SAMSUNG Confidential

SAMSUNG TFT-LCD

MODEL: LSC320AP04-W

Samsung Display Co., LTD

MODEL LSC320AP04-W Doc. No Page 1 / 24

 SAMSUNG Confidential
General Description

Description
This model uses a liquid crystal display (LCD) of amorphous silicon TFT as switching components. This
model is composed of a TFT LCD panel, a driver circuit, and an ass’y KIT of source PBA. This 32.0”
model has a resolution of a 1366 x 768 and can display up to 16.7 million colors with the wide viewing
angle of 89° or a higher degree in all directions. This panel is designed to support applications by
providing a excellent performance function of the flat panel display such as home-alone multimedia TFT-
LCD TV and a high definition TV.

General Information
Features
 RoHS compliance (Pb-free)
 High contrast ratio & aperture ratio with the wide color gamut
 PVA(patterned vertical align) mode
 Wide viewing angle (±178°)
 High speed response
 FHD resolution (16:9)
 Low power consumption
 DE (Data enable) mode
 The interface (1pixel/clock) of 1ch LVDS (Low voltage differential signaling)
Items Specification Unit Note

Active Display Area 697.6845(H) x 392.256(V) ㎜

Switching Components a-Si TFT Active matrix

TFT : 713.0(H) x 410.5(V)
Glass Size mm ±1.0mm
CF : 713.0(H) x 410.5(V)

713.0(H) x 412.8(V) mm ±1.0mm

Panel Size
1.80(D) mm ±0.2mm

Weight 1100(max1210) g ± 10%

Display Colors 16.7M (True Display) color

Number of Pixels 1,366 × 768 pixel 16 : 9

Pixel Arrangement RGB Horizontal Stripe

Display Mode Normally Black

Surface Treatment 5G N TAC(Anti-Glare),

Haze Haze 4% Typ. 4%
Hardness Hard coating 2H

MODEL LSC320AP04-W Doc. No Page 2 / 24

 SAMSUNG Confidential
1. Absolute Maximum Ratings
If the figures on measuring instruments exceed maximum ratings, it can cause the malfunction or the
unrecoverable damage on the device.

Item Symbol Min. Max. Unit Note

Power supply voltage VDD 10.8 13.2 V (1)

Temperature for storage

TSTG -20 65 ℃ (2),(4)
(Temperature of glass surface)

Operating temperature TOPR 0 50 ℃ (2),(5)

Humidity for storage HSTG 5 90 %RH (2),(4)

Operating humidity HSTG 20 90 %RG (2),(5)

Endurance on static electricity 150 V (3)

Note (1) The power supply voltage at Ta= 25 ± 2 °C

(2) Temperature and the range of relative humidity are shown in the figure below.
a. 90 % RH Max. (Ta ≤ 39 °C)
b. The relative humidity is 90% or less. (Ta ＞39 °C)
c. No condensation
(3) Keep the static electricity under 150V in Polarizer attaching process.
(4) Operating condition with source PCB
(5) Storage temperature condition including glass
(6) Condition without packing. (Unpacking condition)

Fig. Range for temperature and relative humidity

MODEL LSC320AP04-W Doc. No Page 3 / 24

 SAMSUNG Confidential
2. Optical characteristics
The optical characteristics should be measured in the dark room or the space surrounded by the similar setting.
Measuring equipment : TOPCON RD-80S, TOPCON SR-3 ,ELDIM EZ-Contrast
(Ta = 25 ± 2°C, VDD=12.0V, fv=60Hz, fDCLK=78MHz, Light source: D65 Standard light)
Item Symbol Condition Min. Typ. Max. Unit Note

Contrast ratio (1)

C/R 3000 4000 -
(At the center of screen) SR-3
Luminance of white 2 (4)
YL 410 470 - cd/m
(At the center of screen) SR-3

