EDULABS DIDACTIC

ANALOG LAB TRAINER

ALT-300

INSTRUCTION MANUAL
ALT-300 Instruction Manual

Table Of Contents

SECTION TITLE PAGE

1 Introduction 2
2 Features 2
3 Preparation for Use 2
3-1 Unpacking and Contents Check 2
3-2 Pre-Operation Procedure 3
3-3 First Operation 3
4 Controls and Indicators 4
5 Specifications, Operation, Pre-Operation, Applications 5
5-1 Power Switch 6
5-2 DC Power Supplies 6
5-3 Analog Ammeter Display 8
5-4 Analog Voltmeter Display 8
5-5 6 Ways Rotary Switches 9
5-6 Function Generator 9
5-7 Potentiometer 10
5-8 Speaker 11
5-9 Two Position Slide Switches 12
5-10 Three Position Slide Switches 12
5-11 AC Power Supplies 13
5-12 4mm Adaptor 13
5-13 BNC Adaptors 14
6 Maintenance 15
6-1 Fuse Replacement 15
6-2 Cleaning 15
7 Technical Documentation 16
7-1 Circuit Diagrams 16
8 Warranty and Standard Conditions of Sale 19

EDULABS DIDACTIC 1 www.scienscope.com.my

ALT-300 Instruction Manual

S EC T I ON 1 : IN T R OD U C TI ON

The ALT-300 ANALOG LAB TRAINER is an ideal teaching aid for all types of electronic circuits. There are variety of
functional input and output circuits (see Features) which can be used to stimulate or measure electrical signals from the
circuit under test or development. These circuit functions allow for the testing of circuits without the need for many
expensive individual pieces of equipment.

SECTION 2 : FEATURES

• Completely Self-Contained Unit

• DC Power Supplies
• AC Power Supplies
• DC Power Supplies: Fixed : +5V/0.5A, -5V/0.5A, +12V/0.5A, -12V/0.5A, Variable : +/-0V to +/-20V, 0.5A
• Analog Ammeter Display
• Analog Voltmeter Display
• 1 Channels Function Generator with Sine, Triangle and Square Wave Outputs with selection frequency from
10 Hz to 500KHz in 6 decades.
• 1 Channels Clock Generator with fine adjust TTL Clock output 1 Hz to 500KHz in 6 decades.
• Potentiometer 1KΩ & 100KΩ
• Three Position Slide Switches
• Two Position Slide Switches
• 2 Numbers BNC Socket to Turn Pin Header Adaptors
• Speaker, 8Ω, 0.25W with Buffer
• 5 Numbers 4mm & 8 Numbers 2mm Sockets to Turn Pin Header Adaptors
• 1680 tie points Breadboard

SECTION 3 : PREPARATION FOR USE

3-1 : Unpacking and Contents Check

The ALT-300 comes complete and ready to use. Check the following components list when unpacking. If any pieces
are missing, immediately notify the distributor you purchased the instrument from.

1. ALT-300 Analog Lab Trainer

2. AC Power Cable
3. Instructions Manual

3-2 : Pre-Operation Procedure

Inspect the ALT-300 for any signs of damage. Make sure that the power cord is for your voltage 240 VAC.
Allowable input voltages are as follows:

240VAC : 240 VAC @ 50Hz, ±10%

EDULABS DIDACTIC 2 www.scienscope.com.my

ALT-300 Instruction Manual

CAUTION
Should the ALT-300 ANALOG LAB TRAINER fail to operate after applying AC power check the fuse located
on the back panel. Replace with the same type and style fuse of 3A, 240V or equal specifications.

WARNING

READ AND UNDERSTAND THIS MANUAL

BEFORE USING THE INSTRUMENT.
Failure to understand and comply with the
WARNINGS and operating instructions can result
in serious or fatal injuries and/or property damage

3-3 : First Operation

It is recommended that during the first operation of the ALT-300 the Pre-Operation checks are performed as per
section 3. These checks will help to verify the proper operation of the ALT-300 ANALOG LAB TRAINER. These checks
can also be made at any time in the future as a partial performance test.

