General repair notes, suggestions and criticism Page 1 / 7

WWW.ALL-TRANS.BY
ProCarManuals.com

General repair notes, suggestions and criticism

Suggestions and criticism on this Repair Manual

This repair manual

This repair manual was developed for you. It should

support you and offer you assistance. When you use
ELSA , technicians from around the world have the ability
to share their suggestions and criticism, "praise and
blame" .

- Use the Feedback Button - at the top in the Menu

border - .

Information about 6 Spd. Automatic transmission 09D,

general repair notes

Transmission construction and function

More information about the construction and function can

be found in
Self-study program no. 89K303 6 Spd. Automatic
Transmission 09D All Wheel Drive .

Drivetrain guide, overview

 General repair notes, suggestions and criticism Page 2 / 7
WWW.ALL-TRANS.BY
ProCarManuals.com

„ Transfer case

Repair Manual, Rear Final Drive,

Repair Group 34, Transfer case,
removing and installing

Repair Manual, Rear Final Drive,

Repair Group 34, Differential, removing
and installing; Transport of differential

„ Driveshafts

„
 General repair notes, suggestions and criticism Page 3 / 7
WWW.ALL-TRANS.BY

Repair Manual, Rear Final Drive,

Repair Group 39,

„ Rear final drive

Repair Manual, Rear Final Drive,

Repair Group 39,

„ Front final drive

Repair Manual, Rear Final Drive,

ProCarManuals.com

Repair Group 39,

Tools

A complete list of special tools and equipment used in this

repair manual is listed before each repair description and
in: "Special tools catalog" .

With smaller bolts with minimal tightening torques,

uncertainties often exist. Torque wrench 2 to 10 Nm V.A.G
1783 can be used on these bolts.

Transmission

„ If caps are removed from transmission or

transmission has no oil, do not run engine and do
 General repair notes, suggestions and criticism Page 4 / 7
WWW.ALL-TRANS.BY

not tow vehicle.

„ First, always clean connection points and vicinity

and then loosen.

„ When installing transmission, make sure alignment

sleeves are correctly seated between engine and
transmission.

„ Place removed parts on a clean surface. Cover parts

to prevent soiling. Use sheeting or paper. Use lint-
free cloths only!

„ Carefully cover or plug unpacked components if

repairs cannot be performed immediately.
ProCarManuals.com

„ Only install clean parts: Remove packing from

replacement parts immediately prior to installation
and not before.

„ Do not run engine or tow vehicle with oil pan

removed or when there is no ATF in the
transmission.

„ If the transmission is removed from the vehicle,

secure the torque converter to prevent it from falling
out.

„ Before installing transmission, check torque

converter position.

„ Check ATF level after installing 37-4, ATF level,

checking and topping off .

Gaskets, seals

„ Always replace O-rings, gaskets and seals.

„ Once a seal or gasket has been removed, check

contact surface on housing or shaft for burrs and
damage. Repair as necessary.
 General repair notes, suggestions and criticism Page 5 / 7
WWW.ALL-TRANS.BY

„ Before installing a seal, lightly coat outer

circumference and sealing lip with ATF, depending
on the component location.
ProCarManuals.com

„ Only use ATF for automatic transmission

components. Other types of lubrication cause
malfunctions to occur in the transmission hydraulics.

„ Open side of seal faces oil.

„ Check ATF level after installing 37-4, ATF level,

checking and topping off .

Oil

Caution!

Be cautious when dealing with oil. Dispose of drained

oil properly. Consider this: One drop of oil can
contaminate 1000 liters of drinking water.

Do not mix any additives with the oil, and do not add other
oils.

Drained oil must not be used to fill again.

The oil is obtainable as a replacement part. The part

number can be found in Electronic Parts Catalog
"ETKA" .
 General repair notes, suggestions and criticism Page 6 / 7
WWW.ALL-TRANS.BY

Nuts and bolts

„ Loosen and tighten bolts or nuts for securing covers

and housings in diagonal sequence.
ProCarManuals.com

„ The tightening torques stated apply to unoiled bolts

and nuts.

„ Clean threads of bolts that were applied with locking

fluid using a wire brush. Apply locking fluid AMV 185
101 A1 before reinstalling. (Part numbers are for
reference only. Always check with your Parts
Department for the latest part number information).

„ Use thread tap to remove remains of locking fluid

from all threaded holes in which self-locking bolts
are to be installed. Otherwise there is a risk that the
bolts will shear the next time they are removed.

„ Replace self-locking bolts and nuts.

„ The tightening torques stated apply to unoiled nuts

and bolts.

Electrical components
 General repair notes, suggestions and criticism Page 7 / 7
WWW.ALL-TRANS.BY

You have probably received a electrical shock at one time,

when touching a metal item. The reason for this is the
electrostatic charge that is built up in the human body. This
ProCarManuals.com

charge can lead to malfunctions when contacting the

electrical components of the transmission and the gear
selector.

- Touch a grounded object, e.g. a water pipe or a lifting

platform, before working on the electrical components! Do
not make direct contact with connector contacts.

Guided fault finding, On Board Diagnostic (OBD) and

measuring technology

Before performing service work on the transmission, the

cause of damage must be determined as exactly as
possible via "Guided Fault Finding" .

Guided Fault Finding is performed using Vehicle

Diagnosis, Testing and Information System VAS 5051 .
 Transmission identification Page 1 / 2
WWW.ALL-TRANS.BY

00 - 2

Transmission identification
The Touareg is equipped with a 6-speed
Automatic Transmission 09D all-wheel
drive. Allocation 00-3, Code letters,
assembly application .

The transmission code letters are shown

on the type plate on the lower left of the
transmission.
ProCarManuals.com

Example:

„ Code letters

„ Automatic transmission 09D

The transmission code letters

are also shown on the vehicle
 Transmission identification Page 2 / 2
WWW.ALL-TRANS.BY

data plates.
ProCarManuals.com
 Code letters, assembly application Page 1 / 2
Volkswagen Technical Site: http://volkswagen.msk.ru http://vwts.info http://vwts.ru
огромный архив документации по автомобилям Volkswagen, Skoda, Seat, Audi
WWW.ALL-TRANS.BY

Code letters, assembly application

If replacement parts are required for a repair, always refer to transmission code letters of the
automatic transmission.
Automatic transmission 6-speed 09D All Wheel Drive
Code letters "EXL" "EXQ"
Transmission from 05.02 07.02
Installed
to 05.03 05.03
Model in Touareg 2003
Application 3.2 L - 162 kW 5.0 L - 230 kW
Engine
V6 V10 TDI
If replacement parts are required for a repair, always refer to transmission code letters of the
automatic transmission.
Automatic transmission 6-speed 09D All Wheel Drive
Code letters EXP GLK HAP
Transmission from 07.02 07.02 01.04
Installed
ProCarManuals.com

to 08.03 02.04
Model in Touareg 2003
Application 3.2 L -177 kW
Engine
V6
If replacement parts are required for a repair, always refer to transmission code letters of the
automatic transmission.
Automatic transmission 6-speed 09D All Wheel Drive
Code letters "FCS"
Transmission from 07.02
Installed 05.03
to
Model in Touareg 2003
Application 4.2 L - 228 kW
Engine
V8
If replacement parts are required for a repair, always refer to transmission code letters of the
automatic transmission.
Automatic transmission 6-speed 09D All Wheel Drive
Code letters "GLD" "HAQ" HAO does not exist, HAQ is "HZX"
always meant
Transmission from 07.02 11.04 10.05
installed 08.03
to
Model in Touareg 2003
 Code letters, assembly application Page 2 / 2
WWW.ALL-TRANS.BY

