 KIRCHHOFF'S CIRCUIT LAWS  Integrated reverse polarity protection

ME1.1.1 DC TECHNOLOGY I  ANALYSIS OF RESISTIVE CIRCUITS due to connection to the Master Unit
 The use of safety cables avoids
unintentional short-circuiting
SERIES CIRCUITS – PARALLEL
CIRCUITS, UNLOADED/LOADED
THE COM4LAB COURSE ENTITLED “DC VOLTAGE DIVIDERS – WHEATSTONE
TECHNOLOGY I” IS THE FIRST COURSE ON BRIDGE
THE FUNDAMENTALS OF DC TECHNOLOGY.
THE FUNDAMENTAL CONCEPTS AND LAWS
OF ELECTRICAL ENGINEERING ARE Technical Data:
EXPLAINED AND PRACTICALLY DEVISED PREVIOUS
USING A NUMBER OF EXPERIMENTS. THE
COURSE COMPRISES 14 CHAPTERS. KNOWLEDGE
70011-20 COM4LAB Course: DC
TOTAL DURATION: UP TO 5 HOURS Technology I
THE STUDENTS DO NOT NEED ANY
PREVIOUS KNOWLEDGE OF ELECTRICAL
ENGINEERING IN ORDER TO BE ABLE TO
TARGET AUDIENCE COMPLETE THE COURSE SUCCESSFULLY.
DEALING WITH SIMPLE FORMULAS IS,
HOWEVER, REQUIRED.
AMONG OTHERS, THE COURSE CAN BE
USED TO SUPPORT THE TRAINING PROCESS
FOR THE FOLLOWING PROFESSIONS:

 ELECTRICAL SYSTEM FITTER 70011-00 COM4LAB Board: DC

 ELECTRONICS TECHNICIAN FOR Technology I
AUTOMATION TECHNOLOGY
 ELECTRONICS TECHNICIAN FOR
ENERGY AND BUILDING TECHNOLOGY
 ELECTRONICS TECHNICIAN FOR
DEVICES AND SYSTEMS
 ELECTRONICS TECHNICIAN FOR The COM4LAB course DC Technology I
INFORMATION AND SYSTEM is the first course on the fundamentals of
TECHNOLOGY DC technology. The fundamental
concepts and laws of electrical
 ELECTRONICS TECHNICIAN FOR
engineering are explained and
MACHINE AND DRIVE TECHNOLOGY
developed in a practical environment
 AIRCRAFT ELECTRONICS TECHNICIAN using a raft of tests. The course
 INFORMATION ELECTRONICS comprises 14 chapters.
TECHNICIAN
 SYSTEM ELECTRONICS TECHNICIAN The course covers the following topics:

LEARNING The experiment board to the COM4LAB

course DC Technology I (supplied
 (simple) electrical circuit with
switch(es)
separately).
OBJECTIVES series circuit – parallel circuit –
There are 13 experiment panels on the multiway switching – polarity
THE STUDENTS ARE TO: experiment board. Each experiment reversing circuit – relay
panel contains a self-contained circuit
that is put into operation and examined
 BE ABLE TO UNDERSTAND THE SETUP depending on the selected experiment.  conductivity and electrical resistance
AND EFFECT OF BASIC CIRCUITS AND The active experiment panel is indicated  Ohm’s law
 BE ABLE TO UNDERSTAND AND APPLY by a lit green LED.  Kirchhoff's circuit laws
THE FUNDAMENTAL LAWS OF
ELECTRICAL ENGINEERING.
 analysis of resistive circuits
The experiment board, housed within a
sturdy board carrier, is to be used in
conjunction with, and powered by the series circuits – parallel circuits,
TOPICS Master Unit (supplied separately).
Circuits are wired by using 2 mm safety
unloaded/loaded voltage dividers –
Wheatstone bridge
cables (supplied separately).
THE COURSE COVERS THE FOLLOWING The course …
TOPICS:
Dimensions
 can be displayed and filled out on
 (SIMPLE) ELECTRICAL CIRCUIT WITH your own tablet/smartphone/laptop.
SWITCH(ES)
 Circuit board: 280 × 200 mm2
 Frame: 296,5 × 354 mm2  is platform-independent - a current
browser is sufficient.
SERIES CIRCUIT – PARALLEL CIRCUIT –  can be distributed to students via QR
MULTIWAY SWITCHING – POLARITY Supply voltage codes.
REVERSING CIRCUIT – RELAY
 enables interactive experimenting:
 +15 V DC and +5 V DC from the The measured values from the
 CONDUCTIVITY AND ELECTRICAL Master Unit via corresponding relays Master Unit are automatically made
RESISTANCE available for evaluation in tables and
diagrams. The analysis and
 OHM'S LAW Protective functions
LD Didactic GmbH Technical Documentation Page 1
 documentation of the experiment on Frequency range: 0.5 Hz – 100 kHz, COM4LAB Master Unit. An additional
the student device can be done at also DC USB-A port with fast charge ensures
school or at home. SYNC output: TTL clock parallel charging of one mobile device.
 can be edited and thus adapted to frequency 0.5 Hz – 100 kHz
your own lesson plan. Output voltage: max. ±10 V, (0 – 20
Technical data
V)
Output current: max. ±250 mA
Perpetual course license.
 Digital 4-channel oscilloscope:  45 W PD, 15 V/3 A
4 differential inputs  USB-A Port DC 5 V/2,4 A
Technical data Sampling rate: 1 MS/s per channel
Bandwidth: 200 kHz  Overvoltage protection
Memory depth: 1KS per channel  Overheat protection
 Product key for activation of the Resolution: 12 Bit per channel
course licence via Time ranges from 10 μs/div to 500
https://register.leylab.de is Scope of delivery
ms/div
necessary. Later on the course can Voltage ranges from 10 mV/div to 10
be accessed and distributed from V/div  2 m USB-C/USB-C cable
LeyLab. Trigger CH1 - CH4 and EXT
 System requirements: (referenced to ground), in 4095
- PC, tablet or smartphone with a steps, rising/falling edge
current browser  Digital analyzer: ALTERNATIVELY USB-C CHARGER
- internet access 8+1 digital signal inputs WITH UK-PLUG OR US-PLUG
Input voltage TTL-compatible
Sampling frequency: 200 Hz – 2
MHz 70000-22 COM4LAB Set of Safety
Memory depth: 9 Bit x 2 K Leads, 2 mm, 24 pcs
Triggering on any combination of the
Technical Data: input states

Additional properties
70000-00 COM4LAB Master Unit
 Voltage supply:
15 V/3 A
USB-C
 Interfaces:
WLAN
Ethernet 100 MBits RJ45
USB
 Extensions: Set of highly fexible test leads with
Extension Slot insulation in PVC with assembled
USB Interface (type A) stackable 2 mm multilam plugs with rigid
The COM4LAB Master Unit is a  NFC insulating sleeve on both ends.
multifunctional, compact, measuring  Light strip & LEDs for status display
interface. As a universal base station it is  Security lock for mechanical  6 x 150 mm, red
used for the operation and power supply attachment and electronic activation
for the COM4LAB experiment boards of the experiment boards
 6 x 150 mm, black
and as an independent measuring  2 x 150 mm, blue
laboratory. The Master Unit can be
 Anti-theft protection (port for
Kensington lock)  4 x 300 mm, red
simultaneously connected to up to four
digital terminal devices (PC, tablet or
 4 x 300 mm, black
smartphone) for the recording of Scope of delivery  2 x 300 mm, blue
measurements and for remote control of
its built-in functions. The Master Unit can Technical data
be quickly attached to an experiment  USB cable
board. Its clear and structured design  NFC card
results in easy operation.  Rated voltage/current 600 V, CAT II /
10 A
Dimensions  Lead cross section 0,5 mm²
ACCESSORIES
 295 x 154 × 30 mm3
70000-11 USB-C Charger 45 W ADDITIONALLY REQUIRED
Integrated measuring instruments
Europlug (Type C)
PC, TABLET OR SMARTPHONE WITH A
 Two digital multimeters: CURRENT BROWSER
Voltage: DC/AC – 2 V | 20 V
Current: DC/AC – 20 mA | 200 mA |
2A ME1.1.2 DC TECHNOLOGY II
Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2
MΩ
Autoranging for all measurement
ranges THE COM4LAB COURSE ENTITLED “DC
TECHNOLOGY II” IS THE SECOND COURSE
 Digital Function Generator:
ON THE FUNDAMENTALS OF DC
digitally generated sinusoidal,
USB-C Charger with a 45 W quick TECHNOLOGY. CHARACTERISTICS OF
triangular, square-wave signal types,
charge function as a power supply for the VARIOUS PASSIVE ELECTRICAL
also DC
LD Didactic GmbH Technical Documentation Page 2
 COMPONENTS ARE RECORDED AND THE  BATTERY  The use of safety cables avoids
BASIC CIRCUIT TYPES IN ELECTRICAL unintentional short-circuiting
ENGINEERING ARE PRACTICALLY DEVISED
USING A NUMBER OF EXPERIMENTS. THE SERIES CIRCUIT – PARALLEL CIRCUIT
COURSE COMPRISES 15 CHAPTERS.

TOTAL DURATION: MORE THAN 5 HOURS PREVIOUS Technical Data:

KNOWLEDGE
TARGET AUDIENCE
THE STUDENTS DO NOT NEED ANY 70012-20 COM4LAB Course: DC
PREVIOUS KNOWLEDGE OF ELECTRICAL
AMONG OTHERS, THE COURSE CAN BE Technology II
ENGINEERING IN ORDER TO BE ABLE TO
USED TO SUPPORT THE TRAINING PROCESS
COMPLETE THE COURSE SUCCESSFULLY.
FOR THE FOLLOWING PROFESSIONS:
DEALING WITH SIMPLE FORMULAS IS,
HOWEVER, REQUIRED.
 ELECTRICAL SYSTEM FITTER
 ELECTRONICS TECHNICIAN FOR
AUTOMATION TECHNOLOGY
 ELECTRONICS TECHNICIAN FOR
ENERGY AND BUILDING TECHNOLOGY 70012-00 COM4LAB Board: DC
 ELECTRONICS TECHNICIAN FOR
Technology II
DEVICES AND SYSTEMS
 ELECTRONICS TECHNICIAN FOR
INFORMATION AND SYSTEM
TECHNOLOGY
 ELECTRONICS TECHNICIAN FOR
MACHINE AND DRIVE TECHNOLOGY
 AIRCRAFT ELECTRONICS TECHNICIAN
The COM4LAB course DC Technology
 INFORMATION ELECTRONICS
II is the second course on the
TECHNICIAN
fundamentals of DC technology.
 SYSTEM ELECTRONICS TECHNICIAN Characteristics of various passive
electrical components are recorded and
the basic circuit types in electrical
LEARNING engineering are practically devised using
a number of experiments. The course
comprises 15 chapters.
OBJECTIVES
The experiment board to the COM4LAB The course covers the following topics:
THE STUDENTS SHOULD BE ABLE TO: course DC Technology II (supplied
separately).
 characteristics of the following
 RECORD THE CHARACTERISTICS OF passive electrical components
PASSIVE ELECTRICAL COMPONENTS
There are 11 experiment panels on the
AND
experiment board. Each experiment
panel contains a self-contained circuit incandescent light bulb – VDR –
 UNDERSTAND THE BEHAVIOUR OF
that is put into operation and examined diode – LDR – NTC – PTC
PASSIVE ELECTRICAL COMPONENTS
depending on the selected experiment.
SUCH AS CAPACITORS, COILS AND
The active experiment panel is indicated
BATTERIES.  capacitor
by a lit green LED.

series circuit – parallel circuit – RC

TOPICS The experiment board, housed within a
sturdy board carrier, is to be used in circuit
conjunction with, and powered by the
THE COURSE COVERS THE FOLLOWING Master Unit (supplied separately).
Circuits are wired by using 2 mm safety  coil
TOPICS:
cables (supplied separately).
inductance – moving coil instrument
 CHARACTERISTICS OF THE FOLLOWING Dimensions
PASSIVE ELECTRICAL COMPONENTS
 battery

INCANDESCENT LIGHT BULB – VDR –  Circuit board: 280 × 200 mm2

DIODE – LDR – NTC – PTC  Frame: 296,5 × 354 mm2 series circuit – parallel circuit

Supply voltage The course …

 CAPACITOR

SERIES CIRCUIT – PARALLEL CIRCUIT –  +15 V DC and +5 V DC from the  can be displayed and filled out on
RC CIRCUIT Master Unit via corresponding relays your own tablet/smartphone/laptop.
 is platform-independent - a current
Protective functions browser is sufficient.
 COIL
 can be distributed to students via QR
codes.
INDUCTANCE – MOVING COIL  Integrated reverse polarity protection  enables interactive experimenting:
INSTRUMENT due to connection to the Master Unit The measured values from the
LD Didactic GmbH Technical Documentation Page 3
 Master Unit are automatically made  Digital Function Generator: 70000-11 USB-C Charger 45 W
available for evaluation in tables and
diagrams. The analysis and
digitally generated sinusoidal, Europlug (Type C)
triangular, square-wave signal types,
documentation of the experiment on also DC
the student device can be done at Frequency range: 0.5 Hz – 100 kHz,
school or at home. also DC
 can be edited and thus adapted to SYNC output: TTL clock
your own lesson plan. frequency 0.5 Hz – 100 kHz
Output voltage: max. ±10 V, (0 – 20
V)
Perpetual course license.
Output current: max. ±250 mA
 Digital 4-channel oscilloscope:
Technical data 4 differential inputs
Sampling rate: 1 MS/s per channel
Bandwidth: 200 kHz USB-C Charger with a 45 W quick
 Product key for activation of the
Memory depth: 1KS per channel
course licence via charge function as a power supply for the
Resolution: 12 Bit per channel COM4LAB Master Unit. An additional
https://register.leylab.de is Time ranges from 10 μs/div to 500
necessary. Later on the course can USB-A port with fast charge ensures
ms/div parallel charging of one mobile device.
be accessed and distributed from
Voltage ranges from 10 mV/div to 10
LeyLab. V/div
 System requirements: Trigger CH1 - CH4 and EXT Technical data
- PC, tablet or smartphone with a (referenced to ground), in 4095
current browser steps, rising/falling edge
- internet access  45 W PD, 15 V/3 A
 Digital analyzer:
8+1 digital signal inputs  USB-A Port DC 5 V/2,4 A
Input voltage TTL-compatible  Overvoltage protection
Sampling frequency: 200 Hz – 2  Overheat protection
MHz
Memory depth: 9 Bit x 2 K
Technical Data: Triggering on any combination of the Scope of delivery
input states
 2 m USB-C/USB-C cable
70000-00 COM4LAB Master Unit Additional properties

 Voltage supply: ALTERNATIVELY USB-C CHARGER

15 V/3 A
USB-C WITH UK-PLUG OR US-PLUG
 Interfaces:
WLAN 70000-22 COM4LAB Set of Safety
Ethernet 100 MBits RJ45 Leads, 2 mm, 24 pcs
USB
 Extensions:
Extension Slot
The COM4LAB Master Unit is a USB Interface (type A)
multifunctional, compact, measuring  NFC
interface. As a universal base station it is  Light strip & LEDs for status display
used for the operation and power supply
for the COM4LAB experiment boards
 Security lock for mechanical
attachment and electronic activation
and as an independent measuring
of the experiment boards
laboratory. The Master Unit can be
simultaneously connected to up to four  Anti-theft protection (port for
digital terminal devices (PC, tablet or Kensington lock)
smartphone) for the recording of
measurements and for remote control of Scope of delivery Set of highly fexible test leads with
its built-in functions. The Master Unit can insulation in PVC with assembled
be quickly attached to an experiment stackable 2 mm multilam plugs with rigid
board. Its clear and structured design  USB cable insulating sleeve on both ends.
results in easy operation.  NFC card

Dimensions  6 x 150 mm, red

 6 x 150 mm, black
ACCESSORIES  2 x 150 mm, blue
 295 x 154 × 30 mm3
 4 x 300 mm, red

Integrated measuring instruments

 4 x 300 mm, black
 2 x 300 mm, blue

 Two digital multimeters:

Technical data
Voltage: DC/AC – 2 V | 20 V
Current: DC/AC – 20 mA | 200 mA |
2A  Rated voltage/current 600 V, CAT II /
Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2 10 A
MΩ
Autoranging for all measurement  Lead cross section 0,5 mm²
ranges

LD Didactic GmbH Technical Documentation Page 4

ADDITIONALLY REQUIRED  GENERATION OF ALTERNATING The experiment board, housed within a
VOLTAGE sturdy board carrier, is to be used in
conjunction with, and powered by the
PC, TABLET OR SMARTPHONE WITH A Master Unit (supplied separately).
STEP VOLTAGE – CONTINUOUS Circuits are wired by using 2 mm safety
CURRENT BROWSER
ALTERNATING VOLTAGE – ELECTRONIC cables (supplied separately).
GENERATION OF ALTERNATING
ME1.2.1 AC TECHNOLOGY I VOLTAGE
Dimensions

 FUNCTION GENERATOR AND

OSCILLOSCOPE  Circuit board: 280 × 200 mm2
THE COM4LAB COURSE ENTITLED “AC
TECHNOLOGY I” IS THE FIRST COURSE ON  TRANSFORMER  Frame: 296,5 × 354 mm2
THE FUNDAMENTALS OF AC TECHNOLOGY.
IT ADDRESSES THE GENERATION OF AC INDUCTION – PRINCIPLE OF THE Supply voltage
VOLTAGE, AND THE FUNCTIONS OF A
TRANSFORMER – SHORT-CIRCUITED
TRANSFORMER AND VARIOUS RECTIFIER
TRANSFORMER – LOADED
CIRCUITS ARE PRACTICALLY DEVISED USING
TRANSFORMER – TRANSFORMER
 +15 V DC, −15 V DC und +5 V DC
A NUMBER OF EXPERIMENTS. THE from the Master Unit via
LOSSES
STUDENTS ARE INSTRUCTED ON HOW TO corresponding relays
USE THE FUNCTION GENERATOR,
OSCILLOSCOPE AND MULTIMETERS. THE  RECTIFIER CIRCUITS Protective functions
COURSE COMPRISES 14 CHAPTERS.

DIODE AS A CURRENT VALVE – HALF-

TOTAL DURATION: UP TO 5 HOURS WAVE RECTIFIER M1 – FULL-WAVE
 Integrated reverse polarity protection
due to connection to the Master Unit
RECTIFIER M2 – GRAETZ BRIDGE
RECTIFIER B2 – SYMMETRICAL OUTPUT  The use of safety cables avoids
TARGET AUDIENCE VOLTAGE unintentional short-circuiting

AMONG OTHERS, THE COURSE CAN BE

USED TO SUPPORT THE TRAINING PROCESS
PREVIOUS
FOR THE FOLLOWING PROFESSIONS:
KNOWLEDGE Technical Data:
 ELECTRICAL SYSTEM FITTER
THE STUDENTS DO NOT NEED ANY
 ELECTRONICS TECHNICIAN FOR PREVIOUS KNOWLEDGE OF ELECTRICAL
AUTOMATION TECHNOLOGY ENGINEERING IN ORDER TO BE ABLE TO
70013-20 COM4LAB Course: AC
 ELECTRONICS TECHNICIAN FOR COMPLETE THE COURSE SUCCESSFULLY. Technology I
ENERGY AND BUILDING TECHNOLOGY DEALING WITH SIMPLE FORMULAS IS,
 ELECTRONICS TECHNICIAN FOR HOWEVER, REQUIRED.
DEVICES AND SYSTEMS
 ELECTRONICS TECHNICIAN FOR
INFORMATION AND SYSTEM
TECHNOLOGY
 ELECTRONICS TECHNICIAN FOR 70013-00 COM4LAB Board: AC
MACHINE AND DRIVE TECHNOLOGY Technology I
 AIRCRAFT ELECTRONICS TECHNICIAN
 INFORMATION ELECTRONICS
TECHNICIAN
 SYSTEM ELECTRONICS TECHNICIAN

LEARNING
The COM4LAB course AC Technology I
OBJECTIVES is the first course on the fundamentals of
AC technology. It addresses the
THE STUDENTS SHOULD BE ABLE TO: generation of AC voltage, and the
functions of a transformer and various
rectifier circuits are practically devised
 UNDERSTAND THE PRINCIPLE AND using a number of experiments. The
FUNCTION OF A TRANSFORMER, students are instructed on how to use the
 RECOGNISE THE EFFECTS OF VARIOUS function generator, oscilloscope and
RECTIFIER CIRCUITS AND The experiment board to the COM4LAB multimeters. The course comprises 14
course AC Technology I (supplied chapters.
 BE ABLE TO USE THE FUNCTION
separately).
GENERATOR AND THE OSCILLOSCOPE.
The course covers the following topics:
There are 11 experiment panels on the
TOPICS experiment board. Each experiment
panel contains a self-contained circuit  generation of alternating voltage
that is put into operation and examined
THE COURSE COVERS THE FOLLOWING depending on the selected experiment. step voltage – continuous alternating
TOPICS: The active experiment panel is indicated voltage – electronic generation of
by a lit green LED. alternating voltage

LD Didactic GmbH Technical Documentation Page 5

  function generator and oscilloscope used for the operation and power supply  Security lock for mechanical
for the COM4LAB experiment boards attachment and electronic activation
 transformer and as an independent measuring of the experiment boards
laboratory. The Master Unit can be
induction – principle of the simultaneously connected to up to four
 Anti-theft protection (port for
digital terminal devices (PC, tablet or Kensington lock)
transformer – short-circuited
transformer – loaded transformer – smartphone) for the recording of
transformer losses measurements and for remote control of Scope of delivery
its built-in functions. The Master Unit can
be quickly attached to an experiment
 rectifier circuits board. Its clear and structured design  USB cable
results in easy operation.  NFC card
diode as a current valve – half-wave
rectifier M1 – full-wave Dimensions
rectifier M2 – Graetz bridge
rectifier B2 – symmetrical output ACCESSORIES
voltage  295 x 154 × 30 mm3

70000-11 USB-C Charger 45 W

The course … Integrated measuring instruments
Europlug (Type C)

 can be displayed and filled out on  Two digital multimeters:

your own tablet/smartphone/laptop. Voltage: DC/AC – 2 V | 20 V
 is platform-independent - a current Current: DC/AC – 20 mA | 200 mA |
browser is sufficient. 2A
Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2
 can be distributed to students via QR MΩ
codes. Autoranging for all measurement
 enables interactive experimenting: ranges
The measured values from the  Digital Function Generator:
Master Unit are automatically made digitally generated sinusoidal,
available for evaluation in tables and triangular, square-wave signal types,
diagrams. The analysis and also DC USB-C Charger with a 45 W quick
documentation of the experiment on Frequency range: 0.5 Hz – 100 kHz, charge function as a power supply for the
the student device can be done at also DC COM4LAB Master Unit. An additional
school or at home. SYNC output: TTL clock USB-A port with fast charge ensures
 can be edited and thus adapted to frequency 0.5 Hz – 100 kHz parallel charging of one mobile device.
your own lesson plan. Output voltage: max. ±10 V, (0 – 20
V) Technical data
Output current: max. ±250 mA
Perpetual course license.
 Digital 4-channel oscilloscope:
4 differential inputs  45 W PD, 15 V/3 A
Technical data Sampling rate: 1 MS/s per channel  USB-A Port DC 5 V/2,4 A
Bandwidth: 200 kHz  Overvoltage protection
Memory depth: 1KS per channel
 Product key for activation of the
Resolution: 12 Bit per channel  Overheat protection
course licence via
Time ranges from 10 μs/div to 500
https://register.leylab.de is
ms/div Scope of delivery
necessary. Later on the course can
Voltage ranges from 10 mV/div to 10
be accessed and distributed from
V/div
LeyLab.
Trigger CH1 - CH4 and EXT  2 m USB-C/USB-C cable
 System requirements: (referenced to ground), in 4095
- PC, tablet or smartphone with a steps, rising/falling edge
current browser
- internet access
 Digital analyzer:
8+1 digital signal inputs ALTERNATIVELY USB-C CHARGER
Input voltage TTL-compatible WITH UK-PLUG OR US-PLUG
Sampling frequency: 200 Hz – 2
MHz
Memory depth: 9 Bit x 2 K 70000-22 COM4LAB Set of Safety
Technical Data: Triggering on any combination of the Leads, 2 mm, 24 pcs
input states

Additional properties
70000-00 COM4LAB Master Unit
 Voltage supply:
15 V/3 A
USB-C
 Interfaces:
WLAN
Ethernet 100 MBits RJ45
USB
 Extensions:
Extension Slot Set of highly fexible test leads with
USB Interface (type A) insulation in PVC with assembled
The COM4LAB Master Unit is a  NFC stackable 2 mm multilam plugs with rigid
multifunctional, compact, measuring insulating sleeve on both ends.
 Light strip & LEDs for status display
interface. As a universal base station it is

LD Didactic GmbH Technical Documentation Page 6

  6 x 150 mm, red THE STUDENTS SHOULD: 70014-00 COM4LAB Board: AC
 6 x 150 mm, black Technology II
 2 x 150 mm, blue  BE ABLE TO RECOGNISE THE
 4 x 300 mm, red CHARACTERISTICS AND CONNECTIONS
IN AC CURRENT CIRCUITS AND
 4 x 300 mm, black
 BE ABLE TO USE THE FUNCTION
 2 x 300 mm, blue
GENERATOR AND THE OSCILLOSCOPE.

Technical data
TOPICS
 Rated voltage/current 600 V, CAT II /
10 A THE COURSE COVERS THE FOLLOWING
 Lead cross section 0,5 mm² TOPICS:

 GENERATION OF AC VOLTAGE
ADDITIONALLY REQUIRED  CHARACTERISTIC VARIABLES IN AC
TECHNOLOGY

PC, TABLET OR SMARTPHONE WITH A  OHMIC RESISTANCE IN AN AC CIRCUIT The experiment board to the COM4LAB
 COIL IN AN AC CIRCUIT course AC Technology II (supplied
CURRENT BROWSER separately).

