BILL OF MATERIAL SKETCH LIST

N POS DESCRIPTION
NO
THK1 THK2 ASBL/ IDENT
DEST
DIAMETER QTY
PCS/MM
FABRICATION
1 Pipes (Length),ASME B36.19/B36.10,ASTM A312 S-40S S-40S 81 C1GXNDKX 3/4 461
The present document or drawing is property of Technip Italy S.p.a and shall not, under any circumstances, be totally or partially, directly or undirectly, transferred, reproduced, copied, disclosed or used, without its prior written consent,

Gr.TP316/316L + Sou,BE,Seamless,81
2 Eq Te,ASME B16.9,ASTM A403 Gr.WP316/316L + S-40S S-40S 81 C1GXPWVG 3/4X3/4 1
Sou,BW Ends,Seamless,81
3 WN Flg,ASME B16.5,ASTM A182 Gr.F316/316L + S-40S 81 C1GXTDK8 3/4 1
Sour,RF/BW End,150 Lbs,81
4 WN Flg,ASME B16.5,ASTM A182 Gr.F316/316L + S-40S 81/DR1 CV0TEFS 3/4 1
Sour,RF/BW End,300 Lbs,81/DR1
5 Gat BW,LP,API 602,ASTM A182 Gr.F316/316L,BW S-40S S-40S 81/DR1 C1CWJTG2 3/4 1
Ends,800 Lbs,81/DR1
CONT. ON ERECTION
STEM NORTH RA1-CH31004-0-01 6 SW Gk,ASME B16.20,RF as per ASME B16.5,Low 2/DR1 C1CVVTG8 3/4 1
E 840490 Stress,150 Lbs,2/DR1
1 N 420061 7 SW Gk,ASME B16.20,RF as per ASME B16.5,-,300 2/DR1 C6VY3ZA 3/4 1
FW EL.100739 Lbs,2/DR1
8 SBlt 2 HHx N,ASME B1.1/ASME B18.2.2,Full Length 2/DR1 CBT8U82D 5/8 4
2 28
Threaded,2/DR1 - 80 mm Length
3/4X3/4"NS 9 SBlt 2 HHx N,ASME B1.1/ASME B18.2.2,Full Length 2/DR1 CBT8U814 1/2 4
E 840490 28 Threaded,2/DR1 - 70 mm Length
4
10 Bld Flg,ASME B16.5,ASTM A182 Gr.F316/316L + 2/DR1 CY9KSUA 3/4 1

147
Sour,RF,300 Lbs,2/DR1
1

2
5
Change this joint W.Cat from A to F
542 10 STEM NORTH
because no fitting
Rework code:6b 1
"NS F4 G7 B8
3/4 DR1
Class 300 RF
for any purpose and in any way other than that for which it is specifically furnished or outside the extent of the agreed upon right of use.

3
3
RA1-CH31018-0-01-SP001
FW
2 CONN. TO
31PK-11
Nozzle:TP-003
0.75 in RFFE#150 F3 G6 B9
E 839947
N 420061
EL.100711

TOTAL NUMBER OF SPOOLS: 1

SUPPORT SYMBOLOGY
COM STD or SPC support common
to more than one line Y
e.g.: line support
PRF
STD or SPC support welded to pipe at
workshop during pipe spools prefabrication Z X
MRS INPUT AND OUTPUT
Itemized Piping Supports DATA FOR PIPELINE
For Itemized Piping Supports refer to Material Requisition 072744C-000-MR-1383-001 EFFORT ANALYSIS
SPC ARE BASED ON
S- Special Piping Support SYSTEM OF
Refer to supp. dwgs collection 072744C-000-DW-1360-001 COORDINATES AS
STD IN THE DRAWING
Standard Piping Support
Refer to supp. dwgs collection 072744C-000-STC-1390-000

SPOOL ID.
SINGAPORE EXPANSION PROJECT
1) ALL DIMENSIONS ARE IN MILLIMITRES REFERENCE 1) CONSTRUCTION LINE LIST: 072744C-031 -NM-1300-012 5) CONSTRUCTION SPECIFICATION FOR PIPING PREFABRICATION, ERECTION N WELD
ISOMETRIC ID. RA1-CH-31018-0-01 LINE No. CH31018-0-1M1N-NT-N UNIT
2) PIPING INSULATION/PAINTING SUMMARY: 072744C-000-MTO-XXXX-01 AND NON DESTRUCTIVE EXAMINATION: 072744C-000-MS-1320-51

SYMBOLOGY
2) DIMENSIONS AND LAYOUT OF SOCKET WELDED AND THREADED LINES ARE INDICATIVE ONLY AND SHALL BE DOCUMENTS N FIELD WELD
NOTES CHECKED AT JOB SITE BEFORE ERECTION FOR DESIGN 3) TECHNICAL PIPING SPECIFICATION AND CLASSES: 072744C-000-JSD-1300-001 6) FOR STRESS ANALYSIS "FLEXIBILITY LEVELS" AND STRESS TRACED
CONDITION 4) TECHNICAL SPECIFICATION FOR PIPING PREFABRICATION AND ERECTION: ANALYSIS CALCULATIONS NUMBERS REFER TO DOC.: 31
3) ISOMETRIC SKETCHES PREVAIL ON 2D AREA DRAWINGS SUPPORT
072744C-000-MS-1310-001;072744C-000-MS-1320-001;072744C-300-MS-1320-001 072744C-000-NM-1370-001 POSITION
PROJ. AREA TYPE SERVICE SEQUENCE N. SUBLINE SHEET OF REV
2 30/04/2021 IFC-REVISED AS SHOWN ZXU AO 1 29/01/2021 ISSUED FOR CONSTRUCTION ZXU AO 0 30/10/2020 ISSUED FOR CONSTRUCTION ZXU AO TFMC NO. 072744C RA1 DW CH 31018-0
REV DATE DESCRIPTION STRESS APPR. REV DATE DESCRIPTION STRESS APPR. REV DATE DESCRIPTION STRESS APPR. NESTE NO. 2308 RA1 DW CH 31018-0
01 01 01 2
Technip Italy S.p.a - 00148 ROMA - Viale Castello della Magliana, 68