Scribd
Upload
1K views3 pages

Regulación de Valvulas Lovol 3,4,6

The document discusses valve timing and clearance checks for 3, 4, and 6 cylinder engines. It provides the firing order for a 3 cylinder engine as 1,2,3. It lists the correct valve clearances as 0.20 mm for inlet valves and 0.45 mm for exhaust valves. For 4 cylinder engines, it gives the procedure to check valves 1-4 by setting specific valves and then checking the next cylinder. A similar process is outlined for the 6 cylinder engine.

Uploaded by

Daniel Alejandro Delgado
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
1K views3 pages

Regulación de Valvulas Lovol 3,4,6

The document discusses valve timing and clearance checks for 3, 4, and 6 cylinder engines. It provides the firing order for a 3 cylinder engine as 1,2,3. It lists the correct valve clearances as 0.20 mm for inlet valves and 0.45 mm for exhaust valves. For 4 cylinder engines, it gives the procedure to check valves 1-4 by setting specific valves and then checking the next cylinder. A similar process is outlined for the 6 cylinder engine.

Uploaded by

Daniel Alejandro Delgado
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Three cylinder engines

The firing sequence of three-cylinder engine is: 1,2,3. When No.1 cylinder is on its upper dead center, you can adjust

the valves indicated with bold font below and turn it with 360 degrees.

Three cylinders: inlet^exhaust^ exhaust^ inlet^ inlet^ exhaust

,QOHWH[KDXVW ,QOHWH[KDXVW ,QOHWH[KDXVW


  

4.23
How to check the valve tip clearances

These are checked between the top of the valve stem and the rocker lever (A), with the engine hot or cold. The correct
clearances are 0,20 mm (0,008 in) for inlet valves and 0,45 mm (0.018 in) for exhaust valves. The valve positions are
shown at (B).The order of the valve positions are shown at the table below.

Remark: Number 1 cylinder is at the front of the engine.

Four cylinder engines

1. Turn the crankshaft in the normal direction of rotation until the inlet valve (B8) of number 4 cylinder has just
opened and the exhaust valve (B7) of the same cylinder has not closed completely. Check the clearances of the
valves of number 1 cylinder and adjust them, if it is necessary.
2. Set the valves of number 2 cylinder (B3 and B4) as indicated above for number 4 cylinder. Then check/adjust the
clearances of the valves of number 3 cylinder (B5 and B6).
3. Set the valves of number 1 cylinder (B1 and B2).Then check/adjust the clearances of the valves of number 4
cylinder (B7 and B8).
4. Set the valves of number 3 cylinder (B5 and B6).Then check/adjust the clearances of the valves of number 2
cylinder (B3 and B4).

No. of 1 2 3 4
Cylinder and
Valve 1 2 3 4 5 6 7 8
Valve
I= inlet valve I E E I I E E I
E=Exhaust valve
4.24

Six cylinder engines

1. Turn the crankshaft in the normal direction of rotation until the inlet valve (A12) of number 6 cylinder has just
opened and the exhaust valve (A11) of the same cylinder has not closed completely. Check the clearances of the
valves (B1 and B2) of number 1 cylinder and adjust them, if it is necessary.
2. Set the valves of number 2 cylinder (A4 and A3) as indicated above for number 6 cylinder. Then check/adjust the
clearances of the valves of number 5 cylinder (A9 and A10).
3. Set the valves of number 4 cylinder (A8 and A7).Then check/adjust the clearances of the valves of number 3
cylinder (A5 and A6).
4. Set the valves of number 1 cylinder (A1 and A2).Then check/adjust the clearances of the valves of number 6
cylinder (A11 and A12).
5. Set the valves of number 5 cylinder (A9 and A10).Then check/adjust the clearances of the valves of number 2
cylinder (A3 and A4).
6. Set the valves of number 3 cylinder (A5 and A6).Then check/adjust the clearances of the valves of number 4
cylinder (A7 and A8).

No. of
1 2 3 4 5 6
Cylinder and
Valve 1 2 3 4 5 6 7 8 9 10 11 12
Valve
I= inlet valve I E E 1 1 E E 1 I E E 1
E=Exhaust valve

You might also like