INDUCTIVE RESISTANCE – SERIES

ME1.2.2 AC TECHNOLOGY II CONNECTION OF RESISTOR AND COIL – There are 11 experiment panels on the
PARALLEL CONNECTION OF RESISTOR experiment board. Each experiment
AND COIL
panel contains a self-contained circuit
that is put into operation and examined
THE COM4LAB COURSE ENTITLED “AC depending on the selected experiment.
TECHNOLOGY II” IS THE SECOND COURSE  CAPACITOR IN AN AC CIRCUIT The active experiment panel is indicated
ON THE FUNDAMENTALS OF AC by a lit green LED.
TECHNOLOGY. IT ADDRESSES THE
CAPACITIVE RESISTANCE – SERIES
BEHAVIOUR OF PASSIVE COMPONENTS IN
CONNECTION OF RESISTOR AND The experiment board, housed within a
VARIOUS CIRCUITS. VARIOUS
CAPACITOR – PARALLEL CONNECTION sturdy board carrier, is to be used in
COMBINATIONS OF COIL, CAPACITOR AND
OF RESISTOR AND CAPACITOR conjunction with, and powered by the
RESISTANCE ARE ANALYSED AND
Master Unit (supplied separately).
CALCULATED. THE STUDENTS ARE
Circuits are wired by using 2 mm safety
INSTRUCTED ON HOW TO USE THE  SERIES CONNECTION OF RESISTOR, cables (supplied separately).
FUNCTION GENERATOR, OSCILLOSCOPE COIL AND CAPACITOR
AND MULTIMETERS. THE COURSE
COMPRISES 20 CHAPTERS.
 PARALLEL CONNECTION OF RESISTOR, Dimensions
COIL AND CAPACITOR
 SERIES COMPENSATION
TOTAL DURATION: UP TO 6 HOURS  Circuit board: 280 × 200 mm2
 PARALLEL COMPENSATION
 Frame: 296,5 × 354 mm2
 SERIES RESONANCE

TARGET AUDIENCE  PARALLEL RESONANCE

Supply voltage

AMONG OTHERS, THE COURSE CAN BE

USED TO SUPPORT THE TRAINING PROCESS
PREVIOUS  +15 V DC and +5 V DC from the
Master Unit via corresponding relays
FOR THE FOLLOWING PROFESSIONS:
KNOWLEDGE
Protective functions
 ELECTRICAL SYSTEM FITTER
THE STUDENTS DO NOT NEED ANY
 ELECTRONICS TECHNICIAN FOR
PREVIOUS KNOWLEDGE OF ELECTRICAL
AUTOMATION TECHNOLOGY  Integrated reverse polarity protection
ENGINEERING IN ORDER TO BE ABLE TO
due to connection to the Master Unit
 ELECTRONICS TECHNICIAN FOR COMPLETE THE COURSE SUCCESSFULLY.
ENERGY AND BUILDING TECHNOLOGY DEALING WITH SIMPLE FORMULAS IS,  The use of safety cables avoids
HOWEVER, REQUIRED. unintentional short-circuiting
 ELECTRONICS TECHNICIAN FOR
DEVICES AND SYSTEMS
 ELECTRONICS TECHNICIAN FOR
INFORMATION AND SYSTEM
TECHNOLOGY
 ELECTRONICS TECHNICIAN FOR Technical Data:
MACHINE AND DRIVE TECHNOLOGY
 AIRCRAFT ELECTRONICS TECHNICIAN
 INFORMATION ELECTRONICS
TECHNICIAN
 SYSTEM ELECTRONICS TECHNICIAN

LEARNING
OBJECTIVES

LD Didactic GmbH Technical Documentation Page 7

70014-20 COM4LAB Course: AC available for evaluation in tables and triangular, square-wave signal types,
diagrams. The analysis and also DC
Technology II
documentation of the experiment on Frequency range: 0.5 Hz – 100 kHz,
the student device can be done at also DC
school or at home. SYNC output: TTL clock
 can be edited and thus adapted to frequency 0.5 Hz – 100 kHz
your own lesson plan. Output voltage: max. ±10 V, (0 – 20
V)
Output current: max. ±250 mA
Perpetual course license.
 Digital 4-channel oscilloscope:
4 differential inputs
Technical data Sampling rate: 1 MS/s per channel
Bandwidth: 200 kHz
Memory depth: 1KS per channel
 Product key for activation of the Resolution: 12 Bit per channel
course licence via Time ranges from 10 μs/div to 500
https://register.leylab.de is ms/div
necessary. Later on the course can Voltage ranges from 10 mV/div to 10
be accessed and distributed from V/div
LeyLab. Trigger CH1 - CH4 and EXT
The COM4LAB course AC Technology  System requirements: (referenced to ground), in 4095
II is the second course on the - PC, tablet or smartphone with a steps, rising/falling edge
fundamentals of AC technology. It current browser  Digital analyzer:
addresses the behaviour of passive - internet access 8+1 digital signal inputs
components in various circuits. Various Input voltage TTL-compatible
combinations of coil, capacitor and Sampling frequency: 200 Hz – 2
resistance are analysed and calculated. MHz
The students are instructed on how to Memory depth: 9 Bit x 2 K
use the function generator, oscilloscope Triggering on any combination of the
and multimeters. The course comprises Technical Data: input states
20 chapters.
Additional properties
The course covers the following topics: 70000-00 COM4LAB Master Unit
 Voltage supply:
 generation of AC voltage 15 V/3 A
 characteristic variables in AC USB-C
technology  Interfaces:
 Ohmic resistance in an AC circuit WLAN
Ethernet 100 MBits RJ45
 coil in an AC circuit USB
 Extensions:
inductive resistance – series Extension Slot
connection of resistor and coil – USB Interface (type A)
parallel connection of resistor and  NFC
coil The COM4LAB Master Unit is a
multifunctional, compact, measuring  Light strip & LEDs for status display
interface. As a universal base station it is  Security lock for mechanical
 capacitor in an AC circuit used for the operation and power supply attachment and electronic activation
for the COM4LAB experiment boards of the experiment boards
and as an independent measuring
capacitive resistance – series laboratory. The Master Unit can be
 Anti-theft protection (port for
connection of resistor and Kensington lock)
simultaneously connected to up to four
capacitor – parallel connection of digital terminal devices (PC, tablet or
resistor and capacitor smartphone) for the recording of Scope of delivery
measurements and for remote control of
its built-in functions. The Master Unit can
 series connection of resistor, coil and
be quickly attached to an experiment  USB cable
capacitor
board. Its clear and structured design  NFC card
 parallel connection of resistor, coil results in easy operation.
and capacitor
 series compensation
Dimensions
 parallel compensation ACCESSORIES
 series resonance
 295 x 154 × 30 mm3
 parallel resonance

Integrated measuring instruments

The course …

 can be displayed and filled out on

 Two digital multimeters:
Voltage: DC/AC – 2 V | 20 V
your own tablet/smartphone/laptop.
Current: DC/AC – 20 mA | 200 mA |
 is platform-independent - a current 2A
browser is sufficient. Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2
 can be distributed to students via QR MΩ
codes. Autoranging for all measurement
 enables interactive experimenting: ranges
The measured values from the  Digital Function Generator:
Master Unit are automatically made digitally generated sinusoidal,
LD Didactic GmbH Technical Documentation Page 8
70000-11 USB-C Charger 45 W ADDITIONALLY REQUIRED  POWER DISSIPATION IN A TRANSISTOR
Europlug (Type C)  CHARACTERISTIC OF A
PHOTOTRANSISTOR
PC, TABLET OR SMARTPHONE WITH A
CURRENT BROWSER  DARLINGTON CONFIGURATION
 OPERATING POINT OF A TRANSISTOR

ME1.3.1 ELECTRONIC COMPONENTS I  TRANSISTOR IN A COMMON EMITTER

CIRCUIT
 TRANSISTOR IN A COMMON COLLECTOR
CIRCUIT
THE COM4LAB COURSE ENTITLED  TRANSISTOR IN A COMMON BASE
“ELECTRONIC COMPONENTS I” IS THE FIRST CIRCUIT
COURSE CONCERNING THE ACTIVE  TRANSISTOR IN TIMER CIRCUITS
ELECTRONIC COMPONENTS THAT HAVE AN
USB-C Charger with a 45 W quick AMPLIFYING EFFECT OR PERMIT CONTROL.
charge function as a power supply for the THE MOST IMPORTANT DIODE TYPES ARE
COM4LAB Master Unit. An additional PRESENTED AND THEIR BEHAVIOUR PREVIOUS
USB-A port with fast charge ensures EXPLORED. THE FUNCTIONS, CIRCUITS AND
parallel charging of one mobile device. CHARACTERISTICS OF THE NPN AND PNP KNOWLEDGE
TRANSISTORS ARE EXPLORED. THE
Technical data STUDENTS ARE INSTRUCTED ON HOW TO
USE THE FUNCTION GENERATOR, THE STUDENTS NEED TO HAVE A BASIC
OSCILLOSCOPE AND MULTIMETERS. THE KNOWLEDGE OF DC AND AC TECHNOLOGY
COURSE COMPRISES 19 CHAPTERS. AND HAVE TO BE FAMILIAR WITH THE
 45 W PD, 15 V/3 A
MEASUREMENT OF ELECTRICAL QUANTITIES
 USB-A Port DC 5 V/2,4 A IN ORDER TO BE ABLE TO COMPLETE THE
 Overvoltage protection TOTAL DURATION: UP TO 8 HOURS COURSE SUCCESSFULLY. ADDITIONALLY,
 Overheat protection DEALING WITH SIMPLE FORMULAS IS
REQUIRED.

Scope of delivery TARGET AUDIENCE

AMONG OTHERS, THE COURSE CAN BE
 2 m USB-C/USB-C cable
USED TO SUPPORT THE TRAINING PROCESS
70015-00 COM4LAB Board:
FOR THE FOLLOWING PROFESSIONS:
Electronic Components I
ALTERNATIVELY USB-C CHARGER  INFORMATION ELECTRONICS
WITH UK-PLUG OR US-PLUG TECHNICIAN
 SYSTEM ELECTRONICS TECHNICIAN

70000-22 COM4LAB Set of Safety

Leads, 2 mm, 24 pcs
LEARNING
OBJECTIVES
THE STUDENTS SHOULD:

 BE ABLE TO RECOGNISE THE SETUP,

FUNCTION AND USE OF DIODES AND
TRANSISTORS,
 BE ABLE TO RECORD CHARACTERISTICS The experiment board to the COM4LAB
OF DIODES AND TRANSISTORS USING course Electric Components I (supplied
AN OSCILLOSCOPE AND separately).
Set of highly fexible test leads with  BE FAMILIAR WITH STANDARD CIRCUITS
insulation in PVC with assembled
AND THEIR APPLICATIONS.
stackable 2 mm multilam plugs with rigid There are 12 experiment panels on the
insulating sleeve on both ends. experiment board. Each experiment
panel contains a self-contained circuit

 6 x 150 mm, red

TOPICS that is put into operation and examined
depending on the selected experiment.
 6 x 150 mm, black The active experiment panel is indicated
THE COURSE COVERS THE FOLLOWING by a lit green LED.
 2 x 150 mm, blue TOPICS:
 4 x 300 mm, red
The experiment board, housed within a
 4 x 300 mm, black sturdy board carrier, is to be used in
 DIODE CHARACTERISTICS
 2 x 300 mm, blue conjunction with, and powered by the
 CHARACTERISTIC OF A ZENER DIODE
Master Unit (supplied separately).
 CHARACTERISTIC OF A LIGHT-EMITTING Circuits are wired by using 2 mm safety
Technical data DIODE cables (supplied separately).
 DIODE BRANCHES IN A TRANSISTOR
 Rated voltage/current 600 V, CAT II /  CHARACTERISTICS OF A TRANSISTOR Dimensions
10 A
 Lead cross section 0,5 mm² INPUT CHARACTERISTIC – OUTPUT
 Circuit board: 280 × 200 mm2
CHARACTERISTIC – CONTROL
CHARACTERISTIC  Frame: 296,5 × 354 mm2

LD Didactic GmbH Technical Documentation Page 9

 Supply voltage  transistor in a common base circuit  295 x 154 × 30 mm3
 transistor in timer circuits
 +15 V DC, −15 V DC und +5 V DC Integrated measuring instruments
from the Master Unit via The course …
corresponding relays
 Two digital multimeters:
 can be displayed and filled out on Voltage: DC/AC – 2 V | 20 V
Protective functions Current: DC/AC – 20 mA | 200 mA |
your own tablet/smartphone/laptop.
2A
 is platform-independent - a current
Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2
 Integrated reverse polarity protection browser is sufficient.
MΩ
due to connection to the Master Unit  can be distributed to students via QR Autoranging for all measurement
 The use of safety cables avoids codes. ranges
unintentional short-circuiting  enables interactive experimenting:  Digital Function Generator:
The measured values from the digitally generated sinusoidal,
Master Unit are automatically made triangular, square-wave signal types,
available for evaluation in tables and also DC
diagrams. The analysis and Frequency range: 0.5 Hz – 100 kHz,
documentation of the experiment on also DC
Technical Data: the student device can be done at SYNC output: TTL clock
school or at home. frequency 0.5 Hz – 100 kHz
 can be edited and thus adapted to Output voltage: max. ±10 V, (0 – 20
your own lesson plan. V)
70015-20 COM4LAB Course: Output current: max. ±250 mA
Electronic Components I  Digital 4-channel oscilloscope:
Perpetual course license.
4 differential inputs
Sampling rate: 1 MS/s per channel
Technical data Bandwidth: 200 kHz
Memory depth: 1KS per channel
Resolution: 12 Bit per channel
 Product key for activation of the Time ranges from 10 μs/div to 500
course licence via ms/div
https://register.leylab.de is Voltage ranges from 10 mV/div to 10
necessary. Later on the course can V/div
be accessed and distributed from Trigger CH1 - CH4 and EXT
LeyLab. (referenced to ground), in 4095
 System requirements: steps, rising/falling edge
- PC, tablet or smartphone with a  Digital analyzer:
current browser 8+1 digital signal inputs
- internet access Input voltage TTL-compatible
Sampling frequency: 200 Hz – 2
MHz
Memory depth: 9 Bit x 2 K
The COM4LAB course Electronic Triggering on any combination of the
Components I is the first course input states
concerning the active electronic Technical Data:
components that have an amplifying
effect or permit control. The most Additional properties
important diode types are presented and
their behaviour explored. The functions, 70000-00 COM4LAB Master Unit
circuits and characteristics of the npn  Voltage supply:
and pnp transistors are explored. The 15 V/3 A
students are instructed on how to use the USB-C
function generator, oscilloscope and  Interfaces:
multimeters. The course comprises 19 WLAN
chapters. Ethernet 100 MBits RJ45
USB
The course covers the following topics:  Extensions:
Extension Slot
USB Interface (type A)
 diode characteristics  NFC
 characteristic of a Zener diode The COM4LAB Master Unit is a  Light strip & LEDs for status display
 characteristic of a light-emitting diode multifunctional, compact, measuring
 Security lock for mechanical
interface. As a universal base station it is attachment and electronic activation
 diode branches in a transistor
used for the operation and power supply
 characteristics of a transistor of the experiment boards
for the COM4LAB experiment boards
and as an independent measuring  Anti-theft protection (port for
laboratory. The Master Unit can be Kensington lock)
input characteristic – output
characteristic – control characteristic simultaneously connected to up to four
digital terminal devices (PC, tablet or Scope of delivery
smartphone) for the recording of
 power dissipation in a transistor measurements and for remote control of
 characteristic of a phototransistor its built-in functions. The Master Unit can  USB cable
be quickly attached to an experiment  NFC card
 Darlington configuration board. Its clear and structured design
 operating point of a transistor results in easy operation.
 transistor in a common emitter circuit
 transistor in a common collector Dimensions ACCESSORIES
circuit
LD Didactic GmbH Technical Documentation Page 10
  MOSFET
70000-11 USB-C Charger 45 W ADDITIONALLY REQUIRED
Europlug (Type C) CHARACTERISTICS – MOSFET AS
SWITCH
PC, TABLET OR SMARTPHONE WITH A
CURRENT BROWSER
 IGBT

ME1.3.2 ELECTRONIC COMPONENTS

CHARACTERISTICS – IGBT AS SWITCH
II

 DIAC
 THYRISTOR
THE COM4LAB COURSE ENTITLED
“ELECTRONIC COMPONENTS II” IS THE
SECOND COURSE CONCERNING THE ACTIVE CHARACTERISTIC – THYRISTOR IN A DC
USB-C Charger with a 45 W quick CIRCUIT – PHASE ANGLE CONTROL
ELECTRONIC COMPONENTS THAT HAVE AN
charge function as a power supply for the
AMPLIFYING EFFECT OR PERMIT CONTROL. WITH A THYRISTOR
COM4LAB Master Unit. An additional
SPECIAL TRANSISTOR TYPES AND
USB-A port with fast charge ensures
SEMICONDUCTORS FROM THE POWER
parallel charging of one mobile device.  TRIAC
ELECTRONICS SECTOR ARE USED. ONE OF
THEIR MAIN APPLICATIONS, PHASE ANGLE
Technical data CONTROL, IS EXAMINED TAKING THE CHARACTERISTIC – PHASE ANGLE
THYRISTOR AND THE TRIAC AS EXAMPLES. CONTROL WITH A TRIAC
THE STUDENTS ARE INSTRUCTED ON HOW
 45 W PD, 15 V/3 A TO USE THE FUNCTION GENERATOR,
 OSCILLOSCOPE AND MULTIMETERS. THE


USB-A Port DC 5 V/2,4 A
Overvoltage protection COURSE COMPRISES 14 CHAPTERS. PREVIOUS
 Overheat protection KNOWLEDGE
TOTAL DURATION: UP TO 5 HOURS
Scope of delivery
THE STUDENTS NEED TO HAVE A BASIC

 2 m USB-C/USB-C cable
TARGET AUDIENCE KNOWLEDGE OF DC AND AC TECHNOLOGY
AND HAVE TO BE FAMILIAR WITH THE
MEASUREMENT OF ELECTRICAL QUANTITIES
AMONG OTHERS, THE COURSE CAN BE IN ORDER TO BE ABLE TO COMPLETE THE
USED TO SUPPORT THE TRAINING PROCESS COURSE SUCCESSFULLY. ADDITIONALLY,
FOR THE FOLLOWING PROFESSIONS: DEALING WITH SIMPLE FORMULAS IS
ALTERNATIVELY USB-C CHARGER
REQUIRED.
WITH UK-PLUG OR US-PLUG
 INFORMATION ELECTRONICS
TECHNICIAN
70000-22 COM4LAB Set of Safety
 SYSTEM ELECTRONICS TECHNICIAN
Leads, 2 mm, 24 pcs
70016-00 COM4LAB Board:
Electronic Components II
LEARNING
OBJECTIVES
THE STUDENTS SHOULD:

 UNDERSTAND THE SETUP, FUNCTION

AND USE OF FIELD-EFFECT
TRANSISTORS, MOSFETS , IGBTS,
DIACS, THYRISTORS AND TRIACS
Set of highly fexible test leads with AND
insulation in PVC with assembled  BE ABLE TO RECORD CHARACTERISTICS
stackable 2 mm multilam plugs with rigid OF THESE ACTIVE COMPONENTS WITH
insulating sleeve on both ends. AN OSCILLOSCOPE.

 6 x 150 mm, red

 6 x 150 mm, black TOPICS The experiment board to the COM4LAB
course Electric Components II
 2 x 150 mm, blue (supplied separately).
 4 x 300 mm, red THE COURSE COVERS THE FOLLOWING
 4 x 300 mm, black TOPICS:
There are 13 experiment panels on the
 2 x 300 mm, blue experiment board. Each experiment
 FIELD-EFFECT TRANSISTORS panel contains a self-contained circuit
that is put into operation and examined
Technical data depending on the selected experiment.
TRANSFER CHARACTERISTIC OF THE The active experiment panel is indicated
JFET – OUTPUT CHARACTERISTIC by a lit green LED.
 Rated voltage/current 600 V, CAT II /
FAMILY OF THE JFET – JFET AS
10 A
SWITCH
 Lead cross section 0,5 mm² The experiment board, housed within a
sturdy board carrier, is to be used in

LD Didactic GmbH Technical Documentation Page 11

 conjunction with, and powered by the  MOSFET 70000-00 COM4LAB Master Unit
Master Unit (supplied separately).
Circuits are wired by using 2 mm safety
cables (supplied separately). characteristics – MOSFET as switch

Dimensions  IGBT

 Circuit board: 280 × 200 mm2 characteristics – IGBT as switch

 Frame: 296,5 × 354 mm2
 DIAC
Supply voltage  thyristor The COM4LAB Master Unit is a
multifunctional, compact, measuring
 +15 V DC, −15 V DC und +5 V DC characteristic – thyristor in a DC interface. As a universal base station it is
from the Master Unit via circuit – phase angle control with a used for the operation and power supply
corresponding relays thyristor for the COM4LAB experiment boards
and as an independent measuring
laboratory. The Master Unit can be
Protective functions  TRIAC simultaneously connected to up to four
digital terminal devices (PC, tablet or
smartphone) for the recording of
 Integrated reverse polarity protection characteristic – phase angle control
measurements and for remote control of
due to connection to the Master Unit with a TRIAC
its built-in functions. The Master Unit can
 The use of safety cables avoids be quickly attached to an experiment
unintentional short-circuiting The course … board. Its clear and structured design
results in easy operation.

 can be displayed and filled out on

your own tablet/smartphone/laptop. Dimensions
 is platform-independent - a current
Technical Data: browser is sufficient.  295 x 154 × 30 mm3
 can be distributed to students via QR
codes.
Integrated measuring instruments
70016-20 COM4LAB Course:  enables interactive experimenting:
The measured values from the
Electronic Components II Master Unit are automatically made  Two digital multimeters:
available for evaluation in tables and Voltage: DC/AC – 2 V | 20 V
diagrams. The analysis and Current: DC/AC – 20 mA | 200 mA |
documentation of the experiment on 2A
the student device can be done at Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2
school or at home. MΩ
 can be edited and thus adapted to Autoranging for all measurement
your own lesson plan. ranges
 Digital Function Generator:
digitally generated sinusoidal,
Perpetual course license.
triangular, square-wave signal types,
also DC
Technical data Frequency range: 0.5 Hz – 100 kHz,
also DC
SYNC output: TTL clock
 Product key for activation of the frequency 0.5 Hz – 100 kHz
course licence via Output voltage: max. ±10 V, (0 – 20
https://register.leylab.de is V)
necessary. Later on the course can Output current: max. ±250 mA
The COM4LAB course Electronic be accessed and distributed from
Components II is the second course LeyLab.
 Digital 4-channel oscilloscope:
4 differential inputs
concerning the active electronic  System requirements: Sampling rate: 1 MS/s per channel
components that have an amplifying - PC, tablet or smartphone with a Bandwidth: 200 kHz
effect or permit control. Special transistor current browser Memory depth: 1KS per channel
types and semiconductors from the - internet access Resolution: 12 Bit per channel
power electronics sector are used. One
Time ranges from 10 μs/div to 500
of their main applications, phase angle
ms/div
control, is examined taking the thyristor
Voltage ranges from 10 mV/div to 10
and the TRIAC as examples. The
V/div
students are instructed on how to use the
Trigger CH1 - CH4 and EXT
function generator, oscilloscope and Technical Data: (referenced to ground), in 4095
multimeters. The course comprises 14
steps, rising/falling edge
chapters.
 Digital analyzer:
8+1 digital signal inputs
The course covers the following topics: Input voltage TTL-compatible
Sampling frequency: 200 Hz – 2
MHz
 field-effect transistors
Memory depth: 9 Bit x 2 K
Triggering on any combination of the
transfer characteristic of the JFET – input states
output characteristic family of the
JFET – JFET as switch
Additional properties

LD Didactic GmbH Technical Documentation Page 12

  Voltage supply: 70000-22 COM4LAB Set of Safety  ELECTRONICS TECHNICIAN FOR
15 V/3 A Leads, 2 mm, 24 pcs INFORMATION AND SYSTEM
USB-C TECHNOLOGY
 Interfaces:  ELECTRONICS TECHNICIAN FOR
WLAN MACHINE AND DRIVE TECHNOLOGY
Ethernet 100 MBits RJ45  AIRCRAFT ELECTRONICS TECHNICIAN
USB
 INFORMATION ELECTRONICS
 Extensions: TECHNICIAN
Extension Slot
USB Interface (type A)  SYSTEM ELECTRONICS TECHNICIAN

 NFC


Light strip & LEDs for status display
Security lock for mechanical
LEARNING
attachment and electronic activation
of the experiment boards
OBJECTIVES
Set of highly fexible test leads with
 Anti-theft protection (port for insulation in PVC with assembled
Kensington lock) stackable 2 mm multilam plugs with rigid THE STUDENTS SHOULD:
insulating sleeve on both ends.
Scope of delivery  UNDERSTAND THE SETUP, FUNCTION
 6 x 150 mm, red AND FUNCTIONAL PRINCIPLE OF THE
INDIVIDUAL GATES AND OTHER LOGIC
 USB cable  6 x 150 mm, black
COMPONENTS,
 NFC card  2 x 150 mm, blue
 BE FAMILIAR WITH THE IMPORTANT
 4 x 300 mm, red LAWS OF PROPOSITIONAL LOGIC AND
 4 x 300 mm, black  BE ABLE TO PERFORM

ACCESSORIES  2 x 300 mm, blue TROUBLESHOOTING PROCEDURES ON

THE LOGIC COMPONENTS.

Technical data
70000-11 USB-C Charger 45 W
Europlug (Type C)
 Rated voltage/current 600 V, CAT II /
TOPICS
10 A
 Lead cross section 0,5 mm² THE COURSE COVERS THE FOLLOWING
TOPICS:

 TTL MODULES
ADDITIONALLY REQUIRED
AND GATE – OR GATE – NOT GATE –
PC, TABLET OR SMARTPHONE WITH A XOR GATE – NAND GATE
CURRENT BROWSER

USB-C Charger with a 45 W quick  OPERATION WITH BINARY INPUTS

charge function as a power supply for the ME1.4.1 DIGITAL TECHNOLOGY I  BASIC LAWS
COM4LAB Master Unit. An additional
USB-A port with fast charge ensures DE MORGAN'S LAWS –
parallel charging of one mobile device. ASSOCIATIVE LAW – DISTRIBUTIVE LAW
THE COM4LAB COURSE ENTITLED
“DIGITAL TECHNOLOGY I” IS THE FIRST
Technical data COURSE ON THE FUNDAMENTALS OF
 KARNAUGH MAP
DIGITAL TECHNOLOGY. THE FUNDAMENTALS
AND LAWS OF BOOLEAN ALGEBRA ARE  BINARY CODE
 45 W PD, 15 V/3 A
DESCRIBED USING LOGIC OPERATIONS. THE  SEVEN-SEGMENT DISPLAY
 USB-A Port DC 5 V/2,4 A COURSE, COMPRISING 16 CHAPTERS, ALSO  HALF ADDER
 Overvoltage protection EXAMINES THE TROUBLESHOOTING
 FULL ADDER
 Overheat protection PROCEDURE IN DETAIL.
 MULTIPLEXER AND DEMULTIPLEXER

TOTAL DURATION: 6 HOURS

 FAULT SIMULATION
Scope of delivery

 2 m USB-C/USB-C cable TARGET AUDIENCE PREVIOUS

KNOWLEDGE
AMONG OTHERS, THE COURSE CAN BE
ALTERNATIVELY USB-C CHARGER USED TO SUPPORT THE TRAINING PROCESS
FOR THE FOLLOWING PROFESSIONS: THE STUDENTS DO NOT NEED ANY
WITH UK-PLUG OR US-PLUG
PREVIOUS KNOWLEDGE OF DIGITAL
TECHNOLOGY IN ORDER TO BE ABLE TO
 ELECTRONICS TECHNICIAN FOR COMPLETE THE COURSE SUCCESSFULLY.
AUTOMATION TECHNOLOGY DEALING WITH SIMPLE FORMULAS IS,
 ELECTRONICS TECHNICIAN FOR HOWEVER, REQUIRED.
ENERGY AND BUILDING TECHNOLOGY
 ELECTRONICS TECHNICIAN FOR
DEVICES AND SYSTEMS

LD Didactic GmbH Technical Documentation Page 13

70017-00 COM4LAB Board: 70017-20 COM4LAB Course: Technical data
Digital Technology I Digital Technology I
 Product key for activation of the
course licence via
https://register.leylab.de is
necessary. Later on the course can
be accessed and distributed from
LeyLab.
 System requirements:
- PC, tablet or smartphone with a
current browser
- internet access

Technical Data:

