! " #  $%
&'()$ $*+'  $
Legal notice:

The information presented is subject to change without notice.

ALE International assumes no responsibility for inaccuracies contained

herein.

Copyright © ALE International, 2016

Disclaimer:

While efforts were made to verify the completeness and accuracy of the
information contained in this documentation, this document is provided “as
is”. To get more accurate content concerning Cross Compatibilities, Product
Limits, Software Policy and Feature Lists, please refer to the accurate
documents published on the Business Partner Web Site.

In the interest of continued product development, ALE International reserves

the right to make improvements to this documentation and the products it
describes at any time, without notice or obligation.

The CE mark indicates that this product conforms to the following Council
Directives:
- 2014/53/EU for radio equipment
- 2014/35/EU and 2014/30/EU for non radio equipment (including wired
Telecom Terminal Equipment)
- 2014/34/EU for ATEX equipment
- 2011/65/EU (RoHS)
  
        
        

Chapter 1
Expert Documentation structure

Chapter 2
C, S, M, L Racks

 Hardware description ............................................................................ 10

 OXO Connect Compact .................................................................................. 10
 OXO Connect S .............................................................................................. 10
 OXO Connect M and OXO Connect L ............................................................ 11

Chapter 3
Boards

 PowerCPU EE ........................................................................................... 13

 Hardware description ...................................................................................... 13
 Hardware configuration .................................................................................. 14
 External connections ...................................................................................... 16
 PowerMEX .................................................................................................. 20

 !"#!$% & '#! & ( ) "#!* &             3/160
  
              

 Hardware description ...................................................................................... 21

 Hardware configuration .................................................................................. 21
 External connections ...................................................................................... 22
 BRA .............................................................................................................. 22
 Hardware description ...................................................................................... 22
 External connections ...................................................................................... 23
 PRA .............................................................................................................. 26
 Hardware description ...................................................................................... 26
 Hardware configuration .................................................................................. 27
 External connections ...................................................................................... 28
 MIX-2 ............................................................................................................ 29
  Hardware description ...................................................................................... 29
  External connections ...................................................................................... 30
 Mini-MIX ...................................................................................................... 31
 AMIX-1 ......................................................................................................... 34
  Hardware description ...................................................................................... 34
  External connections ...................................................................................... 34
 UAI ................................................................................................................ 35
  Hardware description ...................................................................................... 36
  External connections ...................................................................................... 39
 SLI-2 ............................................................................................................. 40
  Hardware description ...................................................................................... 40
  External connections ...................................................................................... 41
 LanX-2 ......................................................................................................... 42
  Hardware description ...................................................................................... 43
  Configuration examples .................................................................................. 43
  External connections ...................................................................................... 44
 APA .............................................................................................................. 46
 Hardware description ...................................................................................... 46
 External connections ...................................................................................... 47
 Power Supplies ........................................................................................ 49
 Hardware description ...................................................................................... 49

4/160  !"#!$% & '#! & ( ) "#!* &            
  
               

Chapter 4
Dedicated Sets

 8001/8001G Deskphones ...................................................................... 56

 8001/8001G Deskphone description .............................................................. 56
 8001/8001G Deskphone Commissioning ....................................................... 58
 8018 DeskPhone ...................................................................................... 60
 Detailed description ........................................................................................ 60
 Commissioning ............................................................................................... 63
 8028/8038/8068 Premium DeskPhones ............................................ 64
 Detailed description ........................................................................................ 64
 Commissioning ............................................................................................... 71
 Maintenance for 80x8 ..................................................................................... 75
 8082 My IC Phone .................................................................................... 76
 Basic description ............................................................................................ 76
 Hardware description ...................................................................................... 79
 Commissioning ............................................................................................... 83
 Reset to factory .............................................................................................. 94
 4135 IP Conference Phone ................................................................... 96
  Basic description ............................................................................................ 96
  Hardware description ...................................................................................... 97
  Commissioning ............................................................................................... 99
 Generic SIP Phones ............................................................................. 105
 Commissioning ............................................................................................. 105
 4018 Phone Extended Edition ........................................................... 107
  Basic description .......................................................................................... 108
  Hardware description .................................................................................... 108
  Commissioning ............................................................................................. 112
  Maintenance ................................................................................................. 117
 8029/8039 Premium Deskphones .................................................... 119
  Detailed description ...................................................................................... 120
  Commissioning ............................................................................................. 125

 !"#!$% & '#! & ( ) "#!* &             5/160
  
              

 4019 Digital Phone ................................................................................ 126

  Basic description .......................................................................................... 126
  Hardware description .................................................................................... 127
  Commissioning ............................................................................................. 131
 Input Method Editor .............................................................................. 132
  Operation ...................................................................................................... 132
 Terminal downloading ......................................................................... 137
 Operation ...................................................................................................... 137
 Add-on Module ....................................................................................... 139
 LEDs and icons on AOM modules ................................................................ 139
 V24/CTI Interface Module ................................................................... 140
 Hardware description .................................................................................... 140
 AP Interface Module ............................................................................. 142
 Hardware description .................................................................................... 142
 S0 Interface Module .............................................................................. 143
  Hardware description .................................................................................... 143
 500 DECT Handset ................................................................................ 145
 Hardware description .................................................................................... 145
 8212/8232/8242/8262 DECT ................................................................ 151
  Overview ....................................................................................................... 151
  Key benefits .................................................................................................. 153
  Key features ................................................................................................. 154
  Location ........................................................................................................ 154
  Technical specifications ................................................................................ 154
  Accessories .................................................................................................. 159
 PIMphony Reflexes ............................................................................... 159
  Detailed description ...................................................................................... 159

6/160  !"#!$% & '#! & ( ) "#!* &            
  
   

        

The OXO Connect Expert Documentation is split into fifteen separated documents. Each
document only describes the features supported by OXO Connect RC2.0* (for example: MMC
station is not described since it is not supported). Please refer to the OXO Connect
Documentation Note, for historical information. In addition, the Cross Compatibility document
is the reference for detailed status about supported and unsupported devices and applications.
* RC2.0 stands for any release starting from 2016 introducing Connect capabilities.
It appears on:
- Product stickers with release format: RC020/xx.yy
- In any documentation (including this one) as: R2.0
These documents are:
table 1.1: Expert Documentation structure
Documentation title Part number
[1] OXO Connect Expert Documentation: General Presentation 8AL91200xxxx
Summary: this document contains general information on the
OXO Connect, such as a brief description of services provided,
platform hardware, handsets and user applications available, lim-
its, compatibility with standards, environmental constraints.
[2] OXO Connect Expert Documentation: Hardware: Platform, inter- 8AL91201xxxx
faces and devices
Summary: this document covers all hardware aspects related to
the OXO Connect: this includes description of platforms (racks),
boards, sets and complementary equipment such as additional
modules or interface modules. This document also contains com-
missioning procedures for sets.
[3] OXO Connect Expert Documentation: User services 8AL91202xxxx
Summary: this document gives the presentation and configuration
procedure of features available for end-users. The final chapter of
the document synthesizes features availability according to the
type of device or application.
[4] OXO Connect Expert Documentation: Voice mail 8AL91203xxxx
Summary: this document details the integrated voice mail system
and automated attendant (general description, management, ser-
vices available for end-users), as well as configuration procedure
to connect an external voice mail unit.
[5] OXO Connect Expert Documentation: Mobility 8AL91204xxxx
Summary: this document contains a detailed description of mobil-
ity services available on the OXO Connect. This includes useful
information to deploy a DECT, PWT or IP-DECT infrastructure,
the description of associated base stations and handsets, and ne-
cessary information to implement OpenTouch Conversation cli-
ents.
Note 1:
This document does not cover VoWLAN.

 !"#!$% & '#! & ( ) "#!* &             7/160
  
Chapter 1        

Documentation title Part number

[6] OXO Connect Expert Documentation: VoIP services 8AL91205xxxx
Summary: this document describes VoIP protocols supported by
the OXO Connect (such as H.323, SIP), configuration procedure
of private or public access through IP links, as well as dimension-
ing and maintenance basic information.
[7] OXO Connect Expert Documentation: Private networks 8AL91206xxxx
Summary: this documentation gives a description of architectures
and protocols (such as SVPN, QSIG) supported for a private net-
work, a description of ARS, metering, clock synchronization, and
the configuration procedure of accesses.
[8] OXO Connect Expert Documentation: General applications 8AL91207xxxx
This document gives a description of various applications avail-
able on the OXO Connect, such as Hotel, Call metering, CTI,
doorphones, Network management center, point-to-point/point to
multipoint T0, permanent logical link, multiple automated attend-
ant, multiple entities, My IC Plugin for Outlook®, My IC Web,
PIMphony Touch.
[9] OXO Connect Expert Documentation: Web-based tool 8AL91208xxxx
Summary: this document describes the web-based tool, which is
the integrated monitoring tool of the OXO Connect.
[10] OXO Connect Expert Documentation: OmniTouch Call Center Of- 8AL91209xxxx
fice
Summary: this document provides the description and installation
procedure of OmniTouch Call Center Office. The document also
includes presentation and operation of Announcement, Traceabil-
ity, and a short description of Agent, Statistics and Supervisor ap-
plications.
[11] OXO Connect Expert Documentation: Management tools 8AL91210xxxx
Summary: this document describes the management tool avail-
able for OXO Connect(OMC). The document describes the OMC
installation procedure, the different types of access between OMC
and OXO Connect (local, remote, with or without proxy), the OXO
Connect software installation procedure via OMC and the list of
services that can be managed by OMC.
[12] OXO Connect Expert Documentation: Maintenance services 8AL91211xxxx
Summary: this document contains basic information concerning
the maintenance of your OXO Connect. This includes a diagnosis
methodology in case of system of terminal(s) failure, the list of
system messages, procedure to save/restore data, procedure to
stop/restart your system, to replace CPU, boards and sets.
[13] OXO Connect Expert Documentation: Security 8AL91212xxxx
Summary: this document gives essential information to secure
your OXO Connect. This includes deployment guide for certificate,
management of passwords, management of accesses to services
from LAN/WAN and network configuration for remote accesses,

8/160  !"#!$% & '#! & ( ) "#!* &            
  
        

Documentation title Part number

[14] OXO Connect Expert Documentation: System services 8AL91213xxxx
Summary: this document gives information about software keys,
including their complete list. The document also describes opera-
tion of the OXO Connect with NTP (as client or server) and the
configuration of the embedded DHCP server.
[15] OXO Connect Glossary 8AL91214xxxx
Summary: this document contains a glossary of general telecom-
munications terms as well as specific terms related to OXO Con-
nect.

In the present document, cross-references are identified by the number in the first column of
the above table.
Part numbers are given in the last column, where xx corresponds to the language code of the
document.
Outlook is either a registered trademark, or a trademark of Microsoft Corporation in the United
States and/or other countries.

 !"#!$% & '#! & ( ) "#!* &             9/160
  
   

      

2.1 Hardware description

2.1.1 OXO Connect Compact

The OXO Connect Compact platform is a wall-mounted version. It provides 2 slots (1xCPU
slot+1xMIX slot).
The OXO Connect Compact platform is not expandable and cannot be used as satellite.
___change-begin___
___change-end___
The Mini-MIX daughter board which is plugged into the PowerCPU EE board provides two Z
(Analog Extension) ports and two T0 (ISDN Basic Rate) accesses.

2.1.2 OXO Connect S

The OXO Connect S mainly consists of a plastic frame.
The plastic frame receives all the parts for attaching the power supply board, the fans, the
battery and the mains power connector, and everything needed to facilitate the routing of the
cables.

10/160  !"#!$% & '#! & ( ) "#!* &            
  
 + % ,  - .

There is no backplane board: the metric connectors are on the power supply module.
The enclosure consists of 3 parts: metal cover and base, plastic front face.
Access to the fans, the power supply module and the battery is gained by disconnecting the
mains cable and removing the top metal cover (it is vital to remove all the boards before
opening the cover).

2.1.3 OXO Connect M and OXO Connect L

The frame consists of a "U"-shaped sheath closed on the top by a riveted plate. The boards
are guided by 2 rails for OXO Connect M, or 3 rails for OXO Connect L, riveted vertically to the
frame.
The enclosure consists of a metal top part, two metal side parts and a plastic front face.
Access to the fans, the power supply module and the batteries is gained by disconnecting the
power cable and unscrewing the backplane.

 !"#!$% & '#! & ( ) "#!* &             11/160
  
Chapter 2 + % ,  - .

12/160  !"#!$% & '#! & ( ) "#!* &            
  
   

  

3.1 PowerCPU EE

3.1.1 Hardware description

3.1.1.1 Overview
The PowerCPU EE board, based on processor PowerQuicc II Pro MPC8377 from Freescale,
has the following characteristics: 800 MHz processor, 512 MB DDR2 SDRAM, MSDB (Mass
Storage Daughter Board) 8 GB equipped with eMMC (embedded Multi-Media Card), VoIP
DSP C6421/4 (16 VoIP channels).
The PowerCPU EE board is built around 2 main blocks interconnected via PCI:
- CPU part with MPC8377 processor and following interfaces:
• DDR 2 memory
• BOOT (NOR Flash)
• Dual UART
• PCI
• LAN interfaces
• I2C
- Telecom part with INOX ASIC and with connections to:
• Telecom DSP0 TMS320C5507
• Modem DSP1 TMS320C5402
• VoIP DSP TMS320C6421 (16 VoIP channels)
• Legacy Telecom architecture (PCM buses, ASL, HSL)
3.1.1.2 Daughter Boards
The PowerCPU EE board can be equipped with the following daughter boards:
- AFU-1 (Auxiliary Function Unit): supporting auxiliary functions such as general bell,
doorphone, audio In, audio Out, etc. The AFU-1 board is required for the connection of the
ISDN-EFM box (T0/S0 forwarding)
- HSL (High Speed Link): module interconnections. This daughter board is not compatible
with the Mini-Mix daughter board.
- MSDB (Mass Storage Daughter Board) 8 GB equipped with eMMC (embedded
Multi-Media Card): memory extension.
- ARMADA VoIP32: supporting two additional VoIP DSPs TMS320C6421 (2x16 VoIP
channels)
- ARMADA VoIP64: supporting two additional VoIP DSPs TMS320C6424 (44 VoIP
channels)
- Mini-MIX (only for OXO Connect Compact): this daughter board provides two Z (analog)
ports and two T0 accesses. This daughter board is not compatible with an HSL board.
___change-begin___
 !"#!$% & '#! & ( ) "#!* &             13/160
  
Chapter 3 / 

___change-end___
Figure 3.1: Example of Daughter Boards on PowerCPU EE

3.1.2 Hardware configuration

3.1.2.1 Meaning of the LED Indications
___change-begin___
___change-end___
Figure 3.2: PowerCPU EE Front Panel

Name Color Function

CPU Green CPU functioning LED (flashing)

14/160  !"#!$% & '#! & ( ) "#!* &            
  
 / 

Name Color Function

POWER Red/Green - Mains operation: steady green LED
- Battery operation: steady yellow LED
- Idle: flashing red LED
- System shut down: steady red LED
FAN Red/Green - Both fans functioning: steady green LED
- 1 or both fans down: steady red LED
LAN Green LAN functioning LED (flashes when there is traffic)
Mini-MIX Green (only on OXO Green only when accepted by the license 2B channels for MIX-
Connect Compact plat- 2 boards. Detection of Mini-MIX board in OXO Connect Com-
form) pact platform.
MODULE Green Presence of HSL board

3.1.2.2 General Connection Diagram

___change-begin___
___change-end___
 !"#!$% & '#! & ( ) "#!* &             15/160
  
Chapter 3 / 

3.1.3 External connections

3.1.3.1 Output Ports
___change-begin___
___change-end___
Figure 3.4: PowerCPU EE
Available functions:
- LAN: 10/100/1000 base T Ethernet port (MDI-II/straight).
- SLI1/SLI2: Analog Z accesses from Mini-MIX board, General ringer; 12V output
- AUX: General ringer; 12V output
- CONFIG: RS232 for OMC.
- MODULE1: HSL1 link of HSL board for connection to module expansion 1
- ISDN T01: ISDN T01 port of Mini-MIX board
- MODULE2: HSL2 link of HSL board for connection to module expansion 2
- ISDN T02: ISDN T02 port of Mini-MIX board
- AUDIO: Interfaces Please wait message, Background music, Loudspeaker, Alarm
- DOORPHONE: Interfaces doorphone
table 3.2: Socket Connections
RJ45 pin 1 2 3 4 5 6 7 8
LAN TX+ TX- RX+ RX-
CenRG
SLI1/SLI2 Ground +12 V CenRg A ZA1 ZB1 ZA2 ZB2
B
CenRG
AUX Ground +12 V CenRg A
B
CONFIG CTS RX RMTRES Ground TX DTR RTS
MODULE1 TX+ TX- RX+ RX-
ISDN T01 TX+ RX+ RX- TX-
MODULE2 TX+ TX- RX+ RX-

16/160  !"#!$% & '#! & ( ) "#!* &            
  
 / 

ISDN T02 TX+ RX+ RX- TX-

Audio In Audio Audio Audio Audio
AUDIO Audio In A Alarm A Alarm B
B Ctrl A Out A Out B Ctrl B
DoorPhB DoorPhA DoorPhA DoorPhB
DOORPHONE
1 1 2 2

3.1.3.2 Connecting a Please-Wait Message Player

This is connected via the AUDCTRL output (control contact open when idle) and the AUDIN
input of the AUDIO connector.
___change-begin___
___change-end___
Audio Input Characteristics:
Input impedance : 600 Ohms
Fuse Characteristics:
- Max. power : 10 W
- Max. voltage : 60 V
- Max. current : 500 mA
The contacts of the alarm and doorphone controls have the same electrical

characteristics as those indicated above.

3.1.3.3 Connecting a Background Music Tuner
This is connected via the AUDIN input of the AUDIO connector.
___change-begin___
 !"#!$% & '#! & ( ) "#!* &             17/160
  
Chapter 3 / 

___change-end___
Audio Input Characteristics:
- Input impedance : 600 Ohms
- Input level: access + 4.7 dBr or + 15 dBr
3.1.3.4 Connecting an Alarm
The alarm is activated in the event of a false stopping of the system.
It is connected via the ALARM output (control contact closed when idle) of the AUDIO
connector.
___change-begin___
___change-end___
3.1.3.5 Connecting a Broadcast Loudspeaker
Broadcast loudspeakers are connected via the AUDOUT output of the AUDIO connector.
___change-begin___
18/160  !"#!$% & '#! & ( ) "#!* &            
  
 / 

___change-end___
Audio Output Characteristics:
- Output impedance: < 500 Ohms
- Output level: access + 3 dBr
3.1.3.6 Connecting a General Ringer
The general ringer is connected via the CENRG output of the AUX connector.
___change-begin___
___change-end___
3.1.3.7 Connecting a Doorphone
2 doorphone types are available, depending on the operating mode used:
- Type A: relay-controlled doorphones (e.g. NPTT)
- Type B: doorphones controlled by MF Q23 signals requiring an SLI interface (e.g.
TELEMINI and UNIVERSAL DOORPHONE)
The doorphone interface comprises an intercom and an optional latch powered by the mains
supply through a SELV (Safety Extra Low Voltage) transformer.
It is connected via the DOORPHA and DOORPHB outputs (control contacts open when idle)
of the DOORPHONE connector.

 !"#!$% & '#! & ( ) "#!* &             19/160
  
Chapter 3 / 

3.1.3.7.1 Connecting a NPTT Doorphone

___change-begin___
___change-end___
- A single doorphone with doorstrike may be connected to the system.
- The system also allows for the connection of 2 doorphones without latch.
3.1.3.7.2 Connecting a Telemini and Universal Doorphone
These doorphones require the use of a Z station interface.
- Several of these doorphones can be connected to the system; the limit is determined by
the maximum number of analog stations the system can support.
- A system cannot have Telemini and Universal doorphones at the same time.
3.1.3.8 Using the 12V Output
The GROUND and + 12V outputs on the AUX connector allow for the connection of an
external 12V device with a maximum energy consumption of 150 mA (OXO Connect S and
OXO Connect M) or 300 mA (OXO Connect L).

3.2 PowerMEX

20/160  !"#!$% & '#! & ( ) "#!* &            
  
 / 

3.2.1 Hardware description

3.2.1.1 Overview
The PowerMEX board is a controller board for extension or module expansion.
The PowerMEX board (POWER Module EXpansion) performs the controller functions in the
expansion platforms.
3.2.1.2 Daughter Board
The PowerMEX board is equipped with an HSL1 (High Speed Link) board for interconnecting
with the basic platform.

Figure 3.11: HSL1 Daughter Board on PowerMEX Board

3.2.2 Hardware configuration

3.2.2.1 Meaning of the LED Indications

Figure 3.12: PowerMEX

 !"#!$% & '#! & ( ) "#!* &             21/160
  
Chapter 3 / 

Name Color Function

POWER Red/Green - Mains operation: steady green LED
- Battery operation: steady yellow LED
- Idle: flashing red LED
FAN Red/Green - Both fans functioning: steady green LED
- 1 or both fans down: steady red LED

3.2.3 External connections

3.2.3.1 Output Ports

Figure 3.13: PowerMEX

Available functions:
- MAIN: HSL to basic module (cable max. length: 5 meters).
RJ45 pin 1 2 3 4 5 6 7 8
MAIN outputs TX+ TX- RX+ RX-

3.2.3.2 Connection
The PowerMEX board is connected to the MODULE 1 or MODULE 2 connector on the
PowerCPU EE board: see Boards - Hardware configuration - General Connection Diagram .