Rx 0.657
Red
Ry Normal 0.332
qL,R=0
Gx qU,D=0 0.285
Green
Chromaticity Gy TYP. 0.586 TYP. (5),(6)
(CIE 1931) Viewing -0.03 +0.03 SR-3
Bx Angle 0.133
Blue
By 0.128
Wx 0.308
White
Wy 0.372
Color gamut - 62 65 - %
Color - 4500 6500 8500 K (5)
SR-3
Viewing
Hor. qL C/R≥10 75 89 -
Angle

qL 75 89 -
Hor.
qR 75 89 - (6)
Viewing
C/R≥10 Degree SR-3
Angle
qU 75 89 - EZ-Contrast
Ver.
qD 75 89 -

Brightness uniformity (2)

Buni 25 %
(9 Points) SR-3
(8)
Gamma 1.9 2.2 2.5
SR3
(7)
transmissivity T 6.3 6.6 %
D65/SR3

Notice
(a) Setup for test equipment
The measurement should be executed in a stable, windless, and dark room for 40min and 60min after
operating the panel at the given temperature for stabilization of the standard light. (SDC uses the standard
luminance of the D65 media).
This measurement should be measured at the center of screen.
The environment condition: Ta = 25 ± 2 °C
(b) D65 media has the general light source.
The temperature of color is 6487K. The coordinate of color is Wx 0.313, Wy 0.329
The luminance of this product is 7217cd/㎡.

MODEL LSC320AP04-W Doc. No Page 4 / 24

 SAMSUNG Confidential

Photo detector Field

SR-3 2°/1°
RD-80S 1°

(c) The CIE positions D65 as the standard daylight illuminant:

[D65] is intended to represent average daylight and has a correlated color temperature of
approximately 6487 K. CIE standard illuminant D65 should be used in all colorimetric calculations
requiring representative daylight, unless there are specific reasons for using a different illuminant.

- Definition of the test point

Note (1) Definition of contrast ratio (C/R)

: The ratio of gray max (Gmax) & gray min (Gmin) at the center point ⑤ of the panel
The measurement goes in D65 Standard light source
G max
C/R
G min
Gmax : The luminance with all white pixels
Gmin : The luminance with all black pixels

Note (2) Definition of the brightness uniformity of 9 points (Test pattern : The full white)
The measurement shall be executed with the standard light source of D65 .

( B max B min)
Buni  100
B max

Bmax : The maximum brightness

Bmin : The minimum brightness

MODEL LSC320AP04-W Doc. No Page 5 / 24

 SAMSUNG Confidential

Note (3) Definition of the response time : Sum of Tr, Tf

Display data

The response
Of optical instruments

※ G-to-G : Average response time between whole gray scale to whole gray scale.
The response time is the value that was measured after it was operated in Samsung's standard BLU for
one hour.( at room temperature)

Note (4) The definition of luminance of white: The luminance of white at the center point ⑤
The measurement shall be executed with the standard light source of D65.

Note (5) The definition of chromaticity (CIE 1931)

The color coordinate of red, green, blue and white at the center point ⑤
The measurement shall be executed with the standard light source of D65.

Note (6) Definition of viewing angle

: The range of viewing angle (C/R ≥10)
The measurement shall be executed with the standard light source of D65.

Note (7) Definition of transmissivity

The measurement shall be executed with the standard light source of D65.

Note (8) Definition of Gamma

Gamma  log( X lum / 100) / log(Y / 100)
X lum  ( Z  Bmin ) / ( Bmax  Bmin )  100

Y: Measurement Level / Z: Measurement Brightness

Bmax: Maximum Brightness / Bmin: Minimum Brightness

MODEL LSC320AP04-W Doc. No Page 6 / 24

 SAMSUNG Confidential
3. Electrical characteristics

3.1 TFT LCD Module

The connector for the display data & timing signal should be connected.
Ta = 25°C ± 2 °C

Item Symbol Min. Typ. Max. Unit Note

Voltage of power supply VDD 10.8 12.0 13.2 V (1)