The experiment board to the COM4LAB The COM4LAB course Digital

course Digital Technology I (supplied Technology I is the first course on the
separately). fundamentals of digital technology. The 70000-00 COM4LAB Master Unit
fundamentals and laws of Boolean
algebra are described using logic
There are several experiment panels on
operations. The course, comprising 16
the experiment board. Each experiment
chapters, also examines the
panel contains a group of electronic
troubleshooting procedure in detail.
components that usually build up a
circuit. Experiment panels are put into
operation and examined depending on The course covers the following topics:
the selected experiment. The active
experiment panels are indicated by a lit
green LED.  TTL modules
The COM4LAB Master Unit is a
The experiment board, housed within a AND gate – OR gate – NOT gate – multifunctional, compact, measuring
sturdy board carrier, is to be used in XOR gate – NAND gate interface. As a universal base station it is
conjunction with, and powered by the used for the operation and power supply
Master Unit (supplied separately). for the COM4LAB experiment boards
Circuits are wired by using 2 mm safety  operation with binary inputs and as an independent measuring
cables (supplied separately).  basic laws laboratory. The Master Unit can be
simultaneously connected to up to four
digital terminal devices (PC, tablet or
Dimensions De Morgan's laws – associative
smartphone) for the recording of
law – distributive law
measurements and for remote control of
 Circuit board: 280 × 200 mm2 its built-in functions. The Master Unit can
 Karnaugh map be quickly attached to an experiment
 Frame: 296,5 × 354 mm2 board. Its clear and structured design
 binary code
results in easy operation.
Supply voltage  seven-segment display
 half adder
Dimensions
 full adder
 +5 V DC from the Master Unit
 multiplexer and demultiplexer
 295 x 154 × 30 mm3
 fault simulation
Protective functions
Integrated measuring instruments
The course …
 Integrated reverse polarity protection
due to connection to the Master Unit  Two digital multimeters:
 The use of safety cables avoids  can be displayed and filled out on Voltage: DC/AC – 2 V | 20 V
unintentional short-circuiting your own tablet/smartphone/laptop. Current: DC/AC – 20 mA | 200 mA |
 is platform-independent - a current 2A
browser is sufficient. Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2
 can be distributed to students via QR MΩ
codes. Autoranging for all measurement
 enables interactive experimenting: ranges
Technical Data: The measured values from the  Digital Function Generator:
Master Unit are automatically made digitally generated sinusoidal,
available for evaluation in tables and triangular, square-wave signal types,
diagrams. The analysis and also DC
documentation of the experiment on Frequency range: 0.5 Hz – 100 kHz,
the student device can be done at also DC
school or at home. SYNC output: TTL clock
 can be edited and thus adapted to frequency 0.5 Hz – 100 kHz
Output voltage: max. ±10 V, (0 – 20
your own lesson plan.
V)
Output current: max. ±250 mA
Perpetual course license.  Digital 4-channel oscilloscope:
4 differential inputs
LD Didactic GmbH Technical Documentation Page 14
 Sampling rate: 1 MS/s per channel  Overvoltage protection
Bandwidth: 200 kHz
Memory depth: 1KS per channel  Overheat protection
TARGET AUDIENCE
Resolution: 12 Bit per channel
Time ranges from 10 μs/div to 500 Scope of delivery AMONG OTHERS, THE COURSE CAN BE
ms/div USED TO SUPPORT THE TRAINING PROCESS
Voltage ranges from 10 mV/div to 10 FOR THE FOLLOWING PROFESSIONS:
V/div  2 m USB-C/USB-C cable
Trigger CH1 - CH4 and EXT
(referenced to ground), in 4095
 ELECTRONICS TECHNICIAN FOR
AUTOMATION TECHNOLOGY
steps, rising/falling edge
 Digital analyzer: ALTERNATIVELY USB-C CHARGER  ELECTRONICS TECHNICIAN FOR
ENERGY AND BUILDING TECHNOLOGY
8+1 digital signal inputs WITH UK-PLUG OR US-PLUG
Input voltage TTL-compatible  ELECTRONICS TECHNICIAN FOR
Sampling frequency: 200 Hz – 2 DEVICES AND SYSTEMS
MHz 70000-22 COM4LAB Set of Safety  ELECTRONICS TECHNICIAN FOR
Memory depth: 9 Bit x 2 K Leads, 2 mm, 24 pcs INFORMATION AND SYSTEM
Triggering on any combination of the TECHNOLOGY
input states  ELECTRONICS TECHNICIAN FOR
MACHINE AND DRIVE TECHNOLOGY
Additional properties  AIRCRAFT ELECTRONICS TECHNICIAN
 INFORMATION ELECTRONICS
TECHNICIAN
 Voltage supply:
15 V/3 A  SYSTEM ELECTRONICS TECHNICIAN
USB-C
 Interfaces:
WLAN
Ethernet 100 MBits RJ45
LEARNING
USB
Set of highly fexible test leads with
OBJECTIVES
 Extensions:
Extension Slot insulation in PVC with assembled
USB Interface (type A) stackable 2 mm multilam plugs with rigid THE STUDENTS SHOULD:
 NFC insulating sleeve on both ends.
 Light strip & LEDs for status display  BE ABLE TO UNDERSTAND THE SETUP,
 Security lock for mechanical  6 x 150 mm, red FUNCTION AND FUNCTIONAL PRINCIPLE
attachment and electronic activation  6 x 150 mm, black OF THE INDIVIDUAL FLIP-FLOPS,
of the experiment boards  2 x 150 mm, blue  BECOME FAMILIAR WITH USE OF FLIP-
 Anti-theft protection (port for  4 x 300 mm, red
FLOPS AND OTHER MULTIVIBRATORS
Kensington lock) AND
 4 x 300 mm, black
 BE ABLE TO PERFORM
 2 x 300 mm, blue TROUBLESHOOTING PROCEDURES ON
Scope of delivery
THE LOGIC COMPONENTS.
Technical data
 USB cable
 NFC card
 Rated voltage/current 600 V, CAT II /
TOPICS
10 A
 Lead cross section 0,5 mm² THE COURSE COVERS THE FOLLOWING
TOPICS:
ACCESSORIES

70000-11 USB-C Charger 45 W ADDITIONALLY REQUIRED  BISTABLE MULTIVIBRATORS

Europlug (Type C)
SR FLIP-FLOP – CLOCKED SR FLIP-
PC, TABLET OR SMARTPHONE WITH A FLOP – D FLIP-FLOP – JK FLIP-FLOP –
CURRENT BROWSER JK MASTER-SLAVE FLIP-FLOP

ME1.4.2 DIGITAL TECHNOLOGY II  MONOSTABLE AND ASTABLE

MULTIVIBRATOR
 SCHMITT TRIGGER
THE COM4LAB COURSE ENTITLED
 FLIP-FLOP APPLICATIONS

“DIGITAL TECHNOLOGY II” IS THE SECOND

COURSE ON THE FUNDAMENTALS OF FREQUENCY DIVIDER – COUNTER –
DIGITAL TECHNOLOGY. THIS COURSE SHIFT REGISTER – PARALLEL-SERIAL
USB-C Charger with a 45 W quick EXPLORES SEVERAL FLIP-FLOP TYPES AND CONVERTER
charge function as a power supply for the VARIOUS FLIP-FLOP APPLICATIONS SUCH AS
COM4LAB Master Unit. An additional COUNTERS, SHIFT REGISTERS AND
USB-A port with fast charge ensures
parallel charging of one mobile device.
PARALLEL-SERIAL CONVERTERS. THE
COURSE, COMPRISING 12 CHAPTERS, ALSO
PREVIOUS
EXAMINES THE TROUBLESHOOTING
Technical data PROCEDURE IN DETAIL. KNOWLEDGE
 45 W PD, 15 V/3 A TOTAL DURATION: 5 HOURS THE STUDENTS DO NOT NEED ANY
PREVIOUS KNOWLEDGE OF DIGITAL
 USB-A Port DC 5 V/2,4 A
LD Didactic GmbH Technical Documentation Page 15
 TECHNOLOGY IN ORDER TO BE ABLE TO 70018-20 COM4LAB Course: be accessed and distributed from
COMPLETE THE COURSE SUCCESSFULLY. LeyLab.
Digital Technology II
DEALING WITH SIMPLE FORMULAS IS,  System requirements:
HOWEVER, REQUIRED. - PC, tablet or smartphone with a
current browser
- internet access

70018-00 COM4LAB Board:

Digital Technology II
Technical Data:

70000-00 COM4LAB Master Unit

The COM4LAB course Digital

Technology II is the second course on
the fundamentals of digital technology.
This course explores several flip-flop
types and various flip-flop applications
such as counters, shift registers and
parallel-serial converters. The course,
comprising 12 chapters, also examines The COM4LAB Master Unit is a
The experiment board to the COM4LAB the troubleshooting procedure in detail. multifunctional, compact, measuring
courses Digital Technology II and interface. As a universal base station it is
Automotive Digital Technology II The course covers the following topics: used for the operation and power supply
(supplied separately). for the COM4LAB experiment boards
and as an independent measuring
 bistable multivibrators laboratory. The Master Unit can be
There are several experiment panels on simultaneously connected to up to four
the experiment board. Each experiment digital terminal devices (PC, tablet or
panel contains a group of electronic SR flip-flop – clocked SR flip-flop – D smartphone) for the recording of
components that usually build up a flip-flop – JK flip-flop – JK master- measurements and for remote control of
circuit. Experiment panels are put into slave flip-flop its built-in functions. The Master Unit can
operation and examined depending on be quickly attached to an experiment
the selected experiment. The active board. Its clear and structured design
experiment panels are indicated by a lit  monostable and astable multivibrator
results in easy operation.
green LED.  Schmitt trigger
 flip-flop applications
Dimensions
The experiment board, housed within a
sturdy board carrier, is to be used in frequency divider – counter – shift
conjunction with, and powered by the register – parallel-serial converter  295 x 154 × 30 mm3
Master Unit (supplied separately).
Circuits are wired by using 2 mm safety
cables (supplied separately). The course … Integrated measuring instruments

Dimensions  can be displayed and filled out on  Two digital multimeters:

your own tablet/smartphone/laptop. Voltage: DC/AC – 2 V | 20 V
Current: DC/AC – 20 mA | 200 mA |
 Circuit board: 280 × 200 mm2  is platform-independent - a current
2A
browser is sufficient.
 Frame: 296,5 × 354 mm2 Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2
 can be distributed to students via QR MΩ
codes. Autoranging for all measurement
Supply voltage  enables interactive experimenting: ranges
The measured values from the  Digital Function Generator:
 +5 V DC from the Master Unit Master Unit are automatically made digitally generated sinusoidal,
available for evaluation in tables and triangular, square-wave signal types,
diagrams. The analysis and also DC
Protective functions documentation of the experiment on Frequency range: 0.5 Hz – 100 kHz,
the student device can be done at also DC
school or at home. SYNC output: TTL clock
 Integrated reverse polarity protection
due to connection to the Master Unit  can be edited and thus adapted to frequency 0.5 Hz – 100 kHz
your own lesson plan. Output voltage: max. ±10 V, (0 – 20
 The use of safety cables avoids V)
unintentional short-circuiting Output current: max. ±250 mA
Perpetual course license.
 Digital 4-channel oscilloscope:
4 differential inputs
Technical data Sampling rate: 1 MS/s per channel
Bandwidth: 200 kHz
Technical Data: Memory depth: 1KS per channel
 Product key for activation of the Resolution: 12 Bit per channel
course licence via Time ranges from 10 μs/div to 500
https://register.leylab.de is ms/div
necessary. Later on the course can Voltage ranges from 10 mV/div to 10
LD Didactic GmbH Technical Documentation Page 16
 V/div  2 m USB-C/USB-C cable
Trigger CH1 - CH4 and EXT
(referenced to ground), in 4095 7009101 COM3LAB Course:
steps, rising/falling edge Protoboard II - COM4LAB
 Digital analyzer: ALTERNATIVELY USB-C CHARGER ready
8+1 digital signal inputs
WITH UK-PLUG OR US-PLUG
Input voltage TTL-compatible
Sampling frequency: 200 Hz – 2
MHz 70000-22 COM4LAB Set of Safety
Memory depth: 9 Bit x 2 K
Triggering on any combination of the
Leads, 2 mm, 24 pcs
input states

Additional properties

 Voltage supply:
15 V/3 A
USB-C
 Interfaces:
WLAN
Ethernet 100 MBits RJ45
USB
Comprises an experiment board, housed
 Extensions: Set of highly fexible test leads with within a board carrier, for use in
Extension Slot insulation in PVC with assembled conjunction with, and powered by the
USB Interface (type A) stackable 2 mm multilam plugs with rigid Master Unit (700020, supplied
 NFC insulating sleeve on both ends. separately), the Protoboard II expands
 Light strip & LEDs for status display the console into a development platform
for electronic circuits. Any type of circuit
 Security lock for mechanical  6 x 150 mm, red with electronic components (not
attachment and electronic activation
 6 x 150 mm, black included) can be set up and tested on
of the experiment boards the breadboard with 1 mm contacts. The
 Anti-theft protection (port for
 2 x 150 mm, blue
fixed voltage outputs and the function
Kensington lock)  4 x 300 mm, red generator output are connected via 2 mm
 4 x 300 mm, black sockets and can be switched using slide
Scope of delivery  2 x 300 mm, blue switches. There are 2 change-over
switches for any desired connections
located on the prototyping board.
Technical data Furthermore, standard European printed
 USB cable
circuit boards can be connected using a
 NFC card
64-pin VG terminal strip. 8 relay
 Rated voltage/current 600 V, CAT II /
switchover contacts are located on the
10 A
VG terminal strip. 8 digital outputs can be
 Lead cross section 0,5 mm² tapped using the VG strip or via 2 mm
ACCESSORIES sockets. The relay and digital outputs
can be switched using software. The
70000-11 USB-C Charger 45 W power supply, the multimeter and the
ADDITIONALLY REQUIRED function generator of the console can be
Europlug (Type C) operated without the PC.
PC, TABLET OR SMARTPHONE WITH A
Additionally required
CURRENT BROWSER

ME1.5.1 PROTOBOARD II  Protoboard II Accessories (7009102)

THE PROTOBOARD II EXPANDS THE

The COM3LAB software contains
COM4LAB MASTER UNIT INTO A
courses in all supported languages and
DEVELOPMENT PLATFORM FOR ELECTRONIC
the current version can be downloaded
USB-C Charger with a 45 W quick CIRCUITS. ANY TYPE OF CIRCUIT WITH
from www.ld-didactic.de for free.
charge function as a power supply for the ELECTRONIC COMPONENTS (NOT INCLUDED)
Alternatively, the COM3LAB software
COM4LAB Master Unit. An additional CAN BE SET UP AND TESTED ON THE
can also be obtained on DVD
USB-A port with fast charge ensures BREADBOARD WITH 1 MM CONTACTS.
(70000CBT).
parallel charging of one mobile device.

Technical data
LEARNING OBJECTIVES

 45 W PD, 15 V/3 A
 INDEPENDENT SETUP AND
EXAMINATION OF THE ELECTRONIC
 USB-A Port DC 5 V/2,4 A CIRCUITS
 Overvoltage protection  USE OF THE FUNCTION GENERATOR,
 Overheat protection THE MULTIMETER AND THE
OSCILLOSCOPE

Scope of delivery

LD Didactic GmbH Technical Documentation Page 17

70000CBT DVD: COM3LAB Alternatively, the software Input voltage TTL-compatible
Sampling frequency: 200 Hz – 2
Software can be downloaded free of MHz
charge at SOFTWARE Memory depth: 9 Bit x 2 K
Triggering on any combination of the
DOWNLOAD and is updated input states
regularly.
Additional properties
70000-00 COM4LAB Master Unit
 Voltage supply:
15 V/3 A
USB-C
 Interfaces:
WLAN
Ethernet 100 MBits RJ45
COM3LAB software package for Master USB
Unit 2.0 (700020) and 70000USB
 Extensions:
Extension Slot
DVD contains: USB Interface (type A)
The COM4LAB Master Unit is a  NFC
 All available COM3LAB courses in all multifunctional, compact, measuring  Light strip & LEDs for status display
available languages interface. As a universal base station it is  Security lock for mechanical
 COM3LAB starter software used for the operation and power supply attachment and electronic activation
for the COM4LAB experiment boards of the experiment boards
 COM3LAB configurator and as an independent measuring
 USB driver software for Master Unit
 Anti-theft protection (port for
laboratory. The Master Unit can be Kensington lock)
2.0 simultaneously connected to up to four
 .NET 4.0 digital terminal devices (PC, tablet or
smartphone) for the recording of Scope of delivery
 Separate installation for the audio
package in all available languages measurements and for remote control of
its built-in functions. The Master Unit can
be quickly attached to an experiment  USB cable
For each COM3LAB multimedia course board. Its clear and structured design  NFC card
there is an electronic, interactive results in easy operation.
instruction manual. The contents of the
manual are dependent on the topic and
are tailored to the hardware. The Dimensions
ACCESSORIES
operation and function of the manuals
are identical for all courses. The 32-bit  295 x 154 × 30 mm3
user interface, into which the interactive 7009102 COM3LAB: Protoboard II
manual, the virtual lab and the tools are Accessories
integrated, also remains the same for all Integrated measuring instruments
courses. Structure of multimedia course
software:
 Two digital multimeters: Required accessories for the COM3LAB
Voltage: DC/AC – 2 V | 20 V Course Protoboard II (7009101).
 Electronic manual Current: DC/AC – 20 mA | 200 mA |
 The same look and the same 2A
Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2 Scope of Delivery
operation for all courses
MΩ
 Quick and easy installation Autoranging for all measurement
 Virtual lab (oscilloscope, multimeters, ranges
 350 wire jumpers for interconnecting
the components (1 mm, length
function generator etc.)  Digital Function Generator: between 0.5 and 12 cm)
 Tools (printers, calculators, word digitally generated sinusoidal,
 20 adapter leads, 1 mm/2 mm for the
processing, copy function for triangular, square-wave signal types,
connection of the measuring points
measurement results) also DC
to the inputs of the measuring
 Help Frequency range: 0.5 Hz – 100 kHz,
instruments
also DC
 Glossary
SYNC output: TTL clock  5 probe tips with 2-mm terminal
 Table of contents frequency 0.5 Hz – 100 kHz socket
 Language (English, French, etc.) can Output voltage: max. ±10 V, (0 – 20  5 cabels (2 mm, length 30 cm)
be switched by pressing a button V)
 Readings and texts can be used in Output current: max. ±250 mA
your own documents  Digital 4-channel oscilloscope:
 Zoomable 4 differential inputs
Sampling rate: 1 MS/s per channel
 Free selectable chapters Bandwidth: 200 kHz Scope of delivery:
 Status display (successfully Memory depth: 1KS per channel
processed, not processed) Resolution: 12 Bit per channel
 Evaluation of measurements and Time ranges from 10 μs/div to 500
tasks ms/div
 Evaluation of the circuitry Voltage ranges from 10 mV/div to 10
V/div
Trigger CH1 - CH4 and EXT
(referenced to ground), in 4095
steps, rising/falling edge
 Digital analyzer:
Additionally required: 8+1 digital signal inputs
LD Didactic GmbH Technical Documentation Page 18
70000-11 USB-C Charger 45 W ADDITIONALLY REQUIRED
Europlug (Type C)
PC WITH WINDOWS 7/8/10 64 BIT
EDITION AND ONE FREE USB
INTERFACE

USB-C Charger with a 45 W quick

charge function as a power supply for the
COM4LAB Master Unit. An additional
USB-A port with fast charge ensures
parallel charging of one mobile device.

Technical data

 45 W PD, 15 V/3 A
 USB-A Port DC 5 V/2,4 A
 Overvoltage protection
 Overheat protection

Scope of delivery

 2 m USB-C/USB-C cable

ALTERNATIVELY USB-C CHARGER

WITH UK-PLUG OR US-PLUG

70000-22 COM4LAB Set of Safety

Leads, 2 mm, 24 pcs

Set of highly fexible test leads with

insulation in PVC with assembled
stackable 2 mm multilam plugs with rigid
insulating sleeve on both ends.

 6 x 150 mm, red

 6 x 150 mm, black
 2 x 150 mm, blue
 4 x 300 mm, red
 4 x 300 mm, black
 2 x 300 mm, blue

Technical data

 Rated voltage/current 600 V, CAT II /

10 A
 Lead cross section 0,5 mm²

LD Didactic GmbH Technical Documentation Page 19

ME2.1.2 THREE-PHASE TECHNOLOGY resistors are analysed and evaluated in  Star circuit with resistors
different combinations. An 8-channel
oscilloscope enables the simultaneous  Delta circuit with resistors
measurement of all voltages and  Capacitors
THE COM3LAB COURSE "THREE-PHASE currents in the three-phase system.  Load resistors
TECHNOLOGY" DEALS WITH THE BASES AND
KEY PARAMETERS OF THREE-PHASE Curriculum Coverage
CURRENT. A THREE-PHASE GENERATOR
ENABLES PRACTICAL EXPERIMENTATION.
 Characteristics of a three-phase
70000CBT DVD: COM3LAB
THE DIFFERENCES BETWEEN A STAR AND A Software
system
DELTA CIRCUIT ARE ANALYZED IN VARIOUS
TESTS. CURRENTS, VOLTAGES AND  Representation of line diagrams &
OUTPUTS ARE MEASURED WITH phase relationships
SYMMETRICAL AND UNSYMMETRICAL LOAD.  Star- & delta circuits with different
AN OSCILLOSCOPE WITH 8 CHANNELS loads
ENABLES PHASE AND LINE VOLTAGES /
 Measurement of phase & line
CURRENTS TO BE SHOWN AT THE SAME
voltage/current
TIME.
 Ohmic load
 Symmetrical & asymmetrical charges
LEARNING OBJECTIVES  Measurement of power in the three-
phase system
THE STUDENTS SHOULD BE ABLE TO USE
THE THREE-PHASE CURRENT. Virtual Laboratory COM3LAB software package for Master
Unit 2.0 (700020) and 70000USB
TOPICS  Spectrum analyser
 Frequency counter DVD contains:

THE COURSE COVERS THE FOLLOWING  Multimeters (x2)

TOPICS:  Function generator  All available COM3LAB courses in all
 Digital memory oscilloscope available languages

 KEY PARAMETERS OF THREE-PHASE  Multiplexer for recording four  COM3LAB starter software
TECHNOLOGY voltages and four currents  COM3LAB configurator
 STAR AND TRIANGULAR SYMMETRICAL  USB driver software for Master Unit
LOAD Additional Functions 2.0
 STAR AND TRIANGULAR  .NET 4.0
UNSYMMETRICAL LOAD
 Word processing  Separate installation for the audio
 POWER MEASUREMENT package in all available languages
 Printer
 COMPENSATION OF THE PHASE SHIFT  Calculator
 CONNECTION OF A THREE-PHASE For each COM3LAB multimedia course
 Free experimentation there is an electronic, interactive
MOTOR
 Glossary instruction manual. The contents of the
 ROTARY FIELD MEASURING
manual are dependent on the topic and
INSTRUMENT
are tailored to the hardware. The
operation and function of the manuals
are identical for all courses. The 32-bit
The experiment board is placed in a user interface, into which the interactive
stable course frame. The Master Unit manual, the virtual lab and the tools are
7002401 COM3LAB Course: (700020, sold separately) is slid onto the integrated, also remains the same for all
Three-Phase Technology - course frame and connected to the courses. Structure of multimedia course
board. The security lock ensures secure software:
COM4LAB ready communication.

 Electronic manual
The power supply and control of the
experimental board is provided by the
 The same look and the same
operation for all courses
Master Unit. The experiments are wired
with 2 mm safety cables (700022, sold  Quick and easy installation
separately).  Virtual lab (oscilloscope, multimeters,
function generator etc.)
Course content, experiment instructions  Tools (printers, calculators, word
and tasks are taught via course-specific processing, copy function for
software. measurement results)
 Help
The COM3LAB software contains  Glossary
courses in all supported languages and  Table of contents
the current version can be downloaded
from www.ld-didactic.de for free.
 Language (English, French, etc.) can
be switched by pressing a button
Alternatively, the COM3LAB software
Course investigating the basics of a can also be obtained on DVD  Readings and texts can be used in
(70000CBT). your own documents
three-phase system. Practical exercises
show, for example, the generation of the  Zoomable
rotating fields or the function of the  Free selectable chapters
transformer. Furthermore, passive  Status display (successfully
components in different circuits are processed, not processed)
discussed. Coils, capacitors and
Technical Data:
LD Didactic GmbH Technical Documentation Page 20
  Evaluation of measurements and Resolution: 12 Bit per channel Scope of delivery
tasks Time ranges from 10 μs/div to 500
ms/div
 Evaluation of the circuitry
Voltage ranges from 10 mV/div to 10  2 m USB-C/USB-C cable
V/div
Trigger CH1 - CH4 and EXT
(referenced to ground), in 4095
steps, rising/falling edge ALTERNATIVELY USB-C CHARGER
Additionally required:  Digital analyzer: WITH UK-PLUG OR US-PLUG
8+1 digital signal inputs
Alternatively, the software Input voltage TTL-compatible
can be downloaded free of Sampling frequency: 200 Hz – 2 70000-22 COM4LAB Set of Safety
MHz Leads, 2 mm, 24 pcs
charge at SOFTWARE Memory depth: 9 Bit x 2 K
DOWNLOAD and is updated Triggering on any combination of the
input states
regularly.
Additional properties
70000-00 COM4LAB Master Unit
 Voltage supply:
15 V/3 A
USB-C
 Interfaces:
WLAN
Ethernet 100 MBits RJ45
USB Set of highly fexible test leads with
 Extensions: insulation in PVC with assembled
Extension Slot stackable 2 mm multilam plugs with rigid
USB Interface (type A) insulating sleeve on both ends.
The COM4LAB Master Unit is a  NFC
multifunctional, compact, measuring
interface. As a universal base station it is  Light strip & LEDs for status display  6 x 150 mm, red
used for the operation and power supply  Security lock for mechanical  6 x 150 mm, black
for the COM4LAB experiment boards attachment and electronic activation  2 x 150 mm, blue
and as an independent measuring of the experiment boards
 4 x 300 mm, red
laboratory. The Master Unit can be  Anti-theft protection (port for
simultaneously connected to up to four Kensington lock)
 4 x 300 mm, black
digital terminal devices (PC, tablet or  2 x 300 mm, blue
smartphone) for the recording of
measurements and for remote control of Scope of delivery
Technical data
its built-in functions. The Master Unit can
be quickly attached to an experiment  USB cable
board. Its clear and structured design  Rated voltage/current 600 V, CAT II /
results in easy operation.  NFC card
10 A
 Lead cross section 0,5 mm²
Dimensions
ACCESSORIES
 295 x 154 × 30 mm3
ADDITIONALLY REQUIRED
70000-11 USB-C Charger 45 W
Integrated measuring instruments Europlug (Type C)
PC WITH WINDOWS 7/8/10 64 BIT
EDITION AND ONE FREE USB
 Two digital multimeters: INTERFACE
Voltage: DC/AC – 2 V | 20 V
Current: DC/AC – 20 mA | 200 mA |
2A ME2.1.3 ASYNCHRONOUS MACHINES
Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2
MΩ
Autoranging for all measurement
ranges THE COM4LAB COURSE ENTITLED
 Digital Function Generator: “ASYNCHRONOUS MACHINES” IS THE FIRST
digitally generated sinusoidal, COURSE TO THE FASCINATING WORLD OF
triangular, square-wave signal types, ELECTRICAL MACHINES. THE
USB-C Charger with a 45 W quick
also DC charge function as a power supply for the PERFORMANCE OF THE ASYNCHRONOUS
Frequency range: 0.5 Hz – 100 kHz, MACHINES IS EXPLAINED ON A PHYSICAL-
COM4LAB Master Unit. An additional
also DC USB-A port with fast charge ensures MECHANICAL LEVEL AS WELL AS EXAMINED
SYNC output: TTL clock parallel charging of one mobile device.
BY RECORDING CHARACTERISTICS USING
frequency 0.5 Hz – 100 kHz AN INTEGRATED MACHINE TEST SYSTEM.
Output voltage: max. ±10 V, (0 – 20 TERMINAL CONNECTIONS, CHANGING OF
V) Technical data ROTATIONAL DIRECTION AND SPEED
Output current: max. ±250 mA CONTROL ARE PRACTICALLY DEVISED USING
 Digital 4-channel oscilloscope: A NUMBER OF EXPERIMENTS. THE COURSE
 45 W PD, 15 V/3 A COMPRISES 10 CHAPTERS.
4 differential inputs
Sampling rate: 1 MS/s per channel  USB-A Port DC 5 V/2,4 A
Bandwidth: 200 kHz  Overvoltage protection TOTAL DURATION: UP TO 10 HOURS
Memory depth: 1KS per channel  Overheat protection

LD Didactic GmbH Technical Documentation Page 21

 70025-00 COM4LAB Board: 70025-20 COM4LAB Course:
TARGET AUDIENCE Electrical Machines Asynchronous Machines

AMONG OTHERS, THE COURSE CAN BE

USED TO SUPPORT THE TRAINING PROCESS
FOR THE FOLLOWING PROFESSIONS:

 ELECTRICAL SYSTEM FITTER

 ELECTRONICS TECHNICIAN FOR
MACHINE AND DRIVE TECHNOLOGY

LEARNING
OBJECTIVES
THE STUDENTS ARE TO:
The experiment board to the COM4LAB The COM4LAB course Asynchronous
courses Asynchronous Machines, Machines is the first course to the
 BE ABLE TO RECOGNISE THE BASIC
Synchronous Machines and DC fascinating world of electrical machines.
PHYSICAL PRINCIPLES OF
Machines (supplied separately). The performance of the asynchronous
ASYNCHRONOUS MACHINES AND
machines is explained on a physical-
 BE ABLE TO RECORD THE mechanical level as well as examined by
CHARACTERISTICS OF ASYNCHRONOUS There are several function blocks on the
recording characteristics using an
MACHINES. experiment board, which are put into
integrated machine test system. Terminal
operation and also interconnected with
connections, changing of rotational
each other depending on the selected
direction and speed control are
experiment. The resulting circuits are
TOPICS investigated in the course of the
practically devised using a number of
experiments. The course comprises 10
corresponding experiments. The active
chapters.
function blocks are indicated by a lit
THE COURSE COVERS THE FOLLOWING
green LED.
TOPICS:
The course covers the following topics:
The experiment board, housed within a
 DESIGN sturdy board carrier, is to be used in  design
 FUNCTION conjunction with, and powered by the
Master Unit (supplied separately).
 function
 SLIP
 slip
Circuits are wired by using 2 mm safety
 STAR-DELTA START cables (supplied separately).  star-delta start
 ROTATIONAL DIRECTION
 rotational direction
 TORQUE-SPEED CHARACTERISTIC Dimensions  torque-speed characteristic
 BREAKDOWN TORQUE
 breakdown torque
 POWER CHARACTERISTIC

 Circuit board: 280 × 200 mm2 power characteristic
 SPEED CONTROL

 Frame: 296,5 × 354 mm2 speed control
 CONTROL CHARACTERISTIC
 control characteristic
Supply voltage

PREVIOUS The course …

 +15 V DC, −15 V DC und +5 V DC
KNOWLEDGE from the Master Unit  can be displayed and filled out on
your own tablet/smartphone/laptop.

