Scribd
Upload
200 views10 pages

How To Clean A Circuit Board

The document provides guidance on cleaning circuit boards, including: 1) It discusses dry cleaning methods like vacuuming, air dusters, and lens brushes to remove loose dust and dirt. 2) It covers wet cleaning methods like isopropyl alcohol, cleaning pens, and ultrasonic cleaners to dissolve and remove stuck-on contaminants. 3) It recommends establishing a repeatable cleaning process including dry pre-cleaning, wet cleaning, rinsing, drying, and final inspection.

Uploaded by

jack
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
200 views10 pages

How To Clean A Circuit Board

The document provides guidance on cleaning circuit boards, including: 1) It discusses dry cleaning methods like vacuuming, air dusters, and lens brushes to remove loose dust and dirt. 2) It covers wet cleaning methods like isopropyl alcohol, cleaning pens, and ultrasonic cleaners to dissolve and remove stuck-on contaminants. 3) It recommends establishing a repeatable cleaning process including dry pre-cleaning, wet cleaning, rinsing, drying, and final inspection.

Uploaded by

jack
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 10

RAYMING PCB & ASSEMBLY

How to Clean a Circuit Board ?


Introduction

Circuit boards, also known as PCBs (printed circuit boards), form the backbone of
most electronic devices. Over time, PCBs can accumulate dirt, grime, dust and other
contaminants during manufacturing, storage, and use. Cleaning helps remove these
contaminants to prevent issues like short circuits, corrosion, and impaired thermal
performance. However, care must be taken not to damage sensitive board components
while cleaning.

This comprehensive guide covers methods, materials, and best practices for safely and
effectively cleaning circuit boards in electronics production, maintenance, and repair.

Reasons for Cleaning Circuit Boards

Cleaning PCBs provides both functional and aesthetic benefits:

 Removes contaminants that may lead to shorts, false signals, and impaired
connections
 Helps dissipate heat efficiently by removing thermal insulators like dust and
grime
 Prevents arcing and leakage current issues in high voltage boards
 Protects components and metal traces against corrosion
 Improves conformal coating adhesion and appearance
 Restores boards to visually clean condition for inspection
 Removes residual fluxes after soldering to avoid further oxidation

Thorough cleaning should be standard procedure in PCB fabrication, rework, repair,


and maintenance processes.

Safety Considerations for PCB Cleaning

Cleaning agents and methods can damage delicate board components if not done
properly. Follow these safety guidelines:

 Review board construction and identify sensitive components (MEMS,


displays). Take extra care near them.
 Avoid cleaning agents that can damage component materials and metallic
traces. Match cleaning solutions carefully.
 Use anti-static safety gear to avoid electrostatic discharge (ESD) through
components.

PCB Manufacturing & Assembly Services https://www.raypcb.com/


RAYMING PCB & ASSEMBLY

 Allow sufficient drying time before reconnecting power to avoid short circuits.
 Follow directions for proper usage and handling of commercial cleaning
agents like solvents.

Working safely prevents introducing new issues like ESD damage, chemical
corrosion, and residual moisture while cleaning boards.

Request PCB Manufacturing Quote Now

Dry Cleaning Methods for PCBs

PCB Cleaning

Dry cleaning techniques avoid using liquids for removing contaminants:

Vacuuming

Vacuuming is an easy dry method for removing loose dust and dirt from PCB
assemblies.

Procedure:

 Use an ESD-safe vacuum with a brush nozzle attachment


 Vacuum across exposed surfaces of the board, focusing on high buildup areas
 Angle the brush to dislodge stubborn contaminants
 Check areas under large components and sockets

Pros:

 Fast, gentle, and efficient for removing loose particulate debris


 Mobile vacuums allow cleaning mounted boards

PCB Manufacturing & Assembly Services https://www.raypcb.com/


RAYMING PCB & ASSEMBLY

Cons:

 Ineffective for sticky oils/greases or removing corrosion

Air Duster Spray

Pressurized air cans release high pressure gas that can dislodge contaminants.

