Preface

With the increase of automobile demand in China, our automobile industry also experiences a rapid
development. The trucks including SUV, manufactured by Great Wall Motor Co., Ltd, which are sold all over
China, are in the leading place in terms of their sales volume, in order to satisfy the demands of various maintain-
ing staff, technicians and managing staff of Changcheng Co., Ltd, we compile this maintenance manual accord-
ing to the latest technological data. This manual covers six vehicle models including Deer, Safe, Sailor, Sing, So
Cool and Pegasus, its main content includes:
Part I is general introduction, which introduces the application index of this manual.
Part II introduces the chassis system, which mainly includes the technologies of dismantle, inspection,
adjustment, repairing, assembly and mount of the clutch, gear box, transfer box, drive shaft, suspension system
and automobile axle, braking system and steering system, etc. each operation approach is illustrated with figure,
which not only presents the maintenance procedure, but also clearly describes the technical requirements and
application limit.
Part III introduces the electric system and air-conditioning system of the automobile body, which mainly
covers such items as the location and content of protective box, power supply system, starting system, lighting
system, combination instrument, backup radar system, wiping and washing system, center control locking and
power window system, acoustical equipment system, full wire harness and air-conditioning system, etc. Electric-
ity diagrams for those electric systems are given in this manual so as to facilitate the maintaining technicians to
find out the problem easily and quickly.
Part IV introduces the external and internal body decoration, which mainly covers the dismantling, inspect-
ing and assembling requirements of the engine cover, front and rear doors, adhesive strip of body collision
avoidance, wheel shield, wrapping angle of wheel-shield and exterior trim panel, front and rear windshields,
side-window glass, rear-door glass, rear platform of cargo compartment, rear door, instrument panel, safety belt,
seat, tail-fin, luggage rack, and reserve tire bracket etc. The dimensions of vehicle body and frame are also given
to maintaining staff for reference during their repairing.
During the narrations of each part, items such as troubleshooting, maintenance notice, maintenance data
and application limit, fastening torques of bolts and nuts for special purpose, SST, SSM and lubricant materials
and so on are also introduced. Various maintenance data are briefed in attachment for reference.
Altogether, this manual is comprehensive in content, visual in illustration, clarifying in requirement and
plain in language. It can be referred by the maintaining staff, technicians and professional managing staff.
Even though we try our best to compile this manual in a strict earnest manner, we cannot guarantee that all
contents in this manual are correct. Therefore, users shall not put forward any claim with Great Wall Company
according to this manual; we are not in the position to hold the responsibility for the loss caused by usage of this
manual. Due to our limited knowledge, it is unavoidable to find error in this manual, any criticism and correction
from you is welcomed.
The final explanation power for this manual is subject to Great Wall Motor Co., Ltd
Compiler
May 2006
 Service manual for
chassis and body
General IN
Clutch CL
Gear box MT
Transfer box TF
Drive shaft PR
Suspension system and automobile axle SA
Braking system BR
Steering system SR
Body electric system BE
Air-conditioning system AC
Vehicle body BO
Maintenance and Up-keeping A
Special Tool B
 IN-1

Introduction
Page

How to use this manual ................................................. IN-2

Instruction for overall repairing ...................................... IN-4
Body lifting height and support position ........................ IN-5
fk
IN-2 Introduction
How to Use This Manual

How to use this manual

In order to help you to look in this manual, we marked the chapter
name and main theme at the top of each page.
In order to introduce the repairing items to you, we make the index on
the first page of each chapter, and notices need to be taken during all
repairing operation are also given in the related chapter.
Please read these notices carefully before the repairing work.
The troubleshooting form for each system will help you to diagnose
the system trouble and its cause.
We furnish with the repairing approaches for each possible cause in
the repairing approach column, which will help you to acquire the
solution in a short time.

Repairing approach
Most repairing operation can begin with referring to these illustrations.
These illustrations can help you identify the parts and their coordina-
tion situation

Example

snapping ring

oil seal-front semi-axle

front minor half-shaft
88

snapping ring

front speed reducer

and differential

N*m
specified torque front long

semi-axis

Parts that cannot be reused after being used
 Introduction
How to Use This Manual IN-3

Introductionóhow to use this manual

The repairing approaches are described step by step:

The illustrations show you what to do and at which position.

The theme of repairing operation tell you what you need to do.

The detailed instruction show you how to accomplish the repairing and
introduce to you other related affairs, such as specification, warning etc.
Example:
Topic:what to do ?

Check and adjust the flange bounce

PMãã (a) Attach the dial indicator seat to the reducer housing, and touch the
flange face with the measuring head of dial indicator, run the flange
and observe the pendular range of the indicator carefully.
Full bounce tolerance of face : 0.10mm

Specification Detailed introductionz;How to do?

This formula can help the experienced technicians find out the failure
causes in short time. Overhauling staff can browse the operation theme
and refer to the detailed description thereunder where necessary; impor-
tant specifications and warnings are written out in boldface.

Illustration: Specification
what to do and at which position The corresponding specifications are given in boldface in each repairing
approach of this manual, which allows the overhauling staff to check the
specification while keeping on repairing work.

Warning, Notice and Remark

Warning written out in boldface means there is possibility of self-
injury or harm to others.

Notice written out in boldface means there is possibility of damage
to parts under repairing.

Remarks singled out independently, but not in boldface, serve as
supplementary descriptions to help you accomplish the work more
efficiently.

Vehicle Code
There are six vehicle models in this manual, the model codes are as follows:
Deer model
Dr
Sailor model
SL
SO COOL model
SK
Safe model
SF
Sing model
SY
PEGASUS model
SJ

Abbreviation used in this manual

A/C
air-conditioner
ECU
electronic controller unit
SST
special service tool
2WD
two-wheel drive
4WD
four-wheel drive
IN-4 Introduction
Overall Repairing Rescription

Overall Repairing Description

1. Keep the vehicle clean and prevent it from e) Mount the cable terminal on the post with loosened nut, then
damage with guard plate, seat and floor cover fasten the nut. donít tap the terminal onto the post with
cloth. hammer.
2. Put down the dismantled parts in order during f) Be sure to check whether the cover of positive terminal (+) is
the dismantle process so as to facilitate the re- well located or not.
assembly
3. Observe the following items: 4. Check all hoses and wire plugs to verify whether they are
a) Disconnect the cable cathode from the connected solidly and correctly.
accumulator terminal before the electric 5. Parts that cannot be reused after being used.
operation;. a) The following parts should be changed with new one regularly:
b) Disconnect the cable from the cathode split pin, sealing washer, O-ring and oil seal, etc.
connected to the vehicle body when check- b) parts that cannot be reused after being used is marked with
ing or repairing the accumulator where
 in the element figure.
necessary. 6. Pre-coated parts
c) In order to avoid the damage of terminal The pre-coated parts including the bolt and nut are coated with
post of accumulator, loose the bolts first, locking seal glue in factory.
then pull up the cable vertically when a) In case the pre-coated parts are moved due to its fastening,
dismantling, don
t wring it or prize it. loosening or other causes, they must be coated again with the
d) Clean the terminal posts of the accumula- specified seal glue.
tor with dishcloth, and do not scrape them b) Coating procedure of pre-coated parts
with file or other similar tools to avoid 1) Clear away the former seal glue from the screw thread of
damage. the said parts.
2) Dry the parts with compressed air.
3) Coat the screw thread of the parts with the specified
locking seal glue.
tighten seal glue c) The pre-coated parts are marked with the
 in element
figure.
7. When necessary, sealing agent or sealing ring to prevent the
leakage.
8. Each specification shall be followed strictly. And the torque
spanners should be used.
9. Determine the necessity of using the special service tools (SST)
or special service materials (SSM) according to the real situation.
SST and SSM must be used where necessary and the repairing
should be in accordance with the repairing approach. SST list
and SSM list are attached to this manual.
10. Be sure to check whether the rated current of the new fuse is
correct when changing the fuse. The fuse rated current should
not larger than that of securing fitting and the fuse of smaller
rated current must not be used.
11. Be careful to hang or support the vehicle on the suitable place
when propping up or raising it.
a) In case prop up the vehicle at the front or back part, the wheels
must be blocked to guarantee the safety work.
 Introduction
Body Lifting Height and Supporting Position IN-5

b) The raised vehicle must be supported with the bracket; it is

dangerous to conduct the repairing work on the vehicle propped
up with one jack, even though such repairing can be finished in
short time.
12. The following items shall be taken notice to avoid the parts damage:
a) Do not open the covers of ECU and various computers where not
necessary absolutely. (if the IC terminal is touched, it be leaded
into static damage) .
b) Pull the hose at its ends when dismantling it, do not pull it at the
center section.
c) Pull the wire joint instead of the wire when pulling the joint
wrong correct
away.
d) Take notice to avoid of the drop of electric parts such as the
sensors or repeaters. In case those parts drop to the hard ground,
they must be changed instead of being reused.
e) Do not use the striking spanner to dismantle or mount the
thermostatic switch or thermostatic sensor.
f) Plug the needles of the multi-meter into the wire connector
carefully when checking its conductance and do not bend the
terminals.
g) Do not sheath the hose of the vacuum gauge into the very large
connector when using the gauge, instead, the stage joint shall be
used because once the hose expands, it is possible to lead into
the leakage.

Body lifting height and supporting position

front

123456
123456
123456
Jack lifting position ...........................................................................................................
123456
123456

Front......the front the beam center

Rear.....rear differential

Supporting position 12345

12345 12345
safety bracket .............................................................................................
12345
 CL-1

Clutch
Page

Troubleshooting .......................................................... CL-2

Inspection and adjustment of clutch pedal ................... CL-3
Air exhausting of clutch ................................................ CL-3
Clutch master cylinder ................................................ CL-4
Clutch wheel-brake cylinder ......................................... CL-6
Clutch cluster ............................................................... CL-7
CL
CL-2 Clutch
Troubleshooting

Troubleshooting
Trouble Causes Repairing approaches
Overlarge free stroke of clutch pedal Adjust the free stroke of pedal
There is air in clutch pipe Exhaust the air in clutch pipe
Failure of clutch brake-wheel cylinder Change the clutch brake-wheel cylinder
Difficulty in gearshift Failure of clutch master cylinder Change the master cylinder
or non-gearshift Overlarge clutch pendulum difference due to incorrect mounting, the Check the clutch rib
friction liner is stained with oil or is breaking
There is dirty or adhesive materials on spline of input shaft or clutch rib Repair according to requirement
Failure of clutch pressure plate Change the clutch pressure plate

Abrasion of clutch guide shaft Change the guide shaft

Insufficient free stroke of clutch pedal Adjust the free stroke of pedal
Disengagement of gear
The friction liner of clutch rib is stained with oil or is worn Check the clutch rib
box or clutch slip
Failure of clutch pressure plate Change the clutch pressure plate
Seize up of separation fork Check the separation fork

The friction liner of clutch rib is stained with oil or is worn Check the clutch rib
Clutch seize-up or
Failure of clutch pressure plate Change the clutch pressure plate
shaking
Looseness of engine seat Repair according to requirement

There is air in clutch pipe Exhaust the air in clutch pipe

Looseness of clutch
Failure of clutch brake-wheel cylinder Change the clutch brake-wheel cylinder
pedal
Failure of clutch master cylinder Change the master cylinder

Seize up of separation fork; Repair according to requirement

Abrasion or stained spot of separation bearing Change the separation bearing
Over-loud clutch noise
Abrasion of guide bearing Change the guide bearing
Parts looseness in clutch pressure plate Change the clutch pressure plate
Clutch
Inspection and Adjustment of Clutch Pedal, Air Exhausting of Clutch CL-3

Inspection on and adjustment

of clutch pedal
1. Check whether the pedal height is correct
Pedal height that begins from front wall board:
adjusting spot in Dr SF
(165
5)mm
pedal height SL SK SY SJ
(190-200)mm

2. Adjust the pedal height where necessary

pedal height
Loosen the locking nut and screw off the adjusting bolts until
the pedal height is correct. Then screw up the locking nut.
Pedal free stroke

3. Check whether the pedal free stroke is correct

Press the pedal lightly until the resistance generated by clutch
occurs.
pedal free stroke: (5-15)mm

4. Adjust the pedal free stroke where necessary;

a) Loosen the locking nut and rotate the push-rod until the
stroke is correct;
b) Screw up the locking nuts;
pedal free stroke
c) Check the pedal height after the adjustment of pedal free
stroke.

Air-exhausting of clutch
Remark: in case operation needs to be conducted for the clutch
system or if there is air in clutch, exhaust the air.
Notice : Do not stain the painted surface with brake liquid,
if any brake liquid is left, wash it away immediately.

1. Fill the brake liquid into the oil cup of clutch master cylinder;
The oil cup of master cylinder shall often be checked and, if
necessary, added with brake liquid.

2. Connect the ethene resin pipe to the air-exhausting valve.

Insert the other end of the pipe into the container, half of which
is filled with brake liquid.

3. Air-exhausting in clutch system

a) Move the clutch pedal up and down slowly for several times.
b) Loosen the air-exhausting valve when pressing the pedal
increasingly until there is brake liquid overflowing, then
tighten the air-exhausting valve.
c) Repeat this operation until the bubble in brake liquid disappears.
CL-4 Clutch
Clutch Master Cylinder

Clutch Master Cylinder

Element drawing

oil cup of clutch master cylinder

spring pin with groove

ring pipe

piston
spring
clutch master
cylinder
18
2
19
1 nut open pin of nut
open ring

push-rod

U-clamp pin

dust cover
gasket

N*m
specified torque

Parts that cannot be reused after using.

Disassembly of master cylinder

1. Tear down the pin of push-rod

SST 2. Tear down the clutch pipe

Disconnect the jointed pipe nuts with SST

3. Tear down the master cylinder

a) Tear down the fixing nuts;
b) Pull out the master cylinder.
Clutch
Clutch Master Cylinder CL-5

Disassembly of oil cup of master cylinder

1. Tear down the oil cup
a) Use the pinch and hammer to tap out the spring pin with
groove;
b) Tear down the oil cup and ring pipe.

Assembly of master cylinder

1. Mount the oil cup
a) Mount the oil cup and the new ring pipe.
b) Use the pinch and hammer to tap in the spring pin with
groove.

Mount of master cylinder

1. Mount the master cylinder
Mount the fixing nuts and screw them up.

2. Connect the clutch pipes;

Connect the clutch pipes with SST

3. Connect the push-rod and mount the pin;

Encase the pin of push-rod with clamping pliers.

4. Exhaust the air in clutch system and adjust the clutch

pedal.
CL-6 Clutch
Clutch Brake-Wheel Cylinder

Clutch brake-wheel cylinder

Element drawing

air-exhausting plug

clutch brake-wheel cylinder

18
2
19
1

push-rod
piston dust cover
spring

N*m
specified torque

Disassembly of brake-wheel cylinder

1. Tear down the clutch pipeline.
Remove the pipeline with SST

2. Tear down the two bolts to take down the clutch

brake-wheel cylinder

mount of brake-wheel cylinder

1. Mount the brake-wheel cylinder with two bolts;

2. Connect the clutch pipeline;

Connect the pipeline with SST;

3. Exhaust the air in clutch system.

 Clutch
Clutch Cluster CL-7

Clutch cluster
Element drawing
flywheel

clutch rib

clutch pressure plate 30

clamp separation fork

dust cover

separation
N*m
specified torque bearing

Disassembly of clutch cluster

1. Tear down the gear box;
Remark: do not leave the gear oil in drying

2. Tear down the clutch pressure plate and the clutch rib
a) Make aligning marks on the clutch pressure plate and the
flywheel.
b) Loosen the fixing bolts gradually until the spring tension
is released;
c) Tear down the fixing bolts to pull out the clutch pressure
plate and clutch rib.

3. Tear down the bearing and separation fork from the gear
box;
a) Tear down the clamp to pull out the bearing;
b) Tear down the separation fork and dust cover.
CL-8 Clutch
Clutch Cluster

Inspection on clutch parts

1. Check whether there is abrasion or damage of clutch rib;
Measure the depth of the rivet head with calipers.
Min depth of rivet head: 0.3mm
If the depth of rivet head exceeds the limit value, change the
clutch rib.

2. Check the radial pendulum difference of the clutch

Check the radial pendulum difference of the clutch rib with
multi-meter.
Max radial pendulum difference: 0.8mm
If the radial pendulum difference exceeds the max value,
change the clutch rib.

3. measure the rdial pendulum difference of the flywheel;

Check the radial pendulum difference of flywheel with multi-
meter;
Max radial pendulum difference: 0.2mm
If the radial pendulum difference exceeds the max value,
change the flywheel.

4. Check the guide bearing

Exert the force in radial direction to rotate the bearing by hand.
If the guide bearing doesn
t run or if there is great resistance,
change the guide bearing.
Remark: as this bearing is lubricated permanently, it needs not
to be cleaned or lubricated.

5. Change the guide bearing where necessary.

a) Tear down the guide bearing with SST;
SST
 Clutch
Clutch cluster CL-9

b) Mount the guide bearing with SST.

Remark: the bearing shall be verified in good running after it
SST
is encased in the flywheel hub.

2. Check whether there is abrasion on the diaphragm spring.

Check the abrasion depth and width of diaphragm spring with
calipers.
Limit value: Max depth: 0.6mm
Max width: 5mm
If the abrasion depth or width of the diaphragm spring exceeds
the limit value, change the diaphragm spring .

3. Check the separation bearing

Exert force in radial direction by hand to rotate the bearing.
If it cannot be rotated or if the resistance is too large, change
the separation bearing.
Remark:
Remark: as this bearing is lubricated permanently, it doesnít
need to be cleaned or lubricated.

SST
Mount of clutch cluster
1. Mount the clutch rib on flywheel;
Mount the clutch rib on flywheel with SST.

flywheel side

2. Mount the clutch pressure plate

a) Align the marks on clutch pressure plate and that on flywheel;
alignment b) Screw up the bolts in even manner around the clutch pressure
mark
plate until pressure plate and the flywheel contact closely,
then tighten the bolts.
Tightening moment: 30 N
m
Remark: tighten the uppermost bolt of the three that is near to
the locating pin.
CL-10 Clutch
Clutch Cluster

3. Check the alignment of the diaphragm spring end.

Check the alignment of diaphragm spring end with SST.
Max dislocation: 0.5mm
if the difference is more than the specified value, adjust the
alignment of diaphragm spring end with SST.

SST

4. Coat the lithium base grease;

Coat the lithium base grease on the following parts:

Contact spot of separation fork and bearing

Contact spot of separation fork and push-rod;

Support spots of separation fork

Spline of clutch rib

5. Encase the dust cover, separation fork, separation bearing

seat and bearing into the gearbox;

6. Mount the gearbox.

 MT-1

Gear box
page

Notice ........................................................................... MT-2

Troubleshooting ........................................................... MT-3
Dismantle of Gear Box ................................................. MT-4
Mount of Gear Box ....................................................... MT-7
Disassembly of Gear Box ............................................. MT-10
Input Shaft Assembly ................................................... MT-18
Element Drawing ...................................................... MT-18 MT
Inspection on Synchronizing Ring ............................ MT-18
Bearing Change ....................................................... MT-18
Output Shaft Assembly ................................................. MT-20
Element Drawing ...................................................... MT-20
Disassembly of Output Shaft Assembly.................... MT-21
Inspection on Output Shaft Assembly ...................... MT-23
assembly of Output Shaft Assembly ......................... MT-25
Countershaft Assembly And Reverse Idle Gear
Assembly ...................................................................... MT-29
Element Drawing ...................................................... MT-29
Disassembly Inspection and Assembly of
Countershaft Assembly ............................................. MT-29
Assembly of Reverse Gear ...................................... MT-31
Rear Housing assembly ............................................... MT-33
Element Drawing ...................................................... MT-33
Change of Oil Seal ................................................... MT-33
Change of Shaft Bush .............................................. MT-33
Inspection on and change of Position-Limit
Mechanism Cluster ................................................... MT-34
Front Cover of Bearing ................................................. MT-36
Element Drawing ...................................................... MT-36
Change of Oil Seal ................................................... MT-36
Assembly of Gear Box ................................................. MT-37
MT-2 Gear Box
Notice

Notice
Notice for disassembly and assembly of gearbox
Notice shall be taken during the gear disassembly and assembly on the soft handle for the parts, especially
for the coupling faces so as to avoid the collision; each part shall be put down in order to avoid the missing
or mistaking.
Notice shall not only be taken in the aforesaid aspects, but also in the following items
1. Wash all parts before assembly (rubber fittings and washers excluded).
2. Various oil seals, retainer rings for shafts, spring-type pins shall not be reused.
3. Lubricating oil shall be coated on the friction surfaces, and lubricating grease shall be coated on the lips
of oil seals.
4. Rolling elements shall not be used to transfer the pressure during the various bearing assembly.
5. Lip-type oil seal must not be sloping when assembling it.
6. The openness at the two ends of the spring collar shall be misfit when assembling the component
elements of the synchronizing instrument, and
7. No part is allowed to leak the lubricating oil when the gearbox locating at its working place.
 Gear Box
Troubleshooting MT-3

Troubleshooting
Common Failures Causes Methods for troubleshooting
Difficulty in gear engagement Non-use of clutch Use the right driving approach
Non-full separation of clutch Checking for adjustment
Severely warned tooth rings of synchronizing Change
fittings
Over-hard locating spring Change

Over-loud or abnormal noise Over-low oil level Add oil to the specified level
Lubricating oil of inferior quality Change it with the specified oil
Non-timely oil change Change the oil and damaged parts
Unsuitable axial location or clearance of gears Check for adjustment
Bearing damage Change
Burr or collision on gear Repair or change the gear

Oil leakage, oil penetration Oil added above the specified level Adjust oil to the given level
Loss or missing of bolts Reassembling or fasten the bolt according to
the specified torque
Vent plug trouble Change
Sealing element damage Change

Damage of synchronizer Overexert in gear shift Change

Non-use of clutch Use the right driving approach
Damage on spring collar of synchronizer Change
Incorrect mounting of drive shaft Check for adjustment

Non-engagement of gear Trouble in controlling mechanism Check for adjustment

Incorrect assembling the locating spring or Reassembly
steel ball
Invalidation of locating spring Change
Severely worn gear sleeve or fork groove Change
Seriously worn toggle fork Change

Burning bearing, burning gear Over-low oil level Change damaged parts and add oil
Inferior lubricating grease Change the damaged parts and lubricating oil
Non-timely oil change, over-dirty oil Change damaged parts and lubricating oil
Inter-use of differential oil or usage of Change damaged parts and lubricating oil
additive

Difficult in gear disengagement Spring invalidation of synchronizer Change

Warn inner groove of tooth ring of synchronizer Change
Tooth ring of synchronizer choked on conical Change
face
Toggle fork deformation or toggle fork axle Change
deformation
Severely worn toggle fork Change
MT-4 Gearbox
Dismantle of Gear Box

Dismantle of gearbox
1. Disconnect the cathode wire from the cathode of storage
cell.

2. Tear down the setting bolts of fan cover.

Tear down 4

3. Tear down the shifting ball of gear change lever

Loose the locking nuts by dextroroting the ball.

4. Tear down the glove box

Dismantle the four bolts of the glove box and put the glove box
into the suitable place.

5. Tear down the dust cover.

6. Tear down the gear change lever.
7. Raise the vehicle to discharge the oil in gearbox.
Warning: the reliability of vehicle shall be verified.
8. Tear down the drive shaft.
(See page PR-5)
9. Tear down the odometer sensor and the plugging
elements of backup switch

10. Tear down the vent pipe.

Tear down the heading exhaust pipe from branch exhaust pipe
 Gearbox
Dismantle of Gear Box MT-5

11. Tear down the wheel-brake cylinder of clutch.

(a) Dismantle the setting bolts of the wheel-brake cylinder of
clutch with spanner.
(b) Hang the wheel-brake cylinder with a thread on the side
of engine without oscillation.
Remark: Do not disconnect the pipeline of the wheel-brake
cylinder.

12. Tear down the pawl washer and bracket of the rear part
of gearbox:
Two-wheel driving:
(a) Dismantle the four bracket bolts (skip over this process
for the wielding structure).
(b) Lift the engine with jack to raise the gearbox a little.

(c) Dismantle the pawl washer from the rear part of gearbox.

Four-wheel driving:
4WD
Dismantle the bolts from the pawl washer and bracket of the
rear part of gearbox to tear down the pawl washer and bracket.

13. Insert the wooden plate between the bottom frame and
the beam.
MT-6 Gearbox
Dismantle of Gear Box

4WD 14. Dismantle the eight bolts that fasten the beam of gearbox.

15. Tear down the starter

Put the starter on the side of engine.

16. Dismantle the bolts of clutch frame and bracket (wrapping

angle).

17. Tear down the remaining bolts of gear box

18. Tear down the gear box

(a) Pull out the gear box in backward direction;
(b) Put down the engine at the front and tear down the
gearbox from the vehicle.
Notice: be careful not to damage the dust cover of
expansion shell.
Gear Box
Mount of Gear Box MT-7

Mount of gear box

1. Put down the gearbox at the mounting place.
2. Mount the bolts of gearbox, clutch bracket and starter.
Tightening moment:
(a) Setting bolt of gear box (82
10)N
m
(b) Enforcement plate bolt (37
5)N
m
(c) starter bolt (39
5)N
m

Notice: the bolts of gear box and clutch shall be mounted

with the clutch pipe clip together.

3. Mount the pawl washer and bracket of gearbox

Two-gear driving:
(a) Mount the gearbox pawl washer and fasten the relative
bolts.
Tightening moment: 23
3)N
m
(b) Lift the rear part of engine with jack and wooden block so
that the gearbox is raised a little.

(c) Mount the bracket of gear box on beam and fasten the
relevant bolts (this process may skip over in wielding
structure)
Tightening moment
(23
3)N
m

(d) Connect the gearbox bracket and supporter with bolts,

then tighten the bolts.
Tightening moment: (23
3)N
m
MT-8 Gear Box
Mount of Gear Box

4WD 4WD:
(a) Mount the bracket and supporter of leg washers of rear
engine in 4WD vehicle;(SF)

4WD (b) Mount and tighten the third beam of 4WD vehicle. (SF)

4. Remove the wooden spill.

5. Mount exhaust pipe.

Mount the exhaust pipe on the branch exhaust pipe.
Tightening moment
(62
3)N
m

6. Mount the wheel-brake cylinder of clutch.

Tightening moment
(18
2)N
m
7. Mount odometer sensor and plugging elements of backup
switch.
8. Connect the drive shaft.
(See page PR-12)
9. Add oil into the gearbox.
Lubricating oil grade: GL-5 85W/90
Volume: 2.4L(dry)
Remark: the Tightening moment of oil filling/draining
plug: (30
50)N
m
Gear Box
Mount of Gear Box MT-9

10. Drop the vehicle.

11. Mount the dust cover and gear change lever.

12. Mount storage box.

13. Mount the manual ball, and

14. Mount the fan cover and fasten the bolts.

Mount on them and screw up the four bolts.
15. Connect the cell cable to the cathode of storage cell; and
16. Conduct the load test
Check whether there is abnormal noise and whether the
operation is stable.
MT-10 Gearbox
Disassembly of Gear Box

Disassembly of Gear Box

1. Tear down the separation toggle fork and separation
bearing.
2. Tear down the backup switch, the driven gear of
speedometer.
3. Tear down the clutch from the gearbox frame.
Take apart the nine boits.

4. Tear down bolts of locating spring of the five-speed

toggle fork, locating spring and locking ball.
(a) Dismantle the bolts from the rear cover with the torque
socket spanner.
(b) Take out the spring and locking ball with magnetic rod.

5. Tear down the operating seat of gear change lever.

(a) Dismantle the setting bolts of the operating seat of gear
change lever.
(b) Take away the operating seat lightly and put it at the
suitable place.

6. Tear down axial locating pin assembly of shifting gear.

7. Tear down the fastening nuts of extension frame.

(a) Tear down the fixing bolts of gearshift shaft.
(b) Tear down the fastening nuts of expansion shell.
 Gearbox
Disassembly of Gear Box MT-11

4WD (c) Dismantle the nuts of the four-gear driven extension fram.

(d) Tap the extension frame lightly with rubber hammer to tear
down the selective gearshift shaft and selective rocker
arm.

8. Tear down front cover.

Dismantle the eight bolts and front cover and axial oil seal.

9. Tear down the input shaft, axial/bearing open ring and

countershaft bearing open ring.

10. Dismantle the gearbox frame from the central link plate,
(a) Put the gearbox straightly as shown in the drawing.
(b) Tap out the gearbox frame out carefully with the rubber
hammer. And
(c) Pull out the gearbox frame out from the central link plate
as the drawing shows
MT-12 Gearbox
Disassembly of Gear Box

11. Grip the central link plate in the table vice,

(a) Use two clutch bolts, washers and suitable nuts as shown
in the drawing.
Remark: mount the washer in the reverse direction, increase
and decrease the washer quantity to flush the bolts terminal
with the external face of the washer.
(b) Grip the central link plate in the table vice.

12. Tear down the locating spring bolts, locating spring and
locking ball,
(a) Dismantle each locating spring bolts with the torque socket
spanner.

(b) Take out the toggle fork axles of the first, second, third,
fourth and reverse as well as the axial locating spring and
locking ball of the fifth-gear toggle fork.

13. Tear down the axial retainer ring of the gearshift fork
Tap the axial retainer ring of gearshift fork lightly with two
screwdrivers and one hammer.
Gearbox
Disassembly of Gear Box MT-13

14. Tear down the five-speed gearshift toggle fork,

(a) Punch out the spring pin with impact head and hammer.

(b) Tap the five-speed gearshift fork until take it out.

Notice: It must be the neutral location this time.

15. Tear down the guiding module of the five-speed gear-

shift and five-speed reverse shift fork axle.
(a) Take out the inter-locking steel ball from the guiding
module of the fifth reverse shift-shaft.

(b) Tear down the fifth reverse shift guiding module and fifth
reverse shift fork axle.

16. Take out the five-speed gearshift fork axle

MT-14 Gearbox
Disassembly of Gear Box

17. Tear down the reverse shift fork axle, reverse rocker
arm, reverse toggle lever and toggle block
(a) Tap out the spring pin with the nail punch and hammer.

(b) Take out the interlocking ball and interlocking guidepost

between the reverse shift fork axle and the five-speed
gearshift fork axle.
(c) Tear down the reverse shift fork axle, and
(d) Tear down the reverse rocker arm and yoke block.

18. Tear down the first-second-speed gearshift fork axle.

(a) Take out the interlock pin and interlock guide post between
the reverse shift fork axle and the five-speed gearshift fork
axle.

(b) Dismantle the locating bolts of the toggle fork of the first-
second-speed gearshift toggle fork.

(c) Dismantle the fork axis of the first-second-speed gearshift.

(d) Take out the short interlock pin between the first-second-
speed gearshift fork axle and the third-fourth-speed gear-
shift fork axle
Gearbox
Disassembly of Gear Box MT-15

19. Tear down the third-fourth-speed gearshift fork axle and

the toggle forks of first-second speed gear and third-
fourth speed gear.
(a) Tap out the spring pin with the nail punch and hammer.

(b) Tear down the toggle forks of the third-fourth and first-
second-speed gearshift.

20. Tear down the coupling gear, synchronizer, gear cluster,

thrust washer and needle bearing of the five-speed
gearshift
(a) Tap down the retainer ring of the rear countershaft with
two screwdrivers and one hammer.

(b) Tear down the synchronizer assembly, coupling gear and

gear cluster of the five-speed gearshift. And
(c) Dismantle the five-speed needle bearing.

21. Tear down the thrust washer and five-speed lock ball.
(a) Tear down the thrust washer of five-speed gear.
(b) Take out the lock ball with magnetic rod.
MT-16 Gearbox
Disassembly of Gear Box

22. Tear down the reverse rocker arm bracket

Dismantle the two bolts and the reverse rocker arm bracket.

23. Tear down the reverse idle gear and reverse idle gear
axle
(a) Dismantle the setting bolts of idle gear and the pressing
plate of reverse idle gear axle.

(b) Dismantle the reverse idle gear and the reverse idle gear
shaft.

24. Take down the bearing baffle of the output shaft.

(a) Dismantle the four bolts with torque socket spanner.
(b) Take down the bearing baffle of the output shaft.

25. Dismantle the intermediate-gear shaft.

(a) Pry out the split ring of the rear bearing of the intermediate-
gear shaft with the split-ring-type pliers.
 Gearbox
Disassembly of Gear Box MT-17

(b) Taker apart the rear bearing of intermediate shaft with

SST
SST tool and wrench.

(c) Take down the intermediate shaft.

26. Tear down the input shaft

Tear down the bearing with 13 needles and synchronizing ring
from the input shaft.

27. Tear down the output shaft

(a) Dismantle the stop ring from the output bearing with split-
ring-type pliers.

(b) Tap lightly the central link plate with rubber hammer while
pulling the output shaft manually to tear down the output
shaft.

28. Check the back-up lamp switch

Check the terminal connection, when the switch is pressed
down, as shown in the drawing, it is connected, otherwise is
disconnected, in case the switch is not in conformity with this,
it shall be changed.

push down
to close
MT-18 Gearbox
Input Shaft Assembly (Element Drawing, Inspection On Synchronizing Ring, and BearingChange)

Input Shaft Assembly

element drawing

input shaft needle bearing

bearing
bearing stop ring

retainer ring

synchronizing ring

Inspection on Synchronizing Ring

1. Run the synchronizing ring and put it into the assembly
to check its stopping performance

2. Check the clearance between the rear face of

synchronizing ring and the gear.
Standard clearance:
Tung tooth
(1
1.6)mm
Upper tooth
(1.5
1.8)mm
Limit clearance
0.8mm

Bearing Change
1. Tear down the input shaft bearing with the pressure
machine.
Gearbox
Input Shaft Assembly (Bearing Change) MT-19

2. Mount the new bearing with pressure machine and SST.

3. Select the retainer ring to obtain the minimum axial clearance

ppq

4. Mount the retainer ring with the split-ring-type pliers.

5. Mount the retainer ring with the split-ring-type pliers.

MT-20 Transmission
Output Shaft Assembly (Components Figure)

Output shaft assembly

Components figure

3th,4th gear synchronizer

synchronizer meshing sleeve 3th gear needle bearing
slide block

synchronizer spring
expansion ring

gear components of 3rd gear

steel ball
toothed ring of
steel ball
synchronizer
snap ring

synchronizer hub of 3rd

and 4th gear
output shaft

synchronizer meshing sleeve 1st gear shaft sleeve

of 1st and 2nd gear locking ring of output
shaft rear bearing
gear components
synchronizer sliding block of 1st gear

spring expansion ring

needle bearing of
2nd gear

rear bearing of
output shaft
needle bearing of 1st gear

toothed ring of synchro-

nizer for 1st and 2nd gear

toothed ring of synchronizer

gear components for 1st and 2nd gear
of 2th gear drive gear snap ring of odometer

odometer drive gear

gear of 5th gear snap ring of 5th gear

Transmission
Output Shaft Assembly(Disassembly of Output Shaft Assembly) MT-21

Disassembly of output shaft assembly

1. Remove the drive gear of speedometer
(a) Pry down the two shield rings with open end ring plier
(b) Dismantle the drive gear of tachometer.
(c) Take out the steel ball with magnetic stick.

2. Remove the 5th gear,rear bearing of output shaft,1st

gear assembly,1st gear shaft sleeve and needle bearing
of 1st gear
(a) Take down the circlip of 5th gear with two screwdrivers
and one hammer.
(b) Dismantle the rear bearing of output shaft,1st gear assem-
bly and 1st gear sleeve with press machine.
(c) Remove the needle bearing of 1st gear.
3. Remove the synchronized ring

4. Take down the steel ball

Take out the steel ball with magnetic rod.

5. Take down the 1st and 2nd gear synchronizer assembly,

2nd gear assembly,and 2nd gear needle bearing.
(a) Remove the 1st and 2nd synchronizer assembly and 2nd
gear components.
(b) Take off the needle bearing of the 2nd gear.

6. Take down the meshing sleeve ,sliding block and spring.

Remove the three sliding blocks and two springs from the
synchronizer assembly with one screwdriver.
MT-22 Transmission
Output Shaft Assembly(Disassembly of Output Shaft Assembly)

7. Take down the 3rd and 4th gear synchronizer assembly,

3rd gear and needle bearing .
(a) Remove the snap ring with plier for snap ring.
(b) Take down the 3rd and 4th gear synchronizer assembly and
3rd gear with press machine.
(c) Remove the needle bearing .

8. Take off the meshing sleeve ,sliding block and spring

from 3rd and 4th synchronizer.
Remove the three sliding blocks and spring from the meshing
sleeve with one screwdriver.
 Transmission
Output Shaft Assembly(Inspection of Output Shaft Assembly) MT-23

3rd gear position Inspection of output shaft assembly

1. Check the axial clearance of every gear:
For the transmission made by Shang Chi:(0.15
0.33)
mm(1st,2nd,and 3rd gear position)
For the transmission made by Tang Chi:(0.1
0.25)mm
(1st gear position)(0.09
0.26)mm,(2nd and 3rd gear
position)
1st gear position 2nd gear position

2. Measure the idle clearance of every gear.

Check the radial clearance of every gear with micrometer.
Standard clearance:
For the transmission made by Shang Chi:0.05mm
(1st,2nd,and 3rd gear position)
For the transmission made by Tang Chi:
(0.009
0.033)mm(2nd and 3rd gear position)
(0.009
0.032)mm(1st gear position)
Max clearance

For the transmission made by Shang Chi:0.05mm
For the transmission made by Tang Chi:0.033mm
(2nd,and 3rd gear position);0.032(1st gear position)
If the clearance value exceeds the limit above , the gear,
needle bearing or shaft should be changed.

PK Inspection for output shaft and 1st gear shaft sleeve

(a) Measure the thickness of output shaft flange with callipers
Min thickness

For the transmission made by Shang Chi:4.75mm
For the transmission made by Tang Chi:4.65mm

(b) Measure the thickness of flange of 1st gear shaft sleeve

with callipers
Min thickness

For the transmission made by Shang Chi:3.87mm
For the transmission made by Tang Chi:3.795mm

(c) Measure the outside diameter of the journal of output shaft

with micrometer.
Min diameter:19.216mm
Gear of 2nd gear:37.984mm
Gear of 3rd gear:34.984mm
MT-24 Transmission
Output Shaft Assembly(Inspection of Output Shaft Assembly)

(d) Measure the outside diameter of the gear sleeve of 1st gear
with micrometer.
Min diameter:38.984mm.

(e) Measure the radial run out torlerance of the shaft with
micrometer.
Max radial run out torlerance

For the transmission made by Shang Chi:0.015mm
For the transmission made by Tang Chi:0.05mm

4. Check the synchronized ring

(a) Turn the ring ,and put it into to check the brake action.

(b) Measure the gap between the rear of the synchronized ring
and gear end.
Standard clearance:
For the transmission made by Shang Chi:(1.5
1.8)mm
For the transmission made by Tang Chi:(1.2
0.4)mm
Limit clearance:0.8mm

5. Measure the clearance between the gear shifting fork

and meshing sleeve
Check the clearance between the gear sleeve and gear shifting
fork with feeler gauge.
Max clearance

For the transmission made by Shang Chi: 0.54mm
For the transmission made by Tang Chi: 0.7mm
 Transmission
Output Shaft Assembly(Assembly of Output Shaft Assembly) MT-25

3/4 gear posititon 1/2gear posititon Assembly of output shaft assembly

1. Assembly of synchronizer
(a) Insert the synchronizer hub and sliding block into the gear
front
sleeve.

(b) Install the spring expansion ring under the sliding block.
Note:The openings of spring expansion ring should be
staggered during installation .
front side

2. Install the gear components of 3rd gear and synchronizer

of 3rd and 4th gear on the output shaft.
(a) Smear the gear oil on the shaft and the needle bearing of
3rd gear.
(b) Put the synchronized ring on the components of gear of 3rd
gear, and align the notch of synchronized ring and sliding
block.
(c) Install the needle bearing into gear components of 3rd gear.

(d) Assembly the gear components of 3rd gear and synchro-

nizer of 3rd and 4th gear with pressing machine.

3. Assembly of snap ring for shaft

To choose one snap ring which make the axial clearance be
Min, and install it on the shaft.
MT-26 Transmission
Output Shaft Assembly(Assembly of Output Shaft Assembly)

Standard clearance:
For the transmission made by Shang Chi
(0.15
0.33)mm
For the transmission made by Tang Chi:
(0.09
0.33)mm

5. Assembly for the gear components of 2nd and

synchronizer of 1st and 2nd gear
(a) Smear the gear oil on the needle bearing of gear of 2nd
gear.
(b) Put the synchronized ring on the gear,and align the notch
and shift key.
(c) Install the needle bearing into the gear components of 2nd
gear.

(d) Assembly the gear components of 2nd gear and meshing

sleeve of synchronzer of 1st and 2nd gear with pressing
machine.

6. Check the axial clearance of gear components of 2nd

gear
Measure the axial clearance of gear components of 2nd gear
with feeler gauge.
Standard clearance:
For the transmission made by Shang Chi:(0.15
0.33)mm
For the transmission made by Tang Chi:(0.09
0.33)mm

7. Assembly the locking ball and gear components of 1st

gear
(a) Install the locking ball into the shaft.
Transmissio
Output Shaft Assembly(Assembly of Output Shaft Assembly) MT-27

(b) Smear the gear oil on the needle bearing of gear of 1st gear.
(c) Assembly the gear components of 1st gear,synchronized
ring,needle bearing and sleeve of gear of 1st gear.
(d) Install the assembly on the output shaft,and align the notch
of synchronized ring and sliding block .
(e) Turn the sleeve of 1st gear shaft to align the it with the
locking ball.

8. Installation for rear bearing of output shaft

Fix the bearing of output shaft to the output shaft with SST and
pressing machine, make the notch of locking ring of output
shaft rear bearing expose to the tail.
Remark: Hold the sleeve of gear of 1st gear and don

t let it fall
off.
SST

9. Install the gear of 5th gear

Fix the gear of 5th gear with SST and pressing machine.

SST

10. Assembly the snap ring of shaft

(a) To choose one snap ring which make the axial clearance
be Min, and install it on the shaft.
Max clearance
0.1mm

(b) Knock the snap ring of shaft of 5th gear tightly with
screwdriver and hammer.

11. Measure the axial clearance of gear of 1st gear

Measure the axial clearance of gear of 1st gear with feeler
gauge
Standard clearance:
For the transmission made by Shang Chi:(0.15
0.33)mm
For the transmission made by Tang Chi:(0.09
0.33)mm
MT-28 Transmission
Output Shaft Assembly(Installation of Output Shaft Assembly)

12. Fix the drive gear of speedometer

(a) Install the locking ball and drive gear.
(b) Install the drive gear of tachometer with plier for shaft
shield ring
Gear Box
Countershaft Assembly and Reverse Idle Gear Assembly (Element Drawing, Countershaft Assembly Disassembly, Testing and Assembly) MT-29

Countershaft Assembly and Reverse Idle Gear Assembly

Element drawing

rear bearing of stop ring of the rear bearing

stop ring for front bearing countershaft of countershaft
of countershaft intermediate-gear shaft
steel ball
front bearing of reverse idle
countershaft gear shaft
reverse idle gear
cluster

axial pressing plate

sliding block of for reverse idle gear
retainer ring for front synchronize
engagement sleeve of the
countershaft
five-speed synchronizer

five-speed needle
bearing

synchronizer tooth
spring collar of spring collar
five-speed thrust washer
coupling gear around
five-speed cluster the five-speed gear

Disassembly, Testing and Assembly of

Countershaft
1. Tear down the coupling gear, sliding block and the five-
speed spring collar.
Tear down the coupling collar, three sliding blocks and the two
five-speed spring collars with screwdriver.

2. Measure the radial clearance of the reverse idle gear

with dial gauge
Standard clearance:
Shang chi:0.05mm
Tang chi:(0.10~0.30)mm (Tang chi is the close Spline
match, which belongs to radial clearance)
Max clearanle:
Shang chi:0.05mm
Tang chi:(0.10~0.30)mm (Tang chi is the close spline
match, which belongs to radial clearance)
MT-30 Gear Box
Countershaft Assembly and Reverse Idle Gear Assembly ( Countershaft Assembly Disassembly, Testing and Assembly)

3. Reverse gear inspection

Measure the diameter of needle bearing with micrometer.
Standard diameter

Shang Chi
26.000mm
Tang Chi
(25.98
26.00)
Limit Diameter

Shang Chi
25.984mm
Tang Chi
25.86mm

4. Check the synchronizing ring

(a) Run the retainer ring for shaft and put it onto the shaft to
check itsstopping performance

(b) Measure the clearance between the rear section of the

synchronizing ring and the spline.
Standard clearance:
Shang Chi
(1.5
1.8)mm
Tang Chi
(1
2)mm
Limit clearance: 0.8mm

5. Measure the clearance of the shift fork and gear sleeve.

Test the clearance of the shift fork and gear sleeve with the
feeler gauge.
Max clearance:
Shang Chi: 0.54mm
Tang Chi:1.0mm

6. Change the bearing

The front bearing of the reverse gear shall be changed when
necessary
(a) Pry down the retainer ring for shaft with a split-ring-type
pliers.
 Gear Box
Counter Shaft Assembly and Reverse Idle Gear Assembly (Assembly of Reverse Gear Assembly) MT-31

(b) Press out the bearing with SST.

SST

(c) Press in the bearing, side race and inner race with the
sleeve wrench
socket spanner.

(d) Select the split ring that leave the radial clearance to
minimum level, and mount it on the shaft.

7. Mount the engagement sleeve of synchronizer, sliding

block and the five-speed spring collar.
Remark: the opens of the spring collar shall be in non-
front
alignment
Encase the sliding pad into the gear hub and then cover the
gear sleeve.
Mount the spring retainer under the sliding pad.
Notice, the opening direction of the spring retainer shall
not face-to-face.

Mount of Reverse Gear Assembly

1. Check the reverse idle gear
Measure the radial clearance of the reverse idle gear with dial
gauge.
Standard clearance:
Shang Chi
0.05mm; Tang Chi
(0.04
0.08)mm
Max clearance

Shang Chi
0.05mm; Tang Chi
0.13mm
MT-32 Gear Box
Counter Shaft Assembly and Reverse Idle Gear Assembly (Assembly of Reverse Gear Assembly)

2. Measure the clearance between the reverse idle gear

and gearshift yoke block
Measure the clearance between the reverse idle gear and the
gearshift yoke block with feeler.
Standard clearance:
Shang Chi
0.2mm
Tang Chi
(0.05
0.27)mm
Max clearance

Shang Chi
0.35mm
Tang Chi
0.5mm
Gearbox
Rear Housing Assembly (Element Drawing, Change of Oil Seal, Change of Shaft Bush) MT-33

Rear Housing Assembly

Element drawing

rear housing
cluster

component element rear housing dust

of position-limit cover
mechanism
rear housing oil seal
assembly

oil groove
locating spring bolts and
spring cylindrical pin

oil reservoir

SST Change of Oil Seal

1. The rear housing oil seal shall be changed where necessary.
(a) Dismantle the oil seal with SST.
(b) Press in the new oil seal with SST
SST

2. The driven oil seal of speedometer shall be changed

where necessary
(a) Pry out the oil seal with SST.
(b) Tap the new oil seal into the shaft bracket with SST.
SST
SST

Change of Shaft Bush

The shaft bush shall be changed where necessary
SST
(a) Tear down the oil seal and dust bush.
(b) Heat the ending parts of extension frame to 80
-100
in
the oil groove.
(c) Tear down the shaft bush with SST and mount on the new
shaft bush.
MT-34 Gearbox
Rear Housing Assembly (Inspection On and Change of The Component Elements of Position-Limit Mechanism)

Inspection on and change of the component

elements of position-limit mechanism
1. Tear down the component elements of position-limit
mechanism
(a) Dismantle the bolts with the torque socket spanner.

(b) Punch out the spring cylindrical pin with the drift punch
and hammer.

(c) Tear the component elements of position-limit mechanism

down.

2. Check the component element of position-limit mechanism.

Run and propel the limit stop and the limit stop can return
to the original location automatically, otherwise, change the
limit stop.

3. Mount the component element of position-limit mechanism

(a) Mount the component elements of position-limit mecha-
nism in the rear housing.
(b) Tap the spring cylindrical pins in with drift punch and
hammer as shown in the drawing.
Gearbox
Rear Housing Assembly (Inspection On and Change of The Component Elements of Position-Limit Mechanism) MT-35

(c) Coat the sealing agent on the bolt thread.

(d) Propel the plug with the torque socket spanner.
MT-36 Gearbox
Bearing Front Cover Assembly (Element Drawing, Change of Oil Seal)

Bearing Front Cover Assembly

element drawing

bearing front cover

assembly

front cover oil seal

assembly

washer

Change of oil seal

The oil seal of the bearing front cover shall be changed where
necessary
(a) Pry out the oil seal with screwdriver

(b) Press in the new oil seal with SST.

Depth of oil seal:
Upper tooth
9.5mm
Tang tooth
(12.4
0.4)mm
SST
 Gearbox
Assembly of Gearbox MT-37

Assembly of Gearbox
1. Mount the output shaft in the central link plate
(a) Tap the output shaft in the central link plate while pulling
it, until mounting it in the central link plate.

(b) Mount the stop ring of the rear bearing of output shaft in
with the split-ring-type pliers.
Remarks: The stop ring shall flush with the surface of central
link plate.

2. Mount the input shaft in output shaft

(a) Coat the MP lubricant on the bearing with 13 needle
rollers, and mount the needle rollers in input shaft.

(b) Propel the input shaft in the output shaft and flush the
alignment
groove of synchronizing ring with the sliding block.

3. Mount the countershaft in the central link plate

(a) Mount the stop ring on the rear bearing of countershaft
with split-ring-type pliers.
MT-38 Gearbox
Assembly of Gearbox

(b) Mount the intermediate-gear shaft in the central link

plate, and mount the backup rear bearing with SST while
holding the intermediate-gear shaft.

SST

4. Mount the baffle of rear bearing of output shaft

Mount and propel the bolts with torque socket spanner.
Tightening moment

Tang tooth
(17
22)N
m
Upper tooth
(12
17)N
m

5. Mount the reverse idle gear and shaft

(a) Mount the reverse idle gear and shaft.

(b) Mount the axial pressing plate of the reverse idle gear,
and then propel the bolts tightly.
Tightening moment
(15
20)N
m

6. Mount the bracket cluster of reverse rocker arm

Mount the reverse rocker arm bracket and propel the two bolts
tightly.
 Gearbox
Assembly of Gearbox MT-39

7. Mount the steel ball and the five-speed thrust washer.

locking ball

8. Mount the five-speed gear cluster

(a) Coat the gear oil on the needle bearing.
(b) Mount the five-speed gear cluster.

9. Mount the synchronizing ring and the fifth coupling gear

(a) Mount in the synchronizing ring and the fifth coupling
gear.

(b) Dismantle the old central link plate from the table vice.
(c) Put the gearbox straightly as shown in the drawing.

(d) Flush the groove of synchronizing ring with the sliding

socket spanner block and mount the fifth coupling gear with pressure
machine.
(e) Mount the new central link plate in the table vice.
MT-40 Gearbox
Assembly of Gearbox

10. Mount the split ring

(a) Select the retainer for shaft that leaves the minimum
radial clearance, which is not larger than 0.1mm.

(b) Mount in the retainer for shaft with copper bar and
hammer.

11. Measure the radial clearance of the five-speed gear

cluster.
Measure the radial clearance of the five-speed gear cluster
with the measuring gauge.
Standard clearance

Shang chi
(0.135
0.325)mm
Tang chi
(0.1
0.3)mm

12. Mount the third-fourth-speed gearshift fork axle and the

first-second-speed gearshift toggle fork as well as the
third-fourth-speed gearshift toggle fork
(a) Mount the first-second speed and third-fourth speed
gearshift toggle forks.
(b) Mount the third-fourth-speed gearshift fork axle in the
central link plate and the gearshift toggle fork.

(c) Mount the spring cylindrical pin of third-fourth-speed

gearshift fork.
Notice: The pin port should align with the direction of the
shaft.(Same sa below)
Gearbox
Assembly of Gearbox MT-41

13. Mount the first gearshift fork axle and first gearshift fork
(a) Coat the MP lubricating on the interlocking guidepost
and mount the interlocking guidepost on the first-second-
speed gearshift fork axle.

(b) Mount the interlocking pin in the central link plate with
the magnetic bar.
(c) Mount first-second gearshift fork axle in the first gear-
shift toggle fork and central link plate.

d) Mount the setting bolts of the first toggle fork and tighten
them.
Tightening moment

Upper tooth
(15
20)N
m
Tang tooth
(13
17)N
m

14. Mount the reverse yoke rod, reverse rocker arm and
reverse yoke block
(a) Mount the reverse yoke rod, reverse rocker arm and
reverse yoke block together.
(b) Mount the reverse rocker arm on the reverse rocker arm
bracket.

(c) Coat the MP lubricant on the interlocking guidepost and

mount the guidepost on the reverse gearshift fork axle.
MT-42 Gearbox
Assembly of Gearbox

(d) Mount the interlocking pin in the central link plate with
the magnetic bar.
(e) Mount the reverse gearshift fork axle in the reverse yoke
rod and central link plate.

(f) Mount the spring cylindrical pin with the drift punch and
hammer.

15. Mount the five-speed reverse gearshift guide block and

five-speed reverse gearshift fork axis.
(a) Mount the five-speed reverse gearshift guide block in the
five-speed reverse gearshift guide shaft.
(b) Mount the reverse gearshift fork axle in the next step.

(c) Mount the steel ball in the five-speed gearshift guide

block with the magnetic bar.
(d) Mount the five-speed gearshift fork axle as shown in the
drawing.

(e) Mount the steel ball in the central link plate with mag-
netic bar.
(f) Mount the five-speed gearshift fork axle in the central
link plate.
Gearbox
Assembly of Gearbox MT-43

(g) Tap the pin in the five-speed gearshift toggle fork with
the drift punch and hammer.

(h) Mount the five reverse gearshift guide shaft in the five-
speed reverse guide block and central link plate, and

(i) Tap the spring cylindrical pin in the five-speed reverse

guide block with drift punch and hammer.

16. Mount the retainer ring gripped by the gearshift fork axle.
Mount the clamp retainer ring with the steel bar and hammer
MT-44 Gearbox
Assembly of Gearbox

17. Mount the steel ball, locating spring and locating spring
plug
(a) Mount the steel ball and locating spring.
Remarks:
Mount the short spring at the bottom of the central link plate.

(b) Coat the sealing agent on the plug thread.

(c) Mount the plug and tighten them with the torque socket
spanner.
Tightening moment
(17
22)N
m

18. Tear down the central link plate from the table vice
(a) Tear down central link plate from the table vice.
(b) Dismantle the bolts, nuts and washers

19. Mount the gearbox frame

(a) Coat the sealing material on the coupling face of the
gearbox frame as shown in the drawing.
sealed material

(b) Put down the central link plate straightly as shown in the
drawing.
(c) Mount the gearbox frame on the central link plate as
shown in the drawing.
 Gearbox
Assembly of Gearbox MT-45

20. Mount the stop ring of the front bearing

(a) Mount the two stop rings in the input shaft bearing and
countershaft front bearing with the split-ring-type pliers.

(b) Mount the coated component elements of front cover.

(c) Coat the sealing agent on the bolt thread, and
(d) Mount and propel tightly the bolts.
Tightening moment
(15
20)N
m

21. Mount the rear body, gear-change bar and selection bar
and their housings
(a) Coat the sealing materials on the rear body as shown in
sealed material
the drawing.

(b) Mount the gearshift shaft and gearshift yoke block in the
rear body.
(c) Mount the gearshift catching head in the groove of guide
block, and
(d) Mount the catching head with the rear body together.

(e) Mount and propel tightly the bolts.

Tightening moment

Shang chi
(30
40)N
m
Tang chi
(30
45)N
m
MT-46 Gearbox
Assembly of Gearbox

4WD (f) Fasten the rear cover bolts of the four-gear driving
gearbox
Tightening moment:(30
45)N
m(Tang tooth)

(g) Mount and propel tightly the setting bolts of the gearshift
yoke block.
Tightening moment
(17
22)N
m

22. Mount the steel ball spring and plug

(a) Coat the sealing agent on the plug thread.
(b) Mount the steel ball, setting spring and setting spring
plug.
Tightening moment
(17
22)N
m
23. Check the following items after mounting the rear body
or gearbox
(a) Check the stability of the running input shaft and output
shaft.
(b) Check the gearshift stability of each speed

24. Mount the component elements of the locating mecha-

nism
(a) Mount the black component elements of the locating
mechanism on the side of the five-speed reverse gear.
(b) Mount another component element of locating mecha-
nism and propel it tightly.
Tightening moment
(30
40)N
m

25. Mount the gearshift cover of the gearbox.

(a) Mount the gearshift cover coated with sealing agent.
(b) Mount six bolts and then tighten them.
Tightening moment
(15
20)N
m
Gearbox
Assembly of Gearbox MT-47

26. Mount the clutch frame

(a) Mount the clutch frame.
(b) Coat the sealing agent on the bolt thread.
(c) Mount the nine bolts and then tighten them.
Tightening moment

Upper tooth
(60
70)N
m
Tang tooth
(30
45)N
m

27. Mount the back-up lamp switch.

Tightening moment
(20
40)N
m
28. Mount the driven gear of odometer
(a) Mount the driven gear of odometer.
(b) Mount the bolts and tighten them.
Tightening moment
(10
15)N
m
 TF-1

Transfer Box
page

Notice ........................................................................... TF-2

Troubleshooting ........................................................... TF-3
Product Description and Simple Maintenance ............. TF-5
Dismantle and Mount of Transfer Box .......................... TF-7
Disassembly of Transfer Box ....................................... TF-9
Assembly of Transfer Box ............................................ TF-14
Washing, Inspection, Maintenance and Change .......... TF-24
Washing ................................................................... TF-24
Inspection ................................................................ TF-25
TF
Maintenance and Change of Gear and Chain gear .. TF-28
Attachment for Inspection, Maintenance and
Change of Parts....................................................... TF-30
TF-2 Transfer Box
Notice

Notice
Notice on transfer box disassembly and assembly
Notice shall be taken on the soft handling of the parts (coupling face in particular) during the process of
transfer box disassembly to avoid the collision; each parts shall put down in order so as to avoid of missing
or mistaking.
Notice shall, during assembly process, not only on the aforesaid items, but also on the following items:
1. Wash all parts and fittings before assembly (rubber element and washer excluded).
2. Oil seal, clip for shaft and spring pin of various kinds shall not be reused.
3. Lubricating oil is required to coat on the various friction surface and lubricant on lips of various oil seal.
4. Rolling body is not allowed to use for pressure transmission when mounting various bearings.
5. Lip-type oil seal is not allowed to mount slantwise.
6. The openness on the two sides of spring collar shall not be coupled face-to-face when assembling the
component elements of synchronizer. And
7. No parts is allowed the lubricant leakage and penetration when the transfer box locates at the working
location.
 Transfer Box
Troubleshooting TF-3

Troubleshooting
Common troubles Causes Resolving approaches

Electric gearshift trouble Damage or failure of electrically Refer to the vehicle usage manual to
controlled element, electric module, diagnose the failure element and change
speed sensor, electric motor, electric it as requirement.
clutch, or built-in wire harness. Dismantle the weary or damaged parts
Damage or worn of shifting cam, and change it as requirement.
joint cover, locking sleeve, toggle Dismantle and check the free movement
fork or shift guide axle.Adhesive of sliding element, and change it as
bonding shift requirement

Mechanic gearshift failure under the Break or damage of the shift rocker Change the damaged element.
movement of shifting handle arm or shift lever.
Damage of the guide plate of shifting Open the rear cover of the transfer box to
cam; check the damaged element and change
it.