THE STUDENTS NEED BASIC KNOWLEDGE IN Protective functions  is platform-independent - a current

browser is sufficient.
THE AREAS OF DC AND AC TECHNOLOGY
AS WELL AS BASIC KNOWLEDGE OF  can be distributed to students via QR
 The use of safety cables avoids codes.
ELECTROMAGNETISM IN ORDER TO BE ABLE
unintentional short-circuiting
TO COMPLETE THE COURSE  enables interactive experimenting:
SUCCESSFULLY. THEY SHOULD BE FAMILIAR The measured values from the
WITH THE MEASUREMENT OF ELECTRICAL Master Unit are automatically made
QUANTITIES. IN ADDITION, DEALING WITH available for evaluation in tables and
SIMPLE FORMULAS IS REQUIRED. diagrams. The analysis and
documentation of the experiment on
the student device can be done at
school or at home.
 can be edited and thus adapted to
your own lesson plan.

Perpetual course license.

Technical data

 Product key for activation of the

course licence via

LD Didactic GmbH Technical Documentation Page 22

 https://register.leylab.de is  Digital analyzer: ALTERNATIVELY USB-C CHARGER
necessary. Later on the course can 8+1 digital signal inputs WITH UK-PLUG OR US-PLUG
be accessed and distributed from Input voltage TTL-compatible
LeyLab. Sampling frequency: 200 Hz – 2
 System requirements: MHz 70000-22 COM4LAB Set of Safety
- PC, tablet or smartphone with a Memory depth: 9 Bit x 2 K Leads, 2 mm, 24 pcs
current browser Triggering on any combination of the
- internet access input states

Additional properties
70000-00 COM4LAB Master Unit
 Voltage supply:
15 V/3 A
USB-C
 Interfaces:
WLAN
Ethernet 100 MBits RJ45
USB
 Extensions: Set of highly fexible test leads with
Extension Slot insulation in PVC with assembled
USB Interface (type A) stackable 2 mm multilam plugs with rigid
 NFC insulating sleeve on both ends.
The COM4LAB Master Unit is a
multifunctional, compact, measuring  Light strip & LEDs for status display
interface. As a universal base station it is  Security lock for mechanical  6 x 150 mm, red
used for the operation and power supply attachment and electronic activation  6 x 150 mm, black
for the COM4LAB experiment boards of the experiment boards
and as an independent measuring  2 x 150 mm, blue
 Anti-theft protection (port for
 4 x 300 mm, red
laboratory. The Master Unit can be Kensington lock)
simultaneously connected to up to four  4 x 300 mm, black
digital terminal devices (PC, tablet or
Scope of delivery
 2 x 300 mm, blue
smartphone) for the recording of
measurements and for remote control of
its built-in functions. The Master Unit can Technical data
be quickly attached to an experiment  USB cable
board. Its clear and structured design  NFC card
results in easy operation.  Rated voltage/current 600 V, CAT II /
10 A

Dimensions
 Lead cross section 0,5 mm²
ACCESSORIES
 295 x 154 × 30 mm3
70000-11 USB-C Charger 45 W ADDITIONALLY REQUIRED
Europlug (Type C)
Integrated measuring instruments
PC, TABLET OR SMARTPHONE WITH A
 Two digital multimeters: CURRENT BROWSER
Voltage: DC/AC – 2 V | 20 V
Current: DC/AC – 20 mA | 200 mA | ME2.1.4 SYNCHRONOUS MACHINES
2A
Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2
MΩ
Autoranging for all measurement
THE COM4LAB COURSE ENTITLED
ranges “SYNCHRONOUS MACHINES” IS THE
 Digital Function Generator: SECOND COURSE TO THE FASCINATING
digitally generated sinusoidal, WORLD OF ELECTRICAL MACHINES. THE
triangular, square-wave signal types, USB-C Charger with a 45 W quick
PERFORMANCE OF THE SYNCHRONOUS
also DC charge function as a power supply for the
MACHINES, THE SPEED MEASUREMENT AND
Frequency range: 0.5 Hz – 100 kHz, COM4LAB Master Unit. An additional
THE SPEED ADJUSTMENT ARE EXAMINED.
also DC USB-A port with fast charge ensures
THE DESIGN, THE PRINCIPLE OF OPERATION
SYNC output: TTL clock parallel charging of one mobile device.
AND THE PERFORMANCE OF THE STEPPER
frequency 0.5 Hz – 100 kHz MOTOR ARE PRACTICALLY DEVISED USING A
Output voltage: max. ±10 V, (0 – 20 Technical data NUMBER OF EXPERIMENTS. THE COURSE
V) COMPRISES 9 CHAPTERS.
Output current: max. ±250 mA
 Digital 4-channel oscilloscope:  45 W PD, 15 V/3 A
TOTAL DURATION: UP TO 9 HOURS
4 differential inputs  USB-A Port DC 5 V/2,4 A
Sampling rate: 1 MS/s per channel  Overvoltage protection
Bandwidth: 200 kHz
Memory depth: 1KS per channel
 Overheat protection TARGET AUDIENCE
Resolution: 12 Bit per channel
Time ranges from 10 μs/div to 500 Scope of delivery
ms/div AMONG OTHERS, THE COURSE CAN BE
Voltage ranges from 10 mV/div to 10 USED TO SUPPORT THE TRAINING PROCESS
V/div  2 m USB-C/USB-C cable FOR THE FOLLOWING PROFESSIONS:
Trigger CH1 - CH4 and EXT
(referenced to ground), in 4095
steps, rising/falling edge
 ELECTRICAL SYSTEM FITTER

LD Didactic GmbH Technical Documentation Page 23

  ELECTRONICS TECHNICIAN FOR 70025-00 COM4LAB Board: 70025-30 COM4LAB Course:
MACHINE AND DRIVE TECHNOLOGY Electrical Machines Synchronous Machines

LEARNING
OBJECTIVES
THE STUDENTS ARE TO:

 BE ABLE TO RECOGNISE THE BASIC

PHYSICAL PRINCIPLES OF
SYNCHRONOUS MACHINES AND
 BE ABLE TO RECOGNISE THE DESIGN,
THE PRINCIPLE OF OPERATION AND
DIFFERENT OPERATING MODES OF THE
STEPPER MOTORS.

The experiment board to the COM4LAB The COM4LAB course Synchronous

courses Asynchronous Machines, Machines is the second course to the
TOPICS Synchronous Machines and DC fascinating world of electrical machines.
Machines (supplied separately). The performance of the synchronous
machines, the speed measurement and
THE COURSE COVERS THE FOLLOWING
the speed adjustment are examined. The
TOPICS: There are several function blocks on the
design, the principle of operation and the
experiment board, which are put into
performance of the stepper motor are
operation and also interconnected with
SYNCHRONOUS MACHINES practically devised using a number of
each other depending on the selected
experiments. The course comprises 9
experiment. The resulting circuits are
chapters.
 TERMINAL investigated in the course of the
corresponding experiments. The active
 ROTATIONAL DIRECTION
function blocks are indicated by a lit The course covers the following topics:
 STEPPER MODE green LED.
Synchronous machines
STAR CONNECTION – DELTA The experiment board, housed within a
CONNECTION sturdy board carrier, is to be used in
conjunction with, and powered by the  terminal
Master Unit (supplied separately).  rotational direction
 SPEED MEASUREMENT Circuits are wired by using 2 mm safety  stepper mode
 SPEED ADJUSTMENT WITH FREQUENCY cables (supplied separately).
CONVERTER
star connection – delta connection
Dimensions
STEPPER MOTOR
 speed measurement
 Circuit board: 280 × 200 mm2
 DESIGN  speed adjustment with frequency
 Frame: 296,5 × 354 mm2 converter
 PRINCIPLE OF OPERATION
 ROTATIONAL DIRECTION Supply voltage Stepper motor
 STEPPER MODE

 +15 V DC, −15 V DC und +5 V DC  design

FULL-STEP MODE – HALF-STEP MODE from the Master Unit
 principle of operation
 rotational direction
PREVIOUS Protective functions
 stepper mode

KNOWLEDGE  The use of safety cables avoids full-step mode – half-step mode
unintentional short-circuiting

THE STUDENTS NEED BASIC KNOWLEDGE IN The course …

THE AREAS OF DC AND AC TECHNOLOGY
AS WELL AS BASIC KNOWLEDGE OF
ELECTROMAGNETISM IN ORDER TO BE ABLE  can be displayed and filled out on
TO COMPLETE THE COURSE your own tablet/smartphone/laptop.
SUCCESSFULLY. THEY SHOULD BE FAMILIAR  is platform-independent - a current
WITH THE MEASUREMENT OF ELECTRICAL browser is sufficient.
QUANTITIES. IN ADDITION, DEALING WITH  can be distributed to students via QR
SIMPLE FORMULAS IS REQUIRED. codes.
 enables interactive experimenting:
The measured values from the
Master Unit are automatically made
available for evaluation in tables and
diagrams. The analysis and
documentation of the experiment on
the student device can be done at
school or at home.

LD Didactic GmbH Technical Documentation Page 24

  can be edited and thus adapted to Sampling rate: 1 MS/s per channel  Overvoltage protection
your own lesson plan. Bandwidth: 200 kHz
Memory depth: 1KS per channel  Overheat protection
Resolution: 12 Bit per channel
Perpetual course license. Time ranges from 10 μs/div to 500 Scope of delivery
ms/div
Technical data Voltage ranges from 10 mV/div to 10
V/div  2 m USB-C/USB-C cable
Trigger CH1 - CH4 and EXT
 Product key for activation of the (referenced to ground), in 4095
course licence via steps, rising/falling edge
https://register.leylab.de is  Digital analyzer: ALTERNATIVELY USB-C CHARGER
necessary. Later on the course can 8+1 digital signal inputs WITH UK-PLUG OR US-PLUG
be accessed and distributed from Input voltage TTL-compatible
LeyLab. Sampling frequency: 200 Hz – 2
 System requirements: MHz 70000-22 COM4LAB Set of Safety
- PC, tablet or smartphone with a Memory depth: 9 Bit x 2 K Leads, 2 mm, 24 pcs
current browser Triggering on any combination of the
- internet access input states

Additional properties

70000-00 COM4LAB Master Unit

 Voltage supply:
15 V/3 A
USB-C
 Interfaces:
WLAN
Ethernet 100 MBits RJ45
USB
 Extensions: Set of highly fexible test leads with
Extension Slot insulation in PVC with assembled
USB Interface (type A) stackable 2 mm multilam plugs with rigid
 NFC insulating sleeve on both ends.
The COM4LAB Master Unit is a
multifunctional, compact, measuring  Light strip & LEDs for status display
interface. As a universal base station it is  Security lock for mechanical  6 x 150 mm, red
used for the operation and power supply attachment and electronic activation  6 x 150 mm, black
for the COM4LAB experiment boards of the experiment boards  2 x 150 mm, blue
and as an independent measuring  Anti-theft protection (port for
laboratory. The Master Unit can be  4 x 300 mm, red
Kensington lock)
simultaneously connected to up to four  4 x 300 mm, black
digital terminal devices (PC, tablet or  2 x 300 mm, blue
smartphone) for the recording of Scope of delivery
measurements and for remote control of
its built-in functions. The Master Unit can Technical data
be quickly attached to an experiment  USB cable
board. Its clear and structured design  NFC card
results in easy operation.
 Rated voltage/current 600 V, CAT II /
10 A
 Lead cross section 0,5 mm²
Dimensions
ACCESSORIES

 295 x 154 × 30 mm3

70000-11 USB-C Charger 45 W ADDITIONALLY REQUIRED
Europlug (Type C)
Integrated measuring instruments
PC, TABLET OR SMARTPHONE WITH A
CURRENT BROWSER
 Two digital multimeters:
Voltage: DC/AC – 2 V | 20 V
Current: DC/AC – 20 mA | 200 mA | ME2.1.5 DC MACHINES
2A
Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2
MΩ
Autoranging for all measurement THE COM4LAB COURSE ENTITLED “DC
ranges MACHINES” IS THE THIRD COURSE TO THE
 Digital Function Generator: FASCINATING WORLD OF ELECTRICAL
digitally generated sinusoidal, MACHINES. THE PERFORMANCE OF THE DC
USB-C Charger with a 45 W quick
triangular, square-wave signal types, MACHINES FOR DIFFERENT CONNECTION
charge function as a power supply for the
also DC TYPES IS EXPLAINED AND PRACTICALLY
COM4LAB Master Unit. An additional
Frequency range: 0.5 Hz – 100 kHz, DEVISED USING A NUMBER OF
USB-A port with fast charge ensures EXPERIMENTS. THE COURSE COMPRISES 9
also DC
parallel charging of one mobile device. CHAPTERS.
SYNC output: TTL clock
frequency 0.5 Hz – 100 kHz
Output voltage: max. ±10 V, (0 – 20 Technical data TOTAL DURATION: UP TO 9 HOURS
V)
Output current: max. ±250 mA
 Digital 4-channel oscilloscope:  45 W PD, 15 V/3 A
4 differential inputs  USB-A Port DC 5 V/2,4 A TARGET AUDIENCE
LD Didactic GmbH Technical Documentation Page 25
 AMONG OTHERS, THE COURSE CAN BE 70025-00 COM4LAB Board: 70025-40 COM4LAB Course: DC
USED TO SUPPORT THE TRAINING PROCESS
Electrical Machines Machines
FOR THE FOLLOWING PROFESSIONS:

 ELECTRICAL SYSTEM FITTER

 ELECTRONICS TECHNICIAN FOR
MACHINE AND DRIVE TECHNOLOGY

LEARNING
OBJECTIVES
THE STUDENTS ARE TO:

 BE ABLE TO RECOGNISE THE BASIC

PHYSICAL PRINCIPLES OF DC
MACHINES AND The experiment board to the COM4LAB The COM4LAB course DC Machines is
 MASTER DIFFERENT CONNECTION courses Asynchronous Machines, the third course to the fascinating world
TYPES FOR DC MACHINES. Synchronous Machines and DC of electrical machines. The performance
Machines (supplied separately). of the DC machines for different
connection types is explained and
TOPICS There are several function blocks on the
experiment board, which are put into
practically devised using a number of
experiments. The course comprises 9
chapters.
operation and also interconnected with
THE COURSE COVERS THE FOLLOWING each other depending on the selected
TOPICS: experiment. The resulting circuits are The course covers the following topics:
investigated in the course of the
corresponding experiments. The active
 DESIGN
function blocks are indicated by a lit  design
 CIRCUIT DIAGRAMS green LED.  circuit diagrams

BLOCK CIRCUIT DIAGRAM – EQIVALENT The experiment board, housed within a block circuit diagram – eqivalent
CIRCUIT DIAGRAM sturdy board carrier, is to be used in circuit diagram
conjunction with, and powered by the
Master Unit (supplied separately).
 CONNECTION TYPES Circuits are wired by using 2 mm safety  connection types
cables (supplied separately).
EXTERNAL EXCITATION – SHUNT external excitation – shunt winding –
WINDING – SERIES WINDING – Dimensions series winding – generator operation
GENERATOR OPERATION

 Circuit board: 280 × 200 mm2 The course …

PREVIOUS  Frame: 296,5 × 354 mm2

 can be displayed and filled out on
KNOWLEDGE Supply voltage your own tablet/smartphone/laptop.
 is platform-independent - a current
browser is sufficient.
THE STUDENTS NEED BASIC KNOWLEDGE IN  +15 V DC, −15 V DC und +5 V DC
THE AREAS OF DC AND AC TECHNOLOGY
 can be distributed to students via QR
from the Master Unit codes.
AS WELL AS BASIC KNOWLEDGE OF
ELECTROMAGNETISM IN ORDER TO BE ABLE  enables interactive experimenting:
TO COMPLETE THE COURSE Protective functions The measured values from the
SUCCESSFULLY. THEY SHOULD BE FAMILIAR Master Unit are automatically made
WITH THE MEASUREMENT OF ELECTRICAL available for evaluation in tables and
QUANTITIES. IN ADDITION, DEALING WITH
 The use of safety cables avoids diagrams. The analysis and
unintentional short-circuiting documentation of the experiment on
SIMPLE FORMULAS IS REQUIRED.
the student device can be done at
school or at home.
 can be edited and thus adapted to
your own lesson plan.

Perpetual course license.

Technical data

 Product key for activation of the

course licence via
https://register.leylab.de is
necessary. Later on the course can
be accessed and distributed from
LeyLab.

LD Didactic GmbH Technical Documentation Page 26

  System requirements: Sampling frequency: 200 Hz – 2
- PC, tablet or smartphone with a MHz
Memory depth: 9 Bit x 2 K 70000-22 COM4LAB Set of Safety
current browser
- internet access Triggering on any combination of the Leads, 2 mm, 24 pcs
input states

Additional properties
70000-00 COM4LAB Master Unit
 Voltage supply:
15 V/3 A
USB-C
 Interfaces:
WLAN
Ethernet 100 MBits RJ45
USB
 Extensions:
Extension Slot Set of highly fexible test leads with
USB Interface (type A) insulation in PVC with assembled
The COM4LAB Master Unit is a stackable 2 mm multilam plugs with rigid
 NFC
insulating sleeve on both ends.
multifunctional, compact, measuring
interface. As a universal base station it is
 Light strip & LEDs for status display
used for the operation and power supply  Security lock for mechanical
for the COM4LAB experiment boards attachment and electronic activation  6 x 150 mm, red
and as an independent measuring of the experiment boards  6 x 150 mm, black
laboratory. The Master Unit can be  Anti-theft protection (port for  2 x 150 mm, blue
simultaneously connected to up to four Kensington lock)  4 x 300 mm, red
digital terminal devices (PC, tablet or
smartphone) for the recording of  4 x 300 mm, black
measurements and for remote control of Scope of delivery  2 x 300 mm, blue
its built-in functions. The Master Unit can
be quickly attached to an experiment
 USB cable Technical data
board. Its clear and structured design
results in easy operation.  NFC card
 Rated voltage/current 600 V, CAT II /
Dimensions 10 A
ACCESSORIES  Lead cross section 0,5 mm²
3
 295 x 154 × 30 mm
70000-11 USB-C Charger 45 W
Integrated measuring instruments Europlug (Type C) ADDITIONALLY REQUIRED

 Two digital multimeters: PC, TABLET OR SMARTPHONE WITH A

Voltage: DC/AC – 2 V | 20 V CURRENT BROWSER
Current: DC/AC – 20 mA | 200 mA |
2A
Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2 ME2.2.1 POWER ELECTRONICS
MΩ
Autoranging for all measurement
ranges
 Digital Function Generator: THE COURSES ON POWER ELECTRONICS
CONVEY THE TOPIC IN CONCENTRATED
digitally generated sinusoidal,
FORM TO DEEPEN UNDERSTANDING.
triangular, square-wave signal types, USB-C Charger with a 45 W quick
also DC CHARACTERISTICS OF POWER
charge function as a power supply for the SEMICONDUCTORS AND THE BASIC
Frequency range: 0.5 Hz – 100 kHz, COM4LAB Master Unit. An additional STANDARD CIRCUITS ARE INVESTIGATED.
also DC USB-A port with fast charge ensures
SYNC output: TTL clock ALL THE EXPERIMENTS WORK WITH SINGLE-
parallel charging of one mobile device. PHASE SAFETY EXTRA-LOW VOLTAGE,
frequency 0.5 Hz – 100 kHz
WHICH IS NON-HAZARDOUS. ONLY SMALL
Output voltage: max. ±10 V, (0 – 20
Technical data AMOUNTS OF MATERIALS AND LITTLE SPACE
V)
Output current: max. ±250 mA ARE NEEDED FOR THE EXPERIMENTS.

 Digital 4-channel oscilloscope:  45 W PD, 15 V/3 A

4 differential inputs
Sampling rate: 1 MS/s per channel  USB-A Port DC 5 V/2,4 A LEARNING OBJECTIVES
Bandwidth: 200 kHz  Overvoltage protection
Memory depth: 1KS per channel  Overheat protection  BASIC PHYSICAL PRINCIPLES OF POWER
Resolution: 12 Bit per channel SEMICONDUCTORS
Time ranges from 10 μs/div to 500
ms/div Scope of delivery  DESIGN OF KEY BASIC CIRCUITS FOR
Voltage ranges from 10 mV/div to 10 POWER ELECTRONICS
V/div  ASSESSMENT OF PROPERTIES OF
Trigger CH1 - CH4 and EXT
 2 m USB-C/USB-C cable RECTIFIERS AND CONVERTERS
(referenced to ground), in 4095
steps, rising/falling edge
 Digital analyzer: TOPICS
8+1 digital signal inputs
ALTERNATIVELY USB-C CHARGER
Input voltage TTL-compatible WITH UK-PLUG OR US-PLUG

LD Didactic GmbH Technical Documentation Page 27

 THE COURSES COVER THE FOLLOWING Virtual Laboratory: 70022 COM3LAB Course: Power
TOPICS:
Electronics II - COM4LAB
 Oscilloscope ready
 SEMICONDUCTORS IN POWER  Function generator
ELECTRONICS
 Multimeter (x2)
 WIRING AND CONTROL
 Digital analyser
 SWITCHING PROCESSES AND
 Characteristics curve plotter
COMMUTATION
 UNCONTROLLED RECTIFIER CIRCUITS
 Converter analyser

 CHARACTERISTIC VALUES FOR

 Converter control unit
PERIODIC SIGNALS
 CONTROLLED LINE-COMMUTATED Additional Functions:
CONVERTERS
 CIRCUITS: M1C, M3C, B2C, B6C  Word Processing
Supplementary course on power
 SEMI-CONTROLLED RECTIFIERS  Printer inverters, controllers, converters and
 SELF-COMMUTATED CONVERTERS  Calculator drive technology, consisting of a dongle
 SEMICONDUCTOR SWITCHES AND  Free Experimentation for the PE I experiment board, a circuit
CHOPPERS board with the equivalent circuit of a
 Glossary three-phase asynchronous machine
 SWITCHES AND ACTUATORS FOR DC
including a rotating field indicator.
 INVERTERS
The experiment board is located in a
 STATIC CONVERTERS FOR CLOSED- stable course frame. The Master Unit
LOOP CONTROL
Curriculum Coverage
(700020, sold separately) is slid onto the
 STATIC CONVERTERS FOR DRIVE course frame and connected to the
TECHNOLOGY board. The Security Lock ensures secure  Self-commutated converters
communication. (inverters)
 Semiconductor switches and
The experiment board is powered and controllers (bi-directional static
triggered by the Master Unit. The converters)
7002101 COM3LAB Course: experiments are wired using 2 mm safety  Switches and controllers for DC
Power Electronics I - cables (700022, sold separately).  Converters
COM4LAB ready  Power converters in automatic
Course content, experiment instructions control technology
and tasks are taught via a course-
 Power converters in drive technology
specific software.

Virtual Laboratory
The COM3LAB software contains
courses in all supported languages and
the current version can be downloaded  Oscilloscope
for free at www.ld-didactic.de.
Alternatively, the COM3LAB software
 Function generator
can also be obtained on DVD  Multimeter (x2)
(70000CBT).  Digital analyser
 Characteristics curve plotter
 Power converter analyser
 Power converter control unit

Technical Data: Additional Functions

Course on line-commutated and self-
commutated converter connections,  1 three-phase network generator in
consisting of an experiment board with  Word Processing
50 and 60 Hz
various circuits for inclusion in the Master  Printer
Unit.
 Self-commutated and line-
commutated static converter (E1 to  Calculator
B6 circuit) with TSE protection  Free Experimentation
Topics:  H6-MOSFET frequency converter  Glossary
from 1 to 120 Hz
 Introduction  Three independent amperemeters
 Semiconductors in power electronics  Three incandescent lamps as ohmic
load
 Wiring and triggering The dongle is plugged into the Power
 Inductive and capacitive loads Electronics I experiment board (7002101,
 Switching processes and
commutation  4-channel multiplexer sold separately). This is operated with
the Master Unit (700020, sold
 Uncontrolled rectifier circuits separately).
 Characteristics of periodic signals
 Controlled line-commutated The experiments are wired with 2 mm
converters safety cables (700022, sold separately).
 M1C circuit
 M3C circuit Course content, experiment instructions
 B2C circuit and assignments are taught via course-
 B6C circuit specific software.
 Semi-controlled rectifiers
LD Didactic GmbH Technical Documentation Page 28
 The COM3LAB software contains  Status display (successfully Bandwidth: 200 kHz
courses in all supported languages and processed, not processed) Memory depth: 1KS per channel
the current version can be downloaded Resolution: 12 Bit per channel
from www.ld-didactic.de for free.
 Evaluation of measurements and
Time ranges from 10 μs/div to 500
tasks
Alternatively, the COM3LAB software ms/div
can also be obtained on DVD  Evaluation of the circuitry Voltage ranges from 10 mV/div to 10
(70000CBT). V/div
Trigger CH1 - CH4 and EXT
(referenced to ground), in 4095
steps, rising/falling edge
70000CBT DVD: COM3LAB Additionally required:  Digital analyzer:
Software 8+1 digital signal inputs
Alternatively, the software Input voltage TTL-compatible
Sampling frequency: 200 Hz – 2
can be downloaded free of MHz
charge at SOFTWARE Memory depth: 9 Bit x 2 K
Triggering on any combination of the
DOWNLOAD and is updated input states
regularly.
Additional properties
70000-00 COM4LAB Master Unit
 Voltage supply:
15 V/3 A
USB-C

COM3LAB software package for Master  Interfaces:

WLAN
Unit 2.0 (700020) and 70000USB
Ethernet 100 MBits RJ45
USB
DVD contains:  Extensions:
Extension Slot
USB Interface (type A)
 All available COM3LAB courses in all
available languages The COM4LAB Master Unit is a  NFC
multifunctional, compact, measuring  Light strip & LEDs for status display
 COM3LAB starter software
interface. As a universal base station it is
 COM3LAB configurator used for the operation and power supply
 Security lock for mechanical
attachment and electronic activation
 USB driver software for Master Unit for the COM4LAB experiment boards
of the experiment boards
2.0 and as an independent measuring
 .NET 4.0 laboratory. The Master Unit can be  Anti-theft protection (port for
simultaneously connected to up to four Kensington lock)
 Separate installation for the audio digital terminal devices (PC, tablet or
package in all available languages smartphone) for the recording of Scope of delivery
measurements and for remote control of
For each COM3LAB multimedia course its built-in functions. The Master Unit can
there is an electronic, interactive be quickly attached to an experiment  USB cable
instruction manual. The contents of the board. Its clear and structured design
 NFC card
manual are dependent on the topic and results in easy operation.
are tailored to the hardware. The
operation and function of the manuals
Dimensions
are identical for all courses. The 32-bit
user interface, into which the interactive
ACCESSORIES
manual, the virtual lab and the tools are  295 x 154 × 30 mm3
integrated, also remains the same for all 70000-11 USB-C Charger 45 W
courses. Structure of multimedia course
software: Integrated measuring instruments Europlug (Type C)

 Electronic manual  Two digital multimeters:

Voltage: DC/AC – 2 V | 20 V
 The same look and the same
Current: DC/AC – 20 mA | 200 mA |
operation for all courses
2A
 Quick and easy installation Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2
 Virtual lab (oscilloscope, multimeters, MΩ
function generator etc.) Autoranging for all measurement
 Tools (printers, calculators, word ranges
processing, copy function for  Digital Function Generator:
measurement results) digitally generated sinusoidal,
 Help triangular, square-wave signal types, USB-C Charger with a 45 W quick
also DC charge function as a power supply for the
 Glossary Frequency range: 0.5 Hz – 100 kHz, COM4LAB Master Unit. An additional
 Table of contents also DC USB-A port with fast charge ensures
 Language (English, French, etc.) can SYNC output: TTL clock parallel charging of one mobile device.
be switched by pressing a button frequency 0.5 Hz – 100 kHz
Output voltage: max. ±10 V, (0 – 20
 Readings and texts can be used in
V) Technical data
your own documents
Output current: max. ±250 mA
 Zoomable
 Digital 4-channel oscilloscope:  45 W PD, 15 V/3 A
 Free selectable chapters 4 differential inputs  USB-A Port DC 5 V/2,4 A
Sampling rate: 1 MS/s per channel

LD Didactic GmbH Technical Documentation Page 29

  Overvoltage protection
 Overheat protection

Scope of delivery

 2 m USB-C/USB-C cable

ALTERNATIVELY USB-C CHARGER

WITH UK-PLUG OR US-PLUG

70000-22 COM4LAB Set of Safety

Leads, 2 mm, 24 pcs

Set of highly fexible test leads with

insulation in PVC with assembled
stackable 2 mm multilam plugs with rigid
insulating sleeve on both ends.