3.3 BRA

3.3.1 Hardware description

The BRA (Basic Rate Access) board provides the basic access points (2 x 64-Kbps
B-channels + 1 x 16-Kbps D-channel per access) for connecting the system to the ISDN digital
public network (point-to-point or multipoint T0 link) and, starting with version R2.0, to a private
network (point-to-point DLT0 link); Several versions are offered:
- BRA2-2: 2 T0 accesses
- BRA4-2: 4 T0 accesses
- BRA8: 8 T0 accesses
With OMC it is possible to define the operating mode access by access: T0 (ISDN) or DLT0
(QSIG). If the choice is DLT0 (QSIG), the following operating mode may be defined: master =
Network (NT), slave = User(TE)

22/160  !"#!$% & '#! & ( ) "#!* &            
  
 / 

Note:
Configuration in T0/DLT0 is done by access pairs; if an access (04-001-01 for example) is configured in
DLT0, the 2nd one (04-002-01) must also be configured in DLT0.

3.3.2 External connections

3.3.2.1 Output ports (faceplate)

 !"#!$% & '#! & ( ) "#!* &             23/160
  
Chapter 3 / 

RJ45 pin 1 2 3 4 5 6 7 8
Outputs TX+ RX+ RX- TX-

3.3.2.2 Connecting a T0 access

The OXO Connect system can be installed near the digital network termination or at a certain
distance (up to 350 m), as required.
3.3.2.2.1 Connection without T0/S0 forwarding
___change-begin___
___change-end___
3.3.2.2.2 Connection with T0/S0 forwarding
In the event of a loss of tension or CPU malfunction, the ISDN-EFM box allows a T0 access to
be forwarded directly to an S0 station.

24/160  !"#!$% & '#! & ( ) "#!* &            
  
 / 

Note:
The AFU-1 board (daughter board of the CPU board) must be equipped so as to detect a loss of tension.
Description of the ISDN-EFM box

Connections
The ISDN-EFM box must be installed as close as possible to the system (3 m maximum). All
the box connections are made with straight RJ45-RJ45 cables.
Output connectors functions:
- BRA: connection of T0 access to be forwarded.
- NT: connection of ISDN network termination.
- S0: connection of forwarding S0 station.
- CPU: connection to the CPU board's AUDOUT connector.
- AUX: connection of Audio out, Alarm, General bell and 12 V use auxiliaries; since AUX is a
copy of the CPU board's AUDOUTde connector, check the sheet of the CPU board in use
for connection recommendations.

 !"#!$% & '#! & ( ) "#!* &             25/160
  
Chapter 3 / 

3.4 PRA

3.4.1 Hardware description

The PRA board (Primary Rate Access) board provides 1 primary access for connecting the
OXO Connect system to the ISDN digital public network or to private networks:
- PRA -T2, DLT2: 30 x 64-Kpbs B-channels + 1 x 64-Kbps D-channel; 2048 Kbps.
- PRA-T1: 23 x 64-Kbps B-channels + 1 x 64-Kbps D-channel; 1544 Kbps
- PCM R2: 30 x 64 Kbps B-channels + 1 x 4 Kbps signaling channel; 2048 Kbps.
There are several connection options: T2 120-ohm symmetrical pairs and T1 100-ohm
symmetrical pairs. A coaxial 75-ohm connection is available using an external adapter kit.

26/160  !"#!$% & '#! & ( ) "#!* &            
  
 / 

3.4.2 Hardware configuration

3.4.2.1 Board type definition (Citroën straps)
The board type is defined by the Citroën strap solder:
- T2 (ex-factory): no solders
- T1: solder on strap 1
- DLT2: solder on strap 2
- PCM R2: solder on strap 4
3.4.2.2 Connection (120- ohm symmetrical pairs)

 !"#!$% & '#! & ( ) "#!* &             27/160
  
Chapter 3 / 

The PRA board is connected to a digital line termination (DLT) by 2 reinforced symmetrical
pairs.
Cable impedance: 120 Ohms +/- 20% between 200 kHz and 1 MHz; 120 Ohms +/- 10% at 1
MHz.
We recommend using an L120-series cable (or the L204 equivalent).
The distance T2-DLT is limited by the amount of loss between the DLT and T2, which must not
exceed 6 dB at 1024 kHz.

3.4.3 External connections

3.4.3.1 Output ports (faceplate)
T2 board example

28/160  !"#!$% & '#! & ( ) "#!* &            
  
 / 

RJ45 pin 1 2 3 4 5 6 7 8
NETW outputs RX+ RX- TX+ TX-
PBX outputs TX+ TX- RX+ RX-

NETW: connection to public network DLT.

PBX: network operation (QSIG).
3.4.3.2 Alarm LEDs

T2 Name T1 Name Feature

BUSY BUSY B-channels busy (red LED lights up if at least 1 B-channel is busy)
RAI (ATD) RAI Remote frame alarm (red LED lights up on alarm)
AIS (SIA2M) AIS Too many "1's in the 2-Mbit binary train (red LED lights up on alarm)
NOS (MS) NSIG Absence of 2-Mbit signal (red LED lights up on alarm)
CRC (TE) CRC CRC error (red LED lights up on alarm)
LOS (PVT) NSYN Loss of frame alignment (red LED lights up on alarm)

In brackets: French abbreviations

3.5 MIX-2

3.5.1 Hardware description

The MIX-2 (Mixed Lines) board serves to connect ISDN basic accesses (T0), digital stations
(UA) and 2-wire analog terminals (Z). 3 board versions are available:
- MIX244-2: 2 T0 accesses, 4 UA interfaces and 4 Z interfaces
- MIX484-2: 4 T0 accesses, 8 UA interfaces and 4 Z interfaces
- MIX448-2: 4 T0 accesses, 4 UA interfaces and 8 Z interfaces
Note:
Contrary to the BRA-2 board, the MIX-2 board's T0 accesses cannot be configured as DLT0 Network.
Only DLTO User is allowed in QSIG mode.
Example: MIX484-2 board

 !"#!$% & '#! & ( ) "#!* &             29/160
  
Chapter 3 / 

3.5.2 External connections

3.5.2.1 OUTPUT PORTS (FACEPLATE)

30/160  !"#!$% & '#! & ( ) "#!* &            
  
 / 

RJ45 pin 1 2 3 4 5 6 7 8
Z outputs ZA ZB
UA outputs L1 L2
T0 outputs TX+ RX+ RX- TX-

3.5.2.2 CONNECTING AN ANALOG STATION (Z)

Follow the rules in the "SLI-2 board" section.
3.5.2.3 CONNECTING A DIGITAL STATION
Follow the rules in the "UAI board" section.
3.5.2.4 CONNECTING A T0 BASIC ACCESS
Follow the rules in the "BRA-2 board" section.

3.6 Mini-MIX
The Mini–MIX daughter board is an optional daughter board plugged on the PowerCPU EE
board.
Note:
The Mini-MIX daughter board requires BACKXS-N back panel and PSXS-N power supply module. The

 !"#!$% & '#! & ( ) "#!* &             31/160
  
Chapter 3 / 

Mini-MIX daughter board can be used only in an OXO Connect Compact.

The Mini–MIX daughter board has the following features:
Two T0 (ISDN Basic Rate Access) interfaces
Two Z (SLI Analog Extension Access) interfaces
One local OBC to handle initialization and low level signaling

Figure 3.30: Mini-MIX daughter board

The Mini–MIX is detected via ASL (just like a peripheral board).
The Mini–MIX is located on position “6” (fixed) of ASL0 .

32/160  !"#!$% & '#! & ( ) "#!* &            
  
 / 

The Mini–MIX drives the Mini–MIX led ( previously WAN led ) on the front stiffener.
LED “ON” indicates that :
- the Mini–MIX daughter board is present and accepted by the mixed board license,
- the Backpanel supports 100V distribution (PSTYPE=”0”).
___change-begin___
___change-end___
Figure 3.31: Mini-MIX connections on PowerCPU EE Board
Inter–connections between the Mini–MIX and the PowerCPU EE are made through 2BergStak
connectors (already used for daughter boards AFU-1, HSL, etc.)

 !"#!$% & '#! & ( ) "#!* &             33/160
  
Chapter 3 / 

3.7 AMIX-1

3.7.1 Hardware description

The AMIX-1 (Analog Mixed Line) board is used to connect the analog public network (PSTN)
to the PBX. It has the following characteristics:
- 4 analog line accesses
- a maximum of 8 UA interfaces
- a maximum of 8 Z interfaces
- an OBC system interface supporting AT, Z and UA signaling
- protection features
- the PFCT (Power Failure Cut Through) feature which allows a local analog set to connect
directly to a network line in the event of a power cut or a software failure
Note:
The AMIX-1 board is required to connect the OXO Connect Compact platform to the analog public
network (PSTN). It can be used for OXO Connect Small, Medium, Large platforms.
The AMIX-1 board can take the following 2 daughter boards:
- GSCLI
- CLIDSP

3.7.2 External connections

3.7.2.1 OUTPUT PORTS (FACEPLATE)

: indicates the assignment ports for the PFCT (Power Failure Cut Through) feature: the Z2
plug is connected to a Z set, the AT1 plug to the PSTN.

34/160  !"#!$% & '#! & ( ) "#!* &            
  
 / 

RJ45 pin 1 2 3 4 5 6 7 8
AT outputs AT_B_RING AT_A_TIP
UA outputs UA_a UA_b
Z outputs Z_a Z_b

3.7.2.2 CONNECTING AN ANALOG STATION (Z)

For more information, refer to the SLI-2 board document.
3.7.2.3 CONNECTING A DIGITAL STATION
For more information, refer to the UAI document.

3.8 UAI

 !"#!$% & '#! & ( ) "#!* &             35/160
  
Chapter 3 / 

3.8.1 Hardware description

The UAI board allows the connection of digital stations (UA). Two board versions are available:
- boards without external power supply capability:
• UAI4: 4 UA interfaces
• UAI8: 8 UA interfaces
• UAI16: 16 UA interfaces
- boards with external power supply capability:
• UAI16-1: 16 UA interfaces
3.8.1.1 Differences between the two boards
The UAI16-1 board is equipped with 2 ASICs OSIRIS while the UAI4/8/16 boards are
equipped with ASICs CATS (one ASIC OSIRIS replaces 2 ASICs CATS).
The system software detects whether the board is equipped with CATS or OSIRIS; if the ASIC
OSIRIS is detected, the software can also detect whether the board is connected to an
external power supply.
The UAI-16 board allows to remotely supply the terminals connected to the 16 interfaces from
a EPS48 external power supply connected to interface 1 using an external adaptation power
cable (splitter).
3.8.1.2 BOARDS UAI4, UAI8 and UAI16

36/160  !"#!$% & '#! & ( ) "#!* &            
  
 / 

3.8.1.2.1 Output ports (Faceplate)

 !"#!$% & '#! & ( ) "#!* &             37/160
  
Chapter 3 / 

RJ45 pin 1 2 3 4 5 6 7 8
Outputs L1 L2

3.8.1.3 UAI16-1 board

3.8.1.3.1 Output ports (Faceplate)

38/160  !"#!$% & '#! & ( ) "#!* &            
  
 / 

RJ45 pin 1 2 3 4 5 6 7 8
Outputs 1 L1 L2 0V +48 V
Outputs 2 to 16 L1 L2

3.8.2 External connections

3.8.2.1 CONNECTING A DIGITAL STATION
3.8.2.1.1 Connection without external power supply
The terminals are equipped with a cable and a self-acting switch that plugs into the wall
socket. Each terminal is connected up by a pair of 0.5 or 0.6 mm diameter wires.
System - Digital station distances:
- 0.5 mm SYT type cable: 800 m (station without option) or 600 m (station with S0 or Z
option)
- 0.6 mm 278 type cable: 1,200m (station without option) or 850m (station with S0 or Z
option)

 !"#!$% & '#! & ( ) "#!* &             39/160
  
Chapter 3 / 

3.8.2.1.2 Connection with external power supply

A splitter allows the separation of the UA peripheral connection and the EPS48 external power
supply.

3.9 SLI-2

3.9.1 Hardware description

40/160  !"#!$% & '#! & ( ) "#!* &            
  
 / 

The SLI-2 board (Single Line) allows the connection of 2-wire analog terminals (Z). 3 board
versions are available:
- SLI4-2: 4 Z interfaces
- SLI8-2: 8 Z interfaces
- SLI16-2: 16 Z interfaces

3.9.2 External connections

3.9.2.1 OUTPUT PORTS (FACEPLATE)
___change-begin___
 !"#!$% & '#! & ( ) "#!* &             41/160
  
Chapter 3 / 

___change-end___
RJ45 pin 1 2 3 4 5 6 7 8
Outputs ZA ZB

3.9.2.2 CONNECTING AN ANALOG Z STATION

The terminals are equipped with a cable and a self-acting switch that plugs into the wall
socket. Each set is connected up with a pair of 0.5 or 0.6-mm wires (the maximum distance
with 0.5-mm cabling is 1.3 km).
___change-begin___
___change-end___
3.10 LanX-2

42/160  !"#!$% & '#! & ( ) "#!* &            
  
 / 

3.10.1 Hardware description

The LanX-2 board (Ethernet LAN Switch) serves to connect Ethernet terminals (IEEE 802.3
compatible). 2 board versions are available:
- LanX8-2
8 10/100 BT Ethernet ports (ports 1 to 7: MDI-X/crossover; Uplink: MDI-II/straight link)
- LanX16-2
16 10/100 BT Ethernet ports (ports 1 to 15: MDI-X/crossover; Uplink: MDI-II/straight link)

The LanX8-2 and LanX16-2 integrate respectively 1 or 2 Ethernet Gigabit ports for a
Lanswitch/Layer 2 configuration. Any port can be used as an Uplink, as all the ports are auto
MDI/MDIX.

3.10.2 Configuration examples

3.10.2.1 Configuration Example

 !"#!$% & '#! & ( ) "#!* &             43/160
  
Chapter 3 / 

3.10.3 External connections

3.10.3.1 OUTPUT PORTS (FACEPLATE)
3.10.3.1.1 LANX-2 board

44/160  !"#!$% & '#! & ( ) "#!* &            
  
 / 

The LEDs of the A and B ports are both located at the top of the board. The LED display is as
follows:
- Green LED (left) = link status and activity:
• LED off: link disconnected
• LED steady: link connected
• LED flashing: link active
- Yellow LED (right) = speed:
• off: low speed (10 or 100 Mb for Gigabit port, 10 Mb for the other ports)
• on: high speed (1 Gb for Gigabit port, 100 Mb for the other ports)
RJ45 pin 1 2 3 4 5 6 7 8
Ports 1 to 14 RX+ RX- TX+ TX-
GE1, GE2 TR0+ TR0- TR1+ TR2+ TR2- TR1- TR3+ TR3-

• Ports 1 to 14: 10/100 BT ports.

• GE1, GE2: 10/100/1000 BT ports.
3.10.3.2 CONNECTION PRINCIPLES
3.10.3.2.1 Basic 10/100 BT connection

 !"#!$% & '#! & ( ) "#!* &             45/160
  
Chapter 3 / 

3.10.3.2.2 MDI-X to MDI-X connection

3.11 APA

3.11.1 Hardware description

The APA boards can only be used on systems running a software version posterior to R2.0.

The APA board (Analog Public Access) allows the connection of analog trunk lines (TL). Two
board versions are available:
- APA-4: 4 TL interfaces
- APA-8: 8 TL interfaces

46/160  !"#!$% & '#! & ( ) "#!* &            
  
 / 

X5: CLIDSP daughterboard plugging connector (detection of CLIP signal).

X60, X61, X62, X70, X71, and X72: GSCLI daughterboards plugging connectors (Ground
Start signaling).
3.11.1.1 CLIDSP BOARD EQUIPMENT
The signal needed to manage the CLIP (Calling Line Identification Presentation) is generated
at the CPU board level except in the following cases, which require a CLIDSP board (to be
installed on connector X5 of the board): US, UK and all countries using only Dual Tone
(DT-AS) as alert signal.
The CLIDSP board will also be necessary to detect the CLIP in the on-hook state (later
phase).

3.11.2 External connections

 !"#!$% & '#! & ( ) "#!* &             47/160
  
Chapter 3 / 

3.11.2.1 OUTPUT PORTS (FACEPLATE)

RJ45 pin 1 2 3 4 5 6 7 8
Output1 ZSETB ZSETA LB-Ring LA-Tip ZB ZA
Outputs 2 to 8 LB-Ring LA-Tip

Note:
Z set B1 and Z set A1: connection to Z set for cut-through functionality. ZB1 and ZA1: connection to a Z
access for cut-through functionality.

3.11.2.2 CONNECTING A TL
3.11.2.2.1 Without TL forwarding

3.11.2.2.2 With LR forwarding

48/160  !"#!$% & '#! & ( ) "#!* &            
  
 / 

In the event of power failure or CPU malfunction, this solution allows connection of the analog
line (connected to the APA board's equipment 1) to an analog station.

Note:
US connection features
- APA board equipped with Ground Start signaling: Ring is connected to the network's +
polarity while Tip is connected to the - (ground if using conventional battery).
- APA board equipped with Loop Start signaling: In case of conventional battery, Tip is
normally connected to the network equipment's ground and Ring to the network's - polarity.
Nevertheless, maintenance operations may temporarily or permanently inverse these
polarities: the connection of each of the battery's terminals to the earth cannot be ensured.
In the case of va riable battery, no terminal is connected to ground: the Tip and Ring
outputs are variable.

3.12 Power Supplies

3.12.1 Hardware description

3.12.1.1 Power Supply PS1/PS1N
Power supply PS1/PS1N provides the different voltages required to operate an OXO Connect
S platform and also acts as a backplane board (slots 1, 2 and CPU).

 !"#!$% & '#! & ( ) "#!* &             49/160
  
Chapter 3 / 

3.12.1.2 Power Supply PS2/PS2N

Power supply PS2/PS2N, which provides the different voltages required to operate an OXO
Connect M platform, consists of 2 boards:
- PCH2: charger board
- PCO2: converter board

50/160  !"#!$% & '#! & ( ) "#!* &            
  
 / 

3.12.1.3 Power Supply PS3/PS3N

Power supply PS3/PS3N, which provides the different voltages required to operate an OXO
Connect L platform, consists of 2 boards:
- PCH3: charger board
- PCO3: converter board

 !"#!$% & '#! & ( ) "#!* &             51/160
  
Chapter 3 / 

3.12.1.4 Batteries
Equipment:
- OXO Connect S: 1 battery
- OXO Connect M: 2 batteries mounted in parallel
- OXO Connect L: 3 batteries mounted in series

52/160  !"#!$% & '#! & ( ) "#!* &            
  
 / 

Battery characteristics:
- sealed lead battery
- 1,2 Ah / 12 V
- fire resistance better than or equal to UL94-V2
Maintenance:
To guarantee system shutdown without data loss in the event of a mains power failure, or if the
mains plug is unplugged at the wall socket, replace the batteries every two years. This
maintenance operation is vital to guarantee sufficient power autonomy to allow the files to be
saved before the system shuts down.
In the case of only a voice module (without Hard Disk), the standalone time is approximately
20 minutes.
3.12.1.5 UPS
A UPS (Uninterruptible Power Supply) is recommended because it increases the backup time
provided by the system’s batteries. A maximum of 2 OXO Connect platforms can be
connected to a UPS.