Difficulty in mechanic gearshift or Incorrect operation. Refer to the vehicle manual for correct
outplace gear engagement operation.
Lubricant of inferior quality or Add the specified oil of given volume.
insufficient volume.
Adhesive bonding of shift toggle fork. Open the rear cover of transfer box to check
and changer the damaged parts.
Adhesive bonding of the sliding joint Open the rear cover of the transfer box to
cover, locking sleeve or gear. check whether the sliding parts can slide
freely along the axle, if not, dismantle it and
change the damaged parts.

Engagement failure of the mechanically Damage or unsuitable adjustment of Adjust or repair the shift lever mechanism.
shift transfer box the shifting mechanism.
Damage or serious wear of the inner Change the seriously wearied parts.
shifting parts, or looseness or
attainment of the shift toggle fork
assembly on the guide shaft.
Unsuitable adjustment of shift lever. Change the loose or weary parts.

Mechanic gearshift seizing at a certain Overlarge loose fit clearance of the Adjust or repair shift lever.Open the
location shift toggle fork on the shift guide transfer box to check the toggle fork and
shaft. guide shaft, and change the parts as
Wear of the shift toggle fork requirement.Open the transfer box to
assembly including pin and contact check whether the parts is wearied or not,
roller. and, if any, change the weary parts.Open
Wear of the shift cam hub and the the transfer box to check whether the
liner. parts is wearied or not, and, if any, change
Attainment of coupling gear the weary parts.Open the transfer box to
check whether the parts is wearied or not,
and, if any, change the weary parts.

No driving of front wheel in the four- Drive chain break Disassemble and check the damage of
gear engagement inner parts, and change the chain.

Noise, which is spreader by the transfer Incorrect lubricant or insufficient Change the lubricant or supplement the
box instead of clutch, engine, drive shaft lubricant volume. lubricant volume.
and other parts, occurs in each speed. Looseness of connecting bolt or other Guarantee the torque of all connecting
connecting element. elements stand at the specified value.
Noise from the transfer box bearing Open the transfer case to check the
bearing and othe parts whether is weared
or daamaged,if this happened,change
the parts.
TF-4 Transfer Box
Troubleshooting

Common troubles Causes Resolving approaches

Noise, which is spread by the transfer Gear noise. Open to check whether there is weary
box instead of the clutch, engine or other Damage or wear of chain gear or element or damaged element (including
parts, occurs at each speed. chain. the odometer gear) and, if any, change
them

Noise occurs in the high-speed or low- Unsuitable tire pressure. Open to check whether there is wear or
speed four-gear driving. damage, and if any, adjust the tire pressure
to suitable value.

Oil leakage in transfer box. Frame Break of transfer box. Change the frame.
Oil leakage of other element. Check the leakage by wiping dry.
Ventilation pipe block Open and clean it and, if necessary,
change it.
Over-added lubricant or lubricant of Use the specified lubricant and adjust the
unsuitable brand lubricant to suitable volume.
Looseness of the bolts on sealing Propel the bolts tightly as requirement.
face.
Sealing glue of different brand or Use the specified sealing glue and propel
unused sealing glue. the bolts tightly as required.
Oil seal wear or damage.
 Transfer Box
Product Description and Simple Maintenance TF-5

Product instruction and simple mainte-

nance
1. Product Introduction
The transfer box adapted by our company is the transfer box
of 45-55 manufactured by Bogeguana, which is two-speed
and time driving, a set of planetary mechanism used is to
borgwarner obtain the speed-reducing performance, while the driving
force is transmitted to the front driving gear by a highly precise
Transfer Assembly NO. of Manufacturer
chain. The planetary gear train and rear output shaft element
of transfer box is lubricated initiatively through oil bath and oil
pump. This transfer box has four gears:

2H-stands for the two high gears
in which, only the two
rear wheel are driven, and the gear ratio of the transfer box
is 1:1

product assembly NO.
4H-stands for the four high gears, in which , all of the four
Manufactuer data wheel are driven, and the gear ratio of the transfer box is
1:1

display
termnumber
N- neutral location (this location only exists in the transfer
displaythe last digit of the year
displaythe specific monthly box of manual gearshift )

No driving force is transmitted
manufactuer data to the wheel when the input shaft and output shaft are
displaythe month numnber
disconnected.
Example display:From January (A) to December (L)
Product instruction and simple maintenance
4L-stands for low gears, the four wheels are all driven, and
the gear ratio of transfer box is 2.48:1.

The gearshift of the mechanical gearshift transfer box is

obtained through the shifting-cam-type guide plate that is
operated by the shift rocker arm.
Sign board: which is fastened at the obvious external location
of transfer box, and on which the detailed data are marked.
TF-6 Transfer Box
Product Description and Simple Maintenance

2. Regular lubricant change

(a) The oil level of lubricant in transfer box shall be checked
when exchanging the engine lubricant or after the vehicle
covers 8000 kilometers, and the lubricant shall be added
as requirement.
(b) The lubricant shall be changed with the specified one
every year or after the vehicle covers 48000 kilometers.
lubricant grade: ATF--3
3. Lubricant inspection approach
(a) Clean the oil filling plug and the around area.
5D 5L
(b) Open the oil-filling plug to check whether the lubricant
can flows out or not.
5D-Oil filling plug (c) if the lubricant can flow out, which means the real
5L-Oil drain plug lubricant volume is under the prescribed value, and the
specified lubricant shall be added into the transfer box
until the lubricant can flow from the oil filler hole.
(d) Propel the oil-filling plug tightly according to the given
Tightening moment.
Tightening moment
(19
30)N
m
Notice: The vehicle shall run for a certain time before
checking or exchanging the lubricant so that the
temperature of lubricant in transfer box may be a little
higher. Do not use hammer or other punching tools to
open or propel the oil drain plug or oil filling plug, otherwise,
the thread hole on the frame will be damaged
4. Lubricant change
(a) Clean the oil filling plug and oil drain plug and the around
area.
(b) Put down a oil container under the transfer box.
(c) Open the oil drain plug.
(d) Open the oil-filling plug.
(e) Drain the lubricant up.
(f) Mount the oil drain plug and screw it up according to the
given Tightening moment.
Tightening moment
(19
30)N
m
(g) Add the lubricant through the oil filler hole until the
lubricant overflows. Mount the oil-filling plug and tighten
it according to the Tightening moment.
Tightening moment : (19
30)N
m
 Transfer Box
Disassembly and Mount of Transfer Box TF-7

Disassembly and Mount of Transfer Box

4
3
2
1

8 6
9

1. input shaft
2. front frame of transfer box
3. rear cover of transfer box
4. flange 5
5. front output fork flange
6. venting valve
7. gasket
8. rear body of gearbox
9. bolt

1. Transfer Box Disassembly Notice: The transfer box shall be guaranteed to

(a) Drive the vehicle on the lifting jack. support by the lifting jack before tearing down
(b) Locate the gear of transfer box at the neutral the sets of bolt and nut that connected with the
position, shift the transfer box to the 2H and transfer box and gearbox. The transfer box is
extinguish the engine. not allowed to hang directly on the gearbox
(c) Disconnect the cell cathode. through spline because such operation will
(d) Lift the vehicle. damage the transfer box parts.
(e) Put down an oil disc under the transfer box, tear (l) Tear down the connecting nuts between the
down the oil drain plug and oil filling plug of the transfer box and gearbox and take down the
transfer to drain all the lubricant up, then re- transfer box.
mount the two plugs. (m) Move the transfer box backward directly until
(f) Disconnect all wires and wire harnesses that the linkage between the input shaft of transfer
connected with the transfer box. box and the gearbox spline.
(g) Take apart the hose on the venting valve of (n) Put down the lifting jack of the transfer box, and
transfer shaft. (o) Tear down the gasket between the transfer box
(h) Disconnect the linkage of the front drive shaft and gearbox. Clean the gasket or glue on the
with the front flange of the transfer box. coupling face of front body of transfer box with
(i) Disconnect the linkage of the rear drive shaft rear body of the gearbox. Take notice not to
with the rear flange of the transfer box. damage the coupling face.
(j) Raise the transfer box up with the jack.
TF-8 Transfer Box
Disassembly and Mount of Transfer Box

2. Transfer box mount (h) Connect the venting valve and the soft ventila-
a) Coat the lubricant grease on the output axial tion pipe.
spline of the gearbox with a thin sleeve contain- (i) Connect the cables of odometer that locates
ing lubricant grease. nearby the transfer box.
b) Mount a new gasket on the mounting face of the (j) Connect all wire harnesses that connected with
transfer box. the transfer box, and
c) Lift the lifting bracket of transfer box and align (k) Add the lubricant of right brand.
it to the same axle with the gearbox. Notice: when starting the engine, if the lubricant
Notice: The transfer shall be guaranteed to flush is added incorrectly or in unsuitable volume,
with the gearbox before connecting the spline. which may lead the transfer box to damage.
Do not handle it forcefully to press the transfer
box spline into the gearbox. Otherwise, damage Notice: as for the transfer box mounted on
will be caused, run the rear output shaft where vehicle, oil pump shall be used when adding oil
necessary to aim at the spline. for it.

(d) Move the transfer box forward slowly so that Notice: In case the transfer box is taken apart for
the spline and pin of the input shaft of gearbox maintenance or inspection, there will be no
reach the front body of the transfer box, and the lubricant supplied by oil pump in the oil passage
gasket attaches on the gearbox completely. on the top of transfer box. Therefore, it is not
(e) Ensure that the mounting holes of the front accurate to control the oil volume by opening the
body of transfer box, gasket, and gearbox are in oil filling plug, in such condition, the oil passage
alignment and then mount the sets of bolt and will be filled with oil once the oil pump runs. If the
nut. wheel can run, such operation can be conducted
Fastening torque
(35-48)N
m on the lifting jack. The oil level shall be rechecked
(f) Connect the rear drive shaft and the rear output once the oil pump runs.
flange of the transfer box.
(g) Connect the front drive shaft and the front (l) Put down the vehicle after finishing the lubri-
output fork flange of the transfer box. cant inspection, and connect the cell cathode.
 Transfer Box
Disassembly of Transfer Box TF-9

2 3 4 5 Disassembly of Transfer Box

1
1. Brief instruction
In case the transfer box is required to be repaired for the
damaged specific element, it shall be taken apart to the degree
on which the damaged element is taken out. And the parts
6 taken apart from the transfer box, if it doesnít include the
damage element, can exist in the form of sub-assembly or
group instead the individual form, otherwise, the parts will be
taken apart individually.
2. Transfer Box Disassembly
Put the transfer box on the worktable and ensure the rear part
or the rear cover faces upward. Put the wooden block under the
1. rear body of transfer box 4. gasket front part of transfer box to keep the transfer box stands
2. flange 5. nut
horizontally. The disassembly process is as follows:
3. oil seal 6. oil plug
(a) Fasten the flange with the torque arm typed T-13-54-
002, screw off the nut to take down the gasket, then take
apart the flange and oil seal.

(b) Take down the two oil plugs from the transfer box body.
1 2
As for the electric gearshift transfer box, tear down the
electric shifting element according to the following
disassembly approach:
(a) Tear down the three bolts, gaskets, sensor and clip for
3
5 wire harness.
4
(b) Tear down the sensor assembly and take apart the O-
4 ring.
6 (c) Tear down the motor assembly.
7

8
1. sensor bracket
2. bolt
3. speed sensor
4. o-ring
5. sensor assembly
6. bolt
7. gasket
8. rear body of transfer box
TF-10 Transfer Box
Disassembly of Transfer Box

9 10 11 1. front case of transfer box

8
2. rear output shaft
3. cluch coil assembly
7 6
5 4. clip
4 5. bearing
3
6. nut
7. transfer cover assembly
2 8. mark plat
1
9. bolt
16 12
13 10. odometer drave gear
17 11. oil seal
14
15 7 12. oil seal
13. bearing
18 14. rear cover of transfer box
15. rolling needle bearing
16. shift guide shaft
17. back spring
18. magnet
19 19. bundle clip
9

3. The disassembly approach for rear cover is as follows (above figure)

(a) Dismantle the nine screws and take down the clip of wire harness and
1 signboard in the same time.
Notice shall be taken to good keeping for the signboard, which includes the
9 information for the substitutes to be changed.
8
(b) Pry the frame lightly so that the sealing glue on the surface disengages, and
7
2 6 then take up the transfer box rear cover assembly directly.
5 (c) As for the electric gearshift transfer box, tear down the oil seal, bearing and
Q
3
three nuts and clutch coil assembly.
(d) Tear down the snapping ring, pull out the bearing from the rear cover and
take apart the odometer meanwhile.
(f) Pull out the oil seal from the rear cover of the transfer box.
(g) Tear down the magnet from the front body of transfer box.
10 (h) Take apart the return spring from the shift guide shaft
11 (i) Clear away the sealing glue on the coupling face of the front housing and
rear cover of transfer box, take notice not to damage the coupling face of
the two housings or cause the materials removed dropping into the transfer
box.
1. output shaft
4. Tear down the shifting element connected with the front axle.
2. shift engagement sleeve assembly
Tear down the following parts from the remaining transfer box housing
3. locking sleeve
assembly (electric gearshift).
4. return spring
5. engagement sleeve
(a) Electric gearshift assembly, tear down the snapping ring and sliding clutch
6. snapping ring sleeve from the shift locking hub.
7. shift lock hub (b) Tear down the shift-locking hub from the rear output shaft.
8. clutch assembly (c) Tear down the shift engagement sleeve assembly and shift toggle fork from
9. fastening snapping ring the rear output shaft and shift guide shaft. Separate the assemblies one
10.shift guide shaft another and tear down the shift guide shaft.
11.toggle fork (d) Disassemble the shift engagement sleeve assembly by taking apart the
snapping ring, engagement sleeve, return spring, and locking sleeve.
(e) A plastic toggle fork that substitutes the metal toggle fork assembly and a
independent contact roller in earlier time.
 Transfer Box
Disassembly of Transfer Box TF-11

5. Tear down the Chain drive system

2 Take apart the following parts from the transfer box housing
4 5 assembly.
3
1 (a) Take apart the snapping ring and washer from the front
output shaft.
(b) Take apart the driving chain sprocket, driven chain
sprocket and drive chain together from the two output
7 shafts.
6
(c) Separate the chain sprocket from the chain.
1. output shaft 5. snapping ring
2. driving chain sprocket 6. transmission chain
3. driven chain sprocket 7. front output shaft
4. washer

6. Oil pump assembly

Take apart the shaft and pump assembly, pipe clip, oil pipe and
4
7 filter from the remaining transfer box housing assembly.

3 6

1. output shaft
1 2. driving chain sprocket
3. driven chain sprocket
4. washer
5. snapping ring
6. transmission chain
7. front output shaft

1 7. Deceleration shifting element disassembly

2
Tear down the following parts from the remaining transfer box
housing assembly.
(a) Take apart the deceleration hub, and deceleration shift
fork assembly from the housing.
(b) Take apart two plastic inserted faces from the decelera-
tion shift fork assembly
1. deceleration gear hub 3
7 4 (c) Disassembly the deceleration shift fork assembly only if
2. inserted face of Shift 5
toggle fork 6 it were broken.Cut the plastic cover,and take out the pin
8
3. plastic sleeve and truckle.
4. contact roller
5. pin
6. pin, contact roller and sleeve assembly
7. deceleration shift toggle fork
8. deceleration shift toggle fork assembly
TF-12 Transfer Box
Disassembly of Transfer Box

8. Take apart the following parts from the remaining trans-

4
fer box housing assembly
(a) Fasten the front fork-type flange with the torque arm of
T-13-54-002 and screw off the nuts to take apart the
gasket, pull out the front fork-type flange assembly and
3 sealing ring.
2
(b) The dust cover may also be pressed down from the front
1
fork-type flange where necessary, and
(c) Take apart the front output shaft.

6 5
7
8
1. fork-type flange 5. front output shaft
2. dust cover 6. oil seal
3. fork-type flange assembly 7. washer
4. transfer box front housing 8. nut

9. Tear down the front body, input shaft assembly and

planetary mechanism assembly
7 10 Tear down the following parts from the remaining transfer box
9
6 8 housing assembly
1
5 (a) Take apart the venting valve.
4 (b) Take apart the six bolts to separate the front body from
3
2 16 the transfer box housing and take down the front body
(take notice not to damage the front-end cover and the
11 transfer housing).
15
14
(c) Take apart the front body assembly, input shaft assembly
13
and planetary mechanism assembly in grouping manner
12 17
18 (loose the snapping ring to take apart the input shaft from
the front end cover).
19 (d) Hold one end of the input shaft on the worktable while
20 open the long end of the snapping ring, press the front
body tightly to disassemble the front body assembly from
the remaining assembly.
1. planetary mechanism 12. oil seal (e) Take apart the snapping ring and oil seal from the front
assembly 13. locating pin body, the pin is only be taken apart where change is
2. gasket 14. transfer box front
necessary.
3. snapping ring body
4. thrust disc 15. snapping ring
(f) Take apart the bearing and gasket from the input shaft
5. sun wheel 16. transfer box front assembly after the bearing gripping loop is taken apart;
6. planetary bracket housing and take apart the input shaft assembly from the planetary
7. input shaft assembly 17. bearing mechanism assembly.
8. input shaft 18. bearing gripping
(g) Take apart the needle bearing and bearing shell from the
9. needle bearing loop
input shaft assembly, and
10. bearing shell 19. bolt
11. transfer box front 20. vent (h) Take apart the snapping ring, thrust disc and sun wheel
body assembly from the planetary assembly, and
(i) Do not try to disassemble the planetary bracket.
 Transfer Box
Disassembly of Transfer Box TF-13

4 10. Take apart the shift convex plate parts (for the electric
3
shift transfer box)
1 (a) Take apart the integrated electric shifting cam from the
2
transfer box housing.
5 (b) Take apart the electric shifting cam from the shift guide
shaft.
(c) Grip the end of shift guide shaft with soft-jaw vices, and
tap the shaft with a screwdriver until the torsion spring
drops off.

1. front body of transfer box housing

2. shift guide shaft
3. torsion spring
4. electric gearshift
5. gasket

11. Disassemble the transfer box housing assembly

Disassemble the transfer box housing assembly in the manner
as follows.
(a) Take apart the oil seal.
(b) Take apart the snapping ring, and pull out the bearing.
(c) The locating pin may only be taken apart from the transfer
box front housing in the case that the pin is loose or
7
6 damaged, and
5 (d) Where the gear ring needs to be changed, it may be
4
3
1
pressed out from the transfer box housing.
2

1. transfer box front housing assembly

2. gear ring
3. oil seal
4. transfer box front housing
5. locating pin
6. ball bearing
7. snapping ring
TF-14 Transfer Box
Transfer Box Assembly

Transfer box assembly

1. Introduction
Please refer to the given instruction of this chapter during
assembly process. And the following items shall be taken
notice on:
(a) In case that the torque of the threaded parts is required,
torque spanner shall be used to screw up the parts.
(b) The small parts shall be coated with the lubricant grease
during the mounting process, so that they are immobilized
at the mounting locations.
(c) SST such as thimble of T-13-54-001 shall be used to press
the oil seal and bearing during the oil seal mount and
bearing mount, do not use the hammer to strike the oil seal
or bearing directly.
2. Lubricating during assembling
All inner parts without lubricant shall be lubricated with the
suitable lubricant before mounting, so that they can be as-
sembled easily and can supply the original lubricant
performance.
(a) If the O-ring and oil seal were not lubricated before
mounting, they may be damaged.
(b) Be sure that the bearing or liner is lubricated completely
before mounting. Because the bearing or liner may be
7
6 leaded into damage even though they are run for a very
5 short time.
4
3 (c) The lips of oil seal and the metal elements that match with
1
2 lips shall be lubricated before mounting.
3. Transfer box housing assembly
1. transfer box front housing assembly
Parts taken apart from the transfer box shall be mounted
2. gear ring
3. oil seal according to the following approaches:
4. transfer box front housing (a) If the gear ring needs to be changed, the tooth-type saddle
5. locating pin rear of new gear ring shall be flushed with the gullet of the
6. ball bearing transfer box front housing when pressing the new gear
7. snapping ring
ring. Press in the gear ring as shown in the left bottom
drawing, in which, the chamfering end is firstly pressed
in. if it is ensured the gear ring is not tilted, then fasten the
2 3 gear ring tightly on the housing.
NMR
1 (b) In case there are two locating pins taken apart, mount two
new locating pins into the housing.
(c) Press the bearing into the transfer box front housing and
mount the snapping ring correctly, and
(d) Put down the new oil seal as shown in the left bottom
4
1. oil seal drawing and press it into the housing.
2. transfer box front housing
3. gear ring
4. locating pin
 Transfer Box
Transfer Box Assembly TF-15

4. Mechanic shift convex plate assembly (for electric shift

transfer box)
The mounting process for the electric shifting element is as
4 follows:
(a) Insert the gasket into the inside of free end of the torsion
3
spring.
2

1. shift guide shaft

2. torsion spring
3. electric shift convex plate
4. gasket

1. torsion spring (b) Slide the torsion spring and gasket along with the shift
2. gasket shaft to the driving tongue and put down the first spring
3. shift shaft ring at the left side of the driving tongue (from the
1 direction of free end of shift shaft).

1. torsion spring (c) Twist the second spring ring of the torsion spring on shift
2. gasket shaft to the right side of the driving tongue.
3. shift shaft

1 2 3
TF-16 Transfer Box
Transfer Box Assembly

1. torsion spring (d) Push the torsion spring and gasket backward together as
2. gasket can as possible
3. shift shaft (e) Mount the electric shifting cam on the shift shaft in such
1
way that the free end of the driving tongue of the cam is
put in first, fasten the cam driving tongue, which shall be
between the two spring ring of two torsion spring, under
2 the driving tongue of shift shaft and put it innermost as
can as possible.
(f) After mounting the toggle fork, then mount the electric
shifting cam assembly in the transfer box housing assembly

5. Assemble for front body, input shaft assembly and plan-

etary component element.
7 10 Mount the following element on the worktable:
9
6 8 (a) Put the planetary bracket assembly on worktable, and the
1
5 end with snapping ring groove shall face upward.
4
3 (b) Mount in the sun wheel and let the part with projecting
2 16 end upward, run the gear of the planetary bracket assem-
bly until it completely engages with the sun wheel.
11 15 (c) Flush the projecting teeth, and then mount the thrust disc
14
13 into the planetary bracket assembly.
12 17 (d) Mount in the snapping ring to complete the whole plan-
18
etary bracket assembly.

19
20

1. planetary mechanism 11. transfer box

assembly frontbody assembly
2. gasket 12. oil seal
3. snapping ring 13. locating pin
4. thrust disc 14. transfer box front body
5. sun wheel 15. snapping ring
6. planetary bracket 16. transfer box housing
7. input shaft assembly 17. bearing
8. input shaft 18. bearing gripping loop
9. needle bearing 19. bolt
10. bearing shell 20. vent
 Transfer Box
Transfer Box Assembly TF-17

(e) In the case that the input shaft is taken apart, what need
1.25-1.75mm to do is to fill the needle bearing as shown in the drawing
and press it in the input shaft, meanwhile, press the new
sliding bearing to complete the whole input shaft assembly.
(f) Raise the planetary mechanism assembly to mount it into
the input shaft assembly; encase the thrust gasket and
press in the bearing through the input shaft end. Encase
the fixed bearing in the snapping ring groove of the input
1. needle bearing 1 2 3 shaft with a snapping ring.
2. bearing roller
3. input shaft

(g) If the transfer box front body is taken apart, press the new
3 located pin in the front body, and the pressing dimensions
are shown in the drawing.
12.70mm
(h) Put down the oil seal as the drawing shows, and press it
in the front body according to the dimensions shown in
2 the drawing.
(i) Put down the front body assembly on two wooden blocks
in the way that the coupling face of the front body and the
1
housing faces upward, so that there is clearance left
between the input shaft assembly and the worktable. Put
4 down the input shaft and planetary mechanism assembly
1. locating pin in the front body, in which the input shaft shall be
2. oil seal
downward. Open the long ends of the snapping ring to
3. front body of transfer box
4. snapping ring
encase input shaft and planetary mechanism assembly
until the snapping ring enters into the external snapping
ring groove of the bearing.
(j) Coat the sealing glue of 1.6mm on the coupling locations
4 of the front end cover and transfer box assembly, The
glue shall be coated continuously without break and steer
clear of the screwed hole.
(k) Screw up the six bolts.
Fastening torque
(27
46)N
m
3
2
1

6. Assembly of front output shaft

Mount the following parts:
(a) If the dust cover is taken apart, mount it by pressing.
6 5 (b) Encase the input shaft, sealing ring, gasket and nuts in the
7 transfer front housing.
8
1. fork-type flange 5. output shaft
(c) Insert the torque arm of T-13-54-002 in the flange hole to
2. dust cover 6. oil seal screw up the nuts.
3. fork-type flange assembly 7. washer Fastening torque
(203
244)N
m
4. transfer box housing 8. nut
TF-18 Transfer Box
Transfer Box Assembly

7. Deceleration shift parts assembly

2 The mounting process is as follows:
(a) If the parts are taken apart for change, assemble the shift
1 toggle fork assembly with a new pin-contact roller
assembly. Press the pin-contact roller in the deceleration
fork hole until the detent passes the hole completely and
seizes the right location. Ensure that the contact roller can
3
run freely.
(b) Mount two inserted faces of toggle fork on the decelera-
6 tion toggle fork assembly.
7
8 9 (c) Engage the deceleration fork assembly and deceleration

5
gear sleeve and put them in the housing, and the decelera-
1. deceleration gear 4 tion gear sleeve shall be put in the planetary mechanism
2. output shaft
assembly that is assembled already. Mount the rear
3. insert face of toggle fork
4. deceleration toggle fork assembly output shaft and joint the bearings at the ends of output
5. pin, contact roller and sleeve assembly shaft and input shaft as well as the spline of the gear
6. deceleration shift toggle fork sleeve.
7. plastic sleeve Remarks: the output shaft assembly can be delayed until the oil
8. contact roller
pump is mounted on the output shaft. The oil pump may be
9. pin
dipped into the lubricant through the oil pump screen, turn the
output shaft in clockwise from the output shaft direction to see
whether there is lubricant pumped out so as to check whether
the oil pump can work normally or not. The parts mounted
readily may be encased in the transfer box housing as an
assembly

8. Oil pump assembly

Q
Ensure the parts of oil pump are completely lubricated when
T
assembling, and the oil can be pumped out from the conical
hole of the oil pump front cover. The mount of oil pump is as
R
follows:
P S (a) Mount the pin on the rear output shaft.

O
(b) Slide the oil pump assembly on the rear output shaft
along with the pin.
(c) Put the gripping hoop at the end of oil pipe that is
N mounted on the oil nozzle of the pump housing, screw up
1. filter
2. oil pump hose the gripping hoop.
3. gripping hoop
4. oil pump assembly
5. output shaft
6. pump pin
7. output shaft and pump assembly
 Transfer Box
Transfer Box Assembly TF-19

9. Assembly of driving chain

2
5 The parts assembly process is as follows:
3 4
1 (a) Put the driving chain sprocket at the rear end of the output
shaft, and the driven chain sprocket is put at the rear end
of the front output shaft on the worktable after the transfer
box housing assembly mount.
1. output shaft 7 (b) Mount the chain on the sprocket.
2. driving chain sprocket 6 (c) Holding the two chain sprockets parallel with the transfer
3. driven chain sprocket
box in the space that the chain on the two sprockets are
4. washer
5. snapping ring
straightened, and encase the chain and sprocket assembly
6. transmission chain through the output shaft, it is required to run the chain
7. front output shaft sprocket slowly to ensure that they engage with the front
output shaft and the spline.
(d) Mount the gasket and snapping ring on the front output
shaft.

10. Shift locking element assembly

1
The parts mounting process is as follows (for the electric shift
transfer box):
9
8 (a) Mount the return spring and locking hub on the locking
sleeve and fasten them with snapping ring to finish the
7
2 6 2W-4W locking sleeve assembly.
5
4 (b) Encase the shift guide shaft in the blind hole of the
3 housing through the deceleration toggle fork assembly
that is already assembled.
(c) Mount the shift toggle fork on the 2W-4W locking sleeve
assembly, which will slide through the shift guide shaft
and rear output shaft.
(d) Joint the combined external gear sleeve spline and the
10
rear output shaft spline as well as the 2W-4W locking
11 sleeve.

1. output shaft 6. snapping ring

2. shift engagement 7. shift lock hub
sleeve assembly 8. clutch assembly
3. locking sleeve 9. fastening snapping ring
4. return spring 10. shift guide shaft
5. engagement sleeve 11. toggle fork
TF-20 Transfer Box
Transfer Box Assembly

(e) As for the electric shift transfer box, encase the as-
2
3 sembled electric shifting cam group and clutch shell in
convex plate 4 the process as follows:
groove (1) Put down the electric shifting cam group as shown in
1 the drawing.
(2) Hold the shift guide shaft downward and raise lightly
the toggle fork assembly. Run the electric shifting
cam group in place, so that the contact roller on
deceleration toggle fork assembly enters in the groove
of shifting cam, and the projecting part of lock
toggle fork is at the rear end of the shifting cam, and
then take reduce the component elements in the
6 5
transfer box housing, meanwhile, joint the shift
1. electric shift convex plate
2. torsion spring shaft on the pin in transfer box housing.
3. shift shaft (3) Locate the clutch shell well through the shift exter-
4. gear down shift fork assembly nal gear sleeve and mount on the snapping ring.
5. shift fork
6. gear shifting shaft

11. Rear cover Assembly

4 5 Mount the parts into the rear cover according to the following
process:
(a) Locate the rear cover on the suitable press machine, the
3
2 coupling face of the rear cover shall face upward and
1
6 parallel with the work face of the press machine.
7 (b) Locate the needle bearing, of which the marked end
facing upward, and press it in the rear cover until the
upper end of needle bearing is 40.47
40.97 lower than
1. clutch washer assembly the coupling face of the rear cover that matches with the
2. snapping ring
front housing.
3. ball bearing 8
(c) Press the ball bearing in the rear cover and mount the
4. transfer box rear body
5. nut snapping ring well.
6. oil seal (d) As for the electric shift transfer box, the parts shall be
7. bearing encased according to the following process:
8. needle bearing (1) Confirm the four O-rings are set on the clutch
washer assembly (one O-ring is located on the coil,
the other three on studs).
Mount on the clutch coil assembly, of which the
wire and stud shall protrude out the rear cover, take
notice not to damage the wire when screwing up the
nuts.
Fastening torque
(8
11)N
m
(2) Encase the motor bearing and oil seal in the rear
cover.
 Transfer Box
Transfer Box Assembly TF-21

1. bolt 12. Assembly of Rear Cover

N V
2. wire harness T U Mount the aforesaid accomplished cover assembly on the
3. magnet transfer box housing according to the following process:
4. return spring S (a) Mount the return spring on the shift guide shaft of the
5. shift guide shaft
transfer box.
6. transfer box rear
(b) Mount the magnet in the groove of the housing.
body assembly
(c) Coat the Letai glue 598 of 1.6mm on the coupling face of
R
housing, steer clear of the screwed hole when coating
Q
continuously.
Notice: try to button the rear cover on the transfer box front
housing with the moderate force during the following process.
P Not too much force is required when mounting the rear cover
7. sign board on the front housing when all aligning conditions are satisfied,
O NM
N 8. driving gear of Odometer in case the rear cover cannot be mounted on the front housing,
9. oil seal take down the rear cover assembly to check the aligning
10. transfer box front housing condition

(d) All of the following aligning conditions shall be satisfied

S when the rear cover assembly is mounted on the transfer
Q R
P box front housing:
O a) Align the pin hole in the rear cover to the pin on the
N housing.
b) Align the rear output shaft to the inner bearing in
cover rear hole.
c) Align the blind hole in the rear cover and the shift
guide shaft; ensure the return spring is not tilted.
Check the hole in velocity sensor of the rear cover
with a pen.
d) Align the shift shaft and the inner bearing in rear
1. locating pin 4. return spring
2. output shaft 5. shift guide shaft
cover.
3. shift shaft 6. output shaft.

(e) Screw up the nine bolts after locating the sign bolts
O
correctly.
N
(f) Encase the gear of odometer in the rear cover assembly
through the spline of the rear output shaft.
(g) Press the new oil seal in the cover assembly

Q
1. wire harness clip
2. motor assembly
3. bolt
4. sign board
TF-22 Transfer Box
Transfer Box Assembly

12. Mount the external electric shifting element (for the elec-
1
tric shift transfer box)
(a) Locate the motor assembly by aligning the triangle
groove on motor to the shift shaft.

1. motor assembly
2. shift shaft

2
(b) Move the motor to combine the shift shaft and keep it
1
close to the rear cover. Then run the motor clockwise
until the motor locates the correct place and the mooting
holes are aligned.
(c) Mount the O-ring on the velocity sensor and encase the
4
3 velocity sensor assembly in rear cover. A clip and three
5
bolts shall be mounted on the velocity sensor.
6
Fastening torque
(8
11)N
m
7
(d) Mount the bolts and gaskets on the end of motor clip.
8
Fastening torque
(8
11)N
m
9
1. fixed sensor bracket 6. motor assembly
2. bolt 7. bolt
3. sensor assembly 8. gasket
4. velocity sensor 9. transfer box rear body
5. o-ring
 Transfer Box
Transfer Box Assembly TF-23

2 3 4 5 13. Flange assembly

1 The parts mount process is as follows:
(a) Encase the two oil plugs in the rear cover.
(b) Encase the flange, sealing ring and gasket, and then
screw up the nuts.
6 Fastening torque
(203
244)N
m

1. transfer box rear body

2. flange
3. oil seal
4. gasket
5. nut
6. oil plug
TF-24 Transfer Box
Washing, Checking, Up-Keeping and Exchanging (Washing)

Washing, Inspection, Maintenance or Change

1. Washing
Notice: check the metal rag around the magnet first before washing, large granule or irregular metal
granule shows the disintegratation or similar damage. Small or fine metal granule shows the uneven
or serious wear. If the metal rag is founded, notice shall be taken on damage and wear inspection
during checking the rotating parts and the element matched with the rotating parts.
(a) Common washing
Wash the parts in cleaning agent to clean away the old lubricant and deposit. Clean away the deposit in oil hole
with brush. Take notice not to scrape the metal coupling face when washing the parts cannot be cleaned with
brush.
(b) Dry the washed parts by blowing
Dry the washed parts by blowing the low-pressure compressed air (max pressure is 137.9kPa), because cloth
thread may be left during cleaning the parts with cloth. The bearing shall be held by hand to prevent it from
rotating when blowing it.
(c) Bearing lubrication
The ball bearing and needle bearing shall be lubricated with the lubricant for transfer box after washing. As
the non-lubricated bearing may cause damage when be dry. Cover the lubricated bearing to prevent dust
entering in.
Transfer Box
Washing, Checking, Up-Keeping and Exchanging (Checking) TF-25

Checking
1. Common Checking process
Check all parts by visual check to see whether there is damage
or serious or uneven wear (parts needed be substituted by new
parts such as O-ring, oil seal and etc. shall be excluded).
Abandon the damaged or weary parts that will affect on their
performance. The check items are as follows:

Burr: tips protruded from the material regionally

Rag: broken small blocks or particles

Crack: surface thread showing the material is partly or
completely separated.

Excessive abrasion
Refer to the serious or obvious abra-
sion beyond of application limit.

Reduction change
Material slip caused by the heavy
pressure on part of it.

adhesive bonding
Granules of the soft metal are dis-
persed and bonded on the hard metal surface.

Ditch trance: partial crack or trough that means the material
transfer instead of material loss.

Pitting corrosion
Damages to the metal surface caused by
pressure, which are displayed due to color change caused
by heat generated by metal friction.

Step wear
a weary step may be seen or felled between the
neighboring interface or between the non-touching face
due to the excessive wear.

Uneven wear: Partially, unevenly distributed wear, which
includes holes, bright spots, uneven polishing or other
visual drawbacks.
2. Gear or Chain sprocket tooth inspection
Check the gear and chain sprocket tooth according to the
following process:
(a) Normal gear shaving trace.

normal gear shaving trace

(b) Normal gear grinding trace.

normal gear grinding trace

TF-26 Transfer Box
Washing, Checking, Up-Keeping and Exchanging (Checking)

(c) Ideal engagement contact area

(d) Acceptable side-deflective contact area

(e) Unacceptable side deflective contact area that must be

changed.

(f) Acceptable side-deflective contact area

(g) Unacceptable side deflective contact area that must be

changed.
Transfer Box
Washing, Checking, Up-Keeping and Exchanging (Checking) TF-27

(h) Acceptable contact area deflecting to the tooth top.

(i) Unacceptable contact area deflecting to the tooth top,

which must be changed.

(j) Acceptable contact area deflecting to tooth root.

(k) Unacceptable contact area deflecting to tooth root, which

must be changed.

4. Key tooth inspection

Check the broken or peeled spline teeth. The spline teeth may,
if only small part is peeled off, be repaired in the same way as
that for the gear teeth, and can be reused. In case the spline
tooth is broken, the spline must be abandoned. The contact
type of spline is not the same as that for gear; however, spline
that shows step sliding must be abandoned.
TF-28 Transfer Box
Washing, Checking, Up-Keeping and Exchanging (Maintenance or Change of Gear or Chain Sprocket Gear)

Maintenance or Change of Gear or Chain

Sprocket Gear
1. Maintenance principle
(a) Conduct the maintenance for the partial, small peel off
with the suitable manual high-speed grinding tool.
(b) Do not clear away the metal as can as possible when
grinding the matrix metal.
(c) All pointed angles and sides must be repaired as the slip-
pery contour line. Because the pointed angle or edges
may be peeled off again or developed into crack.
(d) Clear away the burr with the suitable grinding stone. Take
notice not to damage the matrix when clearing away the
projecting materials, and
(e) When substituting the non-repaired parts (such as
bearing), if the part is doubted in its re-application
capability, it must be changed.

2. Cases for gear or chain sprocket maintenance or substi-

tuting
(a) The gear, being peeled off at the two sides of tooth top in
contact face, may be repaired for reuse.

(b) The gear, being peeled off at the central tooth top of
contact face, may be repaired for reuse.

(c) The gear, being peeled off at one side of the non-contact
face, may be repaired for reuse.
Transfer Box
Washing, Checking, Up-Keeping and Exchanging (Maintenance or Change of Gear or Chain Sprocket Gear) TF-29

(d) The gear, being peeled off at the center of one side of
contact face, may be repaired for reuse

(e) The gear, being peeled off in the center of contact area,
shall be changed.

(f) The gear, being peeled off at two sides of tooth top, shall
be changed.
TF-30 Transfer Box
Washing, Checking, Up-Keeping and Exchanging (Attachment for Inspection Maintenance or Change of Parts)

Attachment for Inspection Maintenance or Change of Parts

Parts (items) Checking items Acceptance/Refusal
All parts (including Crack inspection, distortion inspection and ero- All parts with crack, all parts that are bended,
all springs) sion inspection distorted or poor in round bouncing are refused.
All threaded parts Thread inspection for buckle missing or other Those parts cannot be threaded or bottomed in
damage overlap manner shall be refused.
Flange and fork Please refer to the paragraph of
inspection
to Please refer to the
inspection paragraph
for
flange check the spline. spline inspection.
Velocity sensor, mo- Please refer to the part of electric appliance Change the parts and fittings as requirement
tor assembly
Parts of electric clutch
system
Sliding bearing Inside surface inspection for the sliding bearing In the case that the bearing has pitting corrosion
or other damage, refuse it.
Ball bearing Check visually the ball and track of the ball Refuse to use the damaged bearing;
bearing to see whether there is damage such as Refuse to use the damaged or loose bearing; or
adhesive bonding, pitting corrosion, etc. Check the axial clearance to see whether it
Ensure that the bearing are all lubricated, run the exceeds 0.23mm.
outer race of the bearing while holding the inner
one to feel whether there is poor running or
corrosion, the bearing shall be run smoothly
without excessive clearance.
Needle bearing Check the bearing needle roller and track to see Refuse to use the damaged bearing.
whether there is damage such as adhesive
bonding, pitting corrosion, etc.
The rear cover, front Check to see whether there is burr on the cou- Clear away the burr according to the paragraph
body and front hous- pling face or other damage that impedes assem- of
inspection
, otherwise, change the dam-
ing of transfer box bling or sealing. aged element

Rear cover of trans- Check the bearing hole Refuse to use the assembly that has pitting
fer box corrosion
Odometer gear Check the gear teeth referring to the Inspection Refer to the gear or chain sprocket inspection in
Paragraph
inspection paragraph
.
Clutch shell, joint Check the spline according to the Inspection Refer to the spline inspection of
inspection
outer gear sleeve and paragraph paragraph

joint cover
Locking sleeve Check the wear or damage of the toggle fork Refuse the parts with step slipping or damage.
groove
Shift guide shaft Check the deformation situation Refuse to use the bend shaft; clear away the burr
Check the burr or other damage on outer race according to the
inspection
paragraph, oth-
Check the wear of outer race erwise refuse to use.
Refuse to use the shaft with step slipping or
other damage.
Shift toggle fork Check whether there is wear or damage at the If any step slipping or damage is found, refuse
location where the toggle fork combines with to use it.
the shifting cam and gear sleeve.
Transfer Box
Washing, Checking, Up-Keeping and Exchanging (Attachment for Inspection Maintenance or Change of Parts) TF-31

Attachment for Inspection Maintenance or Change of Parts

Parts (items) Checking items Acceptance/Refusal
Shift toggle fork as- Check the wear and damage of the inserted face If any step wear or damage is found, the inserted
sembly that is combined with gear sleeve; face shall be refused to use.
Check to see whether the contact roller can If the contact runs difficultly or is damaged, a
rotate freely or is damaged or not new pin-contact roller and new cage assembly
shall be used.
Driving and driven Check the sprocket teeth according to Refer to the sprocket teeth inspection of
chain sprocket the
inspection
paragraph
inspection
paragraph
Shift toggle fork as- Check the inner diameter that matches with the If any pitting corrosion or damage is found,
sembly output shaft refuse to use it.
Driving chain Check the step sliding, looseness or damage of Refuse to use the weary or damaged driving
pin or connecting element chain

Filtering screen Check to see the filtering screen is clean or with Clean it where necessary, and abandon the dam-
small hole or damage aged one.
TF-32 Transfer Box
Washing, Checking, Up-Keeping and Exchanging (Attachment for Inspection

Maintenance or Change of Parts

Pump shell Check to see whether there is pitting corrosion Abandon it in case it is seriously damaged or
or step slipping worn
Output shaft Check the spline, check the surface that matches Refer to the spline inspection of
inspection

with bearing and check the distortion according paragraph;
to
inspection
paragraph Refuse to use the one with pitting corrosion or
damage;
Refuse to use the one that is bending or poor in
round bouncing.
Deceleration hub Check the spline of chain sprocket and check the Refer to the spline inspection of
inspection

wear or damage of the location where matches paragraph; refuse to use the one with step slid-
with the toggle fork according to the ing or damage.

inspection
paragraph

Front output shaft Check the surface where matches with the Refuse to use the one with pitting corrosion or
bearing; damage
Check the spline according to the
inspection
:
paragraph

Input shaft Check the spline according to the
inspection
Refer to the spline inspection of
inspection

paragraph paragraph;
Check the distortion Refuse the one that is bending or poor in round
bouncing.
Thrust washer and Refuse to use the one with pitting corrosion or
Check the pitting corrosion
thrust disc damage
Sun wheel Check the gear teeth and spline according to the Refer to the gear teeth inspection and spline

inspection
paragraph inspection of
inspection
paragraph.
Planetary mechanism Check the gear teeth according to the Refer to the gear teeth inspection of
assembly
inspection
paragraph;
inspection
paragraph;
Check the wear and looseness of the planetary If any step sliding or pitting corrosion is found,
gear pin; check the wear of thrust gasket refuse to use it
Electric shifting cam Check to see whether there is step slipping or If any step sliding or pitting corrosion is found,
pitting corrosion refuse to use it
Shift guide shaft Check to see whether there is step slipping or If any step sliding or pitting corrosion is found,
pitting corrosion refuse to use it
Check the distortion situation Refuse to use the bending one
Planetary gear ring Check the transfer box housing assembly to see
Check the match performance of it with the
transfer box housing whether the gear ring is loose or not in the
housing
Check the gear teeth according to the Refer to the gear teeth inspection of

inspection
paragraph
inspection
paragraph
Transfer box housing Check the holes matches with the bearing Abandon the one with pitting corrosion or
damage.
 PR-1

Drive shaft
page

Notice .......................................................................... PR-2

Troubleshooting .......................................................... PR-2
Drive shaft ................................................................... PR-3

PR
PR-2 Drive Shaft
Notice and Troubleshooting

Notice
Notice: do not grip the drive shaft sleeve too tight with vice
so as to avoid the deformation.

troubleshooting
Trouble Causes Resolving approaches
Noise Wear of universal joint yoke spline; Change the drive shaft;
Wear of central bearing; Change the central bearing;
Wear or seize-up of cross shaft bearing Change the bearing of cross shaft

Vibration Oscillation difference of the drive shaft; Change drive shaft

Drive shaft imbalance; Change drive shaft
Wear of the liner of rear bearing in the lengthening shell of Change the liner
gear box;
Spline seize-up of the universal joint yoke Change drive shaft
 Drive Shaft
Drive Shaft PR-3

Drive Shaft
Element Drawing
2WD
two-joint type
universal joint flange fork



bearing of cross shaft

snapping ring

rear axle drive shaft 74
5

cross shaft
universal joint foke

three-joint type

center support flange

bearing

bearing of cross shaft front joint of rear
axle drive shaft

snapping ring

washer
washer

universal
cross shaft

joint foke 40
5

universal joint
flange fork

universal joint
flange fork

rear section of
rear axle drive 74
5
shaft
74
5

N*m : specified torque

Parts that cannot be reused after being used
PR-4 Drive Shaft
Drive Shaft

Element Drawing(continued)
4WD
front axle drive shaft

74
5

74
5 front axle drive shaft

rear axle drive shaft

two-joint type
universal joint flange fork

bearing of cross shaft

snapping ring

rear axle drive shaft 74
5

universal joint yoke

cross shaft

74
5 center support
bearing flange
three-joint type
bearing of cross shaft

snapping ring

universal joint
flange fork washer
universal joint flange fork


front joint of rear


axle drive shaft 40
5
74
5

rear section of 74
5
rear axle drive
shaft

74
5

N*m : specified torque

Parts that cannot be reused after being used

 Drive Shaft
Drive Shaft PR-5

assembly mark Disassembly of Drive Shaft

(2WD)
1. Take apart the universal joint flange fork of the drive shaft
from the differential flange.
(a) Label the two flanges with assembly remarks.
(b) Take apart the four sets of bolt and nut.

2. Take apart the center support bearing from the frame

beam (for the three-joint type)

3. Take apart the drive shaft from the gearbox

(a) Pull out the universal joint yoke from the gearbox.
(b) Insert the SST in gearbox for oil leakage prevention.

SST

assembly mark
(4WD)
Rear axle drive shaft
1. Take apart the universal joint flange fork of rear axle drive
shaft from the differential flange.
(a) Label the two flanges with assembly marks.
(b) Take apart the four sets of bolt and nut.

2. Take apart the center support bearing from the frame

beam (three-joint type
PR-6 Drive Shaft
Drive Shaft

3. Take apart the drive shaft from the gearbox.

(a) Pull out the universal joint yoke from the gearbox.
(b) Insert the SST in gearbox to prevent the oil leakage
Front axle drive shaft

SST

4. Tear down the front universal joint flange fork of the front
drive shaft.
(a) Hang he front end of the front axle drive shaft.
(b) Label the assembly mark on the flange
(c) Take apart the four sets of bolt and nut.

5. Disconnect the rear universal joint flange fork from the

assembly mark
front axel drive shaft along the transmission path.
(a) Label the assembly marks on each flange.
(b) Take apart the four sets of bolt and nut.

Drive shaft disassembly

assembly mark 1. Separation of the rear joint of the rear axle drive shaft
from the front joint of rear axle drive shaft
(a) Label the assembly marks on each flange.
(b) Take apart the four sets of bolt and nut.

2. Take apart the center support bearing from the front joint
of the rear axle drive shaft.
(a) Loosen the riveted nut by chiseling with a chisel and
hammer.
 Drive Shaft
Drive Shaft PR-7

(b) Lock the flange with SST tools to tear down the nuts.
(c) Label the assembly marks on flange and shaft.

assembly mark

SST

(d) Tear down the flange from the front joint of rear axle
drive shaft with SST tools.
SST

3. Take apart the universal joint yoke from the rear joint of
assembly mark
rear axle drive shaft.
(a) Label the universal joint yoke and the shaft with assem-
bly marks.
(b) Pull out the universal joint yoke from the shaft.

Inspection on Drive Shaft Parts

1. Cross shaft bearing inspection
Check the wear or damage situation of the cross shaft bearing
and change the weary or damaged bearing where necessary.

2. Check the wear and damage situation of the central

bearing.
Check the bearing to see whether it can run freely.
In case that the bearing is damaged or wearied or cannot run
freely, change it in time.
PR-8 Drive Shaft
Drive Shaft

3. Inspection for the front axle drive shaft

(a) Check the wear or damage situation of the shaft.
(b) Check the wear or damage situation of the two universal
joints

grease nozzle 4. Inspection for the drive shaft lubrication

If the drive shaft is not lubricated completely, add the Lithium
base lubricant grease with SST.

rear axle drive shaft front axle drive shaft

Cross bearing change

assembly mark
assembly mark 1. Label the shaft and universal joint yoke with assembly
marks.

2. Take apart the snapping ring.

(a) Tap in the outer bearing race lightly.
(b) Take apart the four snapping rings in the grooves with
two screwdrivers.

3. Take apart the cross shaft bearing

(a) Pull out the bearing from the drive shaft with SST tools.
Remarks: Pull up the part A in the drawing to a enough height
SST so that it cannot contact the bearing.
A
 Drive Shaft
Drive Shaft PR-9

(b) Grip the outer bearing race with a vice to tap out the drive
shaft lightly with a hammer.
Remarks: Take apart another bearing with the same approach.

(c) Mount the two outer bearing races that are taken apart on
the cross shaft.
(d) Pull out the bearing on the universal joint yoke with SST
SST
tool, and

(e) Grip the outer bearing race in the vice and tap lightly out
the universal joint yoke with a hammer.
Remarks: the bearing at the other end may be taken apart with
the same approach.

4. Cross shaft bearing mount

(a) Coat the lithium base grease on the cross shaft and the
bearing.
Remarks: do not over coat the lubricant.

(b) Align the assembly marks on the universal yoke and on

the shaft.
PR-10 Drive Shaft
Drive Shaft

SST (c) Encase the new cross shaft in the universal joint yoke.
(d) Mount the new bearing on the cross shaft with SST tool,
and

(e) Adjust the two bearings with SST tool so that the widths
of two snapping ring grooves are equal and maximum.

5. Snapping ring mount

(a) Mount two snapping rings with the same thickness.
Remarks: Do not use the used snapping ring.

(b) Tap the universal joint yoke lightly with a hammer until
there is no clearance between the outer bearing race and
the snapping ring.

6. Cross shaft bearing inspection

Check the cross shaft bearing to see whether it can run freely
Remarks: the approach for mounting the cross shaft bearing at
the bearing end is the same.
 Drive Shaft
Drive Shaft PR-11

2WD 4WD Drive shaft assembly

1. Mount the center support bearing on the front joint of rear
forward
axle drive shaft.
Remarks: The notch of the center support bearing shall face
backward when mounting it.

2. Mount the flange joint on the front joint of rear axle drive
assembly mark shaft.
(a) Coat the spline of front joint of rear axle drive shaft with
lithium base grease.
(b) Mount flange joint on the shaft and align the assembly marks.
Remarks: if the central flange joint or the front joint of the rear
axle drive shaft is required to change, the front and back
universal joint yokes of the rear axle drive shaft shall face in the
same direction when re-assembling.

SST (c) Lock the flange joint with SST and screw up the newly-
changed nut to press the bearing in place.
(d) Loosen the nuts.
(e) Tighten the nuts again, and
(f) Rivet the nuts with hammer and punch.

3. Drive shaft mount

(a) Align the assembly marks on flanges, and connect the
assembly mark
two flanges with four sets of bolt and nut.
Remarks: if the central flange or the front joint of the rear axle
drive shaft is required to be changed, the front and back
universal joint yokes of the front joint of rear axle drive shaft
shall face in the same direction when reassembling them.
(b) Screw up the sets of bolt and nut according to the
specified torque.
Fastening torque: (74
5)N
m
4. Insert the universal joint yoke in the universal joint yoke
(4WD).
assembly mark
(a) Coat the lithium base grease on the sliding surfaces of the
drive shaft spline and the universal joint yoke.
(b) Align the assembly marks on universal joint yoke and
drive shaft.
(c) Insert the universal joint yoke in drive shaft.
PR-12 Drive Shaft
Drive Shaft

Mount of Drive Shaft

(2WD)
1. Insert the universal joint yoke in the gearbox.
(a) Tear down the SST tools.
(b) Push the universal joint yoke into the gearbox.

SST

assembly mark 2. Connect the universal joint flange of the rear joint of rear
axle drive shaft and the relative the differential flange.
(a) Align the assembly marks on the two flanges and connect
the flanges with four sets of bolt and nut.
(b) Screw up the sets of bolt and nut according to the
specified torque.
Fastening torque
(74
5)N
m

3. Mount the center support bearing on the frame beam

(three-joint type)
(a) Use two bolts to mount the center support bearing on the
frame beam and tighten them manually.
forward (b) Check the bearing seat, which shall be vertical with the
drive shaft, and change it where necessary.
(c) Check the central line of the central bearing and ensure
that the central lines of the central bearing and the bear-
ing seat shall be the same when the vehicle is in the non-
loaded stage. And adjust the bearing seat only it is
necessary.
(d) Screw up the mounting bolts according to the specified
torque.
Fastening torque
(40
5)N
m

assembly mark
(4WD)
1. Connect the universal joint flange fork of the front axle
drive shaft with the flange that matches with the transfer
box.
Align the assembly marks and use four sets of bolt and nut to
connect the flange fork with the flange, screw up the sets of bolt
and nut according to the specified torque.
Fastening torque
(74
5)N
m
 Drive Shaft
Drive Shaft PR-13

2. Mount on the front axle drive shaft.

Mount on it and screw up the four bolts according to the
specified torque.
Fastening torque
(74
5)N
m

assembly mark
3. Connect the universal joint flange fork of the rear axle
drive shaft on the relative differential flange.
(a) Align the assembly marks on flanges and connect the
flanges with four sets of bolt and nut, and
(b) Tighten the sets of bolt and nut according to the specified
torque.
Fastening torque
(74
5)N
m

4. Mount the center support bearing on the frame beam

(three joint type)
(a) Use two mounting bolts to mount the center support
bearing on the frame beam and screw up them manually.