5.0 L - 230 kW
Application Engine V10 TDI
If replacement parts are required for a repair, always refer to transmission code letters of the
automatic transmission.
Automatic transmission 6-speed 09D All Wheel Drive
Code letters GLH GLJ GTK
Transmission from 07.02 07.02 01.03
installed
to
Model in Touareg 2003
Application 4.2 L - 228 kW 3.2 L - 162 kW 5.0 L - 230 kW
Engine V8 V6 V10 TDI
If replacement parts are required for a repair, always refer to transmission code letters of the
automatic transmission.
Automatic transmission 6-speed 09D All Wheel Drive
Code letters HAM "HAU"
Transmission from 01.04 01.04
installed
to
ProCarManuals.com

Model in Touareg 2003

3.2 L - 162 kW 4.2 L - 228 kW
Application V6 V8
Engine 3.2 L - 177 kW
V6
If replacement parts are required for a repair, always refer to transmission code letters of the
automatic transmission.
Automatic transmission 6-speed 09D All Wheel Drive
Code letters "HPH" HZV JBR
Transmission from 11.05 11.05 11.05
installed
to
Model in Touareg 2003
Application 4.2L - 257 kW 4.2 L - 228 kW 3.2 L - 177 kW
Engine V8 - FSI V8 VR6
 Capacities Page 1 / 1
WWW.ALL-TRANS.BY

00 - 4

Capacities

Further information about Volkswagen oils can be found in:

Fluid Capacity Chart

Capacities Automatic transmission 09D

ProCarManuals.com

Initial filling at manufacturer approx. 9 L

(filled for life)
Lubricant ATF
Replacement part number:
Electronic parts catalog "ETKA"
 Torque converter Page 1 / 3
WWW.ALL-TRANS.BY

32 - 1

Torque converter
Torque converter, checking
ProCarManuals.com

- Check converter hub for wear grooves - arrow - .

Torque converter is welded and must be replaced if

damaged.

Torque converter gaskets, removing and installing

Special tools, testers and auxiliary items required

„ Extractor lever VW 681

 Torque converter Page 2 / 3
WWW.ALL-TRANS.BY

„ Thrust piece 3295

Removing

- Insert extractor lever VW 681 directly behind the sealing

lip of sealing ring, so that the contact ring which is behind it
is not damaged.
ProCarManuals.com

Installing

- Coat outer circumference and sealing lips of sealing ring

with ATF.

Installation position:

The open side of sealing ring faces transmission.

- Using thrust piece 3295 , drive in sealing ring for torque

converter up to thrust piece stop.

Torque converter, draining

Special tools, testers and auxiliary items required

„ Oil extraction device V.A.G 1358 A

„ Oil extraction sensor V.A.G 1358 A/1

 Torque converter Page 3 / 3
WWW.ALL-TRANS.BY

In case of soiling of the ATF via shavings or during a major

transmission overhaul, torque converter must be drained
as follows:

- Extract ATF from torque converter using oil extractor

V.A.G 1358 A and oil extractor probe V.A.G 1358 A .
ProCarManuals.com

Torque converter, installing

- Press torque converter hub through oil seal as far as first

stop.

- Lightly press torque converter inwards and turn until slots

on torque converter hub engage in drive lugs on ATF pump
gear and torque converter slides in a noticeable distance.

Caution!

If the torque converter is not properly installed, the

drive lugs on the torque converter and the ATF pump
will be severely damaged when the transmission is
attached to the engine.

- After "feeling" the converter slide in as far as top, pull it

back about 5 mm.

This brings the sealing lip back into its "correct location" if it
was disturbed during installation.

Before tightening the connecting bolts of the

engine/transmission, check that the torque converter
can be turned behind the drive plate, and keep
checking when tightening the bolts.

If the torque converter cannot be turned, it should be

assumed that it is not properly installed. The drive
plate surface and the ATF pump will be damaged.

- After installing transmission, check ATF level and top off

37-4, ATF level, checking and topping off .
 Tester , connecting Page 1 / 3
WWW.ALL-TRANS.BY

37 - 1

"Tester" , connecting
Volkswagen offers various testers, for example:

„ Vehicle Diagnosis, Testing and Information System

VAS 5051

„ Vehicle Diagnosis, Testing and Information System

VAS 5051B

„ Tester VAS 5051/11A

„ Vehicle Diagnosis and Service Syst. VAS 5052

„ Diagnosis System VAS 5053

ProCarManuals.com

The operation of this "tester" is described in the respective

operating instructions.

The following description is based on the Vehicle

Diagnosis, Testing and Information System VAS 5051
37-1, Vehicle Diagnosis, Testing, and Information System
VAS 5051 , connecting .

Vehicle Diagnosis, Testing, and Information System VAS

5051 , connecting

Special tools, testers and auxiliary items required

„ Vehicle Diagnosis, Testing and Information System

VAS 5051

Warning!
 Tester , connecting Page 2 / 3
WWW.ALL-TRANS.BY

„ During a test drive you must always secure

testing and measuring equipment on the back
seat.

„ These devices may only be operated by a

passenger during a test drive.
ProCarManuals.com

- Plug connector of diagnostic cable VAS 5051/1 or VAS

5051/3 into vehicle Data Link Connector (DLC).

- Turn on tester - arrow - .

"Tester" is ready for operation when you can select

between fields/buttons Guided Functions and Guided
Fault Finding at "right" of display.

Depending on equipment and tester version, additional

functions may be "displayed" , for example:

„ ElsaWin

„ Measuring Technique

„ On Board Diagnostic (OBD)

 Tester , connecting Page 3 / 3
WWW.ALL-TRANS.BY

"Tester" is not ready for operation.

- Switch on ignition.

- Touch a field/button on display to start desired function.

ProCarManuals.com
 Selector mechanism, servicing Page 1 / 26
WWW.ALL-TRANS.BY

37 - 2

Selector mechanism, servicing

Warning!

Shift selector lever into position "P" and engage foot

operated parking brake before working with the engine
running.

Selector mechanism, checking

In selector lever positions "R" , "D" and "S" , the starter

motor will not operate.

For speeds exceeding 5 km/h and shifting into selector

lever position "N" , the shift lock solenoid must not engage
to lock selector lever. Selector lever can be shifted into
driving gear.

For speeds below 5 km/h (almost standstill) and shifting

into selector lever position "N" , the shift lock solenoid must
ProCarManuals.com

only engage after approx. 1 second. Selector lever can

only be shifted out of position "N" with the brake pedal
operated.

Selector lever in position "P" and ignition switched on

„ Brake pedal not depressed:

Selector lever is locked and cannot be switched out of

position "P" with press button depressed Solenoid for
selector lever lock blocks selector lever.

„ Brake pedal depressed:

Solenoid for selector lever lock releases selector lever. It is

possible to shift into a driving gear. Switch selector lever
slowly through from "P" to "S" ; while doing this check
whether selector lever position in instrument cluster
matches selector lever position.

Selector lever in position "N" and ignition switched on

„ Brake pedal not depressed:

Selector lever is locked and cannot be switched out of

position "N" with press button depressed Solenoid for
selector lever lock blocks selector lever.

„ Brake pedal depressed:

 Selector mechanism, servicing Page 2 / 26
WWW.ALL-TRANS.BY

Solenoid for selector lever lock releases selector lever. It is

possible to shift into a driving gear.

Selector lever in "Tiptronic" position

„ Move selector lever into Tiptronic gate:

The illumination of the "D" symbol must go out in selector

mechanism cover and the "+" and "-" symbols must light
ProCarManuals.com

up.

The selector lever display in instrument cluster must

change from "P R N D S" to "6 5 4 3 2 1" when selector
lever is moved in Tiptronic gate.

Ignition and light switched on

Respective symbol in selector mechanism cover lights up.

Transmission Range (TR) Display

Simultaneous lighting of all segments of Transmission

Range (TR) selector lever display indicates transmission in
emergency running mode.

