Copyright 2018 AIA MasterSpec Full Length 09/18

PRODUCT MASTERSPEC LICENSED BY AVITRU, LLC TO OATEY

This Product MasterSpec Section is licensed by AVITRU, LLC to Oatey ("Licensee").

This Product MasterSpec Section modifies the original MasterSpec text and does not include the
full content of the original MasterSpec Section.

Revisions made to the original MasterSpec text are made solely by the Licensee and are not endorsed by,
or representative of the opinions of, Avitru or The American Institute of Architects (AIA). Neither AIA
nor Avitru are liable in any way for such revisions or for the use of this Product MasterSpec Section by
any end user. A qualified design professional should review and edit the document to suit project
requirements.

For more information, contact Oatey, 20600 Emerald Pkwy, Cleveland, OH 44135; Phone: (216) 267-
7100; Website: www.oatey.com; Email: [email protected].

For information about MasterSpec, contact Avitru at (800) 424-5080 or visit www.avitru.com.

SECTION 221319.13 - SANITARY DRAINS

TIPS:

To view non-printing Editor's Notes that provide guidance for editing, click on MasterWorks/Single-File
Formatting/Toggle/Editor's Notes.

To read detailed research, technical information about products and materials, and coordination
checklists, click on MasterWorks/Supporting Information.

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including General and Supplementary
Conditions and Division 01 Specification Sections, apply to this Section.

1.2 SUMMARY

A. Section Includes:

1. Floor drains.
2. Floor sinks.
3. Trench drains.
4. Channel drainage systems.

1.3 DEFINITIONS

A. ABS: Acrylonitrile-butadiene styrene.

SANITARY DRAINS 221319.13 - 1

Copyright 2018 AIA MasterSpec Full Length 09/18
PRODUCT MASTERSPEC LICENSED BY AVITRU, LLC TO OATEY

B. FRP: Fiberglass-reinforced plastic.

C. HDPE: High-density polyethylene.

D. PE: Polyethylene.

E. PP: Polypropylene.

F. PVC: Polyvinyl chloride.

1.4 ACTION SUBMITTALS

A. Product Data: For each type of product.

PART 2 - PRODUCTS

2.1 DRAIN ASSEMBLIES

A. Sanitary drains shall bear label, stamp, or other markings of specified testing agency.

B. Comply with NSF 14 for plastic sanitary piping specialty components.

2.2 FLOOR DRAINS

A. Cast-Iron Floor Drains <Insert drawing designation if any>:

1. Manufacturers: Subject to compliance with requirements, provide products by one of the

following:

a. Commercial Enameling Company.

b. Jay R. Smith Mfg. Co.
c. Josam Company.
d. MIFAB, Inc.
e. Prier Products, Inc.
f. Sioux Chief Manufacturing Company, Inc.
g. Wade; a subsidiary of McWane Inc.
h. WATTS.
i. Zurn Industries, LLC.
j. <Insert manufacturer's name>.

2. Standard: ASME A112.6.3[ with backwater valve].

3. Pattern: [Area] [Floor] [Funnel floor] [Sanitary] <Insert pattern> drain.
4. Body Material: [Gray iron] <Insert material>.
5. Seepage Flange: [Not required] [Required].
6. Anchor Flange: [Not required] [Required].
7. Clamping Device: [Not required] [Required].
8. Outlet: [Bottom] [Side] <Insert type>.

SANITARY DRAINS 221319.13 - 2

Copyright 2018 AIA MasterSpec Full Length 09/18
PRODUCT MASTERSPEC LICENSED BY AVITRU, LLC TO OATEY

