RAYMING PCB & ASSEMBLY
Differentiating between Conductive vs Non-conductive Via Fill PCB
Do you know that a via needs to be filled? After it has been used to
establish a connection between the circuit’s layers, you have to get them
filled. In this article, we help you understand the two major ways to get
this done.
Table of Contents
What is a Via?
It is the copper plated through-hole primarily used for connecting multiple
(two or more) layers in a Printed Circuit Board (PCB).
What is a Via Fill?
It simply refers to the filling or closure of the via. It is important to mention
that the filling or covering process is important, as it improves the
reliability of the connections.
Thus, you need to use any of the common via fill processes to close the
via’s holes.
What to Use for Via Fill?
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
It is common to use epoxy for covering the via holes. The choice of epoxy
for the process is borne out of the fact that the material supports the
retention of the solder at the assembly level. This allows for the reduced
risk of compromising the solder joints and to keep away the bath solution
from the surface.
Request PCB Manufacturing & Assembly Quote Now
Via-in-Pad vs. Through-Hole Technology
annular ring via
Today, you can choose between the through-hole technology and
via-in-pad for filling the via in a PCB.
It is best to stick to using the via-in-pad process as compared to the
through-hole process. The benefits to using it include:
Routing Density Improvement
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
The routing density (when measured in terms of the higher density per
layer), is improved.
Streamlined Signal Transfer Process
The via-in-pad process also streamlines the process of transferring the
signals. It is evident in the streamlined method of filling, planarizing and
plating the via over copper. This proves to be a better method when
compared to the traditional process of transferring the signal from
the Ball Grid Array (BGA), pass it through the via and then have it passed
on to the inner layers.
Additional benefits of using the via filling process are:
Reduction of the circuit board’s size, as well as the number of layers
used therein.
The filled vis process also does away with the high-speed design
constraints, especially low inductances.
It strengthens the pad’s attachments.
Filled vias also reduction the EMIs.
Increased thermal and electrical conductivity.
Through the use of filled vias, the high-frequency designs will have
shorter possible routes, for bypassing the capacitors.
What is Conductive Via Filling?
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
It is one of the via fill processes/options for circuit boards. It refers to the
process of initiating a transfer of electrical signals from one part of the
PCB to the other. At the same time, the via’s thermal transfer properties
are improved, while enabling the electrical signal transfer.
Conductive Via Filling Materials
You can choose between copper and silver epoxy for this purpose. The
major advantage to the two is the excellent thermal conducting property.
For example, you can rely on these materials to do the following:
The improved heat/thermal conductivity is accentuated by the
metallic design of the via fill. This sees to the excellent transfer of
heat from the Integrated Circuit (IC) to the other side of the PCB.
Once the heat is dissipated to the PCB’s side, it is further moved
away via the heatsink.
The major materials used here are the DuPont CB100 and the Tatsuto
AE3030 epoxy fill. With the two making up the “silver coated copper
particle” and filled with the epoxy matrix; they are ideal for the improved
thermal and electrical conductivities, even in a cured state.
Here are some of the additional points to note about these materials:
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
CTE Differences: there is a difference between the Tatsuto AE3030
and DuPont CB100, based on the Coefficient of Thermal Expansion
(CTE). This difference is based primarily on the CB100’s longer usage
and the fact that it comprises both a higher CTE and a larger particle
size.
The silver epoxy is used mostly and quite affordable, when
compared to the superior heat conductivity capabilities of the
copper conductive epoxy.
The use of a conductive polymer layer deposition
method significantly the flow of current between the internal layers
and vias of the circuit board. This is derived via the deposition
method’s placement on the PCB’s via-hole.
It is also possible to save up on costs via the conductive polymer
layer deposition method. This can be enhanced via the direct
metallization of the via hole’s inner walls.
Request PCB Manufacturing & Assembly Quote Now
What is Non-Conductive Via Fill?
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
This process is not entirely an opposite of the conductive via fill option,
because it is processed the same way as the latter.
However, the difference between the non-conductive via fill and the
conductive via fill is based on the purpose. While the non-conductive is
used for preventing the contamination of the via by solder and other
contaminants; the conductive option allows for the effecting both signal
and heat transfer.
Here are some of the additional benefits of the non-conductive via fill
process:
The plating of the vias also supports the conduction of electrical
signals and heat.
Non-conductive via fills also see to the creation of a structural
support for the copper pad that covers the holes.
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
Non-Conductive Via Fill Materials
Both Peters PP2795 and San-Ei Kagaku PHP-900 epoxy are the common
materials used for non-conductive via fills. The former has been enjoying
the many years of usage, but now has a fierce competition in San-Ei, which
has become a popular choice in recent years.
Conductive vs. Non-Conductive Via Fill Differences
The first difference between the two is that the conductive via fill
facilitates the transfer of electrical signals and heat, while the
non-conductive via fill primarily prevents contaminants from getting into
the via.
Depending on the PCB designer and targeted application, using the
non-conductive via fill option might be better. These reasons support the
claim:
Solder Bridging Prevention: the risks of solder bridging are greatly
reduced due to the stoppage of the solder mask on the filled vias a
few mils short of the pad. When used in the medium-density circuit
boards, it helps to prevent solder bridging between the nearby pad
and the via.
The fill materials for the non-conductive vias help to fill the gap that
contained air before.
