Machine Translated by Google
LYP-VGA-V2 Hardware Manual
Lingyi official technology forum: www.laser400.com
Version date illustrate
V1.0 2022/5/12 1. Add version number
2. Change the analog interface to red light interface
V1.1 2023/5/30 Perfect size picture
Machine Translated by Google
I. Overview
This laser marking machine board is a control card specially developed for laser marking machines. It supports fiber lasers, dioxygen
Carbon laser, YAG laser. This board has 24V related shutter signals, modulation signals, etc., which can
Directly connected to the relevant high-power laser. This board does not require an external PC and can be marked directly.
Machine Translated by Google
1.1 . Control card installation dimensions
2. Laser marking interface description
No. 1 Interface name Usage introduction
Power interface DC12~DC24V power is recommended to be 25W or above. Laser 24V
The signal needs to use 24V voltage
2 J3 interface: VGA interface VGA display signal output, connected to the display screen, it is recommended to use 18.5 inches
(1366*768) or 19 inches (1440*900).
3 CON3 interface: expansion IO interface, DB15 Used for auxiliary functions such as IO input and output, such as starting, stopping marking, missing printing
public seat Alarm, rotating axis and other functions
4 CON4 port: expansion IO interface 2 male ,
DB25 Used for auxiliary functions such as IO input and output, such as starting, stopping marking, missing printing
connector Alarm, rotating axis and other functions
5 P4 port: expansion IO interface part 2, 4p terminal An input IN1 port, an OC gate output OUT9 port
seat
6 P3 port: serial port, 5p terminal block Contains 2 serial ports for extended serial communication
7 RJ1 interface: network port Used for extended communication functions of the network
8ÿ USB_HOST1ÿUSB_HOST2 4 USB ports can connect U disk, mouse, keyboard, code scanner, etc.
USB host interface
9ÿ CON1 interface: galvanometer interface, DB15 socket is connected to a digital galvanometer with XY2-100 protocol
10. CON2 interface: laser interface, DB25 socket. Can be connected to fiber laser transmitter (Lianpin, Chuangxin), MOPA laser transmitter
device (Lianpin, Chuangxin), carbon dioxide laser emitter (Dawei), Rui
Fengheng YAG laser, etc.
Machine Translated by Google
11ÿ P1 interface: red light interface Used to connect red light, 5V output.
2.1. Power interface
Pin Signal name Specific instructions
1 24V 24V, positive power input
2 GND2 ground, negative input of power supply
3 ON Earth, for anti-interference
2.2. J3 interface: VGA interface
Standard VGA interface, use a standard VGA interface cable to connect the VGA interface to the display, and then the display can
The operating interface of the laser marking system is displayed on the display screen to realize the operation of the laser marking system.
2.3. CON3 interface: DB15 expansion IO port
This interface can be used for the input and output of the IO port to control the system marking.
Machine Translated by Google
Figure 5 Corresponding diagram of expanded IO interface
The specific description of each pin is as
follows: Signal name Specific instructions
Pin 1 IN4 24V optocoupler input 4, forming a loop with GND
2 OUT8 Configurable OC door output 8
3 OUT7 Configurable OC door output 7
4 5V 5V output, forming a loop with GND
5 24V 24V output, forming a loop with GND, this output is connected to the power
The input of the source is the same voltage
6 OUT5 Configurable TTL output 5
7 IN3 24V optocoupler input 3, forming a loop with GND
8 IN2 24V optocoupler input 2, forming a loop with GND
9 OUT4 Configurable TTL output 4
10 OUT3 Configurable TTL output port 3
11,12 13 GND land
OUT2 Configurable TTL output port 2
14 OUT6 Configurable OC door output 6
15 OUT1 Configurable TTL output 1
2.4. CON4 interface: DB25 expansion IO port
Machine Translated by Google
Pin 1, Signal name Specific instructions
17 2 24V 24V output
IN1 24V optocoupler input 1, forming a loop with GND
3 IN6 24V optocoupler input 6, forming a loop with GND
4 IN8 24V optocoupler input 8, forming a loop with GND
5, 9, 13 GND GND Ground
6 IN10 24V optocoupler input 10, forming a loop with GND
7 IN12 24V optocoupler input 12, forming a loop with GND
8 IN14 24V optocoupler input 14, which forms a loop with GND.
10 OUT10 Configurable TTL output port 10.
11 OUT12 Configurable TTL output port 12.
12 OUT14 Configurable TTL output port 14.
14 OUT9 Configurable OC output port 9, which forms a loop with 24V and can
be connected to an external relay.
15 IN5 24V optocoupler input 5, forming a loop with GND
16 IN7 24V optocoupler input 7, forming a loop with GND
18 IN9 24V optocoupler input 9, forming a loop with GND
19 IN11 24V optocoupler input 11, forming a loop with GND
20 IN13 24V optocoupler input 13, forming a loop with GND
21 IN15 24V optocoupler input 15, forming a loop with GND
22 5V 5V output
23 OUT11 Configurable TTL output port 11
24 OUT13 Configurable TTL output port 13
25 OUT15 Configurable TTL output port 15
Machine Translated by Google
2.5, P4 wiring port
Pin 1 Signal name Specific instructions
IN1 24V optocoupler input, forming a loop with GND
2 GND land
3 24V 24V power supply output
4 OUT9 OC gate output. Form a loop with 24V and GND
Note: This P4 interface shares part of the wiring of CON4 and is only for convenience of wiring.