9. Backwater Valve: [Drain-outlet type] [Integral, ASME A112.14.1, swing-check type]

[Not required].
10. Coating on Interior and Exposed Exterior Surfaces: [Acid-resistant enamel] [Not
required] <Insert material>.
11. Sediment Bucket: [Not required] <Insert description>.
12. Top or Strainer Material: [Bronze] [Gray iron] [Nickel bronze] [Stainless steel]
<Insert material>.
13. Top of Body and Strainer Finish: [Nickel bronze] [Polished bronze] [Rough bronze]
[Stainless steel] <Insert finish>.
14. Top Shape: [Round] [Square] <Insert shape>.
15. Dimensions of Top or Strainer: <Insert dimensions and describe body, sump, and
grate>.
16. Top Loading Classification: [Extra Heavy Duty] [Heavy Duty] [Light Duty] [Medium
Duty] <Delete if not applicable>.
17. Funnel: [Not required] [Required] <Insert description and dimensions>.
18. Inlet Fitting: [Not required] [Gray iron, with threaded inlet and threaded or spigot
outlet, and trap-seal primer valve connection].
19. Trap Material: [Bronze] [Cast iron] [Copper] [Not required] <Insert material>.
20. Trap Pattern: [Deep-seal P-trap] [Standard P-trap] [Not required] <Insert pattern>.
21. Trap Features: [Cleanout] [Trap-seal primer valve drain connection] [Cleanout and
trap-seal primer valve drain connection] [Not required] <Insert type>.

B. Stainless Steel Floor Drains, ASME A112.3.1 <Insert drawing designation if any>:

1. Manufacturers: Subject to compliance with requirements, provide products by the

following:

a. Zurn Industries, LLC.

b. <Insert manufacturer's name>.

2. Outlet: [Bottom] [Side] <Insert type>.

3. Top or Strainer Material: [Stainless steel] <Insert material>.
4. Top Shape: [Round] [Square] <Insert shape>.
5. Dimensions of Top or Strainer: <Insert dimensions and describe body, sump, and
grate>.
6. Seepage Flange: [Not required] [Required].
7. Anchor Flange: [Not required] [Required].
8. Clamping Device: [Not required] [Required].
9. Trap-Primer Connection: [Not required] [Required].
10. Trap Material: [Cast iron] [Stainless steel] [Not required] <Insert material>.
11. Trap Pattern: [Deep-seal P-trap] [Standard P-trap] [Not required] <Insert pattern>.

C. Stainless-Steel Floor Drains, ASME A112.6.3 <Insert drawing designation if any>:

1. Manufacturers: Subject to compliance with requirements, provide products by one of the

following:

a. Jay R. Smith Mfg. Co.

b. Josam Company.
c. Kusel Equipment Co.
d. Scherping Systems, Inc.

SANITARY DRAINS 221319.13 - 3

Copyright 2018 AIA MasterSpec Full Length 09/18
PRODUCT MASTERSPEC LICENSED BY AVITRU, LLC TO OATEY

e. Sioux Chief Manufacturing Company, Inc.

f. Wade; a subsidiary of McWane Inc.
g. WATTS.
h. Zurn Industries, LLC.
i. <Insert manufacturer's name>.

2. Outlet: [Bottom] [Side] <Insert type>.

3. Top or Strainer Material: [Stainless steel] <Insert material>.
4. Top Shape: [Round] [Square] <Insert shape>.
5. Dimensions of Top or Strainer: <Insert dimensions and describe body, sump, and
grate>.
6. Seepage Flange: [Not required] [Required].
7. Anchor Flange: [Not required] [Required].
8. Clamping Device: [Not required] [Required].
9. Trap-Primer Connection: [Not required] [Required].
10. Trap Material: [Cast iron] [Stainless steel] [Not required] <Insert material>.
11. Trap Pattern: [Deep-seal P-trap] [Standard P-trap] [Not required] <Insert pattern>.

D. Plastic Floor Drains <Insert drawing designation if any>:

1. Basis-of-Design Product: Subject to compliance with requirements, provide Oatey;

Plastic Floor Drains or comparable product by one of the following:

a. Canplas LLC.
b. IPS Corporation.
c. Josam Company.
d. Plastic Oddities.
e. Sioux Chief Manufacturing Company, Inc.
f. Zurn Industries, LLC.
g. <Insert manufacturer's name>.