(a) Black - 400 500 mA

Current
of power (b) White IDD - 500 600 mA (2),(3)
supply
(c) Sub V-Stripe - 600 700 mA

Vsync frequency fV 50 60 66 Hz

Hsync frequency fH 44 48 53 kHz

Main frequency Fdclk 72 78 85 MHz

Rush current IRUSH - - 4 A (4)

Note (1) The ripple voltage should be controlled fewer than 10% of VDD (Typ.) voltage.
(2) fV=60Hz, fDCLK =78MHz, VDD = 12.0V, DC Current.
(3) Power dissipation check pattern (LCD Module only)
a) Black pattern b) White pattern c) V-stripe

(4) Conditions for measurement

The rush current, IRUSH can be measured during TRUSH is 470us

MODEL LSC320AP04-W Doc. No Page 7 / 24

 SAMSUNG Confidential
4. Block diagram

MODEL LSC320AP04-W Doc. No Page 8 / 24

 SAMSUNG Confidential
5. The Pin assignment in the input terminal
5.1. Input signal & power Connector : IS100-L30O-C23 (UJU)

Pin Symbol Description Pin Symbol Description

1 WPN NOTE1 16 GND Ground

2 SCL_I NOTE1 17 LV3_N

3 SDA_I NOTE1 18 LV3_P

4 GND Ground 19 GND Ground

5 LV0_N 20 NC NOTE1

HIGH(3.3V) - NORMAL
6 LV0_P 21 LVDS_SEL
GND - JEIDA

7 GND Ground 22 NC NOTE1

8 LV1_N 23 GND Ground

9 LV1_P 24 GND Ground

10 GND Ground 25 NC NOTE1

11 LV2_N 26 12V DC power supply

12 LV2_P 27 12V DC power supply

13 GND Ground 28 12V DC power supply

14 LVCLK_N 29 12V DC power supply

15 LVCLK_P 30 12V DC power supply

Note (1) No connection: These PINS are used only for the product of SAMSUNG.
(DO NOT CONNECT the input device to these pins.)

MODEL LSC320AP04-W Doc. No Page 9 / 24

 SAMSUNG Confidential
Note (2) Pin number which starts from the left side.

Fig . The diagram of connector

a. Power GND pins should be connected to the LCD’s metal chassis.

b. All power input pins should be connected together.
c. All NC pins should be separated from other signal or power.

Note(3) LVDS OPTION : IF THIS PIN : LOW (GND V)/ NC → JEIDA LVDS FORMAT
OTHERWISE : HIGH (3.3V) → NORMAL NS LVDS FORMAT

Note(4) 46th Pin Aging Enable PIN / IF this Pin HIGH(3.3V)

→ BIST MODE (Rolling Pattern is operated by Only 3.3V input)

MODEL LSC320AP04-W Doc. No Page 10 / 24

 SAMSUNG Confidential
5.2 LVDS Interface
- LVDS receiver : T-con ( 8Bit)
- Data format
LVDS pin JEIDA -DATA Normal-DATA

