ADEX CABLE TRAY

Adex Cable Tray

Metallic Adex cable trays are manufactured for the smooth and easy
pulling of cable from one point to another to BS EN 61537:2002. We have
designed the best cable trays, by taking care of Cable loads and practical
site problems. Wherever possible all fitting are made of state of art single
piece construction. Slotting Patterns are in such a way that it enables the
easy cutting and joining at any point without drilling at site. Design allows
greater cable filling capacity and smooth turning at bends.

Product specification
Material and Finish

I Pregalvanized steel or Zinc plating after steel fabrication

(HDGBF) as per BS EN 10142
I Epoxy polyester Powder coating to any RAL colour

Types available
1. Light Duty Cable Tray (P Type)
2. Medium Duty Cable Tray (M Type)
3. Heavy Duty Cable Tray (R Type)

Standard sizes available in heavy duty cable tray

width x Height in mm
50 x 50 200x50 600 x 50
100 x 50 300x50 750 x 50
150 x 50 450x50 900 x 50
Sizes other than this also available to customer request.

Length
3 Meter as standard. Other lengths are also available.

Slotting Pattern
Slots along the length (A) (Standard)

Note : Dimension mentioned through out in the Catalogue is in mm, Unless otherwise stated.
Physical Details
Width Thickness Weight Kg/M
50 1.00 0.60
Light Duty Cable Tray

100 1.00 1.00

150 1.00 1.40
(P-Type)

200 1.20 2.12

300 1.20 3.12
450 1.50 4.56
600 1.50 7.50
with 12mm side height

Width Thickness Weight Kg/M

50 1.00 1.04
Medium Duty Cable Tray

100 1.00 1.44

150 1.00 1.84
200 1.20 2.68
(M-Type)

300 1.20 3.65

450 1.20 5.08
600 1.50 8.16
750 2.00 13.28
900 2.00 15.68
with 25mm side height

Width Thickness Weight Kg/M

50 1.00 1.44
100 1.20 2.21
Heavy Duty Cable Tray

150 1.20 2.69

(R-Type)

200 1.50 3.96

300 1.50 5.16
450 1.50 6.96
600 2.00 11.68
750 2.00 14.08
900 2.00 16.50
with 25mm side height

I The Thickness mentioned are as per our standard Handling and Storage
thickness. However customer can order different Cable tray cannot be used as a walkway, means not
thicknesses as per their requirement. suppose to withstand unusual excessive point loads.
I The above details are for guidance only. And not meant for torsional rigidity.
I The Thickness and weight shown are for cable tray Adex tray should store in site in dry, well ventilated
with Zinc plating after fabrication finish. conditions and away from dust to preserve
I Commercial Tolerance on Thickness Apply. appearance for internal installations.
I Contact Sales desk for fitting thickness. All cut edges of cable tray at site should be protected
by applying Zinc rich paint to avoid further corrosion.
Order Zinc rich paint separately.
Standard Perforated Adex Cable Tray

The width and height are the inside dimension of the tray. Only straight length needs coupler to join.
Couplers Should be ordered separately.

Light Duty Cable Tray

(L -Type)
t
Width

Cross Section

12
Medium Duty Cable Tray
(M - Type)
10
12 t 25
Width
Cross Section

Heavy Duty Cable Tray

(R - Type) 10
12 t 50
Width
Cross Section

Perforation details
Slotting Pattern
Type - L
8
45

25

25

Perforation details remain same for light duty,

medium duty and heavy duty cable trays.
Adex Cable Tray Fittings

All bends, tees (Except Vertical tee) and crosses shown are gusseted in shape and heavy duty in construction

90o Bend 45o Bend

Width Radius
Width Radius W R
W R
W 50 125
W 50 125
100 125
100 125
150 150
150 150
200 150
200 150
300
300 and 250
R and 250 above
above
R
Two 45o bends can be used to achieve offsets in horizontal
Bends are available in 30 and 60 degrees also direction.

Adjustable Horizontal bend Horizontal Equal Tee

Width Radius
W R
50 125
W 100 125
150 150
200 150
Adjustable Horizontal Bends are available only upto and
including 300mm width R 300
and 250
above
R

Straight Section
Horizontal Unequal Tee Vertical Tee
Branch

W1

W1 W2

When ordering Horizontal Unequal Tee - Please order

in the form of W1-W2 to fill the width column.

For any unequal Tee order, maintaining width (W1) of the Straight section identical
by adding appropriate reducer where ever necessary. Width of the branches (W2)
can be vary from straight section.