- Check and adjust selector lever cable 37-2, Selector

lever cable, checking and adjusting .

Selector mechanism, disassembling and assembling

 Selector mechanism, servicing Page 3 / 26
WWW.ALL-TRANS.BY
ProCarManuals.com

„ Selector lever handle

„ Removing and installing

37-2, Selector lever handle,
removing and installing

„ Clip

„ Trim strip

„ Emblem

„ Self-adhesive

„ Sleeve

„ Cover

„ With selector indicator

 Selector mechanism, servicing Page 4 / 26
WWW.ALL-TRANS.BY

„ Printed circuit board

„ With Tiptronic Switch F189

„ Frame

„ With cover strips

„ With "opposite pole" /signal

magnet for Tiptronic Switch
F189

„ Harness

„ Removing and installing

37-2, Selector Lever Park
Position Lock Switch F319 ,
removing and installing
ProCarManuals.com

„ Shift lock solenoid N110

„ Removing and installing

37-2, Shift lock solenoid
N110 , removing and
installing

„ Selector lever park position

solenoid N380

„ Removing and installing

37-2, Shifting selector lever
out of P without electricity
(Manual release)

„ Bolt, 20 Nm

„ Qty. 4

„ Bracket

„ Bracket

„ Selector mechanism

„ With shift lock solenoid

N110 and selector lever park
position solenoid N380

„ Can be removed upward

 Selector mechanism, servicing Page 5 / 26
WWW.ALL-TRANS.BY

„ Bolt

„ Adjusting 37-2, Adjusting

„ Mounting bracket/cover

„ Can only be removed

downward

„ Lock washer

„ Always replace

„ Selector lever cable

„ Is removed together with

selector mechanism Item
- 15 -

Adjusting 37-2, Adjusting

ProCarManuals.com

„ Lock washer

„ Always replace

„ Mounting bracket

„ For selector lever cable on

transmission

„ Bolt, 23 Nm

„ Self-locking

„ Always replace

„ The threaded holes in

transmission for bolts must
always be cleaned. (e.g. with
a thread tap)

Selector lever handle, removing and installing

Removing

To ensure the handle is not damaged adhere to this

sequence:
 Selector mechanism, servicing Page 6 / 26
WWW.ALL-TRANS.BY

- Pry out selector.

ProCarManuals.com

- Remove bracket from handle.

- Pull button passed pressure point until it is locked in

position.

- Remove handle from selector lever.

Installing

If the handle is replaced, do not remove the assembly aid

from the new handle under any circumstances!

If the button is inadvertently pressed into the handle, hold

handle vertically and at the bottom (!). Carefully blow
button outwards again using compressed air until it can be
pulled out over the pressure point by hand.
 Selector mechanism, servicing Page 7 / 26
WWW.ALL-TRANS.BY

- Re-install assembly aid - A - (enclosed with new

handle).

- Push in clip.

- Press selector into handle again.

- Place selector lever in position "N" .

ProCarManuals.com

- I - Guide sleeve carefully through cover strip and cross

slide lying underneath.

- Make certain that the sleeve is carefully guided through

the cover strip when inserting. If carelessly pushing the
sleeve in, the cover strip will break.

- II - Install handle lengthwise until stop, then turn.

Installation position: Button facing driver.

- III - Press handle on selector lever up to stop until it

engages noticeably.

- Remove assembly aid - A - , operate switch and remove

sleeve upward.

- Remove protective foil on adhesive surface and affix

label - arrow - .
 Selector mechanism, servicing Page 8 / 26
WWW.ALL-TRANS.BY

Selector lever cable, checking and adjusting

Special tools, testers and auxiliary items required

„ Torque wrench V.A.G 1331

ProCarManuals.com

„ Socket and key T40031

Checking

- Place selector lever in position "P" .

- Remove noise insulation on bottom of transmission.

- Pull selector lever cable - 2 - from lever/selector shaft.

 Selector mechanism, servicing Page 9 / 26
WWW.ALL-TRANS.BY

- Shift selector lever from "P" to "S" .

„ Selector mechanism and selector lever cable must

have freedom of movement during this, replace
selector lever cable or shift mechanism if necessary.

- Place selector lever in position "P" .

- Shift lever/switch rod at transmission in "P" position.

Catch must engage in parking lock gear, both front wheels
are locked (cannot be turned together in one direction).

„ It must be possible to push selector lever cable onto

lever/shift rod, if necessary adjust selector lever
cable.

- Carefully press selector lever cable onto selector shaft

lever. Do not bend lever/selector shaft when doing this,
otherwise shifting can no longer be adjusted precisely.

- Adjust selector lever cable 37-2, Adjusting .

ProCarManuals.com

Adjusting

Special tools, testers and auxiliary items required

„ Socket and key T40031

„ Selector lever cable is disconnected from selector

shaft lever.

- Place selector lever in position "S" .

- Move selector shaft lever to position "D" on

transmission.

- Remove selector lever handle 37-2, Selector lever

handle, removing and installing .
 Selector mechanism, servicing Page 10 / 26
WWW.ALL-TRANS.BY

- The procedure for disconnecting batteries must

absolutely be obeyed.

- Disconnect battery Ground (GND) strap with ignition

switched off

Repair Manual, Electrical Equipment, Repair Group 27,

- Remove ashtray and remove shift mechanism cover from

center console

Repair Manual, Body Interior, Repair Group 68,

- Remove cover from shift mechanism 37-2, Cover,

ProCarManuals.com

removing and installing .

- Remove frame from shift mechanism 37-2, Frame,

removing and installing .

- Loosen clamping bolt approx. one turn on selector lever

cable.

- Carefully push selector lever cable onto the lever/selector

shaft. When doing this, take care not to bend the
lever/selector shaft, otherwise the selector mechanism will
no longer be able to be adjusted correctly.

- Center selector lever by slightly moving selector lever

forward and backward in position "D" without leaving
position "D" .

- Tighten clamping screw to 10 Nm in this position. Socket

insert T40031 can be used for this.
 Selector mechanism, servicing Page 11 / 26
WWW.ALL-TRANS.BY

Further installation is in reverse order of removal.

- Install ashtray and selector mechanism cover in center

console

Repair Manual, Body Interior, Repair Group 68,

- Connect battery.

- Observe work sequence after connecting the battery

Repair Manual, Electrical Equipment, Repair Group 27,

.
ProCarManuals.com

Selector lever cable, removing and installing

Note:

„ Tying a line to the cable before removing it, will

make it possible to thread the cable back in when
installing Topic 00-1 .

Removing

- Remove shift mechanism 37-2, Selector mechanism,

removing and installing .

- Push boot - arrow - forward and out from shift unit.

To remove selector lever cable, the transfer case only

needs to be lowered.

- Lower transfer case

 Selector mechanism, servicing Page 12 / 26
WWW.ALL-TRANS.BY

Repair Manual, Rear Final Drive, Repair Group 34,

Transfer case, removing and installing

.
ProCarManuals.com

- Remove locking washer - 1 - .

- Pull selector lever cable - 2 - from lever/selector shaft.

Installing

- Insert selector lever cable into shift unit - 1 - .

- Seat sleeve - 2 - so that it makes full contact against

shift unit.

- Install the transfer case

Repair Manual, Rear Final Drive, Repair Group 34,

.
 Selector mechanism, servicing Page 13 / 26
WWW.ALL-TRANS.BY

- Carefully press selector lever cable - 2 - onto selector

shaft lever. Do not bend lever/selector shaft when doing
this, otherwise shifting can no longer be adjusted
precisely.

- Replace lock washer - 1 - .

ProCarManuals.com

- Seat boot - arrow - so that it makes full contact against

shift unit.

- Install shift mechanism 37-2, Selector mechanism,

removing and installing .