TxIN/RxOUT0 R2 R0

TxIN/RxOUT1 R3 R1

TxIN/RxOUT2 R4 R2

TxOUT/RxIN0 TxIN/RxOUT3 R5 R3

TxIN/RxOUT4 R6 R4

TxIN/RxOUT6 R7 R5

TxIN/RxOUT7 G2 G0

TxIN/RxOUT8 G3 G1

TxIN/RxOUT9 G4 G2

TxIN/RxOUT12 G5 G3

TxOUT/RxIN1 TxIN/RxOUT13 G6 G4

TxIN/RxOUT14 G7 G5

TxIN/RxOUT15 B2 B0

TxIN/RxOUT18 B3 B1

TxIN/RxOUT19 B4 B2

TxIN/RxOUT20 B5 B3

TxIN/RxOUT21 B6 B4

TxOUT/RxIN2 TxIN/RxOUT22 B7 B5

TxIN/RxOUT24 HSYNC HSYNC

TxIN/RxOUT25 VSYNC VSYNC

TxIN/RxOUT26 DEN DE

TxIN/RxOUT27 R0 R6

TxIN/RxOUT5 R1 R7

TxIN/RxOUT10 G0 G6

TxOUT/RxIN3 TxIN/RxOUT11 G1 G7

TxIN/RxOUT16 B0 B6

TxIN/RxOUT17 B1 B7

TxIN/RxOUT23 RESERVED RESERVED

MODEL LSC320AP04-W Doc. No Page 11 / 24

 SAMSUNG Confidential
5.3 Input signals, basic display colors and the gray scale of each color. (8bit))
DATA SIGNAL
GRAY
DISPLAY
COLOR RED GREEN BLUE SCALE
(8bit)
LEVEL
R0 R1 R2 R3 R4 R5 R6 R7 G0 G1 G2 G3 G4 G5 G6 G7 B0 B1 B2 B3 B4 B5 B6 B7

BLACK 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 -

BLUE 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 -

GREEN 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 -

BASIC CYAN 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
COLOR
RED 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 -

MAGENTA 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 -

YELLOW 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 -

WHITE 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -

BLACK 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R0

1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R1

DARK 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R2
GRAY ↑
SCALE : : : : : : : : : : : : : : : : : : R3~
OF : : : : : : : : : : : : : : : : : : R252
RED ↓
LIGHT 1 0 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R253

0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R254

RED 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R255

BLACK 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 G0

0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 G1

DARK 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 G2
GRAY ↑
: : : : : : : : : : : : : : : : : : G3~
SCALE
OF : : : : : : : : : : : : : : : : : : G252
GREEN ↓
LIGHT 0 0 0 0 0 0 0 0 1 0 1 1 1 1 1 1 0 0 0 0 0 0 0 0 G253

0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 G254

GREEN 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 G255

BLACK 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 B0

0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 B1

DARK 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 B2
GRAY ↑
: : : : : : : : : : : : : : : : : : B3~
SCALE
OF : : : : : : : : : : : : : : : : : : B252
BLUE ↓
LIGHT 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1 1 1 B253

0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 B254

BLUE 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 B255

Note) The definition of gray :

Rn : Red gray, Gn : Green gray, Bn : Blue gray (n = Gray level)
Input signal : 0 = Low level voltage, 1 = High level voltage

MODEL LSC320AP04-W Doc. No Page 12 / 24

 SAMSUNG Confidential
6. Interface timing
6.1 The parameters of timing ( Only DE mode )

SIGNAL ITEM SMBOL MIN. TYP. MAX. Unit NOTE

Clock 1/TC 72 78 85 MHz -

Hsync Frequency FH 44 48 53 KHz -

Vsync FV 50 60 66 Hz -

Active
display TVD - 768 - Lines -
Term for the period
vertical
display
Total vertical TV 780 802 1200 Lines -

Active
display THD - 1366 - Clocks -
Term for the period
horizontal
display
Total TH 1460 1624 2000 clocks -
Horizontal

Note) These products don’t have to receive the signal of Hsync & Vsync from the input device.
(1) Key points when testing: TTL controls the signal and the CLK at the input terminal of LVDS Tx of the
system.
(2) Internal VDD = 3.3V
(3) Spread spectrum
- The limit of spread spectrum's range of SET in which the LCD module is assembled should be within ± 3 %.

MODEL LSC320AP04-W Doc. No Page 13 / 24

 SAMSUNG Confidential
6.2 Timing diagrams of interface signal (Only DE mode )

MODEL LSC320AP04-W Doc. No Page 14 / 24

 SAMSUNG Confidential
6.3 Characteristics of Input data of LVDS

ITEM SYMBOL Min. Typ. Max. UNIT NOTE

Differential input high

VTH - - +100 mV
threshold voltage
VCM= 1.2V
Differential input low
VTL -100 - - mV
threshold voltage

Input common mode voltage VCM 0.3 2.0 V -

Differential Input Voltage |VID| 100 350 600 mV |VID|=100mV

tRSRM - - 450 ps
Input data position FIN=78MHz
tRSLM -450 - ps

Notice The spread spectrum should be 0% when the skew is measured.

