Installation instructions, accessories

Volvo Car Corporation Gothenburg, Sweden

Instruction No Version Part. No.

31339589 1.2 31339587

Running board

IMG-229762

Equipment

IMG-345497 IMG-239664 IMG-333293 IMG-332313

© Volvo Car Corporation Running board- 31339589 - V1.2

Page 1 / 7
 Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden

IMG-352774

© Volvo Car Corporation Running board- 31339589 - V1.2

Page 2 / 7
 Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden

INTRODUCTION

Read through all of the instructions before starting installation.

Notifications and warning texts are for your safety and to

minimise the risk of something breaking during installation.

Ensure that all tools stated in the instructions are available

before starting installation.

Certain steps in the instructions are only presented in the form

of images. Explanatory text is also given for more complicated
steps.

In the event of any problems with the instructions or the

accessory, contact your local Volvo dealer.

Wash clean under the door sills, in front of the rear wheels and
behind the front wheels, on the right and left-hand sides.

Raise the car.

Note!

Ensure that the lifting tool does not block the location where
the Running board is to be attached.

Remove the two M10 screws from the front bottom flange and
the two M12 screws at the rear, on the right and left-hand sides.
Place the screws to one side, they will not be reused.

Clean the mating surfaces, where the Running board is to be

attached, from dirt and any underseal.

R8101617

Take an aluminium profile, one mounting for each, four M8

screws and washers from the kit. Install the mountings in the
aluminium profile as illustrated and screw in the four M8 screws.
Check that there is no play between the aluminium profile and
the mounting brackets at (A). Torque tighten the M8 screws to
25 Nm (19 lbf. ft).

Perform the same for the other aluminium profile.

IMG-352775

© Volvo Car Corporation Running board- 31339589 - V1.2

Page 3 / 7
 Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden

Hint

It is recommended that two people help when installing the

Running board.

Install the Running board with the M10 (1) and M12 (2) screws
with relevant washers.

R8101618

Tighten the M10 (1) screws to 50 Nm (37.5 lbf. ft) and the M12
(2) to 80 Nm (60 lbf. ft).

R8101807

Running board, Foot step

Note!

During installation the underlying surface must be kept at a

temperature of at least +15°C (59°F).

Do not wash the car within 48 hours after installation is

completed.

Allow the car to remain inside for at least two hours after
installation is completed if outside temperature is less than
+15°C (59°F).

© Volvo Car Corporation Running board- 31339589 - V1.2

Page 4 / 7
 Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden

Wash the "Running board" clean on the top and along the sides.

Wipe dry.

IMG-229765

Measure 170 mm (6 11/16") from the front joint between the

"Running board" profile and the mounting as illustrated.

Mark with pencil.

IMG-229766

© Volvo Car Corporation Running board- 31339589 - V1.2

Page 5 / 7
 Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden

Measure 70 mm (2 3/4") from the rear joint between the

"Running board" profile and the mounting as illustrated.

Mark with pencil.

IMG-229767

Align the foot steps to the "Running board" with the outer edge
at the pencil markings and in toward the centre of the "Running
board" as illustrated.

Check that the foot step is correctly aligned and draw around it
with a whiteboard pen.

IMG-229768

© Volvo Car Corporation Running board- 31339589 - V1.2

Page 6 / 7
 Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden

Remove the protective film from the three strips of tape.

IMG-229772

10

Hold the foot step slightly above the "Running board", inside the
markings drawn. Align the foot step in relation to the "Running
board" and check that the cut-outs in the foot step are opposite
the raised areas in the "Running board".

Lower the foot step and press it firmly into the "Running board".

Note!

Take care with the fit as the tape on the underside of the foot
step adheres immediately on contact with the surface.

Repeat the above for both sides and for all foot steps.

Wash away the markings.

IMG-229773

© Volvo Car Corporation Running board- 31339589 - V1.2

Page 7 / 7