2. Standard: ASME A112.6.3.

3. Material: [ABS] [or] [PVC].
4. Seepage Flange: Not required.
5. Clamping Device: Not required.
6. Outlet: Bottom.
7. Sediment Bucket: Not required.
8. Top or Strainer Material: [Brass] [Plastic] [Stainless steel].
9. Top of Body and Strainer Finish: [Black] [White] [Stainless steel].
10. Top Shape: [Round] [Square].
11. Dimensions of Top or Strainer: [3.5 inches (89 mm)] [4 inches (102 mm)] [5 inches
(127 mm)].
12. Trap Material: Plastic drainage piping.
13. Trap Pattern: Standard P-trap.

2.3 FLOOR SINKS

A. Cast-Iron Floor Sinks <Insert drawing designation if any>:

SANITARY DRAINS 221319.13 - 4

Copyright 2018 AIA MasterSpec Full Length 09/18
PRODUCT MASTERSPEC LICENSED BY AVITRU, LLC TO OATEY

1. Manufacturers: Subject to compliance with requirements, provide products by one of the

following:

a. Commercial Enameling Company.

b. Jay R. Smith Mfg. Co.
c. Josam Company.
d. Wade; a subsidiary of McWane Inc.
e. Watts; a Watts Water Technologies company.
f. Zurn Industries, LLC.
g. <Insert manufacturer's name>.

2. Standard: ASME A112.6.7.

3. Pattern: [Floor] [Funnel floor] <Insert pattern> drain.
4. Body Material: Cast iron.
5. Anchor Flange: [Not required] [Required][, with seepage holes].
6. Clamping Device: [Not required] [Required].
7. Outlet: Bottom, [no-hub] <Insert type> connection.
8. Coating on Interior Surfaces: [Not required] [Acid-resistant enamel] <Insert coating>.
9. Sediment Bucket: [Not required] <Insert description>.
10. Internal Strainer: [Not required] [Dome] [Flat].
11. Internal Strainer Material: [Aluminum] <Insert material>.
12. Top Grate Material: [Cast iron] <Insert material>[, loose][, hinged].
13. Top of Body and Grate Finish: [Nickel bronze] [Acid-resistant enamel] <Insert
finish>.
14. Top Shape: [Round] [Square] <Insert shape>.
15. Dimensions of Top Grate: <Insert dimensions and describe grate pattern>.
16. Top Loading Classification: [No traffic] <Insert traffic loading>.
17. Funnel: [Not required] [Required]. <Insert material, shape and dimensions>.
18. <Insert additional options here>.

B. Stainless-Steel Floor Sinks, ASME A112.6.7 <Insert drawing designation if any>:

1. Manufacturers: Subject to compliance with requirements, provide products by one of the

following:

a. Jay R. Smith Mfg. Co.

b. Josam Company.
c. Wade; a subsidiary of McWane Inc.
d. Watts; a Watts Water Technologies company.
e. Zurn Industries, LLC.
f. <Insert manufacturer's name>.

2. Standard: ASME A112.6.7.

3. Pattern: [Floor] [Funnel floor] <Insert pattern> drain.
4. Body Material: Stainless steel.
5. Anchor Flange: [Not required] [Required][, with seepage holes].
6. Clamping Device: [Not required] [Required].
7. Outlet: Bottom, [no-hub] <Insert type> connection.
8. Sediment Bucket: [Not required] <Insert description>.
9. Internal Strainer: [Not required] [Dome] [Flat].
10. Internal Strainer Material: [Stainless steel] <Insert material>.

SANITARY DRAINS 221319.13 - 5

Copyright 2018 AIA MasterSpec Full Length 09/18
PRODUCT MASTERSPEC LICENSED BY AVITRU, LLC TO OATEY

11. Top Grate Material: [Stainless steel] <Insert material>[, loose][, hinged].
12. Top of Body and Grate Finish: [Satin nickel] [Stainless steel] <Insert finish>.
13. Top Shape: [Round] [Square] <Insert shape>.
14. Dimensions of Top Grate: <Insert dimensions and describe grate pattern>.
15. Top Loading Classification: [No traffic] <Insert traffic loading>.
16. Funnel: [Not required] [Required]. <Insert material, shape and dimensions>.
17. <Insert additional options here>.