Cover, removing and installing

Removing

- Remove selector lever handle 37-2, Selector lever

handle, removing and installing .

- The procedure for disconnecting the battery must

absolutely be obeyed.

- Disconnect battery Ground (GND) strap with ignition

switched off
 Selector mechanism, servicing Page 14 / 26
WWW.ALL-TRANS.BY

Repair Manual, Electrical Equipment, Repair Group 27,

- Remove cover from center console

Repair Manual, Body Interior, Repair Group 68,

.
ProCarManuals.com

- Disconnect connector - 1 - .

- Carefully pull off retaining clips - 2 - on left and right from

frame.

Installing

Installation is in reverse order of removal. Note the

following:

- Install cover to center console

Repair Manual, Body Interior, Repair Group 68,

- Connect battery

Repair Manual, Electrical Equipment, Repair Group 27,

- Install selector lever handle 37-2, Selector lever

handle, removing and installing .
 Selector mechanism, servicing Page 15 / 26
WWW.ALL-TRANS.BY

Frame, removing and installing

Removing

- Remove cover 37-2, Cover, removing and installing .

- Pull retaining clips - arrows - outward on left and right

and remove frame upward.
ProCarManuals.com

Installing

Installation is in reverse order of removal.

- Install cover 37-2, Cover, removing and installing .

Shifting selector lever out of "P" without electricity

(Manual release)

- Press solenoid core in direction of - arrow - from above

with a "long, thin" screwdriver.

The handle does not need to be removed for this.

 Selector mechanism, servicing Page 16 / 26
WWW.ALL-TRANS.BY

Selector lever park position solenoid N380 , removing

and installing

Removing

- Remove shift mechanism 37-2, Selector mechanism,

removing and installing .

- Release connector and pull off.

ProCarManuals.com

- Release solenoid from its mounting and pull it upward

and out from locking lever - 1 - and shift mechanism.

Installing

- Set solenoid lever - 2 - vertically.

- Set solenoid into mount of shift mechanism at a slight

angle.

- Attach lever - 2 - to locking lever - 1 - .

 Selector mechanism, servicing Page 17 / 26
WWW.ALL-TRANS.BY

- Push solenoid into shift mechanism until limit stop, and it

is locked into its mounting - arrow - .

- Make sure that the solenoid is locked in its mount -

arrow - up to the limit stop and lever - 2 - engages
ProCarManuals.com

locking lever - 1 - .

Shift lock solenoid N110 , removing and installing

Removing

- Remove shift mechanism 37-2, Selector mechanism,

removing and installing .

- Release connector and remove

- Release solenoid from its mounting and pull straight out

from locking lever - 1 - and shift mechanism.

Installing
 Selector mechanism, servicing Page 18 / 26
WWW.ALL-TRANS.BY

- Set solenoid lever - 2 - upward vertically.

- Push solenoid into mount of shift mechanism from front.

ProCarManuals.com

- Attach lever - 2 - to locking lever - 1 - .

- Push solenoid into shift mechanism until limit stop, and it

is locked into its mounting - arrow - .

- Make sure that the solenoid is locked in its mount -

arrow - up to limit stop and lever engages locking lever.

Selector Lever Park Position Lock Switch F319 ,

removing and installing

The Tiptronic switch F189 is integrated into the wiring

harness for both solenoids.

Special tools, testers and auxiliary items required

 Selector mechanism, servicing Page 19 / 26
WWW.ALL-TRANS.BY

„ Torque wrench V.A.G 1783

Removing

- Remove selector lever handle 37-2, Selector lever

handle, removing and installing .

- The procedure for disconnecting the battery must

ProCarManuals.com

absolutely be obeyed.

- Disconnect battery Ground (GND) strap with ignition

switched off

Repair Manual, Electrical Equipment, Repair Group 27,

- Remove cover from center console

Repair Manual, Body Interior, Repair Group 68,

- Remove bolts - arrows - from center console.

 Selector mechanism, servicing Page 20 / 26
WWW.ALL-TRANS.BY

- Release connector - 1 - and remove.

- Remove bolt - 2 - and remove retainer.

- Pull connector - 3 - out from retainer.

- Disconnect connectors from solenoids.

ProCarManuals.com

- Press securing lever toward right and pull button upward

out of shift mechanism.

Installing

Installation is in reverse order of removal. Note the

following:
 Selector mechanism, servicing Page 21 / 26
WWW.ALL-TRANS.BY

- Route wiring harnesses - 1 - to - 3 - as shown in

illustration.

1 - Wiring harness to shift lock solenoid N110

2 - Wiring harness to selector lever park position solenoid
N380
3 - Wiring harness to Selector Lever Park Position Lock
Switch F319
ProCarManuals.com

- Press connector - 3 - into retainer.

- Fasten bolt - 2 - .

- Connect connector - 1 - .

- Install cover to center console

Repair Manual, Body Interior, Repair Group 68,

- Connect battery

Repair Manual, Electrical Equipment, Repair Group 27,

- Install selector lever handle 37-2, Selector lever

handle, removing and installing .

Selector mechanism, removing and installing

Special tools, testers and auxiliary items required

 Selector mechanism, servicing Page 22 / 26
WWW.ALL-TRANS.BY

„ Torque wrench V.A.G 1331

ProCarManuals.com

„ Socket and key T40031

Removing

- Remove selector lever handle 37-2, Selector lever

handle, removing and installing .

- Pull pull-rod up and shift selector lever to position "S" .

Note:

„ The procedure for disconnecting the battery must

absolutely be obeyed.

- Disconnect battery Ground (GND) strap with ignition

switched off

Repair Manual, Electrical Equipment, Repair Group 27,

- Remove center console

 Selector mechanism, servicing Page 23 / 26
WWW.ALL-TRANS.BY

Repair Manual, Body Interior, Repair Group 68,

- Remove sound insulation from center console.

ProCarManuals.com

- Release connector - 1 - and pull off.

- Remove bolt - 2 - and remove retainer.

- Pull connector - 3 - out from retainer.

- Disconnect connector - 1 - .

- Carefully pull off retaining clips - 2 - on left and right from

frame.
 Selector mechanism, servicing Page 24 / 26
WWW.ALL-TRANS.BY

- Pull retaining clips - arrows - outward on left and right

and remove frame upward.
ProCarManuals.com

- Remove clamping bolt at selector lever cable using

socket and key T40031 .

- Remove bolts - 1 - and remove front retainer - 2 - for

shift mechanism.

- Remove rear retainer for shift mechanism.

- Remove shift mechanism with selector lever cable

slightly rearward.
 Selector mechanism, servicing Page 25 / 26
WWW.ALL-TRANS.BY

- Remove lock washer - 2 - from selector lever cable - 1 -

and pull shift mechanism off from selector lever cable.

Installing

Installation is in reverse order of removal. Note the

following:
ProCarManuals.com

- Attach selector lever cable - 1 - and fasten using a new

lock washer - 2 - .

- Fasten front and rear retainers for shift mechanism

Item - 12 - .

- Route wiring harnesses - 1 - to - 3 - as shown in the

illustration.
 Selector mechanism, servicing Page 26 / 26
WWW.ALL-TRANS.BY

1 - Wiring harness to shift lock solenoid N110

2 - Wiring harness to selector lever park position solenoid
N380
3 - Wiring harness to Tiptronic switch F189

- Press connector - 3 - into retainer.

- Fasten bolt - 2 - .
ProCarManuals.com

- Connect connector - 1 - .

- Adjust selector lever cable 37-2, Selector lever cable,

checking and adjusting .