Position of a measurement is T-CON LVDS input pin

MODEL LSC320AP04-W Doc. No Page 15 / 24

 SAMSUNG Confidential
6.4 The sequence of power on and off – Sony Model attached Reference file
To prevent a latch-up phenomena or the DC operation of the LCD Module, the power on/off sequence should
be accorded with the settings described in the diagram below.

T1 : The VDD rising time from 10% to 90%

T2 : The time from the point which VDD reach to 90% of voltage to the point which the valid data is out when
the power is on.
T3: The time from the point which the valid data is out to the point which VDD reach to the 90% of voltage
when the power is off.
T4: the time from the point which the Vdd decrease to the point which the Vdd increase again for windows to
restart.

※ The recommended operating condition of the back light system

T5: The time which takes for B/L to be turned on after the signal is entered when the time is on.
T6 : The time which takes until the signal is out after BL is turned off

 The condition of supply voltage to enter in the module from the external system should have
the same condition as the definition of VDD.

 Apply the voltage for the lamp within the range which the LCD operates. when the back light is turned on
before the LCD is operated or when the LCD is turned off before the back light is turned off, the display may
show the abnormal screen momentarily.
 While the VDD is off level, please keep the level of input signals low or keep a high impedance condition.
 The figure of T4 should be measured after the module has been fully discharged between the periods
when the power is on and off.
 The interface signal must not keep the high impedance condition when the power is on.

MODEL LSC320AP04-W Doc. No Page 16 / 24

 SAMSUNG Confidential
7. Outline dimension

7.1 The adhesive size of POL

The next figure shows the size of POL on the drawing sheet attached to the panel for BLU design.

<Figure.>
The POL size of CF : 707.9 X 404.9 ± 0.4mm
The POL size of TFT: 707.9 X 404.9 ± 0.4mm
The total adhesion allowance of POL is ± 0.9㎜
7.2 The drawing sheet for the size of the OLB bonding

MODEL LSC320AP04-W Doc. No Page 17 / 24

 SAMSUNG Confidential

8. Reliability test
8.1 Panel
Item Test Condition Quantity Note
HTOL 60 ℃ (Panel change 500hr / circuit change 250hr) 8
LTOL -5 ℃ (Panel change 500hr / circuit change 250hr) 4
THB 50 ℃ / 90 %RH(Panel change 500hr / circuit change 250hr) 10
ASG
Each
Low Max. frequency 25℃~-40℃ ASG Product Only
Cell
temperature
ASG
Each
High Min. frequency 60℃operation 96hr ASG Product Only
Cell
Temperature
25 ℃ / Mosaic pattern(9*10) 12hrs
Image sticking 8
Rolling pattern 12hrs / 3cycles
Decompressio
-40~50℃, 0m(0ft) ~ 13,700m(45,000ft), 72.5Hr 4
n
HTS 70 ℃, Storage (Panel change 500hr / circuit change 250hr) 4
LTS -25 ℃, Storage(Panel change 500hr / circuit change 250hr) 4
Transportation drop(20cm) → temperature/humidity(-30~60℃ / 40℃ 90%RH)
1pallet
condition → pressure → vibration(5~200Hz 1.05Grms, 2hr) → drop(20cm)
WHTS 60 ℃ / 75 %RH , Storage 4
Noise Electromagnetic noise: Overall 23dB 이하 2
Complex
-20℃~60℃, 0~90%RH, 2cycle 4
stress
S-IC Input ±7KV, Output ±4KV
ESD Output 은 data TP 에 직접 인가 후 진행 3
Input 은 CKV,VCOM 등에 FFC CNT 를 통하여 TEST 를 진행