C. Plastic Floor Sinks <Insert drawing designation if any>:

1. Manufacturers: Subject to compliance with requirements, provide products by one of the

following:

a. Canplas, LLC.
b. IPS Corporation.
c. Josam Company.
d. Plastic Oddities.
e. Sioux Chief Manufacturing Company, Inc.
f. Zurn Industries, LLC.
g. <Insert manufacturer's name>.

2. Standard: ASME A112.6.7.

3. Pattern: [Floor] [Funnel floor] <Insert pattern> drain.
4. Body Material: PVC.
5. Outlet: Bottom, PVC primer and solvent cement connection.
6. Sediment Bucket: [Not required] <Insert description>.
7. Internal Strainer: [Not required] [Dome] [Flat].
8. Internal Strainer Material: [PVC] <Insert material>.
9. Top Grate Material: [PVC] <Insert material>.
10. Top Shape: [Round] [Square] <Insert shape>.
11. Dimensions of Top Grate: <Insert dimensions and describe grate pattern>.
12. Top Loading Classification: [No traffic] <Insert traffic loading>.
13. Funnel: [Not required] [Required]. <Insert material, shape and dimensions>.
14. <Insert additional options here>.

2.4 TRENCH DRAINS

A. Trench Drains <Insert drawing designation if any>:

1. Manufacturers: Subject to compliance with requirements, provide products by one of the

following:

a. Jay R. Smith Mfg. Co.

b. Josam Company.
c. MIFAB, Inc.
d. Sioux Chief Manufacturing Company, Inc.
e. Wade; a subsidiary of McWane Inc.
f. WATTS.
g. Zurn Industries, LLC.
h. <Insert manufacturer's name>.

SANITARY DRAINS 221319.13 - 6

Copyright 2018 AIA MasterSpec Full Length 09/18
PRODUCT MASTERSPEC LICENSED BY AVITRU, LLC TO OATEY

2. Standard: ASME A112.6.3 for trench drains.

3. Material: Ductile or gray iron.
4. Flange: [Anchor] [Seepage] [Not required].
5. Clamping Device: [Not required] [Required].
6. Outlet: [Bottom] [End] [Side] <Insert location>.
7. Grate Material: [Ductile iron] [Ductile iron or gray iron] [Gray iron] [Stainless steel]
<Insert material>.
8. Grate Finish: [Painted] [Not required] <Insert finish>.
9. Dimensions of Frame and Grate: <Insert dimensions and describe body, sump, and
grate if required>.
10. Top Loading Classification: [Extra Heavy Duty] [Heavy Duty] [Light Duty] [Medium
Duty] <Delete if not applicable>.
11. Trap Material: [Cast iron] [Stainless steel] [Not required] <Insert material>.
12. Trap Pattern: [Standard P-trap] [Not required] <Insert pattern>.

2.5 CHANNEL DRAINAGE SYSTEMS

A. Stainless-Steel Channel Drainage Systems, ASME A112.3.1 <Insert drawing designation if

any>:

1. Manufacturers: Subject to compliance with requirements, provide products by the

following:

a. Josam Company.
b. <Insert manufacturer's name>.

2. Description: Modular system of stainless steel channel sections, grates, and

appurtenances; designed so grates fit into channel recesses without rocking or rattling.
3. Standard: ASME A112.3.1 for trench drains.
4. Channel Sections: Interlocking joint, stainless steel with level invert.

a. Dimensions: [5.8 inches (147 mm)] [11.7 inches (297mm)] wide. Include number
of units required to form total lengths indicated.

5. Grates: Manufacturer's designation "[heavy] [medium] duty," with slots or perforations,

and of width and thickness that fit recesses in channels.

a. Material: [Ductile iron] [Fiberglass] [Galvanized steel] [Gray iron] [Stainless

steel] <Insert material>.
b. Locking Mechanism: [Manufacturer's standard device for securing grates to
channel sections] [Not required].

6. Covers: Solid [ductile or gray iron] [stainless steel] <Insert material>, of width and
thickness that fit recesses in channels, and of lengths indicated.
7. Supports, Anchors, and Setting Devices: Manufacturer's standard, unless otherwise
indicated.
8. Channel-Section Joining and Fastening Materials: As recommended by system
manufacturer.