(b) Check the bearing seat, which shall be vertical with the
drive shaft, and adjust the bearing seat when necessary.
(c) Check the central line of the central bearing. The central
line of the central bearing shall be the same with that of
forward
the bearing seat when vehicle is in the non-loaded stage.
(d) Adjust the bearing seat if necessary, and

(e) Screw up the mounting bolts according to the specified

torque.
Fastening torque
(40
5)N
m
 SA-1

Suspension System and Automobile Axle

Page

Troubleshooting .......................................................... SA-2

Alignment of Front Wheel ............................................ SA-3
(Dr/2WD)
Front Wheel Hub and Steering Knuckle ...................... SA-10
Front Wheel Hub ..................................................... SA-11
Steering Knuckle ..................................................... SA-14
Front Suspension ........................................................ SA-16
Ball Stud .................................................................. SA-17
Torsion bar .............................................................. SA-19
Lower Arm and Vibration Damper ........................... SA-21
Upper Arm ............................................................... SA-24
Guide Level ............................................................. SA-26
Lateral Stabilizer ..................................................... SA-27
(SF/2WD) SA
Front Wheel Hub and Steering Knuckle ...................... SA-28
Front Wheel Hub ..................................................... SA-29
Steering Knuckle ..................................................... SA-32
Front Suspension ......................................................... SA-36
Ball Stud ................................................................... SA-37
Torsion bar ............................................................... SA-38
Lower Arm and Vibration Damper ............................ SA-39
Upper Arm ................................................................ SA-42
Guide Level .............................................................. SA-43
Lateral Stabilizer....................................................... SA-43
(SF/4WD)
Front Wheel Hub and Steering Knuckle ....................... SA-44
Front Wheel Hub ...................................................... SA-45
Steering Knuckle ..................................................... SA-49
Constant Speed Drive Shaft ........................................ SA-54
Front Speed Reducer .................................................. SA-57
Change of Oil Seal of Driving Bevel Gear Of
Front Speed Reducer ............................................. SA-57
Dismantle of Front Speed Reducer ......................... SA-61
Change of Axle Shaft Oil Seal ................................. SA-63
Disassembly and Assembly of Front Speed Reducer .... SA-65
Assembly of Front Speed Reducer ......................... SA-74
(Back)
Rear Axle Shaft ........................................................... SA-79
Rear Speed Reducer .................................................. SA-83
On-vehicle Change of Oil Seal of Main Teeth ......... SA-84
Dismantle of Rear Speed Reducer .......................... SA-85
Disassembly of Rear Speed Reducer ..................... SA-85
Assembly of Rear Speed Reducer .......................... SA-89
Mount of Rear Speed Reducer and
Differential Assembly .............................................. SA-94
Rear Differential .......................................................... SA-95
Rear Suspension ......................................................... SA-97
SA-2 Suspension System and Automobile Axle
Troubleshooting

Troubleshooting

Trouble Causes Inspection items

Body wandering/body Tire wear or improper air inflation Inflate the tire to the proper pressure or change
dragging the tire.
Incorrect alignment of front wheel Check the situation of alignment of front wheel
Over-tightened wheel bearing Adjust the wheel bearing
Part looseness or damage of front/rear sus- Tighten or change the suspension element
pension
Wear or looseness of steering rod system Tighten or change the steering rod system
Poor connection or damage of steering de- Adjust or repair the steering device
vice
Body sink Overloaded vehicle Check the loading mass
Wear of vibration damper Change vibration damper
Poor spring performance Change spring

Left-right vibration/up- Improper air inflation Inflate the tire to suitable pressure
down bouncing Bending or damaged lateral stabilizer Change stabilizer
Vibration damper wear Change vibration damper

Front wheel vibration Tire wear or improper air inflation Change the tire or inflate to the proper pressure
Imbalance of wheels Balance the wheels
Vibration damper wear) Change vibration damper
Improper Alignment of Front Wheel Check Alignment of Front Wheel
Wheel bearing wear or improper adjustment Change or adjust the wheel bearing
Ball joint or liner wear Check ball joint) or liner
Steering linkage looseness or wear Tighten or change steering linkage
Poor adjustment or damage of steering mecha- Adjust or repair the steering device
nism
Abnormal tire wear Improper air inflation Inflate the tire to the proper pressure
Vibration damper wear Change vibration damper
Poor Alignment of Front Wheel Check the Alignment of Front Wheel
Suspension system wear Change suspension element
Speed reducer leakage Over-high oil level or improper oil quality Discharge the oil for change
Oil seal wear or damage Change oil seal
Flange looseness or damage Tighten or change the flange

Noise inside the Over-low oil level or inferior oil quality Discharge the oil and change with new one
axleNoise inside the axle Over-large wandering clearance between Check the wandering clearance
driving bevel gear and driven bevel gear
Wear and disintegration of driving bevel Check the gears
gear and driven bevel gear
Bearing wear of driving bevel gear Change the bearing
Bearing wear of rear axle shaft Change the bearing
Bearing looseness or wear of speed reducer Tighten or change the bearing
Suspension System and Automobile Axle
Alignment of Front Wheel (Dr SL SK SY SJ) SA-3

Alignment of Front Wheel

(Dr SL SK SY SJ)
1. Inspection should be conducted for the following items to
remove the trouble
(a) Check the tire abrasion and air inflation situation
Tire inflation pressure:
Front (220
0)kPa
Back (240
0)kPa
(b) Check the front wheel bearing to see whether it is loose.
(c) Check the front suspension to see whether it is loose.
(d) Check the steering driving device to see whether it is
loose, and
(e) Check the front vibration damper work to see whether it
is loose.

2. Measure the ground clearance of the chassis.

Chassis ground clearance:
Dr
2950+5mm
SL SK
(255
2)mm
SY
(310
2)mm
SJ
(295
1)mm
If the chassis ground clearance of the vehicle is sub-standard,
push down the body or raise it for a trial adjustment, if fails,
check the spring or suspension element to see whether they are
normal.
Remarks: adjust the chassis ground clearance to a specified
value before checking the Alignment of Front Wheel
parameters.

3. Mount on the four-wheel locating device.

The mount should be conducted according to the manufacturerís
instructions.
SA-4 Suspension System and Automobile Axle
Alignment of Front Wheel (Dr SL SK SY SJ)

A B B A 4. Adjust the wheel angle

Take apart the limit bolts of the steering knuckle to check the
steering angle A of inner wheel.
Inner wheel steering angle
Dr SL SK SY
( 36
40
)
front SJ
( 32
34
)
Remark: The wheel should not contact the body or brake hose
when the steering wheel reaches the limit position.

In case the steering angle of inner wheel doesnít conform to the

standard value, adjust the wheel angle through adjusting the
limit bolts of the steering knuckle.
Fastening torque
(90
0)N
m(SJ)
adjusting bolt If the wheel angle fails to be adjusted within the standard value,
change the weary or damaged parts of steering system.

5. Adjustment for inner tilt angle of kingpin, outer tilt angle

inner tilt angle of kingpin outer tilt of front wheel and back tilt angle of kingpin
angle of Item Applicable vehicle type Location parameter
front wheel Inner tilt Dr SL SK SY 9
30
 45

angle of
kingpin SJ 14
52

Mechanic
Outer tilt Dr SL SK SY 0
30
 20

steering
angle of
front Dr 0
10
 10

wheel Power
SL SK SY 0
20
 10

steering
SJ 0
30
 15

Mechanic
Back tilt Dr SL SK SY 1
50
HPM

-20

back tilt angle of steering
angle of
kingpin Power steer- Dr SL SK SY 2
45
 15

kingpin
ing SJ 3
 15

If the tilt angle fails to fall within the specified values, make an
adjustment through adding or reducing the gaskets on the
location of upper arm.
Gasket thickness: 3.0, 2.0 and 1.0mm
Once the gasket thickness increases by 1mm, the outer tilt
angle of wheel will change by 7', while the back tilt angle of
kingpin will change 20'.
After the wheel outer tilt angle and the back tilt angle of kingpin
are adjusted, if the inner tilt angle of kingpin still fails to the
specified value, check the steering knuckle or front wheel to
see whether they are bending or loose.
 Suspension System and Automobile Axle
Alignment of Front Wheel (Dr SL SK SY SJ) SA-5

6. Wheel toe-in adjustment

(a) Verify that each wheel has been located forward in a line.
push forward the vehicle; (b) Mark the tire center at the bearing height on the tread of
left and right tire, and measure the distance between the
marks on left and right treads.
(c) Push forward the vehicle until the mark on the back tread
of tire moves to the front.
Remark: the toe-in measurement should be conducted from the
same spot at the same height.
(d) Measure the distance between the two marks on the front
of two treads.
Toe-in value: (0-2)mm

(e) Loosen the clamping bolts of connecting pipe.

(f) Adjust the toe-in angle through the approach according to
forward
which rotate the left and right drag rod tube by a same
angle.
Remark: check the lengths of the two drag rods to see whether
the two rods are same in length.
A B
Length error of the left and right drag rod should not
A=B be larger than 2.0mm.
(g) Tighten the clamping bolts.
Fastening torque
(20
) N
m
(h) Locate the split pin well.

7. Check the sliding measuring situation.

Check the sliding situation with the sliding measuring tester.
Sliding measuring value:
.5m/km
SA-6 Suspension System and Automobile Axle
Alignment of Front Wheel
Alignment of Front Wheel (SF)

Alignment of Front Wheel

(SF)
1. The following items should be checked to remove the
troubles.
(a) Check the tire abrasion and the air inflation to see it is
suitable or not.
Tire inflation pressure: (250
0)kPa
(b) Check the front wheel bearing to see whether it is loose.
(c) Check the front suspension to see whether it is loose.
(d) Check the steering driving device to see whether it is
loose, and
(e) Check the front vibration through elastic force test to see
whether it is normal in performance.

2. Height adjustment of vehicle

Adjust the vehicle height to the standard value so as to make
the Alignment of Front Wheel inspection.
A-B-58 5mm
A: The height of steering knuckle shaft center.
A B: The center height of the adjusting cam bolt at front end
B
The standard value for the unloaded height is: the
difference of the center height of drive shaft climax and
the front adjusting cam bolt is 58.5mm.

3. Mount on the four wheel locating device

This approach should be conducted according to the detailed
instruction of the equipment manufacturer.

the outer tilt angle of the back tilt angle 4. Adjust the outer tilt angle of front wheel and the back tilt
front wheel of kingpin angle of kingpin
The outer tilt angle of front wheel: 0
5'
0'
The back tilt angle of kingpin: 2
0'
0'
front Outer inclination of front wheel:
 Suspension System and Automobile Axle
Alignment of Front Wheel
Alignment of Front Wheel (SF) SA-7

front cam adjustment In case the outer tilt angle of front wheel or the back tilt angle
of kingpin fails to conform to the specified value, adjust the
cam forward or backward may amend them.

reduce increase

rear cam adjustment

increase reduce

A B B A 5. Wheel angel adjustment

Take apart the limit bolt cap of the steering knuckle to check
the inner wheel steering angle A.
The inner wheel steering angle: =32

Notice:The wheel should not touch the body brake hose
front when the steering wheel is rotated to the bottom.

In case the max steering angle is not in the conformity with the
standard value, adjust the wheel angle through the limit bolts
of steering knuckle.
In case the wheel angle still fails to fall within the standard
range, make a inspection and change the weary and damaged
steering mechanism parts.

6. Wheel toe-in adjustment

Adjust the wheel toe-in according to the following approach
(a) Raise or reduce the vehicle until the suspension stands in
balance.
(b) Push the vehicle on the ground 5 meters forward under
the condition that the front wheels locate forward in a
line.
SA-8 Suspension System and Automobile Axle
Alignment of Front Wheel (SF)

(c) Mark the center of the back of front wheel, and measure
B
the distance ìBî between the remarks on the left and right
tires.

forward

(d) Push the vehicle forward so that the mark on the back of
tire moves to the measuring height of the instrument.
move the vehicle forward Remark: if the tire moves too far, repeat the approach (b).

(e) Measure the distance ìAî between the marks on the front
A
of tire.
(f) Measure the wheel toe-in.
Toe-in = B-A
Inspection standard: (0-2)mm
In case the toe-in fails to conform to the specified value, it can
be amended through adjusting the left and right drag rods.

(g) Loosen the clamping bolt and nut.

(h) Adjust the toe-in situation by the approach of rotating the

left and right drag rod by a same angle.
front
(i) Ensure the left and the right drag rods are same in length.

A B

A=B
 Suspension System and Automobile Axle
Alignment of Front Wheel (SF) SA-9

(j) Tighten the clamping bolts and lock them with split pin.
Remark: the clamping bolt should face the front of the vehicle.

front

(k) Side-slip inspection

Sideslip: =5m/km
SA-10 Suspension System and Automobile Axle (Dr/2WD)
Front Wheel Hub and Steering Knuckle

Front wheel hub and steering knuckle

Element Drawing

Dr

85-105

25-28
front brake shell

front wheel hub snap ring

front wheel hub oil seal

brake caliper

bearing 30205
plain washer

locking nut


98-118
bearing 32007
front wheel hub cap

front wheel hub and

front brake disc stop washer

dust cover

steering knuckle arm

steering knuckle

100-120

132-152

N
m : specific torque

Used component which can not be used any more

Suspension System and Automobile Axle (Dr/2WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub) SA-11

Front Wheel Hub

Disassembly of Front Wheel Hub
1. Take apart the brake caliper.
Disassembly the wheel hub and suspend it with tightwire.
Remark: Donít dismantle the brake hose and brake metal pipe

2. Take apart the front wheel hub cap.

Takeapart the front wheel hub cap from the gap between the
front wheel hub cap and the front wheel hub.

3. Take apart the front wheel hub and front brake disc:
(a) Take apart the split pin to take down the lock cover.
(b) Screw off the lock nuts of the hub bearing with spanner
and take down the stop washer.
(c) Take apart the front wheel hub and front brake disc with
the bearing 30205 together.

4. Take apart the front wheel hub oil seal, the inner race and
roller assembly of bearing 32007.
(a) Pry out the oil seal.
(b) Take out the bearing inner race and roller assembly.

5. Bearing outer race inspection and tear-down

(a) Inspect the bearings
Clean each bearing and check them to see whether there is wear
or damage.
(b) Take apart the bearing outer race
Tap out the bearing outer race with copper bar and hammer.
Notice: bind the disassembled inner and outer bearing
race together to avoid of mixing.
SA-12 Suspension System and Automobile Axle (Dr/2WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub)

6. Inspection and replacement for front brake disc

(a) Check the wear situation of the front brake disc. (see Dr
the brake caliper).
(b) Use the spanner to tear down the bolts that connect the
front wheel hub and the front brake disc.

(c) Connect the front wheel hub and the front brake disc with
bolt and spring washer, and screw up the bolts with a
moment spanner to the specified torque in the diagonal
order.
Fastening torque
(60-79)N
m
(d) Conduct the equilibrium test on the dynamic balancer,
the amplitude value displayed should not be larger than
13.5g under the condition that the measuring rotating
velocity is 796 r/m and the locking rotating velocity is
786 r/m, when the amplitude value is larger than 13.5 g,
encase the counter balanced clip, which is 4 g each, at the
corresponding phase, the number of the clip encased
should not be more than four.
7. Bearing outer race change
Press in the new bearing outer space with the special service
tools.
Notice: the bearing inner and outer races should be changed at
one time.

Assembly of Front Wheel Hub

1. Mount on the Bearing 32007 inner race and roller assem-
bly as well as the front wheel hub oil seal.
Coat the lithium base grease of (4-5)mm on the inner surfaces
of bearing outer race and the front wheel hub, encase the
Bearing 32007 inner race and roller assembly, plaster the
lubricant again. Coat a little lubricant on the lips of front wheel
hub oil seal and then tap it in place.
Notice: do not make the lubricant contact the front brake
disc face.
2. Mount on the Bearing 32007 inner race.
After coating the bearing outer race with the lithium base
grease of 4-5 mm, encase the inner race and roller assembly of
Bearing 30205, and plaster the lubricant again.
Suspension System and Automobile Axle (Dr/2WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub) SA-13

3. Mount the front wheel hub on the steering knuckle.

Coat a little lubricant at the position of the steering knuckle
where the oil seal locates, mount the front wheel hub and front
brake disc on the steering knuckle, and then mount on the stop
washer.
4. Preload adjustment
(a) Mount on the lock nut and screw up according to the
specified torque.
Fastening torque
(130-150)N
m

(b) Run the front wheel hub about 1/4-1/3 of circle, and
combine it with the bearing seat.

(c) Loosen the locking nut to ensure the front brake disc run
freely, and then screw up the nuts to the specified torque.
Fastening torque
(25-35)N
m

(d) Hook the front wheel hub with the spring-tension meter
and pull the spring-tension meter slowly in the tangential
direction of this spot.
The reasonable range of tension force: (16-33)N.
Remark: if the tension force is larger or smaller of the reason-
able range, screw up the nuts again until the tension force falls
within the reasonable range.
(e) Measure the bouncing value of the front brake disc,
which should not be larger than 0.11mm.

5. Mount on the lock cover and the split pin

SA-14 Suspension System and Automobile Axle (Dr/2WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub)

6. Tap in the front wheel hub with a rubber hammer

7. Mount the brake caliper on the steering knuckle.

Fastening torque
(85-105)N
m

Steering Knuckle
Disassembly of Steering Knuckle
1. Take apart the brake caliper, the front wheel hub and the
front brake disc.

2. Take apart the front brake shell:

(a) Tear down the two bolts (M8X16).
(b) Tear down the two split pins, grooved nuts, washer and
bolts that connect the steering knuckle arm.

3. Tear down the steering knuckle

(a) Support the lower arm with jack;
(b) Tear down the two split pins and the grooved nuts
(c) Disconnect the steering knuckle from the upper and
lower ball studs and take apart it.

Inspection on Steering Knuckle

Check the steering knuckle
Check the steering knuckle with the dye penetration agent to
see whether the steering knuckle has a crack or not.
If the crack is found, the steering knuckle is required to be
changed.
Suspension System and Automobile Axle (Dr/2WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub) SA-15

Mount the steering knuckle

1. Mount the steering knuckle
(a) Support the lower arm of the steering knuckle with a jack.
(b) Mount the steering knuckle on the lower ball stud and
screw on the nuts.

(c) Press the upper arm to mount on the steering knuckle and
screw on the nuts.

(d) Screw up the nuts of the upper ball stud according to the
specified torque.
Fastening torque
(100-120)N
m
(e) Screw up the nuts of the lower ball stud according to the
specified torque.
Fastening torque
(98-118)N
m
(f) Mount on the split pin between the upper and lower ball
studs.

2. Mount the steering knuckle arm and the front brake shell;
(a) Screw up the two bolts of M8X16.
Fastening torque
(25-28)N
m
(b) Screw up the two bolts and groove nuts (M12X67) to the
specified torque.
Fastening torque
(98-118)N
m
(c) Mount on the two split pins.
In case the pin hole in the ball stud are not in alignment with
the groove nut, adjust the fastening torque and the rotating
angle under the condition that satisfying the minimum torque,
so as to ensure the torque falls within the specified range, if
cannot, mount the split pin with the minimum torque beyond
the range
3. Mount the front wheel hub and the front brake disc.

4. Check the Alignment of Front Wheel.

(See SA-3)
SA-16 Suspension System and Automobile Axle (Dr/2WD)
Front Suspension

Front suspension
Element figure
Dr

rubber liner assembly for


the upper arm
90
110



pinch gasket of the upper arm shaft bush


110
10
25
28


23
3

transverse
stabilizer rod

 ! torsion bar
23
3
shock


absorber rocker arm

226
25 80
10


80
10

torsion fork

142
10
lower arm

lower ball stud

150
10


65
70

guide lever 96
10

N
m : specified torque

Parts that cannot be reused after being used

Suspension System and Automobile Axle (Dr/2WD)
Front Suspension (Ball Stud) SA-17

Ball stud
Inspection on Ball Stud
1. Check the lower ball stud to see whether it is excessively
loose or not.
(a) Prop up the front of the vehicle with jack and then support
it with the bracket.
(b) Tread down the brake pedal after verifying that the front
wheel are in straight line.
(c) Move the arm vertically to check the lower ball stud to see
whether the clearance is overlarge.
Max vertical clearance : 0.5mm
2. Check the upper ball stud to see whether it is over-loose.
Move the wheel vertically to check whether the clearance of
the ball stud is over large.

3. Check the rotating performance of ball stud

(a) Take apart the ball stud.
(b) Shake the ball stud several times forward and backward
before mounting on the nut, as shown in the drawing.
(c) Rotate the nut continuously with a torsion meter, which
rotates the nut round per 2 to 4 seconds, and read the
reading of the torsion meter after the fifth round.
Fastening torque (running)
Lower ball stud: (0.1-4)N
m
Upper ball stud: (0.1-4)N
m

Disassembly of Ball Stud

1. Tear down the steering knuckle.
(see the SA-14).
2. Take apart the lower ball stud from the lower arm; and

3. Take apart the upper ball stud from the upper arm.
SA-18 Suspension System and Automobile Axle (Dr/2WD)
Front Suspension (Ball Stud)

Mount of Ball Stud

1. Mount the upper ball stud on the upper arm;
Fastening torque
26N
m

2. Mount the lower ball stud on the lower arm;

Fastening torque
65N
m

3. Mount on the steering knuckle

(see page SA-15)
 Suspension System and Automobile Axle (Dr/2WD)
Front Suspension (Torsion Rod Spring) SA-19

Torsion Rod Spring

Dismantle of Torsion Rod Spring
1. Use the jack to raise up the frame and support it with the
bracket.
2. Take apart the locking nuts to measure the length of the
projecting end of the bolts, as shown in the drawing.
Remark: This measuring value can be referred when adjusting
the chassis ground clearance.

3. Take apart the dust cover.

4. Loosen the regulating nut until there is no tension on the
torsion rod spring.

Dr SL SK SY 5. Take apart the torsion arm, torsion rod spring and the
torsion regulating arm.
(a) Tear down the mounting nuts of the torsion rod arm.
(b) Take apart the torsion regulating arm from the adjusting
bolt, the torsion regulating arm should be taken apart with
the torsion rod spring and the torsion rod arm together.

SF

SJ
SA-20 Suspension System and Automobile Axle (Dr/2WD)
Front Suspension (Torsion Rod Spring)

Mount of Torsion rod Spring

Notice: the torsion rod spring marked with
L

(left) or

R
(right), do not mount the springs at the incorrect
location.
1. Mount the torsion rod spring, pedestal arm and torsion arm;
(a) Coat the lithium base grease on the spline of torsion rod
spring.
(b) Align the wide-teeth parts and then mount the pedestal
arm on the torsion rod spring.
(c) Align the wide-teeth parts and then mount the torsion arm
on the torsion rod spring.
(d) Mount the torsion rod spring on the side of torsion arm
and mount on the pedestal arm on the adjusting bolts.
(e) Screw up the torsion arm nuts according to the specified
torque.
Fastening torque
(83
)N
m

(f) Screw up the adjustable nuts so that the protruding length

of the bolt is equal to that before tearing down.

(g) Mount on the wheel and dismantle the bracket, bounce

the vehicle several times so as to make the suspension in
place.
(h) Screw up the adjustable nut to regulate the ground
clearance.


front

2. Tighten the locking nuts according to the specified torque.

Tighten torque
(83
5)N
m

3. Mount on the dust cover.

Suspension System and Automobile Axle (Dr/2WD)
Front Suspension (Lower Arm and Vibration Damper) SA-21

Lower Arm and Vibration Damper

Disassembly of Lower Arm And Vibration
Damper
1. Take apart the torsion rod spring.
(see page SA-19)
2. Take apart the ending part of the torsion rod
(a) Take apart the split pin and nuts.
(b) Take apart the ending part of drag rod.
3. Take apart the vibration damper

4. Take apart the transverse stabilizer rod from the lower

arm.

5. Take apart the guide lever from the lower arm;

6. Take apart the lower ball stud.

SA-22 Suspension System and Automobile Axle (Dr/2WD)
Front Suspension (Lower Arm and Vibration Damper)

7. Take apart the lower arm

Tear down the nuts and lower arm.

Change of Lower Arm Shaft Bush

1. Take down the shaft bush.
(a) Shear off the rubber on shaft bush, as shown in
drawing.
(b) Take apart the shaft bush.

2. Mount the shaft bush.

Mount on the new shaft bush.

Mount of Lower Arm And Vibration

Damper
1. Mount on the lower arm.
Adjust the lower arm in the unloaded stage when screw up the
axial bolts of the lower arm.
Fastening torque
(226
5)N
m

2. Lower ball stud and lower arm connection

Assemble the lower ball stud and lower arm with three bolts.
Fastening torque
65N
m
Suspension System and Automobile Axle (Dr/2WD)
Front Suspension (Lower Arm and Vibration Damper) SA-23

3. Mount the guide lever on the lower arm

Fastening torque
(96
0)N
m

4. Link the transverse stabilizer rod with the lower arm.

Fastening torque
(23
3)N
m

5. Mount the vibration damper.

6. Mount the ending part of the drag rod:

(a) Link the drag rod end to the steering knuckle arm, mount
and screw up the nuts according to the specified torque.
Fastening torque
(91
0)N
m
(b) Lock the nut with the new split pin.

7. Mount the torsion rod spring.

8. Check the Alignment of Front Wheel.
(See the page SA-3)
SA-24 Suspension System and Automobile Axle (Dr/2WD)
Front Suspension (Upper Arm)

Upper Arm
Dismantle of Upper Arm
1. Take apart the ball stud from the upper arm:
(a) Support the upper arm with a jack.
(b) Take apart the four sets of bolt and nut.

2. Take apart the upper arm

(a) Tear down the bolts and adjusting gasket.
(b) Take apart the upper arm.
Remark: Do not lose the adjusting gasket. Write down the
gasket thickness so that it can be mounted on the original place.

Change of the rubber liner of Upper arm

shaft
1. Tear down the rubber liner of the upper arm.
(a) Tear down the bolts and the pinch-off gasket of the upper
arm shaft bush.
(b) Push out the rubber liner of upper arm with tools.

2. Mount the upper arm rubber liner.

(a) Push in the rubber liner of the upper arm with tools.
(b) Mount on the pinch-off gasket of the upper arm shaft
bush and tighten the bolts manually.
Remark: it is not required to screw up the bolts according to the
specified torque.

Mount of Upper Arm

1. Screw up the axle bolts of the upper arm according to
the specified torque,
Fastening torque
(100
0)N
m
Suspension System and Automobile Axle (Dr/2WD)
Front Suspension (Upper Arm) SA-25

2. Mount the upper arm

(a) Mount on the upper arm and the regulating gasket.
(b) Screw up the bolts according to the specified torque.
Fastening torque
(96
0)N
m
Remark: Mount back the gaskets of the same thickness in the
same number on the original locations.

3. Connect the upper ball stud and upper arm together.

Fastening torque
26N
m

4. Check the Alignment of Front Wheel

(See page SA-3)
SA-26 Suspension System and Automobile Axle (Dr/ 2WD)
Front Suspension (Guide Lever)

assembly mark Guide Lever

Disassembly of Guide Lever
1. Mark the assembly mark on the guide lever.

2. Tear down the front fixing nuts from the guide lever.
3. Tear down the guide lever from the lower arm.
Tear down the nuts that fix the guide lever on the lower
swimming arm, and then tear down the guide lever.

assembly mark Mount of Guide Lever

1. Mount on the front fixing nuts
Mount on the front fixing nuts and meanwhile align the
assembly marks on the guide lever.

2. Mount the guide lever on the bracket

(a) Mount the washer and liner on the guide lever, and then
mount the guide lever on bracket.
(b) Mount the sleeve ring, the liner and the washer on the
guide lever.
(c) Screw up the fixing nuts with finger.
3. Mount the guide lever on the lower swing arm.
Screw up the fixing nuts according to the specified torque.
Fastening torque
(96
)N
m

4. Screw up the fixing nuts according to the specified torque,

(a) Dismantle the bracket so that make the vehicle bounce
sever times to put the suspension in balance.
(b) Screw up the front fixing nut.
5. Check the Alignment of Front Wheel
(See Page SA-3)
Suspension System and Automobile Axle (Dr/2WD)
Front Suspension (Transverse Stabilizer Rod) SA-27

Transverse stabilizer rod

Dismantle of Transverse Stabilizer Rod
1. Tear down the torsion rod spring

2. Tear down the transverse stabilizer rod from the lower

swing arm,
(a) Tear down the nuts and cushion blocks that support the
two sides of the stabilizer rod from the lower swing arm
so as to disconnect the stabilizer rod.

(b) Tear down the liner and bracket of the stabilizer rod and
then tear down the stabilizer rod.

Mount of Transverse Stabilizer Rod

1. Put the transverse stabilizer rod on the frame,
Lay the stabilizer rod in place, and mount the stabilizer rod
liner on the bracket, then mount the bracket on frame, finally
screw up the bolts with fingers.
2. Connect the transverse stabilizer rod to the lower swing arm.
Connect the two ends of stabilizer to two lower swing arm with
bolts, cushion blocks and new nuts.
As shown in the drawing, tighten the nuts according to the
specified torque.
Fastening torque
(29
)N
m
3. Screw up the locating bolts according to the specified
torque,
Fastening torque
(29
)N
m
4. Mount on the torsion rod spring.
SA-28 Suspension System and Automobile Axle(SF/2WD)
Front Suspension

Front wheel hub and steering knuckle

Element figures
SF2WD

nut
upper arm transverse stabilizer rod

locking ring
cushion block bolt

cushion block stabilizer rod gasket
123

locking ring rubber
rubber snubber snubber washer
washer Brake
stabilizer rod gasket

caliper
shock absorber restrictor tube
132
152
stabilizer rod gasket

stabilizer rod gasket

steering knuckle

127-147 70-90
lower
ball stud
transverse stabilizer rod gasket

132-152
20-26

brake oil pipe bracket

180
steering
knuckle arm


brake shell

25
29

stop washer

oil seal -front hub lock plate dust cover
liner

front wheel
bearing(inner) 135-155
front wheel hub and 23
29
front brake disc front hub bearing
(outer)

steering knuckle nut
steering knuckle
outer flange cap

N
m :specified torque

Parts that cannot be reused after being used

Suspension System and Automobile Axle (SF/2WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub) SA-29

Front Wheel Hub

Disassembly of Front Wheel Hub
1. Tear down the brake caliper.
(a) Tear down the brake Bundy tube from the brake caliper,
and block the Bundy tube line with a cork.
(b) Tear down the brake caliper from the steering knuckle.

2. Tear down the steering knuckle outer flange cap.

3. Tear down the front wheel hub and brake disc.

(a) Open the lock plate with a screwdriver.
(b) Tear down the steering knuckle nut with the SST tools to
take out the. lock plate
(c) Tear down the other steering knuckle nut with SST tools
to take out the stop washer and the steering knuckle outer
bearing.

(d) Tear down the front wheel hub and the brake disc
assembly.

4. Tear down the front hub, oil seal, front hub bearing
(inner) inner race and roller assembly.
(a) Pry out the oil seal.
Notice: the deformed oil seal should not be reused.
(b) Take out the front hub bearing (inner) inner race and
roller assembly.
SA-30 Suspension System and Automobile Axle (SF/2WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub)

5. Front hub bearing outer race inspection and change

(a) Check each bearing
Wash the inner and outer races of each bearing, and check
them whether they are wearied or damaged.
(b) Tear down the outer race of each bearing.
Tap out the bearing outer race with copper bar and
hammer.
Notice: bind the dismantled inner and outer races of
bearing together to prevent from mixing.

6. Front brake disc inspection and change

(a) Check the wear situation of front brake disc.
(b) Tear down the bolts that connect the front wheel hub and
front brake disc.

(c) Connect the front wheel hub and front brake disc and
screw up the bolts with moment spanner to the specified
torque diagonally
Fastening torque
(70-80)N
m
(d) Conduct the dynamic balance test on the dynamic balancer,
the amplitude value displayed should not be above 13.5g
under the condition that the measuring rotating velocity
is 796 r/m and the locking rotating velocity 786 r/m,
otherwise, tap in the counter balanced clip, which is 4g
each, at the corresponding location, the number of the
clip should not be more than 4.
(e) Tap in the new bearing outer race with the special service
tool.
Notice: the inner and outer races of bearing should be
changed in set.

Assembly of Front Wheel Hub

1. Mount on the inner race and roller assembly of front hub
bearing (inner) as well as the front hub oil seal.
Coat the lithium base grease of 4 to 5 mm on the inside surface of
the bearing outer race and front wheel hub, and plaster the
lubricant in the front hub bearing (inner) and the roller assembly.
Coat a little lubricant on the lips of oil seal of front wheel hub, and
then tap the oil seal of front hub in place with special service tool.
Notice: do not coat the lubricant on the front brake disc face.
Suspension System and Automobile Axle (SF/2WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub) SA-31

2. Mount on the inner race and roller assembly of front hub

bearing (outer).
After coating 4 to 5 mm lithium base grease on the outer race
of bearing, put in the inner race and roller assembly of front hub
bearing (outer), and then plaster the lubricant.

3. Mount the front wheel hub and front brake disc on the
steering knuckle.
Coat a little lubricant on the steering knuckle where the oil seal
locates, and mount the front wheel hub and front brake disc on
the steering knuckle, then mount on the stop washer.
4. Adjust the preload
(a) Mount on the steering knuckle nut and screw up them
according to the specified torque.
Tighten torque: (100-120)N
m

(b) Run the front wheel hub about 1/4-1/3 round, and seat the
bearing.

(c) Loosen the steering knuckle nut to ensure the front brake
disc can run freely. Screw up the steering knuckle nut
again according to the specified torque.
Fastening torque
25N
m
(d) Mount on the lock plate and another steering knuckle nut.
Tighten torque
60N
m

(e) Hold the front wheel hub bolts with a spring-tension

meter and drag the meter slowly in the direction of the
tangent line of this spot.
Suitable tension range: (29-54)N
The nuts should be retightened until falls within the suitable
range if the tension force is overlarge or over small.
(f) Check the bearing and ensure that the clearance, which is
not larger than 0.05 mm, is not excessive.
(g) Measure the bouncing value of the front brake disc face.
Bouncing value should not be above o.11mm.
SA-32 Suspension System and Automobile Axle (SF/2WD)
Front Wheel Hub and Steering Knuckle (Steering Knuckle)

(h) Bend one tooth of the lock plate inside and other teeth
outside to lock the steering knuckle nut.

5. Mount on the liner and the steering knuckle outer flange

cap.
Fastening torque
(23-29)N
m

6. Mount the brake caliper

(a) Mount the brake caliper on the steering knuckle and
screw up the bolts according to the specified torque.
Fastening torque
123N
m
(b) Connect the Bundy tube.
Fastening torque
(20-22)N
m
7. Check the height of the brake liquid level and add the
brake liquid as requirement, exhaust the gas in the
braking system.

Steering knuckle
Dismantle of Steering Knuckle
1. Tear down the brake caliper, front wheel and the front
brake disc.
2. Tear down the dust cover, and the brake shell.

3. Tear down the steering knuckle arm from the steering

knuckle.
Suspension System and Automobile Vehicle (SF/2WD)
Front Wheel Hub and Steering Knuckle (Steering Knuckle) SA-33

4. Tear down the vibration damper from the lower arm.

5. Tear down the transverse stabilizer rod from the lower

arm.

6. Tear down the steering knuckle;

(a) Tear down the split pin and groove nut of upper ball stud.
(b) Take apart the steering knuckle from the upper ball stud
with special service tool.

(c) Tear down the split pin and groove of the lower ball stud.
(d) Take apart the steering knuckle from the lower ball stud
with special service tool.

(e) Press down the lower arm to tear down the steering
knuckle.
SA-34 Suspension System and Automobile Axle (SF/2WD)
Front Wheel Hub and Steering Knuckle (Steering Knuckle)

7. Tear down the lower ball stud assembly from the steering
knuckle.

Inspection on and Change of Steering

Knuckle
1. Check the steering knuckle.
Check the steering knuckle with the dye penetration agent to
see whether there is crack or not.
If crack is found, the steering knuckle is required to be changed.

Mount of Steering Knuckle

1. Mount the lower ball stud on the steering knuckle.
Connect the lower ball stud and steering knuckle with bolts,
which are tightened according to the specified torque.
Fastening torque
(70-90)N
m

2. Mount on the steering knuckle

(a) Press down the lower arm to mount on the steering
knuckle.

(b) Mount on the lower ball stud, groove nut and screw up the
nuts according to the specified torque and then mount on
the split pin.
Fastening torque
(132-152)N
m
Suspension System and Automobile Axle (SF/2WD)
Front Wheel Hub and Steering Knuckle (Steering Knuckle) SA-35

(c) Mount on the upper ball stud and the groove nut that are
screwed up according to the specified torque, and then
split pin.
Fastening torque
(132-152)N
m

3. Mount the stabilizer rod on the lower arm.

Fastening torque
(20-26)N
m

4. Mount the vibration damper on the lower arm.

Fastening torque
(127-147)N
m

5. Mount the steering knuckle arm and the brake oil pipe
bracket on the steering knuckle.
Coat the sealing agent 1271 on the bolt thread.
Fastening torque
180N
m

6. Mount the dust cover and brake shell, and align the
locating hole of the dust cover with the groove of the
steering knuckle to ensure that the dust cover is concen-
tric with the steering knuckle.
Fastening torque
(25-29)N
m
7. Mount the front wheel hub and the front brake disc as well
as the brake caliper.
8. Check the height of brake liquid level and add the brake
liquid as requirement, then exhaust the gas in the brak-
ing system.
SA-36 Suspension System and Automobile Axle(SF/2WD)
Front Suspension

Front Suspension
Elemtents figures
SF

178
15 upper arm shaft bush and tube(long)

upper swing arm

shaft upper arm shaft bush
upper arm shaft pinch-off gasket(large)
bush(short)
torsion bar yoke 89
7

225
5

upper arm shaft bush pinch-off

gasket(small) 27
2

upper arm upper ball stud

transverse
stabilizer rod

142
10
vibration
damper

137
10

23
3

lower arm shaft bush

pinch-off gasket(large)

lower arm shaft bush

pinch-off gasket(small)

lower ball
stud

142
10

eccentric
lower arm
gasket

lower arm shaft bush
and tube 142
10
23
3

N
M : specified torque

Parts that cannot be reused after being used

Suspension System and Automobile Axle (SF/2WD)
Front Suspension (Ball Stud) SA-37

Ball Stud
Inspection on Ball Stud
1. Check the lower ball stud to see whether it is excessively
loose:
(a) Raise the vehicle with a jack and then support it with the
bracket.
(b) Press down the brake pedal after verifying that the front
wheel is straightly forward.
(c) Move the arm vertically to check whether the clearance
of lower ball stud is over large.
(Max vertical clearance): 0.5 mm
2. Check whether the upper ball stud is loose excessively;
Move the wheel vertically to check whether the clearance of
the ball stud is over large.
(Max vertical clearance): 0.5 mm

3. Check the rotating performance of the ball stud:

(a) Tear down the ball stud;
(b) Shake the ball stud column several times before mount-
ing on the nut, as shown in the drawing.
(c) Rotate the nut continuously with the torsion meter at the
speed of one round each 2 to 4 seconds, read the meter
reading at the fifth round.
Fastening torque(running)

lower ball stud
(0.1-4)N
m
Upper ball stud: (0.1-4)N
m

Disassembly of Ball Stud

1. Tear down the steering knuckle, steering knuckle arm
and the lower ball stud assembly.
2. Tear down the ball stud from the steering knuckle;

3. Tear down the ball stud from the upper ball stud.
SA-38 Suspension System and Automobile Axle (SF/2WD)
Front Suspension (Ball Stud
Torsion Rod Spring)

Mount of Ball Stud

1. Mount the upper ball stud on the upper arm;
Fastening torque
(27
)N
m

2. Mount the lower ball stud on the steering knuckle;

Fastening torque
(80
0)N
m

3. Mount on the steering knuckle and hub brake disc

assembly
(See Page SA-34)

Torsion Rod Spring

(see Page SA-19)
Suspension System and Automobile Axle (SF/2WD)
Front Suspension (Lower Arm and Vibration Damper) SA-39

Lower arm and Vibration Damper

Disassembly of Lower Arm
1. Tear down the transverse stabilizer rod;

2. Tear down the vibration damper;

3. Disconnect the lower arm ball stud seat and the lower
ball stud;
Remove the cotter pin and the groove nut.

4. Tear down the lower arm

(a) Make a mark on the mounting position of the eccentric
gasket.

(b) Tear down the lower arm.

SA-40 Suspension System and Automobile Axle (SF/2WD)
Front Suspension (Lower Arm and Vibration Damper)

Change of Lower Arm Shaft Bush and Tube

1. Tear down the lower arm shaft bush and shaft tube:
(a) Tear down the large and small pinch-off gaskets of the
lower arm shaft bush first.
(b) Tear down the lower arm shaft bush and tube.

2. Mount the lower arm shaft bush and tube.

(a) Press down the lower arm shaft bush and tube.
(b) Press down the large and small pinch-off gaskets of the
lower arm shaft bush.

Mount of Lower Arm

1. Mount on the lower arm
Align the marks on the eccentric gasket and on the frame, and
then screw up the lower arm bolt.

2. Connection for lower ball stud and lower arm:

Mount the lower ball stud and the lower arm ball stud seat
together.
Fastening torque
(142
0)N
m

3. Vibration damper mount

Mount the vibration damper on the lower arm bracket;
Fastening torque
(137
0)N
m
Suspension System and Automobile Axle (SF/2WD)
Front Suspension (Lower Arm and Vibration Damper) SA-41

4. Mount the transverse stabilizer rod on the lower arm;

Fastening torque
(23
)N
m

5. Check the Alignment of Front Wheel;

(See Page SA-6)
SA-42 Suspension System and Automobile Axle (SF/2WD)
Front Suspension (Upper Arm)

Upper Arm
Dismantle of Upper Arm
1. Tear down the torsion rod spring:
(See page SA-19)

2. Tear down the upper ball stud:

(a) Support the upper arm with a jack.
(b) Tear down the four sets of bolt and nut.

3. Upper arm dismantle

Tear down the bolts to take down the upper arm.

Change of the Upper Arm Shaft Bush

(Short) and the Upper Arm Shaft Bush
and Tube
1. Tear down the upper arm shaft bush (short) and the
upper arm shaft bush and tube (long)
(a) Tear down the torsion bar yoke, the nuts as well as the
large and small pinch-off gaskets of the upper arm shaft
bush.
(b) Push out the upper arm shaft bush (short) and upper arm
shaft bush and tube.
2. Mount on the upper arm shaft bush (short) and the upper
arm shaft bush and tube (long):
(a) Press the upper arm shaft bush and tube (long) in the
upper arm, and encase the upper swing arm shaft, and
then encase the upper arm shaft bush (short).
(b) Mount on the large and small pinch-off gaskets of upper
arm shaft bush and screw up the nuts.
Fastening torque
(225
)N
m

(c) Mount on the torsion bar yoke.

Notice: the notch of torsion bar yoke should face
downward;
Fastening torque
(89
)N
m
Suspension System and Automobile Axle (SF/2WD)
Front Suspension \(Lower arm, Guide Lever and Transverse Stabilizer Rod) SA-43

Mount of Upper Arm

1. Screw up the axle nut of upper arm according to the
specified torque;
Fastening torque
(225
)N
m

2. Mount on the upper arm;

Screw up the three bolts of the upper swing arm shaft according
to the specified torque;
Fastening torque
(178
5)N
m

3. Connect the upper arm ball stud with the upper arm;
Use four sets of bolt and nut to connect the upper arm ball stud
and the upper arm.
Fastening torque
(27
)N
m

4. Mount the torsion rod spring;

5. Check the Alignment of Front Wheel:

(See Page SA-6)

Guide Lever
(See page SA-26)

Transverse Stabilizer rod

(See page SA-27)
SA-44 Suspension System and Automobile Axle (SF/4WD)
Front Wheel Hub and Steering Knuckle

Front Wheel Hub and Steering Knuckle

Element Figure
SF 4WD

nut upper arm

transverse stabilizer rod

lock ring
cushion block bolt
lock ring
transverse stabilizer 123
cushion rod gasket

block rubber snubber
rubber washer
snubber transverse stabilizer
shock washer rod gasket
brake
absorber
stabilizer rod limit tube caliper
132-152 transverse stabilizer

rod gasket

transverse stabilizer rod gasket

constant speed steering knuckle
drive shaft needle

inner oil bearing
seal- drive shaft
steering knuckle
127-147 small sleeve
lower ball stud


70-90 retainer ring
transverse stabilizer rod gasket

132-152 thrust plate-
20-26 steering knuckle
brake oil pipe bracket

washer-spline of
180 steering knuckle
steering shaft
knuckle arm


brake shell
25-29

stop washer

oil seal - lock plate dust cover
front hub liner

front hub bearing

(inner) 135-155
front wheel hub and 25-29
front brake disc
front hub bearing
(out) gasket
steering knuckle
big nut
free wheel hub 6-12
noumenon gasket

free wheel
hub cap
N
m
specified torque

Parts that cannot be reused after being used

Suspension System and Automobile Axle (SF/4WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub) SA-45

Front Wheel Hub

Disassembly of Front Wheel Hub
1. Tear down the brake caliper:
(a) Tear down the Bundy tube from the brake caliper and
block the pipeline of Bundy tube with cork.
(b) Tear down the brake caliper from the steering knuckle.

2. Tear down the free hub.

3. Tear down the retainer ring and the axle spine of washer-
steering knuckle:
Tear down the retainer ring with the pliers for retainer ring, and
take down the axle spline of washer-steering knuckle by hand.

4. Tear down the front wheel hub and front brake disc:
(a) Prize up the lock plate with screwdriver.
(b) Tear down the steering knuckle nut with special service
tool to take out the lock plate.
(c) Tear down another steering knuckle nut with special
service tool to take out the stop washer.

(d) Tear down the front wheel hub and the front brake disc.
SA-46 Suspension System and Automobile Axle (SF/4WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub)

5. Tear down the front hub, the oil seal and the inner race
of front hub bearing (inner)
(a) Prize out the oil seal.
(b) Take out the inner race of front hub bearing (inner).

6. Inspection on and change of the outer race of front hub

bearing
(a) Check each bearing:
Wash the inner and outer races of each bearing to check
their wear or damage situation.
(b) Tear down the outer race of each bearing:
Tap out the outer bearing race with copper bar and hammer.
Notice: bind the inner and outer races of the same
bearing together to prevent from mixing.

7. Inspection and change for front brake disc

(a) Check the wear situation of the front brake disc.
(b) Tear down the bolts that connect the front wheel hub and
the front brake disc.

(c) Connect the front wheel hub and the front brake disc with
bolts, which are tightened diagonally with moment span-
ner according to the specified torque.
Fastening torque
(70-80)N
m
(d) Make the dynamic balance test on the dynamic balancer,
and the amplitude value displayed should not be smaller
than 13.5g under the condition that the measuring rotat-
ing velocity is 796 r/m and the locking rotating velocity
of 786 r/m, otherwise, tap the counter balanced clip,
which is 4g each, in the corresponding position, the clip
number should not be more than 4.

(e) Tap in the new bearing outer race carefully with the
special service tool.
Notice: the inner and outer races of the same bearing
should be changed in one time.
Suspension System and Automobile Axle (SF/4WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub) SA-47

Assembly of Front Wheel Hub

1. Mount on the inner race and roller assembly of front hub
bearing as well as the oil seal of front hub.
Coat the lithium base grease of (4-5)mm on the inside surfaces
of the bearing outer race and the front wheel hub, put in the
inner race and roller assembly of front hub bearing (inner),
then plaster the lubricant. Plaster a little lubricant on the lips of
front wheel hub oil seal, and finally tap the front hub in place
with special service tool.
Notice: Do not plaster the lubricant on the face of front
brake disc.
2. Mount the inner race of front hub bearing (outer) and
roller assembly
Coat 4
5 mm of lithium base grease on the outer race of
bearing, and then put the inner race of front hub bearing (outer)
and roller assembly in it, finally plaster with lubricant.

3. Mount the front wheel hub on the steering knuckle

Coat a little lubricant on the oil seal of steering knuckle, and
then mount the front wheel hub and front brake disc on the
steering knuckle, finally mount on the stop washer.
4. Adjust preload:
(a) Mount on the steering knuckle nut and screw it up
according to the specified torque.
Fastening torque
(100-120)N
m

(b) Run the front wheel hub by 1/4-1/3 round so as to seat the
bearings.

(c) Loosen the steering knuckle nut to ensure the front brake
disc can run freely. Screw up the steering knuckle nut
again to the specified torque.
Fastening torque
25N
m
(d) Mount on the lock plate and mount on another steering
knuckle nut.
Fastening torque
60N
m
SA-48 Suspension System and Automobile Axle (SF/4WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub)

(e) Hold the bolt of front wheel hub with the spring-tension meter
and drag slowly in the direction of the spot tangent line.
Suitable tension range
(29-54)N
The nut should be screwed up again within the suitable range if the
tension value is overlarge or over small.
(f) Check the bearing to ensure it cannot leap excessively (the
axial clearance should not be more than 0.05mm).
(g) Measure the bouncing value of the front brake disc, which
should not be more than 0.11mm, and

(h) Bend one tooth of lock plate inside and other teeth outside
so as to lock the steering knuckle nut.

5. Mount the liner and the free hub:

(a) Tear down the free wheel hub cap firstly.
(b) Mount the liner and the free hub on the front wheel hub.
Fastening torque
(25-29)N
m

(c) Mount on the free wheel hub cap.

Fastening torque
(6-12)N
m

6. Mount the brake caliper:

(a) Mount the brake caliper on the steering knuckle and screw
up the bolts according to the specified torque.
Fastening torque
123N
m
(b) Connect the Bundy tube.
Fastening torque
20-22N
m
7. Check the height of brake liquid level and, if required, add
the brake liquid, exhaust the gas from the brake system.
Suspension System and Automobile Axle (SF/4WD)
Front Wheel Hub and Steering Knuckle (Steering Knuckle) SA-49

Steering Knuckle
Dismantle of Steering Knuckle
1. Tear down the brake caliper, he front wheel and the front
brake disc.
2. Tear down the dust cover and the brake shell;

3. Tear down the steering knuckle arm from the steering

knuckle;

4. Tear down the vibration damper from the lower arm;

5. Tear down the transverse stabilizer rod from the lower

arm;

6. Tear down the steering knuckle:

(a) Tear down the split pin and groove nut from the position
where the ball stud locates.
(b) Tear down the steering knuckle from the position where
the ball stud locates with the special service tool.
SA-50 Suspension System and Automobile Axle(SF/4WD)
Front Wheel Hub and Steering Knuckle (Steering Knuckle)

(c) Tear down the split pin and groove nut from the position
where the lower ball stud.
(d) Tear down the steering knuckle from the position where
the lower ball stud with the special service tool, and

(e) Press down the lower arm to tear down the steering
knuckle.

7. Tear down the Lower ball stud assembly from the posi-
tion where the steering knuckle locates.
Steering knuckle inspection and change

Inspection on and Change of Steering

knuckle
1. Check the steering knuckle
Check the steering knuckle with the dye penetration agent to
see weather has crack, if any crack is found, change the
steering knuckle.

2. Tear down the inner oil seal
drive shaft and the thrust
plate
steering knuckle.
Prize out the inner oil seal
drive shaft from the steering
knuckle with the screwdriver to take out the thrust plate

steering knuckle.
Suspension System and Automobile Axle(SF/4WD)
Front Wheel Hub and Steering Knuckle (Steering Knuckle) SA-51

3. Tear down the needle bearing;

Tap out the steering knuckle small sleeve with hammer and
copper.

4. Tear down the needle bearing.

Tap out the needle bearing with the hammer and copper bar.

5. Mount the steering knuckle small sleeve;

Tap in the steering knuckle small sleeve with the special
service tool.

6. Mount on the needle bearing;

Tap in the needle bearing with the special service tool.

7. Mount on the thrust plate- steering knuckle;

Coat the needle roller of the needle bearing with the lithium
base grease, and plaster the lubricant on the both sides of the
thrust plate ñsteering knuckle.
SA-52 Suspension System and Automobile Axle (SF/4WD)
Front Wheel Hub and Steering Knuckle (Steering Knuckle)

8. Mount the inner oil seal óon the steering knuckle.

Check the oil seal visually, if any deformation or glue lack is
found, change the oil seal

Mount of Steering Knuckle

1. Mount the lower ball stud on the steering knuckle;
Connect the lower ball stud and the steering knuckle with
bolts, and screw up the bolts according to the specified torque.
Fastening torque
(70-90)N
m

2. Mount on the steering knuckle

(a) Coat the lubricant HP-R on the drive shaft.
(b) Press down the lower arm to mount on the steering
knuckle.

(c) Mount on the groove nut of lower ball stud and screw up
the nut according to the specified torque, and then mount
on the split pin.
Fastening torque
(132-152)N
m

(d) Mount on the groove nut of upper ball stud and screw up
the nut according to the specified torque, and then mount
on the split pin.
Fastening torque
(132-152)N
m
Suspension System and Automobile Axle (SF/4WD)
Front Wheel Hub and Steering Knuckle (Steering Knuckle) SA-53

3. Mount the stabilizer rod on the lower arm.

Fastening torque
(20-26)N
m

4. Mount the vibration damper on the lower arm.

Fastening torque
(127-147)N
m

5. Mount the steering knuckle arm and the brake oil pipe
bracket on the steering knuckle, and coat the sealing
agent 1271 on the bolt thread.
Fastening torque
180N
m

6. Mount on the dust cover and the brake shell.

Align the locating hole of dust cover and the groove of the
steering knuckle so as to guarantee the dust cover and the
steering knuckle are concentric.
Fastening torque
(25-29)N
m
7. Mount the front wheel hub and the front brake disc as well
as the brake caliper.
8. Check the height of the brake liquid level and, if required,
add the brake liquid, exhaust the gas of the braking
system.
SA-54 Suspension System and Automobile Axle (SF/4WD)
Constant Speed Drive Shaft

Constant Speed Drive Shaft

Element figure
SF4WD

axially movable three-ball

universal joint front drive axle shaft
sleeve assembly

front speed reducer and

differential assembly

mobile joint
snapping ring
triangular joint

extensible-end large
gripping hoop constant speed
drive shaft

extensible-end
dust cover
extensible-end small
gripping hoop

shaf

fixed-end small gripping hoop

fixed-end dust cover

fixed-end large gripping hoop

steel retainer ring

ball-cage type universal joint

inner oil seal- drive shaft

N
M
specified torque

Parts that cannot be reused after being used

Suspension System and Automobile Axle (SF/4WD)
Constant Speed Driving Shaft SA-55

Disassembly of Constant Speed Driving

Shaft
1. Tear down the brake caliper.

2. Tear down the free hub

3. Tear down the retainer ring from the drive shaft with the
calipers, and take down the washer-steering knuckle
shaft spline.

4. Tear down the front wheel hub and the steering knuckle
together.

5. Screw off the nuts that connect the constant speed drive
shaft to take down the constant speed drive shaft.

6. Check and repair the constant speed drive shaft

Inject the molybdenum disulphide lithium grease of 100-110
g in the end of ball-cage type universal joint and the end of
axially movable tripod universal joint.
The ball-cage type universal joint and the axially movable
tripod universal joint should swing freely, and no clipping
stagnant is allowed. The dust cover should be prevented from
deformation and every gripping loop shall be clamping tightly.
SA-56 Suspension System and Automobile Axle (SF/4WD)
Constant Speed Driving Shaft

Mount of Constant Speed Drive Shaft

1. Mount the constant speed drive shaft on the flanges of
the long and short axle shafts.

2. Mount on the front wheel hub and the steering knuckle.

3. Mount on the washer-steering knuckle shaft spline, and

then use the caliper to mount on the retainer ring.

4. Mount on the free hub.

5. Mount on the brake caliper.

Suspension System and Automobile Axle (SF/4WD)
Front Speed Reducer (Change of Driving Bevel Gear Oil Seal of Front Speed Reducer) SA-57

Front Speed Reducer

Change of driving bevel gear oil seal of front speed reducer

140-210
main-tooth nut
oil-guard tray

flange and dust cover

driving bevel gear oil seal

front speed reducer and

differential assembly

N
M
specified torque

Parts that cannot be reused after being used

1. Support up the front of vehicle to tear down the front

wheel and the steering knuckle.
2. Drain off lubricant in the front speed reducer.
3. Disconnect the front speed reducer flange and the drive
shaft.
Notice: Mark the assembly marks on the speed reducer
and the drive shaft before disconnecting them.
4. Tear down the front speed reducer.

5. Tear down the flange and dust cover:

(a) Loosen the riveted position on main-tooth nut with the
hammer and chisel.
SA-58 Suspension System and Automobile Axle (SF/4WD)
Front Speed Reducer (Change of Driving Bevel Gear Oil Seal of Front Speed Reducer)

(b) Lock the flange with special service tool to tear down the
main-tooth nut.

(c) Tap down the flange and dust cover with copper bar.

6. Tear down the driving bevel gear oil seal and oil-guard
tray:
(a) Tear down the driving bevel gear oil seal with special
service tool.
(b) Tear down the oil-guard tray.

7. Tear down the inner race of conical roller bearing;

If the bearing is damaged, change a new bearing.

8. Mount the new bearing.

Suspension System and Automobile Axle (SF/4WD)
Front Speed Reducer (Change of Driving Bevel Gear Oil Seal of Front Speed Reducer) SA-59

9. Mount the new driving bevel gear oil seal:

(a) Encase the oil-guard tray.
(b) Press the new oil seal in the speed reducer shell with the
special service tool; the mounted oil seal should be 1.5
mm away from the end face of the housing.
Notice: Coat the lithium base grease evenly on the lips of
oil seal.

10. Mount the flange and dust cover:

(a) Encase the flange and dust cover in the front speed
reducer shell through the clinch of oil seal.

(b) Lock the flange with the special service tool and screw up
the nuts according to the specified torque.
Fastening torque
(140-210)N
m

11. Adjust the preload of driving bevel gear bearing

Measure the play preload between the driving bevel gear and
the driven bevel gear with the torque tester.
Preload:(1.8-2.4)N
m
Remark: if the requirement is not satisfied, change the
adjusting washer between the adjusting washer jackets and
bearing 32307, see the disassembly and assembly for front
speed reducer, until the requirement is satisfied.
(a) If the preload is larger than the specified value, change
with a thicker adjusting washer;
(b) If the preload is smaller than the specified value,
change with a thinner adjusting washer.