Item Test condition

Vin Input Surge combination (High impedance)

EOS (optional) step Pass Condition: 5kV under 2

Signal Input Surge combination (High impedance)

step Pass Condition: 120V under

[ Criteria on evaluation]
There should be no change of the product, which may affect to the practical display functions, when the
display quality test is executed under the normal operation setting.
* HTOL/ LTOL : The operating cycle on the high and low temperature
* THB : Temperature humidity slant
* HTS/LTS : The storage at the high and low temperature
* WHTS : The storage in the high temperature with the high humidity

MODEL LSC320AP04-W Doc. No Page 18 / 24

 SAMSUNG Confidential
9. General precautions

9.1 Handling

(a) When the panel kit and BLU kit are assembled, the panel kit and BLU kit should be attached to the
set system firmly by combining each mounted holes. Be careful not to give the mechanical stress.

(b) Be careful not to give any extra mechanical stress to the panel when designing the set, and BLU kit.

(c) Be cautious not to give any strong mechanical shock and / or any forces to the panel kit.
Applying the any forces to the panel may cause the abnormal operation or the damage to the panel
kit and the back light unit kit.

(d) Refrain from applying any forces to the source PBA and the drive IC in the process of the handling
or installing to the set. If any forces are applied to the products, it may cause damage or a
malfunction in the panel kit.

(e) Refrain from applying any forces which cause a constant shock to the back side of panel kit, the set
design and BLU kit. If any forces are applied to the products, it may cause an abnormal display, a
functional failure and etc.

(f) Note that polarizer could be damaged easily.

Do not press or scratch the bare surface with the material which is harder than a HB pencil lead.

(g) Wipe off water droplets or oil immediately. If you leave the droplets for a long time on the product, a
staining or the discoloration may occur.

(h) If the surface of the polarizer is dirty, clean it using the absorbent cotton or the soft cloth.

(i) Desirable cleaners are water or IPA (Isopropyl Alcohol).

Do not use Kenton type materials (ex. Acetone), Ethyl alcohol, Toluene, Ethyl acid or Methyl chloride.
These might cause the permanent damage to the polarizer due to chemical reaction.
(j) If the liquid crystal material leaks from the panel, this should be kept away from the eyes or mouth.
If this contacts to hands, legs, or clothes, you must washed it away with soap thoroughly and see a
doctor for the medical examination.

(k) Protect the panel kit and BLU Kit out of the static electricity. Otherwise the circuit IC could be
damaged.

- Reference : Process control standard of SDC

No. Item Control standard

1 Ionizer All Equipment should be controlled under 150V.(Typ. 100V)

2 Carrying Roller Carrying Roller should be controlled under 200V.

Equipment Ground
3 All Equipment Ground Should be less than 1ohm.
Resistance

MODEL LSC320AP04-W Doc. No Page 19 / 24

 SAMSUNG Confidential

(l) Remove the stains with finger-stalls wearing soft gloves in order to keep the display clean in the
process of the incoming inspection and the assembly process.
(m) Do not pull or fold the source drive IC which connects to the source PBA and the panel or the gate
drive IC.
(n) Do not pull, fold or bend the source drive IC and the gate drive IC in any processes.
If not, the source drive IC could be bent one time in the process of assembling the panel Kit and the
BLU Kit.
(o) Do not adjust the variable resistor located on the panel kit and BLU kit except when adjusting the
flicker.
(p) Do not touch the pins of the interface connector directly with bare hands.
(q) Be cautious not to be peeled off the protection film.

- Make sure to peel off slowly

(It is recommended to peel it off at the speed of more than 8sec.
constantly.)
- The peeling direction is shown at the Fig
- Instruct the ground worker to work with the adequate methods
such as the antistatic wrist band.
- Maker sure to be grounded the source PBA while peeling of the
protection film.
- Ionized air should be blown over during the peeling
- The protection film should not t be contacted to the source drive
IC.
- If the adhesive stains remain on the polarizer after the
protection film is peeled off, please move stains with isopropyl-
alcohol liquid.

