uF 5% 50V
C201 1-126-964-11 ELECT 10uF 20% 50V (US, CND)
C311 1-162-199-31 CERAMIC 10PF 5% 50V
< CONNECTOR > C312 1-128-813-11 CERAMIC 220PF 5% 50V
(US, CND)
* CN101 1-506-944-11 PIN, CONNECTOR 2P C312 1-128-821-11 CERAMIC 1000PF 5% 50V
(EXCEPT US, CND)
< JACK > C313 1-128-813-11 CERAMIC 220PF 5% 50V

J101 1-815-025-11 JACK, PIN 1P (INPUT) C314 1-128-813-11 CERAMIC 220PF 5% 50V
(EXCEPT US, CND)
< RESISTOR > C315 1-127-876-11 CERAMIC 0.01uF 10% 50V
(EXCEPT US, CND)
R110 1-247-879-91 CARBON 100K 5% 1/4W C316 1-127-876-11 CERAMIC 0.01uF 10% 50V
R202 1-247-831-91 CARBON 1K 5% 1/4W (EXCEPT US, CND)
************************************************************ C317 1-127-876-11 CERAMIC 0.01uF 10% 50V
(EXCEPT US, CND)
A-4731-189-A MAIN BOARD, COMPLETE (US, CND) C318 1-128-813-11 CERAMIC 220PF 5% 50V
A-4753-485-A MAIN BOARD, COMPLETE (EXCEPT US, CND) (EXCEPT US, CND)
*********************
C401 1-136-165-00 FILM 0.1uF 5% 50V
< CAPACITOR > C402 1-136-165-00 FILM 0.1uF 5% 50V
C403 1-126-974-11 ELECT 3300uF 20% 50V
C203 1-136-165-00 FILM 0.1uF 5% 50V C404 1-126-974-11 ELECT 3300uF 20% 50V
C204 1-136-165-00 FILM 0.1uF 5% 50V C405 1-104-665-11 ELECT 100uF 20% 25V
C205 1-126-964-11 ELECT 10uF 20% 50V
C206 1-126-964-11 ELECT 10uF 20% 50V C406 1-104-665-11 ELECT 100uF 20% 25V
C207 1-131-679-31 FILM 0.01uF 5% 50V C501 1-126-964-11 ELECT 10uF 20% 50V
C502 1-126-949-11 ELECT 220uF 20% 35V
C208 1-131-696-11 FILM 0.22uF 5% 50V C503 1-126-923-91 ELECT 220uF 20% 10V

9
SA-WMSP76

MAIN POWER TRANS SWITCH

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
C601 1-126-964-11 ELECT 10uF 20% 50V R304 1-215-886-11 METAL OXIDE 100 5% 2W
R305 1-247-871-91 CARBON 47K 5% 1/4W
< CONNECTOR > R306 1-247-847-91 CARBON 4.7K 5% 1/4W
R307 1-247-847-91 CARBON 4.7K 5% 1/4W
* CN202 1-506-944-11 PIN, CONNECTOR 2P 0 R308 1-234-182-11 ENCAPSULATED COMPONENT
CN204 1-564-505-11 PLUG, CONNECTOR 2P
CN301 1-564-320-00 PIN, CONNECTOR (3.96mm PITCH) 2P R309 1-249-409-11 CARBON 220 5% 1/4W
CN402 1-785-101-11 PIN, CONNECTOR (3.96mm PITCH) 3P R310 1-249-393-11 CARBON 10 5% 1/4W
R311 1-215-868-00 METAL OXIDE 680 5% 1W
< CONNECTOR > R312 1-247-863-91 CARBON 22K 5% 1/4W
R313 1-249-429-11 CARBON 10K 5% 1/4W
CNP111 1-691-765-11 PLUG (MICRO CONNECTOR) 3P
0 R314 1-217-637-00 FUSIBLE 1 5% 1/4W
< DIODE > R315 1-247-871-91 CARBON 47K 5% 1/4W
R317 1-249-393-11 CARBON 10 5% 1/4W
D205 8-719-110-31 DIODE RD12ESB2 (EXCEPT US, CND)
D206 8-719-110-31 DIODE RD12ESB2 R401 1-215-892-11 METAL OXIDE 1K 5% 2W
D301 8-719-991-33 DIODE 1SS133T-77 R402 1-215-892-11 METAL OXIDE 1K 5% 2W
D302 8-719-991-33 DIODE 1SS133T-77
D304 8-719-991-33 DIODE 1SS133T-77 R500 1-249-421-11 CARBON 2.2K 5% 1/4W
R501 1-249-429-11 CARBON 10K 5% 1/4W
D401 8-719-500-56 DIODE D3SBA20 R502 1-247-871-91 CARBON 47K 5% 1/4W
D501 8-719-991-33 DIODE 1SS133T-77 R503 1-247-879-91 CARBON 100K 5% 1/4W
D502 8-719-991-33 DIODE 1SS133T-77 R504 1-247-879-91 CARBON 100K 5% 1/4W
D602 8-719-991-33 DIODE 1SS133T-77
R505 1-247-863-91 CARBON 22K 5% 1/4W
< GROUND TERMINAL > R506 1-247-863-91 CARBON 22K 5% 1/4W
R507 1-247-847-91 CARBON 4.7K 5% 1/4W
G1 1-537-738-21 TERMINAL, GROUND R508 1-247-831-91 CARBON 1K 5% 1/4W
G2 1-537-738-21 TERMINAL, GROUND R601 1-215-894-11 METAL OXIDE 2.2K 5% 2W