 !"#!$% & '#! & ( ) "#!* &             53/160
  
Chapter 3 / 

3.12.1.5.1 Equipment
The following table indicates compatible UPS models to use with each OXO Connect system
for a power autonomy of about 1 hour (40 minutes for the OXO Connect L + extension OXO
Connect L used with a standard configuration):
System UPS 220 V UPS 110 V
OXO Connect S Pulsar ellipse 300 Pulsar ellipse 300 USB
OXO Connect M Pulsar ellipse 650S Pulsar ellipse 650 RS232
OXO Connect L Pulsar ellipse 1200S Pulsar ellipse 1200 RS232

54/160  !"#!$% & '#! & ( ) "#!* &            
  
 / 

System UPS 220 V UPS 110 V

OXO Connect L + extension OXO Pulsar ellipse 1200S Pulsar ellipse 1200 RS232
Connect L

3.12.1.5.2 Choice of UPS

The following table indicates for each OXO Connect system (in extreme configurations) the
consumption that is used to choose a UPS from the various models offered by UPS
manufacturers:
System Configuration Primary consumption
OXO Connect S 24 terminals 50 W
OXO Connect M 48 terminals 70 W
OXO Connect L 96 terminals 105 W
OXO Connect L + extension OXO 192 terminals 210 W
Connect L

3.12.1.6 EPS48 External Power Supply

The EPS48 external power supply (48V - 1A) is designed to power the UAI16-1 boards, thus
enabling the connection of power-hungry peripherals without a need for another module or a
bigger module.
Plugged into the electrical power supply, a 2 m power cable with an 8-pin RJ45 connector
powers the splitter used with the UAI16-1 board.
A green lamp indicates tension.
The EPS48 external power supply's connection into the main power supply must be located as
close as possible to the system and be easily accessible.
table 3.18: Output Points
RJ45 pin 1 2 3 4 5 6 7 8
Outputs 0V 48 V

 !"#!$% & '#! & ( ) "#!* &             55/160
  
   

     

4.1 8001/8001G Deskphones

4.1.1 8001/8001G Deskphone description

4.1.1.1 About this chapter
The following paragraphs are intended for administrators in charge of installing and
commissioning 8001/8001G Deskphone sets for users declared on OXO Connect nodes.
8001/8001G Deskphone sets are SIP sets, based on IETF standards (RFCs).
Note:
For readability purposes, throughout this chapter the term "set" is used to refer to 8001/8001G
Deskphone sets.
The following paragraphs provide:
- A description of the sets (see: Set ergonomics and technical specifications )
- The procedure to commission the set ( Dedicated Sets - 8001 Deskphone )
- The procedure to upgrade set binaries ( Dedicated Sets - 8001 Deskphone - Upgrading set
binaries )
- The procedure to replace a 8001/8001G Deskphone by another 8001/8001G Deskphone
(see: Dedicated Sets - 8001 Deskphone - Replacing the set by another 8001/8001G
Deskphone set )
- The procedure to configure the user and password on a 8001/8001G Deskphone (see:
Dedicated Sets - 8001 Deskphone Commissioning - 8001/8001G Deskphone password
management )
- The process to start a 8001/8001G Deskphone as 8001 SIP Phone in replacement of a
same 8001/8001G Deskphone initially installed as Open SIP Phone (see: Dedicated Sets
- 8001 Deskphone Commissioning - Replacing the set by another 8001/8001G Deskphone
set )
User operations are described in a dedicated user guide.
4.1.1.2 Set ergonomics and technical specifications

56/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

Figure 4.1: Set layout

Physical characteristics:
- Corded handset (or headset). In its standard version, the set comes with a corded comfort
handset.
- Two-level adjustable foot stand: 40° or 60°
- Wall-mountable
- Operating temperature: 0°C to 45°C
- Operating humidity: 10% to 90%
Audio characteristics:
- Audio codec: G711 (A-law and µ-law), G723.1, G.729AB
Power characteristics:
- Power over Ethernet (IEE 802.3af)
- Power adapter (DC 5V/1A output)
Connectivity:
- 8001 DeskPhone: LAN: 2 x RJ45 10/100M Ethernet ports
- 8001G Deskphone: LAN: 2 x RJ45 10/100/1000M Ethernet ports
- 1 x 3.5 mm Jack port (headset connection)
- 1 x RJ9 port (handset connection)
- 1 x RJ9 port (headset connection 4-Pin (CTIA, stereo))
- 1 x power supply port (AC/DC power adapter connection)
This supply port is reserved for future use (no power adapter available with the current

 !"#!$% & '#! & ( ) "#!* &             57/160
  
Chapter 4    % 

version).
Note:
For a complete view of the set technical specifications, refer to the 8001/8001G Deskphone data sheet
available on the business portal (BPWS).

4.1.2 8001/8001G Deskphone Commissioning

4.1.2.1 Overview
The 8001/8001G Deskphone sets are plug&phone, which means they are automatically
created in the OXO Connect, when connected to the network. A default certificate in the
system allows plug&phone.
4.1.2.2 Prerequisites
The 8001/8001G Deskphone software must be in version 3.6.0.5. If a previous software
version is installed on the set, the set starts as an "Open SIP Phone" and is not recognized as
8001/8001G Deskphone SIP Phone".
The software is downloaded according to the initial 8001/8001G Deskphone software version
of the set:
1. Sets having a software version prior to 3.5.0.8 must be upgraded to the intermediate
version 3.5.0.8
2. Sets are upgraded to version R120-v3.6.0.5
- The OXO Connect must be operational
- A free IP address must be available for the set
- A port with PoE must be available on a switch
- If the set is configured to start in dynamic mode (default configuration, a DHCP server
must be configured:
• If using the OXO Connect DHCP server: a range of available IP addresses must be
configured (in OMC, go to ALU IP Phones: DHCP IP Range).
• If using another DHCP server: the URL for the configuration files must be provided.
This URL is indicated using two proprietary options of DHCP server:
• Option 66 must specify the DM IP address, the value of this option must contain
<OXO Connect_IP_address:10443>
• Sub option 67 of option 43 (DHCP Vendor Specific information) must contain a
string value set to « /dmcfg/ »
The URL to download the configuration files is https://<OXO
Connect_IP_address>:10443/dmcfg.
The CGI script included in the URL is executed on the OXO Connect to create the
device (if necessary) and generate the configuration file.
4.1.2.3 Connecting the set to the LAN
Once the IP configuration is done, the set can be connected to the LAN:
1. Turn the set over so that you can see its base.
2. Plug the RJ45 cable into the set's LAN connector.
3. Connect the RJ45 cable to the LAN.

58/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

The set starts and connects to the system

4.1.2.4 Connection to the system
At first appearance of the set, the system creates the configuration file associated to this set
and automatically declares the set in the system subscribers' list.
The set sends an HTTPS request to retrieve its configuration files.
Note:
The SIP parameter configuration file is named <MAC address>.xml
Example: 00809f5607ae.xml (for a set whose MAC address is 00:80:9F:56:07:AE)
The set being plug&phone, it starts automatically and can be used straight away.
The set can be further configured in OMC. It is visible in the subscribers list as SIP Phone
(8001) or SIP Phone (8001G).
4.1.2.5 Manual (static) configuration
The set IP parameters can be modified after first initialization.
On the set itself, connected to the system:
1. Press the OK button, or the Menu softkey
2. Go to System settings > Advanced settings > Advanced
3. Select Network > LAN Port
4. Select the Static mode
5. Configure the set IP address, ensuring first that it is a free address
6. Configure other IP parameters: IP subnetwork mask, and gateway (that is router)
7. Configure DNS settings
8. Configure port management settings
9. Go to System settings > Advanced settings > Advanced > Auto Provision
Enter the URL: https://<OXO Connect_IP_address>:10443/dmcfg and select
HTTPS as protocol
10. Press the Save softkey
Important:
If the OXO Connect is installed and configured in a VLAN topology, the VLAN must be manually
enabled in the advanced settings of the set. The corresponding OXO Connect VLAN Value must
be entered manually in set configuration.

4.1.2.6 Upgrading set binaries

If requested:
1. In OMC, select Import/Export > File Management For third Party Devices
2. Import the binary files and firmware configuration files in the directory named: Binary
3. Reboot the set manually
When the set connects to the OXO Connect, it upgrades its software, provided the binaries
imported in the system and the binaries present in the set are of a different version.

 !"#!$% & '#! & ( ) "#!* &             59/160
  
Chapter 4    % 

Note:
Set binaries can be imported or deleted, but not exported

4.1.2.7 Replacing the set by another 8001/8001G Deskphone set

In case of a replacement by another 8001/8001G Deskphone set, modify the MAC address of
the set in OMC.
There is no backup of terminal data, which means that the local call log and saved contacts
are lost.
To replace a set initially installed as Open SIP phone by a same set and have it recognized
properly by the system:
1. Disconnect the phone from the network
2. In OMC, delete the registration Open SIP Phone
3. Reconnect the 8001/8001G Deskphone
It initializes normally and the OXO Connect license-bypass mechanism makes it appear as
a SIP 8001/8001G Deskphone.
It is preferable to disconnect 8001/8001G Deskphone set from the network during this
operation. Once reconnected, the set initializes normally and the OXO Connect license-bypass
mechanism makes it appear as a SIP phone 8001/8001G Deskphone .
4.1.2.8 8001/8001G Deskphone password management
After a 8001/8001G Deskphone SIP Phone starts with the OXO Connect, the user password
for the set web interface is changed from the default values: root / root to admin / admin.
To configure the set, if no new administrator password has been manually entered:
- On the 8001/8001G Deskphone set : when the password is requested, do not enter
anything and select OK (or try as 000000 password)
- From the web Admin interface, enter: admin / admin
If there is a specified password, different from the default password, for a 8001/8001G
Deskphone SIP phone configured in the OXO Connect, after the set is connected to the
system, the login changes to admin with the password specified in OMC System Misc/SIP
Phone Admin password/SIP phone for the phone.
If a manual 8001/8001G Deskphone SIP phone reset to factory settings is requested (for
instance if the administrator password is lost), on the set:
1. Go Menu > Functions Settings > Dial to find:
Set the option to "off" (no dial by name)
2. With the phone idle, dial *3*3*3"
This reboots the set to factory settings

4.2 8018 DeskPhone

4.2.1 Detailed description

4.2.1.1 Environmental requirements

60/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

- Storage temperature: -25°C to 55°C (ETSI EN 300 019-1-1 Class 1.2)

- Transportation temperature: -40°C to 70°C (ETSI EN 300 019-1-2 Class 2.3)
- Temperature controlled enclosed location: -5°C to 45°C (ETSI EN 300 019-1-3 Class 3.2)
- Relative humidity: 5% to 95% (ETSI EN 300 019-1-3 Class 3.2)
4.2.1.2 Hardware description
4.2.1.2.1 Phone layout

Figure 4.2: 8018 DeskPhone set layout

4.2.1.2.2 Embedded hardware

A BCM1103 CPU is included .
32 Mb RAM (DDR1), 32 Mb Flash (NOR).
4.2.1.2.3 Audio, handsets, hands free and headset
The 8018 DeskPhone is equipped with a USB connector instead of a standard microphone
connector.
It comes in standard version with a comfortable corded handset.
It works in hands free mode at the user request.
4.2.1.2.4 Screen
The set screen is a black and white graphical display of 50 by 128 pixels with white backlight.
4.2.1.2.5 Keys

 !"#!$% & '#! & ( ) "#!* &             61/160
  
Chapter 4    % 

Dialing keypad
The dialing keypad is also used as alphabetical keyboard. Press the "alpha" fixed key, whose
label displays 123 < > abc. By default, the set is in numeric mode and the key is unlit. Press
the alpha key to switch to alphabetic mode.
On the dialing keypad, the selected character is changed with a short press on the key:
Press To input any of (in this order):
1 space | - 1
2 abcABC2
3 defDEF3
4 ghIGHI4
5 jklJKL5
6 mnoMNO6
7 pqrsPQRS7
8 tuvTUV8
9 wxyzWXYZ9
0 .,;:“?!0
* *+%$/~&()[]=
# #@

Fixed keys
On all sets:
- Two fixed keys below the keypad (start call key: and stop call key: ) allow to
perform several actions
- A four-direction set of navigation keys (left, right, up, down) allows to select the different
options available on the screen. The OK button in the center of the navigation validates the
selection.
- The c key to the left of the navigation allows to cancel the current action.
- Sensitive (piano) keys are located above the black grid of the lower part of the set.
Starting from the left to the right, they provide access to the following features:
• mute sound

• decrease sound volume

• increase sound volume

• put loudspeaker in service

• messaging services

Integrated additional programmable keys

On 8018 DeskPhone sets, seven add-on keys are available with a digital label next to each

62/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

one. The first key triggers switching between numeric and alphabetical characters. The second
key is labeled F1 (Hold in the US), and the third key is labeled F2 (Transfer in the US). By
default, pressing the F1 key puts the current call on hold and pressing the F2 key transfers the
current call.
4.2.1.3 USB connector
The 8018 DeskPhone can be charged with boosted current via USB.
To configure USB boost charging:
1. In OMC (expert mode), go to Users/Base stations List -> Users/Base stations List ->
Details -> Misc.
2. Double-click the user in the list to open the User dialog box
3. In the User dialog box, click Misc.
4. Review/modify the following attribute:
USB Boost charging • Disabled (default value): boosted current is disabled
• Enabled: boosted current is enabled

4.2.2 Commissioning
4.2.2.1 Connecting the set
To connect the set to the PBX:
1. Plug the RJ45 cable into the set LAN connector
2. Connect the RJ45 cable to the LAN itself
3. If your set is not powered by PoE, plug the AC/DC external adapter to the set power supply
connector and connect the plug to the power supply
Once the set is connected and powered up, it automatically starts initializing.
4.2.2.2 Set initialization
By default, 8018 DeskPhone sets initialize dynamically and retrieve IP information
automatically.
You can change this initialization mode. Static initialization is mandatory when the system
does not use a DHCP server.
To switch from dynamic initialization to static initialization and modify IP parameters:
1. Wait for the set to initialize and reach the end of the Network setup process, displayed on
screen
2. Press simultaneously the star and pound keys
This displays IP settings
3. Use the soft key next to an option to modify the selection
4. Validate your modifications with the soft key next to the tick symbol
4.2.2.2.1 Requested IP parameters
The following information must be provided for static initialization:

 !"#!$% & '#! & ( ) "#!* &             63/160
  
Chapter 4    % 

- IP address (set's address)

- Subnetwork mask
- Router address
- TFTP1 server address: OXO Connect IP address
- Use VLAN: this box must be checked to enter a VLAN number
- VLAN number if necessary
- TFTP port
The TFTP address(es) to enter may differ according to system configuration.
Please contact your system administrator for details on the configuration of your system.
With dynamic initialization, IP parameters are automatically sent by a DHCP server to the
phone.
4.2.2.2.2 Deny of download
If the downloaded version is different from the version installed on the set and if the
downloaded binary is incompatible with the hardware/software, the terminal denies it and
signals the problem to the Communication Server.
The terminal requests binary files at each reset until a compatible binary is found.
Deny of download also applies to SIP binary.
4.2.2.3 Binary file download
On 8018 DeskPhone sets, binary upgrade is silent and takes place in the background, once
the OXO Connect has detected that an upgrade is required. Once the file is downloaded by
the set and when the terminal is idle, it resets and implements the new software.
While downloading the new firmware, the set runs with the current firmware.

4.3 8028/8038/8068 Premium DeskPhones

4.3.1 Detailed description

4.3.1.1 Overview
The available IP DeskPhones are:
- 8068 Premium DeskPhone
- 8038 Premium DeskPhone
- 8028 Premium DeskPhone
Two types of 8068 Premium DeskPhone are available:
- 8068 Premium DeskPhone with Bluetooth
- 8068 Premium DeskPhone without Bluetooth
4.3.1.2 Environmental requirements
- Storage temperature: -25°C to 55°C (ETSI EN 300 019-1-1 Class 1.2)

64/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

- Transportation temperature: -40°C to 70°C (ETSI EN 300 019-1-2 Class 2.3)

- Temperature controlled enclosed location: -5°C to 45°C (ETSI EN 300 019-1-3 Class 3.2)
- Relative humidity: 5% to 95% (ETSI EN 300 019-1-3 Class 3.2)
4.3.1.3 Hardware description
4.3.1.3.1 Phone layouts
Although there are differences in the aspect and operation of these sets, their layout is
identical, but for the screen and number of available soft keys.

Figure 4.3: 8068 Premium DeskPhone set layout

 !"#!$% & '#! & ( ) "#!* &             65/160
  
Chapter 4    % 

Figure 4.4: 8038 Premium DeskPhone set layout

66/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

Figure 4.5: 8028 Premium DeskPhone set layout

4.3.1.3.2 Embedded hardware

A BCM1103 CPU is included in all IP DeskPhones sets.
32 Mb RAM (DDR1), 32 Mb Flash (NOR).
4.3.1.3.3 Foot stand
All sets come with a 0° to 60° adjustable foot stand.
4.3.1.3.4 Audio, handsets, hands free and headset
All sets come with a standard 3.5mm jack to plug a headset.
All sets offer wide band audio qualities (G722 codec is set as the default codec for 80x8)
Note 1:
The wide band capability is not available with the Bluetooth handset.
All sets come in their standard version with a comfortable corded handset.
They all work in hands free mode at the user's request.
The 8068 Premium DeskPhone with Bluetooth set can be equipped with a Bluetooth handset.
When this is the case, a Bluetooth charger interface is embedded in the set itself.
Note 2:

 !"#!$% & '#! & ( ) "#!* &             67/160
  
Chapter 4    % 

The Bluetooth handset with reference BTHS-2 is compatible with the 8068 Premium DeskPhone with
Bluetooth set.

4.3.1.3.5 Screens
Characteristics of set displays are:
- 8068 Premium DeskPhone: Thin Film Transistor (TFT) color graphical display of 240x320
dots, in 16,7 M colors, with Liquid Crystal Displays (LCD) Modules (LCM).
- 8038 Premium DeskPhone: black and white graphical display of 160 by 100 dots, with
white backlight
- 8028 Premium DeskPhone: black and white graphical display of 64 by 128 pixels with
white backlight
4.3.1.3.6 Keys
Dialing keypad
All sets come with a standard 12-key dialing keypad.
Fixed keys
On all sets:
- Two fixed keys below the keypad (start call key: and stop call key: ) allow to
perform several actions
The start call key operates as follows:
• In SIP survivability mode (applicable for IP phones):
• When the terminal is idle, a short press triggers the display of a dial out list on the
screen (same action as a long press on the redial key)
• When there is an incoming call, pressing the start call key puts the set in hands
free mode
• In NOE mode the start call key puts the set in hands free mode
The stop call key allows to end a call and ignore an incoming call
- A four-direction set of navigation keys (left, right, up, down) allows to select the different
options available on the screen. The OK button in the center of the navigation validates the
selection.
- The c key to the left of the navigation allows to cancel the current action.
- Sensitive (piano) keys are located above the black grid of the lower part of the set.
Starting from the left to the right, they provide access to the following features:
• mute sound

• decrease sound volume

• increase sound volume

• put loudspeaker in service

• hold call. This is the default feature for F1 keys (but can be programmed with
another feature)

68/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

• transfer call. This is the default feature for F2 keys (but can be programmed with
another feature)
redial information

• information page (displayed on screen)

• messaging services

Integrated additional programmable keys

On 8028 Premium DeskPhone sets, four add-on keys, each with a LED, allow to customize
each set according to the user's needs. A paper label at the right of these keys allows to write
down a brief description of the feature programmed on the key.
4.3.1.4 Connecting optional equipment
4.3.1.4.1 Alphabetic keyboard
A standard (hot pluggable) optional keyboard is available for all sets, in the following layouts:
- Azerty (FR)
- Qwertz (DE)
- Qwerty (international)
- Qwerty (Nordic)
If you change keyboard types, ensure it is plugged in before restarting the set.
4.3.1.4.2 External interfaces
On all sets, a 3.5mm jack connector allows to plug a headset to the phone.
The 8068 Premium DeskPhone with Bluetooth set, equipped with Bluetooth handset, includes
a Bluetooth charger interface.

Figure 4.6: External interfaces on the back of 80x8 sets

 !"#!$% & '#! & ( ) "#!* &             69/160
  
Chapter 4    % 

4.3.1.4.3 Additional key modules

On all sets, several add-on modules, connected via SATA (see: External interfaces ), can
complete the standard number of programmed keys.
Note:
- These add-on modules are not compatible with 40x8 and 40x9 phone sets.
- Add-on key modules designed for 40x8 and 40x9 phone sets are not compatible with IP DeskPhones
sets.
The available modules are:
- 10-key module (can be fastened to the set):

- 40-key module (on its own foot stand, placed next to the set)

- Smart-key module (on its own foot stand, placed next to the set)

70/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

4.3.2 Commissioning
4.3.2.1 Connecting the set
To connect the set to the PBX:
1. Plug the RJ45 cable into the set LAN connector
2. Connect the RJ45 cable to the LAN itself
3. If your set is not powered by PoE, plug the AC/DC external adapter to the set power supply
connector and connect the plug to the power supply
Once the set is connected and powered up, it automatically starts initializing.
4.3.2.2 Commissioning a Bluetooth® handset
The use of the 8068 Premium DeskPhone with Bluetooth or without Bluetooth can be detected
(in OMC (Expert View): Subscribers/Basestations list > Device details > Susbscriber tab)
as follows:
- For a 8068 Premium DeskPhone with Bluetooth set: the Terminal option “8068 Premium
DeskPhone” is displayed in Original Type field.
In this deskphone type, bluetooth option is available in the phone menu (Settings > My
Phone)
- For a 8068 Premium DeskPhone without Bluetooth set: the Terminal option ”8068
Premium DeskPhone – no BT” is displayed in Original Type field.
In this deskphone type, bluetooth option is not available in the phone menu.
Caution:
Bluetooth handsets are available for 8068 Premium DeskPhone with Bluetooth sets only. The
handset with reference BTHS-2 is compatible with 8068 Premium DeskPhone with Bluetooth sets.