12. Rivet the main-tooth nut.

SA-60 Suspension System and Automobile Axle (SF/4WD)
Front Speed Reducer (Change of Driving Bevel Gear Oil Seal of Front Speed Reducer)

13. Mount the front speed reducer assembly on the frame.

14. Connect the drive shaft to the flange:

(a) Align the assembly mark and then connect the drive
shaft and the front drive axle flange with four sets of
bolt and nut.
(b) Screw up the nuts according to the specified torque.
Specified torque
(69-79)N
m
Suspension System and Automobile Axle (SF/4WD)
Front Speed Reducer (DisassEmbly of Front Speed Reducer) SA-61

Dismantle of Front Speed Reducer

constant speed drive shaft

front drive axle shaft

sleeve assembly

front drive axle hanger

rubber jacket and

shaft tube

front speed reducer and

differential assembly

constant speed
drive shaft

front speed reducer shell hanger

N
M
cpecified torque

Parts that cannot be reused after being used

SA-62 Suspension System and Automobile Axle (SF/4WD)
Front Speed Reducer (DisassEmbly of Front Speed Reducer)

1. Disconnect the front speed reducer flange and the drive

shaft.

2. Screw off the nuts that connect the constant speed drive
shaft.

3. Screw off the bolts connecting the rubber jacket and

shaft tube of the front speed reducer cover and the
frame.

4. Screw off the bolts connecting the front drive axle hanger
assembly and the front speed reducer shell hanger, and
tear down the front speed reducer.
Suspension System Automobile Axle (SF/4WD)
Front Speed Reducer (Change of Axle Shaft Oil Seal) SA-63

Change of Axle Shaft Oil Seal

snapping ring

oil seal-front half-shaft

front minor half-shaft
88

snapping ring

front speed reducer and differential

N
M
specified torque front long

semi-axis

Parts that cannot be reused after being used)

1. Tear down the front long semi-axis and the front minor
half-shaft
Pull out the front long and minor semi-axis from the front
speed reducer with tool.

2. Tear down the front drive axle shaft sleeve and screw off
the bolts connecting the half-shaft sleeve.

3. Tear down the oil seal - front half-shaft:

Tear down the oil seal-front half-shaft with the special service
tool.
SA-64 Suspension System Automobile Axle (SF/4WD)
Front Speed Reducer (Change of Axle Shaft Oil Seal)

4. Mount on the new oil seal-front half-shaft:

Press in the new oil seal with the special service tool until it
flush with the outer ending of the oil seal, coat moderate
lubricant on the lips of the oil seal.

5. Mount on the upper front drive axle shaft sleeve,

Coat the bolt thread with thread locking agent.
Fastening torque
88N
m

6. Mount on the front long semi-axis and the front minor

half-shaft.
(a) Mount the new snapping ring on the half-shaft.
(b) Mount on the long semi-axis and the minor half-shaft
with the special service tool.
Suspension System Automobile Axle (SF/4WD)
Front Speed Reducer (Disassembly and Assembly of Front Speed Reducer) SA-65

Disassembly and Assembly of Front Speed Reducer

Element figure

oil seal-front half-shaft

flange and dust cover
front speed bearing 31306
front minor half-shaft reducer shell
oil-guard tray

snapping ring

bearing 32307

140-210
driving bevel gear oil seal

driving bevel gear oil seal

oil seal-front half-shaft

jacket

adjusting washer
adjusting washer

speed reducer cover

47
snapping ring
retainer ring
bearing 50KB801 bearing B36Z-10

adjusting washer

cap-differential front long semi-axis

bearing
78 70-90

lock plate

front differential housing

half axle gear thrust
gasket

pin
planetary gear axle driven bevel gear

planetary gear shaft

planetary gear stop gasket

half-axle gear

adjusting gasket
N
M
specified torque

Parts that cannot be reused after being used

SA-66 Suspension System Automobile Axle (SF/4WD)
Front Speed Reducer (Disassembly and Assembly of Front Speed Reducer)

Disassembly of Front Speed Reducer

1. Tear down the speed reducer cover:
Screw off the eight bolts connecting the speed reducer cover.

2. Tear down the front long semi-axis and the front minor
half-shaft:
Tear down the front long semi-axis and the front minor half-
shaft from the speed reducer assembly with the special service
tool.

3. Tear down the front drive axle shaft sleeve

Screw off the four bolts connecting the front drive axle shaft
sleeve.

4. Tear down the oil seal ó front half-shaft;

Tear down the oil seal ófront half shaft with the special service
tool.

5. Check the swing difference of the axle driven bevel gear;

Run the flange to measure the axle driven bevel gear with the
dial-indicating lamp.
Swing difference)
0.07mm
Max swing difference: 0.07 mm
In case the swing difference is more than 0.07 mm, change the
compete package of driven bevel gear.
Suspension System Automobile Axle (SF/4WD)
Front Speed Reducer (Disassembly and Assembly of Front Speed Reducer) SA-67

6. Check the teeth-clearance of the driving bevel gear and

the axle driven bevel gear:
(a) Install the dial-indicating lamp and ensure the axial line
of measuring head is vertical with the contact teeth face.
(b) Run the flanges, and record the clearance values of
driving bevel gear and the axle driven bevel gear.
Specified clearance range
(0.15-0.25)mm
Remark: the inspection should be conducted at no less than
three equally divided spots on the circumference of the axle
driven bevel gear.
7. Check the engagement trace of the axle driven bevel
gear.
(See page SA-76)

8. Tear down the flange and dust cover:

(a) Loosen the riveted position of main-tooth nut with the
hammer and chisel.

(b) Lock the main-tooth flange with SST to tear down the
main-tooth nut.

(c) Tap down the driving bevel gear flange and dust cover
with copper bar.
SA-68 Suspension System Automobile Axle (SF/4WD)
Front Speed Reducer (Disassembly and Assembly of Front Speed Reducer)

9. Tear down the driving bevel gear oil seal and the oil-
guard tray:
(a) Tear down the oil seal from the driving bevel gear with
SST.
(b) Take out the oil-guard tray.

10. Tear down the inner race of bearing 31306 with SST;
If the bearing is damaged, change with a new bearing.

11. Tear down the cap-differential bearing.

12. Take out the differential.

13. Take down the outer race of bearing 50KB801 and mark
right clearly the left and right parts to avoid of confusion during
reassembling.

left

14. Tear down the adjusting gaskets and clearly mark the left
right and right to avoid of confusion during re-assembling.

left
Suspension System Automobile Axle (SF/4WD)
Front Speed Reducer (Disassembly and Assembly of Front Speed Reducer) SA-69

15. Tear down the driving bevel gear.

Inspection on and Change of Front Speed

Reducer
1. Change the bearing 32307 on driving bevel gear
(a) Press out the inner race and roller assembly of bearing
32307 with the special service tool.

(b) Press in the new inner race and roller assembly of bearing
32307 with SST.

2. Change the outer race of bearing 32307:

(a) Tap down the outer race of bearing 32307 with the copper
bar and hammer.

(b) Press in the new outer race of bearing 32307 with the
SST.
SA-70 Suspension System Automobile Axle (SF/4WD)
Front Speed Reducer (Disassembly and Assembly of Front Speed Reducer)

3. Change the outer race of bearing 31306:

(a) Tap down the outer race of bearing 31306 with copper bar
and hammer.

(b) Press in the new outer race of bearing 31306 with SST.
Remark: the inner race of the bearing should be changed with
the outer race together.

4. Tear down the inner race and roller assembly of the two
bearings 50KB801 from the differential housing.
Tear down the inner race and roller assembly of bearing
50KB801 with SST.

5. Tear down the axle driven bevel gear:

Tear down the bolts and lock plate by tapping lightly the axle
driven bevel gear with the copper until tear them down.

6. Differential disassembly
(a) Tap out the pin with SST.
Suspension System Automobile Axle (SF/4WD)
Front Speed Reducer (Disassembly and Assembly of Front Speed Reducer) SA-71

(b) Tear down the planetary gear shaft to take out the planetary
gear, planetary gear stop gasket, half-axle gear and the
half axle gear thrust gasket

7. Differential assembly mount

(a) Clean the differential housing.
(b) Encase the half-axle thrust gasket in the differential
housing after covering on the half-shaft gear.

(c) Run the half-axle gear to encase the planetary gear and
planetary gear stop gasket, and put on the planetary gear
shaft.
Remark: The half-axle gear and the planetary gear should run
freely without stagnant.

(d) Measure the clearance between the half axle gear thrust
gasket and differential housing.
Push the planetary gear to the inside and then measure
the clearance between half-axle gear thrust gasket and
the differential housing with the dial-indicating lamp.
Suitable clearance range: (0.4-0.75)mm
Remark:If the clearance fails to fall within the above-
mentioned range, change the half-axle gear thrust gasket,
and ensure that the thrust gaskets on the both sides are
same thick.
(e) Tap the pin in the pinhole of differential housing and the
planetary gear shaft with SST, and rivet the hole port so
as to prevent the pin from missing.
SA-72 Suspension System and Automobile Axle (SF/4WD)
Front Speed Reducer (Disassembly and Assembly of Front Speed Reducer)

(f) Clean the differential housing surface, mount the axle

driven bevel gear on the differential housing with copper
bar.
Notice: align the assembly marks made when
disassembling when mounting the axle driven bevel
gear, and tap in the driven bevel gear evenly alongside
the direction of circumference.

(g) Mount on the lock plate and screw on the bolts, then lock
the lock plate with the drift pinch and hammer.
Fastening torque
(70-90)N
m
Notice: the bolts should be screwed up in the diagonal
order in such manner that tighten a little at first, and then
screw up evenly to the specified torque, the lock plate
claw should contact closely the side face of bolt head.

(h) Press the inner race and roller assembly of bearing

50KB801 in the bearing position at the both sides of
differential housing.

(i) Put the adjusting gasket in the outer position of the side
bearing of front speed reducer shell.

(j) Encase another adjusting gasket with the outer race of

bearing 50KB801 in the front speed reducer shell to-
gether with the differential.

(k) Mount on the right and left cap-differential bearing, and

screw up the bolts with spanner according to the specified
torque.
Fastening torque
78N
m
Suspension System and Automobile Axle (SF/4WD)
Front Speed Reducer (Disassembly and Assembly of Front Speed Reducer) SA-73

(l) Run the flange to check the swing difference of axle

driven bevel gear.
Max swing difference
0.07mm
Remark: if the requirement is not satisfied, tear down the axle
driven bevel gear from the differential, and then screw up the
bolts again.

8. Change the bearing of the long semi-axis:

(a) Take down the retainer ring with the calipers.

(b) Tear down the grooved ball bearing from the long semi-
axis.

(c) Mount on the new grooved ball bearing on the long semi-
axis
(d) Mount on the retainer ring with calipers.
SA-74 Suspension System and Automobile Axle (SF/4WD) Front Speed Reducer (Assembly of Front Speed Reducer)

Assembly of Front Speed Reducer

1. Clean the front speed reducer shell; press the outer
races of bearing 31306 and bearing 32307 to mount
them in the speed reducer shell.
2. Mount he inner race and roller assembly of bearing
31306 as well as the oil-guard tray in the front speed
reducer shell, then press on the driving bevel gear oil
seal with SST.
Notice: coat a little lubricant on the lip open of the oil seal
before encasing it, and the oil seal that is encase in the
front speed reducer shell should be 1.5 mm away from
housing faces.
3. Encase the flange and dust cover in the front speed
reducer through the lip open of oil seal and press it by
hand.

4. Select the adjusting washer ñdriving bevel gear accord-

ing to the experience, and cover it on the driving bevel
gear; and mount the inner race and roller assembly of
bearing 32307 on the driving bevel gear by pressing.
5. Mount the adjusting washer and sleeve on the driving
bevel gear, and encase it in the front speed reducer cell
through the flange along with the spline, and screw on
the nuts.

6. Screw up the main-tooth nuts to the specified torque with

the SST.
Fastening torque
(175
35)N
m

7. Measure the preload on the driving bevel gear bearing

with torque tester :
New bearing
(1.2-1.7)N
m
Old bearing
(0.9-1.3)N
m
Suspension System and Automobile Axle (SF/4WD)
Front Speed Reducer (Assembly of Front Speed Reducer) SA-75

8. Encase in the differential:

(a) Put the adjusting gasket in the outer position of bearing
at the side of the front speed reducer shell, and then
Encase the differential in the front speed reducer shell, be
sure there is a play between the driving gear and the
driven gear.

(b) Tap the axle driven bevel gear with the rubber hammer,
so that the bearing 50KB801 on the differential, together
with the adjusting gasket, contact the mounting part of
the side face of speed reducer closely.

9. Measure the clearance between the axle driven bevel

gear and the driving bevel gear with the dial indicator to
select the adjusting gasket that satisfy the reasonable
play of (0.15-0.25)mm.

10. Select the adjusting washer for the other side:

The thickness of adjusting gasket should eliminate the clear-
ance between the bearing 50KB801 and the front speed re-
ducer shell, on the other side, the adjusting gasket should not
be over thick because the over-thick gasket will lead in too
large pre-tightening force on the bearing 50KB801 of
differential.

11. Tear down the adjusting gasket and differential, and

encase the new adjusting gasket in the front speed
reducer shell, and another adjusting gasket, together
with the differential housing, should be encased in the
front speed reducer shell correctly.
SA-76 Suspension System and Automobile Axle (SF/4WD)
Front Speed Reducer (Assembly of Front Speed Reducer)

12. Measure the clearance between the axle driven bevel

gear and the driving bevel gear with dial indicating lamp.
Clearance: 0.15-0.25mm
Remark: if the play fails to fall within the specified range,
change with the adjusting gasket of other thickness to satisfy
the requirement under the precondition there is no clearance
between the adjusting gasket and the differential.

13. Mount on the left and the right cap-differential bearing:

Screw up the bolts with spanner to the specified torque;
Fastening torque
78N
m

14. Measure the total preload of the front speed reducer with
torque tester;
Fastening torque
(1.8-2.4)N
m

15. Check the teeth engagement between the axle driven

bevel gears:
(a) Coat three or four teeth at three different positions of the
axle driven bevel gear in red
(b) Hold the flange tightly while rotating the axle driven
bevel gear.

(c) Check the teeth engagement situation.

Remark: the trace of the teeth of axle driven bevel gear should
satisfy this requirement. Otherwise, select the suitable adjust-
ing washer for correcting according to the situation of poor
teeth engagement;
Select the adjusting gasket that makes the main teeth apart
from the axle driven bevel gear.
convex surface of gear concave surface of gear
Suspension System and Automobile Axle (SF/4WD)
Front Speed Reducer (Assembly of Front Speed Reducer) SA-77

heel end engagement tooth top engagement

Select the adjusting gasket that make the main teeth contact
closer with the axle driven bevel gear.

toe end engagement tooth top engagement

Select the adjusting gasket that make the main teeth contact farther with the axle driven bevel gear.

(d) Tear down the bearing 32307 from the driving bevel gear
and change the adjusting washer.
(e) Re-measure the total preload of the front speed reducer
and the situation of teeth engagement until they satisfy
the requirement.

16. Rivet the main-tooth nut;

17. Mount on the new oil seal ó front half-shaft;

Press in the new oil seal with the SST until it flush with the
outer face of the oil seal, coat the moderate lubricant on the
position of oil seal and on the lip open of oil seal.
SA-78 Suspension System and Automobile Axle (SF/4WD)
Front Speed Reducer (Assembly of Front Speed Reducer)

18. Mount on the front drive axle shaft sleeve;

Notice: Thread locking agent should be coated on the
bolt thread.
Fastening torque
88N
m

19. Mount on the front long semi-axis and the front minor
half-shaft.
(a) Mount the new snapping ring on half-shaft.
(b) Mont on the front semi-axis and the front minor half-
shaft.

20. Mount the front speed reducer shell assembly:

(a) Clear the front speed reducer shell and the contact face of
front speed reducer shell;
(b) Coat the glue line with diameter of 2-3 mm, and the glue
line should be even and without fracture.
Remark: The front speed reducer shell should be mounted
ready within 15 min after coating the glue.
(c) The bolts, before screwed up, should be coated with
thread locking sealing agent and screwed up to the
specified torque.
Fastening torque
47N
m
 Suspension System and Automobile Axle (rear)
Rear Axle Shaft SA-79

Rear Axle Shaft

Element figure

rear brake brake drum

O rubber O-ring seal

rear axle housing

bearing seat
oil seal of rear
liner half-shaft
inner oil seal seat of wheel bearing
rear wheel bearing

grooved ball
bearing oil-guard tray

flat steel retainer ring for shaft

rear brake

Parts that cannot be reused after being used

SA-80 Suspension System and Automobile Axle (rear)
Rear Half Axle Shaft

Dismantle of Rear half Axle Shaft

1. Tear down the wheels.
2. Tear down the rear brake drum.
3. Tear down the grab end of the bracing wire of hand brake
from the rear brake.
4. Tear down the half-shaft and the rear brake assembly
from the rear axle housing.

5. Tear down the flat steel retainer ring for shaft from the
half-shaft;
Tear down the flat steel retainer ring for shaft with the ring
calipers.

6. Tear down the half-shaft:

Put down a wooden plate on the flat ground, and thrust the end
of spline of half-shaft and rear brake assembly toward the
wooden plate to separate the shaft and the rear brake assembly.

Inspection on and repairing of half-shaft parts

1. Check the wear, damage and swing difference half-shaft
and the flange.
Max shaft run-out: 2 mm
Max flange run-out: 0.2 mm
In case the half-shaft is damaged, or wearied or the measuring
value of the swing difference is excessive, change the half-
shaft.

2. Check he oil seal of rear wheel bearing:

Check to see whether there is wear or damage, and change the
oil seal if necessary.

3. The disassembly of the outer oil seal of rear wheel

bearing;
Tear down the outer oil seal of rear wheel bearing with SST.
Suspension System and Automobile Axle (rear)
Rear half Axle Shaft SA-81

4. Check the grooved ball bearing

Check the grooved bearing to see whether there is damage or
wear.
5. Change the bearing where necessary:
(a) Press out the grooved ball bearing with SST.

(b) Press in the new grooved ball bearing with SST.

6. Mount the new oil seal of rear wheel bearing.

Press in the new oil seal of rear wheel bearing with SST
Coat moderate lithium base grease on the lip open of oil seal.

7. Check the bearing seat.

Check the wear or damage situation.
8. Change the bearing seat where necessary:
(a) Tear down the oil seal of rear wheel bearing and the
grooved ball bearing with SST.
(b) Tap the bolts with copper bar to tear down the bearing seat.
(c) Mount the new grooved ball bearing and the oil seal of
rear wheel bearing on the bearing seat
(d) Press the rear brake, which is put on with bolts, in the
bearing seat.
9. Check the wear or damage of the inner oil seal of the rear
wheel bearing.
10. Change the rear wheel bearing where necessary:
(a) Tear down the oil seal of rear wheel bearing with SST.
SA-82 Suspension System and Automobile Axle (rear)
Rear Half Axle Shaft

11. Mount the new inner oil seal of rear wheel bearing.
Coat the hyperbolic gear oil on the axle housing where matches
with the oil seal; and plaster the moderate lithium base grease
on the lip open of the oil seal, then put them on the pressure
head and press them in.

Mount of Rear Axle Shaft

1. Press the rear brake and the bearing seat assembly on
the haft shaft.
2. Press the heated inner oil seal seat of rear wheel bearing
on he half shaft;
Notice: the face at the chamfering end of inner oil seal of
rear bearing should contact the oil seal closely, do not
mount it at the incorrect position.
Requirement for heat mount: heat the inner oil seal seat into the
22# oil (GB443-1989) to 100
, after the part is heated
completely, take it out for mount.
3. Mount on the flat steel retaining ring with the ring calipers.

4. Encase the half-shaft rear brake in the axle housing,

screw on the self-locking nut.
Tightening moment
(63-79)N
m
Notice: protect the oil seal lip open, bracing wire assembly
and the oil-guard sleeve.
5. Mount on the hand brake wire and the brake pipe.
6. Mount on the liner and rear brake drum;
7. Make a trial gas exhaust on the braking system, and
8. Mount on the rear wheels.
 Suspension System and Automobile Axle (Rear)
Rear Speed Reducer SA-83

Rear speed reducer

Element figure

80-110

column bolt
double-eared stop washer
18-26

bearing7306E

washer

stop gasket
oil-guard tray

oil seal
flange and dust
cover assembly

speed reducer housing and

differential bearing cover

adjusting ring
bearing 200719E

flat washer

differential housing

=lock plate

adjusting washer

adjusting washer
axle driven
jacket bevel gear
driving bevel gear 65-95

Bearing 7607E

N
M :specified torque

Parts that cannot be reused after being used
SA-84 Suspension System and Automobile Axle (Rear)
Rear Speed Reducer

On-vehicle Change of main-teeth oil seal

1. Disconnect the drive shaft from the speed reducer:
(a) Mark the assembly mark on the two flanges;
(b) Tear down the four sets of bolt and nut.

2. Tear down the flange and dust cover assembly.

3. Tear down the oil seal.

Tear down the oil seal with SST.

4. Mount on the new oil seal:

(a) Coat the lithium base grease on the lips of oil seal;
(b) Tap in the new oil seal with SST.
Remark: tap the new oil seal until it is in place.

5. Mount the flange and dust cover assembly.

6. Screw up the nut to the specified torque.
Specified torque: (140-160)N
m
7. Rivet the nut.

8. Connect the drive shaft flange with the speed reducer

flange:
Align the assembly mark and connect the flanges with bolts.
Tightening moment
(69-79)N
m

9. Check the oil level of the speed reducer.

Change the gear oil where necessary.
Oil brand: heavy-duty oil of grade
GL-5
Oil volume: add the oil until it overflows from the oil filler
outlet.
Viscosity: SAE 85W/90
Suspension System and Automobile Axle (Rear)
(Dismantle of Rear Speed Reducer) SA-85

Dismantle of Rear Speed Reducer

1. Take out the oil drain plug to drain the oil in the speed
reducer up.

2. Tear down the rear axle shaft.

3. Disconnect the drive shaft from the speed reducer.

4. Tear down the nuts on the bolts that connect the rear axle
housing and the speed reducer.
5. Tear down the rear speed reducer.

Disassembly of Rear Speed Reducer

Remark: in case the noise is over loud, the following item
should be checked before taking apart it to find out the causes.
If the speed reducer has serious drawback, take it apart for
repairing where necessary.

1. Check the play between the axle driven bevel gear;

In case the play value fails to be within the specified range,
adjust the preload of bearing 200719E or repair it where
necessary.
(see page SA-91)
Standard play: (0.13-0.25)mm
2. Check the teeth engagement of the driving bevel gear
with the axle driven bevel gear.
(See Page SA-92)
Record the teeth engagement positions.
3. Check the clearance between the half-shaft gear thrust
gasket and the differential housing.
Check the clearance between the half-shaft gear thrust gasket
and the differential housing with the feeler.
Standard clearance
(0.45-0.75)mm
Remark: in case the clearance value fails to fall within the
above range, change the half-shaft gear stop gasket, and
ensure the half-shaft gear stop gaskets on the left and right
sides are same in thickness.
(See Page SA-95)
SA-86 Suspension System and Automobile Axle (Rear)
(Dismantle of Rear Speed Reducer)

4. Tear down the differential and the axle driven bevel gear:
(a) Mark the assembly marks on the differential bearing
cover and the speed reducer housing.
(b) Tear down the stop gasket and take down the adjusting
ring.
(c) Loosen the double-stop washer and screw off the nut to
take down the differential bearing cover.
(d) Tear down the differential and axle driven bevel gear
from the rear speed reducer.
(e) Tear down the outer race of bearing 200719E.

Remark: mark the label on the parts to clarify the position for
re-assembling

left right

5. Tear down the flange and dust cover assembly:

(a) Loosen the riveted part of the nut with hammer and
chisel;

(b) Lock the flange with SST to tear down the nuts.
Notice: those nuts should not be reuse.

(c) Tear down the flange and dust cover assembly with
copper bar.
Suspension System and Automobile Axle (Rear)
(Dismantle of Rear Speed Reducer) SA-87

6. Tear down the oil seal and oil-guard tray:

(a) Support the face at the teeth end of the driving bevel gear
to tear down the oil seal with SST.
(b) Take out the oil-guard tray.

7. Tear down the inner race and roller assembly of bearing

7306E;
Tear down the inner race and roller assembly of bearing 7306E
with SST.

8. Tear down the driving bevel gear;

Tear down the driving bevel gear, which is mounted with
adjusting washer and inner race of bearing 7306E, together
with another adjusting washer and jacket

9. Change the bearing 7306E:

(a) Press out the bearing from the driving bevel gear with
pressure machine and SST.

(b) Mount the new inner race and roller assembly of bearing
7306E on he driving bevel gear with pressure machine
and SST.
SA-88 Suspension System and Automobile Axle (Rear)
(Dismantle of Rear Speed Reducer)

10. Change for the bearing 7306E and the outer race of
bearing 7607E:
(a) Tap out the bearing outer race with hammer and copper
bar.
(b) Press in the new bearing outer race with pressure ma-
chine and SST.

11. Tear down the inner race and roller assembly of bearing
200719E from differential.
Pull out the inner race and roller assembly of bearing 200719E
from the differential housing with SST.

12. Tear down the axle driven bevel gear.

(a) Tear down the lock plate and bolts on the axle driven
bevel gear.
(b) Mark the assembly marks on the axle driven bevel gear
and the differential housing.
(c) Tap down the axle driven bevel gear with rubber hammer
and copper bar.
Suspension System and Automobile Axle (Rear)
(Dismantle of Rear Speed Reducer) SA-89

Assembly of Rear Speed Reducer

1. Mount the inner race and roller assembly of bearing
7306E, oil-guard tray and oil seal.
(a) Put the inner race and roller assembly of bearing 7306E in
the speed reducer housing, and put the oil-guard tray on it.
(b) Coat the lithium base grease on the position of speed
reducer where oil seal locates and on the lips of oil seal,
align the oil seal and press it to mount.

2. Mount the flange and dust cover assembly

Encase the flange and dust cover assembly in the speed reducer
housing, then flat it by hand.

3. Mount the driving bevel gear:

(a) Put the adjusting washer, jacket on the driving bevel gear,
which is mounted with adjusting washer and inner race
and roller assembly of bearing 7607E, then encase the
driving bevel gear in the speed reducer housing.

(b) Screw up the nuts to tighten the flange, flat washer and
the driving bevel gear with SST, and the thread locking
agent is required to be coated when screwing.
Tightening moment
(140
160)N
m

4. Measure the pre-tightening torque of the bearing:

New bearing
(1.2-1.7)N
m
The reused bearing
(0.9-1.3)N
m
Remark: if the requirement is not satisfied, change the adjust-
ing washer under jacket until the requirement is satisfied.
(a) If the measure value is smaller than the standard one,
reduce the thickness of adjusting washer;
(b) If the measure value is larger than the standard one,
increase the thickness of adjusting washer.
SA-90 Suspension System and Automobile Axle (Rear)
(Dismantle of Rear Speed Reducer)

5. Mount the axle driven bevel gear on the differential housing:

(a) Mount on the lock plate and screw up the bolts to the
specified torque.
Tightening moment
(65-95)N
m
Notice: screw up the bolts diagonally.

(b) Tighten the lock plate with hand hammer and flat head
pinch.

6. Mount the inner race and roller assembly of bearing

200719E;
Mount the bearing inner race and roller assembly in differen-
tial housing with the pressure machine and SST.

7. Mount the differential assembly;

Mount the differential in the speed reducer housing.
When mounting the differential that hasnít changed the inner
race and roller assembly of bearing 200719E, ensure the outer
race of the left and the right bearings that has disassembled
should match with their inner racers respectively.

8. Mount the adjusting ring;

Adjust the clearance between the driving bevel gear and the
axle driven bevel gear to the moderate size. And press the
bearing outer race to flatten it with adjusting ring, and then
screw up moderately.
Notice: the two adjusting rings should be adjusted
synchronically in the movement of same direction.
Suspension System and Automobile Axle (Rear)
(Dismantle of Rear Speed Reducer) SA-91

9. Mount on the differential bearing cover:

(a) Align the assembly marks on differential bearing cover
and the speed reducer housing, and press down the
differential bearing by hand.
(b) Mount on the double-eared stop washer and the hex nut.

10. Adjust the clearance between the driving bevel gear and
the axle driven bevel gear
(a) Screw up the hex nuts connecting the differential bearing
cover to the specified torque.
Tightening moment
(80-110)N
m

(b) Attach the measuring meter seat on the face of speed

reducer housing with the measuring head touching the
teeth face, run the axle driven bevel gear with hand to
measure the teeth engagement clearance, and then com-
pare it with the clearance value in step (d) to decide the
order of the adjusting ring tightening according to the
values.

(c) Adjust and screw up the adjusting rings with SST.

Tightening moment
(115-135)N
m

(d) Check the engagement clearance again until the clear-

ance value of the three spots evenly locates on the
circumference of axle driven bevel gear. Otherwise,
adjusting ring adjustment is suggested.
Engagement clearance
(0.13-0.25)mm
SA-92 Suspension System and Automobile Axle (Rear)
Rear Speed Reducer (Disassembly of Speed Reducer)

11. Check the engagement situation of the axle driven bevel

gear and the driving bevel gear:
(a) Coat four teeth locating on different spots of axle driven
bevel gear with red powder.
(b) Rotate the axle driven bevel gear in different directions.

(c) Check the teeth engagement situation.

The teeth trace of axle driven bevel gear should satisfy
this requirement. If not, select the suitable adjusting
washer to correct according to the poor teeth engagement
situation.
Washer thickness (unit: mm) see the following table:

teeth convex =teeth concave

heel end engagement tooth top engagement

select the adjusting washer that make the main teeth

contact the axle driven bevel gear more closer.

toe end engagement

teeth root engagement

select the adjusting washers that make the main teeth apart from the axle driven bevel gear.

Group NO. Washer thickness Group NO. Washer thickness

1 1.60 7 1.90
2 1.65 8 1.95
3 1.70 9 2.00
4 1.75 10 2.05
5 1.80 11 2.10
6 1.85 12 2.15
Suspension System and Automobile Axle (Rear)
Rear Speed Reducer (Disassembly of Speed Reducer) SA-93

12. Lock the double-eared stop washer to mount the stop

gasket and bolts:
(a) If the engagement trace satisfies the requirement, lock
tightly the double-eared stop washer with hand hammer
and pinch.
(b) Mount on the stop gasket, spring gasket and bolts, and
then screw up the bolts.
Tightening moment
(18-26)N
m
(c) Tap in he adjusting ring with the pinch and hammer.

13. Measure the total preload:

Preload: (1.8-2.4) N
m
If the preload is beyond the specified range, change the gas-
kets between the jacket and bearing 7607E, until they meet
the requirement.
(a) If the preload is larger than the specified value, change
the adjusting washer.
(b) If the preload is smaller than the specified value, screw up
the nuts again slowly but not exceed 160N.m.
Notice: if the screwing torque exceeds the max torque,
change the adjusting washer and repeat the preload
process. Do not screw back the main-tooth nut to reduce
the preload.
14. Check and adjust the flange bouncing
(a) Attach the dial indicating lamp seat on the speed reducer
housing with the measuring head contact the flange face,
run the flange to observe the swing out range of the dial
indicating lamp hand.
Radial full bouncing tolerance
0.10mm

30mm Remark: the two bouncing values should be controlled within

0.10 mm, as for the parts of bounce exceeding the tolerance,
loosen the nut-driving bevel gear to assembly them in another
angle, measure the bounce value again. Observe carefully the
swing direction of the hands, which can be referred when
changing the locations of flange and the driving bevel gear. If
the requirement cannot be satisfied after several trials, change
the new flanges until the requirement is met.
15. Rivet the driving bevel gear nuts.s
SA-94 Suspension System and Automobile and Axle (Rear)
Rear speed reducer (Mount of Rear Speed Reducer and Differential Assembly)

Mount of Rear Speed Reducer and

Differential Assembly
1. Mount the speed reducer and differential assembly on
the rear axle housing.
Tightening moment
(18-26)N
m
Remark: in case the sealing gasket is mounted, it should be
checked to see whether it is damaged before mounting, if
damaged, change with the new sealing gasket, and the dam-
aged sealing gasket should be clear away; if no sealing gasket
is mounted, no mount is required to mount. Clean the contact
face of the mounted axle housing and coat it with silicon-
rubber plain sealing agent.

2. Connect the drive shaft and flange well and be careful to

align the assembly marks marked when disassembling.
Tightening moment
(69-79)N
m
Screw up the oil drain plug with the Tightening moment
of (140-150)N
m
Mount on the half-shaft and the brake assembly to adjust the
brake oil path so that the wheel brake pump is filled with brake
liquid.

3. Inject in the heavy-duty oil.

Oil brand: heavy-duty oil graded GL-5;
Viscosity: SAE 85W/90
Oil volume: add the oil until it overflows from the oil filler
outlets.
Screw up the oil-filling plug.
Tightening moment
(140-150)N
m
 Suspension System and Automobile Axle (Rear)
Rear differential SA-95

Rear Differential
Element Figure
planetary gear

differential housing half axle gear

thrust gasket

planetary gear half-axle gear

pin stop gasket
planetary
gear shaft

1. Tear down the speed reducer and the differential

assembly.

2. Tear down the differential from the speed reducer and

differential assembly.

Change of Differential Parts

1. Disassembly of Differential
(a) Tap out the pin with hammer and pinch.

(b) Tear down the planetary gear shaft, the planetary gear,
planetary gear stop gasket, half-shaft gear and half axle
gear thrust gasket.
SA-96 Suspension System and Automobile Axle (Rear)
Rear differential

2. Assembly of Differential
(a) Put the half-axle gear thrust gasket on the half-axle gear
and then encase them in the differential housing.

(b) Encase the planetary gear stop gasket, planetary gear and
encase the planetary gear shaft.

(c) Check the clearance between the half-axle gear thrust

gasket and the differential housing.
Remark: the half-axle gear and the planetary gear should run
freely without stagnant, push the planetary gear inside, then
measure the clearance between the half-axle gear thrust gasket
and the differential housing with dial indicating lamp.
Reasonable clearance range: (0.45-0.75)mm.
Remark: if the clearance value fails to fall within the above
range, change the half axle gear thrust gasket, at the same time,
ensure the left and right half axle gear thrust gasket are same
in thickness.
(d) Tap the pin in the pinhole, and rivet the end of the pinhole
so as to prevent from the pin missing.

Mount of Differential
1. Encase the differential assembly in the speed reducer
housing.
2. Mount the speed reducer and differential.
 Suspension System and Vehicle Axle
Rear Suspension (Leaf Spring Type) SA-97

Rear suspension(leaf spring)

Leaf spring and shock absorber

u-shaped bolt

spring seat

110
10

90
10 liner

90
10

rear ear pin

liner
rront ear pin

N
m
specified torque

Dismantle of leaf spring and vibration

damper
1. Raise the vehicle body with a jack and support it with a
bracket;
(a) Raise the vehicle body with a jack and support it with a
bracket;
(b) Lower the axle housing until the leaf spring is loosened
to the degree there is no tension existing. Keep the leaf
spring in such status.
2. Tear down the vibration damper.
SA-98 Suspension System and Vehicle Axle
Rear Suspension (Leaf Spring Type)

3. Tear down the U-shaped bolt;

(a) Tear down the mounting nuts of U-shaped bolts.
(b) Tear down the spring seat;
(c) Tear down the U-shaped bolts.

4. Tear down the leaf spring;

(a) Tear down the mounting nuts of front ear pin;
(b) Tear down the front ear pin;
(c) Disconnect the leaf spring from the bracket;
(d) Tear down the rear ear pin and the leaf, and then take
apart the leaf spring.

Change of leaf spring

1. Loosen the spring clip;
Loosen the spring clip with a chisel.

2. Tear down the central bolt;

Clamp the spring with a table vice at the position near to the
central bolt to take apart the central bolt.

3. Change the spring clip if necessary;

(a) Cut the rivet-head with a drill-head and tap the rivet out.
(b) Tap a new rivet in the hole of leaf spring and spring clip
and rivet it with pressure machine.
Suspension System and Vehicle Axle
Rear Suspension (Leaf Spring Type) SA-99

4. Mount the central bolt of leaf spring;

(a) Align the bolt with the spring hole after clamping the
steel spring with a table vice.
(b) Mount on and tighten the spring central bolt.
Tighten torque:
(50
5)N
m

5. Bend the spring clip to a correct angle.

Bend the spring clip to the correct position with a hammer.

Mount of leaf spring

1. Mount the steel spring;
(a) Encase the front end of leaf spring into the front bracket;
(b) Mount on the bolt of front ear pin.
(c) Screw on the nut of front ear pin with fingers;

(d) Encase the rear end of leaf spring into the rear bracket and
mount on the rear ear pin.
(e) Mount on the leaf and tighten the nuts with fingers.

2. Mount the U-shaped bolt;

(a) Mount the U-shaped bolt on the axle housing.
(b) Mount the spring seat and nut under the steel spring.
(c) Tighten the mounting nut of U-shaped bolt.
Tightening moment: (110
0)N
m
SA-100 Suspension System and Vehicle Axle
Rear Suspension (Leaf Spring Type)

Remark: Tightening U-shaped bolt to the degree that the

protruding lengths of all U-shaped bolts under the spring seat
are the same.

all lengths of bolts protruding are same

3. Mount the rear vibration damper

(a) Connect the vibration damper to the vehicle frame with
bolts and then tighten the bolts.
Tightening moment: (25
)N
m
(b) Connect the vibration damper to the sprint seat with bolts
and tighten these bolts.
Tightening moment: (25
)N
m

4. Keep the suspension frame in stable status;

(a) Mount on the wheel;
(b) Remove the bracket, and make the vehicle bounce verti-
cally for several times so as conduce it in stable status.

5. Tighten the front ear pin and rear ear pin;

Tighten the nuts of front ear pin;
Tightening moment: (90
0)N
m
Tighten the nuts of rear ear pin;
Tightening moment: (90
0)N
m
 BR-1

Braking System
Page

Notice .......................................................................... BR-2

Troubleshooting .......................................................... BR-2
Inspection and Adjustment .......................................... BR-5
Master Cylinder ........................................................... BR-8
Vacuum Booster .......................................................... BR-10
Front Brake ................................................................. BR-13
Dr .......................................................................... BR-13
SF .......................................................................... BR-20
Rear Brake .................................................................. BR-26
Dr .......................................................................... BR-26
SF .......................................................................... BR-34
Load sensing proportion valve .................................... BR-42
BR
BR-2 Braking System
Notice and Troubleshooting

Notice:
1. Carefully change each part where necessary because any
mistake will affect the brake system properties, and will lead
accidents during driving. And the parts to be changed must
be the same in part number or equal in quality.
2. Keep the parts and each position clean when repairing the
braking system.

Troubleshooting
Trouble Causes Inspection items

Lower or soft pedal Abrasion of brake shoe Change the brake shoe; Change the brake
Abrasion of brake pad pad;
Oil leakage of braking system Repair the oil leakage;
Master cylinder failure Change the master cylinder;
Air in braking system Drain out the air from braking system;
Wheel-brake cylinder failure Change the wheel-brake cylinder;
Failure in the automatic regulator of rear brake. Repair or change the regulator

Brake stagnant Poor adjustment of parking brake; Adjust the parking brake;
The bracing wire of parking brake is seized; Make repairing according to real situation;
Poor adjustment of vacuum booster pushrod) Adjust the drag rod;
Failure of the drag spring or the return spring Change the drag spring or the return spring
Pipe line blockage Make repairing according to real situation;
Brake shoe breakage or deformation Change the brake shoe
Brake pad breakage or deformation Change the brake pad
Seizing of the wheel-brake cylinder or the brake Make repairing according to real situation;
caliper piston
Automatic regulator breakage Change the regulator
Master cylinder failure Change the master cylinder

Over large braking Unsuitable tire inflation Inflate the air to suitable pressure;
distance There is oil stain or lubricant on the brake shoe or Change the brake shoe or the brake pad;
brake pad;
Brake shoe deforms, the brake liner is worn or polished; Change the brake shoe;
Brake pad deforms or is worn or polished; Change brake pad
Brake drum or brake disc deforms Change the brake drum or the brake disc;
Drag spring or return spring has trouble Change the spring;
The wheel-brake cylinder has trouble Change the wheel-brake cylinder;
The inner piston of wheel-brake cylinder is seized; Change the wheel-brake cylinder
The brake pad is seized; Change the brake pad

The brake pedal is hard There is oil stain or lubricant on the brake shoe or Change the brake shoe brake pad;
but doesn
t work; brake pad;
The brake shoe deforms, brake liner is worn or Change the brake shoe
polished, or the brake wheel is worn;
The brake pad deforms, or is worn or polished; Change the brake pad;
The piston of wheel brake pump is seized; Change the wheel-brake cylinder;
The vacuum booster has trouble Change the vacuum booster;
The vacuum degree is unsuitable Make repairing according to real situation;
The brake pipe line is blocked Make repairing according to real situation;
 Braking System
Notice and Troubleshooting BR-3

Troubleshooting (continued)
Trouble Causes Inspection items
There is clatter noise when using (Drum-type brake) Add lubricant
the brake The brake shoe is seized on the flange of rear baffle; Change the lubricating flange
The flange of rear baffle is worn; Change
The pressure spring of brake shoe is loose or missing; Tightening it
The fixed bolts of brake bottom plate is loose;
(disc type brake) Change
The brake pad support plate is loose or missing Tightening it
The mounting bolts are loose;

There is hoarse noise or quack- The brake shoe or brake pad is worn; Change the part, and re-process
quack when using the brake precisely the brake drum or
rotator if the abrasion is serious;
The brake caliper, the wheel or the rotator interferes each Make change according to real
other. situation;
repair or change
There is friction between the dust cover and brake disc, Make repairing according to
the brake bottom plate and the brake drum; real situation;
The other braking part has trouble Change
There is friction between the tire and body Check or maintain the part

There is such noise as The brake drum, brake liner, liner or brake pad is worn Check, repair or change
continuous screaming, quack- or scraped
quack, oscillating sound, etc. The brake liner or brake pad is dirty or with oil stain or Clean or change
Notice: the braking materials polished.
may generate the natural noise The brake liner or brake pad is improperly used. Check or change
and heat during friction, and The brake pedal or vacuum booster drag rod is unsuitably Check for adjustment
thus emit the energy. Therefore, adjusted.
it is normal to have the (disc type brake)
screaming noise. These The brake pad silent pad is loss or damaged; Change
phenomena will be more serious The brake pad is worn to the degree that the abrasion- Change
under the condition of frigidity, indicating lamp of brake pad has friction with the rotator.
torridity, and over humidity, There is burr or rust on the brake caliper. Clean or polish the burr
snowing and mud. the (Drum type brake)
screaming noise occurring The pressure spring of brake shoe is soft in rigidity, or is Check, repair or change
occasionally will not lead the damaged or unsuitable.
fatal brake trouble nor reduce The pressure spring pin or spring of brake shoe is loose Check, repair or change
the effective properties of the or damaged;
brake. There is crack on the brake bottom plate flange Check, repair or change
BR-4 Braking System
Notice and Troubleshooting

Troubleshooting (continued)
Trouble Causes Inspection items
There are quack- Alien materials such as stone is reeled inside the wheel shell Clear away the alien materials
q u a c k n o i s e s Nuts on hub is loose; Tighten the nut to the specified torque; and
without using the change it in case the bolt hole is enlarged;
brake. The brake pedal or vacuum booster pushrod is adjusted Check and adjust
improperly;
The wheel bearing is worn or damaged or lubricated Check, lubricate or change
insufficiently;
(disc type brake)
The outer end edge of brake pad support plate or brake pad Check repair or change
is dog-eared;
The silent pad is poor in properties; Check and make change according to real
situation
The sliding liner is worn; Check and make change according to real
situation
The mounting bolt is loose Check and tighten according to the necessity.
The piston returns incompletely Check, repair or change
(drum type brake)
There is loose or redundant part. Check, take out or repair.
There is continuous The brake pedal or vacuum booster pushrod is adjusted Check and adjust
screaming noise improperly
without using brake The vacuum booster, master cylinder or wheel-brake cylinder Check, repair or change
returns incompletely.
(Disc type brake)
The piston is rusted or seized; Check and add the lubricant according to
the necessity;
The brake pad in brake caliper locates improperly; Repair or change
There is friction between the brake disc and brake caliper Repair or change
shell;
The brake pad support plate is mounted improperly; Repair or change
There is interference between the abrasion indicating lamp Change
of brake pad and the brake disc due to the brake pad
abrasion;
(Drum type brake)
The pressure spring of brake shoe is soft rigidity, damaged Change
or unsuitable;
There is crack on the brake bottom plate flange; Repair or change
There is interference of brake bottom plate with the brake Repair or change
drum after it is bending or warping.
The brake drum interferes with the brake bottom plate or Change the brake drum
with brake shoe due to it is processed improperly;
Other brake parts
Check, maintain and change according to
the necessity;
There is loose or redundant part in braking system;
The brake liner is polished due to it is adjusted over-tightly; Check, maintain and change according to
the necessity;
The wheel bearing is worn, damaged or lubricated Check, maintain and change according to
insufficiently. the necessity;
 Braking System
Inspection and Adjustment BR-5

braking lamp switch Inspection and adjustment

pedal push rod Inspection on and adjustment of brake pedal
1. Check the pedal height as shown in the drawing to
whether it is correct,
The height from the pedal to the front floor:
Dr SF
160mm
SL SK SY SJ
(190-200)mm

2. Adjust the pedal height if necessary:

(a) Loosen the locking nuts of braking lamp switch;
(b) Loosen the braking lamp switch to the most degree.
(c) Loosen the locking nuts of drag rod;
(d) Adjust the pedal height through rotating the pedal drag
rod;
pedal height (e) Rotate the stop light switch reversibly until it contact
with the stop baffle of pedal.
(f) Screw up the two locking nuts.
(g) Check the braking lamp is lightened or not when tread
down the brake pedal.
(h) Check and adjust the pedal free stroke after adjusting the
pedal height

3. Inspection on Pedal Free Stroke:

pedal push-rod (a) Stop the engine working and tread down the brake pedal
several times until the vacuum booster is not in the stage
of vacuum.
(b) Tread down the pedal until the resistance occurs, and
measure the distance shown in the drawing.
Pedal free stroke
(3-6)mm

QK Adjust the free stroke of pedal if necessary:

(a) Loosen the locking nuts of the pedal drag rod and rotate
the pedal drag rod to adjust the pedal free stroke.
(b) Start the engine to confirm the free stroke.
(c) Check the pedal height after adjusting the pedal free
stroke.

free stroke of
pedal: (3-6) mm
BR-6 Braking System
Inspection and Adjustment

Operation test of vacuum booster

Remark: check the operation of vacuum booster with the
vacuum booster tester if workable.
1.Operation inspection
(a) Before starting the engine, tread down the brake pedal
several times, and check the pedal reservation distance to
ensure there is no change occurs.
(b) Tread down the brake pedal and start the engine. If the
treaded pedals continue to move downward, which means
the operation is normal.
1. Inspection on Air-tight
normal abnormal
(a) Start the engine for 1-2 min and then turn it off. Then
tread down the brake pedal slowly for several times, if the
pedal move downward continuously in the first, but
return gradually in the second or third time, which means
the third time
the vacuum booster has a good air-tight.
the second time (b) Tread down the brake pedal when the engine is working,
the first time then stop the engine, but tread the pedal down. If the
reservation distance doesnít change within the 30 seconds,
which shows the air tight of vacuum booster is good.

Air-bleeding of braking system

Remark: air-bleeding is required if any operation for braking
system is conducted or the pipe line is doubted to have air.
1. Fill the oil cup with the brake liquid
Check the liquid level of oil cup after the air in each wheel
brake pump is exhausted. If necessary, add the brake liquid.
2. Connect the vinyl resin pipe with the vent screws.
Insert the other end of pipe into the container with half brake
liquid.
Remark: the air-bleeding shall begin from the longest pipe line
when the wheel-brake cylinder is exhausting the air.

3. Air exhaust of the pipe line in braking system

(a) Tread down brake pedal slowly several times.
(b) Loosen the vent screws until the brake liquid flows out
while letting the assistant tread down the pedal. Then
screw up the vent screws.
(c) Repeat this approach until there is no air in the liquid.
4. Repeat the approach for the wheel-brake cylinder.
Braking System
Inspection and Adjustment BR-7

Check and adjust the parking brake

1. Check the stroke of operating lever of the parking
brake to see whether it is correct.
Drag the brake operating lever to the max stroke and count the
grooves it passes.
Stroke of operating lever of parking brake:
Dr
(9-10) Teeth
SL SK SY
(7-9) Teeth

2. Adjust the parking brake lever where necessary:

Remark: Adjust the rear brake shoe clearance before the
adjustment.
Brake shoe clearance: 0.6mm
(a) Loosen the locking nut and then rotate the adjustable nut
until the stroke is correct, then screw up the nuts.
(b) The brake shoe shall not be stagnant after the adjustment.
BR-8 Braking System
Master Cylinder

Master Cylinder
Disassembly of Master Cylinder

cup cap

filtering screen

oil cup

vacuum booster assembly

sealing liner

front three-way valve

master cylinder body

1. Tear down the alarm joint for liquid level;

2. Exhaust the brake liquid with the injector:

Notice: brake liquid must not be left on the paint surface,
if any, clear it away.

3. Tear down the pipeline of braking system;

SST
Tear down the pipeline of braking system from the master
cylinder with SST.

4. Take apart the master cylinder:

(a) Tear down the four nuts and the three-way joint.
(b) Tear down the master cylinder and sealing washer from
the vacuum booster

SST
 Braking System
Master Cylinder BR-9

Mount of Master Cylinder

1. Adjust the length of vacuum booster pushrod before
mounting the master cylinder;

2. Mount the master cylinder:

Mount the master and sealing washer on the vacuum booster
with four nuts.

SST

3. Connect the two pipelines of braking system;

Mount the brake pipeline on the master cylinder with SST and
screw up the nuts.
Fastening torque

Dr SF
(18
2)N
m
SL SK SY SJ
(19
1)N
m

SST

4. Connect the alarm switch joint for liquid level;

5. Fill the oil cup with brake liquid and exhaust the air in
the brake pipeline;

6. Check to see whether there is brake liquid leakage;

7. Check and adjust the brake pedal.

BR-10 Brake System
Vacuum Booster

Vacuum booster
Disassembly of Vacuum Booster

U-shaped clip head

bracket

shock pad

one-way valve adjusting shim

shock pad

sealing liner
vacuum booster

master cylinder body

front three-way valve

Disassembly of Vacuum Booster

1. Take apart the master cylinder

2. Tear down the vacuum hose from the vacuum booster

3. Tear down the return spring

4. Tear down the clamping pin and U-shaped clamping pin

5. Tear down the vacuum booster, sealing washer and U-

shaped clamping head
 Brake System
Vacuum Booster BR-11

air Inspection on Vacuum booster parts

Operation for one-way valve inspection
(Gasoline engine)
(a) Tear down the one-way valve;
engine side booster side (b) Check the air to see whether it flows from the vacuum
booster side toward the engine side.
(c) Check the air, change the one-way valve if the air flows
air airless from the side of engine toward the vacuum booster.
(d) Mount the one-way valve in the right place.

air (Diesel engine)

(a) Tear down the one-way valve from the vacuum pipe.
(b) Check the air to see whether it flows from the side of
hose side vacuum side vacuum room to the hose.
(c) Check the air, and change the one-way valve if the air
flows to the hose to the vacuum room.

air airless

Mount of Vacuum Booster

1. Adjust the length of vacuum booster pushrod:
SST
(a) Mount the sealing washer on the master cylinder;
(b) Put SST on the sealing washer and descend the pin rod
until it contact lightly the piston with its top;
washer

SST (c) Put top of SST downward ,and mount it on the vacuum
booster.
(d) Check the clearance between the vacuum booster pushrod
and the head of pin on SST.
(e) Adjust the length of vacuum booster pushrod until the
pushrod touches the pinhead.

2. Mount the vacuum booster, sealing washer and Ushaped

clip head.
(a) Mount the vacuum booster and sealing washer.
(b) Mount the U-shaped clip head.
(c) Mount and tighten the assembling nuts of vacuum booster.
3. Connect the U-shaped clip head and the brake pedal:
Encase the U-shaped clamping pin in the hole of U-shaped clip
head and the brake pedal, and then mount the spring pin on the
U-shaped clamping pin.
BR-12 Brake System
Vacuum Booster

4. Mount the pedal return spring.

5. Mount the brake master cylinder

(see Page BR-8)

6. Connect the hose and the vacuum booster.

7. Fill the oil cup with brake liquid and exhaust the air in
braking system.
(see page BR-6)

8. Check the liquid leakage;

9. Check and adjust the brake pedal

(See page BR-5)

10. Check the operation

(See Page BR-6)
 Braking System
Front Brake (Dr) BR-13

Front Brake
Element figure

Dr

No. 1 lock plate of brake pad

No. 2 lock plate of brake pad

silent pad cluster

brake pad assembly

silent pad cluster

caliper body
No. 2 lock plate of
No. 1 lock plate of
brake pad
brake pad
sliding sleeve dust cover
long sliding caliper liner
sliding sleeve dust cover

caliper body

rectangular sealing ring

piston dust cover long sliding caliper sleeve

vent screw dust cover

vent screw

piston dust cover piston

sliding sleeve dust cover
snapping spring
sliding sleeve dust cover short sliding caliper sleeve

short sliding caliper liner

BR-14 Braking System
Front Brake (Dr)

Brake pad change

Remark: Check the thickness of the friction material of brake
pad through the observation hole on caliper body after the
vehicle covers thirty thousand; if the thickness fails to fall
within the specified range, change is required. (If the brake is
used often, the thickness of friction materials of brake
pad is required to check whether it is within the specified
range after the vehicle covers more than ten thousand,
if not, change it.
1. Tear down the front wheel;

2. Check the thickness of friction material of brake pad:

Check the thickness of friction material of brake pad through
the observation hole on caliper body, if it fails to be within the
specified range, change it.
Min thickness: 2.0mm

3. Raise the wheel-brake cylinder:

(a) Tear down the short bolts of sliding sleeve;

(b) Uplift the wheel brake pump and hang it with rope to
protect the brake oil pipe.
Remark: Do not loosen the brake oil pipe and the bleeding plug.

4. Tear down the following parts:

(a) Two braking pads;
(b) Two silent pad clusters;
(c) Four braking pad lock plates.
Braking System
Front Brake (Dr) BR-15

5. Brake disc measurement

(See page BR-17)

6. Measure the radial run-out of the brake disc;

(See BR-18)

7. Mount the lock plate of brake pad.

8. Mount the new brake pad.

(a) Mount the silent pad cluster on brake pads of both the
inner and outer sides;
Remark: Pollution of oil stain or coat is not allowed on the
work faces of brake pad or brake disc.

(b) Draw out a little brake liquid from the liquid container to
prevent the brake liquid overflowing from the liquid
container;
(c) Press in the piston with the hammer lever or similar tool.

9. Mount the wheel-brake cylinder;

Mount and screw up the hex bolts (the hex bolts shall be coated
with the thread locking sealing agents.
Fastening torque
(38-50)N
m
Remark: only one brake pad can be changed in one time so as
to prevent the piston of other wheel being shot out.
BR-16 Braking System
Front Brake (Dr)

10. Mount the front wheel;

Screw up the fixing nut of wheel.
Fastening torque
(135
150)N
m

Disassembly of Wheel-brake Cylinder

1. Take apart the brake pipeline.
(a) Tear down the brake pipeline. And block the outlet with
a clean cork.
(b) Tear down the brake oil pipe bracket from the wheel-
brake cylinder.

2. Tear down the wheel-brake cylinder from the caliper

bracket.
Tear down the two hex bolts and the wheel-brake cylinder.

3. Tear down the brake pad:

(a) Two brake pad;
(b) Two silent pad cluster;
(c) Four brake pad lock plate.

Pump Disassembly of Wheel brake

1. Take apart the following parts:
(a) Two sliding sleeve;
(b) Four sliding sleeve dust cover;
(c) Two sliding liner.
Braking System
Front Brake (Dr) BR-17

2. Tear down the piston dust cover snapping ring and the
piston dust cover;
Tear down the piston dust cover snapping ring and the piston
dust cover with screwdriver.

3. Tear down the piston from the wheel-brake cylinder:

(a) Put a wooden plate between the piston and the caliper
body.
(b) Tear down the piston from wheel-brake cylinder with the
compressed air.
Warning: Do not put your finger in front of the piston when
using the compressed air.

4. Tear down the piston sealing ring from the caliper body.
Tear down the piston sealing ring with bent needle.
Notice: the tools used shall not be sharp so as not to
scrape the piston sealing ring.

Check the front brake parts

1. Measure the thickness of brake pad liner;
Standard thickness
10.0mm
Min thickness
2.0mm
If the thickness is less than the min thickness or is unevenly
worn; change the brake pad.

2. Measure thickness of brake disc

Standard thickness
25.0mm
Min thickness
23.0mm
If the brake disc is scraped, repair it, if the brake is serious
worn to the degree that its thickness is less than the min thickness,
brake disc requires to be changed
BR-18 Braking System
Front Brake (Dr)

3. Measure the bouncing value of the brake disc face;

Remark: verify the bearing is aligned correctly before
measuring.
The bouncing value of max face: 0.11mm

4. Change the brake disc according to the requirements

(a) Tear down the calipers body from the steering knuckle.
(b) Tear down the hub and the brake disc (See Page SA-11).
(c) Mount the new brake disc and screw up the connecting
bolts according to the specified torque.
Fastening torque
(60
79)N.m
(d) Mount the hub and brake disc assembly (see page SA-12);
(e) Mount the caliper bracket on the steering knuckle and
screw up the bolts according to the specified torque.
Fastening torque
(85
105)N.m

Cylinder Assembly of Wheel-brake

1. Preparation
All parts shall be washed, dried and cleared away the alien
materials before the assembly. And coat moderate vacuum
silicon base grease on the work faces of sliding sleeve dust
cover, sliding sleeve and the sliding liner; and plaster the
moderate rubber lubricant on the work faces of piston, piston
dust cover and the rectangular sealing ring.