Procedure:

 Hold can 6-8 inches from board surface


 Blast short bursts across and under components, connectors etc.
 Wipe away dislodged particles with lint-free cloth

Pros:

 Quickly removes dust and surface debris


 Reaches narrow spaces under components

Cons:

 Does not remove stuck-on contaminants


 Air blast can damage fragile parts if not careful

Lens Brush

Soft, flexible lens cleaning brushes can remove contaminants from hard-to-reach
spots.

Procedure:

 Use light pressure and brush across board surface


 Reach into tight spaces between board parts
 Fold brush tip to expose fresh bristles

Pros:

 Versatile for meticulous dry cleaning of delicate areas


 Compact and portable

Cons:

 Time consuming for large boards


 Cannot remove strongly adhered contaminants

PCB Manufacturing & Assembly Services https://www.raypcb.com/


RAYMING PCB & ASSEMBLY

Dry cleaning works well for removing loose dust, dirt and small particulate matter
from circuit boards.

Wet Cleaning Methods for PCBs

No-Clean Flux vs. Water Soluble Flux

Wet cleaning methods use solutions to dissolve and displace stuck-on contaminants:

Isopropyl Alcohol (IPA)

IPA is a mild organic solvent commonly used for PCB cleaning.

Procedure:

 Soak lint-free cloth or swabs in 99% pure IPA


 Wipe across board surface, applying moderate pressure on stained areas
 Allow to air dry fully before reconnecting power

Pros:

 Removes light oils, fluxes, thermal paste from boards


 Evaporates quickly without residue
 Low cost and easily available

Cons:

 May not remove heavy grease or corrosion


 Can damage rubbers, plastics if left too long

Cleaning Pens

PCB Manufacturing & Assembly Services https://www.raypcb.com/


RAYMING PCB & ASSEMBLY

Pens containing IPA or other cleaning solutions allow spot cleaning deposits.

Procedure:

 Shake pen to saturate nib with cleaning solution


 Rub nib gently over contamination area
 Let ink dissolve deposit for 10-30 seconds
 Wipe away contamination with nib

Pros:

 Allows precision cleaning of specific spots


 Easy to carry for field use

Cons:

 Takes effort to clear heavy buildup


 May leave traces of cleaning solution residue

Ultrasonic Cleaner

Ultrasonic energy helps dislodge dried contaminants from boards.

Procedure:

 Fill tank with suitable cleaning solvent like IPA, water, or detergent
 Immerse board and energize ultrasonic transducer
 Run for 5-10 minutes allowing cavitation to remove contaminants
 Rinse board with clean solvent after ultrasonic cleaning

Pros:

 Very effective for removing old, dried contamination


 Able to penetrate tight spaces and component undersides
 Does not require rubbing or scrubbing

Cons:

 Requires an ultrasonic system with solvent tank


 Care needed to avoid component detachment

Wet cleaning processes help clear more stubborn, adhered on grime, oils and fluxes
from PCBs.

Request PCB Manufacturing Quote Now

PCB Manufacturing & Assembly Services https://www.raypcb.com/


RAYMING PCB & ASSEMBLY

Cleaning Agents for PCBs

How to solder the chip components-Cleaning Solder Resist

Choosing the right cleaning solution ensures effective contaminant removal without
damaging boards:

 Isopropyl alcohol (IPA) – General purpose cleaner suitable for light oils and
fluxes
 Acetone – Stronger than IPA but can damage component plastics
 Cleaning solvents – Proprietary blends optimized for PCB cleaning
applications
 Water – Inexpensive but leaves conductive residues requiring thorough drying
 Detergents – Used as safer aqueous cleaners combined with water
 Ozone-based cleaners – Effective cleaners made from ozone gas in water

Factors like cost, safety, component compatibility and waste disposal guide the
selection of PCB cleaning agents.

Cleaning Different PCB Assemblies

PCB Manufacturing & Assembly Services https://www.raypcb.com/


RAYMING PCB & ASSEMBLY

PCB cleaning methods may vary by board type and assembly:

Bare Boards

 New blank PCBs – Use IPA rub to remove manufacturing residues


 Reworked boards – Clean light corrosion; degrease if thermal paste was used

Coated Boards

 Avoid coating damage from rubbing. Soak swab in IPA and lightly wipe.