EDULABS DIDACTIC 3 www.scienscope.com.my

ALT-300 Instruction Manual

SECTION 4 : CONTROLS AND INDICATORS

16 15 14

13
1

2
12

3 11

7 8 17 4 10

EDULABS DIDACTIC 4 www.scienscope.com.my

ALT-300 Instruction Manual

Index
Control or Indicator Function
No.
1 Power Switch Provide the On/Off switching of incoming power.
Supplies Six DC power supplies as follows
+5V & -5V @ 0.5A max
+12V & -12V @ 0.5A max
2 DC Power Supply
+V (+0V ~ +23Vdc) @ 0.5A max
-V (-0V ~ -23Vdc) @ 0.5A max

Selects the range of the frequency in times 10 increments for

Function Generator & Clock Generator. Switch Position Range
x 10 1 Hz - l0 Hz
x 100 10 Hz - 100 Hz
3 Frequency Range Switch
x 1k l00 Hz - 1 kHz
x 10k 1 kHz - l0 kHz
x l00k 10 kHz - l00 kHz
x 1M 100 kHz – 500kHz
4 Waveform Selection Select Waveform for Square, Triangle and Sine wave
Adjusts the variable frequency of the function generator & Clock
5 Frequency Control
based upon the Frequency Range Switch setting
6 Amplitude Control Adjusts the amplitude of the Function Generator Waveform
Variable Resistor 1KΩ
7 Potentiometers
Variable Resistor 100KΩ
Slide Position (If slide up then “ON” the pin com & 1 is connect,
8 Three Position Slide Switches
and vice versa)
Toggle Position (If slide up then “ON” the Pin com & 1 is
9 Two Position Slide Switches
connect, and vice versa)
10 BNC Adaptors Provides 2 numbers BNC Socket to turn pin headers
11 4mm Adaptor Provides 5 numbers 4mm socket to turn pin headers
12 AC Power Supplies Provides two 15VAC, two 9VAC and Ground
13 Speaker 8 Ohm/0.25W Speaker with buffer
0 - 5ADC full scale
14 Analog Ammeter Display
Class 1.5
0 - 50V DC full scale
15 Analog Voltmeter Display
Class 1.5
16 6 Ways Rotary Switches 2 pole 6 Way Rotary Switches
Interconnected nickel plated with a total of 1680 tie points in total,
17 Breadboard fitted all DIP sizes and components with lead and solid wire in
diameter of AWG #22-30 (0.3 - 0.8mm)

EDULABS DIDACTIC 5 www.scienscope.com.my

ALT-300 Instruction Manual

SECTION 5 : SPECIFICATIONS, OPERATION, PRE-OPERATION AND APPLICATIONS

The following section covers the above four topics grouped for each function. The pre-operation procedures,
when provided are to verify that functional circuits are operating and to help gain familiarity with the equipment features.
Refer to section 4 for all ALT-300 controls, indicators and functions when performing the pre-operation checks.

5-1 : Power Switch

Figure 1

The main power switch controls the power source for the whole trainer. The trainer will only get the power source
when the power switch has been turned on, and the light on the switch is on.

5-2 : DC Power Supplies

Figure 2
5-2.1 : Variable Supplies

Specifications:
Output Voltage: +0V to +25V, -0V to -25V
Output Current: 0.5A max
Line Regulation: < 1% @ 0 - 25Vdc
Load Regulation: < 30mV @ 0 – 0.5 A

EDULABS DIDACTIC 6 www.scienscope.com.my

ALT-300 Instruction Manual

Operation:
The two independent variable power supply outputs are connected between the "+V and GND" and also
the "-V and GND". Each output is controlled individually by the "+V" and "-V" controls.

Application:
The variable power supply outputs can be used to power different linear devices such as operational
amplifiers and TTL, CMOS, and compatible logic devices.

5-2.2 : +5 Vdc Supply

Specifications:
Output Voltage: +5 ± 0.25 Vdc
Output Current: 0.5A max

5-2.3 : -5Vdc Supply

Specifications:
Output Voltage: -5 ± 0.25 Vdc
Output Current: 0.5A max

Application:
The +5 and -5 power supplies can be used as the source power of logic circuits such as TTL or CMOS.

5-2.4 : +12 Vdc Supply

Specifications:
Output Voltage: +12 ± 0.25 Vdc
Output Current: 0.5A max

5-2.5 : -12Vdc Supply

Specifications:
Output Voltage: -12 ± 0.25 Vdc
Output Current: 0.5A max

Application:
The +12 and -12 power supplies can be used as the source power of logic circuits such as TTL or CMOS.

EDULABS DIDACTIC 7 www.scienscope.com.my

ALT-300 Instruction Manual

5-3 : Analog Ammeter Display

Figure 3
Specifications:

0 - 5ADC full scale

Class 1.5

5-4 : Analog Voltmeter Display

Figure 4
Specifications:

0 - 50V DC full scale

Class 1.5

Operation:

- Plug in wire positive supply “+V” from DC Power Supply to “+” pin connection DCV Meter, then GND to
“-“pin connection DCV Meter.