 6 x 150 mm, red

 6 x 150 mm, black
 2 x 150 mm, blue
 4 x 300 mm, red
 4 x 300 mm, black
 2 x 300 mm, blue

Technical data

 Rated voltage/current 600 V, CAT II /

10 A
 Lead cross section 0,5 mm²

ADDITIONALLY REQUIRED

PC WITH WINDOWS 7/8/10 64 BIT

EDITION AND ONE FREE USB
INTERFACE

LD Didactic GmbH Technical Documentation Page 30

ME3.1.1 PHOTOVOLTAICS for the COM4LAB experiment boards  Security lock for mechanical
and as an independent measuring attachment and electronic activation
laboratory. The Master Unit can be of the experiment boards
simultaneously connected to up to four
digital terminal devices (PC, tablet or
 Anti-theft protection (port for
THE PHOTOVOLTAICS COURSE IS A Kensington lock)
FOUNDATION COURSE ON USING SOLAR smartphone) for the recording of
CELLS. IT DEALS WITH THE STRUCTURE AND measurements and for remote control of
THE FUNCTION OF SOLAR CELLS. USING its built-in functions. The Master Unit can Scope of delivery
SEVERAL EXPERIMENTS, THE FUNCTION OF be quickly attached to an experiment
SOLAR MODULES IN DIFFERENT CONDITIONS board. Its clear and structured design
IS EXAMINED. WITH ANIMATIONS AND results in easy operation.  USB cable
SEVERAL ILLUSTRATIONS, THIS COURSE  NFC card
GIVES A CLEAR INTRODUCTION TO THE Dimensions
WORLD OF PHOTOVOLTAIC SYSTEMS.

 295 x 154 × 30 mm3 ACCESSORIES

LEARNING OBJECTIVES
Integrated measuring instruments 70000-11 USB-C Charger 45 W
 FUNCTION AND APPLICATION OF A Europlug (Type C)
SOLAR COLLECTOR  Two digital multimeters:
Voltage: DC/AC – 2 V | 20 V
Current: DC/AC – 20 mA | 200 mA |
TOPICS 2A
Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2
THE COURSE COVERS THE FOLLOWING MΩ
TOPICS:
Autoranging for all measurement
ranges
 Digital Function Generator:
 SOLAR CELLS (FEATURES, FUNCTION, digitally generated sinusoidal,
ETC.) triangular, square-wave signal types,
 SOLAR MODULE (FEATURES, FUNCTION, also DC
ETC.) Frequency range: 0.5 Hz – 100 kHz, USB-C Charger with a 45 W quick
also DC charge function as a power supply for the
 CIRCUIT TYPES OF SOLAR MODULES
SYNC output: TTL clock COM4LAB Master Unit. An additional
 SOLAR CHARACTERISTICS frequency 0.5 Hz – 100 kHz USB-A port with fast charge ensures
 INFLUENCE OF TEMPERATURE Output voltage: max. ±10 V, (0 – 20 parallel charging of one mobile device.
 INFLUENCE OF SHADES V)
Output current: max. ±250 mA Technical data
 CHARGING CIRCUIT
 Digital 4-channel oscilloscope:
 SOLAR CHARGE CONTROLLER
4 differential inputs
 PHOTOVOLTAICS SYSTEM Sampling rate: 1 MS/s per channel  45 W PD, 15 V/3 A
 APPLICATIONS Bandwidth: 200 kHz  USB-A Port DC 5 V/2,4 A
Memory depth: 1KS per channel  Overvoltage protection
Resolution: 12 Bit per channel
Time ranges from 10 μs/div to 500  Overheat protection
ms/div
Voltage ranges from 10 mV/div to 10 Scope of delivery
70053-00 COM4LAB Board: V/div
Photovoltaics Trigger CH1 - CH4 and EXT
(referenced to ground), in 4095  2 m USB-C/USB-C cable
steps, rising/falling edge
ALTERNATIVELY PHOTOVOLTAICS  Digital analyzer:
8+1 digital signal inputs
ACCESSORIES FOR 115 V MAINS Input voltage TTL-compatible ALTERNATIVELY USB-C CHARGER
VOLTAGE Sampling frequency: 200 Hz – 2 WITH UK-PLUG OR US-PLUG
MHz
Memory depth: 9 Bit x 2 K
70053-20 COM4LAB Course: Triggering on any combination of the 70000-22 COM4LAB Set of Safety
Photovoltaics input states Leads, 2 mm, 24 pcs

Additional properties
70000-00 COM4LAB Master Unit
 Voltage supply:
15 V/3 A
USB-C
 Interfaces:
WLAN
Ethernet 100 MBits RJ45
USB
 Extensions:
Extension Slot
USB Interface (type A) Set of highly fexible test leads with
The COM4LAB Master Unit is a  NFC insulation in PVC with assembled
multifunctional, compact, measuring stackable 2 mm multilam plugs with rigid
interface. As a universal base station it is
 Light strip & LEDs for status display
insulating sleeve on both ends.
used for the operation and power supply

LD Didactic GmbH Technical Documentation Page 31

  6 x 150 mm, red
 6 x 150 mm, black
 2 x 150 mm, blue
 4 x 300 mm, red
 4 x 300 mm, black
 2 x 300 mm, blue

Technical data

 Rated voltage/current 600 V, CAT II /

10 A
 Lead cross section 0,5 mm²

ADDITIONALLY REQUIRED

PC, TABLET OR SMARTPHONE WITH A

CURRENT BROWSER

LD Didactic GmbH Technical Documentation Page 32

 THE COM4LAB TRAINING SYSTEM IS  LOCAL OSCILLATORS  The use of safety cables avoids
IDEALLY SUITED FOR TRAINING IN THE unintentional short-circuiting.
FIELDS OF ELECTRICAL ENGINEERING,
 DIRECTIONAL COUPLER

TELECOMMUNICATIONS OR  ANTENNAS  The use of a mask protects the

electronics from mechanical and
COMMUNICATIONS ENGINEERING. IT OFFERS  SELF-CLOCKING SIGNAL WITH COSTA
electrical damage, e.g. by ESD
A PRACTICAL AND INTERACTIVE LEARNING LOOP
discharge.
ENVIRONMENT IN WHICH PARTICIPANTS CAN
DIRECTLY APPLY AND DEEPEN THEIR  The use of a metal frame shields
KNOWLEDGE. THANKS TO THE HIGH- electromagnetic fields and cools the
QUALITY COMPONENTS AND MEASURING electronics.
DEVICES, AN EXACT ANALYSIS OF THE
RESULTS IS POSSIBLE. THE TRAINING
ME5.1.1 COMPONENTS AND AM, FM,
Scope of delivery
SYSTEM IS EASY TO USE AND CAN BE USED PSK
BY BOTH BEGINNERS AND ADVANCED
USERS. WITH THIS PRODUCT YOU ACQUIRE In addition to the experiment board itself,
AN EFFECTIVE TOOL FOR SUCCESSFUL
70071-00 COM4LAB Board: the scope of delivery includes:
TRAINING IN THE FIELD OF RADIO Reception and Transmission
TECHNOLOGY, SO THAT YOU CAN CARRY Technology
OUT A VARIETY OF EXPERIMENTS WITH A  mask
REALISTIC AND LICENSE-FREE RADIO LINK.  antenna set
 probe adapter 10:1 with a set of
probes
TARGET AUDIENCE  2 x HF-cable, BNC-BNC, 1.5 m

AMONG OTHERS, THE COURSE CAN BE

USED TO SUPPORT THE TRAINING PROCESS
FOR THE FOLLOWING PROFESSIONS: 70071-20 COM4LAB Course:
RxTx 1 - Analogue
 RADIO ELECTRONICS TECHNICIAN Transmission Techniques AM,
 RADAR ELECTRONICS TECHNICIAN FM and PSK
 BASIC STUDIES IN ELECTRICAL
ENGINEERING, COMMUNICATIONS The experiment board to the COM4LAB
ENGINEERING OR COMMUNICATION courses Analogue Transmission 70072-00 COM4LAB Extension
TECHNOLOGY Techniques AM, FM and PSK, Digital Board: Band-Scanner
Modulations QPSK and QAM, Digital
Communication und Bi- and
MEASURING Omnidirectional Communication
(supplied separately).
TECHNOLOGY
There are several function blocks on the
 POWER MEASUREMENT experiment board, which are put into
 SIGNAL ANALYSIS WITH THE operation and also interconnected with
OSCILLOSCOPE each other depending on the selected
experiment. The resulting circuits are
 EYE DIAGRAMS
investigated in the course of the
 CONSTELLATION DIAGRAMMS X-Y corresponding experiments.
REPRESENTATION
 SPECTRAL ANALYSIS OF SIGNALS AND
70000-00 COM4LAB Master Unit
A metal frame is screwed onto the
MIXED PRODUCTS
experiment board. It serves to shield
 BIT ERROR RATE MEASUREMENT electromagnetic fields between the
 MEASURING WITH PROBES individual function blocks and as a heat
sink.

HIGH FREQUENCY The experiment board, housed within a

sturdy board carrier, is to be used in
TECHNOLOGY conjunction with, and powered by the
Master Unit (supplied separately).
 SUPERHETERODYNE ARCHITECTURE
Circuits are wired by using BNC-BNC
cables and 2 mm safety cables The COM4LAB Master Unit is a
 BASEBAND
(supplied separately). multifunctional, compact, measuring
 10.7 MHZ INTERMEDIATE FREQUENCY interface. As a universal base station it is
 100 MHZ HIGH FREQUENCY BAND used for the operation and power supply
Dimensions for the COM4LAB experiment boards
 <40 NW TRANSMIT POWER
and as an independent measuring
 ANTENNA ADJUSTMENT laboratory. The Master Unit can be
 Circuit board: 280 × 200 mm2
 NOISE, MIXED PRODUCTS AND simultaneously connected to up to four
 Frame: 296,5 × 354 mm2 digital terminal devices (PC, tablet or
INTERFERENCE
smartphone) for the recording of
Supply voltage measurements and for remote control of
COMPONENTS its built-in functions. The Master Unit can
be quickly attached to an experiment
 +15 V DC, −15 V DC und +5 V DC board. Its clear and structured design
 AMPLIFIER from the Master Unit results in easy operation.
 ATTENUATORS
 FREQUENCY MIXER Protective functions Dimensions
 QUADRATURE MIXER

LD Didactic GmbH Technical Documentation Page 33

  295 x 154 × 30 mm3
70000-11 USB-C Charger 45 W ADDITIONALLY REQUIRED
Integrated measuring instruments Europlug (Type C)
PC, TABLET OR SMARTPHONE WITH A
 Two digital multimeters: CURRENT BROWSER
Voltage: DC/AC – 2 V | 20 V
Current: DC/AC – 20 mA | 200 mA |
2A AUDIO ADAPTER 3,5 MM JACK FOR
Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2 AUDIO PLAYERS SUCH AS MP3
MΩ PLAYER, TABLET OR PC
Autoranging for all measurement
ranges
 Digital Function Generator: AUDIO PLAYER WITH DIFFERENT AUDIO
digitally generated sinusoidal, FILES
triangular, square-wave signal types,
USB-C Charger with a 45 W quick
also DC
charge function as a power supply for the ME5.1.2 DIGITAL MODULATIONS
Frequency range: 0.5 Hz – 100 kHz, COM4LAB Master Unit. An additional
also DC
USB-A port with fast charge ensures QPSK AND QAM
SYNC output: TTL clock
parallel charging of one mobile device.
frequency 0.5 Hz – 100 kHz
Output voltage: max. ±10 V, (0 – 20 70071-00 COM4LAB Board:
V) Technical data Reception and Transmission
Output current: max. ±250 mA Technology
 Digital 4-channel oscilloscope:
 45 W PD, 15 V/3 A
4 differential inputs
Sampling rate: 1 MS/s per channel  USB-A Port DC 5 V/2,4 A
Bandwidth: 200 kHz  Overvoltage protection
Memory depth: 1KS per channel  Overheat protection
Resolution: 12 Bit per channel
Time ranges from 10 μs/div to 500
ms/div Scope of delivery
Voltage ranges from 10 mV/div to 10
V/div
Trigger CH1 - CH4 and EXT  2 m USB-C/USB-C cable
(referenced to ground), in 4095
steps, rising/falling edge
 Digital analyzer:
8+1 digital signal inputs ALTERNATIVELY USB-C CHARGER
Input voltage TTL-compatible WITH UK-PLUG OR US-PLUG The experiment board to the COM4LAB
Sampling frequency: 200 Hz – 2 courses Analogue Transmission
MHz Techniques AM, FM and PSK, Digital
Memory depth: 9 Bit x 2 K 70000-22 COM4LAB Set of Safety Modulations QPSK and QAM, Digital
Triggering on any combination of the Leads, 2 mm, 24 pcs Communication und Bi- and
input states Omnidirectional Communication
(supplied separately).
Additional properties
There are several function blocks on the
experiment board, which are put into
 Voltage supply: operation and also interconnected with
15 V/3 A each other depending on the selected
USB-C experiment. The resulting circuits are
 Interfaces: investigated in the course of the
WLAN corresponding experiments.
Ethernet 100 MBits RJ45
USB A metal frame is screwed onto the
 Extensions: experiment board. It serves to shield
Extension Slot Set of highly fexible test leads with
electromagnetic fields between the
USB Interface (type A) insulation in PVC with assembled
individual function blocks and as a heat
stackable 2 mm multilam plugs with rigid
 NFC sink.
insulating sleeve on both ends.
 Light strip & LEDs for status display
 Security lock for mechanical The experiment board, housed within a
attachment and electronic activation  6 x 150 mm, red sturdy board carrier, is to be used in
of the experiment boards  6 x 150 mm, black conjunction with, and powered by the
 2 x 150 mm, blue Master Unit (supplied separately).
 Anti-theft protection (port for
Circuits are wired by using BNC-BNC
Kensington lock)  4 x 300 mm, red cables and 2 mm safety cables
 4 x 300 mm, black (supplied separately).
Scope of delivery  2 x 300 mm, blue
Dimensions
 USB cable Technical data
 NFC card  Circuit board: 280 × 200 mm2
 Rated voltage/current 600 V, CAT II /  Frame: 296,5 × 354 mm2
10 A

ACCESSORIES  Lead cross section 0,5 mm² Supply voltage

LD Didactic GmbH Technical Documentation Page 34

  +15 V DC, −15 V DC und +5 V DC board. Its clear and structured design  NFC card
from the Master Unit results in easy operation.

Protective functions Dimensions

ACCESSORIES
 The use of safety cables avoids  295 x 154 × 30 mm3
unintentional short-circuiting. 70000-11 USB-C Charger 45 W
 The use of a mask protects the Integrated measuring instruments Europlug (Type C)
electronics from mechanical and
electrical damage, e.g. by ESD
discharge.  Two digital multimeters:
Voltage: DC/AC – 2 V | 20 V
 The use of a metal frame shields
Current: DC/AC – 20 mA | 200 mA |
electromagnetic fields and cools the
2A
electronics.
Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2
MΩ
Scope of delivery Autoranging for all measurement
ranges
In addition to the experiment board itself,  Digital Function Generator:
the scope of delivery includes: digitally generated sinusoidal,
triangular, square-wave signal types, USB-C Charger with a 45 W quick
also DC charge function as a power supply for the
 mask Frequency range: 0.5 Hz – 100 kHz, COM4LAB Master Unit. An additional
also DC USB-A port with fast charge ensures
 antenna set
SYNC output: TTL clock parallel charging of one mobile device.
 probe adapter 10:1 with a set of frequency 0.5 Hz – 100 kHz
probes Output voltage: max. ±10 V, (0 – 20
Technical data
 2 x HF-cable, BNC-BNC, 1.5 m V)
Output current: max. ±250 mA
 Digital 4-channel oscilloscope:  45 W PD, 15 V/3 A
4 differential inputs  USB-A Port DC 5 V/2,4 A
70071-30 COM4LAB Course: Sampling rate: 1 MS/s per channel
 Overvoltage protection
RxTx 2 - Digital Modulations Bandwidth: 200 kHz
QPSK and QAM Memory depth: 1KS per channel  Overheat protection
Resolution: 12 Bit per channel
Time ranges from 10 μs/div to 500 Scope of delivery
ms/div
70072-00 COM4LAB Extension Voltage ranges from 10 mV/div to 10
Board: Band-Scanner V/div  2 m USB-C/USB-C cable
Trigger CH1 - CH4 and EXT
(referenced to ground), in 4095
steps, rising/falling edge
 Digital analyzer: ALTERNATIVELY USB-C CHARGER
8+1 digital signal inputs WITH UK-PLUG OR US-PLUG
Input voltage TTL-compatible
Sampling frequency: 200 Hz – 2
MHz 70000-22 COM4LAB Set of Safety
Memory depth: 9 Bit x 2 K Leads, 2 mm, 24 pcs
Triggering on any combination of the
input states

70000-00 COM4LAB Master Unit Additional properties

 Voltage supply:
15 V/3 A
USB-C
 Interfaces:
WLAN
Ethernet 100 MBits RJ45
USB
 Extensions: Set of highly fexible test leads with
Extension Slot insulation in PVC with assembled
USB Interface (type A) stackable 2 mm multilam plugs with rigid
The COM4LAB Master Unit is a
multifunctional, compact, measuring  NFC insulating sleeve on both ends.
interface. As a universal base station it is  Light strip & LEDs for status display
used for the operation and power supply  Security lock for mechanical
for the COM4LAB experiment boards
 6 x 150 mm, red
attachment and electronic activation  6 x 150 mm, black
and as an independent measuring of the experiment boards
laboratory. The Master Unit can be  2 x 150 mm, blue
simultaneously connected to up to four  Anti-theft protection (port for
Kensington lock)  4 x 300 mm, red
digital terminal devices (PC, tablet or
smartphone) for the recording of  4 x 300 mm, black
measurements and for remote control of Scope of delivery  2 x 300 mm, blue
its built-in functions. The Master Unit can
be quickly attached to an experiment Technical data
 USB cable
LD Didactic GmbH Technical Documentation Page 35
  Rated voltage/current 600 V, CAT II /  Frame: 296,5 × 354 mm2 smartphone) for the recording of
10 A measurements and for remote control of
its built-in functions. The Master Unit can
 Lead cross section 0,5 mm² Supply voltage be quickly attached to an experiment
board. Its clear and structured design
results in easy operation.
 +15 V DC, −15 V DC und +5 V DC
ADDITIONALLY REQUIRED from the Master Unit
Dimensions

PC, TABLET OR SMARTPHONE WITH A Protective functions

 295 x 154 × 30 mm3
CURRENT BROWSER
 The use of safety cables avoids
unintentional short-circuiting. Integrated measuring instruments
AUDIO ADAPTER 3,5 MM JACK FOR
 The use of a mask protects the
AUDIO PLAYERS SUCH AS MP3 electronics from mechanical and
PLAYER, TABLET OR PC electrical damage, e.g. by ESD
 Two digital multimeters:
Voltage: DC/AC – 2 V | 20 V
discharge.
Current: DC/AC – 20 mA | 200 mA |
AUDIO PLAYER WITH DIFFERENT AUDIO  The use of a metal frame shields 2A
electromagnetic fields and cools the Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2
FILES
electronics. MΩ
Autoranging for all measurement
ME5.1.3 DIGITAL COMMUNICATION Scope of delivery ranges
 Digital Function Generator:
digitally generated sinusoidal,
70071-00 COM4LAB Board: In addition to the experiment board itself, triangular, square-wave signal types,
Reception and Transmission the scope of delivery includes: also DC
Technology Frequency range: 0.5 Hz – 100 kHz,
 mask also DC
SYNC output: TTL clock
 antenna set frequency 0.5 Hz – 100 kHz
 probe adapter 10:1 with a set of Output voltage: max. ±10 V, (0 – 20
probes V)
 2 x HF-cable, BNC-BNC, 1.5 m Output current: max. ±250 mA
 Digital 4-channel oscilloscope:
4 differential inputs
Sampling rate: 1 MS/s per channel
70071-40 COM4LAB Course: Bandwidth: 200 kHz
RxTx 3 - Digital Memory depth: 1KS per channel
Resolution: 12 Bit per channel
Communication Time ranges from 10 μs/div to 500
ms/div
Voltage ranges from 10 mV/div to 10
The experiment board to the COM4LAB V/div
courses Analogue Transmission
70072-00 COM4LAB Extension
Trigger CH1 - CH4 and EXT
Techniques AM, FM and PSK, Digital Board: Band-Scanner (referenced to ground), in 4095
Modulations QPSK and QAM, Digital steps, rising/falling edge
Communication und Bi- and  Digital analyzer:
Omnidirectional Communication 8+1 digital signal inputs
(supplied separately). Input voltage TTL-compatible
Sampling frequency: 200 Hz – 2
There are several function blocks on the MHz
experiment board, which are put into Memory depth: 9 Bit x 2 K
operation and also interconnected with Triggering on any combination of the
each other depending on the selected input states
experiment. The resulting circuits are
investigated in the course of the Additional properties
corresponding experiments.
70000-00 COM4LAB Master Unit
A metal frame is screwed onto the  Voltage supply:
experiment board. It serves to shield 15 V/3 A
electromagnetic fields between the USB-C
individual function blocks and as a heat  Interfaces:
sink. WLAN
Ethernet 100 MBits RJ45
USB
The experiment board, housed within a
sturdy board carrier, is to be used in  Extensions:
conjunction with, and powered by the Extension Slot
Master Unit (supplied separately). USB Interface (type A)
Circuits are wired by using BNC-BNC The COM4LAB Master Unit is a
 NFC
cables and 2 mm safety cables multifunctional, compact, measuring  Light strip & LEDs for status display
(supplied separately). interface. As a universal base station it is  Security lock for mechanical
used for the operation and power supply attachment and electronic activation
Dimensions for the COM4LAB experiment boards of the experiment boards
and as an independent measuring  Anti-theft protection (port for
laboratory. The Master Unit can be Kensington lock)
2
 Circuit board: 280 × 200 mm simultaneously connected to up to four
digital terminal devices (PC, tablet or
LD Didactic GmbH Technical Documentation Page 36
 Scope of delivery  2 x 300 mm, blue Dimensions

 USB cable Technical data  Circuit board: 280 × 200 mm2

 NFC card  Frame: 296,5 × 354 mm2
 Rated voltage/current 600 V, CAT II /
10 A Supply voltage
ACCESSORIES  Lead cross section 0,5 mm²
 +15 V DC, −15 V DC und +5 V DC
from the Master Unit
70000-11 USB-C Charger 45 W
Europlug (Type C) ADDITIONALLY REQUIRED
Protective functions

PC, TABLET OR SMARTPHONE WITH A

CURRENT BROWSER  The use of safety cables avoids
unintentional short-circuiting.
 The use of a mask protects the
AUDIO ADAPTER 3,5 MM JACK FOR electronics from mechanical and
AUDIO PLAYERS SUCH AS MP3 electrical damage, e.g. by ESD
PLAYER, TABLET OR PC discharge.
 The use of a metal frame shields
electromagnetic fields and cools the
AUDIO PLAYER WITH DIFFERENT AUDIO electronics.
USB-C Charger with a 45 W quick FILES
charge function as a power supply for the Scope of delivery
COM4LAB Master Unit. An additional
ME5.1.4 BI- AND OMNIDIRECTIONAL
USB-A port with fast charge ensures
parallel charging of one mobile device. COMMUNICATION In addition to the experiment board itself,
the scope of delivery includes:

Technical data 70071-00 COM4LAB Board:

Reception and Transmission  mask
Technology  antenna set
 45 W PD, 15 V/3 A
 probe adapter 10:1 with a set of
 USB-A Port DC 5 V/2,4 A probes
 Overvoltage protection  2 x HF-cable, BNC-BNC, 1.5 m
 Overheat protection

Scope of delivery
70071-50 COM4LAB Course:
RxTx 4 - Bi- and
 2 m USB-C/USB-C cable
Omnidirectional
Communication

ALTERNATIVELY USB-C CHARGER

WITH UK-PLUG OR US-PLUG 70072-00 COM4LAB Extension
The experiment board to the COM4LAB Board: Band-Scanner
courses Analogue Transmission
70000-22 COM4LAB Set of Safety Techniques AM, FM and PSK, Digital
Leads, 2 mm, 24 pcs Modulations QPSK and QAM, Digital
Communication und Bi- and
Omnidirectional Communication
(supplied separately).

There are several function blocks on the

experiment board, which are put into
operation and also interconnected with
each other depending on the selected
experiment. The resulting circuits are
investigated in the course of the
corresponding experiments.
70000-00 COM4LAB Master Unit

A metal frame is screwed onto the

Set of highly fexible test leads with
experiment board. It serves to shield
insulation in PVC with assembled
electromagnetic fields between the
stackable 2 mm multilam plugs with rigid
individual function blocks and as a heat
insulating sleeve on both ends.
sink.