Conformal Coated Boards

 Gently wipe with solvent like acetone before recoating to improve adhesion

Assembled Boards

 Vacuum loose dust. Use air duster on components. Exercise caution.


 Swab clean between components with lens brush and IPA-soaked tips
 For heavy buildup, partial disassembly may be required for access

Assess PCB components and type before selecting suitable cleaning method.

PCB Cleaning Process

Follow a systematic approach for consistent cleaning results:

1. Dry Pre-cleaning – Use vacuum, brush and air spray for loose contaminants.

2. Wet Cleaning – Apply preferred solvent like IPA and wipe board. Allow to dry.

3. Rinsing – Use fresh solvent to remove any remaining cleaning agent residues.

4. Drying – Allow board to dry fully before reassembly and testing.

5. Final wipedown – Wipe with lint-free cloth to remove any remaining lint, fibers or
dust.

6. Visual inspection – Inspect under bright light for cleanliness before reassembly.

Establishing a repeatable process helps achieve contaminant-free PCBs.

PCB Manufacturing & Assembly Services https://www.raypcb.com/


RAYMING PCB & ASSEMBLY

Cleaning Tips for PCB Maintenance

Some best practices for cleaning during PCB maintenance and repair:

 Assess buildup and select suitable cleaning method – solvent wipe for light
oils or ultrasonic bath for heavy residue.
 Take photos before disassembly as a guide for correct reassembly.
 Use anti-static safety gear to prevent ESD damage which may look like new
contamination.
 For coated boards, clean only affected areas to minimize coating wear.
 Rinse with fresh solvent after wet cleaning and allow longer drying time for
densely populated boards.
 Visually inspect under bright light or microscope after cleaning to check for
residue.
 Properly store cleaned boards in anti-static bags before system reassembly.

Meticulous cleaning as part of regular maintenance keeps PCBs contaminant-free for


reliable performance.

Conclusion

Cleaning is an important process for removing potentially harmful PCB contaminants


like grime, dusts, oils and fluxes. Dry cleaning techniques like vacuuming, air spray
and lens brushing remove loose particulate matter. For clearing heavier residue, wet
cleaning with solutions like isopropyl alcohol is more effective. With the right process
and cleaning agents, even old stubborn contamination on boards can be cleared
without component damage for restored board performance.

PCB Manufacturing & Assembly Services https://www.raypcb.com/


RAYMING PCB & ASSEMBLY

Frequently Asked Questions about Cleaning Circuit

Boards

Here are some common questions about PCB cleaning:

Q: What are some must-have supplies for cleaning PCBs?

A: Useful supplies are high purity isopropyl alcohol, cleaning swabs, lens brushes,
low-pressure air duster, ESD-safe mat, lint-free wipes, magnifying glass.

Q: How often should PCB maintenance cleaning be done?

A: For normal environments, annual cleaning suffices. In harsh industrial conditions


with more contaminant exposure, cleaning every 6 months is recommended.

Q: Is tap water or soapy water OK for PCB cleaning?

A: Avoid tap water due to mineral residues. Small amounts of mild detergent in
deionized water can aid aqueous cleaning.

Q: Which cleans better – acetone or isopropyl alcohol?

A: Acetone is a stronger solvent so it can remove some stubborn contaminants that


IPA cannot. However, acetone can damage component plastics.

Q: Is ultrasonic cleaning safe for all PCBs?

A: Ultrasonic cleaning is very effective but high ultrasonic vibrations can damage
fragile components in some boards.

Related Posts:

1. What Cleaner Can I Use to Clean Circuit Board?

2. How to Clean Circuit Board Corrosion

3. How to clean a circuit board without alcohol?

PCB Manufacturing & Assembly Services https://www.raypcb.com/


RAYMING PCB & ASSEMBLY

4. What Is Corroded PCB & How To Clean Corrosion Off A Printed Circuit
Board?

https://www.raypcb.com/clean-circuit-board/

PCB Manufacturing & Assembly Services https://www.raypcb.com/

You might also like