Scribd
Upload
238 views2 pages

Menú IVR ATA 187

This document provides instructions for accessing the Interactive Voice Response (IVR) on a Cisco ATA 187 Analog Telephone Adaptor and configuring phone settings through voice prompts. It details the steps to access the IVR by going off-hook and pressing the setup button before entering a PIN number. A table lists the various configuration options in the IVR menu that can be selected by pressing numbers on the phone keypad, such as reviewing and setting network settings and enabling or disabling DHCP. The reset option will restore all settings to factory defaults.

Uploaded by

Guillermo Bejarano
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
238 views2 pages

Menú IVR ATA 187

This document provides instructions for accessing the Interactive Voice Response (IVR) on a Cisco ATA 187 Analog Telephone Adaptor and configuring phone settings through voice prompts. It details the steps to access the IVR by going off-hook and pressing the setup button before entering a PIN number. A table lists the various configuration options in the IVR menu that can be selected by pressing numbers on the phone keypad, such as reviewing and setting network settings and enabling or disabling DHCP. The reset option will restore all settings to factory defaults.

Uploaded by

Guillermo Bejarano
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

CH A P T E R 8

Voice Menu Codes

This section contains information on accessing the Interactive Voice Response (IVR) and a
quick-reference list of the voice configuration menu options for the ATA 187.

Accessing the IVR and Configuring Your Phone Setting


To access the IVR and configure your phone settings, follow these steps:

Note You can change the PIN on the Cisco Unified CM User Options web page.

Procedure

Step 1 To access the IVR, go off-hook on the phone connected to Line 1 and press the Set Up button on the
front panel of the ATA 187.
The IVR prompts for a password.

Note The ATA 187 allows you to enter only numerical values for password.

Step 2 Enter the PIN by pressing the number keypad, followed by # button.
You are at the IVR main configuration menu.
Step 3 Follow the voice prompts on the IVR. See Table 8-1 for information on navigating the IVR.
Step 4 To return to the main configuration menu, press #.
Step 5 To exit the IVR, end the call.

Cisco ATA 187 Analog Telephone Adaptor Administration Guide for SIP (Version 1.0)
OL-21862-01 8-1
Chapter 8 Voice Menu Codes

Table 8-1 describes the various options in the IVR Configuration Menu

Table 8-1 Navigating the IVR Configuration Menu

Action IVR Code Navigating Notes


Review or Set Network Settings 1 If DHCP is enabled, the IVR announces each
network parameter.
If DHCP is disabled, the IVR announces each
network parameter, pausing in between to allow
you to enter a new value.
1. IVR announces the IP Address. To change
the IP address for the phone, use the keypad
to enter a new IP address, followed by the #.
To retain the current IP address, press #.
2. IVR announces the subnet mask. To change
the subnet mask use the keypad to enter a
new IP address, followed by the #. To retain
the current subnet mask, press #.

Note To enter the dot “.” that separates each


octet in the IP address, press *.

3. IVR announces the default gateway. To


change the default gateway, use the keypad to
enter a new IP address, followed by the #. To
retain the current default gateway, press #.
Review or Set TFTP Server 2 IVR announces the current TFTP setting.
To change the TFTP server, use the keypad to
enter a new IP address, followed by the #. To
retain the current TFTP server, press #.
To reset a TFTP server back to the TFTP server
set by the DHCP server from a manually
configured TFTP server, press *.
Note To enter the dot “.” that separates each
octet in the IP address, press *.
Enable or Disable DHCP 3 Press 3 to toggle DHCP to enable or disable.
Review or Set the VLAN ID 4 Press 4 to review and set the Administrator
VLAN ID.
Reset to factory settings 0 —
Note All configuration settings will reset to
default factory settings, the and phone
will reset. It will take some time for the
phone to re-register. Select this option
only when needed.

Cisco ATA 187 Analog Telephone Adaptor Administration Guide for SIP (Version 1.0)
8-2 OL-21862-01

You might also like