SANITARY DRAINS 221319.13 - 7

Copyright 2018 AIA MasterSpec Full Length 09/18
PRODUCT MASTERSPEC LICENSED BY AVITRU, LLC TO OATEY

B. Stainless Steel Channel Drainage Systems, Non-ASME A112.3.1 <Insert drawing designation
if any>:

1. Manufacturers: Subject to compliance with requirements, provide products by one of the

following:

a. MultiDrain Systems, Inc.

b. Zurn Industries, LLC.
c. <Insert manufacturer's name>.

2. Description: Modular system of stainless steel channel sections, grates, and

appurtenances; designed so grates fit into channel recesses without rocking or rattling.
3. Channel Sections: Interlocking joint, stainless steel with level invert.

a. Dimensions: [6 inches (152 mm)] [12 inches (305 mm)] wide. Include number of
units required to form total lengths indicated.

4. Grates: Manufacturer's designation "[heavy] [medium] duty," with slots or perforations,

and of width and thickness that fit recesses in channels.

a. Material: [Ductile iron] [Fiberglass] [Galvanized steel] [Gray iron] [Stainless

steel] <Insert material>.
b. Locking Mechanism: [Manufacturer's standard device for securing grates to
channel sections] [Not required].

5. Covers: Solid [ductile or gray iron] [stainless steel] <Insert material>, of width and
thickness that fit recesses in channels, and of lengths indicated.
6. Supports, Anchors, and Setting Devices: Manufacturer's standard unless otherwise
indicated.
7. Channel-Section Joining and Fastening Materials: As recommended by system
manufacturer.

C. Narrow, Sloped-Invert, Polymer-Concrete Channel Drainage Systems <Insert drawing

designation if any>:

1. Manufacturers: Subject to compliance with requirements, provide products by one of the

following:

a. ABT, Inc.
b. ACO USA.
c. Forté Composites, Inc.
d. Jay R. Smith Mfg. Co.
e. Josam Company.
f. Polycast; Hubbell Power Systems, Inc.
g. <Insert manufacturer's name>.

2. Description: Modular system of channel sections, grates, and appurtenances; designed so

grates fit into channel recesses without rocking or rattling.
3. Channel Sections: Narrow, interlocking-joint, sloped-invert, polymer-concrete modular
units with end caps.

SANITARY DRAINS 221319.13 - 8

Copyright 2018 AIA MasterSpec Full Length 09/18
PRODUCT MASTERSPEC LICENSED BY AVITRU, LLC TO OATEY

a. Include rounded bottom, with built-in invert slope of 0.6 percent and with outlets
in number, sizes, and locations indicated.
b. Include extension sections necessary for required depth.
c. Dimensions: 4-inch (102-mm) inside width. Include number of units required to
form total lengths indicated.
d. Frame: [Gray iron or galvanized steel for grates] [Not required].

4. Grates: Manufacturer's designation "[heavy] [medium] duty," with slots or perforations,

and of width and thickness that fit recesses in channel sections.

a. Material: [Ductile iron] [Fiberglass] [Galvanized steel] [Gray iron] [Stainless

steel] <Insert material>.

1) Locking Mechanism: [Manufacturer's standard device for securing

grates to channel sections] [Not required].

5. Covers: Solid [ductile or gray iron] <Insert material>, of width and thickness that fit
recesses in channel sections, and of lengths indicated.
6. Supports, Anchors, and Setting Devices: Manufacturer's standard unless otherwise
indicated.
7. Channel-Section Joining and Fastening Materials: As recommended by system
manufacturer.

D. Narrow, Level-Invert, Polymer-Concrete Channel Drainage Systems <Insert drawing

designation if any>:

1. Manufacturers: Subject to compliance with requirements, provide products by one of the

following:

a. ABT, Inc.
b. ACO USA.
c. Forté Composites, Inc.
d. Josam Company.
e. <Insert manufacturer's name>.