- Install center console

Repair Manual, Body Interior, Repair Group 68,

- Connect battery

Repair Manual, Electrical Equipment, Repair Group 27,

- Install selector lever handle 37-2, Selector lever

handle, removing and installing .
 Transmission, removing and installing Page 1 / 12
WWW.ALL-TRANS.BY

37 - 3

Transmission, removing and installing

Transmission (vehicles with V6 gasoline engines, V8
gasoline engines and V10 TDI engines), removing and
installing

Description:

The automatic transmission - 09D - is removed together

with the engine, front final drive and transfer case. The
procedure for this is described in the engine assembly
group.

For all engine variations of the Touareg, including the one

ProCarManuals.com

that is being serviced, it is advisable to remove the "lower

connecting bolts" of the engine/transmission, even before
the removal of the gear set. When possible, the torque
converter fasteners should also be mounted early on. This
applies when removing, as well as when installing the
transmission.

It gives two variations; separating engine and transmission

from each other on the scissor lift table VAS 6131 :

First version

The automatic transmission - 09D - and transfer case - 1

- remain fastened to each other. They can be removed
from engine together, for example, for removing and
installing the torque converter.

For this, only disconnect front driveshaft - 2 - from transfer

case. This way, when separating, the engine can be placed
on one side of scissor lift table VAS 6131 and both
transmissions on other side.

Second version

First, the transfer case is removed from the table, then the
automatic transmission. This way, repairs can be
performed on the automatic transmission. For this, first the
front driveshaft must be loosened on both sides, the
transfer case - 1 - must be flanged off and removed from
table. Then, flange off automatic transmission from engine
and remove it from the table, if necessary.

This "second version" is described here.

 Transmission, removing and installing Page 2 / 12
WWW.ALL-TRANS.BY
ProCarManuals.com

„ Transfer case

„ Precautions and tightening

torques for servicing the
transfer case and driveshafts

Repair Manual, Rear Final Drive,

Repair Group 34,

„ Driveshafts, front and rear

„ Rear final drive

„ Front final drive

 Transmission, removing and installing Page 3 / 12
WWW.ALL-TRANS.BY

Removing

- For all engine variations, it is advisable to remove the

"lower connecting bolts" of the engine/transmission, even
before the removal of the gear set.

When possible, the torque converter fasteners should also

be mounted early on.
ProCarManuals.com

- Remove engine with transmission

Repair Manual, Engine Mechanical, Repair Group 10,

Vehicles with V6 and V8 gasoline engines

- Remove starter motor

Repair Manual, Electrical Equipment , Repair Group 27,

- Remove torque converter from drive plate.

 Transmission, removing and installing Page 4 / 12
WWW.ALL-TRANS.BY

Vehicles with V10 TDI

- Remove starter cable so far until bolt - arrow - can be

removed
ProCarManuals.com

Repair Manual, Electrical Equipment, Repair Group 27,

On these models, the torque converter fasteners and the

lower engine/transmission bolts should be installed with the
gear set mounted.

Make sure that at least two plates VAS 6131/1 on the

lifting table are placed under oil pan as support for
automatic transmission.

- Remove driveshaft between transfer case and front final

drive.

- To counter-hold the driveshaft, the counter-hold tool

T10172 can be used.
 Transmission, removing and installing Page 5 / 12
WWW.ALL-TRANS.BY

- The counter-holder 3435 with two bolts up to M10 is also

recommended.

or: Retainer T10172

ProCarManuals.com

- Support transfer case with crane.

- Separate transfer case and set aside

Repair Manual, Rear Final Drive, Repair Group 34,

Before engine and transmission are separated from each

 Transmission, removing and installing Page 6 / 12
WWW.ALL-TRANS.BY

other, secure engine from tipping over.

- If a second crane is not available, separate the engine

and transmission and then support the engine with
available materials.

- Support transmission with crane 37-3, Transmission,

transporting .

- Loosen ATF lines 37-5, ATF lines and ATF cooler .

- Remove all connecting bolts for engine/transmission.

- Carefully press transmission off engine.

- Make sure that the converter is also pressed from drive

plate with transmission.

Installing
ProCarManuals.com

Installation is in reverse order of removal.

- Check adjustment of selector lever cable and adjust if

necessary 37-2, Selector lever cable, checking and
adjusting .

After installation, check the ATF level, if necessary top off

37-4, ATF level, checking and topping off and check the
vehicle alignment

Repair Manual, Suspension, Wheels, Steering, Repair

Group 44,

Tightening torques, vehicles with V6 gasoline engine

Topic 37-3 .

Tightening torques, vehicles with V8 FSI gasoline engine

(FSI) Topic 37-3 .

Tightening torques, vehicles with V8 gasoline engine (TSI)

Topic 37-3 .

Tightening torques, vehicles with V10 TDI Topic 37-3 .

Torque specifications

Vehicles with V6 gasoline engine

 Transmission, removing and installing Page 7 / 12
WWW.ALL-TRANS.BY
ProCarManuals.com

Alignment sleeves - arrows -

Bolt Component location by "clock" Nm

M 12 x 60 11.00 o'clock 80
M 12 x 60 12.00 o'clock 80
M 12 x 60 2.00 o'clock 80
with bracket
M 12 x 70 3.00 o'clock 80
M 12 x 60 3.00 o'clock 65
in starter
M 12 x 60 3.30 o'clock 65
at starter
M 10 x 50 4:00 o'clock 45
5:30 o'clock
6:30 o'clock
8:00 o'clock
 Transmission, removing and installing Page 8 / 12
WWW.ALL-TRANS.BY

M 12 x 140 8.00 o'clock 80

M 12 x 155 9.00 o'clock 80
with nut
Drive plate to converter 85

Vehicles with V8 FSI engine (FSI)

ProCarManuals.com

Alignment sleeves - arrows -

Bolt Component location by "clock" Nm

M 12 x 60 12.00 o'clock 80
(Qty. 2)
M 12 x 70 2.00 o'clock 80
with bracket
M 10 x 205 2.30 o'clock 45
at starter
M 12 x 80 4.00 o'clock 65
 Transmission, removing and installing Page 9 / 12
WWW.ALL-TRANS.BY

M 12 x 45 5.00 o'clock 80
M 12 x 45 7.00 o'clock 80
M 12 x 70 8.00 o'clock 80
with bracket
M 12 x 70 10.00 o'clock 80
with bracket
Drive plate to converter 85

Vehicles with V8 Turbo gasoline engine (TSI)

ProCarManuals.com

Alignment sleeves - arrows -

Drive plate to torque converter "qty. 6" 85

Nm.

Bolt Component location by "clock" Nm

M 12 x 85 12.00 o'clock 80
M 12 x 85 1.00 o'clock 80
 Transmission, removing and installing Page 10 / 12
WWW.ALL-TRANS.BY

M 12 x 85 2.00 o'clock 80
M 10 x 70 03:00:00 AM o'clock 65
(Qty. 2) 04:00:00 AM o'clock 65
(starter)
M 10 x 70 5:00 o'clock 45
6:00 o'clock 45
7:00 o'clock 45
M 12 x 85 8.30 o'clock 80
M 12 x 70 9.30 o'clock 80
Drive plate to torque converter "Qty. 6" 85

Vehicles with V10 TDI

ProCarManuals.com

Alignment sleeves - arrows -

Bolt Component location by "clock" Nm

M 12 x 140 12.00 o'clock 80
 Transmission, removing and installing Page 11 / 12
WWW.ALL-TRANS.BY

M 12 x 180 1.00 o'clock 80

M 12 x 155 2:00 o'clock 65
3:30 o'clock 65
(starter)
M 12 x 85 4:00 o'clock 80
5:00 o'clock 80
7:00 o'clock 80
M 12 x 80 8.00 o'clock 80
with bracket
M 12 x 140 8:30 o'clock 80
10:00 o'clock 80
Drive plate to converter 60

Transmission, transporting
ProCarManuals.com

Special tools, testers and auxiliary items

required

„ Lifting tackle 2024 A

 Transmission, removing and installing Page 12 / 12
WWW.ALL-TRANS.BY

„ Shackle T10059

„ Workshop crane VAS 6100

- Fasten engine sling 2024 A with shackle T10059 to

ProCarManuals.com

shop crane VAS 6100 , as shown in the illustration.