 !"#!$% & '#! & ( ) "#!* &             71/160
  
Chapter 4    % 

Figure 4.10: Bluetooth handset ergonomics

4.3.2.2.1 Connecting the battery

The battery pack is housed in the battery compartment located in the handset.
The battery pack is reloaded when the handset is placed on its socket. A complete battery load
requires 16 hours.
The autonomy of the battery is of 10 hours in conversation and 33 hours in standby.
The handset Led indicates the battery load state (when the handset is on its socket):
- Led off: the battery is loaded
- Led green steady: the battery is loading
4.3.2.2.2 Binding the handset
Before a Bluetooth® handset can be used, it must be bound correctly to the set:
1. On the 8068 Premium DeskPhone with Bluetooth set, select the Menu page and navigate
to: Settings -> My phone -> Bluetooth -> Add device
2. On the Bluetooth® handset make a simultaneous long press on the On/Off Hook key and
the Audio key
A sound made of three different tones is audible and the led flashes alternatively green
and orange. The Bluetooth® handset enters in pairing mode for about one minute and then
goes off. The set searches for Bluetooth® equipment, waits until the type of equipment is
detected and displays its address.
3. On the set, select the relevant equipment and press the Add key.
A sound made of three different tones confirms the correct installation of the handset. The
handset led flashes green or orange depending on the battery charge.
4.3.2.2.3 Adjusting audio level
There are two ways to adjust the audio level:
- On the set with the keys

- On the Bluetooth® handset with the key

72/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

Consecutive presses adjust the handset volume (3 levels).

4.3.2.2.4 Activating the mute feature
When the mute feature is enabled your correspondent can no longer hear you.
There are two ways to activate the mute feature:
- On the set with the mute key

- On the Bluetooth® handset with a long press on the key

4.3.2.3 Connecting an add-on module to the sets

Add-On Modules (AOMs) can be connected to sets. They are added to the right side of the
set.
Three types of Add-On Module exist and provide keys associated with icons:
- AOM10 provides 10 keys
- AOM40 provides 40 keys
- Smart Display Module provides 14 keys with programmable LCD labels
4.3.2.3.1 Rules and restrictions
The following rules apply to the use of Add-On Modules:
- A maximum of three Add-On Modules of the types AOM10 and AOM40 can be connected
to each set, providing up to 120 additional keys.
- A maximum of three Smart Display Modules can be connected to each set, providing up to
42 additional keys.
- Add-On Modules of types AOM10 and AOM40 can be used on the same set, but a Smart
Display Module cannot be used in conjunction with an AOM10 or AOM40.
- If an AOM10 is used with other Add-On Modules, it must be connected as the last module
on the far right of the set.
4.3.2.3.2 Connecting add-on modules
To connect an Add-On Module:
1. Remove the tab located on the right side of the set.
2. Plug the Add-On Module's SATA connector into the set's SATA connector.
3. Insert the Add-On Module attachments into the appropriate holes located on the right side
of the set. (AOM10 only)
4. Screw the Add-On Module to the set. (AOM10 only)
Note:
If the set is on when you plug in an Add-On Module, you must restart the set after connection.

4.3.2.4 Set initialization

By default, 80x8 sets initialize dynamically and retrieve IP information automatically.
You can change this initialization mode by selecting IP parameters in the configuration menu,

 !"#!$% & '#! & ( ) "#!* &             73/160
  
Chapter 4    % 

which you must access as soon as the set is powered up. Static initialization is mandatory
when the system does not use a DHCP server.
4.3.2.4.1 Requested IP parameters
The following information must be provided for static initialization:
- IP address (set's address)
- Subnetwork mask
- Router address
- TFTP1 server address (see below for special configurations)
- TFTP2 server address (if needed, see below)
- Use VLAN: this box must be checked to enter a VLAN number
- VLAN number if necessary
- Strict VLAN if necessary
- TFTP port
The TFTP address(es) to enter may differ according to system configuration.
Please contact your system administrator for details on the configuration of your system.
Duplication Conditions TFTP1 Address TFTP2 Address
The Com Server is not duplicated Com Server main IP N/A
address (or Com
Server physical ad-
dress if no main IP
address has been
configured)
In a duplicated Com Server configuration Com Server main IP N/A
where the two Com Servers are on the same address
subnetwork
In a duplicated Com Server configuration Com Server A main Com Server B main
where the two Com Servers are on different IP address IP address
subnetworks

With dynamic initialization, IP parameters are automatically sent by a DHCP server to the
phone.
The following information must be provided for initial startup:
1. From the Registration window, enter:
a. The set directory number
b. The set Password
If the set has already been initialized in the same configuration, there is no need to enter the
directory number and password again.
4.3.2.4.2 Deny of download
If the downloaded version is different from the version installed on the set and if the
downloaded binary is incompatible with the hardware/software, the terminal denies it and
signals the problem to the Call Server.

74/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

The terminal requests binary files at each reset until a compatible binary is found.
Deny of download also applies to SIP binary.
4.3.2.5 Binary file download
To operate correctly, 80x8 sets require binary files, automatically downloaded at set
initialization. These files must comply with the PBX version and configuration. After system
upgrade and each time a set initializes, version numbers of binary files are verified to
determine whether an update of these files is necessary.
When a file is downloaded to the set, it overwrites any previously existing file.
Each time the IP phone is initialized, its binary version is checked to see whether more recent
binaries need downloading.
When a set has initialized at least once with the PBX, on subsequent startup, it does not
request a binary header and switches to fast initialization.
The version of binary files for Premium DeskPhone sets. starts with 4.50.YY

4.3.3 Maintenance for 80x8

4.3.3.1 Error and Information messages
The table below lists the error and information messages. It has the following format:
Short text = text displayed on the screen, in case of real error or for information.
Description = status/error description
table 4.4: Starting phase error messages
Short text Description
END Starting phase is terminated (successful or
unsuccessful)
STARTED Step started
SUCCESS Step successful
FAIL Step failed
RETRYING Retrying step
NO MAC ADDRESS No Ethernet MAC address stored in flash
DHCP NOT RESPONDING DHCP Server is not responding
BAD IP ADDRESS IP address is incorrect
BAD ROUTER ADDRESS Router address is incorrect
ROUTER PING FAILED Router not responding to ping
BAD TFTP ADDRESS TFTP server address is incorrect
ADDRESSES MISMATCH Address, mask and router do not match
TFTP NOT RESPONDING TFTP server is not responding
TFTP SERVER ERROR TFTP server error
BAD FILE CONTENT Error found in downloaded file
FILE TOO LARGE File is too large (cannot be downloaded)

 !"#!$% & '#! & ( ) "#!* &             75/160
  
Chapter 4    % 

Short text Description

SAME VERSION FOUND The version retrieved is the same as the ver-
sion running
NEW VERSION FOUND New IP Touch software version found
(download)
FLASHING Flashing in progress
FLASHING FAILED Failed to flash downloaded binary
TRYING ANOTHER CPU Trying next address from configuration file
NO ETHERNET LINK Ethernet link not connected (LAN port only)
initializing First text message after hardware reset and
copyright information
1/5 network start Phase 1 is running: the set is starting its net-
work interface
2/5 network setup Phase 2 is running: the set is looking for IP
addresses
3/5 config download Phase 3 is running: the set is trying to get a
lanpbx file
4/5 binary download Phase 4 is running: the set is downloading a
new binary
5/5 connecting Phase 5 is running: the set is trying to talk to
the system

4.4 8082 My IC Phone

4.4.1 Basic description

4.4.1.1 Overview
The 8082 My IC Phone set is a full-featured SIP device which constitutes a new step in the
implementation of user needs and comfort.

76/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

Its screen is a 7 inch capacitive LED backlit touch screen, which provides a context sensitive
feedback, easing the tasks of users.
Access to the most common features is facilitated by a quick access pad, where a sensitive
home key brings you to the homepage. The other sensitive similar keys pilot your audio
volume and provide access to your main applications.
Its audio quality is outstanding and welcomes:
- Corded comfort handset or Bluetooth® handset (or headset)
- High quality loudspeaker
- Handsfree feature with high fidelity audio quality
An open connectivity supports easy expansion with a 10/100/1000 Ethernet switch for LAN
and PC connectivity, an embedded Bluetooth® chipset, a 3.5 mm headset port, two USB
connectors, as well as connectors for keyboard and handset.
4.4.1.2 Video architecture
The 8082 My IC Phone sets includes features that support video capabilities for:
- Video calls
- Door management
A Logitech webcam can be added to the 8082 My IC Phone set as part of the interactive
hardware for the video feature.

 !"#!$% & '#! & ( ) "#!* &             77/160
  
Chapter 4    % 

Video calls can be configured for:

- 8082 My IC Phone over a SIP trunk

- Other SIP phones with video capabilities

78/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

Door management with the 8082 My IC Phone and a door camera is available with the Link
Slim IP Door Phone

4.4.2 Hardware description

4.4.2.1 Set Equipment
The 8082 My IC Phone set includes the following items:
- Bluetooth® Handset with a front LED or Corded comfort handset
- Hands-free station speaker
- A quick access pad (which includes LEDs)
- A set screen, which is adjustable from the typical angle of 60° relative to the table surface,
to a near horizontal position
4.4.2.2 Quick Access Pad LEDs
LEDs are lit for each active feature displayed, regardless of the status (idle, busy) of the set.
Touching a LED activates/deactivates the corresponding feature.
The table below indicates the default meaning of LEDs. Note that this meaning can depend on
the application active on the set.
LED Corresponding Feature
Mute

Volume down

Volume up

 !"#!$% & '#! & ( ) "#!* &             79/160
  
Chapter 4    % 

LED Corresponding Feature

Hands-free

User information, presence and call routing configuration (including

Do not Disturb)

Communications

Dial/Search

Events

Home

4.4.2.3 Set Screen

The LCD set screen is touch sensitive.
When buttons are displayed, touch any button to activate a feature (or display the
corresponding window).

Figure 4.16: 8082 My IC Phone Screen Example

80/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

Figure 4.17: Example of Home Page

When a list is displayed, either horizontally or vertically, touch the screen and move your finger
in the desired direction. The display reacts according to the direction of your finger movement.

Figure 4.18: 8082 My IC Phone Screen List Example

4.4.2.4 Video accessories

Note:
Video compatibility is only available for the 8082 My IC Phone HW2 and later. HW1 sets are not video
compatible.
The 8082 My IC Phone can be used in conjunction with a video hardware to provide

 !"#!$% & '#! & ( ) "#!* &             81/160
  
Chapter 4    % 

capabilities for:
- Video calls
- Door management support
The Logitech C920 can be connected directly to the 8082 My IC Phone via the USB
connection.

Figure 4.19: Logitech C920 webcam

Features for the Logitech C920 include:
- Wide view field
- Omni-directional microphones
- High quality Zeiss lens
- Plug-and-play with most video conferencing and UC applications
The Link Slim IP Door Phone can provide the exterior camera and bell push for the door phone
application used with the 8082 My IC Phone. It is an IP based phone that is linked to the OXO
Connect and can be used to manage entry access.

82/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

Figure 4.20: Link Slim IP Door Phone

The Link Slim IP Door Phone uses a single cable to use the PoE capabilities to control door
entry from a computer or IP telephone. Features include:
- Voice & Image based on Full SIP protocol
- Autofocus IP Camera
- White LED for automatic lighting for camera
- PoE technology or Power supply 12 V AC/DC, 500 mA max
- Ethernet - 10/100 MB SIP connection P2P or PBX network system
- Day/night switching feature

4.4.3 Commissioning
4.4.3.1 Overview
This module presents all the actions required for commissioning the 8082 My IC Phone sets.

 !"#!$% & '#! & ( ) "#!* &             83/160
  
Chapter 4    % 

Figure 4.21: 8082 My IC Phone set layout

The following figure illustrates the connectors on the base of each set.

84/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

Figure 4.22: 8082 My IC Phone set connectors

4.4.3.2 Commissioning the set

This section describes how to commission the set in the two available initialization options:
- Static initialization: commissioning is manual on the set and through OMC
- Dynamic initialization (DHCP): no commissioning is needed, 8082 My IC Phone sets are
fully plug & phone
Depending on the selected mode, the set commissioning is different.
For static initialization, the operation order is as follows:
1. Connect the set, refer to Connecting the set
2. Configure network parameters on the set, refer to Configuring network parameters for
static initialization
For dynamic initialization, the operation order is as follows:
1. Configure OXO Connect DHCP server, refer to Configuring OXO Connect DHCP server ,
or configure an external DHCP server, refer to Configuring an external DHCP server for
dynamic initialization

 !"#!$% & '#! & ( ) "#!* &             85/160
  
Chapter 4    % 

2. Connect the set, refer to Connecting the set

3. If necessary, configure the user name and password in OMC, refer to Configuring the user
name and password in OMC
4.4.3.2.1 Prerequisites
- The OXO Connect must be operational
- For network configuration, any of the following must be implemented:
• In dynamic mode, a DHCP server must be configured
• In static mode, a free IP address must be available for the set
- A port with PoE must be available on a switch. If not available, a PoE injector must be
used
4.4.3.2.2 Connecting the set
This section describes how to:
- Connect an 8082 My IC Phone set to the LAN (Local Area Network)
- Connect the external power adapter, if necessary
Note:
The external power adaptor is compatible with 8082 My IC Phone HW2, it is not compatible with version
HW1.

Connecting an 8082 My IC Phone set to the LAN

To connect the set to the LAN:
- If you are using the 8082 Power Over Ethernet Injector Kit:
a. Plug an RJ45 cable between the data in port of the kit and the LAN
b. Plug an RJ45 cable between the data and power out port of the kit and the set LAN
connector
c. Plug the kit to the mains
- If you are not using the 8082 Power Over Ethernet Injector Kit, plug an RJ45 cable
between the set LAN connector and a port of the switch
Connecting power supply

Note:
Only available for 8082 My IC Phone HW2
If you are not using a PoE switch or the 8082 Power Over Ethernet Injector Kit, connect the
AC/DC external adapter:
1. Plug the appropriate cable from the adapter into the set's power supply connector.
2. Connect the plug from the adapter to the mains power supply.
4.4.3.2.3 Initializing the sets
The following sections describe how to:
- Select the initialization type
- Initialize the 8082 My IC Phone set

86/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

Selecting the initialization type

The default initialization is Dynamic Alcatel.
To select the initialization type, refer to the following table.
table 4.6: Initialization type selection
If Then the required ini- Further information
tialization type is
You use OXO Con- Dynamic or Proprietary - Refer to Configuring OXO Connect DH-
nect DHCP server Dynamic CP server
You use another DH- Dynamic - Refer to Configuring an external DHCP
CP server server for dynamic initialization
You do not use a DH- Static - Refer to Configuring network parameters
CP server for static initialization
- Obtain from your network administrator:
• An IP address for the 8082 My IC
Phone set
• The subnetwork mask
• The router address
• The DNS addresses (primary and
secondary)
• The VLAN ID (if VLAN is used)
• The IP address of the OXO Connect
for set configuration file download
Note:
You need to know the set directory number.

Configuring OXO Connect DHCP server

The OXO Connect DHCP server is enabled by default during startup wizard installation. If
enabled, 8082 My IC Phone sets automatically initialize in dynamic mode, when plugged to the
OXO Connect. In other words, 8082 My IC Phone sets automatically get their IP configuration
from the OXO Connect DHCP server
If the OXO Connect DHCP server is disabled, you can enable it as follows:
- In OMC, go to Hardware and Limits > LAN/IP Configuration > DNS/DHCP.
- In the ALU IP Phones: DHCP IP Range area, select the Enable check box.
- Modify the range of IP addresses if needed.
- Click the OK button to confirm your entries.
Configuring an external DHCP server for dynamic initialization
Two types of dynamic initialization are available:
- Dynamic (default value): the set selects in priority DHCP offers, with a Vendor Specific
option corresponding to an ALE International server.
- Proprietary Dynamic: the set accepts only DHCP offers with a Vendor Specific option
corresponding to an ALE International server (alcatel.int-ip.0, alcatel.a4400.0,
alcatel.a4200.0).

 !"#!$% & '#! & ( ) "#!* &             87/160
  
Chapter 4    % 

When initializing in dynamic mode, the set provides the following information in the DHCP
Discover message
- Option 60: (vendor class identifier): alcatel.ictouch.0
- Option 55: list of requested options: subnet mask, router option, broadcast address, option
43 vendor specific info, server ID, renewal time, rebinding time and vendor class ID
Option 43 is vendor specific information, meaning that this option is defined for a specific client
vendor ID. In the DHCP offer, the data within Option 43 corresponds to the client vendor ID
specified in the request.
In the case of 8082 My IC Phone sets, suboption 67 of option 43 provides the path of
configuration files on the OXO Connect.
The DHCP offer provides the following parameters:
- IP address
- Router IP address
- Subnet mask
- Option 66: IP address:10443 or name of the OXO Connect:10443, for example
192.168.12.34:10443
- Suboption 67 of option 43: the value of this sub-option corresponds to the DM Url.It must
contain a string value set to /dmcfg/
- Option 58: VLAN ID: this is sent as a suboption of option 43
Optionally, the DHCP offer can include the following parameters, which can also be configured
locally on the terminal or on the OXO Connect:
- Option 6: Domain Name Server (DNS primary and secondary)
- Option 15: Domain name
- Option 12: Host name (eg, ICTouch<MAC>)
- Option 42: SNTP server
- Option 120: SIP server (outbound proxy server address or name)
Configuring network parameters for static initialization
MMI allows to access and configure the following parameters (you must have administration
rights to modify static configuration):
- In the Network menu:
• DM (OXO Connect) URL: https://OXO Connect IP address:10443/dmcfg/
• DNS addresses
• Ethernet parameters: the LAN and PC Ethernet interfaces are by default configured in
auto-negotiation mode
• IP parameters
• Log parameters, allowing to define a syslog server for log reception
• Network parameters, allowing to:
• Enable and configure a DHCP User Class: this makes the set send the standard
DHCP option 77 (User Class, RFC2132) within the DISCOVER and REQUEST
DHCP messages. Using this option allows to define groups of terminals, and to
attach these groups to different and independent Com Servers.

88/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

• Define an SNTP Server address and refresh period

• Proxy host and port
• SIP parameters (read only)
- In Security menu:
• 802.1x parameters
• Certificates: not used
4.4.3.2.4 Configuring the user name and password in OMC
The user default password for a new user is defined at first installation. If need be, the
administrator can reset the user default password via the OMC
To modify the name and reset the password:
- In OMC, go to Users/Base stations List.
- To modify the user name: click the user in the list, modify the user name in the
corresponding field and click Modify
- To reset the user password:
• Click the user in the list and click Details to open the User window
• Click Password to open the Password window
• Click Reset to reset the password
Note:
At reset, the password is set to the user default password value defined at first intallation.
4.4.3.2.5 Voice mail access
Using the IcsMessaging Web Service, a voice communication is automatically established
between the 8082 My IC Phone set and the VMU to:
- Manage the messages (play, pause, stop)
- Delete one or all messages
- Record, send or cancel a new message
A VMU password can be required to access the voice mailbox from the local voice mail
application. The IcsUserProfile Web Service is used for password verification.
Note:
Password authentication is only requested when the parameter is validated
To validate password requirement:
In OMC:
1. Select Voice Processing
2. Select General Parameters
3. Verify Password required for mailbox consultation
4.4.3.2.6 Connecting optional equipment
Headsets
A headset can be used with 8082 My IC Phone sets.

 !"#!$% & '#! & ( ) "#!* &             89/160
  
Chapter 4    % 

By default the set is configured to detect headset connection. When the headset is plugged in,
the audio is sent to the headset. The hands-free key allows you to switch from handset,
headset and hands-free.
A Bluetooth® headset may be used.
If your headset is wired, plug it to the associated set connector (see: figure: 8082 My IC Phone
set connectors ), which can be any of the following:
- The jack plug
- The set USB port
External station speakers
Any connector used for a headset can be used for external speakers.
Customize your set to take the external station speaker into account:
1. Touch the Settings button
Note:
According to system administration, this button may not appear. The availability of this option is
determined by the set configuration files. Contact your telephony and/or system administrator.
2. Select Devices > Audio
3. Select the connection of your choice (from Accessory device to Bluetooth® device)
4. Touch the field to access available values
5. Select Loudspeaker
6. If your device is not Bluetooth®, plug it to the corresponding connector
Traffic priority on the internal switch
The 8082 My IC Phone set includes an internal LAN switch.
This switch allows to connect a PC.
The internal switch has three ports:
- A LAN port
- An internal port
- A PC port, to connect a PC to the LAN.
The internal switch privileges VoIP traffic over PC port traffic.
This switch has two waiting queues:
- The HPQ (High Priority Queue) to proceed all packets from the terminal
- The LPQ (Low Priority Queue) to proceed packets from the PC port
The switch proceeds seven HPQ packets for an LPQ packet.
Exception: packets from the PC port use the HPQ when they are tagged with a DSCP or
802.1p priority and when the priority value is superior or equal to 4.
4.4.3.2.7 Resetting user data
To reset user data:

90/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

1. In OMC, go to Users/Base stations List > Details.

2. Click Reset.
The Reset window opens.
3. Select Reset User Data and click OK.
4. In the confirmation window, click Yes.
4.4.3.2.8 Rebooting an 8082 My IC Phone set
To reboot a set:
1. In OMC, go to Users/Base stations List > Details.
2. Click Reset button.
The Reset window opens.
3. Select Reboot and click OK.
4. In the confirmation window, click Yes.
4.4.3.2.9 Displaying SIP connection current status
This feature allows the display of SIP connection status.
To display SIP connection status:
1. In OMC, go to Users/Base stations List > Details.
2. Read the SIP connection status (under the terminal's physical status).
The following table lists the different displayed status.
table 4.7: SIP connection status display
Displayed Status Meaning
Set not connected SIP phone disconnected from network / No
SIP registration request from the phone
SIP registration KO SIP registration request from SIP Phone rejec-
ted by OXO Connect
Set unregistered SIP phone unregistered from OXO Connect
SIP registration OK SIP phone connected and successfully re-
gistered to OXO Connect

4.4.3.2.10 Terminal conference

8082 My IC Phone sets can handle their own local conference, involving up to 2 external
members. In this case, conference is not handled at call server level and the Conference
parameter configured in System Miscellaneous > Feature Design > Part 3 does not apply.
4.4.3.3 Ringing parameters
The set user can select different ringing tones for the different types of call or event.
To configure ringing tones:
1. Touch the Settings button

 !"#!$% & '#! & ( ) "#!* &             91/160
  
Chapter 4    % 

Note:
According to system administration, this button may not appear. The availability of this option is
determined by the set configuration files. Contact your telephony and/or system administrator.
2. Select Devices > Audio
3. Review/modify the following parameters:
On-site ringing Select the ringing for external calls
Off-site ringing Select the ringing for internal calls
Event ringing Select the ringing for calendar events
Special ringing Select the ringing indicating that the Bluetooth® handset is out of
range

4.4.3.4 Video call parameters

The OmniPCX Management Console (OMC) is used to enable the video call support for the
8082 My IC Phone sets. Once configured it is possible to make:
- Basic P2P video calls between 8082 My IC Phone (VHE-2) and any SIP phone with video
support.
- Basic video calls from 8082 My IC Phone (VHE-2) over a SIP trunk
The configuration for video is carried out in two steps:
1. Generic SIP phone parameters for video calls are verified and modified if necessary, see
Generic video parameters
2. Each set is enabled, see Enabling video support for a 8082 My IC Phone set
4.4.3.4.1 Generic video parameters
The parameters in the table are generic (common) to all 8082 My IC Phone sets. They are
accessed from:
OMC -> Subscribers Misc -> Generic Parameters for SIP Phones -> Video Call
parameters
Video Camera Country Frequency: defines the vertical scan frequency which is needed to
avoid flickering of video. This is same as the mains power frequency of the country. Default
value for this parameter is kept based on the target type (country) of the OXO Connect.
Country Type Video Camera Country Fre-
quency (Default value in
OMC)
Brazil Costa-Rica Guatemala Haiti Honduras Mexico Panama 60 Hz
Philippines Saudi Arabia Taiwan USA Venezuela Verizon
All others 50 Hz

Video Camera Refresh Cycle: defines the time interval between two full pictures refresh in
seconds. This parameter impacts the network bandwidth usage.If the value of this parameter
is 0, it indicates no refresh.
Video Differential Services: indicates the value of ‘Differential Services’ field in the IP header.
Video 802.1p: indicates the value of ‘802.1p’ field in the IP header.