 6 x 150 mm, red The experiment board, housed within a

 6 x 150 mm, black sturdy board carrier, is to be used in
 2 x 150 mm, blue conjunction with, and powered by the
Master Unit (supplied separately). The COM4LAB Master Unit is a
 4 x 300 mm, red Circuits are wired by using BNC-BNC multifunctional, compact, measuring
 4 x 300 mm, black cables and 2 mm safety cables interface. As a universal base station it is
(supplied separately). used for the operation and power supply
LD Didactic GmbH Technical Documentation Page 37
 for the COM4LAB experiment boards  Security lock for mechanical  6 x 150 mm, red
and as an independent measuring attachment and electronic activation
laboratory. The Master Unit can be  6 x 150 mm, black
of the experiment boards
simultaneously connected to up to four  2 x 150 mm, blue
digital terminal devices (PC, tablet or
 Anti-theft protection (port for
Kensington lock)
 4 x 300 mm, red
smartphone) for the recording of  4 x 300 mm, black
measurements and for remote control of
its built-in functions. The Master Unit can Scope of delivery
 2 x 300 mm, blue
be quickly attached to an experiment
board. Its clear and structured design Technical data
results in easy operation.  USB cable
 NFC card
 Rated voltage/current 600 V, CAT II /
Dimensions 10 A
 Lead cross section 0,5 mm²
 295 x 154 × 30 mm3 ACCESSORIES

Integrated measuring instruments 70000-11 USB-C Charger 45 W ADDITIONALLY REQUIRED

Europlug (Type C)
 Two digital multimeters:
Voltage: DC/AC – 2 V | 20 V PC, TABLET OR SMARTPHONE WITH A
Current: DC/AC – 20 mA | 200 mA | CURRENT BROWSER
2A
Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2
MΩ AUDIO ADAPTER 3,5 MM JACK FOR
Autoranging for all measurement AUDIO PLAYERS SUCH AS MP3
ranges PLAYER, TABLET OR PC
 Digital Function Generator:
digitally generated sinusoidal,
triangular, square-wave signal types,
AUDIO PLAYER WITH DIFFERENT AUDIO
also DC FILES
Frequency range: 0.5 Hz – 100 kHz, USB-C Charger with a 45 W quick
also DC charge function as a power supply for the
SYNC output: TTL clock COM4LAB Master Unit. An additional ME5.2.1 DIGITAL COMMUNICATION
frequency 0.5 Hz – 100 kHz USB-A port with fast charge ensures TECHNOLOGY
Output voltage: max. ±10 V, (0 – 20 parallel charging of one mobile device.
V)
Output current: max. ±250 mA Technical data
 Digital 4-channel oscilloscope: THE COURSE DIGITAL COMMUNICATION
4 differential inputs TECHNOLOGY IS A PRACTICAL COURSE ON
 45 W PD, 15 V/3 A DIGITAL SIGNAL PROCESSING. ATTENTION IS
Sampling rate: 1 MS/s per channel
PAID TO THE REALISATION AND FUNCTION
Bandwidth: 200 kHz  USB-A Port DC 5 V/2,4 A
OF FIBRE OPTIC TRANSMISSION SYSTEMS
Memory depth: 1KS per channel  Overvoltage protection WITH EMPHASIS ON APPLICATIONS OF PCM
Resolution: 12 Bit per channel
 Overheat protection TECHNOLOGY, FOR EXAMPLE THE
Time ranges from 10 μs/div to 500
TRANSMISSION OF VOICE AND SIGNALS WITH
ms/div
REAL TELEPHONES, SOUND CARDS AND CD
Voltage ranges from 10 mV/div to 10 Scope of delivery PLAYERS.
V/div
Trigger CH1 - CH4 and EXT
(referenced to ground), in 4095  2 m USB-C/USB-C cable
steps, rising/falling edge LEARNING OBJECTIVES
 Digital analyzer:
8+1 digital signal inputs  LEARNING PHYSICAL BASIC PRINCIPLES
Input voltage TTL-compatible ALTERNATIVELY USB-C CHARGER
Sampling frequency: 200 Hz – 2  KNOWLEDGE OF VARIOUS
WITH UK-PLUG OR US-PLUG
TRANSMISSION METHODS
MHz
Memory depth: 9 Bit x 2 K
Triggering on any combination of the 70000-22 COM4LAB Set of Safety
input states Leads, 2 mm, 24 pcs TOPICS
Additional properties THE COURSE COVERS THE FOLLOWING
TOPICS:

 Voltage supply:
15 V/3 A  CHARACTERISTICS OF PULSE CARRIERS
USB-C  GENERATION OF PAM
 Interfaces:  PAM (NATURAL)
WLAN  PAM (S&H)
Ethernet 100 MBits RJ45
USB  PAM SPECTRUM
 Extensions:  OVER SAMPLING / UNDER SAMPLING
Extension Slot  ALIASING
USB Interface (type A) Set of highly fexible test leads with  SHANNON THEOREM
 NFC insulation in PVC with assembled
stackable 2 mm multilam plugs with rigid
 PULSE CODE MODULATION (PCM)
 Light strip & LEDs for status display
insulating sleeve on both ends.  QUANTISATION LINEAR & NON-LINEAR
 COMPRESSION / EXPANSION

LD Didactic GmbH Technical Documentation Page 38

  CODE ERRORS  Signal transmission by wire (coaxial
 TIME DIVISION MULTIPLEXING (TDM) line - two-wire line) 70000CBT DVD: COM3LAB
 SYCHRONISATION  Simplex / duplex communication Software
 QUANTISATION NOISE
 DIFFERENCE PULSE CODE MODULATION Optionally
(DPCM)
 OPTICAL SIGNAL TRANSMISSION  Transmission of voice (requires
 SIGNAL TRANSMISSION BY WIRE external signals, CD player,
(COAXIAL LINE - TWO-WIRE LINE) telephones etc.)
 SIMPLEX / DUPLEX COMMUNICATION  Influence of the trigger and type of
quantization on the speech
intelligibility
 Duplex communication (requires 2 x
COM3LAB Course Digital
7007301 COM3LAB Course: Communication Technology, as well
as external signal sources)
Digital Communication COM3LAB software package for Master
Technology - COM4LAB ready Unit 2.0 (700020) and 70000USB
Technical Data
DVD contains:
 2 x PAM Modulator
 2 x PCM Modulator  All available COM3LAB courses in all
 1 x Clock-pulse generator available languages
 2 x PAM Demodulator  COM3LAB starter software
 2 x PCM Demodulator  COM3LAB configurator
 1 x Signal source Sinus, 1 kHz  USB driver software for Master Unit
2.0
 1 x Signal source Sinus, 2 kHz
 1 x RJ-12 socket with hybrid
 .NET 4.0
termination circuit  Separate installation for the audio
package in all available languages
 1 x Jack bush for connecting external
signal sources
 1 x Jack bush for connecting external For each COM3LAB multimedia course
active speakers there is an electronic, interactive
Comprises an experiment board, housed instruction manual. The contents of the
 1 x Optical transmitter
manual are dependent on the topic and
within a board carrier, for use in  1 x Optical receiver
conjunction with, and powered by the are tailored to the hardware. The
Master Unit (700020, supplied operation and function of the manuals
separately) teaching a practical course Virtual Laboratory are identical for all courses. The 32-bit
on digital signal processing, experiments user interface, into which the interactive
being wired using 2 mm cables (700022, manual, the virtual lab and the tools are
supplied separately). Attention is paid to  Oscilloscope integrated, also remains the same for all
the realisation and function of fibre optic  Function Generator courses. Structure of multimedia course
transmission systems with emphasis on software:
 Multimeter (x2)
applications of PCM technology, for
example the transmission of voice and
 Digital Analyser
 Spectrum Analyser (FFT module)  Electronic manual
signals with real telephones, sound cards
and CD players. Course content,  Frequency Counter  The same look and the same
experiment instructions and tasks are operation for all courses
taught via course-specific software.  Quick and easy installation
Additional Functions
 Virtual lab (oscilloscope, multimeters,
Curriculum Coverage function generator etc.)
 Word Processing  Tools (printers, calculators, word
 Printer processing, copy function for
 Characteristics of pulse carriers measurement results)
 Pocket Calculator
 Generation of PAM  Help
 Free Experimentation
 PAM (natural)  Glossary
 Glossary
 PAM (S&H)  Table of contents
 PAM spectrum  Language (English, French, etc.) can
Additionally required
 Over sampling / under sampling be switched by pressing a button
 Aliasing  Readings and texts can be used in
 Shannon theorem  Digital Communication Technology your own documents
Accessories (7007302)  Zoomable
 Pulse code modulation (PCM)
 Quantisation linear & non-linear  Free selectable chapters
 Compression / expansion  Status display (successfully
processed, not processed)
 Code errors
The COM3LAB software contains  Evaluation of measurements and
 Time division multiplexing (TDM) courses in all supported languages and tasks
 Sychronisation the current version can be downloaded  Evaluation of the circuitry
 Quantisation noise from www.ld-didactic.de for free.
Alternatively, the COM3LAB software
 Difference pulse code modulation can also be obtained on DVD
(DPCM) (70000CBT).
 Optical signal transmission
LD Didactic GmbH Technical Documentation Page 39
 Additionally required:  Digital analyzer: 70000-11 USB-C Charger 45 W
Alternatively, the software 8+1 digital signal inputs Europlug (Type C)
Input voltage TTL-compatible
can be downloaded free of Sampling frequency: 200 Hz – 2
MHz
charge at SOFTWARE Memory depth: 9 Bit x 2 K
DOWNLOAD and is updated Triggering on any combination of the
input states
regularly.
Additional properties
70000-00 COM4LAB Master Unit
 Voltage supply:
15 V/3 A
USB-C USB-C Charger with a 45 W quick
 Interfaces: charge function as a power supply for the
WLAN COM4LAB Master Unit. An additional
Ethernet 100 MBits RJ45 USB-A port with fast charge ensures
USB parallel charging of one mobile device.
 Extensions:
Extension Slot Technical data
USB Interface (type A)
The COM4LAB Master Unit is a  NFC
multifunctional, compact, measuring  45 W PD, 15 V/3 A
interface. As a universal base station it is  Light strip & LEDs for status display
 USB-A Port DC 5 V/2,4 A
used for the operation and power supply  Security lock for mechanical
for the COM4LAB experiment boards attachment and electronic activation  Overvoltage protection
and as an independent measuring of the experiment boards  Overheat protection
laboratory. The Master Unit can be  Anti-theft protection (port for
simultaneously connected to up to four Kensington lock) Scope of delivery
digital terminal devices (PC, tablet or
smartphone) for the recording of
measurements and for remote control of Scope of delivery
 2 m USB-C/USB-C cable
its built-in functions. The Master Unit can
be quickly attached to an experiment
board. Its clear and structured design
 USB cable
results in easy operation.  NFC card
ALTERNATIVELY USB-C CHARGER
WITH UK-PLUG OR US-PLUG
Dimensions
ACCESSORIES 70000-22 COM4LAB Set of Safety
 295 x 154 × 30 mm3 Leads, 2 mm, 24 pcs
7007302 COM3LAB: Digital
Integrated measuring instruments Communication Technology
Accessories
 Two digital multimeters:
Voltage: DC/AC – 2 V | 20 V
Current: DC/AC – 20 mA | 200 mA | Required accessories for the COM3LAB
2A Course Digital Communication
Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2 Technology (7007301).
MΩ
Autoranging for all measurement
ranges Scope of Delivery
 Digital Function Generator:
digitally generated sinusoidal,  2 x Audio connection cable (jack Set of highly fexible test leads with
triangular, square-wave signal types, bush 3.5 mm) insulation in PVC with assembled
also DC stackable 2 mm multilam plugs with rigid
Frequency range: 0.5 Hz – 100 kHz,
 1 x Optical fiber with connectors, 3 m
insulating sleeve on both ends.
also DC
SYNC output: TTL clock
frequency 0.5 Hz – 100 kHz  6 x 150 mm, red
Output voltage: max. ±10 V, (0 – 20
V)
 6 x 150 mm, black
Output current: max. ±250 mA
Scope of delivery:  2 x 150 mm, blue
 Digital 4-channel oscilloscope:  4 x 300 mm, red
4 differential inputs  4 x 300 mm, black
Sampling rate: 1 MS/s per channel  2 x 300 mm, blue
Bandwidth: 200 kHz
Memory depth: 1KS per channel
Resolution: 12 Bit per channel Technical data
Time ranges from 10 μs/div to 500
ms/div
Voltage ranges from 10 mV/div to 10  Rated voltage/current 600 V, CAT II /
V/div 10 A
Trigger CH1 - CH4 and EXT  Lead cross section 0,5 mm²
(referenced to ground), in 4095
steps, rising/falling edge

LD Didactic GmbH Technical Documentation Page 40

ADDITIONALLY REQUIRED 7007401 COM3LAB Course:  ASK Modulator
Modem Technology -  FSK Modulator
PC WITH WINDOWS 7/8/10 64 BIT COM4LAB ready  2PSK Modulator
EDITION AND ONE FREE USB  4PSK Modulator
INTERFACE  Carrier generator
 Modulation multiplexer
ME5.2.2 MODEM TECHNOLOGY  Audio stage with piezo loudspeaker
 Channel level adapter
 Signal detector

THE COURSE MODEM TECHNOLOGY DEALS

 ASK demodulator
WITH THE FUNDAMENTALS AND  FSK demodulator
APPLICATIONS OF SHIFT KEYED SIGNALS  2PSK demodulator
AND MODEMS.  4PSK demodulator
 Carrier recovery
LEARNING OBJECTIVES
Virtual Laboratory

 LEARNING PHYSICAL BASIC PRINCIPLES

Comprises an experiment board, housed  Oscilloscope
within a board carrier, for use in
conjunction with, and powered by the
 Function Generator
TOPICS Master Unit (700020, supplied  Multimeter (x2)
separately) teaching a practical course  Digital Analyser
THE COURSE COVERS THE FOLLOWING on the fundamentals and applications of  Spectrum Analyser (FFT module)
TOPICS: shift keyed signals and modems,
experiments being wired using 2 mm  Frequency Counter
safety cables (700022, supplied  Data Transfer Module
 AMPLITUDE SHIFT KEYING (ASK) separately). Course content, experiment
 FREQUENCY SHIFT KEYING (FSK) instructions and tasks are taught via
Additional Functions
course-specific software.
 2-PHASE SHIFT KEYING (2PSK)
 4-PHASE SHIFT KEYING (4PSK) Curriculum Coverage  Word Processing
 DIFFERENCE PHASE CODING
 Printer
 SHIFT KEYED SIGNALS IN THE TIME
 Introduction  Pocket Calculator
DOMAIN
 SHIFT KEYED SIGNALS IN THE
 Amplitude shift keying (ASK)  Free Experimentation
FREQUENCY DOMAIN  Frequency shift keying (FSK)  Glossary
 ESTIMATION OF THE BANDWIDTH  2-phase shift keying (2PSK)
 MODULATION RATE / DATA RATE  4-phase shift keying (4PSK) The COM3LAB software contains
 Difference phase coding courses in all supported languages and
 SNR & BANDWIDTH
the current version can be downloaded
 HARDWARE OF THE MODULATORS  Shift keyed signals in the time from www.ld-didactic.de for free.
domain
 HARDWARE OF THE DEMODULATORS Alternatively, the COM3LAB software
 CARRIER RECOVERY &
 Shift keyed signals in the frequency can also be obtained on DVD
domain (70000CBT).
SYNCHRONISATION OF THE
DEMODULATORS  Estimation of the bandwidth
 ERROR CORRECTION  Modulation rate / data rate
 ERROR DETECTION  SNR & bandwidth
70000CBT DVD: COM3LAB
 OPERATIONAL MODES, SIMPLEX HALF  Hardware of the modulators
Software
DUPLEX, FULL DUPLEX  Hardware of the demodulators
 NRZ LINE CODE  Carrier recovery & synchronisation of
 FAULT SIMULATION the demodulators
 Error correction
 Error detection
 Operational modes, simplex half
duplex, full duplex
 NRZ line code
 Fault simulation

Optional

COM3LAB software package for Master

Communication of 2 PCs using modems Unit 2.0 (700020) and 70000USB
A 2nd workstation with a PC with a
Master Unit (700020) and the COM3LAB
course Modem Technology (7007401) is DVD contains:
required, as well as other accessories
(coaxial cable, star quad cable etc.) .
 All available COM3LAB courses in all
available languages
Technical Data  COM3LAB starter software
 COM3LAB configurator
 Data source for baseband signal
LD Didactic GmbH Technical Documentation Page 41
  USB driver software for Master Unit and as an independent measuring  Anti-theft protection (port for
2.0 laboratory. The Master Unit can be Kensington lock)
simultaneously connected to up to four
 .NET 4.0
digital terminal devices (PC, tablet or
 Separate installation for the audio smartphone) for the recording of Scope of delivery
package in all available languages measurements and for remote control of
its built-in functions. The Master Unit can
be quickly attached to an experiment  USB cable
For each COM3LAB multimedia course
there is an electronic, interactive board. Its clear and structured design  NFC card
instruction manual. The contents of the results in easy operation.
manual are dependent on the topic and
are tailored to the hardware. The Dimensions
operation and function of the manuals ACCESSORIES
are identical for all courses. The 32-bit
user interface, into which the interactive  295 x 154 × 30 mm3
manual, the virtual lab and the tools are
70000-11 USB-C Charger 45 W
integrated, also remains the same for all Europlug (Type C)
Integrated measuring instruments
courses. Structure of multimedia course
software:
 Two digital multimeters:
Voltage: DC/AC – 2 V | 20 V
 Electronic manual
Current: DC/AC – 20 mA | 200 mA |
 The same look and the same 2A
operation for all courses Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2
 Quick and easy installation MΩ
 Virtual lab (oscilloscope, multimeters, Autoranging for all measurement
function generator etc.) ranges
 Tools (printers, calculators, word  Digital Function Generator:
processing, copy function for digitally generated sinusoidal,
USB-C Charger with a 45 W quick
measurement results) triangular, square-wave signal types,
charge function as a power supply for the
also DC
 Help COM4LAB Master Unit. An additional
Frequency range: 0.5 Hz – 100 kHz,
 Glossary USB-A port with fast charge ensures
also DC
parallel charging of one mobile device.
 Table of contents SYNC output: TTL clock
frequency 0.5 Hz – 100 kHz
 Language (English, French, etc.) can
Output voltage: max. ±10 V, (0 – 20
be switched by pressing a button Technical data
V)
 Readings and texts can be used in Output current: max. ±250 mA
your own documents  45 W PD, 15 V/3 A
 Digital 4-channel oscilloscope:
 Zoomable 4 differential inputs  USB-A Port DC 5 V/2,4 A
 Free selectable chapters Sampling rate: 1 MS/s per channel  Overvoltage protection
 Status display (successfully Bandwidth: 200 kHz  Overheat protection
processed, not processed) Memory depth: 1KS per channel
Resolution: 12 Bit per channel
 Evaluation of measurements and
Time ranges from 10 μs/div to 500 Scope of delivery
tasks
ms/div
 Evaluation of the circuitry Voltage ranges from 10 mV/div to 10
V/div  2 m USB-C/USB-C cable
Trigger CH1 - CH4 and EXT
(referenced to ground), in 4095
steps, rising/falling edge
 Digital analyzer: ALTERNATIVELY USB-C CHARGER
Additionally required: 8+1 digital signal inputs WITH UK-PLUG OR US-PLUG
Alternatively, the software Input voltage TTL-compatible
Sampling frequency: 200 Hz – 2
can be downloaded free of MHz 70000-22 COM4LAB Set of Safety
charge at SOFTWARE Memory depth: 9 Bit x 2 K Leads, 2 mm, 24 pcs
Triggering on any combination of the
DOWNLOAD and is updated input states
regularly.
Additional properties
70000-00 COM4LAB Master Unit
 Voltage supply:
15 V/3 A
USB-C
 Interfaces:
WLAN
Ethernet 100 MBits RJ45
USB
 Extensions: Set of highly fexible test leads with
Extension Slot insulation in PVC with assembled
USB Interface (type A) stackable 2 mm multilam plugs with rigid
insulating sleeve on both ends.
The COM4LAB Master Unit is a  NFC
multifunctional, compact, measuring  Light strip & LEDs for status display
interface. As a universal base station it is  6 x 150 mm, red
used for the operation and power supply
 Security lock for mechanical
for the COM4LAB experiment boards
attachment and electronic activation  6 x 150 mm, black
of the experiment boards
LD Didactic GmbH Technical Documentation Page 42
  2 x 150 mm, blue 7007501 COM3LAB Course:  Multimeter (x2)
 4 x 300 mm, red Telecommunication Lines -  Digital Analyser
 4 x 300 mm, black COM4LAB ready  FFT Spectrum Analyser
 2 x 300 mm, blue  Frequency Counter
 Bode Module
Technical data
Additional Functions
 Rated voltage/current 600 V, CAT II /
10 A  Word Processing
 Lead cross section 0,5 mm²  Printer
 Pocket Calculator
 Free Experimentation
ADDITIONALLY REQUIRED  Glossary

PC WITH WINDOWS 7/8/10 64 BIT Additionally required

EDITION AND ONE FREE USB
INTERFACE  Telecommunication Lines
Comprises an experiment board, housed Accessories (7007502)
within a board carrier, for use in
ME5.3.1 TELECOMMUNICATION LINES conjunction with, and powered by the
Master Unit (700020, supplied
separately) teaching a practical course
on the fundamentals and applications of The COM3LAB software contains
THE COURSE TELECOMMUNICATION LINES various telecommunication line types, courses in all supported languages and
DEALS WITH THE FUNDAMENTALS AND experiments being wired using 2 mm the current version can be downloaded
APPLICATIONS OF VARIOUS safety cables (700022, supplied from www.ld-didactic.de for free.
TELECOMMUNICATION LINE TYPES. separately). Course content, experiment Alternatively, the COM3LAB software
instructions and tasks are taught via can also be obtained on DVD
course-specific software. (70000CBT).
LEARNING OBJECTIVES
Curriculum Coverage

 LEARNING PHYSICAL BASIC PRINCIPLES 70000CBT DVD: COM3LAB

 Frequency response of two wire lines
 Determination of characteristic wave Software
TOPICS impedance
 Measurement of near and far-end
crosstalk
THE COURSE COVERS THE FOLLOWING
TOPICS:  Impulse behaviour of coaxial lines
 Mismatching
 FREQUENCY RESPONSE OF TWO WIRE
 Hybrid & phantom circuit
LINES  Duplex transmission & remote supply
 DETERMINATION OF CHARACTERISTIC  Characteristic curves of LEDs in
WAVE IMPEDANCE optical communications engineering
 MEASUREMENT OF NEAR AND FAR-END  Attenuation of fibre optic lines
CROSSTALK  Measurement of optical power
 IMPULSE BEHAVIOUR OF COAXIAL LINES  Coupling losses COM3LAB software package for Master
 MISMATCHING  Bending losses Unit 2.0 (700020) and 70000USB
 HYBRID & PHANTOM CIRCUIT
 DUPLEX TRANSMISSION & REMOTE Technical Data DVD contains:
SUPPLY
 CHARACTERISTIC CURVES OF LEDS IN  All available COM3LAB courses in all
OPTICAL COMMUNICATIONS
 Equivalent circuits of two-wire lines
available languages
ENGINEERING  Equivalent line of four-wire lines
 COM3LAB starter software
 ATTENUATION OF FIBRE OPTIC LINES  Star quad with phantom circuit
 COM3LAB configurator
 COUPLING LOSSES  Hybrid termination circuit
 USB driver software for Master Unit
 BENDING LOSSES  Pulse generator 2.0
 Module for echo pulse evaluation  .NET 4.0
 Optical transmitter  Separate installation for the audio
 Optical level meter package in all available languages
 Shift unit for longitudinal offset on
fibre-optic cable For each COM3LAB multimedia course
 Signal sources 1 kHz / 2 kHz there is an electronic, interactive
instruction manual. The contents of the
manual are dependent on the topic and
Virtual Laboroatory
are tailored to the hardware. The
operation and function of the manuals
 Oscilloscope are identical for all courses. The 32-bit
user interface, into which the interactive
 Function Generator
manual, the virtual lab and the tools are

LD Didactic GmbH Technical Documentation Page 43

 integrated, also remains the same for all Integrated measuring instruments 7007502 COM3LAB:
courses. Structure of multimedia course
Telecommunication Lines
software:
 Two digital multimeters: Accessories
Voltage: DC/AC – 2 V | 20 V
 Electronic manual Current: DC/AC – 20 mA | 200 mA |
 The same look and the same 2A
Required accessories for the COM3LAB
operation for all courses Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2
Course Telecommunication Lines
MΩ
 Quick and easy installation
Autoranging for all measurement
(7007501).
 Virtual lab (oscilloscope, multimeters, ranges
function generator etc.) Scope of Delivery
 Digital Function Generator:
 Tools (printers, calculators, word digitally generated sinusoidal,
processing, copy function for triangular, square-wave signal types,
measurement results) also DC
 coaxial cable, 50m of RG 58
manufactures with BNC plug / plug
 Help Frequency range: 0.5 Hz – 100 kHz,
also DC  fibre-optic cable (20m)
 Glossary
SYNC output: TTL clock  fibre-optic cable (2m)
 Table of contents frequency 0.5 Hz – 100 kHz
 Language (English, French, etc.) can Output voltage: max. ±10 V, (0 – 20
be switched by pressing a button V)
 Readings and texts can be used in Output current: max. ±250 mA 70000-11 USB-C Charger 45 W
your own documents  Digital 4-channel oscilloscope: Europlug (Type C)
 Zoomable 4 differential inputs
Sampling rate: 1 MS/s per channel
 Free selectable chapters
Bandwidth: 200 kHz
 Status display (successfully Memory depth: 1KS per channel
processed, not processed) Resolution: 12 Bit per channel
 Evaluation of measurements and Time ranges from 10 μs/div to 500
tasks ms/div
 Evaluation of the circuitry Voltage ranges from 10 mV/div to 10
V/div
Trigger CH1 - CH4 and EXT
(referenced to ground), in 4095
steps, rising/falling edge
 Digital analyzer: USB-C Charger with a 45 W quick
Additionally required: 8+1 digital signal inputs charge function as a power supply for the
Input voltage TTL-compatible
Alternatively, the software Sampling frequency: 200 Hz – 2
COM4LAB Master Unit. An additional
USB-A port with fast charge ensures
can be downloaded free of MHz parallel charging of one mobile device.
Memory depth: 9 Bit x 2 K
charge at SOFTWARE Triggering on any combination of the
DOWNLOAD and is updated input states Technical data
regularly.
Additional properties  45 W PD, 15 V/3 A
70000-00 COM4LAB Master Unit  USB-A Port DC 5 V/2,4 A
 Voltage supply:  Overvoltage protection
15 V/3 A  Overheat protection
USB-C
 Interfaces: Scope of delivery
WLAN
Ethernet 100 MBits RJ45
USB  2 m USB-C/USB-C cable
 Extensions:
Extension Slot
USB Interface (type A)
 NFC ALTERNATIVELY USB-C CHARGER
The COM4LAB Master Unit is a
multifunctional, compact, measuring  Light strip & LEDs for status display WITH UK-PLUG OR US-PLUG
interface. As a universal base station it is  Security lock for mechanical
used for the operation and power supply attachment and electronic activation 70000-22 COM4LAB Set of Safety
for the COM4LAB experiment boards of the experiment boards
and as an independent measuring Leads, 2 mm, 24 pcs
 Anti-theft protection (port for
laboratory. The Master Unit can be Kensington lock)
simultaneously connected to up to four
digital terminal devices (PC, tablet or
smartphone) for the recording of Scope of delivery
measurements and for remote control of
its built-in functions. The Master Unit can
be quickly attached to an experiment  USB cable
board. Its clear and structured design  NFC card
results in easy operation.

Dimensions
ACCESSORIES
 295 x 154 × 30 mm3 Set of highly fexible test leads with
insulation in PVC with assembled

LD Didactic GmbH Technical Documentation Page 44

 stackable 2 mm multilam plugs with rigid
insulating sleeve on both ends.

 6 x 150 mm, red

 6 x 150 mm, black
 2 x 150 mm, blue
 4 x 300 mm, red
 4 x 300 mm, black
 2 x 300 mm, blue

Technical data

 Rated voltage/current 600 V, CAT II /

10 A
 Lead cross section 0,5 mm²

ADDITIONALLY REQUIRED

PC WITH WINDOWS 7/8/10 64 BIT

EDITION AND ONE FREE USB
INTERFACE

LD Didactic GmbH Technical Documentation Page 45

ME6.1.1 OPERATIONAL AMPLIFIER  FILTER CIRCUITS  Circuit board: 280 × 200 mm2
 Frame: 296,5 × 354 mm2
ACTIVE RC FILTER − PASSIVE RC
FILTER Supply voltage
THE COM4LAB COURSE ENTITLED
“OPERATIONAL AMPLIFIER” GIVES AN
INSIGHT INTO THE WORLD OF OPERATIONAL  STABILISATION CIRCUITS
AMPLIFIERS. FROM THE STANDARD CIRCUIT
 +15 V DC, −15 V DC und +5 V DC
TO THE REALIZATION OF A FUNCTION
from the Master Unit via
GENERATOR, ALL IMPORTANT TOPICS ARE CONSTANT VOLTAGE SOURCE − corresponding relays
DEALT WITH. THE COURSE COMPRISES 20 CONSTANT CURRENT SOURCE
CHAPTERS. Protective functions
 OSCILLATING CIRCUITS
TOTAL DURATION: UP TO 11 HOURS  Integrated reverse polarity protection
ASTABLE MULTIVIBRATOR − WIEN due to connection to the Master Unit
BRIDGE OSCILLATOR  The use of safety cables avoids
TARGET AUDIENCE unintentional short-circuiting

 FUNCTION GENERATOR
AMONG OTHERS, THE COURSE CAN BE
USED TO SUPPORT THE TRAINING PROCESS
70081-20 COM4LAB Course:
FOR THE FOLLOWING PROFESSIONS:
PREVIOUS Operational Amplifier
 ELECTRICAL SYSTEM FITTER KNOWLEDGE
 ELECTRONICS TECHNICIAN FOR
AUTOMATION TECHNOLOGY
THE STUDENTS NEED KNOWLEDGE OF THE
 ELECTRONICS TECHNICIAN FOR DESIGN OF ELECTRONIC CIRCUITS IN ORDER
ENERGY AND BUILDING TECHNOLOGY TO BE ABLE TO COMPLETE THE COURSE
 ELECTRONICS TECHNICIAN FOR SUCCESSFULLY. ADDITIONALLY, DEALING
DEVICES AND SYSTEMS WITH FORMULAS IS REQUIRED.
 ELECTRONICS TECHNICIAN FOR
INFORMATION AND SYSTEM
TECHNOLOGY
 ELECTRONICS TECHNICIAN FOR
MACHINE AND DRIVE TECHNOLOGY 70081-00 COM4LAB Board:
 AIRCRAFT ELECTRONICS TECHNICIAN Operational Amplifier
 SYSTEM ELECTRONICS TECHNICIAN

The COM4LAB course Operational

LEARNING Amplifier gives an insight into the world
of operational amplifiers. From the
standard circuit to the realization of a
OBJECTIVES function generator, all important topics
are dealt with. The course comprises 20
THE STUDENTS ARE TO: chapters.