2. Description: Modular system of channel sections, grates, and appurtenances; designed so

grates fit into channel recesses without rocking or rattling.
3. Channel Sections: Narrow, interlocking-joint, precast, polymer-concrete modular units
with end caps.

a. Include rounded bottom, with level invert and with NPS 4 (DN 100) outlets in
number and locations indicated.
b. Dimensions: [5-inch (127-mm)] <Insert dimension> inside width and [9-3/4
inches (248 mm)] <Insert dimension> deep. Include number of units required to
form total lengths indicated.

1) Frame: [Gray iron or galvanized steel for grates] [Not required].

4. Grates: Manufacturer's designation "[heavy] [medium] duty," with slots or perforations,

and of width and thickness that fit recesses in channel sections.

SANITARY DRAINS 221319.13 - 9

Copyright 2018 AIA MasterSpec Full Length 09/18
PRODUCT MASTERSPEC LICENSED BY AVITRU, LLC TO OATEY

a. Material: [Ductile iron] [Fiberglass] [Galvanized steel] [Gray iron] [Stainless

steel] <Insert material>.
b. Locking Mechanism: [Manufacturer's standard device for securing grates to
channel sections] [Not required].

5. Covers: Solid [ductile or gray iron] <Insert material>, of width and thickness that fit
recesses in channel sections, and of lengths indicated.
6. Supports, Anchors, and Setting Devices: Manufacturer's standard unless otherwise
indicated.
7. Channel-Section Joining and Fastening Materials: As recommended by system
manufacturer.

E. Wide, Level-Invert, Polymer-Concrete Channel Drainage Systems <Insert drawing

designation if any>:

1. Manufacturers: Subject to compliance with requirements, provide products by one of the

following:

a. ABT, Inc.
b. ACO USA.
c. Josam Company.
d. Polycast; Hubbell Power Systems, Inc.
e. <Insert manufacturer's name>.

2. Description: Modular system of channel sections, grates, and appurtenances; designed so

grates fit into channel recesses without rocking or rattling.
3. Channel Sections: Wide, interlocking-joint, precast, polymer-concrete modular units with
end caps.

a. Include flat or rounded bottom, with level invert and with outlets in number, sizes,
and locations indicated.
b. Dimensions: [8-inch (203-mm)] <Insert dimension> inside width and [13-3/4
inches (350 mm)] <Insert dimension> deep. Include number of units required to
form total lengths indicated.

1) Frame: [Gray iron or galvanized steel for grates] [Not required].

4. Grates: Manufacturer's designation "[heavy] [medium] duty," with slots or perforations,

and of width and thickness that fit recesses in channel sections.

a. Material: [Ductile iron] [Fiberglass] [Galvanized steel] [Gray iron] [Stainless

steel] <Insert material>.
b. Locking Mechanism: [Manufacturer's standard device for securing grates to
channel sections] [Not required].

5. Covers: Solid [ductile or gray iron] <Insert material>, of width and thickness that fit
recesses in channel sections, and of lengths indicated.
6. Supports, Anchors, and Setting Devices: Manufacturer's standard unless otherwise
indicated.
7. Channel-Section Joining and Fastening Materials: As recommended by system
manufacturer.

SANITARY DRAINS 221319.13 - 10

Copyright 2018 AIA MasterSpec Full Length 09/18
PRODUCT MASTERSPEC LICENSED BY AVITRU, LLC TO OATEY

F. FRP Channel Drainage Systems <Insert drawing designation if any>:

1. Manufacturers: Subject to compliance with requirements, provide products by one of the

following:

a. ACO USA.
b. Aquaduct, Inc.
c. Jay R. Smith Mfg. Co.
d. Zurn Industries, LLC.
e. <Insert manufacturer's name>.

2. Description: Modular system of channel sections, grates, and appurtenances; designed so

grates fit into channel recesses without rocking or rattling.
3. Channel Sections: Interlocking-joint, sloped-invert, FRP modular units, with end caps.
Include flat, rounded, or inclined inside bottom, with outlets in number, sizes, and
locations indicated.

a. Dimensions: [4 inches (102 mm)] [4 or 6 inches (102 or 152 mm)] [6 inches (152
mm)] [6 or 8 inches (152 or 203 mm)] [8 inches (203 mm)] wide. Include
number of units required to form total lengths indicated.
b. Frame: [Galvanized steel] [Stainless steel] [Manufacturer's standard metal]
<Insert material> for grates.