(r) The protection film for the polarizer on the panel kit should be slowly peeled off just before using so
that the electrostatic charge can be minimized.
(s) The panel kit and BLU kit have high frequency circuits. The sufficient suppression to the EMI should
be done by the set manufacturers.
(t) The set of which the panel is assembled shall not be twisted. If the product is twisted, it may cause
the damage on the product.
(u) Surface Temp. of IC should be controlled less than 100℃, operating over the Temp. can cause the
damage or decrease of lifetime.

MODEL LSC320AP04-W Doc. No Page 20 / 24

 SAMSUNG Confidential
9.2 Storage

The storage condition for packing

ITEM Unit Min. Max.

Storage
(℃) 5 40
Temperature
Storage
(%rH) 35 75
Humidity
Storage life 6 months
(1) The storage room should provide good ventilation and temperature control.
(2) Products should not be placed on the floor, but on the Pallet away from a wall.
(3) Prevent products from direct sunlight, moisture nor water; Be cautious of a buildup
of condensation.
(4) Avoid other hazardous environment while storing goods.
Storage (5) If products delivered or kept in conditions of the recommended temperature or
Condition
humidity, we recommend you leave them at a circumstance which is shown in the
following table.

period 1 month 2 months 3 months 4 months 5 months 6 months

Baking 50℃, 10%

No Baking 50℃, 10%, 48Hr
Condition 24Hr

9.3 Operation
(a) Do not connect or disconnect the FFC cable during the "Power On" condition.
(b) Power supply should be always turned on and off by the "Power on/off sequence"
(c) The module has high frequency circuits. The sufficient suppression to the electromagnetic interference
should be done by the system manufacturers. The grounding and shielding methods is important to
minimize the interference.
(d) The cables between TV SET connector and Control PBA interface cable should be connected directly
to have a minimized length. A longer cable between TV SET connector and Control PBA interface
cable maybe operate abnormal display
(e) Recommend to age for over 1 hour at least in the state, which the product is driving initially to stabilize
the characteristic of the initial TFT.
(f) Response time depends on the temperature.( In Lower temperature, it becomes longer)

MODEL LSC320AP04-W Doc. No Page 21 / 24

 SAMSUNG Confidential
9.4 Operation condition guide

(a) The LCD product shall be operated under normal conditions.

The normal condition is defined as below;
- Temperature : 20±15℃
- Humidity : 55±20%
- Display pattern : continually changing pattern (Not stationary)

(b) If the product will be used under extreme conditions such as under the high temperature, humidity,
display patterns or the operation time etc.., it is strongly recommended to contact SDC for the
advice about the application of engineering . Otherwise, its reliability and the function may not be
guaranteed. Extreme conditions are commonly found at airports, transit stations, banks, stock
markets, and controlling systems.

9.5 Others

(a) The ultra-violet ray filter is necessary for the outdoor operation.

(b) Avoid the condensation of water which may result in the improper operation of product or the
disconnection of electrode.

(c) Do not exceed the limit on the absolute maximum rating. (For example, the supply voltage
variation, the input voltage variation, the variation in content of parts and environmental
temperature, and so on) If not, panel may be damaged.

(d) If the module keeps displaying the same pattern for a long period of time, the image may be
remained to the screen. To avoid the image sticking, it is recommended to use a screen saver.

(e) This Panel has its circuitry of PCB's on the rear side, so it should be handled carefully in order for a
force not to be applied.

(f) Please contact the SDC in advance when the same pattern is displayed for a long time

MODEL LSC320AP04-W Doc. No Page 22 / 24

 SAMSUNG Confidential
10. Special precautions
10.1 Lists to be cautious when executing the design process
No. Component Expected cause

Prevent the panel from breaking by assigning gaps between the panel and the upholding part for panel on the drawing
Upholding part for
1 for the upholding part for panel.
panel
Refer to the (a), (b), (c) of 3-1 for the design of BLU.