Input shaft side:

1. Hole for hook in position 1 of engine sling .

Output shaft side:

1. Hole for hook in position 8 of engine sling .

Shackle:

In position 3, input shaft side, of engine sling .

Caution!

The hooks and locating pins must be secured with

locking pins.
 ATF level, checking and topping off Page 1 / 5
WWW.ALL-TRANS.BY

37 - 4

ATF level, checking and topping off

ATF level, checking

Warning!

Wear eye protection.

ProCarManuals.com

Special tools, testers and auxiliary items

required

„ Drip tray V.A.G 1306

„ Torque wrench V.A.G 1331

„ Torque wrench V.A.G 1332

„ ATF filler tool V.A.G 1924 To

 ATF level, checking and topping off Page 2 / 5
WWW.ALL-TRANS.BY

check ATF level, older ATF filler

tools must be modified. The filling
hook must be shortened in width to
20 mm. This is the only way
possible to insert it into the ATF
check hole. Deburr and clean the
hook after cutting it.

„ Vehicle diagnostic, testing, and

information system VAS 5051

„ Diagnostic cable, 3 m with voltage

supply VAS 5051/1 or Diagnostic
cable, 5 m without voltage supply
VAS 5051/3
ProCarManuals.com

Description

The test is performed according to the overflow principle

depending on ATF temperature.

If during a repair, the ATF circulation to the cooler was

opened, this inspection must be performed twice.
Important: After the first inspection the ATF must be heated
to at least 100 C - Test drive with measuring device!
After the ATF cools off again, inspect the ATF level again
as described here.

- Use the following illustration Topic 37-4 to ascertain

which is the ATF check plug.

The ATF level will vary according to temperature of the

ATF.

Checking ATF level at too low ATF temperature leads to

overfilling.

Performing ATF level check when ATF temperature is too

high will cause insufficient filling.

Warning!

If the ATF level is too high or too low it will adversely

affect the operation of the transmission.
 ATF level, checking and topping off Page 3 / 5
WWW.ALL-TRANS.BY

ATF check plug - arrow -

- ATF fill level is affected by ATF temperature.

ATF level, checking

Test requirements:
ProCarManuals.com

„ Transmission not in emergency running mode, ATF

temperature not above approx. 30 C.

„ Vehicle is level

„ Selector level at "P"

At start of test, ATF temperature must not be more than 30

C.

- Secure container of ATF filler tool V.A.G 1924 to

vehicle.

- Connect VAS 5051 and advance program until

"Function/component selection" is displayed 37-1,
Tester , connecting .

- Then press "Powertrain (Repair Group 01; 10 to 26; 28 to

 ATF level, checking and topping off Page 4 / 5
WWW.ALL-TRANS.BY

39)" .

- Then "Automatic transmission 09D" .

- Press "Functions" .

- Press "Check ATF level" .

- Press .

- Start engine.

- Depress brake.

- Shift selector level into each position for at least 2

seconds. Then, place selector lever in position "P" .

- Raise vehicle.

- Place appropriate receptacle underneath transmission.

- Press .
ProCarManuals.com

- Remove sealing plug in oil pan - arrow - to check ATF.

At

Test temperature: 35 C to 45 C

The ATF level - arrow - is OK, if ATF drips steadily.

 ATF level, checking and topping off Page 5 / 5
WWW.ALL-TRANS.BY

Only a small amount of ATF should come out of the

inspection hole when engine is running.

- Tighten ATF inspection plug to 70 Nm. The ATF test

ends.

- Switch off engine.

If during a repair, the ATF circulation to the cooler was

opened, this inspection must be performed twice.
Important: After the first inspection the ATF must be heated
to at least 100 C - Test drive with measuring device!
After the ATF cools off again, inspect the ATF level again
as described here.
ProCarManuals.com
 ATF lines and ATF cooler Page 1 / 9
WWW.ALL-TRANS.BY

37 - 5

ATF lines and ATF cooler

„ Assembly overview, vehicles with V6 gasoline
engine a 37-5, ATF lines (vehicles with V6
gasoline engine), assembly overview

„ Assembly overview, vehicles with V8 gasoline and

V10 diesel engine 37-5, ATF lines (vehicles with
V8 and V10 diesel engine), assembly overview

ATF lines (vehicles with V6 gasoline engine), assembly

overview
ProCarManuals.com

1 - Bolt, 25 Nm

„ Before tightening bolt, push in line

onto stop by hand
 ATF lines and ATF cooler Page 2 / 9
WWW.ALL-TRANS.BY

2 - Bolt, 10 Nm

3 - Bolt, 10 Nm

4 - Bolt, 10 Nm

„ Before tightening bolt, push in line

onto stop by hand

5 - Thermostat

a - ATF line

„ Moisten O-rings with ATF

b - ATF line

„ Moisten O-rings with ATF

ATF lines (vehicles with V8 and V10 diesel engine),

assembly overview
ProCarManuals.com
 ATF lines and ATF cooler Page 3 / 9
WWW.ALL-TRANS.BY

1 - Bolt, 25 Nm

„ Before tightening bolt, push in line

onto stop by hand

2 - Bolt, 8 Nm

3 - Bolt, 8 Nm

4 - Bolt, 10 Nm

„ Before tightening bolt, push in line

onto stop by hand

5 - Thermostat

a - ATF line

„ Moisten O-rings with ATF

b - ATF line

Moisten O-rings with ATF

ProCarManuals.com

ATF lines and ATF cooler, removing and installing

Removing

Overview of cooler

1 - Cooler for coolant

2 - Retaining clamps
3 - Condenser
 ATF lines and ATF cooler Page 4 / 9
WWW.ALL-TRANS.BY

4 - ATF cooler
5 - Cooler for power steering
6 - Lock carrier

- Remove noise insulation under engine

Repair Manual, Body Exterior, Repair Group 50,

- Remove front bumper

Repair Manual, Body Exterior, Repair Group 63,

.
ProCarManuals.com

- Bring lock carrier into service position

Repair Manual, Body Exterior, Repair Group 50,

- Remove bolt - 1 - and pull ATF lines out from thermostat

- 2- .

- Plug ATF lines and thermostat with clean plugs.

- Remove front ATF lines to ATF cooler at thermostat - 2 -

. For this, counterhold at thermostat.

- Plug ATF lines and thermostat with clean plugs.

 ATF lines and ATF cooler Page 5 / 9
WWW.ALL-TRANS.BY

- Loosen clamps - arrow - for condenser - 1 - and ATF

cooler - 2 - .

- Remove ATF cooler with lines.

- Remove ATF lines at ATF cooler. For this, counterhold at

ATF cooler.

- Plug ATF lines and ATF cooler with clean plugs.

ProCarManuals.com

- Remove bolt for ATF line retainer on right of engine.

- Remove bolt for ATF line retainer on transmission.

- Remove ATF lines from transmission.

- Plug ATF lines and transmission with clean plugs.

 ATF lines and ATF cooler Page 6 / 9
WWW.ALL-TRANS.BY

Installing

Installation is in reverse order of removal. Note the

following:

- Moisten O-rings with ATF.

ProCarManuals.com

- Remove plugs and insert ATF lines into transmission up

to limit stop.

- Fasten bolt

- Fasten bolt for ATF line retainer on transmission.

- Fasten bolt for ATF line retainer on right of engine.

- Remove plugs and fasten ATF lines at ATF cooler and

thermostat.
 ATF lines and ATF cooler Page 7 / 9
WWW.ALL-TRANS.BY

- Install condenser - 1 - and ATF cooler - 2 - .