2. Encase the piston sealing ring and piston in the caliper body;
(a) Screw the vent screw in the vent hole of calipers.
Fastening torque
(8
13)N.m
(b) Coat moderate rubber lubricant on the work face rectan-
gular sealing ring and encase the caliper body in groove.
(c) Encase the piston in the caliper body.

3. Encase the piston dust cover and the dust cover

snapping ring in the wheel-brake cylinder.
Braking System
Front Brake (Dr) BR-19

4. Mount the sliding liner, sliding sleeve dust cover and

sliding sleeve.
(a) Encase the sliding liner and sliding sleeve dust cover in
the wheel-brake cylinder.
(b) Ensure the sliding sleeve dust cover in the ring groove of
wheel-brake cylinder hard.

(c) Encase the sliding sleeve in the sliding sleeve dust cover.
(d) Ensure the sliding sleeve dust cover in the ring groove of
sliding sleeve.

Mount of Brake Calipers

1. Mount the brake pad;

2. Mount the wheel-brake cylinder:

(a) Mount the wheel-brake cylinder;
(b) Mount and tighten the two assembling bolts (the bolts
shall be coated with the thread locking sealing agent).
Fastening torque
(38
50)N.m

3. Connect the brake pipeline.

Connect the brake pipeline with the calipers.
Fastening torque
(21
2)N.m
4. Observe the height of brake liquid level and, if
necessary, add in the brake liquid and exhaust the air
in braking system.
Notice: prevent the brake liquid from spraying on the
brake disc when exhausting air.
5. Check to see whether there is leakage of brake liquid.
BR-20 Braking System
Front Brake(SF)

Front Brake
Element figure
SF

spring gasket12
brake caliper
brake pad snapping ring

123 silent pad

separation pads
brake pad

guide pin lock spring

brake disc

guide pin

sealing ring

piston dust cover steel gripping hoop

N
M : fastening torque piston dust cover

Change of Brake pad

Remark: In case there is a continuous screaming from the front
wheel when braking the vehicle during driving, check the
alarm pad for friction limit for brake pad. If there is friction
trace on the alarm pad with the brake disc, change the brake pad

1. Disassemble the front wheel;

2. Check the thickness of friction material of brake pad.

Check the thickness of friction material of brake pad, if it fails
to be within the specified range, change the brake pad.
Min thickness
2.0mm
Braking System
Front Brake(SF) BR-21

3. Disassemble the following parts:

(a) Guide pin snapping spring;
(b) Two guide pins;
(c) Brake pad snapping ring
(d) Two brake pads;
(e) Two silent pads; and
(f) Two separation pads

4. Measure the thickness of brake disc.

(See BR-24)

5. Measure the radial swinging of the brake disc.

(see page BR-24)

6. Mount on the new brake pad;

(a) Draw out a little brake liquid from the liquid container.
(b) Press in the piston with the hammer lever and similar tool.
Remark: Only one brake pad of the same wheel can be changed
in one time so as to prevent the piston on the other face ejecting
out.

(c) Mount two silent pads and two separation pads on the
new brake pad.
Remark: coat the brake oil for disc on the inner silent
pads.
(d) Mount the brake pad with the worn limit alarm pad on the
inner side, while the other brake pad on the outer side.
Note: Pollution of oil stain or coat is not allowed on the
work faces of brake pad or brake disc.

7. Mount the brake pad snapping spring;

Brake pad snapping spring shall be mounted at the lower
position;
BR-22 Braking System
Front Brake(SF)

8. Mount the two guide pins;

9. Mount the guide pin snapping spring

Disassembly of Wheel brake Pump

1. Disassemble the front wheel;í
2. Disassemble the brake pipeline;
Tear down the brake pipeline with a container containing the
brake liquid.

3. Disassemble the wheel-brake cylinder.

Tear down the two hex bolts and the wheel-brake cylinder.

4. Disassemble the following parts:

(a) Guide pin snapping spring;
(b) Two guide pins;í
(c) Brake pad snapping spring;
(d) Two brake pads;
(e) Two silent pads and
(f) Two separation pads.
 Braking System
Front Brake(SF) BR-23

Wheel-brake cylinder disassembly:

1. Tear down the dust cover steel gripping hoop and the
dust cover.
Tear down the dust cover steel gripping hoops and piston dust
covers of the four wheel-brake cylinders with the screwdriver.

2. Tear down the piston from the wheel-brake cylinder:

(a) Prepare a wooden block with the dimensions as shown in
the drawing (which is used to support the piston)
mm

mm

mm

(b) Put the wooden block between the pistons and insert one
brake pad on one side of the wooden block.
(c) Tear down the four pistons from the wheel-brake cylin-
der by using the compressed air.
Warning: do not put your fingers in front of the piston
when using the compressed air.

3. Tear down the piston sealing ring.

Tear down the four piston sealing ring from the wheel-brake
cylinder with the screwdriver.

Check the front brake parts

1. Measure the thickness of brake pad liner;
Standard thickness
9.0mm
Min thickness
2.0mm
In case the liner is less than the min thickness or the liner is
worn unevenly, change the brake pad.
BR-24 Braking System
Front Brake(SF)

2. Measure the thickness of brake disc;

Standard thickness
20.0mm
Min thickness
18.0mm
If the brake pad is scraped, repair it; where the abrasion is
serious and its thickness is smaller than the min thickness,
change the brake disc.

3. Measure the bounding value of the brake disc face;

Remark: the bearing is required to be verified in the suitable
adjustment before measuring.
Max face bouncing value: 0.11mm;

4. Change the brake disc according to the requirement:

(a) Tear down the hub and the brake disc. (see the paragraph
of front wheel hub)
(b) Mount the new brake disc and screw up the connecting
bolts as the specified torque.
(c) Mount the hub and brake disc assembly. (see the para-
graph of front wheel hub).
Fastening torque
(75
5)N
m
(d) Mount the caliper bracket on the steering knuckle and
screw up the bolts according to the specified torque.
Fastening torque
123N
m.

Assembly of Brake-wheel pump

1. Preparation
All parts shall be washed, dried and cleared away the alien
materials, and coat moderate rubber lubricant on the work
faces of piston, piston dust cover and rectangular sealing ring.

2. Encase the piston sealing ring in the caliper body

Braking System
Front Brake(SF) BR-25

3. Encase the piston in the caliper body.

4. Encase the piston dust cover, dust cover steel-

gripping hoop in the caliper body.

Mount of Brake Calipers

1. Mount the brake caliper and screw up the two
mounting bolts.
Fastening torque
123N
m

2. Mount the brake pads;

3. Connecting the brake pipeline;

Use the open spanner to connect the pipeline.
Fastening torque
(21
1)N
m
4. Observe the height of brake liquid level and, if
necessary, add in the brake liquid and exhaust the air
in braking system.
Notice: avoid the brake liquid of spraying on the brake disc
when exhausting the air.
5. Check to see whether there is leakage of brake liquid.
BR-26 Braking System
Rear Brake (Dr)

Rear brake
Element figure
wheel-brake cylinder cluster
Dr

pressure spring drag rod

brake shoe gear
return spring

split pin
self clearance- parking brake arm
adjusting bracing
flat washer
wire

parking brake push plate

back brake
shoe push-plate spring

front brake shoe self clearance-

adjusting toggle
tension spring
pressure spring

brake drum

clearance adjuster

pressure spring seat

Parts that cannot be reused after being used

Disassembly of Rear drum-type Brake

Remark: if the braking torque of manual brake cannot satisfies
the braking requirement, it is suggested to check the thickness
of brake shoe liner, where the thickness is less than the min
thickness, change the brake shoe.
Min thickness
1.0mm

1. Tear down the rear wheel;

2. Tear down the brake drum;

Remark: in case the brake drum is not easy to tear down, the
following steps shall be adapted:
(a) Tear down the clearance-adjusting hole; insert a screw-
driver in the brake bottom plate hole to prize up the
adjusting bolt inner tilt angle with the self-adjusting fork.
(b) Use another screwdriver to adjust the adjusting bolt inner
tilt angle to loosen the clearance adjuster of brake shoe.
Braking System
Rear Brake (Dr) BR-27

3. Tear down the return springs of the two brake

shoes.

4. Tear down the self-adjusting bracing wire, brake shoe

retainer ring, bracing wire guide seat and the self-
clearance adjusting toggle plate.
(a) Press and push the self clearance-adjusting toggle plate to
teardown the bracing wire of self clearance-adjuster,
brake shoe retainer ring and bracing wire guide seat.
(b) Take out the spring from the self clearance-adjusting
toggle plate to tear down the clearance-adjusting toggle
plate and the spring.

5. Tear down the tension spring;

Tear down the tension spring with the pliers.

6. Tear down the brake shoe, clearance adjuster and

parking brake push plate.
(a) Tear down the pressure spring seat, pressure spring and
pressure spring drag rod.
(b) Tear down the brake shoe, clearance adjuster and parking
brake push plate.

(c) Tear down the bracing wire from the parking brake.
BR-28 Braking System
Rear Brake (Dr)

7. Tear down the parking brake arm;

Tear down the split pin with pliers to take apart the parking
brake arm.

8. Take apart the brake pipeline from the wheel pump;

Tear down the brake pipeline and block the oil pipe with a clean
cork.

9. Tear down the wheel brake pump;

Tear down the two bolts and the wheel-brake cylinder.

10. Tear down the following bolts and wheel-brake

cylinder parts:
(a) Two piston rod;
(b) Two dust cover
(c) Two pistons
(d) Two piston rubber bows
(e) Spring.
Braking System
Rear Brake (Dr) BR-29

Check and Repair the Rear Brake Parts

1. Check and test the disassembled parts;
Check the disassembled parts to see whether there is abrasion,
rust or damage.

2. Measure the inner diameter of brake drum;

Standard inner diameter)
254.0mm
Mix inner diameter: 256.0mm

3. Measure the thickness of brake shoe liner;

Standard thickness
5.0mm
Min thickness
1.0mm
In case the thickness of brake shoe liner is less than the min
thickness or there is uneven abrasion, change the liner.
Remark: if one of the brake shoes is needed to change, all of the
brake shoes are required to change so that the even braking
performance is maintained.

4. Measure the brake liner and the brake drum to see

whether they contact closely;
If there is poor contact between the brake liner and the brake
drum, repair the brake shoe with the grinding devices, or
change the brake shoe cluster.
BR-30 Braking System
Rear Brake (DR)

Assembly of Rear Brake

remark: assemble the parts according to the
direction in the drawing;

forward forward

left wheel right wheel

Assembly of Rear Brake

1. Assemble the wheel-brake cylinder:
(a) Coat moderate lithium soap base glycol grease on the
piston cup;
(b) Assemble the wheel-brake cylinder:


Mount the two piston cups on two piston;


Encase the spring and two pistons in the wheel cylinder
body and


Mount the two dust covers
Remark: Assembly shall be conducted correctly according to
the direction shown in the drawing.

2. Mount the wheel-brake cylinder:

(a) Use two bolts to fix the wheel-brake cylinder on the rear
bottom plate.
Coat moderate sealing glue (Glue 704) on the position where
the wheel-brake cylinder connects with the bottom plate.
Fastening torque
(16
20)N
m
(c) Connect the brake pipeline on the wheel-brake cylinder.
Fastening torque
18N
m

3. Coat the following parts with moderate lubricant that

resistant high temperature (do not pollute the friction
plates);
(a) The upper plain of the hex convex platform where the
bottom plate connects the brake shoe;
(b) Contact face of the brake shoe and the top lever of wheel
cylinder;
(c) Contact face of the brake shoe with the support pin.
Braking System
Rear Brake (DR) BR-31

(d) Adjusting bolts

(e) Contact position where the clearance adjuster and the
brake shoe.

4. Mount the parking brake drag arm;

Mount the new split pin with pliers to mount the parking brake
drag arm.

5. Mount the rear brake shoe:

(a) Mount the parking brake bracing wire on the parking
brake drag arm.
(b) Mount the rear brake shoe in such way that its end is
inserted into the cylinder rod. Encase the pressure spring
drag rod in the brake bottom plate and the brake shoe
assembly in turn and then insert it in the pressure seat ,
pressure spring, pressure spring seat, finally rotate the
pressure spring in place with the pressure spring fork.

6. Mount the parking brake pull plate and the front brake shoe:
(a) Mount the pull plate and the spring.
(b) Mount the front brake shoe, of which, the end is inserted
in the piston rod, and mount the pull plate. Insert the
pressure spring drag rod in the brake bottom plate and
brake shoe assembly in turn, then encase it in the pressure
spring seat, pressure spring and pressure spring, finally
rotate the pressure spring in place with the pressure
spring.

7. Mount the tension spring;

Mount the tension spring with pliers.
BR-32 Braking System
Rear Brake (DR)

8. Mount on the adjuster;

Poke the brake shoes with the screwdriver and then mount the
adjuster.

9. Mount the brake shoe retainer ring, bracing wire of

guide seat, self clearance-adjusting bracing wire and
the return spring.
(a) Mount the brake shoe retainer ring, then the front return
spring.
(b) Mount the return spring ,and then mount the forward
return spring.

10. Mount the self-clearance toggle plate:

(a) Mount the toggle plate bracing wire torsion spring on the
rear brake shoe.
(b) Mount the clearance self-adjusting toggle plate and hook
It with the clearance-adjusting bracing wire.
(9) Hook the self clearance-adjusting toggle plate with the
bracing wire torsion spring

11. Check the operation of self-adjusting mechanism.

(a) Drag the clearance-adjusting bracing wire backward as
shown in the drawing, then release it. Check the clear-
ance-adjusting bolts to see whether it is rotating. If not,
forward check the rear brake to verify which part has problem.

(b) Adjust the clearance adjuster to shorten its length as

possible as can.
(c) Mount the brake drum
Braking System
Rear Brake (DR) BR-33

12. Check the clearance between the brake shoe and the
brake drum:
(a) Tear down the brake drum;
(b) Measure the inner diameter of the brake drum and the
outer diameter of brake shoe to check whether the differ-
ence of the two diameters falls within the standard
clearance range.
Shoe clearance: 0.6mm
If it is not correct, check the parking brake system.

13. Mount the brake drum and the rear wheel; screw up
the nuts of rear wheel hub.
Fastening torque
(145
10)N
m

14. Fill the liquid container with brake liquid and exhaust
the air in braking system.

15. Check to see whether there is leakage of brake liquid.

BR-34 Braking System
Rear Brake (SF)

Rear brake
Element figure
SF wheel-brake cylinder cluster

observation hole cork

claming pin

clearance adjuster
rear brake shoe

brake lever

upper tension spring toggle plate

observation hole cork

open retainer ring
lower tension spring
front brake shoe
clearance-adjusting spring

pressure spring
pressure spring cap

brake drum

Parts that cannot be reused after using.

Disassembly of Rear Brake

1. Check the thickness of the brake shoe liner:
Tear down the observation hole cork I and measure the thickness
of brake shoe liner through the observation hole. If the thickness
if less than the min thickness, change the brake shoe.
Min thickness
1.0mm
2. Tear down the rear wheel.

3. Tear down the brake drum;

Remark: if the brake cannot be tear down easily, the following
steps shall be adapted:
(a) Tear down the observation hole cork II by inserting the
screwdriver in the hole of brake bottom plate, and poke
the toggle plate from the self-adjusting screw arbor.
(b) Loosen the brake shoe clearance adjuster with another
screwdriver by screwing the self-adjusting screw arbor.
Braking System
Rear Brake (SF) BR-35

4. Tear down the front brake shoe:

(a)Tear down the tension spring from the front brake shoe;

(b) Tear down the pressure spring cap of brake shoe, the
pressure spring and claming pin.
(c) Tear down the lower tension spring from the front shoe
and the shoe pads.
(d) Tear down the lower tension spring from the rear shoe.

5. Tear down the rear brake shoe:

(a) Tear down the shoe pressure spring cap, pressure spring
and claming pin.
(b) Tear down the upper tension spring from the shoe pad.

(c) Tear down the rear brake shoe and the clearance adjuster.
(d) Tear down the parking brake bracing wire from the brake
shoe.

6. Tear down the clearance adjuster from the rear brake shoe:
(a) Tear down the clearance-adjusting spring.
(b) Tear down the clearance adjuster.
BR-36 Braking System
Rear Brake (SF)

7. Tear down the toggle plate and the brake lever:

(a) Tear down the open retainer ring;
(b) Tear down the toggle plate;

(c) Tear down the pin clip;

(d) Tear down the brake lever.

8. Tear down the wheel-brake cylinder:

(a) Tear down the brake pipeline. And block the pipeline
with a clean cork.
(b) Tear down the two bolts to take apart the wheel-brake
cylinder.

9. Tear down the following parts:

(a) Two dust covers;
(b) Two pistons;
(c) Two piston cups
(d) Spring.
Braking System
Rear Brake (SF) BR-37

Check and Repair the Brake Parts

1. Check the disassembled parts;
Check the disassembled parts to see whether there is abrasion,
rust or damage.

2. Measure the inner diameter of the brake drum;

Inner diameter
295.0mm
Max diameter
297.0mm

3. Measure the thickness of brake shoe liner;

Standard thickness
6.5mm
Min thickness
1.5mm
In case the thickness of brake shoe liner is less than the min
thickness or there is uneven abrasion, change the brake shoe.
Remark: if either brake shoe is required to change, all rear
brake shoes shall be changed to maintain the even braking
properties.

4. Check the brake shoe liner and the brake drum to see
whether there is close contact;
If there is poor contact between the brake shoe liner or brake
drum, repair or change the brake shoe cluster with the grinding
devices.
BR-38 Braking System
Rear Brake (SF)

Assembly of Rear Brake

remark: assemble the component elements in the direction shown in the drawing;

forward forward

left wheel right wheel

1. Assemble the wheel-brake cylinder:

(a) Coat moderate lithium soap base glycol grease on the
piston cup.
(b) Assembly the wheel-brake cylinder


Mount the two piston cups on two pistons


Mount the two dust cover on two pistons.


Encase the spring and the two pistons in the wheel
cylinder body.
Remark: assembly correctly according to the direction shown
in the drawing.
2. Mount the wheel-brake cylinder:
(a) Mount the wheel-brake cylinder on the rear bottom plate
with two bolts.
Fastening torque
(6.5
10)N
m
(b) Connect the brake pipeline on the wheel-brake cylinder.
Fastening torque
(18+2)N
m

3. Coat the lithium base grease on the following parts:

(a) Hex convex platform where the bottom plate contacts
with the brake shoe.
(b) Two ends of support brocks
(c) Contact position where the piston and the shoe rib.
Remark: Do not pollute the friction pads.
Braking System
Rear Brake (SF) BR-39

(c) Self adjusting screw arbor thread;

(d) Contact position where the self-adjusting screw sleeve
and the brake shoe.

4. Mount the parking brake lever and the toggle plate

(a) Mount the parking brake lever and lock it with a new pin.
(b) Mount the toggle plate and a new open retainer ring.

5. Mount the adjuster on the rear brake shoe:

(a) Mount the adjuster;
(b) Mount the clearance-adjusting spring;

6. Mount the rear brake shoe:

(a) Mount the brake bracing wire on the parking brake lever;
(b) Mount the tension spring on the rear brake shoe;

(c) Encase the rear brake shoe in such way that the end shoe
is inserted in the wheel-brake cylinder.
(d) Mount the brake shoe pressure spring, pressure spring
cap and the claming pin.
Notice: Do not let the oil or lubricant touch the brake
shoe.
BR-40 Braking System
Rear Brake (SF)

7.Mount the front brake shoe:

(a) Mount the lower tension spring between the front shoe
and the back shoe.
(b) Mount the front brake shoe in such manner that the end
shoe is inserted in the wheel-brake cylinder, and mount
correctly the adjuster.

(c) Mount the pressure spring, pressure spring cap and

claming pin.
Notice: Do not let the oil or lubricant touch the brake
shoe.

(d) Mount the upper tension spring.

8. Check the operation of self-adjusting mechanism.

(a) Move the parking brake lever of rear brake shoe forward
and backward as shown in the drawing, check the self-
adjusting screw arbor to see whether it can rotate or not,
if not, check the rear brake to see which part has problem.

(b) Adjust the adjuster length and shorten it as can as possible.

(c) Mount the brake drum.
(d) Drag the parking brake lever to the max distance until no
quack-quack is heard.
Braking System
Rear Brake (SF) BR-41

9. Check the clearance between the brake shoe and the

brake drum:
(a) Tear down the brake drum.
(b) Measure the inner diameter of brake drum and the outer
diameter of brake shoe, then Check the difference of the
two diameters to see whether it falls within the standard
clearance range.
Shoe clearance: 0.6mm
If it is not correct, check the parking braking system.

10. Mount the brake drum and rear wheel;

Fastening torque
(145
10)mm

11. Fill the liquid container with brake liquid and exhaust
air in the braking system.

12. Check to see whether there is leakage of brake liquid

BR-42 Braking System
Load Sensing Proportion Valve

Load Sensing Proportion Valve

Element figure

location plate braking hose bracket

valve bracket

load inductive valve

snapping ring

flat washer

flat washer

load inductive spring

assembly
claming head I

inductive spring bracket

claming head II

split pin

shaft bush

Parts that cannot be reused after being used

Inspection on and Adjustment of hydraulic

pressure
1. Adjust the load on rear shaft
Load on rear shaft (including the vehicle weight): 800kg

2. Mount the load sensing proportion valve instruments

(SST) and exhaust the air.
 Braking System
Load Sensing Proportion Valve BR-43

3. Check the rear brake pressure on the condition that

the front brake pressure increases to 7,845kPa
Rear brake pressure: (4,315
490)kPa
kPa kPa
If the brake pressure is incorrect, adjust the hydraulic pressure.

4. Adjust the hydraulic pressure if necessary:

(a) Adjust the length of claming head II.
When lengthen the A distance, the rear brake pressure; if A
distance is shortened, the rear brake pressure reduces.
A
Initial adjustment: 78mm
Adjust range: (72-84)mm

(b) In case no even brake pressure is obtained after adjusting

the claming head, raise the valve or move it downward.
If the valve moves forward, the rear brake pressure will reduce;
if the valve moves downward, rear brake pressure will increase.
(c) Screw up the nuts.
(d) Adjust the length of claming head II again.
If it is unsuitable after re-adjustment, change the valve.

Disassembly of load sensing proportion valve

1. Tear down the claming head II from the bracket;

SST 2. Tear down the load sensing proportion valve cluster:

(a) Tear down the brake pipeline from the valve with SST.
BR-44 Braking System
Load Sensing Proportion Valve

(b) Tear down the mounting bolts of valve bracket, and load
sensing proportion valve cluster.

Mount of Load Sensing Proportion Valve

1. Mount the load sensing proportion valve cluster on the
frame.

2. Connect the claming head II with the bracket:

(a) Mount the claming head on the load inductive spring;
(b) Adjust the spacing A.
Initial adjustment: 78 mm;
(c) Mount the claming head II on the claming head bracket

SST 3. Connect the brake pipeline;

Connect the brake pipeline with SST.
Fastening torque

Dr SF
(18
2)N
m
SL SK SY SJ
(19
1)N
m

4. Adjust the rear shaft load

5. Adjust the valve:

(a) When drag downward the load inductive spring, the
valve piston shall move downward smoothly.
(b) When mount the valve body, the valve piston shall touch
the load inductive sensing spring lightly.
(c) Screw up the mounting nuts of valve body.
Braking System
Load Sensing Proportion Valve BR-45

6. Exhaust the air in braking system

7. Check and adjust the hydraulic pressure of load

sensing proportion valve.
 SR-1

Steering System
Page

Notice .......................................................................... SR-2

Troubleshooting .......................................................... SR-2
Inspection on Vehicle .................................................. SR-3
Steering Column ......................................................... SR-4
Manual Steering Gear ................................................. SR-9
Power Steering ............................................................ SR-11
General Introduction ................................................ SR-11
Inspection on vehicle ............................................... SR-13
Power Steering Oil Pump ........................................ SR-16
Power Steering Gear ............................................... SR-18
Steering linkage .......................................................... SR-20

SR
SR-2 Steering System
Notice and Troubleshooting

Notice
The parts change should be conducted correctly because
any error will affect the properties of steering system, or lead
to accidental or damage when driving.

Troubleshooting
Trouble Causes Inspection items

Difficulty in steering Unsuitable tire inflation Inflate the tire to specified pressure
Insufficient lubricant Lubricating the hanging devices
Over-large inclination Check the Alignment of Front Wheel
Steering gear joint wear Change the Steering gear joint
Lower swing arm ball head wear Change the lower swing arm ball
head;
Steering column seize-up Check the steering column
Steering gear unsuitable adjustment or damage Adjust or repair the gear.
Power steering conveyer looseness Adjust the conveyor.
Over-low liquid level in oil cup of steering pump Check the steering pump oil cup
Failure in power steering mechanism Check the power steering devices

Poor returning Unsuitable tire inflation Inflate the tire to specified pressure
Insufficient lubricant Lubricating the hanging devices.
Incorrect wheel alignment Check the Alignment of Front
Wheel
Steering column seize-up Check the steering column
Steering gear unsuitable adjustment or damage Change the steering gear.

Over-large play Front wheel bearing wear Change the front bearing
Steering drive shaft yoke wear Change the steering drive shaft
Lower swing arm ball head wear Change the swing arm ball head
Steering gear joint wear Change the steering gear joint
Steering gear unsuitable adjustment or damage Change the steering joint

Abnormal noise Steering drive lever looseness Tighten the steering drive lever
Steering gear joint wear Change the steering gear joint
Steering gear unsuitable adjustment or damage Change the steering gear
Oil lack or poor sealing of steering machine. Add the oil or change the sealing
washer Steering system inspection
on vehicle.
 Steering System
On-vehicle Inspection SR-3

On-vehicle Inspection
max play Steering wheel play
1.SR-18Check to see whether the steering wheel play is
correct;
Park the vehicle stably and align the tires in correct direction,
press the steering wheel with finger and swing it in left and
right direction. The play should not exceed the max play.
(Max play)
6
(Dr SF)
If the play is nor correct, adjust or repair the steering wheel as
requirement.
2. Adjust the steering wheel play:
(a) Align the wheel forward precisely;
(b) Loosen the locking nuts of steering gear;
(c) Rotate the adjusting screws of steering gear clockwise to
reduce the steering wheel play, while contrarotate the
adjusting screws to increase the steering wheel play.
Remark: screw the adjusting screws and enlarge the play a
little each time to check the adjusted play.

3. Check to see whether there is steering inconvenience

Rotate the steering wheel by half round in right and left
direction to check whether the play is correct, and whether the
wheel runs smoothly or any seize-up in its running.
4. Fix the adjusting screws and fasten the adjustable nut.

Oil level height

Check the oil level height in the steering gear housing.
Oil level height: flush with the filler opening.
If there oil is insufficient, add the gear oil and check to see
whether there is oil leakage.
SR-4 Steering System
Steering Column

Steering Column
Element figure of non-adjustable steering column
Dr
50
5

upper part of steering column

universal cardan joint

fixed support seat

dust cap

steering drive shaft

30
2
SL SK SY

upper part of
steering column

steering drive shaft

N
m
specified torque

 Steering System
Steering Column SR-5

Steering Column
Element figure of adjustable steering column
Dr SF

upper part of steering column

universal cardan joint

steering drive
shaft

SL SK SY

upper part of steering column

universal cardan joint

steering drive shaft

SJ

steering column

universal cardan joint

SR-6 Steering System
Steering Column

Dismantle of the steering wheel

1. Dismantle of the steering wheel;
(a) Take down the bugle cap;
(b) Pull down the bugle wire.
(c) Tear down the fixing nut of steering wheel.

2. Tear down the combined switch cover;

3. Tear down the cover at left bottom part.

4. Tear down the fixing bracket for the left-bottom cover.

5. Tear down the air passage;

6. Tear down the combined switch;

7. Tear down the fixed support seat bolts on front-wall panel;

8. Tear down the fixing bolts at upper part of steering

column, and

9. Tear down the connecting bolts of steering column

drive shaft.
10. Pull out the steering column.
 Steering System
Steering Column SR-7

SST
Mount of Steering Column
1. Mount the ignition switch assembly
Fix the ignition switch on the steering column with SST.

2. Mount the dust cap and fixed support seat of steering

column on the front-wall panel.

3. Mount the upper part of steering column;

Mount the upper part of steering column on the fixed bracket
with SST.

4. Connect the upper part of steering column and the

steering drive shaft with the universal cardan joint;

SST

5. Connect the steering drive shaft and the steering gear;

6. Mount the combined switch.

Fix the combined switch with SST.

SST

7. Mount the combined switch cover;

Fix the combined switch cover with SST.

SST
SR-8 Steering System
Steering Column

8. Mount the steering wheel:

(a) Screw up the fixing nuts of steering wheel according to
the specified torque.
Specified torque
Dr SF
(50
5)N.m
SL SK SY SJ
(30
2)N
m
(b) Connect the bugle wire;
(c
Mount the bugle cap.
 Steering System
Manual Steering Gear SR-9

Manual steering gear

Disassembly and mount of manual steering gear

steering drive shaft

manual steering gear box

worm shaft
96
10(Dr SL SK SY)

swing arm

245
25(Dr)

N
m
specified torque

Points on disassembly and mount

assembly mark
1. Disassemble the steering drive shaft:
(a) Loosen the fixing bolts at upper part of steering column;
(b) Tear down the connecting bolts of steering drive shaft;
(c) Mark the assembly marks on the steering drive shaft and
worm shaft;
(d) Slide the shaft backward to tear it down from the worm shaft.

2. Tear down the swing arm from the steering gear:

(a) Loosen the fixing nuts of swing arm;
(b) Tear down the swing arm from the steering gear with SST.
SST
SR-10 Steering System
Manual Steering Gear

3. Connect the swing arm to the steering gear:

(a) Mount the swing arm on the segmental gear shaft, and
mount the spring washer and steering arm.
(b) Screw up the swing arm nuts.
Fastening torque
(245
25)N
m(Dr)

4. Tear down the swing arm from the central transverse

SST drag rod;
Tear down the swing arm from the central transverse drag rod
with SST.
 Steering System
Power Steering (General Introduction) SR-11

Power steering
Introduction
steering drive shaft Principal of Power Steering
The power steering is a kind of hydraulic device that use
oil cup
the engine power to steer. The engine drive the power
steering oil pump to generate the hydraulic pressure, which
actuates the piston in steering gear, so that the worm shaft
can provide to the piston with a supplementary force, which
has relation with the pressure actuated on the piston.
Therefore, pressure increase is required if larger steering
force is needed, and the pressure variation is accomplished
power steering oil pump through the control valve.

power steering gear

control valve pump Intermediate position (forward straightly)

drain outlet The liquid from the power steering oil pump is sent to

power cylinde
the control valve, which, if locates at the intermediate, will
steering gear
allow the liquid to pass and enter into the drain outlet, finally
power piston return the pump. At this time, it is difficult to increase the
pressure; meanwhile, due to the equal pressures at the both
worm shaft
sides of the power piston, it cannot move toward either side.

segmental gear shaft

Pump

Steering time
When the steering drive shaft move toward either side,
the control valve will move together with it, in case one oil
passage is shut off, meanwhile open the other larger, the
liquid flow variation will increase the pressure, as result, the
unequal pressure at both sides of piston will make the piston
move toward the side of smaller pressure, therefore, the
liquid is pressed in the pump through the control valve.
SR-12 Steering System
Power Steering (Introduction)

Suggestion on maintenance
The failure of power steering system usually relates to the
steering difficulty due to lack of supplementary force. In such
case, it is the first to verify the problem is produced by the pump
or steering gear when repairing. In doing so, the problem can be
checked on vehicle with the pressure meter.

On-vehicle Inspection
As the power steering is a hydraulic pressure device, its
trouble usually caused by the lack of specified hydraulic
pressure or the abnormal work of control valve. As a result, it
cannot acquire the moderate hydraulic pressure.
In case the problem is caused by the pump, the steering
wheel will deflect toward right or left. On the other side, if the
problem is caused by control valve, when the steering wheel
rotates to left or right, the steering will become more difficult
due to the unequal supplementary force. However, when there
is wear on the piston sealing ring of power cylinder, it also cause
the hydraulic pressure loss that may lead into steering difficulty
toward right or left.
Before making inspection on vehicle, verify the power
steering system firstly to see whether there is air. If any, the air
volume will increase with the variation of hydraulic pressure,
which will cause the hydraulic pressure fluctuation that makes
the power steering work abnormally. In order to verify whether
there is any air in the system, check whether the liquid level
varies or not when the steering wheel rotates completely toward
the right or left. For instance, if there is air in the system, the air
will be compressed, which will reduce the liquid level
remarkably, when the steering wheel rotating. If there is no air
in system, the liquid level variation is very small even though
the hydraulic pressure increases. This is because the liquid
volume will not varies when being compressed. And the small
liquid level variation is caused by the expansion of hose
between the pump and steering gear when the hydraulic pres-
sure increasing.
Meanwhile, the air in system sometimes will cause the
pump or steering gear produce noise when the steering wheel
rotating completely toward a certain direction. After checking
or exchanging the pump or steering gear, the on-vehicle inspec-
tion should be often conducted to guarantee the normal work of
power steering system.
 Steering System
Power Steering (On-Vehicle Inspection) SR-13

power steering oil

tensioning wheel pump
On-vehicle inspection
Inspection on tension of driver conveyor
Measure the tension of drive conveyor.
Drive conveyor tension: under the condition of 98 N.
New conveyor: (5-7)mm
Old conveyor:
(7-9)mm
Remark:
crankshaft
ìnew conveyorî means the conveyor that is used on the
machine less than five minutes;
ìold conveyorî means the conveyor that is used on machine
more than five minutes

Check for height of liquid level

1. Keep the body in horizontal status
2. Increase the liquid temperature
When the engine runs idly by 1000 r/m or less, rotate the
steering wheel several times from the locking position to the
reverse locking position to increase the liquid temperature.

3. Check to see whether there is foam or emulsification;

Remark: the foam or emulsification shows there is air in the
system or the liquid level is over-low.
4. Check the liquid level height in oil cup;
Check the liquid level height and, if needed, add the oil.
SR-14 Steering System
Power Steering (On-Vehicle Inspection)

Change of power steering liquid

1. Tear down the oil-returning hose from the oil cup to
drain the liquid into the container;
2. Run the engine in the idle status, and rotate the
steering wheel toward the max rotating angle for
several times in right or left direction while draining the
liquid, until the oil in steering liquid is drained up.
3. Turn off the engine.

4. Connect the oil-returning pipe and inject the new

power steering liquid in the liquid tank;
Hydraulic oil type: No.8 Liquid drive oil (Q/SH003.01.012-88)

5. Start the engine, and make it running in the idle status.

Rotate the steering wheel to the max rotating angle repeatedly
several times, meanwhile, supplement new power steering
liquid in the liquid tank until there is no foam or turbidities in
the liquid tank, and the oil indicating lamp reaches the marked
range when the engine is turned off.

6. Tighten the liquid tank cover

7. Exhaust the air in the power steering system;

Ai-r bleeding in power steering system

1. Check the liquid level height in the liquid tank
Check the liquid level and, if needed, supplement the liquid.

2. Start the engine in the idle status and rotate the

steering wheel repeatedly to the max rotating angle
several times.
3. Turn off the engine and connect the ethane pipe and
bleeding plug.
4. Start the engine and rotate the steering wheel
repeatedly to the max rotating angle several times.
5. Locate the steering wheel at the intermediate position.
 Steering System
Power Steering (On-Vehicle Inspection) SR-15

6. Exhaust the air in steering system:

(a) Loosen the bleeding plug;
(b) Screw up the bleeding plug when there is no air bubble
exhausted from the pipeline.
Notice: take care not let the ethane pipe slide from the
bleeding plug, because the liquid is high in temperature
and pressure.

7. Check to see whether there is air bubble or turbidities

in the oil cup, and ensure the liquid level will not
exceed the max value when the engine stops,
Measure the liquid height under the condition of engine running,
RPM RPM
then turn off the engine and measure the liquid height again.
In case any problem is found, repeat the approaches of (5) and
(6) in Power Steering Liquid Change. If the problem still
exists, repair the power steering oil pump.
SR-16 Steering System
Power Steering (Oil Pump of Power Steering)

Oil Pump of Power Steering

Dismantle and Mount of Oil Pump of Power Steering

Gasoline Engine Series

power steering oil pump

power steering oil pump bracket

belt pulley

HP oil pipe

LP oil pipe

driving belt

Diesel Engine Series

HP oil pipe

oil cup

belt pulley
LP oil pipe

power steering oil pump

power steering oil pump bracket

Steering System
Power Steering (Oil Pump of Power Steering) SR-17

Points on disassembly and mount

1. Disassemble and connect the pressure pipe;
Tear down and mount the pressure pipeline on the power
SST steering oil pump with SST.
2. Loosen the belt pulley nuts;
Press the driving belt by hand to fix the belt pulley to immo-
bilize and loosen the belt pulley nut.
3. Adjust the driving belt tension after mounting the
power steering oil pump;
(See page SR-13)
SR-18 Steering System
Power Steering Gear

Power steering gear

Disassembly and mount of power steering gear
Dr SF SJ
LP oil pipe

steering drive shaft(Dr SF)

HP oil pipe steering drive shaft(SJ)
power steering gear

96
10(Dr)
145
10(SF)
78
10(SJ)

swing arm
245
25

steering drag rod

91
10(Dr SF)

pi=ph=pv LP oil pipe

HP oil pipe

steering drive shaft

96
10

power steering gear

swing arm

245
25

N
m
specified torque

 Steering System
Power Steering (Power Steering Gear) SR-19

Points on disassembly and mount

1. Tear down the HP oil pipe and LP oil pipe from the
steering gear;
Tear down the HP oil pipe and LP oil pipe from the steering
gear.

assembly mark 2. Tear down the steering power shaft

(a) Make assembly marks on the steering drive shaft and the
worm shaft.
(b) Tear down the connecting bolts of drive shaft
(c) Dismantle the steering drive shaft from the worm shaft.

3. Tear down and connect the swing arm:

(a) Tear down the swing arm fixing bolts;
(b) Tear down the swing arm from the steering gear with SST.

SST

4. Tear down the fixing bolts of steering gear;

Tear down the fixing bolts from the steering gear and then the
steering gear can be disassembled.
SR-20 Steering system - Steering Linkage

Steering Linkage
Dismantle and mount of steering linkage

side drag rod assembly

joint clip
80
10(Dr)
83
10(SL SK SY) 91
10(Dr SF)
142
10(SF) 90
10(SL SK SY)
78
10(SJ) 78
10(SJ)

auxiliary steering arm 91
10(Dr)

59
5(SF)

intermediate lateral drag rod assembly

N
m
specified torque

Parts that cannot be reused after being used

Remark
(a) Where the bolts of recirculating ball are connected with
the arm or lever, the lubricant on its surface should be
cleaned.
(b) Screw up the bolts and nuts of re-circulating ball to the
specified torque, and then screw the nut forward to the
degree that the split pin can be encased in.
(c) Check the Alignment of Front Wheel and side slip after
any part of steering linkage is mounted.
 Steering System - Steering Linkage SR-21

Points on Dismantle and Mount

1. Tear down and connect the swing arm on segmental
gear shaft:
SST
(a) Loosen the swing arm nuts;
(b) Tear down the swing arm from the segmental gear shaft
with SST;
(c) Mount the swing arm on the segmental gear shaft and
mount the spring washer and nut when connecting.

2. Tear down the swing arm from the intermediate lateral

drag rod;
SST
Tear down the swing arm from the intermediate lateral drag
rod with SST.

SST 3. Tear down the side drag rod assembly from the
intermediate lateral drag rod;
Use the SST to tear down the side drag rod assembly from the
intermediate lateral drag rod;

4. Connect the side drag rod assembly:

(a) Screw the two ends in the side drag rod.
A A
A=A
Remark: the thread length at the two ends that cannot screw in
the side drag rod should be equal.

B B

B=B

SR-22 Steering System
Steering Linkage

(b) Rotate the two ends of side drag rod to make them
intercross at 90
angle, and connect the side drag rod.

5. Tear down the auxiliary steering arm from the

SST
intermediate lateral drag rod.
Tear down the auxiliary steering arm from the intermediate
lateral drag rod with SST.
 BE-1

Body Electric System

Page
Protective box Location and content ............................ BE-6
Power Supply System .................................................. BE-16
Starting System ............................................................ BE-17
Lighting System ........................................................... BE-19
Combination Instrument ............................................... BE-32
Backup Radar System ................................................. BE-39
Wiping and Washing System ....................................... BE-40
Central control lock and Power regulator System ......... BE-50
Acoustical Equipment System ..................................... BE-61
Wire Harness Arrangement.......................................... BE-68

BE
BE-2 Body Electric System
Brief Introduction

Brief Introduction
1. Power supply system
The power supply system includes accumulator, generator and its adjustor. Generator is the main power supply; the
accumulator is the auxiliary power supply. The generator, parallel with the accumulator, is equipped with the
adjustor, which is used to maintain the voltage of generator stable when the rotating velocity and the load varies.
2. Starting System
Which includes the direct current motor, drive mechanism and control device, etc. its performance is to start the
engine.
3. Lighting system
Which includes various lighting lamps inside and outside of the body and their control device; they are used mainly
to guarantee safety driving in night.
4. Alarming System
Which includes the electric horn, flasher and various service signal indicating lamps, etc. they are mainly used to
guarantee the physical and driving safe when driving.
5. Auxiliary Electric Appliance System
It includes the electric wiper, air-conditioner, recorder and cigarette lighter, etc.

English letters for wiring colors code:

R
B =black Bl =blue R =red Br =brown
red Lg =reseda V =purple G =green O =orange
W =white Gr =gray P =pink Y =yellow
First letter stands for the basic color, while the second for the
R/G stripe color.

red green

1. The codes of sockets of socket plugging element are

complied from left to right.
1 2 3 3 2 N 2. The codes of sockets of socket plugging element are
compiled from right to left.
4 5 S 6 5 4 Remark: all of plugging elements are watched from the in-
wiring direction.
socket plugging element plug plugging element

3. Comparison between plug and socket plugging elements

The plug and socket plugging elements are classified accord-
ing to their in-built socket shape.
(a) All of plugging element are marked according to the
opening end and are locked at their tops.
(b) When pulling the plugging element, pull the plugging
element itself instead of wire.
Remark: before pulling the plugging element, check the
socket plugging plug plugging element plugging element that you want to disconnect first to verify
element
their classifications.
 Body Electric System
Brief Introduction BE-3

pull up pull up

press down press down

10A same rated current 10A Change of fuse and maxi-fuse

Remark: in case of exchanging the fuse or maxi-fuse, the fuse
or maxi-fuse with same rated current should be used.

Notice:
1. Before exchanging the fuse or maxi-fuse, all electric
appliances and ignition switches should be turned off
firstly. And the rated current of fuse or maxi-fuse should
not be exceeded.
2. When disassembling or assembling the fuse, the
disassembly and assembly tools must be used. And they
must be pulled out or plugged in vertically. No bend is
allowed because the bend will make the connecting
terminals depart away, and thus poor connection will
occur. In case the fuse or maxi-fuse is burned, it shows
there is short circuit. In such situation, the systematic
inspection should be conducted by the qualified
technician.
Remark: the disassembly and assembly tools are put on the
protective box cover.
BE-4 Body Electric System
Brief Introduction

How to make systematic inspection

The inspection order is a simple troubleshooting approach, which is used to check and diagnose the failure on vehicle
when there is part (wiring and plugging elements excluded) failure in the systematic operation or presupposed
system.
Following items should be considered firstly when checking the failure.

wiring failure

open circuit or short circuit of electric wiring

failure in plugging element connection or terminal connection

failure of fuse or maxi-fuse

Notice:
1. The inspection is conducted on vehicle when the system is in operation, therefore, security should be
taken into account when checking.
2. Care should be paid not to make short circuit in the system under the condition that the accumulator is
directly connected, and the applicable voltage should be selected correctly.

IG terminal connected to ignigtion Voltage inspection

switch of SW
(a) Verify the voltage situation at the inspection spots.
For example:
fuse
Put the ignition switch at
ON
position


Put the ignition switch and SW1 at
ON
position;

Put the ignition switch of SW, SW1 and the relay at

ON
position (SW2 at
OFF
position)
SW1
(b) Connect the cathode lead (-) to the normal grounding


place or the cathode terminal of accumulator with the
0 12
voltmeter; while connecting the positive lead (+) to the
V plugging element or part terminal. Such inspection can
relay
be conducted with the test bubble instead of voltmeter.

SW2 electromagnetic coil

0
Inspection on Conductance and Resistance
ohmn meter (a) Disconnect the terminal or wire of accumulator to guar-

antee there is no voltage between the inspection sports.
(b) Connect the two measuring leads of ohmn meter with the
inspection spots.

SW
 Body Electric System
Brief Introduction BE-5

0

If there is diode in the circuit, connect the two leads in reverse

0
polar and make another inspection. When the cathode lead (-)
ohmn meter is connected with the positive (+) side of diode, and the
K
K

positive (+) lead should be connected with the cathode (-) lead
of diode, the diode should conduct, while the two leads
connected to the reverse polar, the diode should not contact.
Remark: the specification may be not same due to different
diode testing meter types; therefore, the application instruction for
testing meter should be referred before the inspection.
Check the light emitting diode (LED) according to the same

0
0 approach for diode inspection.
ohmn Remark:
K
K The testing meter should be used the one with 3V voltage or the

one has larger resistance than that in circuit.
If no suitable testing meter is applied, the voltage of accumu-
lator may be added to check the LED to see whether it is
lighted.
LED
(c) Use the voltage or ohmn meter with high-impedance
(min voltage of 10 KV) to diagnose the failure in electric
digital type analogue type circuit.

D
C
DC V

LG terminal of ignition switch Check to see whether there is short circuit

(a) Tear down the burned fuse and remove all loads from
the fuse.
fuse box
testing bubble (b) Connect the testing bubble at the fuse position;
short circuit
(c) Verify the situation of testing bubble position:
For example:
SW1
Put the ignition switch of SW at
ON
position;
short circuit

disconnectiong
Put the ignition switch of SW and SW1 at

ON
position;

Put the ignition switch of SW, SW1 and Relay at
disconnection

ON
position (which connects with the relay), and put
electromagnetic
SW2 at
OFF

) position (or disconnect the SW2).
coil
short circuit
(d) Disconnect or re-connect the plugging elements when
observing the testing bubble. In case the testing bubble
disconnection
keeps lighting, which shows there is short circuit between
SW2 electromagnetic the plugging elements; if the testing bubble extinguishes,
coil there is short circuit between the plugging elements.
(e) Shake the trouble wire alongside the body to locate the
BE-6 Body Electric System
Protective Box Position and Content

Position and content of protective box

Parts mounting Position

Dr SF

protective box III

time-delay relay protective box I

SL SK SY SJ

protective box I

flasher relay

pre-heating timer horn relay

rear defrost relay SY SL diesel SL diesel
SY diesel SY diesel
rear air-conditioning relay SY
Body Electric System
Protective Box Position and Content BE-7

Parts Mounting Position (Continued)

ECU relay

fuel pump relay

air-conditioner relay

preheating relay
diesel

protective box II
BE-8 Body Electric System
Protective Box Position and Content

Dr Content of Protective Box

1 protective box I
fuse relay

1.Small lamp 10A A electric window relay
A 2.Rain brus 20A B. small lamp relay
3.Ceiling lamp 10A C.(flasher)
4.(Cigarette lighter) 15A
(plugging elements of ceiling

5.Back -u 15A lamp wire harness)
B
6.Brake 10A
(plugging elements of wire
7.electric window 30A harness in engine room)
8.Instrument 10A
C fuel delivery/break electromagnetic valve10A(diesel

9.Central control lock 15A
1 2 3

4 5 6

7 8 9

FUSE
SL SK
1. Protection 10A
2. Unload
3. Charging 10A
4. Back-up 10A
U N 5. ECU 10A
6. Unload
V O 7. Rain wiper 10A
8. Stop lamp 10A
NM P
9. Ceiling lamp 10A
NN Q 10. Central control lock 15A
11. Dual flasher 10A
NO R
12. EC 10A
13. Fuel pump 10A
NP S
14. Cigarette lighter 15A
NQ T
 Body Electric System
Protective Box Position and Content BE-9

Protective bos I (continued)

SF

A

B C

D E

1 2 3 4 5 6

7 8 9 10 11 12

13 14 15 16 17 18

fuse relay
1. Small lamp 10A A. electromagnetic fan relay
2. Brake 5A B. lasher
3. Ceiling lamp 5A C. electromagnetic fan relay
4. Central control lock 15A D. small lamp relay
5. Electric rocker gear 30A E. electric window relay
6. Dual flasher 10A
7. Cigarette lighter 15A
8. Rear vision mirror 5A (1) plugging elements of ceiling lamp wire harness
9. Unload (2) plugging elements of wire harness at front left door
10. Acoustic device 15A (3)plugging elements of wire harness in engine room
11. Rear window 20A
12. Electromagnetic fan 10A
13. Instrument 5A
14. Back-up lamp 5A
15. Rain brush 10A
16. Steering 5A
17. Unload
18. Unload
BE-10 Body Electric System
Protective Box Position Content

pv=pg 1Protective box I (continued)

Fuse Vehicle
Model
1. Standby 30A
1
Standby 20A SJ
2 2. Standby 15A SY
Standby 10A SJ
3 4 6 7
5 3. Standby 10A SY SJ
4. Unload SY
Bass bubble 10A SJ
8 9 10 11
Power amplification 10 A top SY
5. Unload SY SJ
6. Unload SY SJ
12 13 14 15 7. Unload SY SJ
8. Air-conditioner 10A SY SJ
9. Charging 10A SY
16 17 18 19 Instrument 10A SJ
10.ECU 10A SY SJ
11.Back-up lamp 10A SY SJ
20 21 22 23 12.Cigarette lighter 30A SY SJ
receiver
13.Unload SY
Refrigerant 10A SJ top SY
14.Unload SY SJ
15.Steering electric window 10A SY
Humid display of steering 10A SJ
sindicating lamp
16.Stop lamp 10A SY SJ
17.Power aerial of inside lamp 10A SY SJ
18.Central control lock 20A SY SJ
19.Dual flasher 10A SY SJ
20.Front rain brush 10A SY SJ
21.Rear air-conditioner 15A SY
Unload SJ
22.Rear defroster 15A SY
Unload SJ
23.Rear rain brush 10A SY
Unload SJ
 Body Electric System
Protective Box Position and Content BE-11

SLDiesel SYDiesel 1.Protective box I (continued)

Fuse Vehicle model
1. Standby 10A (SL diesel)(SY diesel)
1
2. Standby 15A (SL diesel) (SY diesel)
2 3. Standby 30A (SL diesel) (SY diesel)
3 4. Unload (SL diesel) (SY diesel)
4 5 6 7
5. Unload (SL diesel) (SY diesel)
6. Unload (SL diesel) (SY diesel)
7. Unload (SL diesel) (SY diesel)
8 9 NM 11
8. Start 10A (SL diesel) (SY diesel)
9. Rear defroster 15A (SY diesel)
Unload (SL diesel)
12 13 14 15
10.Cigarette lighter
and receiver 30A (SY diesel)
Cigarette lighter 15A (SL diesel)
16 17 18 19 11.Rear rain brush 10A (SY diesel)
Unload (SL diesel)
12.Front rain brush 15A (SY diesel)
20 21 22 23 Rain brush 5A (SL diesel)
13.Steering 10A (SY diesel)
Dual flasher 10A (SL diesel)
14.Preheating 15A (SL diesel)(SY diesel)
15.Electric window 30A (SL diesel)(SY diesel)
16.Small lamp 10A (SL diesel)(SY diesel)
17.Stop lamp 10A (SL diesel)(SY diesel)
18.Inside lamp
and electric aerial 15A (SY diesel)
eiling lamp 10A (SL diesel)
19.Central control lock 20A (SY diesel)
Central control lock 15A (SL diesel)
20.Rear air-conditioner 15A (SY diesel)
Unload (SL diesel)
21.Unload (SL diesel)(SY diesel)
Refrigerant 10A (top SY diesel)
22.Unload (SL diesel )(SY diesel)
Power amplification 10A (top SY diesel)
23.Unload (SL diesel)(SY diesel)
BE-12 Body Electric System
Protective Box Position and Content

Protective box II
Dr SF

1 2 3

4 5 6 A

7 8 9

C B

Fuse Vehicle Relay vehicle

1. Front fog lamp 15A Dr A. electromagnetic fan relay Dr
Unload SF charging relay Dr diesel
2. Electromagnetic fan 15A Dr electric horn relay SF
ECU1 10A SF B. large lamp Dr SF
3. Large lamp 10A Dr C. frost relay Dr SF
Horn 15A SF
4. Horn 15A Dr
Lower beam 10A SF
5. ECU1 10A Dr (1) plugging elements of
wire harness in engine room Dr
Charging 10A Dr diesel none SF
Rear frost 5A SF (2) plugging elements of
wire harness in engine room Dr SF
6. Large lamp 10A Dr (3) plugging elements of
wire harness in engine room Dr SF
ECU2 10A SF
7. Rear frost 10A Dr
Upper beam 10A SF
8. ECU2 10A Dr
Preheating 10A Dr diesel
Front fog lamp 10A SF
9. Fuel pump 10A Dr SF
Unload Dr diesel
 Body Electric System
Protective Box Position and Content BE-13

Protective box II (continued)

SL SK

1 2 3 4 5 6 7 8 9 10 11 12 13

14 A B
17

16 15
C D

I H
G E F

Fuse Vehicle Relay Vehicle

1. Standby 10A SL SK A.electromagnetic fan relay SL SK
2. Standby 10A SL SK small lamp relay (SL diesel)
3. Standby 30A SL SK B.electric window relay SL SK
20A (SL diesel) cold start relay (SL diesel)
4. Rear fog lamp 10A SL SK C.frost relay SL SKLeft
large lamp 10A (SL diesel) charging relay) (SL diesel)
5. Front fog lamp 10A SL SK D.blower relay) SL SK
Right large lamp 10A (SL diesel) thermostatic relay (SL diesel)
6. Small lamp 10A SL SK E.small lamp relay SL SK
Air-conditioner 10A (SL diesel) heating relay (SL diesel)
7. Electric horn 10A SL SK F.large lamp relay SL SK
Warm air 20A (SL diesel) G.air-conditioner relay SL SK
8. Electric window 30A SL SK frost relay (SL diesel)
Unloa (SL diesel) H.rain-brusher intermissive relay SL SK
9. A/C 10A SL SK I.diod SL SK
Charging 10A (SL diesel)
10.Air blower 30A SL SK
Electric horn 10A (SL diesel)
11.Electronic fan 10A SL SK
Dual flasher 10A (SL diesel)
12.Right large lamp 10A SL SK
Unload (SL diesel)
13.Left large lamp 10A SL SK
Fog lamp 10A (SL diesel)
14.60A fuse SL SK
15.60A fuse SL SK
16.30A fuse SL SK
17.30A fuse SL SK
Unload SL diesel
BE-14 Body Electric System
Protective Box Position and Content

Protective box II (continued)

SY SJ

1 2 3 4 5 6 7 8 9 10 11 12 13

14 A B
17

16 15
C D

H
I
G E F

Fuse Vehicle Relay Vehicle

1. Standby 10A SY SJ A. electromagnetic fan relay SY SJ
2. Standby 10A SY SJ small lamp relay (SY diesel)
3. Standby 30A SY SJ B. electric window relay SY SJ
4. Rear fog lamp 10A SY SJ cold start relay (SY diesel)
Left large lamp 10A (SY diesel) air-conditioner relay SJ
5. Front fog lamp 10A SY SJ C. frost relay SY SJ
Right large lamp 10A (SY diesel) charging relay (SY diesel)
6. Small lamp 10A SY SJ D. blower relay SY SJ
Air-conditioner 10A (SY diesel) thermostatic relay (SY diesel)
7. Electric horn 10A SY SJ E. small lamp relay SY SJ
Warm air 20A (SY diesel) heating relay (SY diesel)
8. ECM 10A SY SJ rear defrost relay SJ
Unload (SY diesel) F. large lamp SY SJ
9. Fuel pump 10A SY SJ H. rain-brusher intermissive relay SY SJ
Charging 10A (SY DIESEL) I. diode SY SJ
10. Air blower 30A SY SJ
Electric horn 10A (SY diesel)
11. Electronic fan 10A SY SJ
Dual flasher 10A (SY diesel)
12. Right large lamp 10A SY SJ
Rear fog lamp 10A (SY diesel)
13. Left large lamp 10A SY SJ
Front fog lamp 10A (SY diesel)
14. 60A fuse SY SJ
15. 60A fuse SY SJ
16. 30A fuse SY SJ
17. 30A fuse SY SJ
Unload (SY diesel)
 Body Electric System
Protective Box Position and Content BE-15

Dr SF Protective box III

Fuse Vehicle model
1. Compressor 10A Dr SF
2. Unload SF
A/C 10A Dr
A 3. Warm air 30A Dr SF

3
BE-16 Body Electric System
Power Supply System

Power supply system

The power supply system includes the accumulator and the generator, the latter is the main power supply while the
accumulator is the auxiliary power supply. The two power supplies are in paralleling connection.

fuse
ignition switch 4
5






fuse
ACC ON ST



charging indicating lamp

fuse
battery

generator

ignition switch SL SK SY SJ Dr SF

4 3 2 1 5 4 3 2 1

8 7 6 5 10 9 8 7 6

vehicle models in parenthesis belongs to Dr and SF

 Body Electric System
Starting System BE-17

Starting system
The starter, powered by the accumulator, is driven by the direct current motor and is in normal operation through
the drive device and control mechanism.

fuse
4
5

ignition switch 5
3

1
4

SL SK SY SJ
3
2

ACC ON ST
4 3 2 1

8 7 6 5

Dr SF
starter

5 4 3 2 1
battery

10 9 8 7 6

Vehicle models in the parenthesis belong to the Dr SF model.