The shape of the Design the upholding part for panel to fit to the panel appropriately when designing the BLU since the shape of the
2 upholding part for upholding part for panel may damage the panel.
panel Refer to the (a), (b), (c) of 3-1 for the design of BLU.

The edge of Design the edge of panel to have a sufficient space with the upholding part for panel when designing the BLU since the
3 upholding part for edge of the upholding part for panel may damage the panel when assembling the panel and BLU.
panel Refer to the (a), (b), (c) of 3-1 for the design of BLU.

Place the upholding part for the panel in order for the shape of mold, which contacts with the panel not to interfere with
Upholding part for
4 the area of panel.
panel
Refer to the (a), (b), (c) of 3-1 for the design of BLU.

Design the BLU in order for the COF not to contain the lead crack resulted from the tensioned COF created when the
5 Drive IC product is twisted if the space between the D-IC COF and the middle mold isn't sufficient.
Refer to the (a), (b), (c),(d),(e),(f), and (g)of 3-2 for the design of BLU.

Design the BLU in order for the product not to contain the lead crack resulted from the tensioned COF caused under the
6 Drive IC condition, which the product is twisted by fixing the source PCB.
Refer to the (a), (b), (c),(d),(e),(f), and (g)of 3-2 for the design of BLU.

1) The temperature of each part of product suggested by our company and the second vendor shall meet the standard
of temperature, which is recommended not to be exceeded by our company when the product is affected under the
IC
7 various temperature ranges.
component
Apply over 1mm long separation distance stated in the safety standard between the electric part and each conductor.
(Apply the rated separation distance when insulating.)

Apply the thermal pad in a designated size to the product as a measure to lower the temperature of heat in order for
8 Thermal pad
each part to use the rated temperature.
The surrounding area of the POL shall be treated with an electrification treatment since the external ESD may cause a
9 POL phenomenon, which the POL is coming off.
In addition, the GND portion of source PBA shall be grounded.

The GND portion of each PBA shall be contacted with the GND portion of BLU.
10 PBA
Refer to the (a) and (b) of 3-3 for the design of BLU.

The standardized approval from the client is required since the EMI is executed by a client.
11 Circuit
Our company can only measure the reference since the client measures the BLU.
The height of
12 Design the BLU with considering the maximum height of parts, which our company suggests.
component
Between the FFC Design the instrument with considering the length between the FFC and the control PBA.
13
and the C-PBA (The marginal minimum length of 5mm or 8mm is required.)
The surface temperature of panel shall be maintained within 0℃ and 45℃ when the external ambient temperature is at
14 Panel
25℃. (Design the BLU with considering the increase of the temperature in the panel by the LED, CCFL, and etc.)
Recommend to age for over 1 hour at least in the state, which the product is driving initially to stabilize the characteristic
15 Aging
of the initial TFT.
The attachment of The additional confirmation by our company is required If the attachment of gasket to the S-PBA of our company is
16
gasket required.(To fix the S-PBA or the EMI)
Design the top chassis and the driver IC to be contacted by placing the shape of emboss inside the top chassis as a
measure to prevent the driver IC from heating. The size of emboss shall be designed in larger size than the size of IC
17 Drive IC
inside the film of the driver IC.
Refer to the (a), (b), (c),(d),(e),(f), and (g)of 3-2 for the design of BLU.
The prohibited Design the BLU in order for the BLU not to interfere with the area, where the control PBA and the source PBA are
18
bandwidth located densely according to the drawing for the BLU from our company.
The material, which contacts with the bottom side of S-PBA which has a pattern shall be non-conducting material or
19 S-PBA
shall be insulated.

MODEL LSC320AP04-W Doc. No Page 23 / 24

 SAMSUNG Confidential

3. Source PCB

MODEL LSC320AP04-W Doc. No Page 24 / 24