92/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

Video Call Profile Level ID: indicates the value of ‘SDP’ field in IP header. This parameter
encodes in it, the information on profile, level and ID for video call encoding.
Video Call Encoding Profile: defines the profile that 8082 My IC Phone must use for video
stream encoding. This impacts the quality of the video.
Video Encoding Profile Low/Medium/High: defines the bandwidth used for low/Medium/High
level video encoding profile in kbps.
Video Call Packetization Mode: defines packetization mode (PM) among 3 values:
PM1 provides best quality video with reduced bandwidth. If the distant set does not support
PM1, PM0 is used. PM0 should be avoided since it is not well supported on 8082 My IC
Phone. NS is for exclusive use of PM1. If NS is not supported by the distant, negotiation fails
(no video)
All the video configuration parameters and their possible values are described in table: Video
parameters
table 4.10: Video parameters
OMC Parameter Common/Specif- Default Value Possible Values
ic to 8082 My IC
phones
Video Support Specific to Ter- Enabled Enabled/Disabled
minal
Video Camera Country Fre- Common Based on target 50 Hz / 60 Hz
quency country
Video Camera Refresh Cycle Common 2 [0 .. 2160]
Video Differential Services Common 5 [ 0 .. 63 ]
Video 802.1p Common 5 [0 .. 7]
Video Call Profile Level ID Common 0x42801E [0...0xFFFFFF]
Video Call Encoding Profile Common Medium Low/Medium/High
Video Encoding Profile Low Common 256 kbps 0 .. 65535]
Video Encoding Profile Medium Common 1000 kbps [0 .. 65535]
Video Encoding Profile High Common 2500 kbps [0 .. 65535]
Video Call Packetization Mode Common PM0 PM0 / PM1 / NS

4.4.3.4.2 Enabling video support for a 8082 My IC Phone set

The Video Support feature right is specific to each 8082 My IC Phone set. Video telephony is
enabled or disabled specifically for each set.
Note:
Enabling is mandatory to support Video calls (incoming or outgoing) for 8082 My IC Phone sets.
To enable/disable “Video Support”
OMC -> User/Base stations List -> 8082 MY IC Phone-> Details-> Features -> Feature
Rights -> Part 1
Video support: select the check box to allow video support on the 8082 My IC Phone.
4.4.3.5 SIP door phone parameters

 !"#!$% & '#! & ( ) "#!* &             93/160
  
Chapter 4    % 

Note 1:
If SIP door phone management is to be done with video support, refer to Video call parameters to enable
video.
The generic parameters for SIP door phone management with 8082 My IC Phone can be
modified at
OMC -> Subscribers Misc -> Generic Parameters for SIP Phones -> Door Phone
Parameters
OMC Parameter Common/Specific Default Value Possible Values
to 8082 My IC
phones
Door Phone Name Common Doorcam STRING
Door Open Signal Common 55 STRING

Door Phone Name: defines the name that must be given for all SIP door phone terminals.
Default value for this parameter is 'Doorcam'.
The unique name defined with ‘Door Phone Name’ parameter is used by 8082 My IC Phone to
identify calls from SIP door phones.
Note 2:
The 'Door Phone Name’ parameter is case sensitive. SIP door phone names must be unique and not the
same as the ‘Door Phone Name’ parameter.
Door Open Signal: defines the DTMF code that is sent from 8082 My IC Phone to SIP door
phone to open the door latch. The default value for this parameter is 55.
4.4.3.6 Upgrading the software
The Alcatel-Lucent OmniTouch™ 8082 My IC Phone set software is upgraded during OXO
Connect software upgrade. Ensure the 8082 My IC Phone option is validated in the
OMC-Software Download window: refer to the section Downloading the Software in
document [11].

4.4.4 Reset to factory

4.4.4.1 Overview
The reset to factory is intended to cope with situations in which the administrator can no longer
access the set configuration because the set administrator password has been lost, and the
set is configured in static mode or uses a specific VLAN on the previous installation. Reset to
factory is not needed when a set is configured in dynamic mode: in this case, the set
administrator password can be changed through the device management tool.
The reset to factory enables to restore the set to the “Out of the box” initial status, except that
the software version remains unchanged on the set. It works during the set initialization. If
initialization is done, there is no other solution to reset sets to their factory settings.
The reset to factory performs the following actions:
- Restore the set administrator password to its default value
- Clean all user data and webapps
- Restore the configuration and settings to their default values

94/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

- Remove certificate data such as customer certificates and CTL, except ALE International
default certificate stored during manufacturing
- Store a message into Defense log to indicate a reset-to-factory has been done
- Reboot
Note:
Although the feature is not intended for end-users, it is available in user mode, as this feature is used
when the set administrator password has been lost, and therefore the administrator mode cannot be
reached.
It is not possible to limit the availability of the feature for users and/or administrators by setting the
appropriate display-rights to the setting EnableResetFactory in the third configuration files, generated
by the Customizer.

4.4.4.2 Procedure
To perform the reset to factory on a set:
1. Restart the set
2. During set initialization (step 2 or 3), press Settings
3. Select Device > Reset

4. Set the Reset to factory option to Yes

Your are prompted to enter the administrator password required for the reset to factory.
The default administrator password is *tx8000#.

 !"#!$% & '#! & ( ) "#!* &             95/160
  
Chapter 4    % 

5. Enter the administrator password, then press OK to confirm the reset to factory, or press
Cancel to cancel the reset.
• If the password is WRONG or Cancel is pressed; the set displays again the reset
screen, the choice selector is set to NO: without further action, the set will go on with
normal startup.
• If the password is VALID, you are prompted to confirm the action:

6. Press Yes to confirm the reset to factory: reset to factory is performed and the set restarts
immediately.
Press No to cancel: the set displays again the reset screen, the choice selector is set to
NO: without further action, the set will go on with normal startup.

4.5 4135 IP Conference Phone

4.5.1 Basic description

4.5.1.1 Overview

96/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

The 4135 IP Conference Phone is a conference phone for IP telephony offering a host of
innovative features:
- OmniSound® 2.0 audio technology
- IP telephony for flexible and affordable telephony
- Management of lines during a call (calling new parties, creating a multi-party call, splitting a
multi-party call)
- Recording capability (requires an optional SD Card)
- Web interface for simple management of contacts, conference groups and settings (only
available in English language)
- Extra microphone connection for wider reception (option)
- Connection for wireless headset or PA system (option)
- Future-proof, can be upgraded with smart functions

4.5.2 Hardware description

4.5.2.1 Keypad

 !"#!$% & '#! & ( ) "#!* &             97/160
  
Chapter 4    % 

Figure 4.27: 4135 IP Conference Phone Keypad

Each button provides access to letters and characters - including characters not shown on the
button. Press the same button repeatedly to use another character. To enter several letters
accessible from the same button one after the other, pause before entering the second letter.
Press C to delete the last character you have entered.
4.5.2.2 Display Screen

98/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

Line free (Before account name – telephone not registered)

Line connected (Before account name – telephone registered)
Line on hold (“HOLD” displayed on the screen – all calls on hold)
Line (called party) busy

Own line put on hold by other party

Recording call
Secure connection

4.5.3 Commissioning
4.5.3.1 Overview
This module presents all the actions required for commissioning 4135 IP Conference Phone
sets.

Figure 4.30: 4135 IP Conference Phone set layout

The following figure illustrates the connectors on the base of each set.

 !"#!$% & '#! & ( ) "#!* &             99/160
  
Chapter 4    % 

Figure 4.31: 4135 IP Conference Phone set connectors

The 4135 IP Conference Phone is a SIP device which has no handset; it is dedicated to be
used as central for conferences.
Conferences are not managed by the system, but by the device itself. Up to four 4135 IP
Conference Phones can be connected to the OXO Connect.
4.5.3.2 Commissioning the set
This section describes how to commission the set in the two available commissioning types:
- Static: commissioning is manual on the set and on OMC
- Dynamic (DHCP): the set automatically retrieves its IP address and other parameters from
a DHCP server (OXO Connect DHCP server or an external DHCP server) .
Complementary operations are necessary on the set and on OMC
For static commissioning, operations are:
1. Configure the user in OMC, refer to Configuring the user by OMC
2. Connect the set to the LAN, refer to Connecting the set to the LAN
3. Configure the network parameters on the set, refer to Configuring network parameters for
static initialization
4. Export the server certificate from the OXO Connect: refer to Exporting the server certificate
from the OXO Connect
5. Upload the certificate on the 4135 IP Conference Phone
For dynamic commissioning, operations are:
1. Configure OXO Connect DHCP server, refer to Configuring OXO Connect DHCP server ,

100/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

or configure an external DHCP server, refer to Configuring an external DHCP server

2. Connect the set to the LAN, refer to Connecting the set to the LAN
3. Configure the user name and password and consult the SIP password in OMC, refer to
Configuring the user name and password in OMC
4. Export the server certificate from the OXO Connect: refer to Exporting the server certificate
from the OXO Connect
5. Enter the SIP password through MMI, refer to Entering the SIP password through local
MMI
6. Upload the certificate on the 4135 IP Conference Phone
4.5.3.2.1 Prerequisites
- The OXO Connect must be operational
- For network configuration, any of the following must be implemented:
• In dynamic mode, a DHCP server must be configured
• In static mode, a free IP address must be available for the set
- A port with PoE must be available on a switch
4.5.3.2.2 Configuring the user by OMC
This paragraph applies to OMC configuration of sets initializing in static mode. In dynamic
(DHCP) mode, the following operation is not mandatory but the server certificate must be
exported from the OXO Connect to the PC and can then be uploaded to the 4135 IP
Conference Phone.
To create a 4135 IP Conference Phone:
1. In OMC, go to Users/Base stations List.
2. Select a No., IP access, enter a name and click the Add button.
3. Select IP terminal and click OK.
4. Select the newly created user in the list and select 4135 IP Conference Phone in the
combo box type.
5. Click the Modify button.
6. Click the newly created user to open the User dialog box.
7. Click the IP/SIP button and enter the MAC adress of the set in the IP Parameters tab.
8. If needed, in the SIP Parameters, click the SIP password reset button to get a new
password.
4.5.3.2.3 Connecting the set to the LAN

Note:
the set is supplied via Ethernet, so make sure using a 802.3af standard-compatible switch.
To connect the set to the LAN:
1. Turn the set over so that you can see its base.
2. Plug the RJ45 cable into the set's LAN connector.
3. Connect the RJ45 cable to the LAN.

 !"#!$% & '#! & ( ) "#!* &             101/160
  
Chapter 4    % 

4.5.3.2.4 Initializing the sets

This section describes how to:
- Select the initialization mode
- Initialize the 4135 IP Conference Phone set
Selecting the initialization type
The default initialization is Dynamic Alcatel.
To select the initialization type, refer to the table below.
table 4.13: Initialization type selection
If Then the required ini- Further information
tialization mode is
You use OXO Con- Dynamic or Proprietary - Refer to Configuring OXO Connect DH-
nect DHCP server Dynamic CP server
You use another DH- Dynamic - Refer to Configuring an external DHCP
CP server server
You do not use a DH- Static - Refer to Configuring network parameters
CP server for static initialization
- Obtain from your network administrator:
• An IP address for the 4135 IP Con-
ference Phone set
• The subnetwork mask
• The router address
• The DNS addresses (primary ans
secondary)
• The VLAN ID (if VLAN is used)
• The IP address of the OXO Connect
for configuration files download
Note:
You need to know the set directory number.

Configuring OXO Connect DHCP server

The OXO Connect DHCP server is enabled by default during startup wizard installation. If
enabled, 4135 IP Conference Phone sets automatically initialize in dynamic mode, when
plugged to the OXO Connect. In other words, 4135 IP Conference Phone automatically get
their IP configuration from the OXO Connect DHCP server.
If the OXO Connect DHCP server disabled, you can enable it as follows:
- In OMC, go to Hardware and Limits > LAN/IP Configuration > DNS/DHCP.
- In the ALU IP Phones: DHCP IP Range area, select the Enable check box.
- Modify the range of IP addresses if needed.
- Click the OK button to confirm your entries.
Configuring an external DHCP server
In Dynamic initialization (default value), the set selects the first DHCP offer, with a Vendor

102/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

Specific option corresponding to an Alcatel-Lucent server.

When initializing in dynamic mode, the set provides the following information in the DHCP
Discover message:
- Option 60: (vendor class identifier): alcatel.sip.0
- Option 55: list of requested options: subnet mask, router option, broadcast address, option
43 vendor specific info, server ID, renewal time, rebinding time and vendor class ID
Option 43 is vendor specific information, meaning that this option is defined for a specific client
vendor ID. In the DHCP offer, the data within Option 43 corresponds to the client vendor ID
specified in the request.
In the case of 4135 IP Conference Phone sets, suboption 67 of option 43 provides the path of
configuration files on the ALE International.
The DHCP offer provides the following parameters:
- IP address
- Router IP address
- Subnet mask
- Option 66: IP address or name of the OXO Connect:10443, for example
192.168.12.34:10443
- Suboption 67 of option 43: the value of this sub-option must contain a string value set to
https://alize/dmcfg/
- Option 58: VLAN ID: this is sent as a suboption of option 43
Optionally, the DHCP offer can include the following parameters, which can also be configured
locally on the terminal or on the OXO Connect:
- Option 6: Domain Name Server (DNS primary and secondary)
- Option 15: Domain name
- Option 12: Host name (eg, ICTouch<MAC>)
- Option 42: SNTP server
- Option 120: SIP server (outbound proxy server address or name)
Exporting the server certificate from the OXO Connect
1. Go to OMC->Import/Export->Export Server Certificate.
The Export Server Certificate window is displayed
2. Click Browse button.
The Exportfile window is displayed:
• The File name field indicates server.crt. The file name can be modified as needed
• The Files of type field indicates Certificate Files
3. Specify the destination path for the export and click OK: The selected path and the
certificate file name are displayed in the Export Server Certificate window
4. Click the Export button: The certificate file is exported from the OXO Connect to the
specified file path in PC
5. Click the Return button
Configuring network parameters for static initialization

 !"#!$% & '#! & ( ) "#!* &             103/160
  
Chapter 4    % 

The following parameters must be entered through the MMI:

- IP address
- Subnet mask
- Gateway address
- DNS addresses
- VLAN use
- VLAN ID (if VLAN use is set)
- URL: provides the URL on the OXO Connect to download configuration file. The path on
the OXO Connect is /dmcfg/
- SIP password
4.5.3.2.5 Configuring the user name and password in OMC
To modify the name and password:
- In OMC, go to Users/Base stations List.
- Click the user in the list.
- Modify the user name in the corresponding field and click Modify.
- Double-click the user in the list to open the User dialog box.
- Click on IP/SIP, go to SIP parameters tab to consult the SIP password.
4.5.3.2.6 Displaying SIP Connection Current Status
This feature allows the display of SIP connection status.
To display SIP connection status:
1. In OMC, go to Users/Base stations List > Details.
2. Read the SIP connection status (under the terminal's physical status).
The following table lists the different displayed status.
Displayed Status Meaning
Set not connected SIP phone disconnected from network / No
SIP registration request from the phone
SIP registration KO SIP registration request from SIP Phone rejec-
ted by OXO Connect
Set unregistered SIP phone unregistered from OXO Connect
SIP registration OK SIP phone connected and successfully re-
gistered to OXO Connect

4.5.3.2.7 Entering the SIP password through local MMI

For static and dynamic initialization, enter the SIP password through MMI.
4.5.3.3 Upgrading the software
The 4135 IP Conference Phone set software is automatically upgraded during OXO Connect
software upgrade (there is no specific option to select in the OMC-Software Download

104/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

window: refer to the section Downloading the Software in document [11]).

The 4135 IP Conference Phone set software can also be upgraded manually through the MMI.

4.6 Generic SIP Phones

4.6.1 Commissioning
4.6.1.1 Overview
This module presents all the actions required for commissioning generic SIP sets.
The List of supported SIP Phones is available on the Alcatel-Lucent Applications Partner
Program (AAPP) web site.
4.6.1.2 Commissioning Generic SIP Sets
This section describes how to commission a generic SIP Set.
The following operations must be performed:
1. Configure the user in OMC, refer to Configuring the User in OMC
2. Connect the set, refer to Connecting the Set and switch it on
3. Configure the generic SIP set, refer to Configuring the generic SIP set , or configure the
OXO Connect DHCP server, refer to Configuring OXO Connect DHCP server .
4.6.1.2.1 Prerequisites
- The OXO Connect must be operational
- A free IP address must be available for the set
- A port with PoE must be available on a switch
4.6.1.2.2 Configuring the User in OMC
To create a generic SIP set:
1. In OMC, go to Users/Base stations List.
2. Select a No., IP access and click on the Add button.
3. Select IP terminal and enter a Name.
4. Select the newly created user in the list and select Basic SIP Phone or Open SIP Phone
in the combo box.
See the different features relating to basic or open SIP modes: section Services offered
on SIP and DECT (IP-DECT) sets in document [3].
5. Click the Modify button.
6. Click the Details button. The User window is opened.
7. Click the IP/SIP button. The IP/SIP parameters window is opened.
8. In the SIP parameters tab, click the SIP password reset button. A new password is
generated in the SIP password field.
9. A virtual MAC Address is automatically generated but it can be replaced by the real MAC
Address of the SIP device.

 !"#!$% & '#! & ( ) "#!* &             105/160
  
Chapter 4    % 

Note:
The MAC Address must be unique and is used to identify the subscriber in the OXO Connect call
handling (SIP password is used for authentication).
10. Note this new password safely. It will be requested during the generic SIP set configuration
( Configuring the generic SIP set ).
4.6.1.2.3 Connecting the Set
This section describes how to:
- Connect a generic SIP set to the LAN (Local Area Network)
- Connect the power supply
Prerequisites
None
Connecting a SIP set to the LAN

Note:
If the set is supplied via Ethernet, ensure you are using a 802.3af standard-compatible switch.
To connect the set to the LAN:
- Plug the RJ45 cable into the set's LAN connector.
- Connect the RJ45 cable to the LAN.
Connecting Power Supply (Optional)
To supply power via an AC/DC external adapter:
- Plug the appropriate cable from the adapter into the set's power supply connector.
- Connect the plug from the adapter to the mains power supply.
4.6.1.2.4 Configuring the generic SIP set
The following parameters must be entered through the MMI or web interface when available:
- IP address (if no DHCP server is configured)
- Subnet mask (if no DHCP server is configured)
- Gateway adress (if no DHCP server is configured)
- DNS adresses (if no DHCP server is configured)
- VLAN use (if no DHCP server is configured)
- VLAN ID if VLAN use is set (if no DHCP server is configured)
- SIP username
- SIP password: this is different from the user password. It is randomly generated for each
SIP phone by the system and must be provided to the user in a secured way. It is used
both for SIP registration and for SIP authentication, since every SIP message must be
authenticated.