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
CTE Value Matching
You also need to match the value of the Coefficient of Thermal Expansion
(CTE), as it pertains to the via filling to be applied. This matching is
important because of the reduced risks of stress-related fractures. These
fractures are commonly caused by the contraction or expansion triggered
by the same circumstances.
Here are some of the steps involved in the CTE value matching:
CTE & Surrounding Laminate
The first value matching should be between the surrounding laminate
material and the Coefficient of Thermal Expansion (CTE).
This comes in handy as the circuit board “lives off the life” in an on/off and
heating/cooling state of expansion and contraction of the padstack
structures.
Between Conductive and Non-Conductive Epoxies
Should you choose the conductive epoxy or go for the non-conductive
variant? Generally, the non-conductive variants are a better bet for the
CTE’s value matching. This is because they provide a more reliable overall
structure for matching the CTE to the laminate.
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
On the other hand, despite the widespread adoption of the
non-conductive epoxy; the conductive variant can also be used.
Considering the popularity of the DuPont CB100 as the best via fill, it is
evident why the conductive epoxies are still popular in some quarters.
The following reasons also support the necessity of using the conductive
epoxies for CTE’s value matching to laminate:
Conductive epoxies are ideal for use with the high pin count Ball
Grid Arrays (BGAs), especially the ones that “run hot.”
Conductive epoxies are a better option for the thermal vias. These
vias benefit from the epoxies’ capability of fast-tracking thermal
energy out and away from the originating source.
Legacy or older electronic products also benefit from conductive
epoxies. The usage is due to the long-standing popularity and
improved lifecycle properties.
Request PCB Manufacturing & Assembly Quote Now
Away from Conductive and Non-Conductive Via Fills
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
vias on pads
It is common for the non-conductive and the conductive via fills to be used
in covering the vias in a PCB. However, there is a third option, which is not
fully harnessed. The name is Copper-Plated Shut Filled Vias.
It is a filled vias process commonly used when the aspect ratio gets to 10:1.
You can also use it when the diameter is less than 8 mils.
Considerations for the Copper-Plated Shut Filled Vias
It is imperative to mention that the copper-plated shut filled vias can also
be prone to a couple of challenges. The following are some of the things
you need to know:
If you are using either the Teflon or PTFE materials, rest assured
that they would distort in the process.
Certain materials are better not used for the design. For example,
thin materials or subs measuring less than 20 mils may not be ideal.
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
This is because of the difficulty in processing through planarization.
Besides, the material might be subject to tears or distortion.
The making of fine spaces or lines might not be possible. This is the
case when wrap plating is required. It is a plating method that
requires the termination of surfaces so they (the surfaces) could
have a buildup of copper.
How to Manufacture the Filled Vias
Whether you are using conductive or non-conductive via fills, the
processes often range from cleaning and preparation.
Here is a breakdown of the major steps that go into it:
1. Vias Drilling
You can choose between the laser beam and mechanical drilling methods
for the vias’ creation. You can determine the best vias’ drilling method
based on the number of circuit boards you want to produce, the costs and
the hole depth.
Talking about the holes, make sure that the right annular ring size is
created.
2. Clean the Vias
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
The drilling is followed by the cleaning process. The different cleaning
options you can use are:
Brush and Solvent: this combination helps to get rid of debris, while
paving the way for a smoother and finer drilling process.
You can also use a combination of chemical and abrasive
mechanical processes for the cleaning.
Irrespective of the cleaning method used, one point to note is that the
debris must be removed at all costs. Also, put the circuit board under
close scrutiny to ensure that there is an even plating of the copper within
the via’s holes.
3. Fill the Vias
Depending on what you want, you can choose to fill the vias with either
the conductive or non-conductive via fill.
The via filling processes for a PCB include the filling of the holes with
pressure and vacuum. This enables the excellent hole filling without giving
a way for gap formation in the resin. The other process is to clean the
panel’s surface. This process serves a dual purpose of getting rid of the
excessive resin and paving the way for planarization.
4. Planarize the Filled Vias
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
The planarization of filled vias refers to the mechanical-brushing process
of getting rid of resin. It also requires the smoothening and flattening of
the copper’s surface. This way, a uniform surface is achieved, while getting
rid of the excessive resin.
5. Over-Plating
This process comes after the planarization process is completed.
Over-plating the PCB with copper is an ideal way
of soldering the electronic components, accurately.
Request PCB Manufacturing & Assembly Quote Now
Before Filling the Vias
Note that despite the disparities between the conductive and
non-conductive filled vias’ processes; they also have some similarities and
differences, which we have discussed in this article.
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
Generally, the processes of filling the via holes are fraught with some
bottlenecks, which include:
Structure-related issues tend to come up.
There is a risk of filling up the via holes during the soldering process.
If this happens, it tends to render the entire process useless.
Another challenge is choosing between the conductive and
non-conductive via filling processes, based on the benefits they
offer.
Final Thoughts
For the best results, always contact a professional PCB designer to help
you navigate the hole drilling, soldering and filling process. Rayming
Technology helps you make a perfect choice on which of the conductive vs
non-conductive via fill PCB process is best for your circuits.
Related Posts:
1. Thermally conductive low loss laminate Taconic RF-35TC PCB
2. What’s the Difference between EMI EMS and EMC ?
3. How Small PCB can be manufactured ?
4. Xilinx XC9572XL-7PCG44I Technical Details
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
https://www.raypcb.com/conductive-vs-non-conductive-via-fill-pcb/
PCB Manufacturing & Assembly Services https://www.raypcb.com/