Radius type fittings are also available on request. Put R in the column of type of Curvature.
Contact sales desk for various light and medium duty fittings.
Adex Cable Tray Fittings

Horizontal Cross Y Branch Left and Right

Width Radius W1 W1
W R W2 W2
50 125
100 125
W
150 150
200 150
W1 W1
300
R
and 250 Right Left
above
R X Cable is deviated t 45o from the main line

90o Riser outside 90o Riser Inside

Radius 300

Left

Risers are also available in 30, 45 and 60 degree

Straight Reducer Right Reducer Left Reducer

W1
W1 W1

W2 W2
W2

Note : Mention big dimension W1 first followed by W2 to fill the width column while ordering reducers.
Cable Tray Accessories

Couplers are supplied in pairs with eight sets of M6 x 16 mm roofing bolts, nuts & washers. Order the same
fastenings to join fittings with cable tray.

Wrap over Coupler Bend Coupler Plate Coupler

Adjustable Adjustable Blind End

Horizontal Coupler Vertical Coupler

for vertical change of direction.

Shown is one set of Coupler. Needs For ordering mention Width and
For horizontal change of direction two sets to join two trays height of the Cable Tray

Fish Plate Drop out U Coupler

Special for 50mm wide tray only

Radius 300mm

Trays above 450mm wide need

fish plates to avoid sagging at joint Mention width of tray while ordering Order in single to join two trays
 Support Systems for Adex cable tray
I While ordering cantilever bracket and cantilever arm a safe working distance of 30mm is to be added
to width of the tray. E.g : for 100mm tray DEB 130
Supplied without fastenings, Choose various types of fastenings.

Cantilever Bracket Single Cantilever arm Double Cantilever arm

Width R
130 50
160 50
230 50
330 75
30 480 100
M6x2 ROOF HEAD BOLT 630 150
NUT & WASHER TRAY FIXED
780 150 WITH SPRING NUT M6 &
TRAY FIXED M6x2D ROOF HEAD BOLT
WITH SPRING NUT M6 &
M6x2D ROOF HEAD BOLT
X
X
X

120
80
A

826826
413
X X X X X
X X
X X X X
X X X X
2 Holes of 50 X
14mm dia 2 Holes of 14mm dia 50
2 Holes of 14mm dia

L UDL L UDL
DEB 130 170 DED 180 750*
DEB 180 160 L UDL DED 230 660*
DEB 230 155 DEC 180 550 DED 330 600*
DEB 330 140 DEC 230 370 DED 480 380*
DEB 480 110 DEC 330 270 DED 630 305
DEB 630 100 DEC 480 175 DED 780 210
DEB 780 130 DEC 630 140 DED 930 175

L - length of the arm * Slip limits loading capacity when using in

UDL - Uniformly distributed load n kgf Strut Channel as column.

Stand off Bracket Trapeze Hanger I-Beam Cantilever arm

Use with 40mm wide I-Beam
40

2 Holes of 14mm dia

L L UDL
SEB 100 41 x 21 (DB 200 Series) Channel is DEI 130 105
SEB 150 recommended for trays up to 200mm width. DEI 180 94
SEB 200 For 300mm onwards use 41 x 41 DEI 230 90
SEB 300 (DB 100 Series). Can be ordered in slotted DEI 330 85
SEB 450 profile in 3 meter. See Apex Strut Channel DEI 480 74
SEB 600 section for ordering information. DEI 630 68
SEB 750
SEB 900

* Please note that above given loads are for general guidelines only.
* For Cable trays above 600mm width order double cantilever arm to increase safe working load
Cable Tray Covers and Fixing Details
Straight Cover upto 300mm needs four sets of Clamps. Fittings normally needs four Clamps for wider ones 5 Clamps needed.
450mm and above needs six clamps to fix cover. Re-inforcing type of profile is used in wider covers.
Normal flange height of cover ic 12mm. Covers equal to and above 600mm can be available in 1.5 meter long.

Solid Flange Cover Dome Type Cover

M6 x 10mm

Order Side Cover Clamp (SFA) and M6 x 10mm Roofing Order Side Cover Clamp (DFA) and 2 Sets of M6 x 10mm
bolt separately. Roofing bolt, Nut & Washer separately.

Louvered Cover Raised Ventilated Cover

Order Side Cover Clamp (LFA) and M6 x 10mm Order Side Cover Clamp (VFA) and 2Sets of M6 x 10mm
Roofing bolt separately. Roofing bolt, Nut & Washer separately.

Solid Flange Cover for Fittings Raised Ventilated Cover for Fittings

Order Side Cover Clamp (SFA) and M6 x 10mm Roofing bolt Order Side Cover Clamp (VFA) and M6 x 10mm Roofing
separately. (shown is a Tee Cover ) bolt, Nut & Washer separately.

Catalogue No of Side Cover Clamps (SCC)

Item / Des. Material Finish Type Side Height Abbreviation

Solid Flange SFA SCC

Dome Type DFA SCC

Raised Ventilated VFA SCC
Louvered LFA SCC