106/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

Note:
The random password must be entered manually in MMI. It must be made of with letters and
numbers only and can be viewed/reset in OMC.
This password has been previously generated in: Configuring the User in OMC .
- SIP Phone Signal Source Port: default value is 5059. This value can be modified to any
valid free port.
- Registrar and proxy IP addresses: the OXO Connect IP address and the SIP port must
be set to value 5059
- Authentication Realm: OXO Connect IP address by default
- Registration interval: value greater than 120 seconds
- Transport protocol: the UDP protocol is preferred, TCP is used if the SIP packet length is
greater than the MTU value or if the remote SIP endpoint requests the TCP protocol
- Domain name: OXO Connect IP address by default
4.6.1.2.5 Configuring OXO Connect DHCP server
Generic SIP phones can use the OXO Connect DHCP server.
By default the OXO Connect DHCP server is not activated for generic SIP phones.
To activate the OXO Connect DHCP server:
1. In OMC, go to Hardware and Limits > LAN/IP Configuration > DNS/DHCP
2. In the Advanced DHCP IP range area, select the Enable check box.
3. Define the range of IP addresses ( Start IP address and End IP Address).
4. Click the OK button to confirm your entries.
For DHCP advanced configuration, refer to the section DHCP configuration in document [14].
4.6.1.2.6 Displaying SIP Connection Current Status
This feature allows the display of SIP connection status.
To display SIP connection status:
1. In OMC, go to Users/Base stations List > Details.
2. Read the SIP connection status (under the terminal's physical status).
The following table lists the different displayed status.
Displayed Status Meaning
Set not connected SIP phone disconnected from network / No
SIP registration request from the phone
SIP registration KO SIP registration request from SIP Phone rejec-
ted by OXO Connect
Set unregistered SIP phone unregistered from OXO Connect
SIP registration OK SIP phone connected and successfully re-
gistered to OXO Connect

4.7 4018 Phone Extended Edition

 !"#!$% & '#! & ( ) "#!* &             107/160
  
Chapter 4    % 

4.7.1 Basic description

4.7.1.1 Overview
As part of the Proprietary professional range, IP phones are fully-featured with integrated IP
connectivity and telephony, bringing you the converged power of data and voice over IP
(VoIP). In addition to their optimized design, these terminals offer a gray display, wide band
audio, superior quality ring tones and hands-free communication.
The sets offer the following advantages:
- Instant Business Communications
- Optimized Ergonomics
- Superlative sound quality
- Unbeatable range of telephony features
4.7.1.2 Instant Business Communications
The Alcatel-Lucent IP Touch 4018 phone Extended Edition sets are always ready to provide
the best communication service whenever you need it, and to connect to other devices and
applications in real-time. You'll find them fast and easy to use, with feature buttons and
interactive soft keys.
4.7.1.3 Optimized Ergonomics
Attractive, innovative and intuitively designed, these terminals operate on the same simple,
user-friendly ergonomics found in the best mobile phones and PDAs, so that you won't waste
any time accessing their powerful features and services. These phones come complete with:
- Display in different shades of gray
- Programmable feature buttons
- Up/down navigator
- Context-sensitive keys
4.7.1.4 Superlative sound quality
These phones provide the very best sound quality thanks to the following new enhancements:
- Compatibility with wide band audio, taking listening comfort to higher levels
- Full duplex hands-free speakerphone, including acoustic echo cancellation
- A comprehensive choice of standard ringtones and polyphonic melodies
4.7.1.5 Unbeatable range of telephony features
These sets offer the full range of telephony services found in the OXO Connect PBXs,
unbeatable in terms of functionality, features, reliability and Quality of Service. These sets are
available in all countries where the associated IP-enabled OXO Connect system releases are
launched.

4.7.2 Hardware description

108/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

4.7.2.1 Alcatel-Lucent IP Touch 4018 phone Extended Edition set description

This section describes the:
- Set features
- Set keyboard
- Set display
The following figure illustrates the Alcatel-Lucent IP Touch 4018 phone Extended Edition set.

Figure 4.32: Alcatel-Lucent IP Touch 4018 phone Extended Edition set

4.7.2.1.1 Set features

The features of the Alcatel-Lucent IP Touch 4018 phone Extended Edition set are as follows:
- Corded comfort handset
- Full duplex hands-free
- Wide band audio
- Standard ring tones and polyphonic melodies
- Display in shades of gray
- Dialing keypad
- Fixed function keys

 !"#!$% & '#! & ( ) "#!* &             109/160
  
Chapter 4    % 

- Up/down navigator and OK key

- Programmable keys
- Ethernet LAN and PC connections
- Optical connectivity with external adapter
- Wall mounted kit [optional]
- Foot-stand 60° (“Big Foot”) [optional]
4.7.2.1.2 Set keyboard
The keyboard of the Alcatel-Lucent IP Touch 4018 phone Extended Edition set includes:
- A dialing keypad
- Function keys
- Programmable keys
- A navigator
Dialing keypad
The dialing keypad comprises 12 keys.
Function keys
The fixed function keys are described in the table below.
table 4.16: Fixed keys
Key Action
End Can be used to:
- terminate the current communication
- stop ringing for an incoming call
- end the current application (and return
the display to its default)
Hands–free (with green LED) Enables or disables the hands–free feature.
Short press activates the hands-free feature.
Long press on the hands-free key activates
the Group Listening feature.
The hands-free function is a full duplex func-
tion with echo cancellation and attenuation.
Volume In OXO Connect, they adjust:
+ - the handset/headset volume in commu-
— nication mode
- the built-in loudspeaker volume
- the ringing level when the set rings
Redial - Short press: Automatically redials the
last number dialled.
- Long press: Displays a list of recently di-
alled numbers. Use the up/down arrow
keys to scroll between numbers, and
press the OK key to redial the number
currently displayed.

110/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

Key Action
Message (with orange LED) Provides access to:
- voice-mail services
- mini-message services
Mute (with green LED) - When the set is in communication, this
key switches the set to mute mode
(disabling the set's microphone).
- When the set is not in communication,
this key allows an incoming internal call
to be answered in hands-free mode.
Personal/Dial by name - Short press: Provides access to the per-
sonal address book.
- Long press: Provides access to the Dial
by name feature.
Exit/Home - Short press: Steps back one level in the
application.
- Long press: Exits the current application
and returns to the default display.
Help/Menu Menu
- Press once to access the set's menu.
This consists of 7 elements - use the up/
down arrow keys to move between menu
elements.
- Press once followed by one of the keys 1
to 7 to access the corresponding element
of the menu.
- Press once followed by the OK key to ac-
cess the first element of the menu (Who
Am I?).
Help
Press once followed by another key to obtain
information on the function of that key. The
possibilities are:
- i + programmable key
- i + Message key
- i + Redial key
- i + End key
- i + Personal/Dial by name key

Programmable keys
The programmable keys allow your preferred functions to be programmed (by an
administrator), such as call forwarding or a specific call number. These keys then provide
quick and easy access to these functions.
The programmable keys include:
- One personal key
- A set of 6 other programmable keys
Navigator
The navigator includes:

 !"#!$% & '#! & ( ) "#!* &             111/160
  
Chapter 4    % 

- A 2-direction navigation key

- A validation key (OK)
- An Exit/Home key (|<)
The Exit/Home key is used to exit the current application, or a long press will switch the display
back to its default. In edit mode, it can be used to delete characters.
4.7.2.1.3 Set display
The table below lists the characteristics of the display of the Alcatel-Lucent IP Touch 4018
phone Extended Edition set.
table 4.17: Display of the Alcatel-Lucent IP Touch 4018 phone Extended Edition set
Characteristics Alcatel-Lucent IP Touch 4018 phone Extended
Edition
Display Yes
Screen resolution 20 characters
Size of visible area 79 x 13 mm (3.11 x 0.51 inches)
Color Gray background

4.7.3 Commissioning
4.7.3.1 Overview
This module presents all the actions required for commissioning the Alcatel-Lucent IP Touch
4018 phone Extended Edition set.
The following figure illustrates the connectors on the base of the Alcatel-Lucent IP Touch 4018
phone Extended Edition sets.

112/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

Figure 4.33: Alcatel-Lucent IP Touch 4018 phone Extended Edition connectors

4.7.3.2 Commissioning the set

This section describes how to:
- Connect the set
- Initialize the set
- Program keys
4.7.3.2.1 Prerequisites
None.
4.7.3.2.2 Connecting the sets
This section describes how to:
- Connect an IP Touch set to the LAN (Local Area Network)
- Connect the power supply
Prerequisites
None.
Connecting an IP Touch set to the LAN
To connect the set to the LAN:
1. Turn the set over so that you can see its base.

 !"#!$% & '#! & ( ) "#!* &             113/160
  
Chapter 4    % 

2. Plug the RJ45 cable into the set's LAN connector.

3. Connect the RJ45 cable to the LAN itself.
Connecting power supply
The set can be supplied from two possible power sources:
- An AC/DC external adapter which is a 42V power supply
A female jack is used to connect the power adapter. .
- Power over Ethernet (PoE)
The supply via Ethernet can be implemented using a 802.3af standard-compatible switch.
To supply power via an AC/DC external adapter:
1. Plug the appropriate cable from the adapter into the set's power supply connector.
2. Connect the plug from the adapter to the mains power supply.
Initialization starts.
4.7.3.2.3 Initializing the sets
This section describes how to:
- Choose the initialization mode
- Initialize the IP Touch set
Prerequisites
The IP Touch set must be connected to the:
- LAN
- Power supply
Choosing the initialization mode
The default mode is Dynamic Alcatel mode.
To choose the initialization mode, refer to the table below.
table 4.18: Initialization modes
If Then the required initializa- And
tion mode is
You use OXO Connect DHCP Dynamic or Proprietary Dy- - Refer to table: Initialization
server namic procedure
You use another DHCP server Dynamic mode Refer to table: Initialization
procedure

114/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

You do not use a DHCP serv- Static mode - Refer to table: Initialization
er procedure
- Obtain from your network
administrator:
• An IP address for the
IP Touch set
• The subnetwork mask
• The router address
• The TFTP server ad-
dress, which is the IP
address of the Power-
CPU EE board em-
bedding the VoIP
board

Initializing the IP Touch set

To initialize the IP Touch set, refer to the table below.
Note 1:
In each of the three cases below, you can view the IP Touch set's software version after Step 2 by
selecting Version in the Main menu.
table 4.19: Initialization procedure
For an initializa- Procedure
tion that is
Dynamic Alcatel 1. If necessary, enable the OXO Connect DHCP server (in OMC, Hardware and
Limits > LAN/IP Configuration > DNS/DHCP)
2. Connect the power supply.
3. After initialization phase 2 is completed and before phase 5 starts, press i, then
the # key.
The Main menu appears.
4. If the set was previously in static mode, select IP Parameters from the Main
menu.
The IP Parameters menu appears.
5. Select Dynamic and press the OK key.
6. Save by pressing the # key.
7. Exit the Main menu by pressing the * key.
Dynamic mode 1. Connect the power supply.
2. After initialization phase 2 is completed and before phase 5 starts, press i, then
the # key.
The Main menu appears.
3. If the set was previously in static mode, choose IP Parameters from the Main
menu.
The IP Parameters menu appears.
4. Choose Dynamic and press the OK key.
5. Save by pressing the # key.
6. Exit the Main menu by pressing the * key.

 !"#!$% & '#! & ( ) "#!* &             115/160
  
Chapter 4    % 

Static 1. Connect the power supply.

2. Before initialization phase 5 starts, press i, then the # key.
The Main menu appears.
3. From the Main menu, choose IP Parameters.
The IP Parameters menu appears.
4. Choose Static and press the OK key.
5. Enter the following:
a. IP address
b. Subnetwork mask
c. Router address
d. TFTP server address
e. TFTP port (69)
f. CPU address
6. Enter the required VLAN details, as follows:
a. If required, select Use VLAN and then enter the VLAN ID number.
b. Ensure that Strict VLAN is set as required. It is selected by default; de-
selecting it allows you to use a DHCP server in another VLAN.
7. Save the above parameter values by pressing the # key.
8. Exit the Main menu by pressing the * key.
The set restarts from phase 1 with the new parameters.
Note 2:
If an error message appears during initialization, disconnect the power adapter, then plug it in
again, so that the system restarts initialization.

Restarting initialization
If you want to change a parameter value, restart initialization, as detailed below.
To restart initialization:
1. Disconnect the IP Touch set from the power supply.
2. Reconnect the power supply.
3. Execute the initialization procedure as detailed in table: Initialization procedure
4.7.3.2.4 Programming keys
This section describes how to program the programmable keys.
In fact, only the direct call key can be programmed (with a telephone number), which by
default is the sixth programmable key. However, the Personal/Dial by name key can be
programmed in a similar way.
To program a key:
1. Press the i key followed by the required programmable key.
2. Press one key of the 2-way navigator (up or down).
3. Enter the telephone number to be associated with this programmable key.
4. Press OK. The set then goes back to its default display.
4.7.3.2.5 Relocating and retaining IP Touch sets
This section describes how to relocate and retain the same set.

116/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

In the procedure below, it is assumed that:

- there is one DHCP server
- no VLAN has to be configured.
Prerequisites
None.
Relocating and retaining the same set
To relocate and retain the same set:
1. Unplug the set.
2. Plug the set into a connector at its new location.
4.7.3.3 Rebooting the set
To reboot a set:
1. In OMC, go to Users/Base stations List > Details.
2. Click Reset button.
The Reset window opens.
3. Select Reboot and click OK.
4. In the confirmation window, click Yes.

4.7.4 Maintenance
4.7.4.1 Overview
This module describes:
- The error and information messages that appear during the starting phase.
- The Ethernet link table.
4.7.4.2 Error and Information messages
The table below lists the error and information messages. It has the following format:
Short text = text displayed on the screen, in case of real error or for information.
Description = status/error description
table 4.20: Starting phase error messages
Short text Description
END Starting phase is terminated (successful or
unsuccessful)
STARTED Step started
SUCCESS Step successful
FAIL Step failed
RETRYING Retrying step

 !"#!$% & '#! & ( ) "#!* &             117/160
  
Chapter 4    % 

Short text Description

NO MAC ADDRESS No Ethernet MAC address stored in flash
DHCP NOT RESPONDING DHCP Server is not responding
BAD IP ADDRESS IP address is incorrect
BAD ROUTER ADDRESS Router address is incorrect
ROUTER PING FAILED Router not responding to ping
BAD TFTP ADDRESS TFTP server address is incorrect
ADDRESSES MISMATCH Address, mask and router do not match
TFTP NOT RESPONDING TFTP server is not responding
TFTP SERVER ERROR TFTP server error
BAD FILE CONTENT Error found in downloaded file
FILE TOO LARGE File is too large (cannot be downloaded)
SAME VERSION FOUND The version retrieved is the same as the ver-
sion running
NEW VERSION FOUND New IP Touch software version found
(download)
FLASHING Flashing in progress
FLASHING FAILED Failed to flash downloaded binary
TRYING ANOTHER CPU Trying next address from configuration file
NO ETHERNET LINK Ethernet link not connected (LAN port only)
initializing First text message after hardware reset and
copyright information
1/5 network start Phase 1 is running: the set is starting its net-
work interface
2/5 network setup Phase 2 is running: the set is looking for IP
addresses
3/5 config download Phase 3 is running: the set is trying to get a
lanpbx file
4/5 binary download Phase 4 is running: the set is downloading a
new binary
5/5 connecting Phase 5 is running: the set is trying to talk to
the system

4.7.4.3 Ethernet Link

By default, Alcatel-Lucent 8 series sets are configured to perform auto-negotiation on both
ports (LAN and PC). Provided that the PC and the LAN switch are also configured to perform
auto-negotiation, this is the best configuration for QoS improvement.
However, depending on the network configuration, it may not always be possible to leave the
terminal in auto-negotiation: link speed and duplex of both ports can be forced to determined
values using the supervisor menu:
- Plug in the set, as described: IP Touch 4018 Phone - Commissioning - Commissioning the
set .

118/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

- Once the set displays initialization, press i, then #.

- Use the navigation key to select Ethernet Links
- Modify data as requested
A configuration mismatch between the terminal and PC/LAN switch can lead to negative
effects on the voice quality:
- No link (or speed mismatch): 8, 9, 11 and 12
- Packet loss (or duplex mismatch): 2, 4, 7 and 14
Note 1:
Collisions are not detected by the device operating in full-duplex mode: packets from this device are
never re-transmitted if a collision occurs on them.
The following table lists all possible Ethernet port configuration combinations when connecting
an IP Touch set to an external device (switch on LAN side, PC on PC side). For each
combination, the table shows the link status: valid or invalid (duplex or speed mismatch), as
described above.
table 4.21: Ethernet Link Combinations
Terminal Port External Device Port Link Status
1 auto-negotiation auto-negotiation Valid
2 auto-negotiation 100-FULL Invalid (packet loss)
3 auto-negotiation 100-HALF Valid
4 auto-negotiation 10-FULL Invalid (packet loss)
5 auto-negotiation 10-HALF Valid
6 100-FULL 100-FULL Valid
7 100-FULL 100-HALF Invalid (packet loss)
8 100-FULL 10-FULL Invalid (no link)
9 100-FULL 10-HALF Invalid (no link)
10 100-HALF 100-HALF Valid
11 100-HALF 10-FULL Invalid (no link)
12 100-HALF 10-HALF Invalid (no link)
13 10-FULL 10-FULL Valid
14 10-FULL 10-HALF Invalid (packet loss)
15 10-HALF 10-HALF Valid

Note 2:
When the two ports of an Alcatel-Lucent IP Touch 4018 Phone or Alcatel-Lucent IP Touch 4018 phone
Extended Edition set are configured in auto-negotiation mode, if the negotiation has led to a 10 Mbps rate
on the PC port and a 100 Mbps rate on the LAN port, the Alcatel-Lucent 8 series set automatically tries to
renegotiate a 10 Mbps rate on the LAN port. This prevents congestion problems on the PC.

4.8 8029/8039 Premium Deskphones

 !"#!$% & '#! & ( ) "#!* &             119/160
  
Chapter 4    % 

4.8.1 Detailed description

4.8.1.1 Basic description
The available Digital Premium DeskPhones are:
- 8039 Premium DeskPhone
- 8029 Premium DeskPhone
4.8.1.2 Environmental requirements
- Storage temperature: -25°C to 55°C (ETSI EN 300 019-1-1 Class 1.2)
- Transportation temperature: -40°C to 70°C (ETSI EN 300 019-1-2 Class 2.3)
- Temperature controlled enclosed location: -5°C to 45°C (ETSI EN 300 019-1-3 Class 3.2)
- Relative humidity: 5% to 95% (ETSI EN 300 019-1-3 Class 3.2)
4.8.1.3 Hardware description
4.8.1.3.1 Phone layouts
Although there are differences in the aspect and operation of these sets, their layout is
identical, but for the screen and number of available soft keys.

120/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

Figure 4.34: 8039 Premium DeskPhone set layout

 !"#!$% & '#! & ( ) "#!* &             121/160
  
Chapter 4    % 

Figure 4.35: 8029 Premium DeskPhone set layout

4.8.1.3.2 Embedded hardware

An IVANOE2 Chip with ARM7TDMI RISC processor is included in 80x9 sets, associated with
external SRAM (256Kx16) and NOR Flash (512Kx16) memories.
4.8.1.3.3 Foot stand
All sets come with a 0° to 60° adjustable foot stand.
4.8.1.3.4 Audio, handsets, hands free and headset
All sets come with a standard 3.5mm jack to plug a headset. They offer narrowband audio
qualities.
All sets come in their standard version with a comfortable corded handset.
They all work in hands free mode at the user's request.
4.8.1.3.5 Screens
Characteristics of set displays are:
- 8039 Premium DeskPhone: black and white graphical display of 160 by 100 dots, with
white backlight
- 8029 Premium DeskPhone: black and white graphical display of 64 by 128 pixels with
white backlight

122/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

4.8.1.3.6 Keys
Dialing keypad
All sets come with a standard 12-key dialing keypad.
Fixed keys
On all sets:
- Two fixed keys below the keypad:
• : the Start call key puts the set in hands free mode

• : the Stop call key allows to end a call and ignore an incoming call

- A four-direction set of navigation keys (left, right, up, down) allows to select the different
options available on the screen. The OK button in the center of the navigation validates the
selection.
- The c key to the left of the navigation allows to cancel the current action.
- Sensitive (piano) keys are located above the black grid of the lower part of the set.
Starting from the left to the right, they provide access to the following features:
• mute sound

• decrease sound volume

• increase sound volume

• put loudspeaker in service

• hold call. This is the default feature for F1 keys (but can be programmed with
another feature)
• transfer call. This is the default feature for F2 keys (but can be programmed with
another feature)
redial information

• information page (displayed on screen)

• messaging services

Integrated additional programmable keys

On 8029 Premium DeskPhone sets, four add-on keys, each with a LED, allow to customize
each set according to the user's needs. A paper label at the right of these keys allows to write
down a brief description of the feature programmed on the key.
4.8.1.4 Connecting optional equipment
4.8.1.4.1 Alphabetic keyboard
A standard (hot pluggable) optional keyboard is available for all sets in the following layouts:
- Azerty (FR)

 !"#!$% & '#! & ( ) "#!* &             123/160
  
Chapter 4    % 

- Qwertz (DE)
- Qwerty (international)
- Qwerty (Nordic)
If you change keyboard types, ensure it is plugged in before restarting the set.
4.8.1.4.2 External interfaces
On all sets, a 3.5mm jack connector allows to plug a headset to the phone.