BE-18 Body Electric System
Starting System

Parts inspection
Ignition switch
Check the conductance situation of the switch

terminal 4 1 5 3
OFF ACC SLdiesel SYdiesel switch position B Bl B/Y W/Bl
LOCK
LOCK
4 3 2 1
ACC
8 7 6 5
ON
ON START

terminal 4 1 5 3
pi=ph=pv=pg
switch position R G W R/W
LOCK
START 4 3 2 1
ACC
LOCK ACC 8 7 6 5
ON

START
aê=pc
ON terminal 5/10 4 3 2 9

switch position R G W R/W Y

R Q P O N
LOCK

NM V U T ACC

ON
START
START

Remark: in case the conductance fails to satisfy the specified requirement, change the switch.
 Body Electric System
Lighting System BE-19

Lighting system
The lighting system includes the front combination lamp, rear combination lamp, fog lamp, inside lamp, instrument
lighting lamp, air-conditioner panel lighting lamp and various signal indicating lamps. The small lamps shown in the
small lamp system drawing include the instrument lighting lamp, air-conditioner panel lighting lamp, fog lamp, license
lamp and ashtray lighting lamp.

Upper/lower beam lighting system

Dr SF

fuse

large lamp relay

1
1

10
17

small light
light
surpass vehicle headlamp
fuse

low beam
high beam large lamp switch
battery

3
3

passing-light headlamp

lamp
upper beam indicating
main-beam headlamp

combined switch

7 6 5 4 3 2 1

14 13 12 11 10 9 8

21 20 19 18 17 16 15

The vehicle model in the parenthesis belongs to Dr model.

BE-20 Body Electric System
Lighting System

Upper/lower beam lighting system (continued)

SL SK SY SJ

frse

large lamp relay

frse
T
7
small lamp
upper beam indicating lamp

10 8 head lamp

lower beam head lamp switch

battery

upper beam

out-drive N

connecting to combination instrument

combined switch

7 6 5 4 3 2
8 1

NS 15 14 13 12 11 10 9
 Body Electric System - Lighting System BE-21

Small lamp, steering and alarming system

Small lamp system

Dr

fuse

fuse
small lamp relay

fog lamp indicating

fog lamp relay

front small lamp
lamp
ear small lampv
left rear fog lam
license lamp

8 3 right rear fog lamp

receiver lighting lamp

ON ON

OFF OFF
battery

air-conditioner panel lamp

small lamp switch

10 1
alarming switch lamp

fog lamp switch

instrument lighting system

combined switch
fog-lamp switch lamp

7 6 5 4 3 2 1
1
14 13 12 11 10 9 8
3 2
21 20 19 18 17 16 15
BE-22 Body Electric System
Lighting System

Small lamp system

SF

fuse

front small lamp

rear small lamp

foglamp relay
small lamp relay

license lamp front fog lamp indicating lamp

instrument lighting system
front left fog lamp
defroster switch lamp
front rear fog lamp
8 alarming switch lamp 6
rear fog lamp indicating lamp
ON ON N
front fog-lamp switch lamp
battery

OFF OFF left rear fog lamp

small lamp switch front fog lamp switch

rear fog-lamp switch lamp
right rear fog lamp
ON OFF
tail-door switch lamp
10 rear fog-lamp switch

CD switch lamp

air-conditioner panel lamp

cigarette lighter switch lamp

combined switch

front fog lamp switch rear fog-lamp switch

7 6 5 4 3 2 1

6 5 4 3 2 1 4 3 2 1
14 13 12 11 10 9 8
10 9 8 7 6 5
21 20 19 18 17 16 15
 Body Electric System
Lighting System BE-23

Small lamp steering system

SL SK SY SJ

fuse

ignition switch
flashing lamp
small lamp relay
E B 10
i
left
2
alarming
right
switch
5 ON OFF
steering switc 1
4
6

small lamp 8
small lamp

large lamp
battery

4
small lamp switch 5

combined switch
alarming switch lamp stop lamp switch
7 6 5 4 3 2
8 1 4 3 2 1 1
16 15 14 13 12 11 10 9 2
8 7 6 5
BE-24 Body Electric System
Lighting System

Steering and Alarming System

alarming lamp switch

Dr
OFF ON left turn indicating lamp

3
flasher front left turn lamp
B i 2
1 (turn lamp) on left side)
fuse
E
ON
rear left turn lamp
OFF
16
horn switch 2
right turn indicating lamp
9
left right (right front turn lamp
steering switch
electric horn

turn lamp) on right side

(rear right turn lamp)

battery

combination switch lamp)

alarming switch
7 6 5 4 3 2 1

1
14 13 12 11 10 9 8

3 2
21 20 19 18 17 16 15
 Body Electric System
Lighting System BE-25

Steering and Alarming System (continued)

SF
alarming lamp switch
ON OFF steering switchleft
fuse 2 16
6 2
ignition switch
5 9 tight
3
L left turn indicating lamp
4 B
3 1 front left turn lamp

flasher
E
5 fuse
turn lamp) on left side
ACC

ON
ST

rear left turn lamp

fuse

right turn indicating lamp

battery

right front turn lamp)

turn lamp on right side

rear tight turn lamp

combined switch

7 6 5 4 3 2 1
alarming switch ignition switch

14 13 12 11 10 9 8 6 5 4 3 2 1 5 4 3 2 1

21 20 19 18 17 16 15 10 9 8 7 10 9 8 7 6
BE-26 Body Electric System
Lighting System

Inspection on Common Failure

FailurePossible Causes Repairing approaches Remark
Only one lamp doesn
t work Burn off bubble Change the bubble
Grounding failure of socket or wiring Make reparation as required.

The front combination Burn off fuse Change the fuselamp don
t work
Failure of large lamp relay Check the relay
Failure of combinationswitch Check the switch
Wiring or grounding failureMake Make reparation as required

Upper beam lamp doesn
t work Failure of combination switch Check the switch
Wiring or grounding failure Make reparation as required

The rear combined tail lampand Burn off fuse in tail lamp Change the fuse and check
license lamp don
t work whether there is short circuit
Burn off maxi-fuse Change the maxi-fuse;
Failure of combined switch Check the switch;
Wiring or grounding failure Make reparation as required.

Alarming lamp doesn
t Change the fuse and check to see Change the fuse and check Dr SF
workBurn off horn fuse whether there is short circuit
Failure of steering signal flasher Check the flasher
Failure of steering signal/alarming switch Check the switch
Wiring or grounding failure Make reparation as required.
One side of the steering Failure of steering signal switch Check the switch
signal doesnít flash Wiring or grounding failure Make reparation as required.

Abnormal steering signal Burn off horn fuse Change the fuse and check to see Dr SF
whether there is short circuit
Failure of steering signal flasher Check the flasher
Failure of steering signal/alarming switch Check the switch
Wiring or groun ding failure Make reparation as required.
 Body Electric System
Lighting System BE-27

Parts inspection
Combined switch conductance

Dr
Terminal 1 8 10 17 3 7 2 9

function Bl/W Bl/Br B B/Y B/W B G/Y G/R

OFF
small
Lamp switch
lamp
Large
7 6 5 4 3 2 1 lamp
Lower
14 13 12 11 10 9 8 beam
Dimmer
21 20 NV 18 17 15 switch upper
16
beam
Leftturnn

steering right turn

switch
central

overtake

SF
Termina 1 8 7 10 3 15 2 9

function Bl/W Bl/Br B B/Y B/W B G/Y G/R

OFF
small
Lamp switch
lamp
large
7 6 5 4 3 O 1 lamp
lower
NQ NP NO NN NM V U dimmer beam
switch upper
21 20 19 18 17 16 NR
beam

left turn
steering
right
switch turn

central

over drive

SL SK SY SJ
terminal 16 7 15 10 8 9 1 4 3 5

function Bl/Br Bl/W B B/W B/Y Bl/W B G/Y G/R Br

OFF

lampswitch small lamp

7 6 5 4 3 2 large lamp
8 1
16 15 14 13 12 11 10 9 dimmer
lower beam

switch
upper beam

right turn
wteering
switch left turn

central

over drive
BE-28 Body Electric System
Lighting System

Combined Switch conductance (continued)

SLDiesel SYDiesel
Terminal 16 7 15 10 8 9 1 4 3 5

function R R/Bl B R/Y R/B R/Bl B G/B G/W Br

OFF

Small
Lamp switch
lamp
Small
7 6 5 4 3 2
lamp
8 1
16 15 14 13 12 11 10 9 Lower
beam
Dimmer
switch Left
steering
upper
beam
Right
steering
to
switch
central

overdrive

In case the conductance situation fails to satisfy the specified requirement, change the switch.

Conductance of Alarming Switch

Dr

Terminal 1 2 3

switch position G/B G/Y G/R

1
OFF

3 2
ON

SF

Terminal 8 9 1 2 3 4 5 6

switch position B G/W P/G G/B P/B Br/Bl G/R G/Y

6 5 4 3 2 1
OFF

10 9 8 7

ON
 Body Electric System
Lighting System BE-29

Conductance of Alarming Switch (continued)

SL SK SY SJ

Terminal
1 2 3 4 5 6 7 8
switch G/B G/R G/Y Br Y W/Br B G/W
position

4 3 2 1
OFF

8 7 6 5

ON

SLDiesel SYDiesel
Terminal 1 2 3 4 5 6 7 8

switch G G/W G/B Br Y Br/W B G/R

position

4 3 2 1
OFF

8 7 6 5

ON

In case the conductance fails to satisfy the specified requirement, change the switch.

Conductance of Fog-lamp Switch

Dr

Terminal 1 3
switch B Bl/B
position
1
OFF
3 2

ON
BE-30 Body Electric System
Lighting System

Conductance of Fog-lamp Switch

SF
Terminal 2 5 6 7 3 U V NM
switch B P/Y B G/W G/W Nothing Nothing Nothing
position

1 2 3 4 OFF

5 S 7 8 9 10 ON

SF
Terminal 1 2 3 4 5 6

switch B B W Nothing G/W W

position

1 2 OFF

3 4 5 6
ON

SL SK SY SJ
Terminal R O P S
switch G/W B _ s
position
3 2 1
OFF

6 5 4

ON

SLDiesel SYDiesel
Terminal R O P S
switch G/R B B Bl
position
3 2 1
OFF

6 5 4
ON
 Body Electric System
Lighting System BE-31

Conductance of Large Lamp Relay

Dr SF Terminal
30 85 85 86 87 30
30 85
status

Fixed

86 Load accumulator voltage

87 87 86
on the terminal 85,86.

SL SK SY SJ Terminal
30 85 85 86 87 30
30 85
status

Fixed

86 Load accumulator voltage

87 87 86
on the terminal 85,86.

In case the conductance of above-mentioned switch fails to satisfy the specified requirement, change the switch.

Conductance of Flasher Relay

1. Connect the positive lead from the accumulator to the
L
E terminal B, and the cathode lead to terminal E.
B
2. Connect two turn signal lamps to the terminal L and E and
check the flashing situation of the two bubbles.
The turn signal lamp should flash 85
10 per minute, in
case the flashing frequency fails to satisfy the specified
requirement, change the flasher relay.

turn signal lamp

BE-32 Body Electric System
Combination Instrument

Combination instrument
Electric circuit diagram

 
^N ^NS  _N _NP

 

 

Dr rear fog lamp indicating lamp

aêaáÉëÉä
A3 rear fog lamp indicating lamp
rear window/defroster indicating lamp A3
A4 upper beam indicating lamp
upper beam indicating lamp B12
B12 front fog-lamp indicating lamp
front fog-lamp indicating lamp B13
B13 A13
B3
connection with sensor
A13
B3
connected with sensor B5
water B5 connected water
thermometer
connected thermometer
with
with A10
A10 negative tachometer connected with revolution signal
negative tachometer connected with revolution signal B4 connected
B4 connected pole connected with sensor anode with
pole connected with sensor anode with A15
speedometer connected with sensor positive
speedometer
connected with sensor
A15 positive A14 pole
pole
A14

fuel gauge connected with sensor

fuel gauge
connected with sensor A12
A12 oil-water separation indicating lamp
A4
braking liquid level indicating lamp
B11 safety belt indicating lamp
parking brake indicating lamp B11
B10 parking brake indicating lamp
safety airbag indicating lamp B10
B9 braking liquid level indicating lamp
low oil pressure indicating lamp B9
A10 B8 low oil pressure indicating lamp
connected engine failure indicating lamp A10 B8
with B6 engine failure indicating lamp
B6
four wheel drive indicating lamp connected
positive A9 with four wheel drive indicating lamp
A9
pole generator preheating indicating lamp
A8 positive generator preheating indicating lamp
A8
fuel alarming indicating lamp
A7 pole fuel alarming indicating lamp
accumulator charging indicating lamp
A7
A6 accumulator charging indicating lamp
ABS failure indicating lamp
A6
ABS failure indicating lamp
A5 A5
left turn indicating lamp left turn indicating lamp
B1 B1
right turn indicating lamp right turn indicating lamp
A16 A16
A2
A2 instrument interior
connected instrument interior
lighting lamp
connected with lighting lamp
with A1 negative A1
negative pole
pole

liquid crystal back-light lamp liquid crystal back-light lamp

 Body Electric System
Combination Instrument BE-33

Electric circuit diagram (continued)

SF
A3 connected left turn indicating lamp
with negative pole B15
right turn indicating lamp
A1 connected A2
with positive pole upper beam indicating lamp
B16
rear fog lamp indicating lamp
A13
rear window/defroster indicating lamp
A16
front fog-lamp indicating lamp
B13
connected with sensor
water
B5
thermometer

instrument
B8 connected tachometer plugging element
connected with revolution signal
with negative B12
pole
connect to the cathode of sensor
A7 1
B7 connected
connected with sensor anode with positive
A5 pole
speedometer connected with sensor
2
A11
B14 connected
with positive 3
digital clock pole
fuel gauge connected with sensor 4
A12
back door indicating lamp
B6 5
parking brake indicating lamp
B4
safety airbag indicating lamp
A14 6
B7 low oil pressure indicating lamp
connected B10
with positive engine failure indicating lamp
7
pole B11
four wheel drive indicating lamp
A9 8
generator preheating indicating lamp
B1
fuel alarming indicating lamp
9
A15
accumulator charging indicating lamp
B9 10

75

ABS failure indicating lamp
11
B2
A4 connecting 12
with lighting
switch
irect-current drive power EL 13
A6 connected power supply supply luminous
with negative 5-9V 110V plate 14
pole

15

In this drawing, A stands for the white plugging 16

elements, B for black plugging elements, they
pressure-regulating use the same numerical order.
potential device
BE-34 Body Electric System
Combination Instrument

Electric circuit diagram (continued)

A16 A1 B16 B1

SL SK 4P A9 vehicle speed signal SY SJ accumulator plus four door-closing indicating lamp

A3
turn on when the door is opened.

G A11 odometer sensor _NO

B1 speed and mileage meter V A11 odometer sensor
A10
odometer sensor anode
electronic odometer A10
B11
electronic tachometer sensor signal engine ignition coil

electronic tachometer B11

B16 water thermometer

water thermometer coolant temperature sensor B5
B5 A12
A12 fuel gauge
fuel gauge fuel gauge sensor
neutral gear indicating lamp A9
upper beam upper beam B14
_NP
_NP B14
differential latch-in differential latch-in A2
A2
safety belt vacuum alarming B10
B3 preheating
preheating B9 B3
sediment water alarming B9
sediment water alarming B10
electricity charging/
electricity charging/ discharging A13
discharging A13
fuel level alarming B6
fuel level alarming B6

brake failure alarming lamp A14 brake failure alarming lamp A14
oil pressure alarming lamp A15
oil pressure alarming lamp A15
rear fog lamp B1 rear fog lamp B1
engine failure B2
engine failure
A1 B2 four wheel drive indicating lamp
four wheel drive indicating lamp B15
B15 A1 left turn indicating lamp
A1 Aturn indicating lamp
A16
B16 left turn indicating lamp A16
B16 right turn indicating lamp

A8 B8
A16 A8 B8

instrument lighting
B4 + instrument lighting B7 - system
system B4 + B7 -
 Body Electric System
Combination Instrument BE-35

Common Troubleshooting
a. Such failures as inaccuracy indication, out-operation of indicator, on the fly of large and small summation meters
(mechanical wheel drive excluded) or incomplete liquid crystal display are caused by the interior failures of the
instrument, therefore, these failures, once occur, should be judged according to the instrument interior failures, and
change the combination instrument directly.
b. In case both the large and small summation meter and the indicator of electronic odometer are on the fly, such failures
can be removed by disassembling the speed sensor from the whole vehicle first, then connecting the sensor and
combination instruments as shown in the drawing.

12V

combination instrument

sensor

signal input

Then, open the power supply and run the rotors quickly to observe the indicator variation of odometer.

running the rotors,

the odometer indicator
should be no less than 40Km/
h variation in speed under
otherwise,
common condition when

vÉë
No

change with the good sensor

Yes No
connector for wiring harness
installation of sensor

malfunction of sensor

good combination instruments

Yes No
harness
connector for wiring
panel
failure of instrument
BE-36 Body Electric System
Combination Instrument

c. The inaccuracy display of tachometer is usually caused by the interior failures of tachometer, in such situation,
change the combination directly. As for the good-bad shift or out-operation of tachometer, the failures can be judged
according to the following approaches:
1) Start the vehicle, then check the voltage of signal input of tachometer (wire harness with multi-meter, the
voltage should be 6 V or so.
2) In case there is no signal voltage, check the power supply system of the whole vehicle to remove the failures
in circuit.
3) The plugs of wire harness is only allowed to be inserted in the combination instruments under the condition
that the signal voltage is normal, and the instrument is in normal operation.
4) Where the instrument is in abnormal operation, such trouble is caused by the failure of combination
instruments, in such case, change the combination instrument directly.
d. Troubles of fuel gauge and water thermometer
1) In case the instrument indicator points to the large number after it is powered, disconnect the sensor from the
plugging elements of wire harness before judging such kinds of troubles, if the indicator is still at large number,
it can be make a judgment that the trouble is caused by the interior failure of instrument, in such case, change
the combination instrument directly; if the indicator returns to the small number, according to which it can be
judged that the trouble is caused by the sensor failure, therefore, change the sensor directly.
2) where the instrument indicator stands still, such trouble may be caused by three causes probably, interior failure
of sensor, plugging elements of wire harness or interior failure of instrument; the inspection may be conducted
according to the following approaches: disconnect the plugging elements of wire harness from that of sensor,
grounding the wire at the sensor end; in such condition, the indicator should move upwardly to the largest
number; if such phenomena occurs, it can show the trouble is caused by the interior failure of sensor, in such
case, change the sensor directly; if the instrument indicator is still immobilized after it is powered, it can be
judged that the trouble is caused by the interior failure of instrument under the condition that the wire harness
and plugging elements are normal, in such case, change the combination instrument directly.

Normal indicating range of combination instrument indicator

Speedometer
Real speed Km/h 20 40 60 80 100 120 140 160

Displayed speedKm/h 20
3 4005 6005 8005 10005 12006 14007 16008

Tachometer Dr SL SK SF
Real rotating
speedr/min 1000 2000 3000 4000 5000 6000 7000
Displayed rotating
speedr/min 1000
100 2000
200 3000
150 4000
200 5000
250 6000
300 7000
350

Tachometer SY SL
Real rotating
speedr/min 750 1000 2000 3000 4000 5000 6000
Displayed rotating 750 +20 1000-10+50 2000
120 3000
150 4000
200 5000
250 6000
300
speedr/min -10

Fuel gauge Dr SF SY Fuel gauge SJ Fuel gauge SL SK

Displayed oil Displayed oil Displayed oil
volume E 1/2 F volume E 1/2 F volume E 1/2 F
Reference Reference Reference
110 38 7 110 38 7 120 45 17
resistance
resistance
resistance

Permitted Permitted Permitted
error

5
4 +3 error

12
4
2 error

10
10
10
 Body Electric System
Backup Radar System BE-37

Backup Radar System

Part Mounting Position

Dr SF

back up radar control box

SL SK

rear bumper

right rear wheel

back up radar control box

left rear wheel
BE-38 Body Electric System
Backup Radar System

Inspection on Common Trouble

Trouble description Failure Judgment Methods Repairing and treatment approaches

Vehicle model SL SK
No backup radar display (no Check whether the plugging elements of power supply
system start notification when of back up radar control box are in well connection as
shown in drawing H in next page.(when the reverse
the reverse gear is engaged) gear is engaged, touch the detector, if there is vibration,
which shows the detector is powered.
Check whether the wire harness of inner mirror in
electric room and that on the top of body are in well
connection as shown in the drawing A in next page
Check whether the wire harness of back up radar
control box is well connected with that of chassis
and that on the top of body.
If the voltage fails to reach 12 v, check the power
Rotate the vehicle key to the ACC position and
supply system of original vehicle
s large wires
engage the reverse gear, then measure to see whether
to restore the voltage to 12 V.
the back up power supply reaches to 12 V with the
multi-meter of 50 V of voltage, refer to the
red If the voltage reaches 12 V, change the backup
and black
positions shown in the drawing in next radar control box in trial firstly, then the inner
page. mirror in electric room, finally change the roof
wire harness and the chassis.
No backup radar display (but Check whether the power supply of back up radar
there is start notification when is well located, see the red and position in the Poor properties of ultrasonic wave
the reverse gear is engaged) drawing of next page.
remark: such trouble occur
Check and align the plugging element. Change the ultrasonic detector heads.
under the blocking condition.
Continuous back up radar red Check whether the detectors in the two circuit of
lamp alarming (remark: there back up radar control box is well plugged, see the Check and well connect those plugging elements
marked positions F, G in the drawing of next page.
is no obstacle within 0.5 m away
Check and well connect those plugging elements
from the detector head) Change the ultrasonic detector head
Poor connection of the left/right ultrasonic detector head
Poor performance of back up radar control box. Change the back up radar control box.

Vehicle model pc
Alarming by mistake Conduct the inspection operation for the rear
The rear standby tire is removed
standby tire at the spacious place

fail to detect the obstacle The detector head doesn
t work Change the detector head

fail to detect the obstacle There is dirt on detector head Clean the detector head

Rear standby tire inspection 1. engage the reverse gear for five times repeatedly within ten seconds at the spacious place so that the red
lamp on the screen flash three times, the system will automatically remember the standby tire status.
2. When the body height varies or the stand by tire is opened, make a new inspection for the rear stand by
tire to ensure the backup radar in normal operation.

Seven section of lamp display Column I
1.49m-1.3m Column II
1.29m-1.1m

Column III
1.09m-0.9m Column IV
0.89m-0.75m
Column V
0.74m-0.6m column VI
0.59m-0.45m
Column VII

0.45m
Remark: the right and left LED display the direction and distance of obstacle respectively for driver
reference.
 Body Electric System
Backup Radar System BE-39

Distribution Drawing of Wire Harness

SL SK

inner mirror in electronic room

back up radar control box

F connected with
detector head
G connected with
detector head
red

H black
BE-40 Body Electric System
Wiping and Washing System

Wiping and Washing System

Part Mounting position

front brusher motor brusher and

washer switch
washer motor

rear washer motor SY

rear brusher motor SF

rear brusher motor SY

 Body Electric System
Wiping and Washing System BE-41

Electric circuit diagram of wiping and washing system

Dr SF

3
13
fuse
5 OFF
fuse INT

brusher switch
ACC ON ST LO
HI
ignition switch
washing
6 14 21 20

4 5 2 1

brusher motor

washer motor
M
battery

combined switch

ignition switch brusher motor

7 6 5 4 3 2 1

14 13 12 11 10 9 8 5 4 3 2 1
3 2 1

21 20 19 18 17 16 15 10 9 8 7 6 6 5 4
BE-42 Body Electric System
Wiping and Washing System

Electric circuit diagram of wiping and washing system (continued)

SL SK

fuse 7
2 P
1 2 3 4 5 6 7
2 1 3
grounding MIST
intermission return gear wire

brusher switch
N OFF
power motor
washing returning INT
supply
LO
ACC ON ST 4 6
5
HI
ignition switch
washing
1 6 4 5

1
4 3 2
washer motor

brusher motor
battery

2 5 1

combined switch
ignition switch

1 2 3 4 5 6
4 3 2 1
8 7 6 5 7 U 9 10 11 12

washer motor
rain-brusher intermissive relay brusher motor

1
1 2 3 1 2 3

4 5 6 4 5 6
2
 Body Electric System
Wiping and Washing System BE-43

Electric circuit diagram of front and rear brusher and washing system
SY SJ heating wire
rear defrost relay

fuse
rear defrost switch

1 3
2 Q

rear defrost rear brusher

3 motor
switch
1 0
rear brusher motor
2 1 2 2 1
4
3 4 4 3
8 76 5
OFF
rear brusher rear brusher ignition
ON switch switch switch
4 1 2 3 4 4 3 2 1
5 6 7 8 8 7 6 5
rear washer rear washer front washer
switch rear washer motor motor
1 3 0
motor
2 4 1 2
1 1

2 2
washing

MI OFF INT LO HI
3
7
6 2 0 1
2 5 rain-brusher front brusher
5
4 3 intermissive relay motor
4
7 5
3 4
6 1 2 3 1 2 3
2
1
front brusher 4 5 6 4 5 6
motor
brusher 1
switch
rear washer
switch

1 2
3 6
grounding
return

3 4
wire

1 5 1 0 2
washing
return

2
intermission

4 front washer
supply
power

motor combined switch

rain-brusher intermissive relay 7 6 5 4 3 2
8 1
16 15 14 13 12 11 10 9
small lamp switch
ON OFF
1
combined switch
6
1 2 3 4 5 6
small lamp relay 7 8 9 10 11 12
ONACC
ignition switch
fuse

battery
BE-44 Body Electric System
Wiping and Washing System

Electric circuit diagram of rear window, rear brusher and washing system
SF

5 4 rear brusher motor 5

rear window up-down switch

ACC
ON
ST

M
fuse

7 6

rear washer motor

ignition switch
defrost switch

M
3 1 6 4

15 4 3 2 11 10
7
battery

5 1
9 rear window and rear brusher controller
8
6 5 17 12 14

back door window location switch

defrost indicator light

19 12
back door regulator
defrost power grill

lock switch
back door

rear washer
switch

ignition switch
rear window and rear brusher controller defrost switch

5 4 3 2 1
1 2 3 4 5 6 7 8 1 2 3 4
10 9 8 7 6 9 10 11 12 13 14 15 16 17 18 5 6 7 8 9 10

combined switch
rear brusher motor

7 6 5 4 3 2 1

3 2 1
14 13 12 11 10 9 8

21 20 19 18 17 16 15 6 5 4
 Body Electric System
Wiping and Washing System BE-45

Inspection on Common Trouble

Trouble Possible causes Repairing approaches

Brusher cannot move or cannot Burn out of brusher fuse; Failure of brusher motor;
return to the stop position Failure of brusher switch; Brusher or grounding failure;
Change the fuse and check whether there Check the brusher motor;
is short circuit;
Check the brusher switch. Make reparation as required.

Brusher has no action at the Failure of brusher switch; Failure of motor switch;
intermissive gear Wiper or grounding failure; Check the brusher switch;
Check the wiping motor. Make reparation as required.

Washer has no action The washer hose or nozzle is blocked; Make reparation as required;
Failure of washer motor; Check the washer motor;
Failure of washer switch; Check the brusher switch;
Wiring failure. Make reparation as required.
BE-46 Body Electric System
Wiping and Washing System

Parts inspection
Brusher switch conductance situation

aê
Terminal 6 14 13 21 20
switch position Gr Gr/G Gr/Br Gr/Bl Gr/B

OFF

7 S 5 4 3 2 1
INT
14 13 12 11 10 9 8

21 20 19 18 17 16 15
LO

HI

Washing

pc
Terminal 6 14 13 21 20
switch position Gr/R Gr/G Gr/Br Gr/Bl Gr/B

OFF
7 6 5 4 P 2 1
INT
14 13 NO 11 10 9 8
21 20 19 18 17 16 15
LO

HI

Washing

pi=ph=pv=pg
Terminal 1 2 P 4 5 6 7
switch position W/B Gr/R Gr/Br Gr/Bl Gr/G Gr dêL_ê

MIST

1 2 3 4 5 6 OFF

7 8 9 10 11 12
INT

LO

HI

Washing
 Body Electric System
Wiping and Washing System BE-47

Brusher switch conductance situation (continued)

SLDiesel SYDiesel
Terminal 1 2 3 4 5 6 7
switch position Bl/B Lg/R Lg/W Bl/Y Bl Bl/O Lg/W

MIST

1 2 3 4 5 6
OFF

7 8 9 10 11 12
INT

LO

HI

Washing

In case the conductance situation fails to satisfy the requirements in the above-mentioned drawing, change the switch.

Conductance Situation of Rear Brusher

SY SJ

Terminal 1 8 7 6 5
switch position R/Y B G/W Bl/Y B/Y
4 3 2 1
OFF
8 7 6 5

ON

SYDiesel

Terminal 1 8 7 6 R
switch position R/Y B G/R Bl/Y B/Y
4 3 2 1
OFF
8 7 6 5

ON

Where the conductance fails to satisfy the requirements in the above-mentioned drawing, change the switch.
BE-48 Body Electric System
Wiping and Washing System

In low-speed operation
3 2 1 Check the front brusher motor
6 5 4 Connect the anode lead to the terminal 2 (1) from accumulator, and
the cathode lead to terminal 3, at this time, the front wiper motor
should be in low-speed operation, otherwise change the front
brusher motor.

In high-speed operation
3 2 1 Connect the anode lead to the terminal 1(2) from the accumulator,
6 5 4
and cathode lead to terminal 3, in such condition, the front wiper
motor should be in high-speed operation.
In case the operation fails to meet the requirement, change the front
wiper motor.

in operation
stop running at the stop position

3 2 1 a. Run the front wiper motor at low speed and stop it at any
6 5 4
positions excluding the stop position by disconnect the
anode lead from the terminal 2 (1).

b. Connect the terminals 2 and 5.\

3 2 1 c. Connect the anode lead to the terminal 6 (4) from the
6 5 4 accumulator, and the cathode lead to terminal 3, check
whether the wiper motor parks at the stop position after
it running for another time, if the requirement is not
satisfied, change the front brusher motor.
Remark: items in parenthesis is for Dr and SF.

Rear brusher motor inspection

2 1 Connect the anode lead to the terminal 3 from the accumulator, and
4 3 the cathode lead to terminal 4, at this time, the wiper motor will be
in normal operation, disconnect the terminal 3, the rear wiper motor
should stop running at any position excluding the stop position.
 Body Electric System
Wiping and Washing System BE-49

Connect the anode lead to terminal 3 from the accumulator, and

2 1 cathode lead with terminal 4, at this time, the wiper motor should
4 3 be in normal operation, under such condition, disconnect the
terminal 3, which is connected with terminal 1, and the anode lead
is connected to the terminal 2, in such case, the rear wiper motor
should stop running at the stop position.
In case the operation fails to satisfy the specified requirement,
change the rear wiper motor.

Inspection on Washer Motor

Connect the anode lead to the terminal 1 from the accumulator, and
1 the cathode lead to the terminal 2, at this time the washer motor
2 should be in normal operation.
Notice: this test should be finished rapidly (within 20 seconds).
In case the operation fails to meet the specified requirement, change
the washer motor.
BE-50 Body Electric System
Central Control Lock and Electric Rocker Gear System

Central control lock and electric rocker gear system

Part Mounting position
Dr SF

Central control lock box

SL SK SY SJ

Central control lock box

 Body Electric System
Central Control Lock and Electric Rocker Gear System BE-51

Electric circuit diagram of central control lock

aê left front door switch

fuse

main lock
left front
1
6

controller box
central
5

main lock
right front
3
4

auxiliary lock
left rear
battery

auxiliary lock
right rear
control case of central control lock

8 7 6 5 4 3 2 1

pc

fuse 1

8 12
to generator
power lead
3
M
central controller box

to left turn 6
lamp 2

to right turn
5
lamp M
four doors locker

to door 7
lamp switch
11 M
10
switch at left front door
central control lock
battery

lock-head lamp

M
13

control case of central control lock

6 5 4 3 2 1

13 12 a 10 9 8 7
BE-52 Body Electric System
Central Control Lock and Electric Rocker Gear System

Definition for connecting wire of central control lock

SF Remark: the inner switch in actuator should be
connected when the actuator is in the locking status
Remark: In case the actuator is in locking status,
Power anode 12 V connect the switch inside.
1
unlocking signal of central control lock
2
locking signal of central control lock M K
3
no signal
4
right turn lamp
5
left turn lamp
6
13P negative input of door switch
7
ON power check cable ON wire connected to key NOs
8
no connection j

9 h
lock head lamp
10
unlocking signal
11 h
locking signal left front CCL switch
12
power cathode
13
6 5 4 3 2 1
13 12 11 10 9 8 7

1. Y/V Connect the power to the cell anode on vehicle, in front of which a fuse of 15 A should be set, and
anode of 12V when the motor is started, the voltage should not less than 10V
2. B1 Unlocking output of the locking wire of the CCL actuator, and the grounding wire at the normally
central control lock: closed contact inside the relay will contact with the normally opening contact at
the common spots inside relay when unlocking with REMOTE CONTROLLER
or manually, the wire will output 12 V voltage.
3. LG locking signal of The CCL locking signal is connected to the unlocking wire of actuator of CCL,
central control lock and the normally closed contact in the interior relay is grounding wire, which will
output 12 V voltage when unlocking with REMOTE CONTROLLER or manually
and the common spots of relay contacting the normally opening contact.
4. non-connection There is no wire connected at present
5. G/R Right turn lamp Connected to the anode wire of the right turn lamp on the vehicle, and it will output
12 V voltage in operation.
6. G/Y Left turn lamp Connected to the anode wire of left turn lamp on the vehicle, and it will output
12 V voltage when in operation
7. Br Negative input of Which is connected to the door switch and it is grounding when the door is
door switch opened (the indoor lamp will light)
8. GD ON power check cable Connected to the ON wire of the locking door( there will be 12 v voltage when
rotating the key at
ON
position.
9. Non-connection This wire is not connected temporarily
10. GD/B Lock head lamp output There will be 12 V voltage outputted in this wire when opening the door, and will
be powered off (no output) ten seconds later after the door is closed
12. Y/B Locking signal Connected to the locking signal wire of CCL at the left front door, and connect
to the grounding wire when in operation.
13. B Power cathode Connect to the body (grounding wire) it should be as short as possible, because
the overlong wire will produce the interference source.
 Body Electric System
Central Control Lock and Electric Rocker Gear System BE-53

Electric circuit diagram of central control lock (continued)

SL SK
fuse
8
6
5

controller box
central
battery

4
3

7 left front door right front door left rear door right rear door
main lock main lock auxiliary lock auxiliary lock

control case of central control lock

1 2 3 4 5 6 7 8

pv
turn lamp

fuse

ignition switch
11
1

1 10 6
controller box
central

9
4
ACC ON ST 8
5

12 7
speed sensor

door lamp switch

battery

left front main right front left rear right rear

lock main lock auxiliary lock auxiliary lock

control case of central control lock

ignition switch
1 2 3 4 5
4 3 2 1
8 7 6 5 6 7 8 9 10 11 12
BE-54 Body Electric System
CCL and Electric Rocker Gear System

Electric circuit diagram of CCL

SJ Top-grade SY

left front electric rocker gear switch

turn lamp

fuse

ignition switch
11
1

N 10 6
9 central controller 2
ACC ON ST
8 box
5

12 7
speed sensor

door lamp switch

battery

left front main lock right front main left rear auxiliary right rear auxiliary
lock lock lock

central controller box

ignition switch
1 2 3 4 5
4 3 2 1
8 7 6 5 6 7 8 9 10 11 12
 Body Electric System
CCL and Electric Rocker Gear System BE-55

Definition of the connecting wire of CCL

SY SJ

6 1 left turning light

manual switch locking signal

closing window output
7 2
none
8 3
door switch negative input
K
9 speed test 12V door switch
W M M M M
K
10 ACC test
power anode 12V
remote control opening lock output
11 4
power cathode
remote control closing lock output
12 5

1. G/R (G/W) Turn lamp Connected to the anode wire of the turn lamp (right ) on vehicle, it will output 12 V voltage
when it is in operation
2. O
w/b1) Window-shutting signal output This wire has one second of voltage output of 12V when the car door is locking. (top SY SJ)
3. No connection
4. G (Y) Unlocking output of CCL Connected to the locking wire of actuator of CCL, and the normally closed contact in the
internal relay is the grounding wire.It will output 12 v voltage when locking with REMOTE
CONTROLLER or manually because the common spot of relay will contact the normally
opening contact.
5. Bl (G) Locking output of CCL Connected to the locking wire of actuator of CCL, and the normally closed contact inside
the internal relay is the grounding wire.It will output 12 V voltage when locking with
REMOTE CONTROLLER or manually because the common sots of relay will contact
with the normally opening contact.
6. Gr (G/B) Turn lamp Connected to the anode wire of left turn lamp of vehicle, it will output 12 v Voltage when in
operation.
7. W (W) Manually controlled unlocking signal The door lock control the locking process through the manual unlocking switch at left front
door, that is, under the locking condition, press the switch, the lock will be opened (the
switch will return to the connection situation automatically after pressing.
8. Br (R/B) Negative output of door switch Connected to the car door lamp switch, it is connected to the grounding wire (the indoor
lamp will light when opening the door.
9. R/G (G/B) Rotating speed test The car door will lock automatically when the vehicle reaches a certain speed.
10. W(R ) ACC test Connect to the ACC wire, which will have 12 V voltage when the key is rotated to the ACC position.
11. R (R ) Power anode (12V) Connect to the anode of accumulator on vehicle, in front of which should be set the fuse
so that the voltage will be no less than 10V when the starter is in operation.
12. B(B) Power cathode Connect to the body (grounding wire), it should be short as possible as can because the
overlong wire will produce the interference source.
Items in the parenthesis is for SY diesel model
Items with
are configuration for SJ and top SY
BE-56 Body Electric System
CCL and Electric Rocker Gear System

Diagram of electric rocker gear

Dr

2 2 1 1
falling

auxiliary stop

raising

4 3
5 right rear
2 1
falling

main stop

raising

left rear door switch

3 4 5 main auxiliary

2 2 1 1 1 2 1 2
falling

auxiliary stop
3 4 5 3 4 5
raising

4 3 left rear
R
2 N
left rear door switch

falling main auxiliary

main stop
1 2 1 2
raising
3 4 5
3 4 5 3 4 5
1 2 1 2
falling
right front door switch

auxiliary stop

raising
main auxiliary
4 5 1 2 1 2
3 right front
1 2
falling
main stop 3 4 5 3 4 5
raising

3 4 5
inhibitor switch

1 2 1 2
falling
stop
left
left front door switch

electric rocker gear

raising front
1 2
3 4 5 1
3 4 5
2

electric window relay

fuse

ST ON ACC
ignition switch

ignition switch

5 4 3 2 1

10 9 8 7 6
battery
 Body Electric System
CCL and Electric Rocker Gear System BE-57

Diagram of electric rocker gear

SF

2 1
5 2

right rear

1
3 4

2 1
2 5

left rear

1
3 4
right rear door switch

2 1 1 2
5 2

3 4 5
right
front
left rear door switch
1
3 4
1 2

3 4 5

2 1
12 7
inhibitor switch

right front door switch

left 1 2
front
3 4 5
1 13 3 4 2
control lock
12
11 left front door switch

1 2 3 4 5 6

7 8 9 10 11 12 13
electric window relay

ST ON ACC ignition switch electric rocker gear

5 4 3 2 1 1
ignition switch
fuse

2
10 9 U 7 6
battery
BE-58 Body Electric System
CCL and Electric Rocker Gear System

Diagram of electric rocker gear

SL SK SY

1 2 1 5
falling

auxiliary stop

raising

3 4 right rear
2
1 5
falling main auxiliary
main stop
1 1

left rear door switch

raising

2 3 4 2 2
3 3
1 2 1 5
4 4
auxiliary

falling
stop 5 5
raising

3 4 left rear main auxiliary

2
1 5
falling left rear door switch 1 1
main stop
2 2
raising

2 3 4 3 3
4 4
1 2 1 5 5 5
falling
auxiliary

stop

raising
main auxiliary
3 4
2 5 right front
right front door switch

1 1 1
falling
2 2
main stop
raising 3 3
2 3 4 4 4
5 5
inhibitor switch

5 2 1 1
falling
stop left front
raising

2 3 4
electric rocker gear
left front door switch

N
1
2
3 2
4
electric window relay 5
fuse

ST ON ACC
ignition switch

ignition switch

Q P O N

U T S R
battery
 Body Electric System
CCL and Electric Rocker Gear System BE-59

Diagram of electric rocker gear

SJ Top-grade SY

4 2 1 3

right rear

5 1 6 2

electric rocker gear 1

2 1 2
4 3

left rear right rear door switch

5 1 6
1 2

3 4 5 6

Q 2 1 3

left rear door switch

right front
1 2
5 1 6
3 4 5 6

2 1
8 5 Q
right front door switch
iocking switch

1 2
left front

3 4 5 6
3 1 6 10

central control lock

ST ON ACC left front door switch

ignition switch

1 2 3 4

5 6 7 8 9 10
fuse
battery
BE-60 Body Electric System
CCL and Electric rocker Gear System

Inspection on Common Trouble

Trouble Possible causes Repairing approaches

Electric rocker gears at four Burned out fuse Change and check whether there is
doors don
t work short circuit

The CCL at four doors don
t work Burned out fuse Change and check whether there is
short circuit

The electric rocker gear or Wiring failure Make reparation as required.

CCL at one Seize-up of electric rocker gear Make reparation as required.
door doesn
t work or mechanical lock
Failure of brush-rocker or lock Change
out device

The indicating lamp of electric rocker gear Wiring failure Make reparation as required.
switch doesn
t work Failure of indicating lamp locates Change
interior side of switch

One remote controller cannot c There is no electricity in the Change the cell
ontrol the CCL remote controller

Both remote controller cannot Controller box damage Change

control the CCL
Glass cannot raise automatically after the Wiring failure Make reparation as required.
car door is locked (top SY SJ) Failure of Control case of CCL Change
Brush-rocker switch failure Change
 Body Electric System
Acoustical Equipment System BE-61

Acoustical equipment system

The devices in this series is the vehicle-equipped acoustical receiver and recorder whose function is realized through
the electronic tuner and CD recorder, therefore, it can receive the amplitude modulation, frequency modulation and
stereo broadcast and can record the CD disc, what??s more, it is with the advanced electric anti-quaking, strong capability
of error correction, fashionable blue LCD liquid crystal digital display, and four-way power output. The device in this
series also has the characteristics such as low distortion, large output power and good performance of anti-interference,
broad frequency range and sweet sound, etc.

Diagram of Acoustical equipment system

SF

fuse

from small lamp relay

loudspeaker
5 4

left front right front left rear right rear

6 2 5 3
cigarette lighter

ACC ON ST 8

ignition switch 4
9

1 2
side-window aerial
5
amplifier
7 CD device
battery

1
7 3

plugging elements of rear

ignition switch CD plugging element loudspeaker of CD device

5 4 3 2 1 1 2 3 4 1 2

10 9 8 7 6 5 6 7 8 9 3 4 5

Note: For Dr the antenna is the rod type.

BE-62 Body Electric System
Acoustical Equipment System

Diagram of acoustical equipment system (continued)

SL SK

fuse

ignition switch
fuse
1

small lamp relay

4 6 2 5
ACC ON ST

receiver
9 PQ 8 1 3O 5 7
6
battery

small lamp

large lamp

receiver receiver ignition switch

1 2 3 4 1 2 4 3 2 1
5 6 7 8 9 3 4 5 8 7 6 5

combined switch
7 6 5 4 3 2
8 1
16 15 14 NP 12 11 10 9

SY SJ

fuse

ignition switch fuse

1
small lamp relay

6 2 5
electric aerial

CD device

ACC ON ST 4
1

9 34 8 1 32 5 7
6
battery

small lamp

large lamp

CD device CD device ignition switch

1 2 3 4 1 2 4 3 2 1
5 6 7 U 9 3 4 5 8 7 6 R
combined switch
7 6 5 4 3 2
8 N
16 NR 14 13 12 11 10 9
 Body Electric System
Acoustical Equipment System BE-63

Inspection on Common Trouble

Trouble Possible causes Repairing approaches Page
Receiver Lack of power supply Burned out fuse Change the fuse and check whether there is
CD recorder short circuit;
Wiring failure Make reparation as required
Loudspeaker doesn
t work Faalure of loudspeaker Chaange the loudspeaker;
Wiring failure Make reparation as required.
Do not read the tape or disc Receiver failure or Change the receiver or CD recorder
CD recorder failure
AM or FM doesn
t work Receiver or CD recorder failure Change the receiver or CD recorder
VCD Non-opening of devices Aerial failure Change or repair it as required; BE-64
Wiring failure Make reparation as required.
Main machine failure Change the main device
Neither image nor sound is Failure of main device; Make inspection as required and change BE-64
broadcasted converter box failure plus disc box the parts with failure
failure
No image when backing up Wiring failure Conduct an inspection as required and BE-64
Failure of video camera change the parts with failure
FM/TV failure Failure of aerial amplifier Make an inspection as required and change BE-65
Weak signal from TV station the parts with failure
Screen cannot be turned over Unsuitable main device adjustment Adjust according to the application BE-65
Failure of main device instruction;change the main device
Disc box cannot be pushed Failure of disc box Make an inspection as required
outside
Bass speaker doesn
t work Wiring failure Make reparation as required.
Failure of bass speaker Change the bass speaker.
Electric Non-raising when receiver is Wiring failure Make reparation as required.
aerial opened Failure of electric aerial Change the electric aerial
Falling seize-up Wiring failure Make an inspection as required and change
Failure of electric aerial. the parts with failure.
BE-64 Body Electric System
Acoustical Equipment System

Inspection on Common Trouble

(a) Main engine cannot be opened

Check whether the voltage of Check the fuse in power wire

Ther is no action when pressing k
ACC and storage cell reaches or the power supply of the
the
ower
key repeatedly
12 V entire vehicle

Failure of main
engine

(b) No voice or image when broadcasting

NO CDC
displayed on k Check whether there is image k Failure of main

Re-open the device
screen when backing up engine

v
OFF
Be normal after Check the converter box works
Failure of converter
returning normally (whether the lamp is
box
light or not)

ON

Failure of disc box

(c) There is no image when backing up

There is no image in Whether the screen display black screen Failure of video
video camera is blue screen camera

blue screen

The backing up wire is not connected

well; reconnect it to the positive polar
of 12V of reverse gear
 Body Electric System
Acoustical Equipment System BE-65

(d) FM/TV failures

FM receiving effection is Whether the signal of local TV v Pay attention to the

not good station is weak receiving location

Check whether the aerial

interface peels off

The receiving effection of Whether the signal of local v Pay attention to the
TV station is bad TV station is weak receiving location

Check whether amplifier works OFF Turn the amplifier switch to

normally (the lamp is lighting )
ON
position

ON OFF

Search the TV station for

Amplifier failure
another time

(e) disc box cannot be sent out

Invalid Move the small window

Disc box cannot be sent out Press
OPEN
key shrapnel at bottom of disc box
then it can be sent out

Invalid

Failure of disc box

BE-66 Body Electric System
Acoustical Equipment System

Mount of bass speaker and VCD

(a) bass speaker
Connect the audio output wires of bass speaker with the sockets in bass speaker correspondingly according
to the wire color (red plugging element should be plugged in red socket, yellow plugging element in white
socket, the grounding wire (black), power wire (yellow) and signal wire (blue) should be fixed at the
corresponding positions (GND
12V
REM) on bass speaker tightly.
(b) multi-disc VCD
The feed cables of VCD main device should be connected as marked, when connecting the plugging element
of wire harness of video camera (CAM) with the plugs on main device (CAM), notice should be taken on the
two arrow marks so as to prevent the plugging element damage; The audio output wire plugging elements (red
and yellow plugs) of bass speaker should be connected with the red and white sockets of mainframe (AV OUT);
the plugging elements of TV receiving input wire of amplifier should be connected with either of the plugging
elements(AV AN) of the mainframe; the plugging element (black and white ACC) of anode wire of power
supply should be connected with the red socket (ACC) of mainframe wire harness; grounding wire plugging
element (black GND) should connect with the black socket of mainframe wire harness; the plugs of audio input
wire of deci-disc data converter should be connected with the red and white socket on mainframe according
to the plugs color (the plugs (red, white CD OUT) of audio input wire of eight-disc box should be connected
with the red, white socket (CD IN) on mainframe according to the plug color, the yellow power wire plugging
element (BATT) should be connected with the yellow power wire socket (BATT) on mainframe, the electric
aerial, plugging elements of control wire of function amplifier should be connected with the electric aerial
(CTL), socket of control line of function amplifier on mainframe. After completing the connection of plugging
elements, wrap the connecting position with adhesive strap in order to prevent those plugging elements from
peeling off, the plugging element of feed cable of TV receiving aerial can connect with any two of the four
holes on amplifier, meanwhile, turn on the switch (with a red indicating lamp) of amplifier when watching the
TV play. When mounting the VCD mainframe, push the wire harness innermost as can as possible so that there
is spacious room for mainframe, then push in the mainframe, notice should be taken not to damage the wire
harness. Fasten the mainframe to the degree that it cannot be pull out by hand after assembling, if it cannot be
clamped tightly, prize out the two clips on the inner sleeve, then fasten the mainframe, and mount on the
external decoration frame finally. When disassembling the mainframe, tear down the external decoration
frame first, then insert the special key into the open grooves at two sides to pull out the mainframe.
 Body Electric System
Acoustical Equipment System BE-67

Connecting Sketch of VCD System

SY SJ

ACC BATT
grounding
back up signal

right rear

left front
right front

left rear
Bl B R Y Gr/B Gr V/B V W/B W G/B G

Notice: Y
video
R
right sound
1. The aerial control should be track
W
left sound
highly effective; track

2. The control of function amplifier VCD output

should be highly effective;

3. The disc device should be
earthed fixedly
grounding wire
connecting wire of disc box
screen

disc box
RCD/AUDIOOUT/R
WCD/AUDIOOUT/L

ACC

RADIO ANTENNA IN
BL aerial control
W audio output

R audio output

YD function amplifier control

radar input

camera input

TV aerial input
RCD audio input

RCD audio input

RAV audio input

Y video input
RAV audio input

L R L R L R
BE-68 Body Electric System
Wire Harness Distribution

Wire harness distribution

Housing wire harness
aê

1
7
8 6 5 2
V P
10 4 11
12

13 21

14
17
NR 16

18
20
19

1 back-up lamp switch 11 air-conditioner compressor12water temperature sensor

2 starter 13 washer motor
3 starter 14 right headlamp
4 oil pressure sensor 15 right lever-shaped lamp
5 grounding wire 16 electric horn
6 grounding wire 17 generator
7 connected to protective box II 18 left headlamp
8 protective box II 19 left lever-shaped lamp
9 connected to protective box II 20 front turn lamp of left side
10 starter 21 connected to protective box I
 Body Electric System
Wire Harness Distribution BE-69

Housing wire harness (continued)

SL SK SY SJ

O
30 31
3 29
28
4
5
6
8 7
10 9
27
26
24 25
23

11
12
13
14
15 16 17

18
19
22
20 21

1 connected to cab wire harness 17 horn electric horn

2 connected to cab wire harness 18 left turn lamp
3 odometer sensor 19 left small lamp
4 back-up lamp switch 20 left headlamp
5 turn lamp on right side 21 left fog lamp
6 grounding wire 22 pressure switch of air-conditioner
7 brush motor 23 generator
8 protective box II 24 generator
9 wire connecting with accumulator anode 25 grounding wire
10 wire connecting with accumulator anode 26 turn lamp on left side
11 electromagnetic fan 27 brake liquid level sensor
12 washer motor 28 connected to cab wire harness
13 right fog lamp 29 connected to cab wire harness
14 right turn lamp 30 connected to cab wire harness
15 right headlamp 31 flasher relay
16 right small lamp
BE-70 Body Electric System
Wire Harness Distribution

Housing wire harness (continued)

SF

19 18
2017 161413 12 59
15 11 10
9 6 5
87 4 P2 1
22
21 27 28
2930 31 32
26 33
23 2425 34 36
37
61 35 38
47 39
48
40 60
42 41
51
50
49
52
58
53 54
57
55 56
46 45
43

44

1 left door lamp switch 22 electric fan relay 43 left front conner lamp
2 defrost switch at tail door 23 maxi-fuse 44 left front lever-shaped lamp
3 window regulator at tail door 24 joint of wire harness at right front door 45 front fog lamp
4 parking brake switch 25 right front door lamp switch 46 left headlamp
5 ignition lock 26 right electric back-up mirror 47 temperature control switch
6 combined switch 27 grounding wire 48 connected to wire of 220
7 instrument 28 rear sound box wire 49 spraying motor A
8 combined switch shell 29 ashtray lamp 50 spraying motor B
9 grounding wire 30 CD Device wire 51 right front conner lamp
10 amplifying plate of air-conditioner 31 cigarette lighter A 52 right headlamp
11 heat-sensitive resistance 32 cigarette lighter B 53 horn A
12 control panel of air-conditioner 33 dual flasher switch 54 horn B
13 A/C Switch 34 fog lamp switch 55 right front lever-shaped lamp
14 glove-box lamp switch 35 temperature indicator 56 right front fog lamp
15 glove-box lamp 36 stop lamp switch 57 electric fan
16 speed-adjusting resistance 37 brake liquid level sensor 58 outdoor temperature sensor
17 blower 38 control case of central control lock 59 connected to chassis wire harness
18 indoor temperature sensor 39 left front loudspeaker anright central wire harness
19 right front loudspeaker 40 automatic aerial 60 connected to left central wire harness
20 brush motor 41 turn lamp on left side 61 connected to engine wire harness
21 turn lamp on right side 42 generator
 Body Electric System
Wire Harness Distribution BE-71

Cab wire harness

aê

59
60
53 61
54 55
13 62
12
14 56

11 16 15
17 22
10 23 33
18
25 32 34
26 39 40
19
20 21 24 43 45 58
6 47 48 57
9 27 31
28
35
7 8 29 30 36 37 38
1
41 42 44 46 52
50
2 4 49 51
3 5

1 right front turn lamp 22 speed-adjusting resistance 43 parking brake switch

2 outdoor temperature sensor 23 air blower 44 brake switch
3 right lever-shaped lamp 24 grounding wire 45 left loudspeaker
4 front fog lamp 25 A/C switch 46 control case of central control lock
5 horn 26 controlling element 47 grounding wire
6 accumulator wire of 220V 27 ashtray lamp 48 grounding wire
7 electromagnetic fan 28 receiver wire 49 voltage regulator
8 temperature control switch 29 cigarette lighter 50 brake liquid level alarming device
9 protective box II 30 cigarette lighter 51 protective box I
10 turn signal lamp on right side 31 rear sound box wire 52 plug of wire harness at left rear door
11 brush motor 32 amplifying plate of air-conditioner 53 door lamp
12 plug of engine wire harness 33 grounding wire 54 door lamp switch
13 wire harness at right rear door 34 heat-sensitive resistance 55 ceiling lamp
14 plug of frame wire harness 35 dual flasher switch 56 lamp for reading
15 door lamp switch 36 fog lamp switch 57 door lamp
16 wire harness at right front door 37 temperature indicator 58 door lamp switch
17 door lamp 38 combined switch shell lamp 59 backup radar screen
18 right external electric rear vision mirror 39 combined switch 60 right rear loudspeaker
19 protective box III 40 ignition switch 61 highly-mounted stop lamp
20 indoor temperature sensor 41 combination instrument A 62 left rear loudspeaker
21 right loudspeaker 42 combination instrument B
BE-72 Body Electric System
Wire Harness Distribution

Cab Wire harness (continued)

pi=ph

12 38
3
410 11 39
5
6 12 37
7 1617 40
18 19
14 20
8 21 13
15
9 22 23
24
25
26 30
31 36
27 32
33 35
28
29
34

1 grounding wire 21 luminous lamp on air-conditioner panel

2 wire harness at right front door 22 combined switch
3 warm air motor 23 instrument
4 wire harness at right front door 24 instrument
5 control case of central control lock 25 stop lamp switch
6 heat-sensitive resistance 26 connected to roof wire harness
7 speed-adjusting resistance 27 connected to housing wire harness
8 connected to housing wire harness 28 connected to housing wire harness
9 connected to housing wire harness 29 connected to housing wire harness
10 A/C switch 30 connected to wire harness at left front door
11 air-volume switch 31 connected to wire harness at left front door
12 ashtray luminous lamp 32 connected to wire harness at left front door
13 ECU 33 protective box I
14 receiver 34 grounding wire
15 rear loudspeaker 35 wire harness at left front door
16 cigarette lighter 36 connected to wire harness at left rear door
17 cigarette lighter grounding wire 37 parking brake switch
18 cigarette lighter luminous lamp 38 connected to wire harness at right rear door
19 fog lamp switch 39 right front door lamp switch
20 dual flasher switch 40 connected to chassis wire harness
 Body Electric System
Wire Harness Distribution BE-73

Cab wire harness (continued)

SY SJ

1 2 11 12 13
3 14
4 1519
18
5 20 51
6 7 46
8 16 2324 25 29 45
17 22 26 47 50
21 27 30
28 43 44
9
10 34
31 35
32 33
36
37 42
38 41 48 49
39

40

1 grounding wire 27 combination instrument

2 wire harness at right front door 28 combination instrument
3 warm air motor 29 stop lamp switch
4 connected to wire harness at right front door 30 roof wire harness
5 control case of central control lock 31 connected to housing wire harness
6 electric aerial 32 connected to housing wire harness
7 heat-sensitive resistance 33 connected to housing wire harness
8 speed-adjusting resistance 34 connected to wire harness at left front door
9 connected to housing wire harness 35 connected to wire harness at left front door
10 connected to housing wire harness 36 connected to wire harness at left front door
11 A/C switch 37 protective box
12 air-volume switch 38 rear defrost relay
13 ashtray luminous lamp 39 connected to wire harness of rear air-conditioner
14 grounding wire 40 grounding wire
15 ECU 41 parking brake switch
16 CD device 42 connected to chassis wire harness
17 CD device 43 wire harness at right rear door
18 cigarette lighter 44 right front door lamp switch
19 cigarette lighter grounding wire 45 right rear loudspeaker
20 cigarette lighter luminous lamp 46 rear washer motor
21 combined switch 47 connected to wire harness at tail door
22 fog lamp switch 48 left front door lamp switch
23 dual flasher switch 49 wire harness at left rear door
24 rear defroster switch 50 left rear loudspeaker
25 rear brush switch 51 standby power seat
26 rear washer switch
BE-74 Body Electric System
Wire Harness Distribution

Cab Wire harness (continued)

SF

9
10
11

14

15 12
13 8
17 7
18 16
5 6

19
3 4
2

20

1 connected to cab wire harness 11 rear brusher motor

2 left rear door lamp switch 12 right rear combination lamp
3 door lamp at left rear door 13 right rear sound box
4 electric rocker and lock-out device at left rear door 14 front ceiling lamp
5 left rear sound box 15 lamp for reading
6 controller for brush, door and window at rear door 16 electric rocker and lock-out device at right rear door
7 connected to wire harness at tail door 17 right rear door lamp
8 left rear combination lamp 18 right rear door lamp switch
9 highly-mounted stop lamp 19 connected to cab wire harness
10 rear ceiling lamp 20 connected to protective box I
 Body Electric System
Wire Harness Distribution BE-75

Wire harness at four door

Dr

Wire harness at right rear door

22 23
19
24
20 21
28
30
31
27 Wire harness at left rear door
OS 25 29 32
16 17
13 18
Wire harness at right front door

14 15
2 7 8
5 6 9
4 10 11

12
1
P
Wire harness at leftfront door

1 connected to cab wire harness 18 lock-out device at left rear door

2 left external electric rear vision mirror 19 right rear door lamp
3 electric rocker 20 connected to wire harness at right rear door
4 rear vision mirror switch 21 right rear door lamp switch
5 power switch 22 right rear door switch
6 romote control lock switch 23 electric rocker
7 rocker switch 24 lock-out device at right rear door
8 rocker switch 25 right front door lamp switch
9 rocker switch 26 connected to cab wire harness
10 rocker switch 27 connected to cab wire harness
11 lock-out device at left front door 28 right external electric rear vision mirror
12 left front door lamp 29 electric rocker
13 left rear door lamp 30 rocker switch
14 connected to wire harness a left rear door 31 lock-out device at right front door
15 left rear door lamp switch 32 right front door lamp
16 left rear door switch
17 electric rocker
BE-76 Body Electric System
Wire Harness Distribution

Wire harness at four doors and body roof

SL SK

wire harness at 18
right rear door

19
25
20 roof wire harness

29 28 27 26

17
30
36
33
35 32 31
2423 22
34
16
wire harness at left
wire harness at right front door rear door

9 13 15
8 10 12 14
7
11
wire harness at left
21 front door
1 4
6
2
3 5

1 connected to cab wire harness 19 right rear door lamp switch

2 connected to cab wire harness 20 ceiling lamp
3 connected to cab wire harness 21 connected to cab wire harness
4 left front loudspeaker 22 lamp for reading
5 left door lamp 23 car door display
6 electric rocker 24 temperature display
7 rocker switch 25 rocker switch
8 rocker switch 26 right rear lock-out device
9 rocker switch 27 electric rocker
10 rocker switch 28 right rear loudspeaker
11 left front lock-out device 29 connected to cab wire harness
12 connected to cab wire harness 30 rocker switch
13 left rear loudspeaker 31 right front lock-out device
14 electric rocker 32 electric rocker
15 left rear lock-out device 33 right front loudspeaker
16 rocker switch 34 right door lamp
17 left rear door lamp switch 35 connected to cab wire harness
18 highly-mounted stop lamp 36 connected to cab wire harness
 Body Electric System
Wire Harness Distribution BE-77

Wire harness at four doors and body roof (continued)

SY
32
wire harness at right front door
26
27
25 28
29
30 31

20
21
23 24 roof wire harness
22
19

NM
1211 18
4 13 15
1 14 V
2 16
5 17
3
6 8
7

wire harness at left rear door

wire harness at left front door

Wire harness at right rear door is distributed in the same way as that at left front rear door.