4. Grates: With slots or perforations and widths and thickness that fit recesses in channel
sections.

a. Material: [Fiberglass] [Galvanized steel] [Gray iron] [Stainless steel] <Insert

material>.
b. Locking Mechanism: [Manufacturer's standard device for securing grates to
channel sections] [Not required].

5. Covers: Solid [ductile or gray iron] <Insert material>, of width and thickness that fit
recesses in channel sections, and of lengths indicated.
6. Supports, Anchors, and Setting Devices: Manufacturer's standard unless otherwise
indicated.
7. Channel-Section Joining and Fastening Materials: As recommended by system
manufacturer.

G. HDPE or PE Channel Drainage Systems <Insert drawing designation if any>:

1. Manufacturers: Subject to compliance with requirements, provide products by one of the

following:

a. Jay R. Smith Mfg. Co.

b. Sioux Chief Manufacturing Company, Inc.
c. Tuf-Tite Corporation.
d. Zurn Industries, LLC.
e. <Insert manufacturer's name>.

2. Description: Modular system of channel sections, grates, and appurtenances; designed so

grates fit into channel recesses without rocking or rattling.

SANITARY DRAINS 221319.13 - 11

Copyright 2018 AIA MasterSpec Full Length 09/18
PRODUCT MASTERSPEC LICENSED BY AVITRU, LLC TO OATEY

3. Channel Sections: Interlocking-joint, HDPE or PE modular units, with end caps. Include
flat, rounded, or inclined bottom, with level invert and with outlets in number, sizes, and
locations indicated.

a. Dimensions: 4 inches (102 mm) wide. Include number of units required to form
total lengths indicated.

4. Grates: With slots or perforations and widths and thickness that fit recesses in channel
sections.

a. Material: [Fiberglass] [Galvanized steel] [Gray iron] [Stainless steel] <Insert

material>.
b. Color: <Insert color or delete subparagraph>.

5. Supports, Anchors, and Setting Devices: Manufacturer's standard, unless otherwise

indicated.
6. Channel-Section Joining and Fastening Materials: As recommended by system
manufacturer.

H. PP Channel Drainage Systems <Insert drawing designation if any>:

1. Manufacturers: Subject to compliance with requirements, provide products by one of the

following:

a. Infinity Plastics, Inc.

b. Jay R. Smith Mfg. Co.
c. <Insert manufacturer's name>.

2. Description: Modular system of channel sections, grates, and appurtenances; designed so

grates fit into channel recesses without rocking or rattling.
3. Channel Sections: Interlocking-joint, PP modular units, with end caps. Include flat,
rounded, or inclined bottom, with level invert and with outlets in number, sizes, and
locations indicated.

a. Dimensions: 4 inches (102 mm) wide. Include number of units required to form
total lengths indicated.

4. Grates: With slots or perforations and widths and thickness that fit recesses in channel
sections.

a. Material: [Fiberglass] [Galvanized steel] [Gray iron] [Stainless steel] <Insert

material>.
b. Color: <Insert color or delete subparagraph>.

5. Supports, Anchors, and Setting Devices: Manufacturer's standard, unless otherwise

indicated.
6. Channel-Section Joining and Fastening Materials: As recommended by system
manufacturer.

I. PVC Channel Drainage Systems <Insert drawing designation if any>:

SANITARY DRAINS 221319.13 - 12

Copyright 2018 AIA MasterSpec Full Length 09/18
PRODUCT MASTERSPEC LICENSED BY AVITRU, LLC TO OATEY

1. Manufacturers: Subject to compliance with requirements, provide products by one of the

following:

a. MultiDrain Systems, Inc.

b. NDS Inc.
c. <Insert manufacturer's name>.

2. Description: Modular system of channel sections, grates, and appurtenances; designed so

grates fit into channel recesses without rocking or rattling.
3. Channel Sections: Interlocking-joint, PVC modular units, with end caps. Include flat,
rounded, or inclined bottom, with level invert and with outlets in number, sizes, and
locations indicated.

a. Dimensions: 4 inches (102 mm) wide. Include number of units required to form
total lengths indicated.