EDULABS DIDACTIC 8 www.scienscope.com.my

ALT-300 Instruction Manual

5-5 : 6 Way Rotary Switches

Figure 5
Specifications:

2 pole 6 Way Rotary Switches

5-6 : Function Generator

Figure 6
Specifications:
Frequency Ranges: 1 Hz to 10 Hz
10 Hz to 100 Hz
100 Hz to 1 kHz
EDULABS DIDACTIC 9 www.scienscope.com.my
ALT-300 Instruction Manual
1 kHz to 10 kHz
10 kHz to 100 kHz
100 kHz to 500 kHz

The output frequency is continuously variable between these ranges by adjusting the variable frequency control
knob.
The amplitude is variable for the sine wave, triangle and square wave by adjusting the amplitude control knob.

Sine Wave : 0 to 20Vp-p

20Vp-p
Variable

Triangle wave : 0 to 10p-p

10Vp-p
Variable

Square wave : 0 to 22Vp-p

22Vp-p
Variable

Figure 7

Operation:
The output of each function is made at the terminals as shown in Fig 4. All outputs are available simultaneously at
the same frequency. Select the frequency range and then fine tune the frequency using the Variable Frequency
Control Knob. Adjust the amplitude of the sine, triangle and Square wave using the Amplitude control.

Pre-Operation Check:
The output of the function generator can be observed by using an oscilloscope. Connect the outputs to the
oscilloscope being certain to connect GND to GND between the Oscilloscope and ALT-300. The GND on the
ALT-300 is common with the AC Power ground connection. Most oscilloscopes also have their input ground pin
common with the AC power ground of the oscilloscope. Please make sure that the grounds are connected properly.

Application:
The function generator can be used to generate input stimuli waveforms for all types of digital and analog circuits.
It should be noted however that for triggering TTL and compatible gates the negative portion of the square wave
should be removed. This can be accomplished by using a comparator or clipping circuit.

5-7 : Potentiometer

Figure 8

EDULABS DIDACTIC 10 www.scienscope.com.my

ALT-300 Instruction Manual

Specifications:

Variable Resistor VR1: 1KΩ

Variable Resistor VR2: 100KΩ

5-8 : Speaker

Figure 9
Specifications:

Input Impedance: 8 ohms

Power: 0.25 watt

Operation:
Connect the signal to the input market "+" and "-" speaker input. The input should not exceed 0.25 watt. (V less
than 2.83 Vrms, 4 Vpeak, or 8 Vp-p)

Pre-Operation Check:
1. Connect the "~" sine function generator output to the "+" speaker input.
2. Connect the GND of the function generator to the "-" speaker input.
3. Set the frequency range switch to the "X100" position and slowly increase the amplitude control until the
speaker sounds.

Application:
For exercising the audio experiment, use the speaker as the output load. When there has some
Response, sound can be heard from the speaker.

EDULABS DIDACTIC 11 www.scienscope.com.my

ALT-300 Instruction Manual

5-9 : Two Position Slide Switches

Figure 10
Specification:

Consist of two 3 Pin Slide Switch (ON-OFF).

Operation :

Toggle Position
- When slide up then the pin COM & 1 is connected (ON) and vice versa.
- When slide down then the pin COM & 2 is connected (ON) and vice versa

5-10 : Three Position Slide Switch

Figure 11
Specification:

Consist of two 8 Pin Slide Switch (ON-OFF-ON).

Operation :

Slide Position
- When slide up then the pin COM & 1 is connected (ON) and vice versa,
- When slide middle then the pin COM & 2 is connected (ON) and vice versa,
- When slide down then the pin COM & 3 is connected (ON) and vice versa.
EDULABS DIDACTIC 12 www.scienscope.com.my
ALT-300 Instruction Manual

5-11 : AC Power Supplies

Figure 12
Specification:

Consist of two 19V, two 15VAC, two 9VAC & 0V (Ground) outputs.

Operation:

Connect one of the outputs to one of the 15V/9V point and another output to one of the point 0V.

5-12 : 4mm Adaptor Interface

EDULABS DIDACTIC 13 www.scienscope.com.my

ALT-300 Instruction Manual

Figure 13

Specification:

The 4mm adaptor consists of four sockets (4mm size) where the outputs for each sockets connected directly to 4
numbers of turn pins.

5-13 : BNC Adaptor Interface

Figure 14

Specification:

The BNC adaptor consists of two sockets where the outputs for each sockets connected directly to 4 numbers of
turn pins.