1 connected to cab wire harness 17 left rear lock-out device

2 connected to cab wire harness 18 rocker switch
3 connected to cab wire harness 19 highly-mounted stop lamp
4 left external electric rear vision mirror 20 rear ceiling lamp
5 left front loudspeaker 21 front ceiling lamp
6 left door lamp 22 lamp for reading
7 electric rocker 23 car door display
8 left front lock-out device 24 temperature display
9 rear vision mirror switch 25 connected to cab wire harness
10 rocker switch 26 connected to cab wire harness
11 rocker switch 27 right external electric rear vision mirror
12 rocker switch 28 right front loudspeaker
13 rocker switch 29 right door lamp
14 inhibitor switch 30 electric rocker
15 connected to cab wire harness 31 right front lock-out device
16 electric rocker 32 rocker switch
BE-78 Body Electric System
Wire Harness Distribution

Wire harness at four doors and body roof (continued)

Top style SY SJ

29
22
23 wire harness at right front door
24
25
27 28
26

17
20 19 16
21 18
roof wire harness

15

10 14
4 11
1 9
2
3 5 12 13

8
6 7

wire harness at left rear door

wire harness at left front door

Wire harness at right rear door is distributed in the same way as that at left rear door.

1 connected to cab wire harness 16 bass speaker(top SY)

2 connected to cab wire harness 17 ceiling lamp
3 connected to cab wire harness 18 grounding wire(top SY)
4 left external electric rear vision mirror 19 lamp for reading
5 left front loudspeaker 20 car door display
6 left door lamp 21 temperature display
7 electric rocker 22 connected to cab wire harness
8 left front lock-out device 23 connected to cab wire harness
9 rear vision mirror switch 24 right external electric rear vision mirror
10 rocker switch 25 right front loudspeaker
11 connect to cab wire harness 26 right door lamp
12 electric rocker 27 electric rocker
13 left rear lock-out device 28 right front lock-out device
14 rocker switch 29 rocker switch
15 highly-mounted stop lamp
 Body Electric System
Wire Harness Distribution BE-79

Wire harness of four doors(continued)

SF

11
10

9
5 6
3 4 8 7

2
1

wire harness at rear door

wire harness at front door

Wire harness distribution at front left door, front right door, rear left door and rear right door are same with each other.

1 connected to protective box I 7 lock-out device at front door

2 connected to protective box I 8 wire harness at central part
3 rear vision mirror 9 wire harness at central part
4 front door-lamp switch 10 rocker at rear door
5 rocker switch 11 rocker switch
6 rocker at front door
BE-80 Body Electric System
Wire Harness Distribution

Wire harness at tail door and of rear air-conditioner

SY SJ

wire harness
of rear brush

13
12

11
10 V
NQ

5 6
7
1 8
wire harness of rear
air-conditioner

2
4
3

Only the vehicle with SY model has the wire harness of rear air-conditioner shown in above-mentioned wire harness.

1 rear A/C switch 8 speed-adjusting resistance

2 connected to cab wire harness 9 license lamp
3 rear air-conditioning relay 10 license lamp
4 grounding wire 11 rear brusher motor
5 temperature control switch 12 defroster
6 electromagnetic valve 13 defroster
7 temperature controller 14 connected to cab wire harness
 Body Electric System
Wire Harness Distribution BE-81

Wire harness at tail door (continued)

SF

1 2

4
5 7
9
6 10
8
12
11

1 connected to left rear wire harness 7 electric rocker at tail door

2 connected to left rear wire harness 8 right license lamp
3 lock switch at left tail door 9 lower limit switch at tail door
4 electro-heating gate at tail door 10 alarming switch at tail door
5 electro-heating gate at tail door 11 lock barrel at tail door
6 left license lamp 12 lock switch at right tail door
BE-82 Body Electric System
Wire Harness Distribution

Chassis Wire Harness

Dr

2
1

8
7
6

5
3 4

9 10
11
12

1 connected to cab wire harness 7 left license lamp

2 back up radar 8 left rear combination lamp
3 fuel pump 9 right backup radar probe
4 fuel sensor 10 right rear fog lamp
5 left backup radar probe 11 right license lamp
6 left rear fog lamp 12 right rear combination lamp
 Body Electric System
Wire Harness Distribution BE-83

Chassis wire harness (continued)

SL SK

6
5
chassis wire harness tail lamp wire harness
1 7
3
8

10
2
11

12

Tail lamp wire harness should be fixed at the inner side of the rear baffle of load-compartment.

1 connected to cab wire harness 7 right rear fog lamp

2 fuel pump 8 back up radar control box
3 grounding wire 9 right license lamp
4 connected to wire harness 10 left license lamp
5 connected to chassis wire harness 11 left rear fog lamp
6 right rear combination lamp 12 left rear combination lamp
BE-84 Body Electric System
Wire Harness Distribution

Chassis Wire Harness (continued)

SY SJ
only for SJ model vehicle

2 3

5
6
4

1 connected to cab wire harness

2 right rear combination lamp
3 right rear fog lamp
4 electric fuel pump
5 left rear fog lamp
6 left rear combination
 Body Electric System
Wire Harness Distribution BE-85

Chassis Wire Harness (continued)

SF

1 2

1 fuel level sensor

2 electric fuel pump
3 connected to cab wire harness
 AC-1

Air-conditioning System
Page

Introduction ................................................................. AC-2

Electric circuit diagram of air-conditioning system ...... AC-4
System constitutes ...................................................... AC-8
General introduction .................................................... AC-9
Troubleshooting .......................................................... AC-10
Inspection for refrigerant quantity ................................ AC-11
Compressor ................................................................. AC-12
Liquid container ........................................................... AC-14
Condenser ................................................................... AC-15
Cooling device ............................................................. AC-16
Refrigerant pipeline ..................................................... AC-20

AC
AC-2 Air Conditioning System
Introduction

General Introduction
1. Take notice when handling refrigerant General Introduction
(a) Do not handling with refrigerant in the closed room or
near to open fire.
(b) Safety goggles shall be worn when handling
(c) Be careful to avoid the liquid refrigerant from entering
into your eye or touching you skin.

In case the liquid refrigerant enters into the eye or touches the
skin, the following measures shall be taken:

Wash the part where is touched by the refrigerant with a
great deal of water.

Coat the skin with the clean Vaseline.


See the doctor or go to the hospital for treatment; and


Do not try to cure it yourself.

2. Take notice when changing the parts of refrigerant pipes:

air (a) The refrigerant shall be exhausted gradually before
water
changing.
(b) The dismantled parts shall be covered with plug right
dust away so as to prevent the water or dust from entering into
the system.
(c) Do not store the condenser or liquid tank under the
condition that the plug has been uncovered. and
plug
(d) Refrigerant shall be exhausted before installing the new
condenser, because the refrigerant, if not exhausted, will
eject out in gaseous form with the lubricant oil when the
plug is moved away.

3. Take notice when fastening the connection parts:

(a) Spread a little lubricant oil at the matching position of the
O-type ring to fasten the connection and avoid of gaseous
refrigerant leakage.
(b) Fasten the nut with two spanners so as to avoid of the pipe
deformation.
ÅçåÇÉåëÉê
 Air Conditioning System
Introduction AC-3

over-fastened (c) Tighten the O-ring matching position or the threaded position
to the specified moment.
4. Take notice when connecting measuring meter at branch pipes:
(a) Connect the end of filling hose with high speed joint to the
filling valve of compressor.
loose (b) Letter
D
marked on the compressor near the auxiliary valve
represents the side of high voltage while
S
means the side of
low voltage, which shall be looked out when connecting the hose.
(c) Fasten the bolts by hand, and
measuring meter of branch pipe (d) In order to prevent the hose from loosing, lubricant oil shall not
be spread at the connection position.
Remarks: after connecting the measuring meter on branch pipes to
the refrigerant container (repairing tank), the air in the hose shall be
exhausted up.
5. Take notice when vacuumizing:
After vacuumizing for 20 min, maintain the container at certain
pressure to ensure that all air in it is exhausted up, and another
inspection shall be made to see whether there is leakage.

6. Take notice when handling with the refrigerant container

under 40

(repairing tank):
(a) Do not heat it.
(b) Store the container at the place where temperature is under 40

(c) In case of heating the repairing tank with hot water, care shall
be paid to the valves at the top of tank, do not dip them into the
water, or the water will penetrate into the cooling system.
(d) The empty repairing tank is forbidden to reuse.
incorrect correct 7. Take notice in the A/C operation or when adding the liquid
refrigerant:
(a) In case the gaseous refrigerant in the cooling system is
insufficient, which can lead to the compressor burns out, and
such accidents shall be avoided.
(b) If the valve on the side of high pressure is uncovered, the
A/C operation refrigerant will flow in the reverse direction, which may lead
to the break of the repairing tank, therefore, only valves on the
side of low pressure are allowed to open or closed.
(c) If the repair tank is laid in reverse direction, and the refrigerant
is added in liquid status, the liquid refrigerant will be
compressed, which may lead to failure of the compressor,
therefore, refrigerant shall be inflated in the gaseous status.
(d) Be careful not over-inflate the gaseous refrigerant, otherwise,
such failures as insufficient cooling, increase of oil consuming
or over heat of engine will be followed.
8. Take notice when using the high-pressure air cylinder type
inspecting device:
(a) In case the open fire is used, it is the first to ensure before using
there is no flammable material around.
(b) Be careful because toxic gas will be produced when the
gaseous refrigerant meets with the open fire.
AC-4 Electric Circuit Diagram of Air
Conditioning System

Electric circuit diagram of air-conditioning system (continued)

Dr
ignition switch

air-conditioning relay
5
pressure switch A/C switch
^`` lk pq engine wire
2 5 3 4 2 harness
fuse

fuse air blower

M

fuse 2 speed-adjusting 4
module
1 3
6 4 5
battery

wind speed switch

speed adjusting
ignition switch pressure switch A/C switch module of air blower

1 2 1 2 2 N
5 4 3 2 1

10 9 8 7 6 3 4 5 6 3 4 5 6 4 3

socket connectors of engine wire harness wind speed switch

6 5 4 3 2 1 N O P Q R

13 12 11 10 9 8 7 S T U
 Electric Circuit Diagram of Air
Conditioning System AC-5

Electric circuit diagram of air-conditioning system (continued)

SF

three-state pressure switch

fuse
ignition switch

small light relay

N P

b`r
O Q

water temperature relay

power resistor
fuse
P

compressor relay
5
6
24 20
fuse

ACC ON ST
18
5
11

electromagnetic
17

fan relay
16
main air-conditioning 3
15
control panel 19
14
22
1
10

electronic fan
7 9 8 13
23
1 3 65 Q N PS R Q N P SR Q j

compressor clutch
4
3 speed
M j j
adjusting
battery

module mode circular cold-hot

servomotor servomotor servomotor
O O O
M air blower S
water
valve
fuse

+12V

ignition switch modular air-door motor cold-hot air-door motor air-in motor

5 4 3 2 1 3 2 1 3 2 1 3 2 1

10 9 8 7 6 6 5 4 6 5 4 6 5 4

speed adjusting three-stage

air conditioning
modul pressure switch

2
12 11 10 9 8 7 6 5 4 3 2 1 3 2 1
3 1
24 23 22 21 20 19 18 17 16 15 14 13 6 5 4
4
AC-6 Air-Conditioning System
(Electric Circuit Diagram)

Electric circuit diagram of air-conditioning system (continued)

SL SK SJ
fuse

charging indicating lamp

fuse
4 fuse ECU
ignition switch

5 ECU

blower relay
1

fuse
^``lkpq

A/Cswitch

compressor relay
1

blower
3 2
speed-adjusting resistance

request relay
air-conditioning
air-conditioning 2
request relay 4 5 6
battery

heat-sensitive resistance

compressor
electromagnetic fan relay
3 2
air-volume switch

3 6 54

connect with ECU 2 1

1
pressure switch

S electromagnetic fan

ignition switch speed adjusting module air-volume switch

4 3 2 1 3 2 1 3 2 1

8 7 6 5 6 5 4 6 5 4

air blower A/C SWITCH pressure switch

1 1
1

2 3 2 2
 Air-Conditioning System
(Electric Circuit Diagram) AC-7

Electric circuit diagram of air-conditioning system (continued)

SY
compressor
compressor relay

switch
rearignition temperature
fuse

ECU
temperature controller
1 2 3
rearignition switch electromagnetic

controller
cutoff valve
2 1 2
1 3
3 3 2 1

velocity switch
rear speed-adjusting
rear wind-velocity switch resistance

rear wind-
rear air-conditioning relay 2 1
2 2 air blower
3 1 1 4
4 3
4 3

adjusting
rear speed-
1 2
resistance
electromagnetic fan relay 3 4
ECU fuse
electromagnetic fan
speed-adjusting

A/C switch
resistance

3 2 1
1
pressure switch
6 air-conditioning request relay 6 5 4
R

speed-adjusting resistance
fuse

(air-volume

3 2
switch)

air-volume

air 5 3 2 1
switch

blower relay blower 5

2 4
6 1 6 5 4
4 3 6
A/C switch

4 3 2 1
air-conditioning
(electricity-connecting and
charging indicating lamp request relay
8 7 6 5
heat-sensitive resistance
ignition switch

STON ACC
4
fuse

5
ignition switch

4 3 2 1
connect with ECU
battery

8 7 6 5
AC-8 Air-Conditioning System
System Component

system component

LP hose
HP hose
evaporator

compressor

liquid tank

condenser

Tightening moment for air-conditioning pipeline

SL SK SY SJ

Open-wrench spanner (mm) Tightening moment(N
m)

14
17 15
3
17
19 15
3
19
19 15
3
Threaded
joint 22
24 25~30
24
27 30~35

27
27 30~35

Threaded head (mm) Tightening moment(N
m)

Pressing Dr SF
10 8~12
plate bolt
14 21~25 Air-conditioning pipe-line Tightening moment(N
m)

Threaded Open-wrench spanner (mm) Tightening moment(N
m) LP hose interface 35
3

joint of
24 25~30 HP hose interface 25
2
com-
pressor 14 30~35 HP hose interface 18
1.5
 Air-conditioning System - General introduction AC-9

diaschage vent indraft vent General introduction

Refrigeration cycle
1. The refrigerant at the lower pressure side is condensed by the
expansionvalve
heat compressor compressor into the HT and HP gaseous refrigerant.
curent direction
heat 2. These gaseous refrigerant flows into the condenser, where it is
turned into liquid refrigerant.
evaporator 3. Those liquid refrigerant flows into the liquid tank, where the
liquid refrigerant is stored and filtered so as to satisfy the
liquid tank
requirement of evaporator.
4. The liquid refrigerant is throttled by the expansion valve to reduce the pressure, so that the liquid refrigerant is turned
into the LT and LP mixture of liquid and gaseous refrigerant.
5. The cold and fog-like refrigerant flows into the evaporator, where it is vaporized with the given heat, which is
absorbed from the hot air flow by the evaporator core. All liquid refrigerants are turned into the gaseous refrigerant
in the evaporator, and only the heated gaseous refrigerant is absorbed into the compressor. Then repeat the above-
mentioned cycling approach.

The refrigerant released from

the evaporator expands and
The compressor absorbs the
inflows through the evapora- gaseous refrigerant emitted
tor pipe. During this process, from the evaporator and com-
presses it. In doing so, the tem-
the refrigerant absorbs the perature and pressure of gas-
heat in the air around the ra- eous refrigerant increases
rapidly.
diating rib and pipe and
vaporizes, so that the tem-
perature inside the vehicle
reduces gradually.

The expansion valve is used

to measure the gaseous re- The liquid tank is used to exhaust
The condenser allows the heated gas-
frigerant entered into evapo- the water in system and to filter
eous refrigerant to release heat to the
rator core, which reduces the the dust and dunghill. It serves as
cooling air of engine, therefore, the gas-
pressure and temperature of the store to store the redundant
eous refrigerant is cooled and turned
refrigerant gradually. refrigerant.
into liquid state again.
AC-10 Air-conditioning System - Troubleshooting

Troubleshooting
Trouble Possible causes Reparation approaches Page
Lack of cold air Non-pull-in performance of electromagnetic clutch:
(a) Break of ignition switch and fuse; Change the fuse and check to see whetherPage AC-4 to 7
there is short circuit;
(b) Trouble of electromagnetic clutch; Check the electromagnetic clutch; Page AC-12
(c) Trouble of A/C switch; Check the A/C switch; Page AC-4 to 7
(d) Wiring or grounding trouble; Repair it as requirement; Page AC-11
(e) Lack of refrigerant; and Check the refrigerant pressure;
(f) Trouble of pressure switch. Check the pressure switch;
Abnormal operation of compressor:
(a) Looseness or break of driving belt; Adjust or change the driving belt; Page AC-13
(b) Compressor trouble; Check the compressor; Page AC-12
Expansion valve trouble; Check the expansion valve; Page AC-16
Systematic leakage; Conduct lubricating test for the system
Liquid tank fusible plug melting or filtering Check the liquid tank; Page AC-14
screen blocking;
Non-work of air blower:
(a) Failure of A/C switch; Check the A/C switch;
(b) Failure of air blower motor, and Check the air blower motor;
(c) Wiring failure. Conduct reparation as requirement. Page AC-4 to 7
Inconsecutive Electromagnetic valve slip Check the electromagnetic clutch; Page AC-12
cold air Failure of expansion valve; Check the expansion valve; Page AC-16
Wiring or connecting failure; Make reparation as requirement. Page AC-4 to 7
Over water content in system Reclaim the water first, then exhaust the
system to vacuum and inflate in the refrigerant.
Cold air occurs in Blocking of radiating face of condenser; Check and wash the condenser Page AC-15
high-speed condition Driving belt slip; Check and change the driving belt; Page AC-13
Compressor failure; Check the compressor; Page AC-12
Insufficient or redundant refrigerant; Check the refrigerant quantity; Page AC-11
Air existing in system Vacuumize the system and inflate
the refrigerant;
Insufficient Condenser blocking; Check the condenser; Page AC-15
cold air Driving belt slip; Check and change the driving belt; Page AC-12
Electromagnetic clutch failure; Check the electromagnetic clutch; Page AC-12
Compressor failure; Check the compressor; Page AC-12
Expansion valve failure; Check the expansion valve; Page AC-16
Insufficient or redundant refrigerant; Check the refrigerant quantity; Page AC-11
Air existing in system; Reclaim the air, then vacuumize the sys-
tem and inflate the refrigerant;
Redundant compressor lubricant; Check the compressor lubricant quantity;
Liquid tank block Check the liquid tank Page AC-14
Under-speed cold air Evaporator blocking or frosting Clean the evaporator radiating rib Page AC-18
or filter;
Air leakage in cooling device or air Make reparation as requirement Page AC-20
pipeline;
Air inlet blocking; Make reparation as requirement
Air blower motor failure; Change the air blower motor.
 Air-Conditioning System
Inspection On Refrigerant Quantity AC-11

Dr SF observation window Inspection on Refrigerant Quantity

1. Run the engine at the speed of 1500 r/m or so (the
atmospheric temperature should be above 35
);
2. Start the air-conditioner in the max cold air status for
several minutes;
3. Check the refrigerant quantity.
Watch the observation window on liquid tank.
liquid tank

SL SK SY SJ observation window

liquid tank

No. Symptoms Refrigerant quantity Repairing approaches

Air bubble occurs in the observa- Check to see whether there is leakage with the
1 tion window Insufficient
gas leakage detector

No air bubble in observation win-

2 No, normal or redundant Refers 3 and 4.
dow

Vacuumize the system and inflate the

No temperature difference between
3 No, or almost no refrigerant, then check to see whether there is
the inlet and outlet of compressor
leakage with the gas leakage detector.

Obvious temperature difference be-

4 Normal or redundant Refer 5 and 6
tween the inlet and outlet of compressor.

Observation window is in clear status Exhaust the redundant refrigerant until the speci-
5 Redundant
once the air-conditioner is turned off fied quantity is satisfied.

There is refrigerant foam on observa-

tion window after the air-conditioner
6 Normal
is turned off, then the observation
window becomes clear.
AC-12 Air-Conditioning System
Compressor

packing hose
Compressor
Installation of manifold gauge
efrigeration system
Remark: Connect the manifold gauge to the auxiliary valve of
compressor.
1. Turn off the manual valve of manifold gauge.
connected to mani- 2. Mount the packing hose of manifold gauge on the packing
fold gauge valve.
connect to compressor
Mount the LP hose to the LP packing valve and the HP hose to
HP packing valve. Then screw up the nuts for hose joint by
hand.
Remark: Do not coat the compressor lubricant on the connec-
turn off tion positions.

turn off

On vehicle inspection
1. Mount the manifold gauge;
(see manifold gauge mount)
2. Run the engine at the speed of 1500 r/m or so;
3. Check the compressor according to the following items:
(a) The HP gauge readings under the normal system should
satisfy the specified value of (1.4-1.7)MPa , that of LP
gauge should meet the specified value of (0.15-0.2)MPa .
(b) Whether there is abnormal sound;
(c) Whether there is leakage at the shaft oil seal.
If any problem is found, repair or change the compressor.
4. Check the electromagnetic clutch:
(a) Check to see whether there is lubricant trace on the
pressing plate and rotor;
(b) Check to see whether there is noise or lubricant leakage
at the clutch bearing;
(c) Measure the resistance between the stator coils that is set
between the clutch lead and the grounding lead with the
ohmn meter.
Standard resistance:
SL SK SJ
(3.2
.2)Ω
Dr SF SY
(3.5
.2)Ω
In case the requirement is not satisfied, change the compressor.
 Air-Conditioning System
Compressor AC-13

Disassemble of compressor
1. Run the engine in the idle status for ten minutes under
the air-conditioning situation;
2. Turn off the engine;
3. Disconnect the cathode lead from the storage cell;
4. Disconnect the electromagnetic clutch lead from the
matching wire;
5. Exhaust the refrigerant from the refrigeration system;
6. Disconnect the two hoses from the auxiliary valve of
compressor;
Cover the opening joint with cork right away to prevent the wet
gas entering in to the system.
7. Tear down the compressor:
(a) Tear down the fan cover;
(b) Loosen the driving belt;
(c) Tear down the fixing bolts of compressor bracket and the
compressor.

Mount of compressor
incorrect correct incorrect
1. Mount the compressor with fixing bolts;
Tightening moment
(25-30)N
m
2. Mount the driving belt correctly;

Requirement for belt tension: the tension belt is allowed

98N
to reduce (9-13)mm under 98N after the compressor
runs for five minutes;

3. Connect the two hoses to the auxiliary valve of

compressor;
Tightening moment
(see page AC-8)
4. Connect the clutch lead to the matching wire;
5. Connect the cathode lead of storage cell to the storage
cell, and
6. Vacuumize the system and inflate the refrigerant:
Vacuum time:
Dr SL SK SF SJ
Vacuumize for 20min and main-
tain the pressure for 30min;
SY
Vacuumize for 30min and maintain for 30min
Inflated refrigerant quantity:
Dr
(600-650)g
SL
700
0g
SK SJ
560
0g
SF
(700-720)g
SY
850
0g
AC-14 Air-Conditioning System
Liquid Tank

Liquid Tank
Check to see whether there is leakage in observation window,
fusible plug and joints;
Conduct the inspection with the gas leakage detector and, if
necessary, repair or change the liquid tank.

Dr SF condenser liquid pipe Dismantle of Liquid Tank

1. Exhaust the refrigerant;
2. Tear down the two liquid pipes from the liquid tank;
Remark: the opened joint should be plugged with cork so as to
prevent the humid air from entering into the system.
3. Tear down the liquid tank from the tank bracket.
Mount of Liquid Tank
liquid pipe liquid tank
1. Mount the liquid tank on the liquid tank bracket;
Remark: the cover of joint should not be take down before
SL SK SY SJ connecting the pipe;
liquid pipe condenser
2. Connect the two liquid pipes to the liquid tank;
Tightening moment
(See page AC-8)
3. Vacuumize the system and inflate the refrigerant in;
Vacuumizing time:
Dr SL SK SF SJ
Vacuumize for 20 min and main-
tain the pressure for 30min;
SY
Vacuumize for 30 min and maintain the pres-
liquid tank liquid pipe
sure for 30min.
4.
Dr
(600-650)g
SL
700
0g
SK SJ
560
0g
SF
(700-720)g
SY
850
0g
 Air-Conditioning System
Condenser AC-15

Condenser
Condenser dismantle
1. Check the radiating ribs of condenser to see whether
there is blocking or damage;
if the radiating rib is blocked, wash it with water and dry it with
compressed air.
Notice: be careful not to damage the radiating rib;
2. Check the condenser joint to see whether there is leakage;
Make reparation as requirement;

Dr SF Condenser disassembly
outlet hose condenser 1. Exhaust the refrigerant;
liquid pipe 2. Tear down the median mesh and the bonnet lock bracket;
3. Disconnect the outlet hose from the entrance joint of
condenser;
4. Tear down the liquid pipe from the outlet of liquid tank;
Remark: the opened joint should be plugged with cork so as to
prevent the humid air from entering into the system.
liquid pipe liquid tank
5. Tear down the condenser:
Tear down the two bolts.
SL SK SY SJ liquid pipe
condenser

Condenser mount
1. Mount the condenser
Screw on the two bolts so that the rubber washer contacts the
mounting flanges correctly.
2. Connect the liquid pipe to the liquid tank and the outlet
liquid pipe liquid tank hose to the condenser.
Tightening moment
(See page AC-8)
3. Mount the median mesh and the bonnet lock bracket;
4. vacuumize the air-conditioning system;
Vacuumizing time:
Dr SL SK SF SJ
vaccumize for 20min and main-
tain the pressure for 30min;
SY
vaccumize for 30min and maintain the pres-
sure for another 30min.
5. Inflate the refrigerant in the air-conditioning system and
check to see whether there is air leakage:
Dr
(600-650)g

SL
700
0g
SK SJ
560
0g
SF
(700-720)g
SY
850
0g
AC-16 Air-Conditioning System
Refrigeration Device

Refrigeration device
On-vehicle inspection on expansion valve
1. Check the gaseous refrigerant quantity in the refrigeration
cycle;
2. Mount the manifold gauge;
(see Page AC-12)

3. Run the engine;

Run the engine at a speed of 2000 r/m for five minutes.
4. Check the expansion valve;
If the expansion valve is blocked, the LP readings will reduce
to 0 kPa, otherwise, the valve is normal.

Disassembly of Refrigeration Device

1. Disconnect the cathode lead from the storage cell;
2. Exhaust the refrigerant;
3. Tear down the suction pipe from the entrance joint of
refrigeration device;
4. Tear down the outlet pipe from the entrance joint of
refrigeration device;
refrigeration device Remark: the opened joint should be sealed with the cork to
prevent the humid air from entering into the system.
SY 5. Tear down the insulation rings from the inlet and outlet
interior trim panel joints.
at left rear side
6. Tear down the right glove box (SY rear air-conditioner:
tear down the interior trim panel at left rear side).
7. Disconnect the plugging element;
8. Tear down the refrigeration device;
Tear down the three nuts.

rear evaporator
 Air-Conditioning System
Refrigeration Device AC-17

evaporator housing
Dr SF
evaporator housing

residual liquid pipe

evaporator core
heat-sensitive
resistance pressure switch

expansion valve

SL SK SY SJ HP/LP pressure rubber

evaporator upper evaporator core HPpressure rubber

housing LPpressure rubber

heat-sensitive
resistance

evaporator lower expansion valve

housing
AC-18 Air-Conditioning System
Evaporator

SYrear evaporator
heat-sensitive resistance

upper housing
air pipe
air cover

evaporator core

air blower
temperature controller

lower housing

1. Tear down the evaporator housing:

(a) Disconnect the plugging element;
(b) Tear down the two clipes;
(c) Tear down the four screws;
(d) Tear down the upper cluster housing;
(e) Tear down the HP/LP pressure pipe rubber washers; and
(f) Tear down the lower cluster housing.
2. Tear down the expansion valve:
(a) Tear down the liquid pipe from the entrance joint of
expansion valve;
expansion valve LP pipe HP pipe
(b) Tear down the sealing washer and thermal bulb from the
suction pipe of evaporator;
(c) Tear down the expansion valve.
 Air-Conditioning System
Refrigeration Device AC-19

inspectionofevaporator
1. Check the radiating ribs of evaporator to see whether there is
block.
If the radiating rib is blocked, clean it with the compressed air.
Notice: do not wash the evaporator with water.
2. Check the joint to see whether there is crack or scrape.
Make reparation as requirement.

Mount the evaporator parts:

expansion valve HP pipe LP pipe
(a) Connect the expansion valve to the entrance joint of evaporator
and screw up the nuts.
Remark: Carefulness should be put on the O-ring seal.
(b) Mount the bracket on the suction pipe with thermal sensor;
(c) Connect the liquid pipe to the entrance joint of expansion
valve and screw up nuts.
(d) Mount the lower cluster housing on evaporator.
(e) Mount the upper cluster housing;
(f) Mount the four screws;
(g) Mount the two clipes;
(h) Mount the HP/LP pressure rubber washer; and
(i) Connect the plugging elements;

1. Mount the refrigeration device.

Mount the refrigeration device with three nuts.
2. Connect the plugging elements;
3. Mount the right glove box (SY rear air-conditioner: mount the
interior trim panel at left rear side).
4. Mount the insulation ring on the inlet and outlet joints;
5. Connect the liquid pipe to the outlet joint of refrigeration device;
Tightening moment
(see page AC-8)
6. Connect the suction pipe to the outlet joint of refrigeration pipe;
Tightening moment
(see page AC-8)
7. Connect the cathode lead to the storage cell.
8. Vacuumize the air-conditioning system:
Vacuumizing time:
Dr SL SK SF SJ
vacuumize for 20min and maintain the
pressure for 30min
SY: vacuumize for 30min and maintain the pressure for
another 30min.
9. Inflate the refrigerant in the air-conditioning system and
check to see whether there is air leakage;
Refrigerant quantity:
Dr
(600-650)g
SL
700
0g
SK SJ
560
0g
SF
(700-720)g
SY
850
0g
AC-20 Air-Conditioning System
Refrigerant Pipe

Refrigerant pipe
On-vehicle inspection
1. Check the pipelines of each part to see whether there is
leakage:
Make the inspection with the gas leakage detector and, if
necessary, change them.
2. Check the clamping parts of the pipelines to see whether
there is looseness;
Make a new fastening or change as requirement.
Change of refrigerant pipeline
1. Exhaust the refrigerant;
2. Change the damaged pipe or hose
Remark: the opened joint should be sealed right away with
cork so as to prevent the humid from entering into the system.
3. Screw up the O-ring seal joint and threaded joint according
to the Tightening moment;
4. Vacuumize the air-conditioning system:
Vacuumizing time:
Dr SL SK SF SJ
Vacuumize for 20min and main-
tain the pressure for 30min;
SY
Vacuumize for 30min and maintain the pres-
sure for another 30min.
5. Inflate the refrigerant in the air-conditioning system and
check the system to see whether there is air leakage;
Refrigerant quantity:
Dr
(600-650)g
SL
700
0g
SK/SJ
560
0g
SF
(700-720)g
SY
850
0g
 B0-1

Vehicle Body
Page

Introduction ................................................................. BO-2

Engine cover ............................................................... BO-3
Front door .................................................................... BO-4
Rear car Door .............................................................. BO-10
Body collision avoidance adhesive strip ...................... BO-20
Wheel-trims ................................................................. BO-24
Wheel-trims wrapping angle and exterior trim panel ... BO-26
Front Windshield ......................................................... BO-32
Side-window glass ...................................................... BO-37
Rear-door glass ........................................................... BO-40
Rear windshield ........................................................... BO-41
Load-compartment baffle ............................................ BO-43
Tail door ....................................................................... BO-45
Instrument panel ......................................................... BO-50
Safety belt ................................................................... BO-57
Seat ............................................................................. BO-60
Spoiler ......................................................................... BO-63
Luggage rack .............................................................. BO-65
Reserve tire bracket .................................................... BO-66 BO
Body dimension ........................................................... BO-68
Frame dimension ........................................................ BO-78
B0-2 Vehicle Body
General Introduction

General Introduction
In case there is damage to body and/or part, protection measures
should be taken first to prevent the vehicle from damaging before
repairing them.
Example:
1. Protection adhesive strap should be contacted on the relative
part of body when conduct the disassembling and mounting
operation.
2. When prizing the body parts with screwdriver or scraper, those
body parts head or the edge of screwdriver or scraper should
be wrapped with adhesive strap to prevent paint layer and the
body from damaging.

adhesive strap

If the antirust is damaged when repairing other parts, it should be

peel-off recoated in time.
Example:
1. In case the sealing agent, paint layer or priming coat on the
body is damaged due to peel-off or crack, etc. the correspond-
ing antirust shall be used for reparation.

crack

2. If the hinge or plate is loosened or torn down, the antirust

should be re-coated after repairing them.

anti-rust agent
 Vehicle Body
Engine Cover B0-3

Engine cover
Adjustment of engine cover
Remark
as the centering bolt are used as the fixing bolt to fix the
hinge of engine cover, the engine cover cannot be adjusted when
mounting, in such case, the bolt with a washer should be used to
substitute the centering bolt.
centering bolt bolt with washer

1. Adjust the engine cover in front-back and right-left

direction.
Loosen the hinge bolts on engine cover to adjust the engine
cover.

2. Adjust the engine cover leading edge vertically;

Rotate the buffer block to adjust the engine cover.

3. Adjust the lock clips on engine cover Loosen the bolt to

adjust the lock clip.
B0-4 Vehicle Body
Front Door

Front door
Element figure

(glass)
glasschannel

outer auchi
outdoor handle

lock barrel

snapping ring

glass bracket and glass gasket

rear vision mirror

lock ring
inner tri-angle trim panel
lock clip lower front glass
guide track
door lock assembly
small sliding track
sliding channel
door limiting device
lower rear glass
guide track door hinge

indoor handle

inner clip seal strip on

door plate electric switch
and panel

door lamp

manual interior
trim panel(Dr)
interior trim panel
elevator handle of electric door
sleeve
(Dr)
snapping ring

interior trim panel

of electric door
interior trim panel of (SF)
electric door
(SL SK SY SJ)
Vehicle Body
Front Door B0-5

Adjustment of front door

1. Adjust the car door in the front-back and vertical direction;
Adjust the car door under the condition that the bolts of body
side hinge are loosened.

2. Adjust the car door in left-right and vertical direction

Adjustment should be made after the bolts of side hinge of
body are loosened.

3. Adjust the clip of door lock:

(a) Check whether the car door assembly and the match of
door lock are adjusted correctly.
(b) Loosen the lock clip lightly to mount the screws and tap
the lock clip with hammer to adjust their positions.
(c) Screw off the fixing screws of lock clip.

Disassembly of front door

1. Tear down the elevator handle (Dr)
Pull out the snapping ring of spring with dishcloth and tear
down the elevator handle and the sleeve.

2. Tear down the indoor handle

3. Tear down the inner triangle trim panel;
Loosen the clip open with a screwdriver to tear down the inner
triangle trim panel.
Notice: before using the screwdriver, wrapping the
screwdriver head with adhesive strap.
4. Tear down the rear vision mirror;
Tear down the three screws and rear vision mirror.
B0-6 Vehicle Body
Front Car Door

manually operated indoor plate 5. Tear down the interior trim panel of car door:
(a) Tear down the inner clip bolts and the inner clip.
(b) Tear down the door lamp bolts and the door lamp;
(c) Insert the screwdriver into seam between fixing clip and
interior trim panel of car door to loosen the interior trim
panel.
Notice: before using the screwdriver, wrap its head with
12 clips adhesive strap.
(d) Tear down the interior trim panel of car door.
inner plate of electric door (type A) (Dr SF)
(a) Tear down the inner clip bolts and the inner clip;
(b) Tear down the door lamp bolts and the door lamp;
(c) Tear down the electric switch and panel.
(d) Insert the screwdriver into the seam between fixing clip
and the interior trim panel of car door to loosen the
interior trim panel.
12 clips
Remark: use the adhesive strap to wrap the screwdriver
head before using.
inner plate of electric door (type B)
(e) Tear down the interior trim panel of car door.

SL SK SY SJ)
(a) Tear down the door lamp bolts and the door lamp;
(b) Tear down the electric switch and the panel;
(c) Tear down the screw covers and screws on the indoor
trim panel
ten clips (d) Insert the screwdriver into the seam between the fixing
four sets of bolt and nut clip and the interior trim panel of car door to loosen it.
Notice: use the adhesive strap to wrap the screwdriver
head before using.
(f) Tear down the interior trim panel of car door.

6. Tear down the outer auchi

Loosen the clip along the edge of paneling to tear down the
outer

7. Tear down the door and window glass;

(a) Tear down the fixing bolts in the two glass sliding-
grooves.
(b) Pull up the glass to take it down.

8. Tear down the glass groove on car door.

 Vehicle Body
Front Car Door B0-7

9. Tear down t the lower rear glass guide track:

Tear down the bolts and guide track.

10. Tear down the lower front glass guide track;

Tear down the bolts and guide track.

11. Tear down the glass elevator:

(a) Tear down the two fixing bolts of small sliding track;
(b) Tear down the fixing bolts of three elevators (manually
operated)
Tear down the fixing bolts of four elevators. (electric)
(c) Tear down the elevator through the auxiliary hole.

12. Tear down the lock ring inside the vehicle;

Disconnect the control lever to tear down the lock ring inside
the vehicle.

13. Tear down the door lock and outdoor handle with lock
barrel;
(a) Disconnect the control lever from the outdoor handle
with lock barrel.
(b) Tear down the 3 bolts and door lock.
(c) Tear down the two bolts and outdoor handle with lock
Dr. SF barrel.
(d) Tear down the spring snapping ring and lock barrel.

Change of Glass
170mm (Dr SF)
1. Tear down the glass bracket with screwdriver or similar
tool;
2. Coat the black glue on the inside of glass bracket liner;
SL. SK. SY. SJ 3. Tap the glass bracket with rubber hammer to encase it in.

(SL SK SY SJ)
1. Tear down the bolts on gear plate with pliers or similar
tool;
2. Tear down the bolts of glass bracket of car door to take
out the glass.
B0-8 Vehicle Body
Front Door

Assembly of Front Door

1. Coat the MP lubricant on the parts before mounting.
(a) Coat the MP lubricant on the sliding face and the gear of
glass elevator.
Notice: Do not plaster the MP lubricant on the spring of
glass elevator.
(b) Plaster the MP lubricant on the sliding face of door lock.

2. Mount the outdoor handle with lock barrel and the door
lock;
(a) Mount the lock barrel on the outdoor handle with spring
snapping ring;
(b) Use two bolts to mount the outdoor handle and the lock
barrel;
(c) Mount the door lock with three screws;
(d) Connect the outdoor handle to the control lever.

3. Mount the lock ring inside vehicle

Mount the lock ring inside of vehicle and connect the control
lever.
4. Mount the lower rear glass guide track,
5. Mount the lower front glass guide track;

6. Mount the glass elevator:

(a) Put in the elevator through the auxiliary hole;
(b) Mount on the three fixing bolts of elevator. (manually
operated)
Mount on the four fixing bolts of elevator (electric)
(c) Mount the small sliding track, and screw up the bolts of
small sliding track temporarily.
7. Mount the glass groove on car door;

8. Mount the car door and window glass;

Put the glass in the car door cavity, and then use two bolts to
fix the glass on the elevator.
 Vehicle Body
Front Door B0-9

9. Adjust the car door and window glass;

Adjust the balance arm upwardly or downwardly until the
dimensions of A and B shown in drawing are equal, and then
fix the balance arm.
10. Mount the outer
Encase the claw of clip into the paneling seam and press the
outer on the paneling.
11. Mount the rear vision mirror

manual indoor plate 12. Mount the interior trim panel of car door:

Dr)
(a) Connect the handle to the control lever first, then pull it
out from the indoor handle hole.
(b) Fix the clip by tapping to encase the interior trim plate of
car door in the corresponding hole of car door interior
12 clips panel.
(c) Use one screw to mount the inner clip.

Electric indoor plate (Type A)
Dr SF)

(a) Connect the handle to the control lever first, and then pull
it out from the indoor handle hole.
(b) Fix the clip by tapping to encase the interior trim panel in
the corresponding hole of car door interior panel
(c) Mount the inner clip with one screw; and
(d) Mount the electric switch and panel.
12 clips

SL SK SY SJ)
(a) Connect the handle with the control lever first, then pull
inner panel of electric door (type B)
out it from the indoor panel handle.
(b) Connect the plugging elements.
(c) Fix the clip by light tapping to encase the interior trim panel
of car door in the corresponding holes on indoor panel.
(d) Mount the inner clip with two bolts;
(e) Mount the four screws to fasten the interior trim panel of
ten clips car door, and cover the nuts.
four sets of bolt and nut (f) Mount the electric elevator switch.

13. Mount the indoor handle:

(a) Push the indoor handle into the car door paneling and
make it slide backward.
(b) Screw on the screws;
front
14. Mount the elevator handle (Dr)
Mount the paneling and elevator handle with spring snapping
ring under the condition the car doors and windows are closed
completely as shown in drawing.
B0-10 Vehicle Body
Rear Door

Rear Door (
)

Element Figure
Dr SL SK SY

glass

glass channel

outdoor handle
glass bracket and glass gasket

Outer auchi

door lock assembly

lock clip

lock ring
lower rear glass
guide track door hinge

small sliding track

lower dust
strip door limiting
inner clip device

manual interior
trim panel
door lamp (Dr)

interior trim panel

of electric door
(Dr)

sleeve electric switch

indoor handle

interior trim panel

elevator handle of electric door
snapping ring (SL,SY,SK)
 Vehicle Body
Rear Door B0-11

Rear Door (
)

Element Figure
SF

quarter window glass glass

glass channel

outdoor handle Outer auchi

upper glass guide track
glass bracket and
glass gasket

door lock assemblyn

lock clip
lock ring
lower rear glass
guide track

small
door hinge
sliding
track
door limiting
sliding device
inner clip channel

electric switch

door lamp

indoor handle
B0-12 Vehicle Body
Rear Door

Rear door(
)
Element figure
SJ

glass

glass channel

quarter
window glass glass supporter
outer auchi

door lock assembly

lock clip
lock ring

outdoor handle

door hinge

door limiting device

inner clip

electric switch

indoor handle

screw cap
Vehicle Body
Rear Door B0-13

Adjustment of Rear Door

(Dr SL SK SF SY SJ)
1. Adjust the door along the front-back and vertical direction;
(upper side)
Screw off the hinge nuts on the body side for the adjustment.
(lower side)
Screw off the hinge nuts on the side body for the adjustment.

2. Adjust the door along the left-right and vertical direction.

3. adjust the door lock clip

(a) Screw off the mounting bolts of lock clip and tap the lock
clip with hammer to adjust its position.
(b) Screw on the fixing nuts of lock clip.

Disassembly of Rear Door

1. Tear down the elevator handle (Dr)
Pull out the spring snapping ring with dishcloth and tear down
the elevator handle and sleeve.

2. Tear down the indoor handle;

(a) Take spart the screw and slide the handle forwardly.
(b) Take down the handle from the controlrod
B0-14 Vehicle Body
Rear Door

3. Tear down the door interior trim panel

manually operated indoor plate (Dr)
Dr manually operated)
(a) Tear down the inner clip bolts and inner clip;
(b) Tear down the door lamp bolts and the door lamp;
(c) Insert the screwdriver into the seams between fixed
clipes and the door interior trim panel.
Notice: before using the screwdriver, its head must be
wrapped with adhesive strap,
ten clipes (d) Tear down the door interior trim panel.
electric indoor plate (Dr)
(Dr electric)
(a) Tear down the inner clip bolts and inner clip;
(b) Tear down the door lamp bolts and the door lamp;
(c) Tear down the electric switch and its panel; and
(d) Insert the screwdriver into the seam between the fixed
clip and the door interior trim panel to loose the interior
trim panel.
ten clipes
(f) Tear down the door interior trim panel.
electric indoor plate(SL. SK. SL)

SL SK SY)
(a) Tear down the inner clip bolts and inner clip;
(b) Tear down the electric switch and its panel;
(c) Tear down the screw cap and screw of door interior trim
panel;
(d) Insert the screwdriver into the seam between the fixed
clipes and door interior trim panel to loose the panel.
eight clipes Notice: the head of screwdriver must be wrapped with
adhesive strap when using the screwdriver.
electric indoor plate(SF) (e) Tear down the door interior trim panel.

SF)
(a) Tear down the inner clip bolts and the inner clip;
(b) Tear down the door lamp bolts and the door lamp;
(c) Tear down the electric switch and panel;
(d) Insert the screwdriver into the seam between the fixed
sevenclips clipes and door interior trim panel to loose the panel;
(e) Tear down the door interior trim panel
electric indoor plate(SJ)

SJ)
(a) Tear down the inner clip bolts and the inner clip;
(b) Tear down the electric switch and panel;
(c) Tear down the screw caps and screws of door interior trim
panel;
(d) Insert the screwdriver into seam between fixed clipes and
door interior trim panel to loosen the panel.
sixclips Notice: the screwdriver head must be wrapped with
adhesive strap before using the screwdriver.
(e) Tear down the door interior trim panel.
 Vehicle Body
Rear Door B0-15

4. Tear down the outer auchi

Prize the clipes alongside the edge of paneling to tear down the
outer
5. Tear down the door window glass;(Dr SF SL SK SY SJ)
Tear down the fixing bolts of two glass channels
(a) Pull the glass up to take it down.
(b) Pull the glass downwardly to take it down after disassem-
bling the tail door lower baffle and lower dust strip (Dr)

6. Tear down the upper glass guide track (SF)

Tear down the bolts and guide track.
7. Tear down the lower rear glass guide track (Dr SF);
Tear down the bolts and guide track.

8. Tear down the quarter window glass (SF SJ)

SF

SJ 9. Tear down the door glass channel

10. Tear down the glass elevator(Dr SF SL SK SY)

(a) Tear down the two fixing bolts of small sliding track.
(b) Tear down the fixing bolts of three elevators (manually
operated)
(c) Disassemble the elevator through auxiliary hole.
B0-16 Vehicle Body
Rear Door

SJ (SJ)
(a) Tear down the four fixing bolts of elevator bracket;
(b) Tear down fixing bolts of three elevators;
(c) Disassemble the elevator through the auxiliary hole.

11. Tear down the lock ring inside the vehicle;

Disconnect the connecting bar to tear down the lock ring inside
vehicle body.
12. Tear down door lock and the outdoor handle with lock
barrel:
(a) Disconnect the outdoor with lock barrel from the con-
necting bar.
(b) Tear down three screws and door lock.
(c) Tear down the two bolts and the outdoor handle with lock
barrel.
(d) Tear down the spring snapping ring and lock barrel.

Dr Change of Glass
a:35mm
(Dr SF)
1. Tear down the glass bracket with screwdriver or similar
tool.
2. Coat the black glue on the inner side of glass bracket
a
liner.
3. Tap the glass bracket with rubber hammer to encase it.

Tear down the bolts on gear panel with the pliers or similar
SF
b:80mm(manual) tool.
65mm(electric)

4. Tear down the bolts of door window glass bracket to take the
glass out.
 Vehicle Body
Rear Door B0-17

Assembly of rear door

1. Coat the MP lubricant on the parts before mounting
(a) Coat the MP lubricant on the sliding face and gear of
glass elevator;
Notice: Do not coat the MP lubricant on the spring of
glass elevator.
(b) Coat the MP lubricant on the sliding face of door lock.

SJ

2. Mount the outdoor handle with lock barrel and door lock:
(a) Mount the lock barrel on the outdoor handle with spring
snapping ring.
(b) Mount the outdoor handle and the lock barrel with two
bolts;
(c) Mount the lock door with three screws; and
(d) Connect the connecting bar to the outdoor handle.
3. Mount the inside lock ring
Mount the inside lock ring and connect the connecting bar.
4. Mount the glass elevator:
(a) Put in the elevator through the auxiliary hole;
(b) Mount three fixing bolts of elevator (for manually-
operated elevator);
Mount four fixing bolts of elevator (for electric elevator)
(c) Mount the small sliding track and tighten the fixing bolts
temporarily;

SJ (SJ)
(a) Put in the elevator through the auxiliary hole;
(b) Mount three fixing bolts of elevator;
(c) Mount four fixing bolts of elevator bracket.
B0-18 Vehicle Body
Rear Door

SF 5. Mount the door glass channel;

6. Mount on the quarter window glass (SF SJ)

7. Mount the upper glass guide track (SF)

Mount the bolts and guide track.

SJ

8. Mount lower rear glass guide track (Dr SF)

Mount the bolts and guide track.
9. Mount the door window glass;
(Dr SF SL SK SY SJ)
Put the glass in the door cavity and then fix the glass on the
glass elevator with two bolts.
Mount on the tailgate baffle and lower dust strip (Dr)

10. Adjust the door window glass

Adjust the balance arm upwardly or downwardly until the
dimensions A and B shown in the drawing are equal, and then
fix the balance arm.
A=B
A B
11. Mount the outerauchi

12. Mount the door interior trim panel;

13. Mount the indoor handle:

(a) Push the indoor handle in the door paneling and slide it
backwardly.
(b) Tighten the screws.
 Vehicle Body
Rear Door B0-19

14. Mount the elevator handle (Dr)

30

Mount the paneling and elevator handle with spring snapping
ring as shown in the drawing under the condition that the all
forward
of doors and windows of vehicle are closed.
B0-20 Vehicle Body
Adhesive Strip On Body Collision Avoidance

Adhesive strip of body collision avoidance

Notices on storing the adhesive strip of body collision avoidance:

1. The adhesive strip should be stored in the cool shadow place where can avoid the direct lighting of sun,
the high temperature and the dust.
2. As the adhesive strip is the PVC product, do not make it touch the paint thinner, other solvents and the
boiling water.
3. The limit storage period of adhesive strip is 9 months.

Element figure

exterior adhesive exterior adhesive

strip at front door strip at rear column

exterior adhesive exterior adhesive exterior adhesive

strip on wing panel strip at tailgate strip at rear body
Vehicle Body
Adhesive Strip On Body Collision Avoidance B0-21

Disassembly of adhesive strip of body

collision avoidance
1. Tear down the ends of adhesive strip;
Loosen the ends of adhesive strip for 31 mm with the scraper.

2. Tear down the adhesive strip and clear away the adhe-
sive agent;
(a) Cut down the adhesive agent with knife and pull down the
adhesive strip;
(b) Clear away the adhesive agent with knife or abrasive
paper.
Remark: Do not reuse the adhesive strip that is disassembled.

Mount of adhesive strip of body collision

avoidance
1. Clean the mounting face of adhesive strip;
Scrape the feculence with cleaning materials.

2. Heat the adhesive strip;

Heat the new adhesive strip with heating lamp to the 30
60
.
Notice: do not overheat the adhesive strip and the
temperature should not higher than 80
.
3. Pull out the separation paper from the adhesive strip
surface;
Remark: notice should be taken not to let the feculence and
dust enter into when separating the separation paper.

4. Mount the adhesive strip along with the body pinching line.
Mount the adhesive strip along with the body pinching line as
shown in the drawing.
Remark: the convex and concave line of the adhesive strip
should be in consistent with the body pinching line.
Notice:
1. Heat the body and adhesive strip to the moderate
temperature;
2. Press the adhesive strip with thumb and exert
moderate pressure so as to ensure the mount is
fastening.
3. Do not wash the vehicle within 24 hours once the
mount is finished.
B0-22 Vehicle Body
Adhesive Strip On Body Collision Avoidance

Adhesive strip of body collision avoidance (
)

Element mounting position

SL small double-row model

B: 7 mm
C: 3 mm
D:10 mm
E: 4 mm
B C D E

SLbig double-row model

B: 7 mm
C: 3 mm
D:10 mm
E: 4 mm

B C D E

SY

B: 7 mm
C: 3 mm
D:10 mm
E: 4 mm

B C D E
 Vehicle Body
Adhesive Strip OSn Body Collision Avoidance B0-23

Adhesive strip of body collision avoidance (
)

Element mounting position

Drsmall double-row model

A: 2 mm
B: 3 mm
C: 3 mm
D: 3 mm
A B C D E F d E: 6 mm
F: 2 mm
G:18 mm

Drbig double-row model

A: 2 mm
B: 3 mm
C: 3 mm
D: 3 mm
A B C D E F G
E: 6 mm
F: 2 mm
G:18 mm

A C E
B D F
B0-24 Vehicle Body
Wheel-Trims

Wheel-trims
Wheel-trims of stainless steel
Element mounting position
Dr

rear wheel-trims

shield of front wheel

Change of shield of front wheel

1. Tear down the shield of front wheel;
Tear down the five screws to take down the Wheel-trims;
2. Mount the shield of front wheel
(a) Tap the front shield manually to ensure it contact the
body closely.
(b) Mount the five screws.