< IC > < RELAY >

IC202 8-759-636-74 IC M5218AP-22 RY301 1-515-920-11 RELAY (24V)

IC203 8-759-636-74 IC M5218AP-22 ************************************************************
IC301 6-600-181-01 IC STK404-100S
POWER TRANS BOARD, COMPLETE
< TRANSISTOR > *****************************

Q501 8-729-119-78 TRANSISTOR 2SC2785-HFE < CAPACITOR >

Q502 8-729-178-42 TRANSISTOR 2SC2784-F
Q503 8-729-119-78 TRANSISTOR 2SC2785-HFE 0 C2 1-113-924-11 CERAMIC 0.0047uF 20% 250V
Q504 8-729-029-86 TRANSISTOR DTC124ESA
Q505 8-729-119-78 TRANSISTOR 2SC2785-HFE < CONNECTOR >

< RESISTOR > CN1 1-564-321-00 PIN, CONNECTOR (3.96mm PITCH) 2P

* CN2 1-580-230-11 PIN, CONNECTOR (PC BOARD) 2P
R205 1-247-879-91 CARBON 100K 5% 1/4W
R206 1-249-429-11 CARBON 10K 5% 1/4W < FUSE HOLDER >
R207 1-249-429-11 CARBON 10K 5% 1/4W
R208 1-249-429-11 CARBON 10K 5% 1/4W FH901 1-533-217-41 HOLDER, FUSE
R209 1-247-879-91 CARBON 100K 5% 1/4W FH951 1-533-217-41 HOLDER, FUSE
************************************************************
R210 1-247-895-00 CARBON 470K 5% 1/4W
R211 1-247-887-00 CARBON 220K 5% 1/4W SWITCH BOARD, COMPLETE
R212 1-247-863-91 CARBON 22K 5% 1/4W ***********************
R213 1-247-863-91 CARBON 22K 5% 1/4W
R214 1-247-887-00 CARBON 220K 5% 1/4W < CAPACITOR >

R216 1-249-429-11 CARBON 10K 5% 1/4W 0 C901 1-113-924-11 CERAMIC 0.0047uF 20% 250V
R217 1-247-879-91 CARBON 100K 5% 1/4W
R301 1-247-847-91 CARBON 4.7K 5% 1/4W < CONNECTOR >
R302 1-247-871-91 CARBON 47K 5% 1/4W
R303 1-249-413-11 CARBON 470 5% 1/4W CN3 1-564-321-00 PIN, CONNECTOR (3.96mm PITCH) 2P

The components identified by mark 0 or Les composants identifiés par une marque
dotted line with mark 0 are critical for 0 sont critiques pour la sécurité.
safety. Ne les remplacer que par une pièce portant
Replace only with part number specified. le numéro spécifié.

10
 SA-WMSP76

SWITCH
Ref. No. Part No. Description Remarks
* CN901 1-564-517-11 PLUG, CONNECTOR 2P

< DIODE >

D901 8-719-057-10 DIODE LNJ301MPUJAB (POWER)

< SWITCH >

0S901 1-554-920-11 SWITCH, PUSH (AC POWER) (1 KEY) (POWER)

************************************************************

MISCELLANEOUS
**************

0 57 1-696-847-22 CORD, POWER (AUS)

0 57 1-769-744-11 CORD, POWER (UK, AEP, MY, SP)
0 57 1-783-820-11 CORD, POWER (US, CND)
0 F901 1-532-463-51 FUSE (T1AL/250V) (EXCEPT US, CND)
0 F901 1-533-450-12 FUSE, GLASS TUBE (DIA. 5) (T2.5AL/125V)
(US, CND)

SP1 1-529-995-13 SPEAKER (20cm) (US, CND)

SP1 1-825-004-13 SPEAKER (20cm) (EXCEPT US, CND)
0 T1 1-439-627-11 TRANSFORMER, POWER (EXCEPT US, CND)
0 T1 1-439-628-11 TRANSFORMER, POWER (US, CND)

The components identified by mark 0 or Les composants identifiés par une marque
dotted line with mark 0 are critical for 0 sont critiques pour la sécurité.
safety. Ne les remplacer que par une pièce portant
Replace only with part number specified. le numéro spécifié.

11
SA-WMSP76

REVISION HISTORY

Clicking the version allows you to jump to the revised page.

Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.

Ver. Date Description of Revision

1.0 2004.03 New
1.1 2004.07 Addition of HT-4800DP to 1-page note (SPM-04067)