Scribd
Upload
197 views4 pages

BPI Specifications Rev 0

The document contains Sterlite Power Grid Ventures Ltd.'s standard specification for bus post insulators. It outlines requirements for insulators of different voltage levels including 800kV, 420kV, 245kV and below. It also specifies the tests insulators must pass, including visual examination, temperature cycling, mechanical strength, porosity, galvanizing and electrical tests. All insulators must conform to the relevant Indian and international standards.

Uploaded by

400KV
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
197 views4 pages

BPI Specifications Rev 0

The document contains Sterlite Power Grid Ventures Ltd.'s standard specification for bus post insulators. It outlines requirements for insulators of different voltage levels including 800kV, 420kV, 245kV and below. It also specifies the tests insulators must pass, including visual examination, temperature cycling, mechanical strength, porosity, galvanizing and electrical tests. All insulators must conform to the relevant Indian and international standards.

Uploaded by

400KV
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

The Specification, drawings and design details contained in this document are the property of STERLITE POWER GRID

VENTURES LTD. These

Standard Specification
for
Bus Post Insulators
shall not be reproduced, used or copied, except in the way permitted by the owner SPGVL.

SS-11-1009

00 07.08.2019 Issued as standard specification JC SM RS


Rev. Date Details Prepared Reviewed Approved
Document
Rev.
Number
Standard Specification for Bus Post Insulators
SS-11-1009 00
SS-11-1009 Rev 00 07-08-2019
Standard Specification for Bus Post Insulators

Revision History

Revision Date Remarks

Rev. 00 07.08.2019 First Issue

All Rights Reserved © Sterlite Power Grid Ventures Ltd Page 2 of 4


SS-11-1009 Rev 00 07-08-2019
Standard Specification for Bus Post Insulators

A Requirement of BPIs for 800 kV Equipment


A.1 For all applications/equipment except operating insulators
10kN
of Knee Break Isolators or Pantograph Isolator
B Requirement of BPIs for 420 kV Equipment
B.1 For Isolators 10kN
B.2 For normal support structures and Wave Trap 8 kN
C Requirement of BPIs for 245 kV and below Equipment
C.1 For all applications 8 kN
D Requirement of BPIs for 145 kV and below Equipment
D.1 For all applications 6 kN
E Requirement of BPIs for 72.5 kV and below Equipment
E.1 For all applications 6 kN
F Requirement of BPIs for 36 kV and below Equipment
F.1 For all applications 6 kN
Creepage distance of the insulator shall be as per respective project requirement.
G
Porcelain or Polymer any kind of BPI can be used, if any specific restriction not specified
H anywhere in the project documents
For any very very high pollution area / Coastline area installation if RTV quoting have
I been asked in the project document same to be considered for Porcelain insulator.
J Bus Post Insulators of all voltage level shall conform to the followings: -

Cl. No. 9.12 of IS: 2544 & 5.8 of IEC


1 Visual Examination
60168

Cl. No. 9.7 of IS: 2544 & 5.1 of IEC:


2 Verification of Dimensions
60168

Cl. No. 9.8 of IS: 2544 & 5.4 of IEC:


3 Temperature Cycle Test
60168

4 Mechanical Strength Test


Cl. No. 9.6.5.3 of IS: 2544 & 5.2.7 of
(i) Compressive Test
IEC: 60168
(After Compressive Test) Cl. No.
(ii)Tensile Test 9.6.5.3 of IS: 2544 & 5.2.6 of IEC:
60168
(After Tensile Test) Cl. No. 9.6.5.2 of IS:
(iii)Torsion Test
2544 & 5.2.5 of IEC: 60168
(After Torsion Test) Cl. No. 9.6.5.1 of
(iv) Bending Test
IS: 2544 & 5.2.4 of IEC: 60168

All Rights Reserved © Sterlite Power Grid Ventures Ltd Page 3 of 4


SS-11-1009 Rev 00 07-08-2019
Standard Specification for Bus Post Insulators

Cl. No. 9.10 of IS: 2544 & 5.6 of IEC:


5 Porosity Test
60168

6 Galvanising Test
(i)Uniformity of Zinc Coating On Metal
Cl. No. 9.11 of IS: 2544 & 5.7 of IEC:
Component: Top flange
60168
Bottom flange

(ii)Thickness of Zinc Coating On Metal


Component: Top flange Cl. No. 5.7 of IEC 60168
Bottom flange

As per RFP & SPGVL's requirement for


7 Visible Discharge Test
the project

Cl. No. 4.5 of IEC: 60168-2001 and as


8 Lightning Impulse Voltage withstand Test per RFP & SPGVL's requirement for
the project.

Cl. No. 4.5.2 of IEC: 60168-2001 and as


9 Lightning Impulse Voltage Flashover Test per RFP & SPGVL's requirement for the
project.

Cl. No. 4.7 of IEC: 60168-2001 and as


10 Dry Power Frequency Voltage Withstand Test per RFP & SPGVL's requirement for the
project.

Cl. No. 4.7.3 of IEC: 60168-2001 and as


11 Dry Power Frequency Voltage Flashover Test per RFP & SPGVL's requirement for
the project.

Cl. No. 4.8 of IEC: 60168-2001 and as


12 Wet Power Frequency Voltage Withstand Test per RFP & SPGVL's requirement for
the project.

Cl. No. 4.8.3 of IEC: 60168-2001 and as


13 Wet Power Frequency Voltage Flashover Test per RFP & SPGVL's requirement for
the project.

IEC: 60437-Latest Revision and as per


14 Radio Interference Test RFP & SPGVL's requirement for the
project.

NOTE- All the relevant standards specified above, their latest version to be used with
amendments if any time to time till the date of issuance of order for respective project.

All Rights Reserved © Sterlite Power Grid Ventures Ltd Page 4 of 4

You might also like