The course covers the following topics:

 BE ABLE TO UNDERSTAND THE
CHARACTERISTICS AND OPERATION OF
THE OPERATIONAL AMPLIFIER AND  characteristics of an operational
 BE ABLE TO USE AND APPLY amplifier
OPERATIONAL AMPLIFIERS CORRECTLY.  inverting and non-inverting
operational amplifier
The experiment board to the COM4LAB  switches
TOPICS course Operational Amplifier (supplied
separately).
comparator − Schmitt trigger
THE COURSE COVERS THE FOLLOWING
There are 11 experiment panels on the
TOPICS:
experiment board. Each experiment  analogue arithmetic circuits
panel contains a self-contained circuit
 CHARACTERISTICS OF AN OPERATIONAL that is put into operation and examined
depending on the selected experiment. adder − subtracter − integrator −
AMPLIFIER
The active experiment panel is indicated differentiator
 INVERTING AND NON-INVERTING
by a lit green LED.
OPERATIONAL AMPLIFIER
 SWITCHES
 filter circuits
The experiment board, housed within a
sturdy board carrier, is to be used in
COMPARATOR − SCHMITT TRIGGER active RC filter − passive RC filter
conjunction with, and powered by the
Master Unit (supplied separately).
Circuits are wired by using 2 mm safety  stabilisation circuits
 ANALOGUE ARITHMETIC CIRCUITS
cables (supplied separately).

ADDER − SUBTRACTER −
constant voltage source − constant
Dimensions current source
INTEGRATOR − DIFFERENTIATOR

LD Didactic GmbH Technical Documentation Page 46

  oscillating circuits  295 x 154 × 30 mm3
70000-11 USB-C Charger 45 W
astable multivibrator − Wien bridge Integrated measuring instruments Europlug (Type C)
oscillator

 Two digital multimeters:

 function generator Voltage: DC/AC – 2 V | 20 V
Current: DC/AC – 20 mA | 200 mA |
2A
The course …
Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2
MΩ
 can be displayed and filled out on Autoranging for all measurement
your own tablet/smartphone/laptop. ranges
 is platform-independent - a current  Digital Function Generator:
browser is sufficient. digitally generated sinusoidal,
triangular, square-wave signal types,
 can be distributed to students via QR USB-C Charger with a 45 W quick
also DC
codes. charge function as a power supply for the
Frequency range: 0.5 Hz – 100 kHz, COM4LAB Master Unit. An additional
 enables interactive experimenting: also DC
USB-A port with fast charge ensures
The measured values from the SYNC output: TTL clock
Master Unit are automatically made parallel charging of one mobile device.
frequency 0.5 Hz – 100 kHz
available for evaluation in tables and Output voltage: max. ±10 V, (0 – 20
diagrams. The analysis and V) Technical data
documentation of the experiment on Output current: max. ±250 mA
the student device can be done at  Digital 4-channel oscilloscope:
school or at home. 4 differential inputs
 45 W PD, 15 V/3 A
 can be edited and thus adapted to Sampling rate: 1 MS/s per channel  USB-A Port DC 5 V/2,4 A
your own lesson plan. Bandwidth: 200 kHz  Overvoltage protection
Memory depth: 1KS per channel  Overheat protection
Resolution: 12 Bit per channel
Perpetual course license.
Time ranges from 10 μs/div to 500
ms/div Scope of delivery
Technical data Voltage ranges from 10 mV/div to 10
V/div
Trigger CH1 - CH4 and EXT  2 m USB-C/USB-C cable
 Product key for activation of the (referenced to ground), in 4095
course licence via steps, rising/falling edge
https://register.leylab.de is
 Digital analyzer:
necessary. Later on the course can
8+1 digital signal inputs ALTERNATIVELY USB-C CHARGER
be accessed and distributed from WITH UK-PLUG OR US-PLUG
Input voltage TTL-compatible
LeyLab.
Sampling frequency: 200 Hz – 2
 System requirements: MHz
- PC, tablet or smartphone with a Memory depth: 9 Bit x 2 K 70000-22 COM4LAB Set of Safety
current browser Triggering on any combination of the Leads, 2 mm, 24 pcs
- internet access input states

Additional properties
70000-00 COM4LAB Master Unit
 Voltage supply:
15 V/3 A
USB-C
 Interfaces:
WLAN
Ethernet 100 MBits RJ45
USB
 Extensions:
Extension Slot Set of highly fexible test leads with
USB Interface (type A) insulation in PVC with assembled
stackable 2 mm multilam plugs with rigid
The COM4LAB Master Unit is a  NFC insulating sleeve on both ends.
multifunctional, compact, measuring  Light strip & LEDs for status display
interface. As a universal base station it is  Security lock for mechanical
used for the operation and power supply attachment and electronic activation  6 x 150 mm, red
for the COM4LAB experiment boards of the experiment boards  6 x 150 mm, black
and as an independent measuring
laboratory. The Master Unit can be  Anti-theft protection (port for  2 x 150 mm, blue
simultaneously connected to up to four Kensington lock)  4 x 300 mm, red
digital terminal devices (PC, tablet or  4 x 300 mm, black
smartphone) for the recording of Scope of delivery  2 x 300 mm, blue
measurements and for remote control of
its built-in functions. The Master Unit can
be quickly attached to an experiment  USB cable Technical data
board. Its clear and structured design  NFC card
results in easy operation.
 Rated voltage/current 600 V, CAT II /
10 A
Dimensions  Lead cross section 0,5 mm²
ACCESSORIES

LD Didactic GmbH Technical Documentation Page 47

 ELECTRONIC CIRCUITS −  Circuit board: 280 × 200 mm2
TEMPERATURE SENSORS: PT100,
ADDITIONALLY REQUIRED  Frame: 296,5 × 354 mm2
NTC, KTY AND THERMOCOUPLE

PC, TABLET OR SMARTPHONE WITH A Supply voltage

 PRESSURE MEASUREMENT
CURRENT BROWSER  FORCE MEASUREMENT
 +15 V DC, −15 V DC und +5 V DC
from the Master Unit
ME6.1.2 SENSOR TECHNOLOGY WITH STRAIN GAUGES − WITH BENDING
BAR
Protective functions

THE COM4LAB COURSE ENTITLED  TORQUE MEASUREMENT

“SENSOR TECHNOLOGY” COVERS THE  The use of safety cables avoids
FUNDAMENTALS AND BASIC TERMS OF unintentional short-circuiting
WITH TORSION BAR
SENSORS. TYPICAL SENSORS ARE
EXPLAINED AND PRACTICALLY DEVISED
USING A NUMBER OF EXPERIMENTS. THE  ANGLE AND SPEED MEASUREMENT
COURSE COMPRISES 10 CHAPTERS.

WITH OPTICAL ENCODER Technical Data:

TOTAL DURATION: UP TO 8 HOURS

 DISPLACEMENT MEASUREMENT

TARGET AUDIENCE 70084-20 COM4LAB Course:

RESISTIVE − CAPACITIVE − Sensor Technology
INDUCTIVE − WITH ULTRASONIC
AMONG OTHERS, THE COURSE CAN BE SENSOR − WITH HALL SENSOR − WITH
USED TO SUPPORT THE TRAINING PROCESS REED SENSOR
FOR THE FOLLOWING PROFESSIONS AND The COM4LAB course entitled Sensor
SUBJECTS OF STUDY: Technology covers the fundamentals
 LIGHT MEASUREMENT and basic terms of sensors. Typical
sensors are explained and practically
 ELECTRONICS TECHNICIAN FOR devised using a number of experiments.


AUTOMATION TECHNOLOGY
ELECTRONICS TECHNICIAN FOR
PREVIOUS The course comprises 10 chapters.

ENERGY AND BUILDING TECHNOLOGY

 ELECTRONICS TECHNICIAN FOR
KNOWLEDGE The course covers the following topics:

DEVICES AND SYSTEMS

 ELECTRONICS TECHNICIAN FOR THE STUDENTS NEED TO HAVE A BASIC  temperature measurement
INFORMATION AND SYSTEM KNOWLEDGE OF ELECTRONIC COMPONENTS
TECHNOLOGY AND MEASUREMENT TECHNOLOGY IN electronic circuits − temperature
ORDER TO BE ABLE TO COMPLETE THE sensors: Pt100, NTC, KTY and
 ELECTRONICS TECHNICIAN FOR
COURSE SUCCESSFULLY. ADDITIONALLY, thermocouple
MACHINE AND DRIVE TECHNOLOGY
DEALING WITH SIMPLE FORMULAS IS
 AIRCRAFT ELECTRONICS TECHNICIAN
REQUIRED.
 MICROTECHNOLOGIST  pressure measurement
 MEASURING TECHNOLOGY  force measurement
(BACHELOR&APOS;S STUDIES)
 SENSOR TECHNOLOGY with strain gauges − with bending
(BACHELOR&APOS;S STUDIES) 70084-00 COM4LAB Board: bar
Sensor Technology

LEARNING  torque measurement

The experiment board to the COM4LAB
OBJECTIVES course Sensor Technology (supplied with torsion bar
separately).
THE STUDENTS ARE TO:  angle and speed measurement
There are several function blocks on the
experiment board, which are put into
 BE ABLE TO UNDERSTAND THE BASIC operation and also interconnected with with optical encoder
PRINCIPLES OF VARIOUS TYPICAL each other depending on the selected
SENSORS AND experiment. The resulting circuits are  displacement measurement
 BE ABLE TO UNDERSTAND THE investigated in the course of the
MEASUREMENT OF BASIC PHYSICAL corresponding experiments. The active
QUANTITIES. function blocks are indicated by a lit resistive − capacitive − inductive −
green LED. with ultrasonic sensor − with Hall
sensor − with reed sensor

TOPICS The experiment board, housed within a

sturdy board carrier, is to be used in  light measurement
conjunction with, and powered by the
THE COURSE COVERS THE FOLLOWING Master Unit (supplied separately).
TOPICS: Circuits are wired by using 2 mm safety The course …
cables (supplied separately).

 TEMPERATURE MEASUREMENT  can be displayed and filled out on

Dimensions your own tablet/smartphone/laptop.

LD Didactic GmbH Technical Documentation Page 48

  is platform-independent - a current  Digital Function Generator: 70000-11 USB-C Charger 45 W
browser is sufficient. digitally generated sinusoidal, Europlug (Type C)
 can be distributed to students via QR triangular, square-wave signal types,
codes. also DC
Frequency range: 0.5 Hz – 100 kHz,
 enables interactive experimenting:
also DC
The measured values from the
SYNC output: TTL clock
Master Unit are automatically made
frequency 0.5 Hz – 100 kHz
available for evaluation in tables and
Output voltage: max. ±10 V, (0 – 20
diagrams. The analysis and
V)
documentation of the experiment on
Output current: max. ±250 mA
the student device can be done at
school or at home.  Digital 4-channel oscilloscope:
4 differential inputs
 can be edited and thus adapted to
Sampling rate: 1 MS/s per channel
your own lesson plan. Bandwidth: 200 kHz USB-C Charger with a 45 W quick
Memory depth: 1KS per channel charge function as a power supply for the
Perpetual course license. Resolution: 12 Bit per channel COM4LAB Master Unit. An additional
Time ranges from 10 μs/div to 500 USB-A port with fast charge ensures
ms/div parallel charging of one mobile device.
Technical data Voltage ranges from 10 mV/div to 10
V/div
Trigger CH1 - CH4 and EXT Technical data
 Product key for activation of the
course licence via (referenced to ground), in 4095
https://register.leylab.de is steps, rising/falling edge
 45 W PD, 15 V/3 A
necessary. Later on the course can  Digital analyzer:
be accessed and distributed from 8+1 digital signal inputs  USB-A Port DC 5 V/2,4 A
LeyLab. Input voltage TTL-compatible  Overvoltage protection
 System requirements: Sampling frequency: 200 Hz – 2  Overheat protection
- PC, tablet or smartphone with a MHz
current browser Memory depth: 9 Bit x 2 K
Triggering on any combination of the Scope of delivery
- internet access
input states
 2 m USB-C/USB-C cable
Additional properties
70000-00 COM4LAB Master Unit
 Voltage supply: ALTERNATIVELY USB-C CHARGER
15 V/3 A
USB-C WITH UK-PLUG OR US-PLUG
 Interfaces:
WLAN 70000-22 COM4LAB Set of Safety
Ethernet 100 MBits RJ45 Leads, 2 mm, 24 pcs
USB
 Extensions:
Extension Slot
USB Interface (type A)
The COM4LAB Master Unit is a  NFC
multifunctional, compact, measuring
 Light strip & LEDs for status display
interface. As a universal base station it is
used for the operation and power supply  Security lock for mechanical
for the COM4LAB experiment boards attachment and electronic activation
and as an independent measuring of the experiment boards
laboratory. The Master Unit can be  Anti-theft protection (port for
simultaneously connected to up to four Kensington lock)
digital terminal devices (PC, tablet or
smartphone) for the recording of
Scope of delivery Set of highly fexible test leads with
measurements and for remote control of
its built-in functions. The Master Unit can insulation in PVC with assembled
be quickly attached to an experiment stackable 2 mm multilam plugs with rigid
 USB cable insulating sleeve on both ends.
board. Its clear and structured design
results in easy operation.  NFC card

 6 x 150 mm, red

Dimensions  6 x 150 mm, black
ACCESSORIES  2 x 150 mm, blue
 295 x 154 × 30 mm 3  4 x 300 mm, red
 4 x 300 mm, black
Integrated measuring instruments  2 x 300 mm, blue

 Two digital multimeters: Technical data

Voltage: DC/AC – 2 V | 20 V
Current: DC/AC – 20 mA | 200 mA |
2A
 Rated voltage/current 600 V, CAT II /
10 A
Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2
MΩ  Lead cross section 0,5 mm²
Autoranging for all measurement
ranges

LD Didactic GmbH Technical Documentation Page 49

ADDITIONALLY REQUIRED  ANALYSIS OF CONTROLLED SYSTEMS  +15 V DC, −15 V DC und +5 V DC
 CONTROLLED SYSTEMS WITH from the Master Unit
COMPENSATION
PC, TABLET OR SMARTPHONE WITH A
CURRENT BROWSER  HIGHER-ORDER CONTROLLED SYSTEMS Protective functions
 CONTROLLED SYSTEMS WITHOUT
COMPENSATION
ME6.2.2 INTRODUCTION TO CONTROL  The use of safety cables avoids
 CONTROLLER TYPES unintentional short-circuiting
ENGINEERING  P, I, PI, PD AND PID CONTROL
 AUTOMATIC DIGITAL CONTROL

THE COM4LAB COURSE ENTITLED

70082-20 COM4LAB Course:
“INTRODUCTION TO CONTROL
ENGINEERING” IS THE FIRST COURSE ON
PREVIOUS Introduction to Control
Engineering
THE CONTROL ENGINEERING. THE BASIC
CONCEPTS AND LAWS OF CONTROL
KNOWLEDGE
ENGINEERING ARE EXPLAINED AND
PRACTICALLY DEVISED USING A NUMBER OF THE STUDENTS NEED TO HAVE A BASIC
EXPERIMENTS. THE COURSE COMPRISES 12 KNOWLEDGE OF ELECTRONIC COMPONENTS
CHAPTERS. IN ORDER TO BE ABLE TO COMPLETE THE
COURSE SUCCESSFULLY. ADDITIONALLY,
TOTAL DURATION: UP TO 8 HOURS DEALING WITH SIMPLE FORMULAS IS
REQUIRED.

TARGET AUDIENCE
AMONG OTHERS, THE COURSE CAN BE 70082-00 COM4LAB Board:
USED TO SUPPORT THE TRAINING PROCESS Control Engineering
FOR THE FOLLOWING PROFESSIONS AND
SUBJECTS OF STUDY:

The COM4LAB course Introduction to

 ELECTRONICS TECHNICIAN FOR Control Engineering is the first course
AUTOMATION TECHNOLOGY to the control engineering. The basic
concepts and laws of control engineering
 ELECTRONICS TECHNICIAN FOR
are explained and practically devised
ENERGY AND BUILDING TECHNOLOGY
using a number of experiments. The
 ELECTRONICS TECHNICIAN FOR course comprises 12 chapters.
DEVICES AND SYSTEMS
 ELECTRONICS TECHNICIAN FOR
The course covers the following topics:
INFORMATION AND SYSTEM
TECHNOLOGY
 ELECTRONICS TECHNICIAN FOR  open-loop control
MACHINE AND DRIVE TECHNOLOGY  closed-loop control
 AIRCRAFT ELECTRONICS TECHNICIAN The experiment board to the COM4LAB  analysis of controlled systems
 courses Introduction to Control
AUTOMATION TECHNOLOGY
Engineering, Control Loops and  controlled systems with
(BACHELOR&APOS;S STUDIES) compensation
Stability and Applied Modern Control
 CONTROL ENGINEERING Engineering (supplied separately).  higher-order controlled systems
(BACHELOR&APOS;S STUDIES)  controlled systems without
There are several function blocks on the compensation
experiment board, which are put into  controller types
LEARNING operation and also interconnected with  P, I, PI, PD and PID control
each other depending on the selected  digital control
OBJECTIVES experiment. The resulting circuits are
investigated in the course of the
corresponding experiments. The active The course …
THE STUDENTS ARE TO: function blocks are indicated by a lit
green LED.
 can be displayed and filled out on
 BE ABLE TO UNDERSTAND THE BASIC your own tablet/smartphone/laptop.
PRINCIPLES OF CONTROL ENGINEERING The experiment board, housed within a
AND sturdy board carrier, is to be used in
 is platform-independent - a current
browser is sufficient.
 BE ABLE TO UNDERSTAND AND TO conjunction with, and powered by the
PARAMETRISE THE BASIC ELEMENTS OF Master Unit (supplied separately).  can be distributed to students via QR
Circuits are wired by using 2 mm safety codes.
CONTROL ENGINEERING.
cables (supplied separately).  enables interactive experimenting:
The measured values from the
Master Unit are automatically made
TOPICS Dimensions
available for evaluation in tables and
diagrams. The analysis and
 Circuit board: 280 × 200 mm2 documentation of the experiment on
THE COURSE COVERS THE FOLLOWING
the student device can be done at
TOPICS:  Frame: 296,5 × 354 mm2
school or at home.
 can be edited and thus adapted to
 OPEN-LOOP CONTROL Supply voltage your own lesson plan.
 CLOSED-LOOP CONTROL

LD Didactic GmbH Technical Documentation Page 50

 Perpetual course license. Resolution: 12 Bit per channel Scope of delivery
Time ranges from 10 μs/div to 500
ms/div
Technical data  2 m USB-C/USB-C cable
Voltage ranges from 10 mV/div to 10
V/div
 Product key for activation of the Trigger CH1 - CH4 and EXT
course licence via (referenced to ground), in 4095
https://register.leylab.de is steps, rising/falling edge ALTERNATIVELY USB-C CHARGER
necessary. Later on the course can  Digital analyzer: WITH UK-PLUG OR US-PLUG
be accessed and distributed from 8+1 digital signal inputs
LeyLab. Input voltage TTL-compatible
Sampling frequency: 200 Hz – 2 70000-22 COM4LAB Set of Safety
 System requirements:
- PC, tablet or smartphone with a MHz Leads, 2 mm, 24 pcs
current browser Memory depth: 9 Bit x 2 K
- internet access Triggering on any combination of the
input states

Additional properties
70000-00 COM4LAB Master Unit
 Voltage supply:
15 V/3 A
USB-C
 Interfaces:
WLAN
Ethernet 100 MBits RJ45
USB Set of highly fexible test leads with
 Extensions: insulation in PVC with assembled
Extension Slot stackable 2 mm multilam plugs with rigid
USB Interface (type A) insulating sleeve on both ends.
The COM4LAB Master Unit is a  NFC
multifunctional, compact, measuring
interface. As a universal base station it is
 Light strip & LEDs for status display  6 x 150 mm, red
used for the operation and power supply  Security lock for mechanical  6 x 150 mm, black
for the COM4LAB experiment boards attachment and electronic activation  2 x 150 mm, blue
and as an independent measuring of the experiment boards
 4 x 300 mm, red
laboratory. The Master Unit can be  Anti-theft protection (port for
simultaneously connected to up to four Kensington lock)
 4 x 300 mm, black
digital terminal devices (PC, tablet or  2 x 300 mm, blue
smartphone) for the recording of
measurements and for remote control of Scope of delivery
Technical data
its built-in functions. The Master Unit can
be quickly attached to an experiment  USB cable
board. Its clear and structured design  Rated voltage/current 600 V, CAT II /
results in easy operation.  NFC card
10 A
 Lead cross section 0,5 mm²
Dimensions
ACCESSORIES
 295 x 154 × 30 mm3 ADDITIONALLY REQUIRED
70000-11 USB-C Charger 45 W
Integrated measuring instruments Europlug (Type C)
PC, TABLET OR SMARTPHONE WITH A
CURRENT BROWSER
 Two digital multimeters:
Voltage: DC/AC – 2 V | 20 V
Current: DC/AC – 20 mA | 200 mA | ME6.2.3 CONTROL LOOPS AND
2A STABILITY
Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2
MΩ
Autoranging for all measurement
ranges THE COM4LAB COURSE ENTITLED
 Digital Function Generator: “CONTROL LOOPS AND STABILITY” IS THE
digitally generated sinusoidal, SECOND COURSE ON THE CONTROL
triangular, square-wave signal types, ENGINEERING. THE BASIC CONCEPTS AND
USB-C Charger with a 45 W quick
also DC charge function as a power supply for the LAWS OF THE CONTROL LOOPS ARE
Frequency range: 0.5 Hz – 100 kHz, EXPLAINED AND PRACTICALLY DEVISED
COM4LAB Master Unit. An additional
also DC USING A NUMBER OF EXPERIMENTS. THE
USB-A port with fast charge ensures
SYNC output: TTL clock COURSE COMPRISES 10 CHAPTERS.
parallel charging of one mobile device.
frequency 0.5 Hz – 100 kHz
Output voltage: max. ±10 V, (0 – 20
Technical data TOTAL DURATION: UP TO 8 HOURS
V)
Output current: max. ±250 mA
 Digital 4-channel oscilloscope:
4 differential inputs


45 W PD, 15 V/3 A
USB-A Port DC 5 V/2,4 A
TARGET AUDIENCE
Sampling rate: 1 MS/s per channel
Bandwidth: 200 kHz  Overvoltage protection
AMONG OTHERS, THE COURSE CAN BE
Memory depth: 1KS per channel  Overheat protection USED TO SUPPORT THE TRAINING PROCESS

LD Didactic GmbH Technical Documentation Page 51

 FOR THE FOLLOWING PROFESSIONS AND (COM4LAB COURSE: INTRODUCTION TO 70082-30 COM4LAB Course:
SUBJECTS OF STUDY: CONTROL ENGINEERING) IN ORDER TO BE
ABLE TO COMPLETE THE COURSE
Control Loops and Stability
SUCCESSFULLY. ADDITIONALLY, DEALING
 ELECTRONICS TECHNICIAN FOR WITH SIMPLE FORMULAS IS REQUIRED.
AUTOMATION TECHNOLOGY
 ELECTRONICS TECHNICIAN FOR
ENERGY AND BUILDING TECHNOLOGY
 ELECTRONICS TECHNICIAN FOR
DEVICES AND SYSTEMS 70082-00 COM4LAB Board:
 ELECTRONICS TECHNICIAN FOR Control Engineering
INFORMATION AND SYSTEM
TECHNOLOGY
 ELECTRONICS TECHNICIAN FOR
MACHINE AND DRIVE TECHNOLOGY
 AIRCRAFT ELECTRONICS TECHNICIAN
 AUTOMATION TECHNOLOGY
(BACHELOR&APOS;S STUDIES)
 CONTROL ENGINEERING
(BACHELOR&APOS;S STUDIES) The COM4LAB course Control Loops
and Stability is the second course to the
control engineering. The basic concepts
LEARNING and laws of the control loops are
explained and practically devised using a
number of experiments. The course
OBJECTIVES comprises 10 chapters.
The experiment board to the COM4LAB
courses Introduction to Control
THE STUDENTS ARE TO: The course covers the following topics:
Engineering, Control Loops and
Stability and Applied Modern Control
 BE ABLE TO UNDERSTAND THE BASIC
Engineering (supplied separately).  stability of automatic control systems
PRINCIPLE OF CONTROL LOOPS AND  performance criteria for automatic
THE EVALUATION OF CONTROL LOOPS There are several function blocks on the control loops
(STABILITY, PERFORMANCE CRITERIA), experiment board, which are put into  optimisation guideliness for PID
 BE ABLE TO UNDERSTAND THE operation and also interconnected with controllers
IMPLEMENTATION OF CONTROLLERS each other depending on the selected
FOR REAL TECHNICAL CONTROLLED experiment. The resulting circuits are  controller design according to
investigated in the course of the Ziegler/Nichols
SYSTEMS AND
 BE ABLE TO UNDERSTAND THE FAULT
corresponding experiments. The active  automatic temperature control
function blocks are indicated by a lit  automatic speed control
IDENTIFICATION IN CONTROL LOOPS.
green LED.
 automatic light control
 automatic control of controlled
TOPICS The experiment board, housed within a
sturdy board carrier, is to be used in
systems without compensation

conjunction with, and powered by the

 automatic control with discontinuous
controllers
THE COURSE COVERS THE FOLLOWING Master Unit (supplied separately).
TOPICS: Circuits are wired by using 2 mm safety  fault simulation
cables (supplied separately).
The course …
 STABILITY OF AUTOMATIC CONTROL
Dimensions
SYSTEMS
 PERFORMANCE CRITERIA FOR  can be displayed and filled out on
AUTOMATIC CONTROL LOOPS  Circuit board: 280 × 200 mm2 your own tablet/smartphone/laptop.
 OPTIMISATION GUIDELINESS FOR PID  Frame: 296,5 × 354 mm2  is platform-independent - a current
CONTROLLERS browser is sufficient.
 CONTROLLER DESIGN ACCORDING TO Supply voltage
 can be distributed to students via QR
ZIEGLER/NICHOLS codes.
 AUTOMATIC TEMPERATURE CONTROL  enables interactive experimenting:
 AUTOMATIC SPEED CONTROL
 +15 V DC, −15 V DC und +5 V DC The measured values from the
from the Master Unit Master Unit are automatically made
 AUTOMATIC LIGHT CONTROL available for evaluation in tables and
 AUTOMATIC CONTROL OF CONTROLLED
Protective functions
diagrams. The analysis and
SYSTEMS WITHOUT COMPENSATION documentation of the experiment on
 AUTOMATIC CONTROL WITH the student device can be done at
DISCONTINUOUS CONTROLLERS  The use of safety cables avoids school or at home.
 FAULT SIMULATION unintentional short-circuiting  can be edited and thus adapted to
your own lesson plan.

PREVIOUS Perpetual course license.