Figure 4.36: External interfaces on the back of 80x9 sets

4.8.1.4.3 Additional key modules

On all sets, several add-on modules, connected via SATA (see: External interfaces ), can
complete the standard number of programmed keys.
The available modules are:
- 10-key module (can be fastened to the set):

- 40-key module (on its own foot stand, placed next to the set)

124/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

- Smart-key module (on its own foot stand, placed next to the set)

4.8.2 Commissioning
4.8.2.1 Connecting the set
4.8.2.1.1 Physical connection
To connect the set to the OXO Connect:
1. Plug the RJ11 cable in the corresponding set connector on the back of the set
2. Plug the other end of the cable onto the UA board on which the set has been declared
The set starts initializing automatically.
If this is the first set initialization, or when there has been an upgrade of the PBX software
version, the set downloads binary and data files.
4.8.2.1.2 Connecting an Add-On module to the sets
Add-On Modules (AOMs) can be connected to sets. They are added to the right side of the
set.
Three types of Add-On Module exist and provide keys associated with icons:

 !"#!$% & '#! & ( ) "#!* &             125/160
  
Chapter 4    % 

- AOM10 provides 10 keys

- AOM40 provides 40 keys
- Smart Display Module provides 14 keys with programmable LCD labels
Rules and restrictions
The following rules apply to the use of Add-On Modules:
- A maximum of three Add-On Modules of the types AOM10 and AOM40 can be connected
to each set, providing up to 120 additional keys.
- A maximum of three Smart Display Modules can be connected to each set, providing up to
42 additional keys.
- Add-On Modules of types AOM10 and AOM40 can be used on the same set, but a Smart
Display Module cannot be used in conjunction with an AOM10 or AOM40.
- If an AOM10 is used with other Add-On Modules, it must be connected as the last module
on the far right of the set.
Connecting Add-On Modules
To connect an Add-On Module:
1. Remove the tab located on the right side of the set.
2. Plug the Add-On Module's SATA connector into the set's SATA connector.
3. Insert the Add-On Module attachments into the appropriate holes located on the right side
of the set. (AOM10 only)
4. Screw the Add-On Module to the set. (AOM10 only)
Note:
If the set is on when you plug in an Add-On Module, you must restart the set after connection.

4.8.2.1.3 Binary file download

To operate correctly, Digital Premium DeskPhones sets require binary files which must comply
with the PBX version and configuration. After system upgrade and each time a set initializes,
version numbers of binary files are verified to determine whether an update of these files is
necessary.
When a file is downloaded to set, it overwrites any previously existing file.
Application download to a terminal can be heavy in terms of bandwidth and CPU resources. It
is not possible to upgrade all the terminals during initialization of the system.

4.9 4019 Digital Phone

4.9.1 Basic description

4.9.1.1 Overview
This phone is part of the ALE International professional range. In addition to its optimized
design, this terminal offers a gray display, wide band audio, a choice of ring tones, and group
listening.

126/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

The Alcatel-Lucent 4019 Digital Phone set offers the following advantages:
- Instant Business Communications
- Optimized Ergonomics
- Superlative sound quality
- Wide range of telephony features
4.9.1.2 Instant Business Communications
The Alcatel-Lucent 4019 Digital Phone is always ready to provide the best communication
service whenever you need it, and to connect to other devices and applications in real-time.
You'll find it fast and easy to use, with feature buttons and interactive soft keys.
4.9.1.3 Optimized Ergonomics
Attractive, innovative and intuitively designed, this terminal operates on the same simple,
user-friendly ergonomics found in the best mobile phones and PDAs, so that you won't waste
any time accessing its features and services. The phone comes complete with:
- Gray display
- Programmable feature buttons
- Up/down navigator
- Context-sensitive keys
4.9.1.4 Superlative sound quality
This phone provides the very best sound quality thanks to the following new enhancements:
- A group listening capability from its built-in speaker
- A comprehensive choice of standard ringtones and polyphonic melodies
4.9.1.5 Unbeatable range of telephony features
This set offers the full range of telephony services found in the OXO Connect PBXs from ALE
International, unbeatable in terms of functionality, features, reliability and Quality of Service.
The set is available in all countries where the associated OXO Connect system releases are
launched. It is compatible with OXO Connect release 4.0.

4.9.2 Hardware description

4.9.2.1 Alcatel-Lucent 4019 Digital Phone set description
This section describes the:
- Set features
- Set keyboard
- Set display
The following figure illustrates the Alcatel-Lucent 4019 Digital Phone set.

 !"#!$% & '#! & ( ) "#!* &             127/160
  
Chapter 4    % 

Figure 4.40: Alcatel-Lucent 4019 Digital Phone set

4.9.2.1.1 Set features

The features of the Alcatel-Lucent 4019 Digital Phone set are as follows.
- Corded comfort handset
- Group listening through built-in loudspeaker
- Standard ring tones and polyphonic melodies
- Gray display
- Dialing keypad
- Fixed function keys
- Up/down navigator and OK key
- Programmable keys
- Wall mounted kit [optional]
- Foot-stand 60° (“Big Foot”) [optional]
4.9.2.1.2 Set keyboard
The keyboard of the Alcatel-Lucent 4019 Digital Phone set includes:
- A dialing keypad

128/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

- Function keys
- Programmable keys
- A navigator
Dialing keypad
The dialing keypad comprises 12 keys.
Function keys
The fixed function keys are described in the table below.
table 4.22: Fixed keys of the Alcatel-Lucent 4019 Digital Phone set
Key Action
End Can be used to:
- terminate the current communication
- stop ringing for an incoming call
- end the current application (and return
the display to its default)
Loudspeaker (with green LED) Enables or disables the built-in loudspeaker.
This key activates the group listening feature.
Volume In OXO Connect, they adjust:
- + - the handset/headset volume in commu-
- — nication mode
- the built-in loudspeaker volume
- the ringing level when the set rings
Redial - Short press: Automatically redials the
last number dialled.
- Long press: Displays a list of recently di-
alled numbers. Use the up/down arrow
keys to scroll between numbers, and
press the OK key to redial the number
currently displayed.
Message (with orange LED) Provides access to:
- voice-mail services
- mini-message services
Mute (with green LED) When the set is in communication, this key
switches the set to mute mode (disabling the
set's microphone).
Personal/Dial by name - Short press: Provides access to the per-
sonal address book.
- Long press: Provides access to the Dial
by name feature.
Exit/Home - Short press: Steps back one level in the
application.
- Long press: Exits the current application
and returns to the default display.

 !"#!$% & '#! & ( ) "#!* &             129/160
  
Chapter 4    % 

Key Action
Help/Menu Menu
- Press once to access the set's menu.
This consists of 7 elements - use the up/
down arrow keys to move between menu
elements.
- Press once followed by one of the keys 1
to 7 to access the corresponding element
of the menu.
- Press once followed by the OK key to ac-
cess the first element of the menu (Who
Am I?).
Help
Press once followed by another key to obtain
information on the function of that key. The
possibilities are:
- i + programmable key
- i + Message key
- i + Redial key
- i + End key
- i + Personal/Dial by name key

Programmable keys
The programmable keys allow your preferred functions to be programmed (by an
administrator), such as call forwarding or a specific call number. These keys then provide
quick and easy access to these functions.
The programmable keys include:
- One personal key
- A set of 6 other programmable keys
Navigator
The navigator includes:
- A 2-direction navigation key
- A validation key (OK)
- An Exit/Home key (|<)
The Exit/Home key is used to exit the current application, or a long press will switch the display
back to its default. In edit mode, it can be used to delete characters.
4.9.2.1.3 Set display
The table below lists the characteristics of the display of the Alcatel-Lucent 4019 Digital Phone
set.
table 4.23: Display of the Alcatel-Lucent 4019 Digital Phone set
Characteristics Alcatel-Lucent 4019 Digital Phone
Display Yes
Screen resolution 20 characters
Size of visible area 79 x 13 mm (3.11 x 0.51 inches)

130/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

Characteristics Alcatel-Lucent 4019 Digital Phone

Color Gray background

4.9.3 Commissioning
4.9.3.1 Overview
This module presents all the actions required for commissioning the Alcatel-Lucent 4019
Digital Phone set.
The following figure illustrates the connectors on the base of the set.

Figure 4.41: Alcatel-Lucent 4019 Digital Phone connectors

4.9.3.2 Commissioning the set

This section describes how to:
- Connect the set
- Program keys
4.9.3.2.1 Prerequisites
None.
4.9.3.2.2 Connecting the set
This section describes how to connect the set to the telephone system.
Prerequisites

 !"#!$% & '#! & ( ) "#!* &             131/160
  
Chapter 4    % 

None.
Connecting the set to the telephone system
To connect the set to the telephone system:
1. Turn the set over so that you can see its base.
2. Plug the RJ11 cable into the set's UA port/phone line connector.
3. Connect the RJ11 cable to a UA port in the telephone system.
4.9.3.2.3 Programming keys
This section describes how to program the programmable keys.
In fact, only the direct call key can be programmed (with a telephone number), which by
default is the sixth programmable key. However, the Personal/Dial by name key can be
programmed in a similar way.
To program a key:
1. Press the i key followed by the required programmable key.
2. Press one key of the 2-way navigator (up or down).
3. Enter the telephone number to be associated with this programmable key.
4. Press OK. The set then goes back to its default display.

4.10 Input Method Editor

4.10.1 Operation
The Input Method Editor (IME) allows a user to input non-Latin characters on sets with a
standard Latin keyboard (with or without special markings on the keyboard).
This input method is used for dial by name, customizing programmed key names and editing
text messages and configuring the phone names on the Operator set.
The IME supports Latin, Cyrillic, Hebrew and Chinese characters. For input of Chinese
characters, the IME opens an input session. The type of character is associated with an input
method:
Characters Input Method
Chinese - mainland China Pinyin, Latin
Chinese - Hong Kong Stroke, Latin
Chinese - Taiwan Zhuyin, Latin
Russian Cyrillic, Latin
Hebrew Hebrew, Latin

Note 1:
For the input methods of Pinyin, Stroke and Zhuyin, when the target country is Chinese, or Cantonese, or
Taiwanese, these 3 input methods should be used. If not, these 3 input methods are not used.
For the input method of Cyrillic, there are no restrictions. When the current language is Russian, it can be

132/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

used.
Opening an IME input session:
When one of the Chinese input methods is used, an input session starts when the user
presses an alpha key.
The following figure shows the schema of the IME input session. It appears on the bottom
softkey line of the set's screen display.

Figure 4.42: Open the IME input session

The softkeys and areas operate in IME as follows:
- The input area displays characters as the user enters them.
Note 2:
For Pinyin input method, Latin characters are displayed in the input area.
- The result area displays the list of candidate characters in the same character type as the
input method.
- The input method indicator shows the input method in use.
- The left softkey is used to toggle between input methods.
- The right softkey is not used.
The following screens show an example of the basic operation of an IME input session. In the
example the input method is Pinyin.
The following figure shows the IME after the user has entered the letters "yu".

 !"#!$% & '#! & ( ) "#!* &             133/160
  
Chapter 4    % 

Figure 4.43: Opened IME session with entered letters

The letters “yu” is displayed in Latin character type in the input area of the IME. The input
method indicator shows the current input method is Pinyin. The result area lists candidate
Chinese characters for the input letters “yu”.
The way input characters are processed, the resulting candidate characters displayed, and the
function of special keys varies according to input method.
Closing an IME input session:
The IME input session closes automatically when no activity is detected from the user. Two
timers control this function. When the first timer, T1, expires, it closes the input session without
clearing the input and result areas. The second timer, T2, should be greater than T1. When T2
expires, it closes the input session and clears the input and result areas. Both timers are
reloaded every time the user presses an alpha key. If the user presses an alpha key after T1
has expired, but T2 has not yet expired, the input session is re-opened with the previous
contents of the input and result areas.
The input session also closes when the user presses:
- OK (confirms character choice)
- RELEASE
- Back/Exit
Changing input methods:
The user can change the current input method to any which is configured on the set by
pressing + ([alt] + [space]). An input method selector dialog box pops up,
displaying the possible input methods, as shown in the following figure.

134/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

Figure 4.44: Change input method

In the pop-up dialog box, the user scrolls with [space] (while keeping [alt] pressed), and selects
by releasing [alt]. If the Latin or Cyrillic input method is selected, the IME input session closes
because it is not used by these input methods.
Note 3:
If the language is Russian, there are no input sessions for Cyrillic, after changing the input method to
Cyrillic, it can input Russian character directly on the alphabetic keyboard.
Alternately, when the current Input Method is Pinyin, the user can use the left softkey to toggle
between two input methods. In this example, if the user presses the left softkey, the current
input method toggles from Pinyin to Latin and the IME input session remains open, as shown
in the following figure.

Figure 4.45: Toggle input method; example screen 1

Now the user can input Latin characters directly without closing the input session. The input
method indicator shows that the current input method is Latin. After one Latin character is
entered ("U"), the input session closes, although Pinyin is still available as the default input
method.
To toggle back to Pinyin, the user presses the left softkey and the input session re-opens, as
shown in the following figure.

 !"#!$% & '#! & ( ) "#!* &             135/160
  
Chapter 4    % 

Figure 4.46: Toggle input method; example screen 2

Input Method for programming a key name:
Each user can program the key name on the phone. In this case, the input session does not,
however, close automatically after the user presses OK to confirm a Unicode character. It is
kept until the user presses the Back/Exit key, followed by OK to save the key name.

Figure 4.47: Program a key name

Input Method for programming names on the Operator set:
Note 4:
It is possible to use Unicode - Chinese, Hebrew and Cyrillic -characters.
The administrator of OXO Connect can modify all the phone names via the operator set. This
case is the same as the one presented above - "Programming a key name". The input session
will not close automatically after pressed OK to confirm a Unicode character. It is kept until the
user presses the Back/Exit key followed by OK to save the phone name.

136/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

Figure 4.48: Configure a phone name

4.11 Terminal downloading

4.11.1 Operation
4.11.1.1 Overview
The Digital Premium DeskPhones telephone sets contain software and data files that are
pre-installed in the factory
Data files include components such as fonts and ring tones, which may be country specific.
OXO Connect provides the facility for the software and/or data files embedded in the terminals
to be updated by the call server if the versions of the embedded files are different from the
versions of the equivalent files available in the OXO Connect system. In this case, the relevant
files are normally downloaded from the system to the terminal when the terminal is restarted.
Note:
New terminal software versions may become available in the system when the system is updated with
new OXO Connect software. Updates of the files embedded in the terminals may then be required.

4.11.1.2 Timing
The terminal download mechanism is activated when a terminal is restarted. During the restart
phase, the versions of the files embedded in the terminal are compared with the versions of
the same files available for download from the system. If the two versions of the same file are
different, a download request is sent to the call server. When the call server detects a
download request from a terminal, the terminal is entered into a queue of terminals waiting for
downloads.
Note:
A terminal may also request a download during the restart phase if the files inside the terminal have been
corrupted, or if the previous download failed or was interrupted.
The user can delay a terminal download so that it is performed at a specified time (date and
hour). This allows terminal downloading to be performed at a convenient time, such as during

 !"#!$% & '#! & ( ) "#!* &             137/160
  
Chapter 4    % 

business closing hours or at weekends.

Other deviations from the normal download procedure are also possible:
- The user can specify that the next terminal download will be performed following the next
software swap (when the system switches to running the new software).
- The user can force a download, even if the versions of the embedded files are the same as
the versions of the equivalent files in the system.
- The user can choose to forbid downloads, even if the versions of the embedded files are
different from the versions of the equivalent files in the system.
The timing of terminal updates is configured in the OMC tool, which presents the following
options:
- No Downloading: There will be no updates to the files embedded in the terminals.
- Download after swap: New files will be downloaded to the terminals following the next
software swap.
- Delay Downloading at: New files will be downloaded to the terminals at the specified date
and time.
- Download immediately: New files will be downloaded to the terminals immediately (a
forced download).
4.11.1.3 Operation
During a terminal download, the following conditions apply:
- The terminal cannot be used (the call server puts the terminal out of service).
- The terminal must not be re-configured (with the configuration tools).
- If a problem occurs during a download, the download is attempted a second time. If the
problem persists, the terminal is put out of service.
- If a terminal download is not performed within a certain timeout period from the time of the
download request, the terminal is reset. See the note below.
- If two terminals share the same telephone resources, they cannot be updated
simultaneously - the downloads to the two terminals are performed sequentially.
Note:
If a timeout occurs during a download, you are advised to disconnect and then reconnect the terminal to
the system, so that the download procedure restarts.

4.11.1.4 Duration
The time taken to complete a terminal download depends on the number of terminals that are
being updated at the same time, as well as how and where the terminal is connected to the
system, as follows:
- The more terminals there are to be updated, the longer the expected wait for an individual
terminal to be updated.
- Downloads to terminals connected to extension cabinets take longer than to terminals
connected to the main cabinet.
- Downloads to terminals with shared system connections take longer than to terminals with
dedicated system connections.

138/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

4.12 Add-on Module

4.12.1 LEDs and icons on AOM modules

4.12.1.1 Overview
Extension units, also called Add-on Modules (AOM), can be fitted to the phone sets. They
provide additional keys which can be configured as call keys, feature keys, and resource keys.
Some keys have their status indicated by icons or LEDs. For example, a blinking icon indicates
that a user action is required.
For feature keys, an active feature is indicated by a LED ON and if a user action is requested
(for example, message not read), the LED blinks slowly.
For resource keys, icons and LEDs provide information such as:
- indicates that the contact hears music (hold state)

- indicates that the communication concerns the user

- indicates an incoming call

- LED ON (fixed) indicates a busy state not activated by the user

- Slow blinking LED indicates a resource used by the user
- Fast blinking LED indicates that a user action is requested (incoming call or call hold)
4.12.1.2 LEDs and icons description
The table below displays the different icon and LED states that can be applied to the feature
and resource keys:
Logical states LED states Icon states
Feature keys:
Inactive feature OFF OFF
Active feature ON
Priority feature SLOW BLINKING
Resource keys:
Free OFF OFF
Own call FAST BLINKING

In use SLOW BLINKING

Exclusive hold FAST BLINKING

Exclusive hold forgotten FAST BLINKING

 !"#!$% & '#! & ( ) "#!* &             139/160
  
Chapter 4    % 

Logical states LED states Icon states

Own recall (supervised call) FAST BLINKING

In call FAST BLINKING

Busy ON
Common hold FAST BLINKING

Common hold forgotten FAST BLINKING

4.13 V24/CTI Interface Module

4.13.1 Hardware description

4.13.1.1 Overview
The V24/CTI Interface Module allows a Data Terminal Equipment (DTE) to be connected to
the OXO Connect, via a UA link, by means of an RS232 serial link (CTI port) or a V24 link.
The V24/CTI Interface Module can be used alone or combined with Digital Premium
DeskPhones.
CTI port
The RS232 serial link carries signalling (up to 9600 bit/s) and allows telephone operations
such as call management and call monitoring. The audio part is carried out by the associated
dedicated set.
V24 port
The V24 port is considered as a DCE and provides a capacity of 19200 bit/s (ECMA 102) for
an asynchronous V24 transmission. The electrical interface complies with the V28
recommendation of the CCITT.