EDULABS DIDACTIC 14 www.scienscope.com.my

ALT-300 Instruction Manual

SECTION 6 : MAINTANANCE

WARNING
Remove power prior for performing maintenance on equipment. Failure to do so can cause serious
injury to personnel.

Maintenance consists of fuse replacement, calibration adjustment procedures, and periodic cleaning. Performing the
calibration and adjustment procedures only by Authorized Service Engineer, otherwise the warranty will void.

CAUTION
The following procedures should only be performed by persons trained and qualified in electronics and
electronic equipment service. Do not attempt these procedures if not qualified.

6-1 : Fuse Replacement

1) Ensure AC power is disconnected from equipment.

2) Turn to back of ALT-300 and locate the fuse package.

3) Open the fuse cover and remove the dysfunction fuse.

4) Replace with the same type and style fuse of 3A, 250V or equal specifications.

6-2 : Cleaning

The ALT-300 can be cleaned with a dry, soft cloth to remove any oil, grease, or grime from the equipment.
Never use liquid solvents or detergents. If the equipment got wet for any reason, dry using low pressure air (less
than 25 PSI). Use care and caution around areas where water or air could enter the interior of the equipment while
drying.

EDULABS DIDACTIC 15 www.scienscope.com.my

ALT-300 Instruction Manual

SECTION 7: TECHNICAL DOCUMENTATION

7-1 : Circuit Diagrams

7-1-1 : Power Supplies (+5VDC & -5VDC)

7-1-2 : Power Supplies (+12VDC & -12VDC)

EDULABS DIDACTIC 16 www.scienscope.com.my

ALT-300 Instruction Manual

7-1-3 : Power Supplies (0 ~ +25VDC & 0 ~ -25VDC)

EDULABS DIDACTIC 17 www.scienscope.com.my

ALT-300 Instruction Manual

7-1-4 : Function & Clock Generator 1

EDULABS DIDACTIC 18 www.scienscope.com.my

ALT-300 Instruction Manual

SECTION 8: WARRANTY AND STANDARD CONDITIONS OF SALE

The Seller warrants to the Purchaser that any equipment manufactured by it and bearing its name plate to be free from
defects in material or workmanship, under proper and normal use and service, as follows: If, at any time within one (1)
year from the date of shipment, the Purchaser notifies the Seller that in his opinion, the equipment is defective, and returns
the equipment to the Seller’s originating factory prepaid, and the Sellers inspection finds the equipment to be defective in
material or workmanship except part like switches, knob, push button, lighting, etc. the Seller will promptly correct it
by either, at its option, repairing any defective part or material or replacing it free of charge and return shipping lowest
cost transportation prepaid by purchaser (if Purchaser requests premium transportation, Purchaser will be billed for
difference in transportation costs). If inspection by the Seller does not disclose any defect in material or workmanship, the
Seller’s regular charges will apply. This warranty shall be effective only if use and maintenance is in accordance with
Seller's instructions and written notice of a defect is given to the Seller within such period. THIS WARRANTY IS
EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTIES, WRITTEN, ORAL OR IMPLIED.
SPECIFICALLY, WITHOUT LIMITATION, THERE IS NO WARRANTY OF MERCHANTABILITY OR
FITNESS FOR ANY PURPOSE. The liability of the Seller shall be limited to the repair or replacement of materials or
parts as above set forth.

LIMITATION OF LIABILITY

The Seller shall not be liable for any claim or consequential or special loss or damage arising or alleged to have arisen
from any delay in delivery or malfunction or failure of the equipment. The Seller’s liability for any other loss or damage
arising out of or connected with the manufacture or use of the equipment sold, including damage due to negligence, shall
not in any event exceed the price of the equipment supplied by Seller.

GENERAL CONDITIONS

All orders are subject to acceptance by Seller at its Main Office. Stenographic and clerical errors are subject to correction.
No oral or subsequent modification or any other foregoing general provisions or of any term or condition of any order
shall be binding unless agreed to in writing by the Seller and Purchaser.

SCIENSCOPE SDN BHD reserves the right to make changes at any time, without notice, in prices, colors, materials,
specifications and models, and also to discontinue models.

SCIENSCOPE SDN BHD

(Company No : 520887-D)
20, Jalan BP 5/10, Bandar Bukit Puchong,
47100 Puchong, Selangor Darul Ehsan.
Tel : 6012-4080443
E-mail : [email protected]
Website : http://www.scienscope.com.my

Solution provider for scientific and technical education training system since 2000

EDULABS DIDACTIC 19 www.scienscope.com.my