2.6, P3: serial port
Pin Signal name Specific instructions
1 TXD3 Serial port 3 232 send
2 RXD3 Serial port 3 232 receive
3 GND land
Machine Translated by Google
4 TXD0 Serial port 0 232 send
5 RXD0 Serial port 0 232 receive
2.7, RJ1: network port
The network port is used for network expansion of the software.
2.8, USB_HOST1, USB_HOST2: USB interface
The USB interface is used to access mouse and keyboard operations and insert U disk, scanner gun, etc., and realize system files through U disk.
Import and export files, or update the system firmware through a USB flash drive.
2.9 , CON1 interface: DB15 galvanometer control
The galvanometer control signal is a digital signal and can be directly connected to a digital galvanometer with the protocol XY2-100. Notice:
It is recommended that digital signals be connected using shielded twisted pairs.
Figure 3 Corresponding diagram of the actual galvanometer interface
The specific description of each pin is as
follows: Pin Signal name Specific instructions
CLK-/CLK+ clock signal—/clock signal+
number SYNC-/SYNC+ Sync signal—/Sync signal+
1, 9 Xchannel-/ XChannel+ Galvanometer X signal—/Galvometer X signal+
2,10 Ychannel-/ YChannel+ Galvanometer Y signal—/Galvanometer Y signal+
3,11 4,12 5,13 NULL reserve
Machine Translated by Google
6,14 7 NULL reserve
NULL reserve
8,15 GND land
According to the above interface introduction, corresponding to the actual galvanometer interface line, connect to the corresponding pins of the galvanometer interface on the board.
Can.
2.10 , CON2 interface: DB25 laser control
The CON2 socket is specially used to connect the laser transmitter
Figure 4 Laser interface corresponding diagram
(1) Fiber laser wiring diagram
Pin number Signal name Specific instructions
1-8 P0-P7 Laser power. TTL output.
9 PLATCH Power latch signal. TTL output.
10,14 GND Control card reference location
11,12,16,21 LASERST0-3 Laser status input
17 VCC 5V power output of control card
18 MO Main oscillator switching signal. TTL output.
19 AP Power amplifier switching signal. TTL output.
20 PRR Repeating pulse frequency signal. TTL output
22 RedPt Red light indication. TTL output
23 EMSTOP Emergency stop switch signal. TTL output.
13,15,24,25 This pin is left floating and not connected.
Note: 1. Just connect the corresponding pins introduced above according to the actual laser wiring.
2. The above connection method is the connection method of fiber laser.
Machine Translated by Google
(2) CO2 laser wiring diagram
Pin number Signal name Specific instructions
19 AP(CO2_PWM+) CO2 laser pwm+ output. TTL output
10,14 17 GND Control card reference location
VCC 5V power output of control card
co2 laser waveform diagram
Note: Under normal circumstances, the carbon dioxide laser only needs a PWM signal, which is connected to pin 19 (PWM) of the laser interface on the marking card.
and 10 pins (GND).
Machine Translated by Google
(3) YAG laser wiring diagram
Pin number Signal name details
9, PLATCH(YAG_LASERO+) YAG laser switch signal+ (light gate signal
Number). TTL output
19 AP(YAG_PWM+) YAG laser pwm+ output. TTL output
10,14 17 GND Control card reference location
VCC 5V power output of control card
YAG laser waveform diagram
illustrate:
(1) Pin 19 is the YAG laser PWM+ signal. PWM+ corresponding to waveform diagram
Machine Translated by Google
(2) Pin 9 is the YAG laser gate signal +. LASERO+ corresponding to waveform graphs
Usually, the ultraviolet laser (YAG) can work as long as the enable signal EN (or gate) and PWM are enabled, that is, the wiring only needs to
Connect to pin 9 (EN or Gate), pin 19 (PWM) and pin 10 (GND) of the board's laser interface.
2.11 , P1 interface: red light interface
Pin number Signal name Specific instructions
9 NC No answer
8 NC No answer
7 NC No answer
6 REDLED Red light output, TTL output
5 GND land
4 NC No answer
3 NC No answer
2 NC No answer
1 NC No answer
3. Description of laser configurable input and output ports
Configurable input ports include: IN1~IN15
Configurable TTL output ports include: OUT1~OUT5, OUT10~OUT15
Configurable OC output port: OUT6~OUT8
Configurable OC relay output port: OUT9
3.1. Input port circuit
Machine Translated by Google
Recommended connection method:
3.3. OUT1 ~ OUT5, OUT10 ~ OUT15 output port circuit
OUT1 ~ OUT5 , OUT10 ~ OUT15 are TTL outputs
Note: Since OUT1 ~ OUT5, OUT10 ~ OUT15 are TTL outputs, you need to avoid grounding or short circuit, otherwise the board will be damaged.
3.4. OUT6 ~ OUT8 output port circuit
OUT6 ~ OUT8 are OC gate outputs
The circuit is as shown in the figure
These OC gate outputs can be combined with 5V to form a high drive capability output; they can also be combined with 24V to form a high drive capability output.
Machine Translated by Google
3.5. OUT9 output port circuit
OUT9 is the OC gate output circuit as
shown in the figure
When OUT9 uses inductive load output, such as relay, the following wiring is recommended
Software configuration
Note: The 24V voltage is the power input to the control board, so the voltage range selected by the relay should include the control board power supply voltage.