- Install clamps - arrow - .

ProCarManuals.com

- Remove plugs, insert ATF lines completely into

thermostat - 2 - and fasten bolt - 1 - .

- Automatic transmission fluid (ATF) level, checking and

topping off 37-4, ATF level, checking .

- Check connections of ATF lines for leaks while checking

ATF level.

- Install lock carrier

Repair Manual, Body Exterior, Repair Group 50,

- Install front bumper

Repair Manual, Body Exterior, Repair Group 63,

.
 ATF lines and ATF cooler Page 8 / 9
WWW.ALL-TRANS.BY

- Install noise insulation under engine

Repair Manual, Body Exterior, Repair Group 50,

ATF lines and ATF cooler, cleaning

If the ATF is dirty or a replacement transmission is being

installed, blow through the ATF cooler and ATF lines with
compressed air (max. 10 bar).

Warning!

Wear eye protection.

- Thoroughly clean area surrounding connections at ATF

line/transmission, ATF line/thermostat and ATF line/ATF
ProCarManuals.com

cooler.

- Remove bolt - 1 - and remove ATF lines from thermostat

- 2- .

- Remove front ATF lines to ATF cooler at thermostat - 2 -

. For this, counterhold at thermostat.

- Remove and empty ATF cooler 37-5, ATF lines and

ATF cooler, removing and installing .
 ATF lines and ATF cooler Page 9 / 9
WWW.ALL-TRANS.BY

- Remove ATF lines from transmission.

- Place a hose on an ATF line for transmission/thermostat

and secure it with a hose clamp. Place the other end of the
hose into an appropriate container.

- Blow through ATF line with compressed air.

- Change hose over to other ATF line and repeat

sequence.
ProCarManuals.com

- Moisten O-rings with ATF.

- ATF lines and ATF cooler, installing 37-5, ATF lines

and ATF cooler, removing and installing .
 Transmission Control Module (TCM) J217 Page 1 / 4
WWW.ALL-TRANS.BY

37 - 6

Transmission Control Module (TCM) J217

Transmission control module (TCM) J217 , removing and
installing

Special tools, testers and auxiliary items required

ProCarManuals.com

„ Torque wrench V.A.G 1331

„ Vehicle diagnostic, testing, and information system

VAS 5051

Removing

- Before removing transmission control module (TCM)

J217 , the control module identification as well as the
coding must be queried from the control module.

Note:

„ To prevent damage to the front trim under the right

front seat, the retaining tabs on the trim are
displayed in the following illustration.
 Transmission Control Module (TCM) J217 Page 2 / 4
WWW.ALL-TRANS.BY

„ The retaining tabs - A - grab behind a cross

member under the seat. The trim must be pushed
down and back at the same time. Hold the trim in
this position and pull upward in the area of the
retaining tabs - A - to release them.

„ The retaining tabs - B - grab in the recesses of the

cross member in front of the seat. These are
ProCarManuals.com

released by pushing down and pulling forward.

„ The retaining tabs - C - are clipped into the side trim

of the seat and are released by pulling forward.

- Move seat to the most rear and upward position.

- Release retaining tabs "A" - arrows A - by pressing

down and pushing rearward at the same time. In this
position, lift the trim in the area of the retaining tabs "A" -
arrows A - .

- Press trim down and pull forward at the same time.

Thereby the retaining tabs "B" - arrows B - and "C" -
arrows C - are released.

- Move seat to the most front and upward position.

 Transmission Control Module (TCM) J217 Page 3 / 4
WWW.ALL-TRANS.BY

- The procedure for disconnecting batteries must

absolutely be obeyed.

- Disconnect battery Ground (GND) strap with ignition

switched off

Repair Manual, Electrical Equipment, Repair Group 27,

.
ProCarManuals.com

Located in housing - 1 - is transmission control module

J217 and the differential control module J646 .

- Release and pull off connectors from differential control

module J646 - 2 - and transmission control module J217 -
3- .

- Remove bolt - arrow - and remove housing with control

modules from mounting.
 Transmission Control Module (TCM) J217 Page 4 / 4
WWW.ALL-TRANS.BY

- Pull retaining tabs outward - arrows 1 - and pull control

module out from housing - arrow 2 - .

Installing

Installation is in reverse order of removal. Note the

following:

- Verify the previous coding, and code new control

ProCarManuals.com

module.

- Install seat trim

Repair Manual, Body Interior, Repair Group 72,

- Observe work sequence after connecting the battery

Repair Manual, Electrical Equipment, Repair Group 27,

.
 Seals, replacing Page 1 / 4
WWW.ALL-TRANS.BY

37 - 7

Seals, replacing
Output shaft seal, replacing
ProCarManuals.com

Special tools, testers and auxiliary items

required

„ Puller T10055

„ Adapter T10055/2

„ Press Tool For Shaft Seal

T10180

„ Thrust piece T10186

 Seals, replacing Page 2 / 4
WWW.ALL-TRANS.BY

Removing

- Remove transfer case 37-3, Transmission, removing

and installing .

- To pull out seal, install a sheet metal screw of approx. 4

ProCarManuals.com

mm diameter into seal - arrow - .

„ Install sheet metal screw in so that it jams between

seal and metal ring.

„ Do not screw in sheet metal screw too far to avoid

damaging bearing behind it.

- Pull out seal with puller T10055 .

Installing

- The new seal must be coated with ATF, especially at the

sealing lips.
 Seals, replacing Page 3 / 4
WWW.ALL-TRANS.BY

- First place Press Tool For Shaft Seal T10180 onto

output shaft, so that the seal cannot be damaged.
ProCarManuals.com

- Then, drive in the new seal up to the limit stop using

Press Tool For Shaft Seal T10180 . When doing this, do
not cant sealing ring.

- Then check ATF level and top off 37-4, ATF level,
checking and topping off .

Selector shaft seals, replacing

Special tools, testers and auxiliary items required

„ Thrust piece T10174

„ Scriber

- Be careful when using scriber to removing seals.

 Seals, replacing Page 4 / 4
WWW.ALL-TRANS.BY

- Apply ATF to circumference and space between sealing

lips of the new seal.

Installation position:

The open side of the sealing ring faces transmission.

- Drive in new seals using thrust piece T10174 , thereby

not distorting the seal.

- Multi-function transmission range (TR) switch, installing

and adjusting 38-5, Multi-Function Transmission Range
(TR) Switch F125 , removing, installing and adjusting .
ProCarManuals.com
 Oil pan, removing and installing Page 1 / 3
WWW.ALL-TRANS.BY

38 - 1

Oil pan, removing and installing

Special tools, testers and auxiliary items required
ProCarManuals.com

„ Drip tray V.A.G 1306

„ Torque wrench V.A.G 1331

Removing

- Remove noise insulation for transmission.

- Place drip tray V.A.G 1306 underneath.

 Oil pan, removing and installing Page 2 / 3
WWW.ALL-TRANS.BY

- Remove oil drain plug - 1 - .

- Drain ATF.

- Loosen oil pan bolts - 1 - in a diagonal pattern and

remove oil pan.

Installing
ProCarManuals.com

- Clean all magnets in depressions of the oil pan. Ensure

that the magnets are in full contact with the oil pan.

- Install oil pan with a new gasket - 1 - .

- Make sure that all spacer sleeves - 2 - are located

completely in the new gasket - 1 - .

- Tighten oil pan bolts in diagonal sequence and in stages

38-1, Torque specifications .

Replace drain plug seal.

- Tighten oil drain plug 38-1, Torque specifications .

- After installation, fill with ATF, check ATF level, and top
off 37-4, ATF level, checking .