140/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

Figure 4.49: V24/CTI Interface Module Configuration Example

4.13.1.2 Compliant Standards

4.13.1.2.1 Safety Requirements
- EN60950: European requirements
- UL 1950: US requirements
- CAN/CSA-C22.2 No 950-95: Canada
4.13.1.2.2 ECM
- EN55022: Limits and methods of measurement of radio interference characteristics of
information technology equipment
- EN55024: Limits and methods of measurement of immunity characteristics of information
technology equipment
- FCC part15: US requirements
4.13.1.2.3 V24 & CTI
- CCITT Rec.: V24,V28, V25bis, V54, V110
- Hayes protocols
- ECMA 102: Attachment requirements for pan-European approval for connection to PSTN
of TE (excluding TE supporting the voice telephony service) in which network addressing,
if provided, is by means of DTMF signalling
4.13.1.2.4 Environment Classes
- ETS 300 019: Environmental conditions and tests for telecommunication equipment:
• Part 1-1: Storage
• Part 1-2: Transportation
• Part 1-3: Environmental conditions
4.13.1.2.5 Eco Design

 !"#!$% & '#! & ( ) "#!* &             141/160
  
Chapter 4    % 

- ISO 14040: Environmental management – Life cycle assessment – Principles and

framework (1997)
- RoHS

4.14 AP Interface Module

4.14.1 Hardware description

4.14.1.1 Overview
The AP Interface Module (Analog Peripheral) allows an analog device such as fax, modem,
minitel, answering machine to be connected to the OXO Connect via a UA link.
___change-begin___
___change-end___
Figure 4.50: Example of Configuration with an AP Interface Module
AP Interface Module can be used alone or combined with Digital Premium DeskPhones.
AP Interface Module powers the analog device (DTMF signalling, ringer) and, to do this,
requires an external power supply (230V AC/30V AC adapter). In this document, this set is
called Z set.
4.14.1.2 Compliant Standards
4.14.1.2.1 Safety Requirements
- EN60950: European requirements
- UL 1950: US requirements
- CAN/CSA-C22.2 No 950-95: Canada
4.14.1.2.2 ECM
- EN55022: Limits and methods of measurement of radio interference characteristics of

142/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

information technology equipment

- EN55024: Limits and methods of measurement of immunity characteristics of information
technology equipment
- FCC part15: US requirements
4.14.1.2.3 Analog Transmission
- ETS 300 439: Business TeleCommunications (BTC); Transmission characteristics of digital
Private Branch eXchanges (PBXs)
- TBR21: Attachment requirements for pan-European approval for connection to PSTN of
TE (excluding TE supporting the voice telephony service) in which network addressing, if
provided, is by means of DTMF signalling
4.14.1.2.4 Environment Classes
- ETS 300 019: Environmental conditions and tests for telecommunication equipment:
• Part 1-1: Storage
• Part 1-2: Transportation
• Part 1-3: Environmental conditions
4.14.1.2.5 Eco Design
ISO 14040: Environmental management – Life cycle assessment – Principles and framework
(1997)

4.15 S0 Interface Module

4.15.1 Hardware description

4.15.1.1 Overview
The S0 Interface Module allows an S0 bus (2 B + 1 D channels) to be connected to the OXO
Connect via a UA link. This bus allows S0 terminals (S0 sets, PCs equipped with an S0
interface, Fax G4, modem, etc.) to be connected.
The S0 Interface Module can be used alone or combined with Digital Premium DeskPhones.
___change-begin___
 !"#!$% & '#! & ( ) "#!* &             143/160
  
Chapter 4    % 

___change-end___
Figure 4.51: Example of Configuration with an S0 Interface Module
The S0 module provides an S0 bus supplying power. An external power supply (230V AC/48V
DC adapter) is required.
There are two possible operating modes on the S0 bus:
- Non permanent layer: layer 1 must be set up by the calling end (PCX or terminal) at the
start of each call; layer 1 is shut down at the end of the call
- Permanent layer: operation of the S0 bus depends on the direction in which the initial call
was set up:
• If the call was set up from the PCX to the terminal, layer 1 is kept when the call ends.
• If the call was set up from the terminal to the PCX, layer 1 is shut down at the end of
the call. It must be set up again for the following call. If operation is incompatible with
the terminal used, there are two possible solutions: Either layer 2 is kept, this prevents
layer 1 being shut down, or, layer 1 is set up from the PCX by making a call to the
terminal. The call does not need to get through.
4.15.1.2 Compliant Standards
4.15.1.2.1 Safety Requirements
- EN60950: European requirements
- UL 1950: US requirements
- CAN/CSA-C22.2 No 950-95: Canada
4.15.1.2.2 ECM
- EN55022: Limits and methods of measurement of radio interference characteristics of

144/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

information technology equipment

- EN55024: Limits and methods of measurement of immunity characteristics of information
technology equipment
- FCC part15: US requirements
4.15.1.2.3 ISDN
- ETS 300 012: Basic user-network interface layer 1 specification and test principles
- TBR3: Attachment requirements for terminal equipment to connect to an ISDN using ISDN
basic access
- ETS 300 047: Basic access-safety and protection
- I.430: Basic user-network interfaces layer 1 specification
4.15.1.2.4 Environment Classes
- ETS 300 019: Environmental conditions and tests for telecommunication equipment:
• Part 1-1: Storage
• Part 1-2: Transportation
• Part 1-3: Environmental conditions
4.15.1.2.5 Eco Design
ISO 14040: Environmental management – Life cycle assessment – Principles and framework
(1997)

4.16 500 DECT Handset

4.16.1 Hardware description

4.16.1.1 Overview
The 500 DECT just as the other DECT handsets, is particularly useful for users moving within
the workplace.
The 500 DECT offers:
- Access to most of the added value OXO Connect telephone features.
- Enhanced usability with:
• Robust design with inductive charging
• IP 54 compliance (water and dust resistant)
• DECT handset for PWI (alarm button, man down alarm, no movement detector, shock
detector)
• Improved ergonomics
• Integrated bi-antenna
• Backlight display
• Improved quality of audio reception
• Vibrating feature
• MWI (Message Waiting Indication)

 !"#!$% & '#! & ( ) "#!* &             145/160
  
Chapter 4    % 

• Good autonomy (Li-Ion technology)

• Belt clip
The 500 DECT operates with Advanced GAP (AGAP)
The 500 DECT offers:
- A large clear screen accepting images, icons and text
- A simplified functional organization that allows the user to quickly access each of the
mobile's functions
All main operations can be performed on the mobile by use of a single key for navigation (four
directions) and confirmation.
You can take advantage of special DECT features, such as:
- "Roaming", which allows the user to receive or make a call no matter where he/she is
relating to the base station radio coverage zone
- Change of the transmission channel on the base station to portable link during a
conversation due to a change in propagation conditions
- "No-break transfer" from one base station to another when moving during a conversation.
This shift is completely transparent for the user
The set implements specific DECT features, such as:
- Continuous evaluation of different base station levels in order to select the most
appropriate base station for call setup
- Selection of radio transmission channel during call setup
- Continuous listening for paging messages, transmitted by all base stations, when an
incoming call arrives. The set establishes a radio communication with the most appropriate
base station (as it does for an outgoing call)
- Support of the alarm feature, allowing isolated workers to be located with specific alarm
server
Note:
Date/Time infomation is received from OXO Connect whenever 500 DECT registers with OXO Connect.

4.16.1.2 Physical Characteristics

Features 500 DECT

Loudspeaker Yes
Multiline management Yes
Dial-by-name Yes (local and central directory)
Headset connection Yes
(standard wiring)
Backlight display Yes
Backlight Keypad Yes
Vibrator Yes
Navigation/confirm dual-function key Yes
Battery pack Yes

146/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

Features 500 DECT

Color Black
Explosion proof No
Belt clip Yes
Talk time Up to 8 hours
Standby time Up to 100 hours
Charging time Around 9 hours

4.16.1.2.1 Environmental Constraints

Storage, transportation and 500 DECT environment comply with the following standards:
- ETS 300 019 1.1, Storage, Class 1.2: Weather protected, Not temperature controlled
locations
- ETS 300 019 1.2, Transportation, Class 2.3: Public transportation
- ETS 300 019 1.3, In Use, Class 7.2: Portable use, Partly Temperature controlled locations
Operation
- Temperature: to achieve optimum reliability, the ambient temperature must be between
-10°C and +45°C.
- Relative humidity: relative humidity must be between 5% and 95% (without condensation)
Storage
- Temperature: temperature must be between -25°C and +55°C
- Relative humidity: relative humidity must be between 10% and 100% (without
condensation)
4.16.1.3 Description of a Set

 !"#!$% & '#! & ( ) "#!* &             147/160
  
Chapter 4    % 

Figure 4.52: 500 DECT Presentation

This set provides:
1. A colored LED indicator:
• This LED indicator can be customized by the user and can indicate any of the
following:
• Missed call
• Man down
• Low battery
• Alarms, etc...
• The available colors are:
• Red
• Green
• Orange

148/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

2. Display screen with status and call icon

3. Volume adjustment keys
4. Red lateral key: triggers an Alarm Call when the emergency call feature is enabled
5. Call management Key (softkey)
6. Answer the call
7. Headset socket
8. Back light screen: the screen switches automatically after a few seconds of inactivity
9. Navigation/confirm dual-function key
10. Call management key (softkey)
11. Call management key
12. Silent mode key
13. Microphone
4.16.1.4 Keypad
4.16.1.4.1 Main keys

KEY USE
Allows to
- Activate/deactivate the loudspeaker
- Redial from the call log
- Lock/unlock the keypad
Allows to select a function in the Menu and provides access to all
available functions:
- Personal directory
- Company Directory
- Call log
- Handset settings menu
Erase a character
Allows to:
- Validate an action
- Access to shortcuts for navigation
- Activate/deactivate the loudspeaker
- Access the personal directory
- Switch the screen back on
Note:
the four navigator keys are programmable.
Allows to:
- Answer an incoming call
- Start a call
- Switch between two calls (broker call)

 !"#!$% & '#! & ( ) "#!* &             149/160
  
Chapter 4    % 

KEY USE
Allows to:
- Switch the set on/off
- Hang up
- Return to first screen/to previous menu
- Switch off ringer
Silent mode (long pressing)

4.16.1.4.2 Call Icon Display

ICON USE ICON STATUS

Incoming call Icon displayed: Indicates an incoming call.

Outgoing call Icon displayed: Indicates an outgoing call.

Loudspeaker Icon displayed: Indicates the loudspeaker activation.

activated

Silent mode ac- Icon displayed: Indicates the silent mode activation (loudspeaker
tivated off)

Silent micro- Icon displayed: Indicates that the microphone is muted.

phone activ-
ated

4.16.1.4.3 Status Icon

ICON USE ICON STATUS

Battery fully charged (75% - 100%)
Battery Battery half charged (33% - 75%)
Status In- Low battery (0% - 33%)
dicator
Battery completely discharged (0%)

Icon displayed: Indicates the presence of unread text messages.

New text
Message Note:
Text messages are not supported on IBS
New Icon displayed: Indicates the presence of filtered calls.
filtered
message

150/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

Silent Icon displayed: Indicates the silent mode activation.

mode ac-
tivated
Radio re- Indicates the received radio signal level.
ception in-
dicator
Appointe- Icon displayed: Indicates that an appointments reminder is programmed.
ment re-
minder
icon displayed: Indicates the keypad is locked.
Keylock
activation

Missed icon displayed: Indicates a missed incoming call.

call

4.17 8212/8232/8242/8262 DECT

4.17.1 Overview
The 8212 DECT, 8232 DECT, 8242 DECT, and 8262 DECT handsets offer easy-to-use, cost
effective and reliable voice communication solutions that address the mobility needs of
evolving business environments.
They can offer simple and efficient voice communications, enhanced usability and compatibility
with the existing base station portfolio. They also offer all of the OXO Connect value-added
voice services (such as dial-by-name and multi-line management) that are supported by fixed
desk phones.

 !"#!$% & '#! & ( ) "#!* &             151/160
  
Chapter 4    % 

Figure 4.53: 8212 DECT/8232 DECT handset

The 8212 DECT is available in GAP mode for IBS-DECT or IP-DECT sub-systems.
8242 DECT and 8262 DECT sets are very much alike in their appearance, but 8262 DECT
sets offer more advanced features.

152/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

Figure 4.54: 8242 DECT/8262 DECT handsets

The 8262 DECT is available in A-GAP mode for IBS-DECT sub-systems only.

4.17.2 Key benefits

The key benefits of these handsets include:
- Infrastructure investment protection (compatibility with deployed base stations)
- Excellent voice quality and business telephony features throughout the workplace
contributing to improved user responsiveness and productivity
- One Worldwide product
- Automatic band switching for cruise ship application
- Green friendly:
• Economy mode with automatic low radio emission power (25 mW)
• Energy Star™ compliant
• Low power mode (50 mW) for environments such as nuclear facilities
• Long battery life
- Antenna diversity
- Direct micro USB charging
- Notification & Location based services:

 !"#!$% & '#! & ( ) "#!* &             153/160
  
Chapter 4    % 

• Location alarm signal when alarm triggered to help locate user ¬ r ¬

Personal protection features & Location requires an external server.
• up to 4 notification call types from server
• Alarm button (8242 DECT/8262 DECT)
- Task monitoring can be signaled by handset to central server (Hospitality, healthcare,
Warehousing…)

4.17.3 Key features

The key features for the 8212 DECT/8232 DECT/8242 DECT/8262 DECT sets include:
- Advanced GAP (AGAP) protocol
- CAT-iq
- Lightweight, ergonomic design and intuitive operation
- Color display, backlight, vibrator
- Speakerphone and mute
- Headset connection
- Bluetooth 3.0 support (8242 DECT/8262 DECT)
- Loudspeaker/mute during call
- Status led (missed calls, Battery status)
- Received messages audio notification
- Headset jack (3.5 mm)

4.17.4 Location
Designed as a high-end business terminal, the 8242 DECT/8262 DECT terminals provide
notification and location capabilities in addition to a one-button alarm function. With these
features, the 8242 DECT/8262 DECT meet the needs of hospitality, healthcare and any other
professional environments:
- Triangulation with up to 4 DECT base stations
- Data transmitted with Notification messages
- External server required
- Location Audio signal

4.17.5 Technical specifications

4.17.5.1 Mechanical Characteristics

8212 DECT 8232 DECT 8242 DECT 8262 DECT

Dimensions height x width x 5,31 x 1,61 x 5,19 x 2.00 x 5.59 x 2.00 x 5,31 x 1,61 x
depth 0.98 in 0.90 in (132 x 0.90 in. (142 0.98 in
(135.3 x 41.9 51 x 23 mm) x 52 x 23 (135.3 x 41.9
x 25 mm) mm) x 25 mm)

154/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

8212 DECT 8232 DECT 8242 DECT 8262 DECT

Weight 6.06 oz 3.88 oz, 110 4.76 oz, 135 6.06 oz
(172g) grams grams (172g)
Color Black black black Black
Graphic display 1,44 in (36.5 1,4 in, 65k 2.4 in.; 65k 2.4 in. (60,95
mm) colors, 128 x colors; 320 x mm)
resolution 128 pixels 240 pixels resolution:
128 x 128 320 x 240
pixels pixels
64k colors 65k colors
Display backlight White White White White
Keypad backlight Blue Blue Blue Blue
Hands-free, mute Yes Yes Yes Yes
Vibrator No Yes Yes Yes
Headset: Jack 3.5 mm, TRSS Yes Yes Yes Yes
complian
LED status indication 3 colors; Red/ 3 colors; Red/ 4 colors: 4 colors:
Orange/ Orange/ Red/Yel- Red/Yel-
Green Green low/ low/
Blue/Green Blue/Green
Ring tones: 6 user selectable Yes Yes Yes Yes
polyphonic with 4 steps volume
control, meeting mode
Belt clip standard clip standard clip standard clip standard clip
swivel swivel
(option) (option)
Charger Charging on Charging on Charging on Charging on
desktop char- desktop char- desktop char- desktop char-
ger or Micro ger or Micro ger or Micro ger or Micro
USB type B USB type B USB type B USB type B
plug plug plug plug

- Handset MMI languages: English, French, German, Spanish, Italian, Dutch, Portuguese,
Danish, Swedish, Norwegian, Finnish
- System languages: Communication server dependant, 11 languages in GAP/CAT-iq mode
4.17.5.2 Power
Charging on desktop charger or Micro USB type B plug.
Battery pack:
- Li-Ion, easily replaceable, 1100 mAh
- Talk time: up to 11 hours for the 8212 DECT set, up to 20 hours on all other sets
- Standby time:
• 8212 DECT: up to 113 hours
• 8232 DECT: up to 200 hours
• 8242 DECT: up to 160 hours

 !"#!$% & '#! & ( ) "#!* &             155/160
  
Chapter 4    % 

- Charging time: less than 9 hours for the 8212 DECT set, less than 3 hours for all other sets
4.17.5.3 Radio specifications
- DECT
- Frequency range:
• DECT Europe – 1880-1900 MHz
• DECT 6.0 (NA) – 1920-1930 MHz
• DECT Latam – 1910-1930 MHz
except Brazil 1910-1920 Mhz
• DECT Asia - 1900 MHz – 1906 MHz
- Hand-over: Bearer, Connection HO
- Out of coverage signaling
- Antenna diversity
- Automatic band switching for cruise ship applications (requires IP-DECT)
4.17.5.4 Registration
- Up to four systems
- Manual selection
- Automatic selection
- Automatic band switching
4.17.5.5 Audio codecs

8212 DECT 8232 DECT 8242

DECT/8262
DECT
G726 X X X
G722 Wide Band Ready X

4.17.5.6 Features
- Call by name:
• Local & system directory
- Call log (GAP/CAT-iq mode):
• All, Answered, Dialed, Missed
• Up to 50 call logs
- Contacts (GAP/CAT-iq mode):
• Name, up to four numbers per contact
• Up to 50 contacts without SD card
- Hands-free
- Microphone mute
4.17.5.7 Environmental

156/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

For all sets:

- Operation: ETS 300 019 part 1-7 class 7.2
Operating temperature: -10°C to +45°C, (14 to 113°F) ETS 300 019 part 1-7 class 7.2
- Storage: ETS 300 019 part 1-1 class 1.2
Storage temperature: - 25°C to +55°C (-13 to +131°F) ETS 300 019 part 1-1 class 1.2
- Transportation: ETS 300 019 part 1-2 class 2.3
- IP Class: IP40 (EN 60529)
4.17.5.8 Serviceability
For all sets:
- Site survey tool
- Diagnostic mode
- Syslog mode
- Download tool
4.17.5.9 Software management tool
- Download tool
- Flash loader (PC application) - 8232 DECT only
- Parallel FW Update (PFWU tool) - 8242 DECT/8262 DECT only
4.17.5.10 Regulatory

Requirements or norms 8212 DECT 8232 DECT 8242 DECT 8262 DECT
EU Directive
99/5/EEC (R&TTE) X X X X
2006/95/EC (LVD) X X X X
2004/108/EC X X X X
2006/32/EC (Eco Design) X
2009/125/EC (Eco design) X X
RoHS 2011/65/EU X X X X
Safety
IEC 60950-1 X X X X
EN 60950-1 X X X X
UL 60950-1 X X X X
CAN/CSA-22.2 No 60950-1 X X X X
EMC & Radio
EN 301 489-1 X X X X
EN 301 489-6 X X X X
IEC/EN61000-4-2 X X X
Level3 criteria B

 !"#!$% & '#! & ( ) "#!* &             157/160
  
Chapter 4    % 

IEC/EN61000-4-3 X X X X
Level3 criteria A
FCC 47CFR part 15 subpart D X X X X
IC RSS-213 X X X X
DECT
EN 301 406 (TBR6) X X X X
EN 300 176-2 (TBR10) X X
EN 300 175-8 (DECT audio) X X
TBR22 X X
ETSI TS 102 841 (security) X X
DECT security certification program X X
stepA
DECT security certification program X X
stepB
Bluetooth : (Q4 2014) Headset profile
V3.0
EN 301 489-17 X X
EN 300 328 Radio X X
RF AS/NZS4268 X X
FCC part15-C X X
RSS-210 X X
SAR
EN 50360 X X X
EN 50361 X
FCC OET Bulletin 65 X X
SAR value: 0,102W/kg X
IEE 1528 X X X X
RSS-102 X X X
Audio, Hearing Aid
47CFR Part 68 X X X X
Canada CS-03 X X X X
ANSI/TIA/EIA-504 X X
Australia: ACIF S040 X X
Telecom
EN 301 406 (TBR6) X X X
FCC 47CFR part 15 subpart D X X
IC RSS-213 X X
EN 300 176-2 (TBR10) X X
EN 300 175-8 (DECT audio) X X

158/160  !"#!$% & '#! & ( ) "#!* &            
  
    % 

ETS 300 245-2 X X

TBR22 X X
ETSI TS 102 841 (security) X X
ES 202 738 (Group listening) X X
Local regulations
Australia: ACIF S004 X X X X
USA/Canada: FCC 47 part 68 X X X X
New Zealand: PTC200 X X X
Acoustic shocks
UL 1950, ETS 300 245-2 X X
UL 60950-1 Annex NAD X X
EG 202 518 X X

4.17.6 Accessories
The available accessories include:
- Desktop charger: Charges one handset (with USB cable)
- Power supply: Europe, AR, US, UK, Australia plugs
- Spare battery
- Spare belt clip
- Swivel clip
- Vertical pouch
- Horizontal pouch
- Download tool
- Wired headset
- Bluetooth headset (up to four connected audio devices) - 8242 DECT/8262 DECT sets

4.18 PIMphony Reflexes

4.18.1 Detailed description

For more information, you can also consult the PIMphony documentation supplied with
the CD ROM.
The standard OXO Connect offering includes an integrated CTI server (TAPI 2.0) that opens
up a broad range of third party CTI applications.
PIMphony Reflexes is a PC-based workstation equipped with the following PIMphony
applications:
- PIMphony Basic (free of charge)
- PIMphony Pro (requires a software key)

 !"#!$% & '#! & ( ) "#!* &             159/160
  
Chapter 4    % 

- PIMphony Team (requires a software key)

PIMphony Basic PIMphony Pro PIMphony Team
Complete set of telephony YES YES YES
features
Centralized call log YES YES YES
Integration of Contact Hand- YES YES
lers
"Visual Mailbox" interface YES YES
Unified messaging YES YES
Supervision features YES
Assistant Feature YES

For more information about the "Visual Mailbox", interface, consult " Visual Mailbox Interface"
in the "Integrated Voice Server" section.
They are installed from the CD-ROM provided in each system.
PIMphony Pro and PIMphony Team are supplied on a Try and Buy basis. The user can test
both applications free of charge for 2 months.
If PIMphony is emulating an IP workstation, it can be used via a USB or Bluetooth® handset.

160/160  !"#!$% & '#! & ( ) "#!* &