KNOWLEDGE Technical data

THE STUDENTS NEED TO HAVE A BASIC  Product key for activation of the
KNOWLEDGE OF ELECTRONIC COMPONENTS course licence via
AND OF CONTROL ENGINEERING https://register.leylab.de is

LD Didactic GmbH Technical Documentation Page 52

 necessary. Later on the course can  Digital analyzer: ALTERNATIVELY USB-C CHARGER
be accessed and distributed from 8+1 digital signal inputs WITH UK-PLUG OR US-PLUG
LeyLab. Input voltage TTL-compatible
 System requirements: Sampling frequency: 200 Hz – 2
- PC, tablet or smartphone with a MHz 70000-22 COM4LAB Set of Safety
current browser Memory depth: 9 Bit x 2 K Leads, 2 mm, 24 pcs
- internet access Triggering on any combination of the
input states

Additional properties
70000-00 COM4LAB Master Unit
 Voltage supply:
15 V/3 A
USB-C
 Interfaces:
WLAN
Ethernet 100 MBits RJ45
USB
 Extensions: Set of highly fexible test leads with
Extension Slot insulation in PVC with assembled
USB Interface (type A) stackable 2 mm multilam plugs with rigid
The COM4LAB Master Unit is a insulating sleeve on both ends.
multifunctional, compact, measuring
 NFC
interface. As a universal base station it is  Light strip & LEDs for status display
used for the operation and power supply  Security lock for mechanical  6 x 150 mm, red
for the COM4LAB experiment boards attachment and electronic activation  6 x 150 mm, black
and as an independent measuring of the experiment boards
laboratory. The Master Unit can be  2 x 150 mm, blue
 Anti-theft protection (port for
 4 x 300 mm, red
simultaneously connected to up to four Kensington lock)
digital terminal devices (PC, tablet or  4 x 300 mm, black
smartphone) for the recording of
Scope of delivery
 2 x 300 mm, blue
measurements and for remote control of
its built-in functions. The Master Unit can
be quickly attached to an experiment Technical data
board. Its clear and structured design  USB cable
results in easy operation.  NFC card
 Rated voltage/current 600 V, CAT II /
10 A
Dimensions
 Lead cross section 0,5 mm²
ACCESSORIES
 295 x 154 × 30 mm3
70000-11 USB-C Charger 45 W ADDITIONALLY REQUIRED
Integrated measuring instruments Europlug (Type C)
PC, TABLET OR SMARTPHONE WITH A
 Two digital multimeters:
Voltage: DC/AC – 2 V | 20 V CURRENT BROWSER
Current: DC/AC – 20 mA | 200 mA |
2A ME6.2.4 APPLIED MODERN CONTROL
Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2
MΩ ENGINEERING
Autoranging for all measurement
ranges
 Digital Function Generator: THE COM4LAB COURSE ENTITLED
digitally generated sinusoidal, “APPLIED MODERN CONTROL
triangular, square-wave signal types, ENGINEERING” IS THE THIRD AND FINAL
also DC USB-C Charger with a 45 W quick
charge function as a power supply for the COURSE ON THE CONTROL ENGINEERING.
Frequency range: 0.5 Hz – 100 kHz, THE APPROACHES OF MODERN CONTROL
also DC COM4LAB Master Unit. An additional
USB-A port with fast charge ensures STRATEGIES FOR THE CONTROL OF
SYNC output: TTL clock COMPLEX SYSTEMS (E. G. IN THE
frequency 0.5 Hz – 100 kHz parallel charging of one mobile device.
AUTOMOTIVE INDUSTRY OR AEROSPACE) AS
Output voltage: max. ±10 V, (0 – 20 WELL AS THE INFLUENCE OF TECHNICAL
V) Technical data LIMITATIONS ON THE CONTROL LOOPS ARE
Output current: max. ±250 mA EXPLAINED AND PRACTICALLY DEVISED
 Digital 4-channel oscilloscope: USING A NUMBER OF EXPERIMENTS. THE
4 differential inputs  45 W PD, 15 V/3 A FINAL CHAPTER OFFERS THE POSSIBILITY
Sampling rate: 1 MS/s per channel  USB-A Port DC 5 V/2,4 A FOR FREE EXPERIMENTATION WITH
Bandwidth: 200 kHz  Overvoltage protection COMPATIBLE EXTERNAL CONTROLLED
Memory depth: 1KS per channel SYSTEMS. THE COURSE COMPRISES 10
Resolution: 12 Bit per channel
 Overheat protection
CHAPTERS.
Time ranges from 10 μs/div to 500
ms/div Scope of delivery
Voltage ranges from 10 mV/div to 10 TOTAL DURATION: UP TO 8 HOURS
V/div
Trigger CH1 - CH4 and EXT  2 m USB-C/USB-C cable
(referenced to ground), in 4095
steps, rising/falling edge
TARGET AUDIENCE
LD Didactic GmbH Technical Documentation Page 53
 AMONG OTHERS, THE COURSE CAN BE 70082-40 COM4LAB Course:
USED TO SUPPORT THE TRAINING PROCESS
FOR THE FOLLOWING PROFESSIONS AND
Applied Modern Control
SUBJECTS OF STUDY: 70082-00 COM4LAB Board: Engineering
Control Engineering
 ELECTRONICS TECHNICIAN FOR
DEVICES AND SYSTEMS
 AIRCRAFT ELECTRONICS TECHNICIAN
 AUTOMATION TECHNOLOGY
(BACHELOR&APOS;S STUDIES)
 CONTROL ENGINEERING
(BACHELOR&APOS;S STUDIES)

LEARNING
OBJECTIVES
THE STUDENTS ARE TO: The experiment board to the COM4LAB
courses Introduction to Control The COM4LAB course entitled “Applied
Engineering, Control Loops and Modern Control Engineering” is the third
 BE ABLE TO UNDERSTAND THE BASIC Stability and Applied Modern Control and final course on the control
PRINCIPLES OF MODERN CONTROL Engineering (supplied separately). engineering. The approaches of modern
STRATEGIES, control strategies for the control of
 BE ABLE TO UNDERSTAND THE complex systems (e. g. in the automotive
There are several function blocks on the industry or aerospace) as well as the
INFLUENCE OF TECHNICAL LIMITATIONS
experiment board, which are put into influence of technical limitations on the
ON THE CONTROL LOOPS AND
operation and also interconnected with control loops are explained and
 BE ABLE TO APPLY AND EXPAND THE each other depending on the selected practically devised using a number of
KNOWLEDGE THEY HAVE ACQUIRED experiment. The resulting circuits are experiments. The final chapter offers the
FROM ALL COM4LAB CONTROL investigated in the course of the possibility for free experimentation with
ENGINEERING COURSES IN FREE corresponding experiments. The active compatible external controlled systems.
EXPERIMENTATION WITH EXTERNAL function blocks are indicated by a lit The course comprises 10 chapters.
CONTROLLED SYSTEMS. green LED.

The course covers the following topics:

The experiment board, housed within a
TOPICS sturdy board carrier, is to be used in
conjunction with, and powered by the  systems with dead time
Master Unit (supplied separately).  constraint of the manipulated
THE COURSE COVERS THE FOLLOWING Circuits are wired by using 2 mm safety
TOPICS: variable
cables (supplied separately).
 cascade control

  introduction to frequency response

SYSTEMS WITH DEAD TIME Dimensions
 CONSTRAINT OF THE MANIPULATED
 frequency response of individual
basic elements
VARIABLE
 Circuit board: 280 × 200 mm2  frequency response of combined
 CASCADE CONTROL
elements
 Frame: 296,5 × 354 mm2
 INTRODUCTION TO FREQUENCY
 controller desing in frequency
RESPONSE
domain
 FREQUENCY RESPONSE OF INDIVIDUAL
Supply voltage
BASIC ELEMENTS
 fuzzy control

  adaptive control
FREQUENCY RESPONSE OF COMBINED  +15 V DC, −15 V DC und +5 V DC
ELEMENTS from the Master Unit  free experimentation with external
controlled systems
 CONTROLLER DESING IN FREQUENCY
DOMAIN
Protective functions
 FUZZY CONTROL The course …
 ADAPTIVE CONTROL
 The use of safety cables avoids
 FREE EXPERIMENTATION WITH unintentional short-circuiting  can be displayed and filled out on
EXTERNAL CONTROLLED SYSTEMS your own tablet/smartphone/laptop.
 is platform-independent - a current
browser is sufficient.
PREVIOUS  can be distributed to students via QR
codes.
KNOWLEDGE  enables interactive experimenting:
The measured values from the
Master Unit are automatically made
THE STUDENTS NEED TO HAVE A BASIC available for evaluation in tables and
KNOWLEDGE OF ELECTRONIC COMPONENTS diagrams. The analysis and
AND OF CONTROL ENGINEERING documentation of the experiment on
(COM4LAB COURSE: INTRODUCTION TO the student device can be done at
CONTROL ENGINEERING, COM4LAB school or at home.
COURSE: CONTROL LOOPS AND STABILITY)
IN ORDER TO BE ABLE TO COMPLETE THE
 can be edited and thus adapted to
your own lesson plan.
COURSE SUCCESSFULLY. ADDITIONALLY,
DEALING WITH FORMULAS IS REQUIRED.

LD Didactic GmbH Technical Documentation Page 54

 Perpetual course license. Resolution: 12 Bit per channel Scope of delivery
Time ranges from 10 μs/div to 500
ms/div
Technical data  2 m USB-C/USB-C cable
Voltage ranges from 10 mV/div to 10
V/div
 Product key for activation of the Trigger CH1 - CH4 and EXT
course licence via (referenced to ground), in 4095
https://register.leylab.de is steps, rising/falling edge ALTERNATIVELY USB-C CHARGER
necessary. Later on the course can  Digital analyzer: WITH UK-PLUG OR US-PLUG
be accessed and distributed from 8+1 digital signal inputs
LeyLab. Input voltage TTL-compatible
Sampling frequency: 200 Hz – 2 70000-22 COM4LAB Set of Safety
 System requirements:
- PC, tablet or smartphone with a MHz Leads, 2 mm, 24 pcs
current browser Memory depth: 9 Bit x 2 K
- internet access Triggering on any combination of the
input states

Additional properties
70000-00 COM4LAB Master Unit
 Voltage supply:
15 V/3 A
USB-C
 Interfaces:
WLAN
Ethernet 100 MBits RJ45
USB Set of highly fexible test leads with
 Extensions: insulation in PVC with assembled
Extension Slot stackable 2 mm multilam plugs with rigid
USB Interface (type A) insulating sleeve on both ends.
The COM4LAB Master Unit is a  NFC
multifunctional, compact, measuring
interface. As a universal base station it is
 Light strip & LEDs for status display  6 x 150 mm, red
used for the operation and power supply  Security lock for mechanical  6 x 150 mm, black
for the COM4LAB experiment boards attachment and electronic activation  2 x 150 mm, blue
and as an independent measuring of the experiment boards
 4 x 300 mm, red
laboratory. The Master Unit can be  Anti-theft protection (port for
simultaneously connected to up to four Kensington lock)
 4 x 300 mm, black
digital terminal devices (PC, tablet or  2 x 300 mm, blue
smartphone) for the recording of
measurements and for remote control of Scope of delivery
Technical data
its built-in functions. The Master Unit can
be quickly attached to an experiment  USB cable
board. Its clear and structured design  Rated voltage/current 600 V, CAT II /
results in easy operation.  NFC card
10 A
 Lead cross section 0,5 mm²
Dimensions
ACCESSORIES
 295 x 154 × 30 mm3 ADDITIONALLY REQUIRED
70000-11 USB-C Charger 45 W
Integrated measuring instruments Europlug (Type C)
PC, TABLET OR SMARTPHONE WITH A
CURRENT BROWSER
 Two digital multimeters:
Voltage: DC/AC – 2 V | 20 V
Current: DC/AC – 20 mA | 200 mA | ME6.3.1 AUTOMATION AND BUS
2A TECHNOLOGY
Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2
MΩ
Autoranging for all measurement
ranges THE COURSE BUS AND AUTOMATION
 Digital Function Generator: TECHNOLOGY PROVIDES BASIC
digitally generated sinusoidal, KNOWLEDGE ABOUT PROGRAMMABLE LOGIC
triangular, square-wave signal types, CONTROLLERS (PLC). WITH MANY
USB-C Charger with a 45 W quick
also DC EXAMPLES, EXPLANATIONS, EXERCISES AND
charge function as a power supply for the
Frequency range: 0.5 Hz – 100 kHz, PRACTICAL TASKS, THE BASICS AND
COM4LAB Master Unit. An additional
also DC FUNCTIONALITY OF THE PLC ARE VIVIDLY
USB-A port with fast charge ensures
SYNC output: TTL clock PRESENTED.
parallel charging of one mobile device.
frequency 0.5 Hz – 100 kHz
Output voltage: max. ±10 V, (0 – 20 THE COURSE ALSO INCLUDES A PROFIBUS
V) Technical data
INTERFACE TO ENABLE AN OPTIONAL
Output current: max. ±250 mA COMBINATION WITH EXTERNAL PROFIBUS
 Digital 4-channel oscilloscope:  45 W PD, 15 V/3 A COMPONENTS OR AN EXTERNAL PLANT
4 differential inputs SIMULATOR, THUS ENABLING THE
Sampling rate: 1 MS/s per channel  USB-A Port DC 5 V/2,4 A
PROCESSES IN BUS AND AUTOMATION
Bandwidth: 200 kHz  Overvoltage protection TECHNOLOGY TO BE REPRESENTED AND
Memory depth: 1KS per channel  Overheat protection

LD Didactic GmbH Technical Documentation Page 55

 UNDERSTOOD REALISTICALLY AND WITHOUT practical tasks, the base and mode of 70000CBT DVD: COM3LAB
GREAT EFFORT. operation of the PLC and PROFIBUS are
represented. Experiments are wired by
Software
using 2 mm safety cables (700022,
LEARNING OBJECTIVES supplied separately). Course content,
experiment instructions and tasks are
taught via course-specific software.
 INDEPENDENT IMPLEMENTATION OF A
PROJECT
Curriculum Coverage
 PROGRAMMING
 PROJECT PLANNING
 COMMISSIONING
 Basics and basic terms (IEC 1131) of
the PLC
 ANALYSIS
 Logic connections, times, counters,
 CORRECTION data processing & program editing
 Simple sensors & signal conditioning COM3LAB software package for Master
with analogue digital transformers &
TOPICS multiplexers
Unit 2.0 (700020) and 70000USB

 Projecting of an automatisation
THE COURSE COVERS THE FOLLOWING system DVD contains:
TOPICS:  Programming & initiation of the PLC
 Data transfer structures & protocols  All available COM3LAB courses in all
 BASICS AND BASIC TERMS (IEC 1131)  Transfer & error analysis available languages
OF THE PLC  Connection of external components  COM3LAB starter software
 LOGIC CONNECTIONS, TIMES,  Link of PROFIBUS users (GSD)  COM3LAB configurator
COUNTERS, DATA PROCESSING AND  USB driver software for Master Unit
PROGRAM EDITING 2.0
 SIMPLE SENSORS & SIGNAL Technical Data
 .NET 4.0
CONDITIONING WITH ANALOGUE DIGITAL
TRANSFORMERS & MULTIPLEXERS
 Separate installation for the audio
 24 digital inputs package in all available languages
 PROJECTING OF AN AUTOMATISATION  8 analog inputs
SYSTEM
 Sensors: Temperature sensor, For each COM3LAB multimedia course
 PROGRAMMING & INITIATION OF THE Phototransistor there is an electronic, interactive
PLC
 20 digital outputs instruction manual. The contents of the
 DATA TRANSFER STRUCTURES & manual are dependent on the topic and
PROTOCOLS  2 analog outputs
are tailored to the hardware. The
 TRANSFER & ERROR ANALYSIS  1 Motor operation and function of the manuals
 CONNECTION OF EXTERNAL  Dimmable incandescent lamp are identical for all courses. The 32-bit
COMPONENTS  4 mm sockets for external application user interface, into which the interactive
manual, the virtual lab and the tools are
 LINK OF PROFIBUS USERS (GSD)  Connection for external PROFIBUS integrated, also remains the same for all
components courses. Structure of multimedia course
 PROFIBUS (1 Master, 2 Slaves) software:

Virtual Laboratory  Electronic manual

7003101 COM3LAB Course:
Automation and Bus  The same look and the same
 Oscilloscope operation for all courses
Technology - COM4LAB ready
 Function Generator  Quick and easy installation
 Multimeter (x2)  Virtual lab (oscilloscope, multimeters,
 PROFIBUS analyser function generator etc.)
 PLC Control  Tools (printers, calculators, word
processing, copy function for
 PLC Program measurement results)
 Process In/Out  Help
 Glossary
Additional Functions  Table of contents
 Language (English, French, etc.) can
 Word Processing be switched by pressing a button
 Printer  Readings and texts can be used in
 Pocket Calculator your own documents
 Free Experimentation  Zoomable
 Glossary  Free selectable chapters
 Status display (successfully
Comprises an experiment board, housed processed, not processed)
within a board carrier, for use in The COM3LAB software contains
conjunction with, and powered by the courses in all supported languages and  Evaluation of measurements and
the current version can be downloaded tasks
Master Unit (700020, supplied
separately) teaching the basics of a from www.ld-didactic.de for free.  Evaluation of the circuitry
programmable logic controller (PLC) and Alternatively, the COM3LAB software
showing it's networking capability can also be obtained on DVD
including the use of sensors and (70000CBT).
actuatores by means of the PROFIBUS.
With many examples, explanations and
Additionally required:
LD Didactic GmbH Technical Documentation Page 56
 Alternatively, the software Input voltage TTL-compatible
Sampling frequency: 200 Hz – 2
can be downloaded free of MHz 70000-22 COM4LAB Set of Safety
charge at SOFTWARE Memory depth: 9 Bit x 2 K Leads, 2 mm, 24 pcs
Triggering on any combination of the
DOWNLOAD and is updated input states
regularly.
Additional properties
70000-00 COM4LAB Master Unit
 Voltage supply:
15 V/3 A
USB-C
 Interfaces:
WLAN
Ethernet 100 MBits RJ45
USB
 Extensions: Set of highly fexible test leads with
Extension Slot insulation in PVC with assembled
USB Interface (type A) stackable 2 mm multilam plugs with rigid
insulating sleeve on both ends.
The COM4LAB Master Unit is a  NFC
multifunctional, compact, measuring  Light strip & LEDs for status display
interface. As a universal base station it is  Security lock for mechanical  6 x 150 mm, red
used for the operation and power supply attachment and electronic activation  6 x 150 mm, black
for the COM4LAB experiment boards of the experiment boards  2 x 150 mm, blue
and as an independent measuring  Anti-theft protection (port for
laboratory. The Master Unit can be  4 x 300 mm, red
Kensington lock)
simultaneously connected to up to four  4 x 300 mm, black
digital terminal devices (PC, tablet or  2 x 300 mm, blue
smartphone) for the recording of Scope of delivery
measurements and for remote control of
its built-in functions. The Master Unit can Technical data
be quickly attached to an experiment  USB cable
board. Its clear and structured design  NFC card
 Rated voltage/current 600 V, CAT II /
results in easy operation.
10 A
 Lead cross section 0,5 mm²
Dimensions
ACCESSORIES
 295 x 154 × 30 mm3
70000-11 USB-C Charger 45 W ADDITIONALLY REQUIRED
Europlug (Type C)
Integrated measuring instruments
PC WITH WINDOWS 7/8/10 64 BIT
EDITION AND ONE FREE USB
 Two digital multimeters:
Voltage: DC/AC – 2 V | 20 V INTERFACE
Current: DC/AC – 20 mA | 200 mA |
2A ME6.3.2 ELECTROPNEUMATICS
Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2
MΩ
Autoranging for all measurement
ranges
THE COURSE ELECTROPNEUMATICS
 Digital Function Generator: TEACHES THE BASICS OF
digitally generated sinusoidal, ELECTROPNEUMATICS USING THE BIBB
triangular, square-wave signal types, USB-C Charger with a 45 W quick
STANDARD TASKS.
also DC charge function as a power supply for the
Frequency range: 0.5 Hz – 100 kHz, COM4LAB Master Unit. An additional
USB-A port with fast charge ensures
also DC
SYNC output: TTL clock parallel charging of one mobile device. LEARNING OBJECTIVES
frequency 0.5 Hz – 100 kHz
Output voltage: max. ±10 V, (0 – 20 Technical data  LEARNING PHYSICAL BASIC PRINCIPLES
V)
Output current: max. ±250 mA
 Digital 4-channel oscilloscope:  45 W PD, 15 V/3 A TOPICS
4 differential inputs  USB-A Port DC 5 V/2,4 A
Sampling rate: 1 MS/s per channel  Overvoltage protection
Bandwidth: 200 kHz THE COURSE COVERS THE FOLLOWING
Memory depth: 1KS per channel
 Overheat protection TOPICS:
Resolution: 12 Bit per channel
Time ranges from 10 μs/div to 500 Scope of delivery
ms/div
 BASICS OF PNEUMATICS/ELECTRO-
PNEUMATICS
Voltage ranges from 10 mV/div to 10
V/div  2 m USB-C/USB-C cable  PNEUMATIC AND ELECTRIC CIRCUIT
Trigger CH1 - CH4 and EXT DIAGRAMS
(referenced to ground), in 4095  PILOT CONTROL OF A SINGLE-ACTING
steps, rising/falling edge CYLINDER
 Digital analyzer: ALTERNATIVELY USB-C CHARGER  PILOT CONTROL OF A DOUBLE-ACTING
8+1 digital signal inputs WITH UK-PLUG OR US-PLUG CYLINDER

LD Didactic GmbH Technical Documentation Page 57

  HOLDING ELEMENT CONTROL Technical Data  3 x 5/2 electric displacement valves
 BASIC CIRCUIT WITH AND FUNCTION with spring return
 BASIC CIRCUIT WITH OR FUNCTION  6 relays, 4 changeover contacts  1 x central switch-on valve for
pressure supply, controlled by
 BASIC CIRCUIT WITH ELECTRIC  1 time relay (switch-on and switch-off
COM3LAB
LATCHING CIRCUITS time delay)
  3 x displacement sensor for double-
 DISPLACEMENT-DEPENDENT CONTROL 1 Pressure transducer
acting cylinders
 TIME-DEPENDENT CONTROL, SWITCH-  1 Pressure sensor 0 .. 10 bar
ON AND SWITCH-OFF TIME DELAY  Operating and monitoring elements
 PRESSURE-DEPENDENT CONTROL  24 V voltage supply
Scope of delivery:
 SEQUENTIAL CONTROLS
Virtual Laboratory  1 x PU plastic hose 5m long and 2.5
mm thick
 6 x adapter cables (2 mm) on socket
 Oscilloscope connectors
7003501 COM3LAB Course:  Function Generator  20 x blanking elements
Electro Pneumatics -  Multimeter (x2)  1 x screwdriver
COM4LAB ready  Digital analyser  1 x flat ribbon cabl
 1 x set of safety cables (2mm, 18
Additional Functions Qty., 60cm)

 Word Processing A compressor is required which is

 Printer supplied separately. We recommend our
Low Noise Compressor (744600).
 Pocket Calculator
 Free Experimentation
If you supply your own compressor with,
 Glossary the minimum requirements are:

The COM3LAB software contains

courses in all supported languages and  Connection power: 15 W
the current version can be downloaded  Pressure: 500 kPa
from www.ld-didactic.de for free.  Feed rate: 2 litres per minute
Alternatively, the COM3LAB software
can also be obtained on DVD
Comprises an experiment board, housed (70000CBT).
within a board carrier, for use in 70000CBT DVD: COM3LAB
conjunction with, and powered by the
Master Unit (700020, supplied
Software
separately) teaching a practical course 700351 COM3LAB: Pneumatics
on pneumatics and electro-pneumatics. Board
In order to perform experiments, this
board can either be connected with
industry-standard valve technology or
with the Pneumatics Board (700351,
supplied separately) to perform all of the
experiments. The wiring of the
experiments is carried out over 2 mm
safety cables (700022, supplied
separately). Course content, experiment
instructions and tasks are taught via
course-specific software.
COM3LAB software package for Master
Curriculum Coverage Unit 2.0 (700020) and 70000USB

DVD contains:
 Basics of pneumatics/electro-
pneumatics
Selected by users of the COM3LAB course
 Pneumatic and electric circuit Electro Pneumatics (7003501) as an  All available COM3LAB courses in all
diagrams optional, recommended item, this board available languages
 Pilot control of a single-acting will monitor the components with the  COM3LAB starter software
cylinder integrated displacement sensors of the  COM3LAB configurator
 Pilot control of a double-acting cylinders.
 USB driver software for Master Unit
cylinder 2.0
Technical Data:
 Holding element control  .NET 4.0
 Basic circuit with AND function  Separate installation for the audio
 Basic circuit with OR function  1 x single-acting cylinder, spring package in all available languages
return with capacitive end switch
 Basic circuit with electric latching
circuits  3 x double-acting cylinder with
For each COM3LAB multimedia course
displacement sensor and cylinder
 Displacement-dependent control switch there is an electronic, interactive
 Time-dependent control, switch-on instruction manual. The contents of the
 4 x throttle valves manual are dependent on the topic and
and switch-off time delay
 3 x 5/2 electric displacement are tailored to the hardware. The
 Pressure-dependent control impulse valves operation and function of the manuals
 Sequential controls are identical for all courses. The 32-bit
LD Didactic GmbH Technical Documentation Page 58
 user interface, into which the interactive  295 x 154 × 30 mm3
manual, the virtual lab and the tools are
integrated, also remains the same for all 70000-11 USB-C Charger 45 W
courses. Structure of multimedia course Integrated measuring instruments Europlug (Type C)
software:
 Two digital multimeters:
 Electronic manual Voltage: DC/AC – 2 V | 20 V
Current: DC/AC – 20 mA | 200 mA |
 The same look and the same
2A
operation for all courses
Resistance: 2 kΩ | 20 kΩ | 200 kΩ | 2
 Quick and easy installation MΩ
 Virtual lab (oscilloscope, multimeters, Autoranging for all measurement
function generator etc.) ranges
 Tools (printers, calculators, word  Digital Function Generator:
processing, copy function for digitally generated sinusoidal,
measurement results) triangular, square-wave signal types,
USB-C Charger with a 45 W quick
 Help also DC
charge function as a power supply for the
Frequency range: 0.5 Hz – 100 kHz, COM4LAB Master Unit. An additional
 Glossary also DC
USB-A port with fast charge ensures
 Table of contents SYNC output: TTL clock
parallel charging of one mobile device.
 Language (English, French, etc.) can frequency 0.5 Hz – 100 kHz
be switched by pressing a button Output voltage: max. ±10 V, (0 – 20
V) Technical data
 Readings and texts can be used in
your own documents Output current: max. ±250 mA
 Zoomable  Digital 4-channel oscilloscope:
 45 W PD, 15 V/3 A
4 differential inputs
 Free selectable chapters Sampling rate: 1 MS/s per channel  USB-A Port DC 5 V/2,4 A
 Status display (successfully Bandwidth: 200 kHz  Overvoltage protection
processed, not processed) Memory depth: 1KS per channel  Overheat protection
 Evaluation of measurements and Resolution: 12 Bit per channel
tasks Time ranges from 10 μs/div to 500
ms/div Scope of delivery
 Evaluation of the circuitry
Voltage ranges from 10 mV/div to 10
V/div
Trigger CH1 - CH4 and EXT  2 m USB-C/USB-C cable
(referenced to ground), in 4095
steps, rising/falling edge
Additionally required:  Digital analyzer:
ALTERNATIVELY USB-C CHARGER
8+1 digital signal inputs
Alternatively, the software Input voltage TTL-compatible WITH UK-PLUG OR US-PLUG
can be downloaded free of Sampling frequency: 200 Hz – 2
MHz
charge at SOFTWARE Memory depth: 9 Bit x 2 K 70000-22 COM4LAB Set of Safety
DOWNLOAD and is updated Triggering on any combination of the Leads, 2 mm, 24 pcs
input states
regularly.
Additional properties
70000-00 COM4LAB Master Unit
 Voltage supply:
15 V/3 A
USB-C
 Interfaces:
WLAN
Ethernet 100 MBits RJ45
USB
 Extensions:
Extension Slot Set of highly fexible test leads with
USB Interface (type A) insulation in PVC with assembled
The COM4LAB Master Unit is a stackable 2 mm multilam plugs with rigid
 NFC insulating sleeve on both ends.
multifunctional, compact, measuring
interface. As a universal base station it is  Light strip & LEDs for status display
used for the operation and power supply  Security lock for mechanical
attachment and electronic activation  6 x 150 mm, red
for the COM4LAB experiment boards
and as an independent measuring of the experiment boards  6 x 150 mm, black
laboratory. The Master Unit can be  Anti-theft protection (port for  2 x 150 mm, blue
simultaneously connected to up to four Kensington lock)  4 x 300 mm, red
digital terminal devices (PC, tablet or
smartphone) for the recording of
 4 x 300 mm, black
measurements and for remote control of Scope of delivery  2 x 300 mm, blue
its built-in functions. The Master Unit can
be quickly attached to an experiment Technical data
board. Its clear and structured design
 USB cable
results in easy operation.  NFC card
 Rated voltage/current 600 V, CAT II /
Dimensions 10 A

ACCESSORIES  Lead cross section 0,5 mm²

LD Didactic GmbH Technical Documentation Page 59

ADDITIONALLY REQUIRED

PC WITH WINDOWS 7/8/10 64 BIT

EDITION AND ONE FREE USB
INTERFACE

LD Didactic GmbH Technical Documentation Page 60