Scribd
Upload
110 views

Errorlist en 1 23

This document lists errors and warnings for protection devices on a VISU 23 system. It includes 28 error codes related to issues like exceeding temperature limits, sensor faults, phase failures, and more. It also includes 7 warning codes for potential issues like phase imbalance, undervoltage, and unusually quick increases in motor temperature. Each error or warning is given a number, short text, type as either "Error" or "Warning", and a brief description of the issue.

Uploaded by

bnx5dkq786
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
110 views

Errorlist en 1 23

This document lists errors and warnings for protection devices on a VISU 23 system. It includes 28 error codes related to issues like exceeding temperature limits, sensor faults, phase failures, and more. It also includes 7 warning codes for potential issues like phase imbalance, undervoltage, and unusually quick increases in motor temperature. Each error or warning is given a number, short text, type as either "Error" or "Warning", and a brief description of the issue.

Uploaded by

bnx5dkq786
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Fehlerliste Schutzgeräte VISU 23

No. error text art description


Engine temperature, Static switch-off Error Permissible motor temperature exceeded
2
Resistance value of the sensor > Trip value
(standard 4.5 kOhm)

Motor temperature, Dynamic switch- Error Temperature increase in the motor winding was
3
off unusually quick

Motor temperature, Dynamic switch- Error Temperature increase in the motor winding was
4
off unusually quick

Motor temperature, short circuit Error Sensor input motor temperature has detected a
8
short circuit

Sensor input Motor temperature has Error Sensor input Motor temperature has detected an
10
detected an open circuit open circuit

Permissible discharge gas Error Permissible discharge gas temperature exceeded


12
temperature exceeded

Sensor input discharge gas Error Sensor input discharge gas temperature has
13
temperature has detected a short detected a short circuit
circuit

Sensor input discharge gas Error Sensor input discharge gas temperature has
14
temperature has detected a open detected a open circuit
circuit

Motor temperature too high after Error After a mains reset, the resistance value of the
15
reset motor sensor is above the reset limit
time stamp can be shifted from here on.

Discharge gas temperature too high Error After a mains reset, the resistance value of the
16
after mains reset hot gas sensor is above the reset limit
time stamp can be shifted from here on.

Sensor screwed in wrong Error The oil differential pressure sensor does not
18
provide the correct signal, either it is not screwed
in correctly or there is a defect.

Oil differential pressure too low Error The compressor is running and the oil differential
19
pressure sensor reports a differential pressure to
the oil pump that is too low.

Sensor input oil differential pressure Error Sensor input oil differential pressure has detected
20
has detected a short circuit a short circuit

Incorrect phase sequence Error An incorrect phase sequence was found


27
Phase failure Error The percentage deviation of the amplitudes of the
28
phases was too large

Mittwoch, 5. Dezember 2018 1/2


Fehlerliste Schutzgeräte VISU 23

No. error text art description


Phase asymmetry Error The percentage deviation of the amplitudes of the
29
phases was too large

Sensor input Oil differential pressure Error Sensor input Oil differential pressure has detected
35
has detected an open circuit interruption

Wrong sensor Error Instead of the sensor 02 S 667, a sensor 02 S 666


36
was connected, the sensor has to be replaced.

overvoltage Error overvoltage


46
Current from sensor 1 has exceeded Error Current from sensor 1 has exceeded limit 1
47
trip point 1

Current from sensor 1 has exceeded Error Current from sensor 1 has exceeded limit 2
49
trip point 2

Sensor input current monitoring 1 has Error Sensor input current monitoring 1 has detected a
51
detected a short circuit short circuit

Sensor input current monitoring 1 has Error Sensor input current monitoring 1 has detected an
53
detected an open circuit interruption

Warning phase inbalance Warning Warning phase inbalance


110
Line undervoltage Warning Line undervoltage
116
Line voltage monitoring Warning Line voltage monitoring
117
Oil differential pressure too low Warning The compressor is running and the oil differential
119
pressure sensor reports a differential pressure to
the oil pump that is too low.

Dynamic warning; temperature Warning Temperature increase in the motor winding was
120
increase in the motor winding was unusually quick
unusually quick

Dynamic warning; temperature Warning Temperature increase in the motor winding was
121
increase in the motor winding was unusually quick
unusually quick

Neutral monitoring Warning Warning Neutral monitoring Warning


140

Mittwoch, 5. Dezember 2018 2/2

You might also like