4. Grates: With slots or perforations and widths and thickness that fit recesses in channel
sections.

a. Material: [Fiberglass] [Galvanized steel] [Gray iron] [Stainless steel] <Insert

material>.
b. Color: <Insert color or delete subparagraph>.

5. Supports, Anchors, and Setting Devices: Manufacturer's standard, unless otherwise

indicated.
6. Channel-Section Joining and Fastening Materials: As recommended by system
manufacturer.

PART 3 - EXECUTION

3.1 INSTALLATION

A. Install floor drains at low points of surface areas to be drained. Set grates of drains flush with
finished floor, unless otherwise indicated.

1. Position floor drains for easy access and maintenance.

2. Set floor drains below elevation of surrounding finished floor to allow floor drainage.
3. Set with grates depressed in accordance with the following drainage area radii:

a. Radius, 30 Inches (750 mm) or Less: Equivalent to 1 percent slope, but not less
than 1/4-inch (6.35-mm) total depression.
b. Radius, 30 to 60 Inches (750 to 1500 mm): Equivalent to 1 percent slope.
c. Radius, 60 Inches (1500 mm) or Larger: Equivalent to 1 percent slope, but not
greater than 1-inch (25-mm) total depression.

4. Install floor-drain flashing collar or flange, so no leakage occurs between drain and
adjoining flooring.

a. Maintain integrity of waterproof membranes where penetrated.

SANITARY DRAINS 221319.13 - 13

Copyright 2018 AIA MasterSpec Full Length 09/18
PRODUCT MASTERSPEC LICENSED BY AVITRU, LLC TO OATEY

5. Install individual traps for floor drains connected to sanitary building drain unless
otherwise indicated.

B. Install trench drains at low points of surface areas to be drained.

1. Set grates of drains flush with finished surface, unless otherwise indicated.

C. Comply with ASME A112.3.1 for installation of stainless steel channel drainage systems.

1. Install on support devices, so that top will be flush with adjacent surface.

D. Install FRP channel drainage system components on support devices, so that top will be flush
with adjacent surface.

E. Install plastic channel drainage system components on support devices, so that top will be flush
with adjacent surface.

F. Install open drain fittings with top of hub [1 inch (25 mm)] [2 inches (51 mm)] <Insert
dimension> above floor.

3.2 CONNECTIONS

A. Comply with requirements in Section 221316 "Sanitary Waste and Vent Piping" for piping
installation requirements. Drawings indicate general arrangement of piping, fittings, and
specialties.

B. Comply with requirements in Section 221319 "Sanitary Waste Piping Specialties" for
backwater valves, air admittance devices and miscellaneous sanitary drainage piping specialties.

C. Comply with requirements in Section 221323 "Sanitary Waste Interceptors" for grease
interceptors, grease-removal devices, oil interceptors, sand interceptors, and solid interceptors.

D. Where installing piping adjacent to equipment, allow space for service and maintenance.

E. Ground equipment in accordance with Section 260526 "Grounding and Bonding for Electrical
Systems."

F. Connect wiring in accordance with Section 260519 "Low-Voltage Electrical Power Conductors
and Cables."

3.3 LABELING AND IDENTIFYING

A. Distinguish among multiple units, inform operator of operational requirements, indicate safety
and emergency precautions, and warn of hazards and improper operations, in addition to
identifying unit. Nameplates and signs are specified in Section 220553 "Identification for
Plumbing Piping and Equipment."

SANITARY DRAINS 221319.13 - 14

Copyright 2018 AIA MasterSpec Full Length 09/18
PRODUCT MASTERSPEC LICENSED BY AVITRU, LLC TO OATEY

3.4 PROTECTION

A. Protect drains during remainder of construction period to avoid clogging with dirt or debris and
to prevent damage from traffic or construction work.

B. Place plugs in ends of uncompleted piping at end of each day or when work stops.

END OF SECTION 221319.13

SANITARY DRAINS 221319.13 - 15