Torque specifications
 Oil pan, removing and installing Page 3 / 3
WWW.ALL-TRANS.BY

Drain plug 28 Nm
Oil pan bolts 8 Nm
ProCarManuals.com
 ATF strainer, removing and installing Page 1 / 2
WWW.ALL-TRANS.BY

38 - 2

ATF strainer, removing and installing

Special tools, testers and auxiliary items required
ProCarManuals.com

„ Torque wrench V.A.G 1410

„ 3 threaded studs M6 x 70 (self-fabrication)

Removing

- Remove oil pan 38-1, Oil pan, removing and

installing .

- Remove bolts - arrows - .

- Pull off oil strainer.

Installing
 ATF strainer, removing and installing Page 2 / 2
WWW.ALL-TRANS.BY

- Push new gasket - 1 - onto intake flange of oil strainer -

2 - and wet with ATF.
ProCarManuals.com

The threaded studs M6 x 70 - arrows - are needed to

guide oil strainer.

- Install 3 threaded studs M6 x 70 into valve body by

hand.

- Place oil strainer onto threaded studs .

- Carefully press suction collar into opening at valve body

up to stop.

- Fasten bolts - arrows - for oil strainer 38-2, Torque

specifications .

- Install oil pan 38-1, Oil pan, removing and installing .

- After installation, fill with ATF, check ATF level, and top
off 37-4, ATF level, checking .

Torque specifications

Oil strainer bolts 10 Nm

 Automatic Transmission Hydraulic Pressure Sensor 1 G193 and Automatic Transmissi... Page 1 / 2

Volkswagen Technical Site: http://volkswagen.msk.ru http://vwts.info http://vwts.ru

огромный архив документации по автомобилям Volkswagen, Skoda, Seat, Audi
WWW.ALL-TRANS.BY

Automatic Transmission Hydraulic Pressure Sensor

1 G193 and Automatic Transmission Hydraulic
Pressure Sensor 2 G194 , removing and installing
Senders must always be replaced together.

Special tools, testers and auxiliary items required

ProCarManuals.com

„ Torque wrench V.A.G 1410

Removing

- If still installed, remove oil pan 38-1, Oil pan, removing

and installing and oil strainer 38-2, ATF strainer,
removing and installing .

- Carefully pull off connectors for Automatic Transmission

Hydraulic Pressure Sensor 1 G193 - 1 - and Automatic
Transmission Hydraulic Pressure Sensor 2 G194 - 2 - .

- Remove both sensors.

Installing

Sensors must always be replaced together.

 Automatic Transmission Hydraulic Pressure Sensor 1 G193 and Automatic Transmissi... Page 2 / 2
WWW.ALL-TRANS.BY

- Install 2 new sensors and fasten to 5 Nm.

- Push connectors onto sensors - 1 - and - 2 - up to

stop.

The connectors must engage.

- Install oil strainer 38-2, ATF strainer, removing and

installing and oil pan 38-1, Oil pan, removing and
installing .
ProCarManuals.com

- After installation, fill with ATF, check ATF level, and top
off 37-4, ATF level, checking .
 Valve body, overview Page 1 / 4
WWW.ALL-TRANS.BY

38 - 4

Valve body, overview

The valve body and/or the lines can be removed and
installed with transmission either removed or
installed.
ProCarManuals.com

„ Solenoid Valve 2 N89

„ Connector for Transmission

Output Speed (RPM) Sensor
G195

„ The sensor is located behind

valve body

„ Automatic Transmission
Hydraulic Pressure Sensor 2
G194
 Valve body, overview Page 2 / 4
WWW.ALL-TRANS.BY

„ Removing and installing

38-3, Automatic
Transmission Hydraulic
Pressure Sensor 1 G193
and Automatic Transmission
Hydraulic Pressure Sensor 2
G194 , removing and
installing

„ Automatic Transmission
Hydraulic Pressure Sensor 1
G193

„ Removing and installing

38-3, Automatic
Transmission Hydraulic
Pressure Sensor 1 G193
and Automatic Transmission
Hydraulic Pressure Sensor 2
G194 , removing and
ProCarManuals.com

installing

„ Solenoid Valve 4 N91

„ Transmission Input Speed (RPM)

Sensor G182

„ Transmission Fluid Temperature

Sensor G93

„ Solenoid Valve 6 N93

„ Solenoid Valve 3 N90

„ Solenoid Valve 5 N92

„ Solenoid Valve 10 N283

„ Solenoid Valve 1 N88

More information on component functions and

troubleshooting component failures can be found in
Self-study program no. 89K303 6 Spd. Automatic
Transmission 09D All Wheel Drive .

Valve body, removing and installing

- If still installed, remove oil pan 38-1, Oil pan, removing

and installing and oil strainer 38-2, ATF strainer,
removing and installing .
 Valve body, overview Page 3 / 4
WWW.ALL-TRANS.BY

- Carefully disconnect connectors for Automatic

Transmission Hydraulic Pressure Sensor 1 G193 - 1 - and
Automatic Transmission Hydraulic Pressure Sensor 2
G194 - 2 - .
ProCarManuals.com

- Disconnect connector - arrow - .

- Carefully release connector and pull off.

 Valve body, overview Page 4 / 4
WWW.ALL-TRANS.BY

- The Transmission Fluid Temperature Sensor G93 must

be tightened to 10 Nm.
ProCarManuals.com

- Remove valve body bolts in diagonal sequence.

Tightening torque: 8 Nm plus an additional 90 .

- The Transmission Output Speed (RPM) Sensor G195

must be tightened to 10 Nm.

- Installation is in reverse order of removal.

- After installation, fill with ATF, check ATF level, and top
off 37-4, ATF level, checking .
 Multi-Function Transmission Range (TR) Switch F125 , removing, installing and adjus... Page 1 / 4
WWW.ALL-TRANS.BY

38 - 5

Multi-Function Transmission Range (TR) Switch

F125 , removing, installing and adjusting
Special tools, testers and auxiliary items required
ProCarManuals.com

„ Setting Gauge T10173

„ Torque wrench V.A.G 1331

Removing

For reasons of clarity, the transmission is shown removed

throughout this procedure.

- Place selector lever in position "P" .

 Multi-Function Transmission Range (TR) Switch F125 , removing, installing and adjus... Page 2 / 4
WWW.ALL-TRANS.BY
ProCarManuals.com

- Remove cap nut - 4 - .

- Remove cover - 3 - from selector shaft.

- Carefully bend back hooks of lock washer - 1 - using a

screwdriver.

If one hook breaks off, the washer must be replaced.

- Remove nut - 2 - and lock washer - 1 - from selector

shaft.

- Disconnect connector from Multi-Function Transmission

Range (TR) Switch F125 .

- Remove bolts - arrows B - and remove multi-function

transmission range switch - arrow A - from selector
shaft.

Installing and adjusting

- Move selector shaft lever to position "N" on

transmission.

- Connect Multi-Function Transmission Range (TR) Switch

F125 to shift rod.
 Multi-Function Transmission Range (TR) Switch F125 , removing, installing and adjus... Page 3 / 4
WWW.ALL-TRANS.BY

- Fasten bolts - arrows B - hand tight for multi-function

transmission range (TR) switch F125 .
ProCarManuals.com

- Place setting gauge T10173 onto selector shaft.

- Unhook selector lever cable.

- Turn multi-function transmission range (TR) switch - A -

so far until tab on connector - arrow 1 - engages the
groove of setting gauge T10173 .
 Multi-Function Transmission Range (TR) Switch F125 , removing, installing and adjus... Page 4 / 4
WWW.ALL-TRANS.BY

- Fasten bolts - arrows - for multi-function transmission

range (TR) switch F125 to 6 Nm.
ProCarManuals.com

- Remove setting gauge T10173 from selector shaft.

- Hook selector lever cable in.

Further installation is in reverse order of removal.

- Check adjustment of selector lever cable 37-2,

Selector lever cable, checking and adjusting .