Change of rear Wheel-trims

1. Tear down the rear Wheel-trims.
Tear down the five screws and take down the Wheel-trims.
Prize up the snapping plate of Wheel-trims with screwdriver to
take down the Wheel-trims (SF)
2. Mount the rear Wheel-trims:
(a) Tap the rear Wheel-trims manually to ensure it contacts
the body closely.
(b) Mount the five screws.
Clamp the Wheel-trims with snapping plate. (SF)
 Vehicle Body
Wheel-Trims B0-25

large wheel trims

Element mounting position

SF

shield of front wheel rear wheel-trims

wrapping angle of
shield of front wheel

Change of shield of front wheel and wrapping angle

1. Tear down the shield of front wheel and wrapping angle;
Tear down the seven screws and take down the Wheel-trims.
2. Mount the shield of front wheel:
(a) Mount the adhesive strip of Wheel-trims first, ensure the adhesive
strip contact the Wheel-trims closely;
(b) Mount the five screws.
3. Mount the wrapping angle of the front Wheel-trims.
Mount the wrapping angle on the front bar first, and then fix it with two
screws.
Change of rear wheel-trims
1. Tear down the rear Wheel-trims
Tear down the five screws and take down the Wheel-trims;
2. Mount the rear Wheel-trims
(a) Mount the adhesive strip of Wheel-trims first, ensure the adhesive
strip contact the Wheel-trims closely;
(b) Mount the five screws
B0-26 Vehicle Body
Wheel-Trims Wrapping Angle and Exterior Trim Panel

Wheel-trims wrapping angle and exterior trim panel (
)

Element mounting position

SY

adhesive strip of wheel-trims

rear wrapping angle

rear wheel-trims

front wheel-trims

front wrapping angle

 Vehicle Body
Wheel-Trims Wrapping Angle and Exterior Trim Panel B0-27

Wheel-trims wrapping angle and exterior trim panel (
)

Element mounting position

Top-grade SY

trim panel at rear door

rear wheel-trims

luminous channel

rear wrapping angle

front wheel-trims

trim panel at front door

front wrapping angle

B0-28 Vehicle Body
Wheel-Trims Wrapping Angle and Exterior Trim Panel

Wheel-trims wrapping angle and exterior trim panel (
)

Element mounting position

SJ

rim panel at rear door

rear wheel-trims

front wheel-trims

rear wrapping angle

front wrapping angle

trim panel at front door
 Vehicle Body
Wheel-Trims Wrapping Angle and Exterior Trim Panel B0-29

SJ Change of front wrapping angle

1. Tear down the front wrapping angle;
Tear down the three screws and take down the front wrapping
angle and adhesive strip of wrapping angle lightly (there is two
screws in top-grade SY vehicle)

2. Mount the front wrapping angle

(a) Mount on the three screws (mount two screws for top-
grade SY vehicle)
(b) Contact the front wrapping angle with the front bar
closely, and the seam between the front wrapping angle
and the front Wheel-trims should be even with a smooth
transmission (by the way, the adhesive strip of wrapping
angle should be pressed tightly and evenly)

SJ Change of front Wheel-trims

1. Tear down the front Wheel-trims
Tear down the four screws and the pressing plate of mudguard,
and take down the front Wheel-trims and adhesive strip of
Wheel-trims tightly (SY)
Tear down the five screws and the pressing plate of mudguard,
and take down the front Wheel-trims and adhesive strip of
Wheel-trims tightly (SJ)
Tear down the four screws and uncover the lighting channel of
the front Wheel-trims, take down the front Wheel-trims after
tearing down one screw (top-grade SY).
2. Mount the front Wheel-trims
(a) Flush the front end of front Wheel-trims with the lower
edge of wing panel; the adhesive strip of wheel-trims
should be pressed tightly and evenly. (SY)
Flush the front end of front Wheel-trims with the lower
edge of wing panel, the rear end of front Wheel-trims
with rear edge of wing panel. (top-grade SY SJ)
(b) Mount the four screws (five screws for SJ model) and the
pressing plate of mud guard and stick the lighting strip.
(top-grade SY)

SJ Change of trim panel at front door

1. Tear down the trim panel at front door;
Prize up the clip of trim panel at front door and take down the
trim panel at front door. (SJ)
Uncover the luminous strip to tear down the five screws, then
open the front door and take down the trim panel at front door
after tearing down the five screws. (top-grade SY)
B0-30 Vehicle Body
Wheel-Trims Wrapping Angle and Exterior Trim Panel

Top-grade SY 2. Mount the trim panel at front door;

(a) Flush the arc lines of the front and rear ends of trim panel
at front door in consistent with the door waist line, and the
rear end should flush with the rear end of front door, but
the front end should not interfere with the wing panel.
(b) Tap the positions of six clipes of trim panel at front door
manually to mount it on.(SJ)
Mount the five screws at upper part after aligning the
holes, and mount the five screws at lower part from the
inside, then stick the luminous strip. (top-grade SY)

SJ
Change of trim panel at rear door
1. Tear down the trim panel at rear door
Take down the trim panel at rear door after tearing down one
screw and four clipes. (SJ)
Uncover the luminous strip to tear down the four screws, and
then open the rear door to tear down the four screws inside so
as to take down the trim panel at rear door. (top-grade SY)
Top-grade SY

Top-grade SY 2. Mount the trim panel at rear door

Tap the positions of four clipes of trim panel at rear door
manually to mount it on, meanwhile mount the one screw at
upper part of rear edge. (SJ)
Mount the four screws at upper part after aligning the holes,
and mount the four screws at lower part from the inside, then
stick the luminous strip. (top-grade SY)

SJ Change of rear Wheel-trims

1. Tear down the rear Wheel-trims;
Tear down the three screws and take down the rear Wheel-
trims and the adhesive strip of Wheel-trims. (SY)
Take down the rear Wheel-trims after tearing down the three
screws. (SJ)
Tear down the three screws and uncover the luminous strip on
rear Wheel-trims, take down the rear Wheel-trims after tearing
down the two screws. (top-grade SY)

2. Mount the front Wheel-trims

(a) Flush the front end of rear Wheel-trims with the edge line
of rear door, the rear end of the Wheel-trims with the rear
wrapping angle, the seam should be smooth with even
transmission. (top-grade SY SJ)
(b) Mount the three screws (and mount two screws at the
position where the luminous strip is stickled).
 Vehicle Body
Wheel-Trims Wrapping Angle and Exterior Trim Panel B0-31

Top-grade SY Change of rear wrapping angle

1. Tear down the rear wrapping angle;
Tear down the three nuts, one screw and one self-drilling
screw, and then take down the rear wrapping angle, the rear
mudguard and the adhesive strip. (SY)
Tear down the four screws and then take down the rear small
Wheel-trims. (SJ)
Tear down one screw and three bolts to take down the rear
wrapping angle (top-grade SY)
2. Mount the rear wrapping angle
(a) Parallel the rear wrapping angle with the body waist line,
and contact the body with rear bar closely. (the adhesive
strip of wheel trims of SY model vehicle should be
pressed tightly and evenly)
(b) Mount two bolts through the body bracket, wrapping
angle and mudguard, and another bolts should be mounted
to connect the rear bar bracket and the wrapping angle.
Then mount on one screw and one self-drilling screw.
(SY)
Flush the rear small Wheel-trims and the rear Wheel-
trims, then mount on the four screws (SJ)
Mount on one screw and the other three bolts through the
body bracket, rear bar and wrapping angle. (top-grade
SY)
Notice: the parts mentioned above should be carefully
disassemble or assemble to avoid of paint face scrape
B0-32 Vehicle Body
Front Windshield

Front Windshield (
)

Element mounting position
Dr

sealing strip of front windshield

front windshield

luminous strip

front ventilating cover board

wiper arm

SF

front windshield

luminous strip
front ventilating cover board
wiper arm
 Vehicle Body
Front Windshield B0-33

Front windshield (
)

Element mounting position
SL SK SY SJ
upper trim strip of windshield
front windshield

right trim strip of

windshield

left trim strip of windshield

front ventilating cover board ower limit stop-grade

wiper arm

Dismantle of front windshield

1. Tear down the following parts:
(a) The wiper arm;
(b) The front ventilating cover board;

2. Tear down the front windshield;

(a) Use the screwdriver to prize the sealing element from the
sealing strip
body.
Notice: be careful not to damage the paint on body.

vehicle
body
B0-34 Vehicle Body
Front Windshield

(a) Prize the lips of sealing strip from the inside of body
sealing strip flange outwardly;
(b) Pull out the glass to take it down together with the
sealing strip.
(c) Take out the glass from the sealing strip.

In case new sealing strip is used:

(a) Prize the lips of the sealing strip from the inside of body
flange outwardly;
(b) Pull out the glass to take it down;
(c) Tear down the old sealing strip.
Notice: be careful not to damage the body and glass.

Cut a small open in the sealing agent between the glass and the
vehicle body, then insert a steel wire in the open to pull is to and
fro slowly until the sealing agent is separated completely, then
pull out the glass to take it down.
Notice: be careful not to damage the body and glass.

Mount of front windshield

1. Clean the body frame and the glass.
Clear away the sealing agent on the body surface completely,
then clean the contacting face of body and glass with cleaning
materials.

2. Clean the sealing strip;

Clean the sealing strip surface with cleaning materials.

3. Encase the front windshield in the sealing strip (Dr)

(a) Coat the silicon oil around the glass, and mount the
adhesive strip on the glass according to the glass shape.
Notice: if the adhesive is stiffening or deforming, it may
result the water leakage, therefore, change with the
new one where possibly.
(b) Mount a rope alongside the sealing strip groove as
shown in the drawing for operation,(fasten the rope
inside of the adhesive strip, rope diameter:
=4mm)
Vehicle Body
Front Windshield B0-35

4. Mount of front windshield.

Dr
(a) Lay the ready glass against the corresponding position of front
windshield opens.
(b) Pull the rope from the inside of body to encase the roof, the front
column and the door frame within the adhesive strip, meanwhile
push the outside of the glass by hand.
(c) Tap the four edges of the adhesive strip to ensure that the
adhesive strip contact closely with the body windshield opened.
(d) Coat the glue from left to right at the upper part of windshield
(location between the adhesive strip and the body windshield open)
and the lower part of windshield (location between the adhesive
strip and glass), and the remaining glue should be cleared away with
abrasive paper, and the location should be cleaned with cloth.
Notice: there should no breakage at the sealing glue seam
when coating the glue.

SL SK SF SY SJ
(a) Suck the front windshield with two sucking discs and put the
glass on the worktable in reverse dirdction.
(b) Seize the upper trim strip of front windshield at the position of
upper glass edge.
(c) Coat the cleaning active agent on the inside edges around the
front windshield (the black glass edges), airing for 3~5 min, then
coat the priming paint on the layer of cleaning active agent, and
airing for 5 to 30 min, finally coat the sealing agent.

Notice: no breakage should be allowable at the sealing glue

seam when coating.
Recommended sealing agent for use:
(SF)
Glass glue TS-100 PVC windshield glue
Priming paint TS-5028
Cleaning active agent TS-7016
(SL SK SY SJ)
Glass glue TEROSTAT-8590 windshield glue
Priming paint TEROSTAT-8511

(d) Clean the body windshield open completely with cotton cloth to
coat the priming glue, airing for 5 min or so, and then stick the
front windshield to the windshield open.
(e) Fix the left/right trim strip of front windshield at the edges of
windshield open.
(f) Fix the lower trip strip of front windshield with screw at the
clipes of lower glass edge. (SF)
(g) Stick the upper edge of front windshield to the body with
transparent adhesive strip so as to prevent the glass from lowering.
B0-36 Vehicle Body
Front Windshield

Notice:
(a) Clear away the redundant glue from the body
completely.
(b) The vehicle should not be driven after 4 hours in
summer and 8 hours in winter under common
circumstances.

5. Mount the following parts:

(a) Front ventilating cover board;
(b) Wiper arm.

6. Check whether there is leakage and the leakage repara-

tion
(a) Conduct the leakage test.
(b) Seal the leaking parts with vehicle glass glue.
 Vehicle Body
Side-Window Glass B0-37

Side-window glass (
)

Element mounting position
SF

side-window glass

SY

side-window glass

spilling strip
trim strip of side window
B0-38 Vehicle Body
Side-Window Glass

Side window glass (
)

Element mounting position

SJ
side-window glass

spilling strip
trim strip of side
window

Dismantle of side window glass

1. Tear down the following parts:
(a) Lower trim panel of rear column;
(b) Rear side-panel trim
(c) Roof
2. Tear down the side window glass
(a) Tear down the three hex nuts and eight nuts on flange
(SF)
(b) Cut a small open in the sealing glue between the glass and
body with knife, then insert the steel wire into the small
open and pull it fro and to slowly until the sealing glue
between the glass and body separate completely, and pull
the glass out to take it down.
Notice: be careful not damage the body and glass.

Mount of side window glass

1. Clean the body and glass;
Clean the contacting face of body and glass completely with
cleaning materials.
2. Cleaning the sealing strip;
Clean the sealing strip surface with cleaning materials.
 Vehicle Body
Side Window Glass B0-39

3. Mount the trim strip and spilling strip of side window (SY SJ)
(a) Assemble the trip strip of side window on the left upper
conner of inner edge of the left side window at 60 mm under
the conner, and encase the roof in the trim strip.
(b) Stick the spilling strip (4
6) to the center of lower edge of
side window and to the circumference of the glass frame.

SJ 4. Mounting of side glass

Coat the cleaning active agent around the inner edge along the
circumference of side window glass (the black glass edge).
Airing for 3 to 5 min, coat the priming agent on the layer of cleaning
active agent and airing for 5 to 30 min.
(SY
SJ)
(a) Plaster the glass glue with the glue container on the layer of
priming paint of window frame with the initiative location
200 mm under the left upper conner of left side window.
(b) Stick the glass quickly to the window frame and adjust the
SY upper, lower, left and right clearance, and fill them with
gasket.
(c) Exert the pressure of certain degree on the glass circumfer-
ence after adjusting so that the glass contact
Recommended sealing glue for use
Glass glue U-201 windshield glue
Priming paint 130
Cleaning active agent C020
(SF)
SF (a) Plaster the glass glue alongside the complete circumference
of adhesive strip of side window glass, and the glue section
should be similar to tri-angle after coating.
(b) Put the side window glass assembly at the corresponding
location on body, fix the upper edge of side window glass with
three hex nuts and others should be fixed with flange nuts.
Recommended sealing glue for use
Glass glue TS-100 PVC windshield glue
Priming paint TS-5028
Cleaning active agent TS-7016
Notice:
(a) When plastering glue, the glue should be plastered continu-
ously and no breakage is allowable at the sealing glue seam.
(b) Clean the redundant glue on the body;
(c) The vehicle is not allowed to drive within 4 hours in summer
and 8 hours in winder under common circumstances.

5. Check whether there is leakage and the leakage reparation;

(a) Conduct the leakage test;
(b) Seal the leaking parts with glass glue.
B0-40 Vehicle Body
Rear Door Glass

Rear door glass

Element mounting position
SY SJ

rear door glass

trim strip at tailgate

wire harness of
rear defroster

plastic clip
spilling strip

Dismantle of rear door glass

Disconnect the connecting wire of the defroster first, cut a small
open in the sealing agent between the glass and body with knife,
then insert the steel wire into the open and pull the steel wire to
and fro until the sealing glue between the glass and body separates
completely, finally pull the glass outwardly to take it down.
Notice: be careful not to damage the body and glass.

Mount of rear door glass

Seize the wire harness of rear defroster in the plastic clipes
and encase the clipes into the mounting open, then seize the wire
harness of rear defroster in the trim strip at tailgate.
As this mount is the same with that of side window glass, see
the mounting approaches for side window glass.
 Vehicle Body
Rear Windshield B0-41

Rear windshield
Element mounting position

Dr SL SK

rear windshield

sealing strip of rear windshield

Dismantle of rear windshield

sealing strip 1. Tear down the rear windshield:
(a) Prize up the sealing strip front the body with screwdriver.
Notice: be careful not to damage the paint on body.

vehicle
body

(b) Prize the lips of sealing strip outwardly from the inside
sealing strip of the body flange.
(c) Pull the glass outwardly to tear it down together with the
sealing strip.
B0-42 Vehicle Body
Rear Windshield

Mount of rear windshield

1. Clean the body and glass;
Clean the contacting face of body and glass with the
cleaning materials.
2. Clean the sealing strip
Clean the sealing strip with cleaning materials;

3. Mount the rear windshield in the sealing strip

(a) Coat a layer of silicon oil around the glass circumference
and mount the adhesive strip on the glass according to
the glass shape.
Notice: if the adhesive strip becomes stiffening or
deforming that will lead to water leakage, change with
the new one where possibly.
(b) Mount a rope alongside the sealing strip channel as
shown in the drawing (fix the rope in the adhesive strip).
4. Mount the rear windshield
(a) Lay the ready glass against the corresponding position of
rear windshield opens.
(b) Pull the rope from the inside of body to encase the roof,
the rear column and the door frame within the adhesive
strip, meanwhile push the outside of the glass by hand.

(c) Tap the four edges of the adhesive strip to ensure that the
adhesive strip contact closely with the body windshield
opened.
(d) Coat the glue from left to right at the upper part of
windshield (location between the adhesive strip and the
body windshield open) and the lower part of windshield
(location between the adhesive strip and glass), and the
remaining glue should be cleared away with abrasive
paper, and the location should be cleaned with cloth.
Notice: there should no breakage at the sealing glue
seam when coating the glue.
Recommended sealing agent for use
Glass glue XL-1211 acid silicone glass glue
5. Check whether there is leakage and the leakage
reparation;
(a) Conduct the leakage test;
(b) Seal the leaking parts with glass glue.
 Vehicle Body
Cargo Body Baffle B0-43

Cargo body baffle

Element mounting position

Dr SL SK

connecting bar baffle lock controller

2 screws

cargo body
hinge
baffle lock

bolt hole

14
rear panel of cargo body

buffer block
14 screws
14 screws
hinge assembly
inner cover panel (Dr SK)

N
m
specified torque

Dismantle of baffle lock

1. Tear down the inner cover panel.
(SL)
Tear down the 14 screws and the inner cover panel.
(Dr SK)
Tear down the 12 screws and the inner cover panel.
2. Disconnect the connecting bar of baffle lock from the
baffle lock controller.

3. Tear down the baffle slide fastener

(a) Tear down the baffle lock from the baffle.
(b) Tear down the two screws and the baffle lock.

4. Teardown the baffle from the baffle

Teardown the 12 screws and the baffle lock
B0-44 Vehicle Body
Cargo Body Baffle

Mount of Baffle
1. Mount the baffle lock on the baffle;
Mount the baffle lock with two screws (Dr SK)
Mount the baffle lock with two nuts (SL)
2. Connect the connecting bar with the baffle lock controller.

3. Mount the baffle slide fastener;

(a) Mount the baffle slide fastener and bolts.
Fastening torque
14N
m
(b) Connect the baffle slide fastener with the baffle.
4. Mount the baffle hinge on the baffle

5. Mount the inner coverpannel

SL)
Mount the inner cover panel with 14 screws;

Dr SK)
Mount the inner cover panel with 12 screws.

Dismantle of baffle lock controller:

1. Tear down the inner cover panel;
2. Disconnect the two baffle connecting bar;
3. Tear down the baffle lock controller
Tear down the two screws and the baffle lock controller; (Dr
SK)
Tear down the two nuts and the baffle lock controller. (SL)

Mount of baffle lock controller

Mount the baffle lock controller in the reverse order for
disassembly.
 Vehicle Body
Tailgate B0-45

Tailgate (
)
Element figure

SF

tailgate glass

glass supporter

glass bracket
outer auchi

tailgate handle
lock ring

inner auchi

glass elevator at tailgate trim panel at tailgate I

tailgate lock

tailgate cover panel

sealing strip at tailgate

sealing strip at tailgate

B0-46 Vehicle Body
Tailgate

Dismantle of tailgate
1. Tear down the trim panel of the tailgate:
(a) Insert the screwdriver between the fixing clipes and the
trim panel at the tailgate to loose the trim panel.
Notice: the screwdriver should be wrapped at its head
with adhesive strap before using
(b) Tear down the trim panel at tailgate.
2. Tear down the tailgate cover panel;
Tear down the three bolts and the tailgate cover panel.
3. Tear down the tailgate handle and the lock ring:
(a) Tear down the two bolts on handle.
(b) Disconnect the controlling bar from the glass elevator
and tear down the tailgate handle.
(c) Disconnect the controlling bar from the glass elevator to
take down the lock ring.

4. Tear down the trim panel of tailgate I;

Tear down the six bolts and trim panel of tailgate I;

5. Tear down the sealing strip at tailgate;

Tear down the two threaded ends and the sealing strip;

6. Tear down the outer auchi

7. Tear down the glass elevator at tailgate;

(a) Tear down the tailgate glass;
(b) Pull the glass outwardly to take it down.

8. Tear down the tailgate lock;

Tear down the three bolts and the tailgate lock.
 Vehicle Body
Tailgate B0-47

9. Tear down the tailgate lock

Tear down the three screws from the tailgate to tear down the
lock

Change of Glass
1. Tear down the glass bracket with screwdriver or with
similar tool.
120mm 105mm 2. Coat the polyurethane glue, seize the gasket on the
outside glass and coat the glass glue at outside of the gasket.
3. Encase the glass bracket by tapping it with rubber
hammer.

Tailgate Assembly of
Assembly the tailgate in the reverse order of the disassembly
approaches.
Notice: coat the lubricant on the sliding face, elevator
gear and door lock before mounting the parts.
B0-48 Vehicle Body
Tailgate

Tailgate (
)
Element figure

SY SJ

adhesive block

pneumatic ejector rod

tailgate hinge
tailgate assembly
sealing strip

side lower
position limit
side upper
position limit
front wall
plastic clipes plastic clipes
10 screws

trim panel
at tailgate

lock clip
assembly
stop-grade upper position limit
washer
lower
position limit

tailgate lock tailgate lock

nut barrel assembly
Vehicle Body
Tailgate B0-49

Dismantle of Tailgate
1. Tear down the trim panel at tailgate;
Tear down the ten plastic clipes and take down the trim panel
at tailgate.

2. Tear down the tailgate lock barrel and lock from tailgate:
(a) Screw off the nuts of lock barrel from the inside of
tailgate cavity and take down the lock barrel from the
outside.
(b) Tear down the three screws to take down the tailgate lock.
3. Tear down the tailgate lock clip
Take down the tailgate lock clip from the lower beam flange
after tearing down the two screws.

Dismantle of Tailgate
1. Tear down the pneumatic ejector rod;
Tear down the screws and take down the two pneumatic ejector
rod from the tailgate and the body.
2. Tear down the tailgate hinge and the tailgate;
(a) Tear down the eight bolts to take down the right and left
tailgate hinge from the tailgate and the body;
(b) Pull out the plugging element of wire harness to tear
down the tailgate from the body.
3. Tear down the position limit
After tearing down the two bolts, take down the left and right
side upper/lower position limits and the upper/lower position
limit from the tailgate and the body.
Tear down the position limit

Mount of tailgate lock and the tailgate

Mount the tailgate lock and the tailgate in the reverse
order
B0-50 Vehicle Body
Instrument Panel

Instrument panel (
)

Element figure

Dr

instrument
panel body

glove box
cover

glove box

lower instrument cover

left air tunnel

combination
instrument

ignition
switch cap
upper instrument
cover central cover

air-conditioning
controlling
mechanism
assembly
decorative cover of
instrument
air passage

CD device

central lower wall

ashtray
 Vehicle Body
Instrument Panel B0-51

Instrument Panel (
)

Element figure

SF

instrument panel body

fixed bracket

glove box

central air tunnel

lower instrument cover

central switch

central panel

combination instrument ir-conditioner panel

instrument cover

combined acoustic
cigarette lighter seat device

ashtray
B0-52 Vehicle Body
Instrument Panel

Instrument panel (
)

Element figure

SL SK SY SJ

instrument
panel body

right upper air tunnel

central air tunnel

decorative cover
of instrument lower covering board
combination at right end
instrument

glove box
left upper
air tunnel

glove box lock

lower instrument
cover(SY)

lower instrument cover

CD device

central cover

ashtray cluster

air-conditioning
controlling mechanism
assembly cigarette
lighter seat

lower decorative
frame of
instrument panel
Vehicle Body
Instrument Panel B0-53

Dismantle of instrument panel

(Dr SF)
1. Disconnect
E
F the cable of accumulator from the negative
polar;
2. Tear down the steering wheel;
3. Tear down the combined switch shell cluster;
4. Tear down the bonnet lock switch;
Tear down the two screws and the sliding fastener of bonnet
lock.
5. Tear down the central bottom-wall (Dr)
Tear down the decorative cover of gearbox (SF)
6. Tear down the instrument cover (SF).
Tear down the two screws and the cover.

7. Tear down the lower instrument cover;

(a) Tear down the ignition lock;
(b) Tear down the five screws and the cover;
Tear down the four screws and the cover;
(c) Disconnect the plugging elements.

8. Tear down the air-conditioner controlling panel;

(a) Pull out the air-conditioner controlling button;
(b) Prize out the A/C switch;
(c) Prize out the air-conditioner panel as shown in the
drawing with screwdriver and take it down.
Notice: the screwdriver should be wrapped with adhesive
strap at its head before using.
(d) Disconnect the plugging elements.

9. Tear down the decorative cover of instrument (Dr)

(a) Tear down the two screws to pull out the decorative cover
of instrument;
(b) Disconnect the plugging elements.
B0-54 Vehicle Body
Instrument Panel

10. Tear down the combination instrument;

(a) Tear down the four screws;
Tear down the two screws;
(b) Disconnect the plugging elements;
(c) Tear down the combination instrument.

11. Tear down the ashtray cluster;

12. Tear down the central cover;

(a) Tear down the decorative frame;
(b) Tear down the three screws to pull out the central cover;
(c) Disconnect the plugging elements.

13. Tear down the central panel;

(a) Prize out the central panel as shown in the drawing with
screwdriver to take it down.
Notice: the screwdriver must be wrapped with adhesive strap
at its head before using.
(b) Disconnect the plugging elements.
14. Tear down the air-conditioning controlling mechanism
assembly;
Tear down the two screws, which will let the air-conditioning
controlling mechanism in suspension.
15. Tear down the air-controlling panel;
(a) Tear down the four screws to pull out the air-condition-
ing panel;
(b) Disconnect the plugging element;
16. Tear down the CD device or the combined acoustic
device;
(a) Tear down the four screws.
(b) Disconnect the aerial cable and the plugging elements.
(c) Tear down the CD device or the combined acoustic device.
17. Tear down the glove box;
Tear down the two screws and the glove box.
SF
Seize the flanges at two ends of glove box into the sliding
channel of the glove box.
18. Tear down the central air tunnel;
Tear down the four screws and the central air tunnel.
Vehicle Body
Instrument Panel B0-55

19. Tear down the instrument panel body;

(a) Tear down the three screws and the instrument panel.
(b) Disconnect the plugging elements.
SF:
(a) Tear down the fixing bolts at the ends of instrument panel
body to pull out the fixed clipes at the front end.
(b) Disconnect the plugging elements.

SL SK SJ SY
1. Disconnect the cable of accumulator from the negative
polar (-):
2. Tear down the steering wheel;
3. Tear down the combined switch shell cluster;
4. Tear down the bonnet lock switch;
Tear down the two screws and the sliding fastener of bonnet
lock.

5. Tear down the lower instrument cover;

6. Tear down the lower decorative frame of the instrument

panel;
Prize out the decorative frame of instrument with screwdriver
and take it down.
Notice: the screwdriver must be wrapped with adhesive
strap at its head before using.
7. Tear down the decorative cover of instrument;
(a) Tear down the three screws to pull out the decorative
cover of instrument.
(b) Disconnect the plugging elements.

8. Tear down the ashtray cluster;

9. Tear down the central cover;

(a) Tear down the three screws to pull out the central cover;
(b) Disconnect the plugging elements
B0-56 Vehicle Body
Instrument Panel

10. Tear down the combination instrument;

(a) Tear down the four screws;
(b) Disconnect the plugging elements.
(c) Tear down the combination instrument.

11. Tear down the CD or combined acoustic device;

(a) Tear down the four screws;
(b) Disconnect the aerial cable and the plugging elements;
(c) Tear down the CD or the combined acoustic device.

12. Tear down the central air tunnel;

Tear down the four screws to take out the central air tunnel.

13. Tear down the air-conditioner controlling panel;

(a) Pull out the air-conditioner controlling button;
(b) Prize out the A/C switch;
(c) Prize out the air-conditioner controlling panel as shown
in the drawing with screwdriver and take it down.
Notice: the screwdriver should be wrapped with adhesive
strap at its head before using.
(d) Disconnect the plugging elements.
14. Tear down the air-conditioning controlling mechanism
assembly;
Tear down the two screws and let the air-conditioner control-
ling mechanism in suspension.
15. Tear down the lower covering board at right end;
Tear down the four screws and take out the lower covering
board at right end.
16. Tear down the glove box;
Tear down the two screws and the glove box
17. Tear down the instrument body;
(a) Tear down the three bolts and the instrument panel;
(b) Disconnect the plugging elements.

Mount of instrument panel

Mount the parts of instrument panel in the reverse
approach.
 Vehicle Body
Safety Belt B0-57

Safety belt (
)

Element figure

Dr SL SK SF SY SJ front safety belt

43

43

43

43

SF rear safety belt

43

43

43

QP

N
m
specified torque

B0-58 Vehicle Body
Safety Belt

Safety belt (
)

Element figure

safety belt in
SY model
vehicle

43

43
43

43

safety belt in SJ
model vehicle

43

QP

43

QP

N
m
specified torque

Body
Safety Belt B0-59

Safety belt
1. Driving test (in the security place);
(a) Fix the safety belt of the front seat.
(b) Drive the vehicle at the speed of 16 km/h and brake it
suddenly;
(c) Check the safety belt, which should be lock tightly
without expansion.
Remark: it is required to tear down the mechanism
fittings of the safety belt to make the following static load
test at the security place, in addition, moderate inspection
for the new safety belt should be conducted before
mounting no matter when the new safety belt fittings is
needed to mount.
2. Static test

a) Tear down the lock-type expansion fittings;
(b) Tilt the expansion fittings slowly;
(c) Check the expansion of safety belt, which should be
pulled out when the tilt angle is no more than 15 but not
be pulled out when the tilt angle is more than 45

.
If the requirement is not met, change the safety belt fittings.

Two-point safety belt

(manually operated)
(a) Adjust the safety belt to the moderate length;
(b) Exert the stable load on the belt;
(c) Check whether the safety belt is elongated or not, in such
case, the belt should not be elongated.
B0-60 Vehicle Body
Seat

Seat (
)
Element figure

Dr SL SK SF SY SJ
front seat

37

37

37

37
seat in SY
model vehicle

18

18

18

18
N
m
specified torque
 Vehicle Body
Safety Belt B0-61

Safety belt (
)

Element figure

Dr rear seat

18

18

18 SL rear seat

18

18

SY small seat 18

18

N
m
specified torque 18

B0-62 Body
Seat

Seat (
)
Element figure

SF rear seat

18

18

SJ rear seat

18

18

18
18

18
18

N
m
specified torque

 Vehicle Body
Spoiler B0-63

Spoiler (
)
Element figure

SF

highly mounted stop-grade lamp

spoiler

spoiler supporter

Dismantle of Spoiler
1. Tear down the spoiler assembly;
(a) Tear down the four bolts and the spoiler;
(b) Tear down the three bolts and the spoiler supporter.
2. Tear down the wire harness of highly-mounted stop-
grade lamp and take it down;

Mount of spoiler
Mount the spoiler in the reverse approach.
B0-64 Vehicle Body
Spoiler

Spoiler (
)
Element figure

SY SJ

highly mounted
spoiler
nut stop lamp
assembly

spoiler gasket

Spoiler disassembly
1. Tear down the highly-mounted stop-grade lamp;
(a) Tear down the two screws and disconnect the wire harness
from lamp.
(b) Tear down the highly-mounted stop lamp from the spoiler.
2. Tear down the spoiler assembly
(a) Tear down the rear beam trim panel from the inside of body.
(b) Tear down the four nuts and disconnect the wire harness
from the spoiler;
(c) Tear down the spoiler assembly and spoiler gasket from the
outside.
SJ
(a) Open the two covers of round hole at the top-grade of
spoiler;
(b) Tear down the two bolts and disconnect the wire harness
from the spoiler.
(c) Tear down the spoiler assembly and spoiler gasket from the
outside.

Mount of Spoiler
Mount the spoiler in the reverse approach.
 Vehicle Body
Luggage Rack B0-65

Luggage rack
Element figure

SF SY

adjusting button of antiskid strip

blanking plug of
fixed bracket
main sill

beam

bracket fastening
button main sill

antiskid strip

SJ

luggage rack assembly

mounting plate of outer

luggage rack
adhesive strip of mounting plate
B0-66 Body
Reserve Tire Bracket

Reserve tire bracket (
)

Element figure

SY

buffer block bracket

buffer block
lock clip bracket
reserve tire holder assembly

90

adjusting arm

reserve tire lock reserve tire bracket return spring

SJ

reserve tire lock

reserve tire holder

lock clip bracket assembly

90

adjusting arm
reserve tire bracket
N
m
specified torque
K
 Vehicle Body
Reserve Tire Bracket B0-67

Reserve tire bracket (
)

Element figure

SF

springy welt
reserve tire bracket trim cover of fixed bracket

decorative cover of screw hole

nut buffer block

Dismantle of reserve tire bracket

1. Tear down the trim cover of fixed bracket;
Tear down the decorative cover of screw hole, and then tear down the
trim cover of fixed bracket.
Tear down the adjusting arm (SY SJ)
Tear down the two bolts to take down the adjusting arm;
2. Tear down the reserve tire bracket;
Tear down the three bolts and take down the reserve tire bracket. (SF)
Tear down the three bolts and take down the reserve tire bracket. (SY
SJ)

Mount of reserve tire bracket

1. Mount the reserve tire bracket;
(a) Stick the springy welt on the corresponding face where the
reserve tire bracket contact with the body; (SF)
(b) Fix the reserve tire bracket on the body with eight bolts (SF).
Fix the reserve tire bracket with three bolts on the right mail sill
and tail beam of the body.
2. Mount the trim cover of fixed bracket;
Mount the trim cover of fixed bracket and the decorative cover of
screw hole.
Mount the adjusting arm (SY SJ)
Fix the adjusting arm on the tail beam bracket of the body by screwing
the two bolts in the fixing hole.
Notice: the paint layer should be well protected during
disassembling and assembling.
B0-68 Vehicle Body
Body Dimension

Body Dimension
Large lamp seat (
)

Dr
(point Size in 3D)

A 573 a

603

B 573 b

c
`

SF
(point Size in 3D)

A 573 a

623

B b
573

C c

Mark Name Bore diameter Mark Name Bore diameter

A,a Radiator mounting hole M8

B,b Radiator mounting hole M8

C,c Cab mounting hole
10
20

 Vehicle Body
Body Dimension B0-69

Body Dimension
Large lamp seat (
)

SL SY
(point Size in 3D)

A 802 a

B 969 b
1406

C 633 c
D d

E e

SK SJ
(point Size in 3D)

F,f

B b
799

465

E e

G,g

Mark Name Bore diameter Mark Name Bore diameter

A,a Radiator mounting hole
F,f Mounting hole of median mesh

Vertical projection spot of lower
B,b Fixing bolts of front bar
G,g beam of radiator

C,c Fixing bolts of front bar

D,d Radiator mounting hole

E,e Cab mounting hole

B0-70 Vehicle Body
Body Dimension

Body Dimension
Engine Room (
)

Dr SF
(point size in 3D)

J j

H 1005 h
582

K k
1268
I á 384

L l

SL SY
(point size in 3D)

M m

728 728

Remark: the deviation

N n in length of diagonal
line of engine room
should not be more than
4 mm.

Mark Name Bore diameter Mark Name Bore diameter

Locating hole of upper part of
H,h Front locating hole of mudguard M8 M,m front wall
7

I,i Hole of fixing nut of large lamp M8 N,n First mounting hole of wing panel

J,j Front locating hole of mudguard M6

K,k First mounting hole of engine cover M6

L,l First mounting hole of wing panel
10

 Body-Body Dismension B0-71

Body Dimension
Engine Room (
)

SK SJ
(point size in 3D)

O,o
M m

845

711 711

P,p
N n

Remark: the deviation in length

of diagonal line of engine room
should not be more than 4 mm.

Mark Name Bore diameter Mark Name Bore diameter

M,m Hole of fixing nut of large lamp
7

N,n First mounting hole of engine cover

O,o Vertical face of median mesh

P,p Projection line of vertical face of

median mesh
B0-72 Vehicle Body
Body Dimension

Body Dimension
Wind tunnel

Dr SF
(point size in 3D)

*1: Dr 1159
Q *1 q SF 1155
*2: Dr 1370
SF 1373
*2 *3: Dr 589
*3
SF 692
*4: Dr 1327
SF 1333
R *4 r

SL SK SY
(point size in 3D)

S s
U 1210 u
V 1207 v

710 710

W 1440 w
T t

Mark Name Bore diameter Mark Name Bore diameter

Connecting part of top-grade cover Conner spots along outer edge of
Q,q and exterior plate of front pillar
V,v top-grade cover

Connecting part of upper front wall Outer spots of top-grade water
R,r and exterior plate of front pillar
W,w channel

Conner spots along outer edge of
S,s top-grade cover

Mounting hole on cover plate of
T,t front windscreen

Outer spots of top-grade water
U,u channel

 Vehicle Body
Body Dimension B0-73

Body Dimension
Rear Wall (
)

Dr
(point size in 3D)

A
B
a

305 319 305

C
b
c

D
d

200 200

SL SK
(point size in 3D)

G
g

E
e

319 319

H
270 F
f
270 h

I
i

1646

Mark Name Bore diameter Mark Name Bore diameter

Connecting spot on outer panel of
A
,a
0spots on cover ====
F
,f
rear pillar ====

Technique notch on top-grade Corresponding spots of upper edge
B
,b
cover ====
G
,g
of rear wind channel ====

Corresponding spots on rear wall Corresponding spot of waist line
C
,c
panel ====
H
,h
of outer panel of rear pillar ====

Connecting spot on outer plate of Corresponding spots of lower
D
,d
rear pillar ====
I
,i
edge of rear wind channel ====

E
,e
Outer edge of rear wall panel ====

B0-74 Vehicle Body
Body Dimension

Body Dimension
Rear Wall (
)

SF
(point size in 3D)

J
j

1022

1202
376

K
k

1270

SY SJ
(point size in 3D)

L
1141 l

O
o Q
q

900 1042
M
1376 m

N
GN n

P
p
*1: SY 1376
R
r SJ 1385

Mark Name Bore diameter Mark Name Bore diameter

Connecting part of outer panel of
J
,j
rear wall with roof
O
,o
Corresponding spots of upper edge

Lower edge of outer panel of rear Vertical corresponding spot of
K
,k
wall
P
,p
floor

L
,l
Lines and angle of rear side wall
Q
,q

M
,m
Upper angle of rear lamp cavity
R
,r
Outer edge of lock box at tailgate

N
,n
Lower angle of rear lamp cavity

 Vehicle Body
Body Dimension B0-75

Body Dimension
Side wall (
)

Dr
(point size in 3D)

b
b c
c

a
a

1012
629
732
983

970 d
d
h
h
786
886
g
g f
f e
e

SF
(point size in 3D)

b
b c
c

a
a
1009
650
732 1001

973
h
h d
d
913
889
g
g e
e
f
f

Mark Name Bore diameter Mark Name Bore diameter

Technical notch on outer panel of Technical notch on outer panel of
a
,a front pillar
f
,f lower side beam

Technical notch on outer panel of Technical notch on of lowwer
b
,b upper side beam
g
,g beam of outer panel

Technical notch on outer panel of Technical notch of outer panel of
c
,c upper side beam
h
,h middle pillar

Locating hole/technical notch on
d
,d outer panel of rear wall
10
Central mounting hole of rear door
e
,e hinge
8
B0-76 Vehicle Body
Body Dimension

Body Dimension
Side wall (
)

SL SK
(point size in 3D)

j
j k
k
i
i
650
p
p

1138
1138
q
q
1108 =TUR l
l

o
o n
n m
m

SY
(point size in 3D)

j
j k
k

i
i
1108 650 p
p

1063 1063

r
r l
l
1160 785
q
q

n
n m
m

Mark Name Bore diameter Mark Name Bore diameter

Technical notch on outer panel of Technical notch on outer panel of
i
,i front pillar
n
,n lower side beam

Technical notch on outer panel of Technical notch on outer panel of
j
,j upper side beam
o
,o lower side beam

Technical notch on outer panel of Corresponding spot of outer panel
k
,k upper side beam
p
,p of middle pillar

Corresponding spot of outer panel Wiring hole of outer panel of
l
,l of rear pillar
q
,q middle pillar

Technical notch on outer panel of Technical hole on outer panel of
m
,m lower side beam
r

,r front pillar

 Vehicle Body
Body Dimension B0-77

Body Dimension
Side wall(
)

SJ
(point size in 3D)

s
s u
u

r
r
646
t
t

1080
1080

z
z
1110 965 v
v
x
x

y
y w
w

Mark Name Bore diameter Mark Name Bore diameter

Technical notch on outer panel of Corresponding spot of outer panel
r

,r front pillar
w
,w of lower side beam

Technical notch on outer panel of Corresponding hole of outer panel
s
,s
x
,x of middle pillar

upper side beam
Corresponding spot of outer panel Corresponding spot of outer panel
t

,t of middle pillar
y
,y of lower side beam

Corresponding spot on outer panel Technical hole on outer panel of
u
,u of upper side beam
z
,z front pillar

Corresponding spot of outer panel
v
,v

of rear pillar
 B0-78

size in 2D

front
Body
Size of Chasis

Small single-row Deer

assuming
standard line

central line of front wheel

2615 Axial spacing: 2615 Unit
mm

Mark Name Bore diameter Mark Name


A,a Cab mounting hole

E,e Cab mounting hole


B,b Cab mounting hole

F,f Cab mounting hole


C,c Cab mounting hole

G,g Cab mounting hole


D,d Mounting hole of cargo passage









size in 2D

front
Body
Size of Chasis

big single-row Deer

assuming
standard line
central line of front wheel

Axial spacing
2960 Unit
mm

Mark Name Bore diameter Mark Name Bore diameter
A,a Cab mounting hole

E,e Mounting hole of cargo passage


B,b Cab mounting hole

F,f Mounting hole of cargo passage


C,c Cab mounting hole

G,g Mounting hole of cargo passage


D,d Mounting hole of cargo passage
B0-79

 B0-80

size in 2D

front
Body
Size of Chasis

One and half row deer

assuming
standard line
central line of front wheel

Axial spacing
3085 Unit
mm

Mark Name Bore diameter Mark Name Bore diameter
A,a Cab mounting hole

E,e Mounting hole of cargo passage


B,b Cab mounting hole

F,f Mounting hole of cargo passage


C,c Cab mounting hole

G,g Mounting hole of cargo passage


D,d Mounting hole of cargo passage









size in 2D

front
Body
Size of Chasis

Small double-row Deer

assuming
standard line

central line of front wheel

Axial spacing: 2615 Unit
mm

Mark Name Bore diameter Mark Name Bore diameter
A,a Cab mounting hole

E,e Mounting hole of cargo passage


B,b Cab mounting hole

F,f Mounting hole of cargo passage


C,c Cab mounting hole

G,g Mounting hole of cargo passage


D,d Mounting hole of cargo passage
B0-81

 B0-82

size in 2D

front
Body
Size of Chasis

Middle double-row Deer

assuming
standard line

central line of front wheel

Axial spacing: 2615 Unit
mm

Mark Name Bore diameter Mark Name Bore diameter
A,a Cab mounting hole

E,e Mounting hole of cargo passage


B,b Cab mounting hole

F,f Mounting hole of cargo passage


C,c Cab mounting hole

G,g Mounting hole of cargo passage


D,d Mounting hole of cargo passage









size in 2D

front
Body
Size of Chasis

Big double-row Deer

assuming
standard line

central line of front wheel

Axial spacing:
3380 Unit
mm

Mark Name Bore diameter Mark Name Bore diameter
A,a Cab mounting hole

E,e Mounting hole of cargo passage


B,b Cab mounting hole

F,f Mounting hole of cargo passage


C,c Cab mounting hole

G,g Mounting hole of cargo passage


D,d Mounting hole of cargo passage H,h Mounting hole of cargo passage
B0-83

 B0-84

size in 2D

front
Body
Size of Chasis

Small double-row Sailor

assuming
standard line

Central line of front wheel

Axial spacing
3025 Unit
mm

Mark Name Bore diameter Mark Name Bore diameter
A,a Cab mounting hole

E,e Mounting hole of cargo passage


B,b Cab mounting hole

F,f Mounting hole of cargo passage


C,c Cab mounting hole

G,g Mounting hole of cargo passage


D,d Mounting hole of cargo passage









size in 2D

front
Body
Size of Chasis

big double-row Sailor

assuming
standard line

central line of front wheel

Axial spacing
3380 Unit
mm

Mark Name Bore diameter Mark Name Bore diameter
A,a Cab mounting hole

E,e Cab mounting hole


B,b Cab mounting hole

F,f Cab mounting hole


C,c Cab mounting hole

G,g Cab mounting hole


D,d Cab mounting hole H,h Cab mounting hole
B0-85

 B0-86

size in 2D

front
So Cool
Body
Size of Chasis

assuming
standard ling

central line of front wheel

Axial spacing
3025 Unit
mm

Mark Name Bore diameter Mark Name Bore diameter
A,a Cab mounting hole

E,e Mounting hole of cargo passage


B,b Cab mounting hole

F,f Mounting hole of cargo passage


C,c Cab mounting hole

G,g Mounting hole of cargo passage


D,d Mounting hole of cargo passage









size in 2D

front
Safe
Body
Size of Chasis

assuming standard
line

central line of front wheel

Axial spacing
2630 Unit
mm

Mark Name Bore diameter Mark Name Bore diameter
A,a Cab mounting hole

E,e Cab mounting hole


B,b Cab mounting hole








C,c Cab mounting hole








D,d Cab mounting hole
B0-87

 B0-88

size in 2D

front
Sing
Body
Size of Chasis

assuming
standard line
central line of front wheel

Axial spacing
3025 Unit
mm

Mark Name Bore diameter Mark Name Bore diameter
A,a Cab mounting hole

E,e Cab mounting hole


B,b Cab mounting hole

F,f Cab mounting hole


C,c Cab mounting hole






D,d Cab mounting hole







size in 2D

front
Pegasus
Body
Size of Chasis

assuming
standard line
central line of front wheel

Axial spacing
2760 Unit
mm

Mark Name Bore diameter Mark Name Bore diameter
A,a Cab mounting hole

E,e Cab mounting hole


B,b Cab mounting hole






C,c Cab mounting hole






D,d Cab mounting hole
B0-89

 A-1

Specifications of Maintenance
and Up-keeping
page

Clutch .......................................................................... A-2

Gear box ..................................................................... A-2
Transfer box ................................................................ A-3
Drive shaft ................................................................... A-4
Suspension system and automobile axle .................... A-4
Braking system ............................................................ A-5
Steering system .......................................................... A-6

A
A-2 Specification of Maintenance and Up-Keeping
Clutch and Gearbox

Clutch
Specification
Unit
ãã
Item Applicable vehicle model Specification
Pedal height (calculated from front wall Dr SF 160
SL SK SY SJ 190-200
Pedal free stroke Dr SF SL SK SY SJ 5-15
Min depth of clutch-facing rivet Dr SF SL SK SY SJ 0.3
Max radial swing difference of clutch rib Dr SF SL SK SY SJ 0.8
Max radial swing difference of flywheel Dr SF SL SK SY SJ 0.2
Max width of wear of diaphragm spring Dr SF SL SK SY SJ 0.6
Max width of wear of diaphragm spring Dr SF SL SK SY SJ 5
Alignment degree of diaphragm spring end Dr SF SL SK SY SJ Max misplacement
0.5

Torsion moment
Fastening location Applicable Vehicle model (N*m)
Fastening torque for clutch tube on master cylinder Dr SF SL SK SY SJ 15-17
Fastening torque for clutch tube on wheel-brake cylinder Dr SF SL SK SY SJ 15-17
Fastening torque for clutch pressure plate Dr SF SL SK SY SJ 30

Gearbox
Three-grade maintenance for gearbox
1. Grade I maintenance for gear box
Grade I maintenance: Check the lubricant level to see whether the lubricant level is in alignment with the lower edge of oil
filler; if the lubricant is lower than the oil filler lower edge, add the lubricant; or the insufficient lubricant will lead to the poor
lubrication or burn-out of bearing and teeth; while the over-high lubricant will cause the overheating and oil leakage.
2. Grade II maintenance for gear box
Grade II maintenance: The gear box of a new vehicle should be maintained by exchanging the lubricant during the
first grade II maintenance and should be washed with kerosene; and the lubricant quality should be checked in the
grade II maintenance in later time, if the lubricant is diluted, gumming or over-dirty, it should be changed.
3. Grade III maintenance
The gearbox should be disassembled for inspection, washing and oil change.
Notice: As the new vehicle is in the running-in status, the gearbox should be maintained by exchanging lubricant
after the vehicle covers 1500 km,Lubricant Type
GL-5 SAE80W/90

Torsion moment of relative connecting elements

Tung Teeth: Tang tooth(5DYA4TWD
5DYA8FWD)

Fastening location N*m

Locating screw of fork axle at first and second gear 13
17
Locating screw of yoke block 15
20
Screw on baffle of rear bearing of output shaft 17
22
Screw of reverse idler shaft 17
20
Bolt of gearshift cover 15
20
Bolt of front cover 15
20
Bolt of rear body 30
45
Bolt of clutch shell 30
45
Bolt of locating spring 17
22
 Specification of Maintenance and Up-Keeping
Transfer Box A-3

Fastening location N*m

Oil filling/draining plug 30
50
Location mechanism cluster 30
50
Pillar of clutch toggle fork 30
50
Bolt on odometer pressure plate 10
15
Reverse gear switch assembly 30
50

Upper tooth(JK72TWD)
Fastening location N*m
Toggle fork at first, second and fifth gears and the screw of 15
20
toggle fork
Bolt on odometer pressure plate 10
15
Screw on baffle of rear bearing of output shaft 12
17
Screw on baffle of reverse idler shaft 15
20
Locating screw of gearshift yoke block 15
20
Bolt of front cover 15
20
Bolt of gearshift cover 15
20
Pillar of clutch toggle fork 30
40
Bolt of clutch cover 60
70
Bolt of rear body (M10X1.25X130) 30
40
Bolt of rear body (M10X1.25X80) 30
40
Plug of locating spring 17
22
Oil filling/draining plug 30
50
Reverse gear switch assembly 20
40
Location mechanism cluster 30
40
Locking nut at rear end of countershaft 90
125

Maintenance and Up-keeping of Transfer Box

1. The oil level of transfer box should be checked when exchanging the engine lubricant or the vehicle
covers more than 8000 km
and add the lubricant where necessary.
2. Change with the appointed lubricant each year or after the vehicle covers more than 48000 km.
Notice: lubricant brand: 85W/90 GL-5.
Fastening torque of relative connecting elements
Fastening location N*m

Flange nut 203
244

Oil drain plug 19
30
Bolt of motor clip 8
11
Fixing bolt of motor 8
11
Clutch coil nut 8
11
Housing bolt 27
46
Oil pump bolt 4.0
8.5
Venting valve 8
19
Bolt of front connecting body 27
46
A-4 Specification of Maintenance and Up-Keeping
Drive shaft, Suspension System and Automobile Axle

Drive Shaft
Torsion moment
Fastening location Applicable vehicle model N*m
Connecting bolt Dr SF SL SK SY SJ 74
5
Fixing bolt of central supporter Dr SL SK SY SJ 40
5

Suspension System and Automobile Axle

Specification
Item Applicable vehicle model Specification
Inflation pressure of tire Dr SL SK SY SJ Front:220
0kPa
Back:240
0kPa
SF Front:250
0kPa
Back:250
0kPa
Ground clearance of chassis Dr 295mm
SL SK 255
mm
SF 58.5mm(difference in height between
shaft center of lower arm and wheel
center)
SY 310
mm
SJ 295
mm
Steering angle of inner wheel Dr SL SK SY 36
 40

SF
32

SJ 32
 34

Kingpin inner inclination Dr SL SK SY 9
30'
5'
SJ 14
52'
Outer inclination of front wheel
Mechanical steering Dr SL SK SY 0
30'
0'
Power steering Dr 0
10'
0'
SL SK SY 0
20'
0'
SJ 0
20'
5'
Kingpin rear inclination (inclination)
HPM

Mechanical steering Dr SL SK SY 1
50'-20'
Power steering Dr SL SK SY 2
5'
5'
SJ 2
0'
0'
Toe-in Dr SL SK SF SY SJ 0-2mm
Error in length between left and right Dr SL SK SF SY SJ =2mm
drag rod
Side slip value Dr SF =5m/km
SL SK SY SJ
.5m/km
 Specification of Maintenance and Up-Keeping
Braking System A-5

Torsion moment
Fastening location Applicable vehicle model N*m
Limit bolt of steering knuckle SJ 90
10
U-type fixing bolt Dr SL SK SY SJ 110
10
Bolt of spring pin of rear plate and shackle Dr SL SK SY SJ 90
10
Central bolt of rear steel plate spring SL SK SY SJ 50
5
Connecting bolt of rear vibration damper and rear axle SF 64
5
SL SK SY SJ 25
5
Connecting bolt of front vibration damper and lower swing arm SL SK SY SJ 25
5
Connecting bolt of rear vibration damper and frame SF 137
10
Connecting bolt of rear vibration damper and lower swing arm SL SK SY SJ 83
5
Fixing bolt of pedestal arm of torsion rod spring SL SK SY SJ 83
5
Locking nut of torsion rod spring Dr 23
3
SL SK SY SJ 29
5
Fixing bolt at two ends of transverse stabilizer rod Dr SF 23
3
SL SK SY SJ 25
5
Fixing bolt of transverse stabilizer rod bracket Dr SF SL SK SY 96
10
Connection bolt of guide lever and lower arm Dr 150
10
Fixing nut at front end of guide lever Dr SL SK SY SJ 96
10
SF 178
15
Axial fixing nut of front suspension and lower arm Dr 226
25
SF 196
10
Axial fixing nut of lower arm of front suspension SL SK SY 226025
SJ 210025
Connecting nut of steering knuckle and upper ball stud Dr SL SK SY SJ 110
10
SF 142
10
Connecting bolt of steering knuckle and lower ball stud Dr SF SL SK SY SJ 142
10

Braking system
specification
Item Applicable vehicle model specification
Pedal height Dr SF 160mm
SL SK SY SJ 190-200mm
Free stroke of pedal Dr SL SK SF SY SJ 3-6mm
Stroke of operating lever of parking brake Dr 9-10

SL SK SY 7-9

torsion moment
Fastening location Applicable vehicle model N*m
Brake oil pipe Dr SF 18
2
SL SK SY SJ 19
1
A-6 Specification of Maintenance and Up-Keeping
Steering System

Steering system
Specification
Item Applicable vehicle model Specification
Max play of steering wheel Dr SF 6

Tension degree of driving belt:
When f=98N New belt Dr SL SK SF SY SJ 5-7mm
Old belt Dr SL SK SF SY SJ 7-9mm

Torsion moment
Fastening location Applicable vehicle model N*m
Fixing nut of steering wheel Dr SF 50
5
SL SK SY SJ 30
2
Connecting nut of steering ger and swing arm Dr SF 245
25
Fixing bolt of steering driven arm Dr 80
10
SF 142
10
SL SK SY 83
10
SJ 78
10
Fixing bolt of steering gear Dr 96
10
SF 145
10
SL SK SY 96
10
SJ 78
10
Connecting nut of steering drag rod and swing arm of Dr SF 91
10
steering gear
Connecting nut of steering drag rod and steering driven Dr 91
10
arm
SF 59
5
Connecting nut of steering drag rod and front brake Dr SF 91
10
Steering limit bolt SJ 90
10
 B-1

SST Special tool

page

Special tool ................................................................... B-2

B
B-2 SST Special Tool
Special Service Tool

SST Special Service tool

Application position
Diagram Tool name tool number Front axle Rear axle Remark
2WD 4WD
Disassembling and as-
sembling tools for lock-
3916001


ing nut of steering
knuckle

Press fitting tool for in-

ner bearing of front wheel
3916002


hub

Press fitting tool for outer

bearing of front wheel
3916003


hub

Disassembling tool of
ball stud
3916004

Fixing tool of main teeth

flange of needle bearing
3916005

Press fitting tool for steer-

ing knuckle oil seal
3916006

Disassembling tool of
shorter liner of lower arm
3916007

Mounting tool of shorter

liner of lower arm
3916008

Mounting and disassem-

bling tool of long liner of
3916009


lower arm

Disassembling tool of
upper arm liner
3916010


 SST Special Tool
Special Service Tool B-3

SST Special tool

Application position
Diagram Tool Name tool number Front axle Rear axle Remark
2WD 4WD

Press fitting tool of up-

per arm liner 3916011

Disassembling and as-

sembling tools of wheel
3916012

brake cylinder of front
brake caliper

Disassembling tool of
front drive shaft bearing 3916013

Pneumatic caliper of
outer sleeve of front drive 3916014

shaft

Press fitting casing of

front drive shaft bearing 3916015

Disassembling tool of
3916016


main teeth oil seal

Press fitting tool of main

teeth oil seal 3916017

Disassembling tool of
long semi-axis 3916018

Electric cutch tester

3916019

Oil seal of long semi-

Disassembling tool of oil axis of front axle
3916020

Inner oil seal of rear axle
seal and needle bearing shaft
Needle bearing of long
semi-axis
B-4 SST Special Tool
Special Service Tool

SSTSpecial Service tool

Application position
Diagram Tool name tool number Front axle Rear axle Remark
2WD 4WD

Press fitting tool of oil

3916021

seal of long semi-axis

Disassembling bracket of
3916022

long semi-axis bearing

Disassembling tool of
inner race of small bear- 3916023

ing of main teeth

Disassembling bracket of
inner race of large bear- 3916024


ing of main teeth

Press fitting casing of

inner race of large bear- 3916025


ing of main teeth

Press fitting casing of

outer race of large bear- 3916026


ing of main teeth

Press fitting casing of

outer race of small bear- 3916027


ing of main teeth

Disassembling tool of
3916028


differential side bearing

Press fitting tool of dif-

3916029

ferential side bearing

Mounting tool of needle

3916030

bearing of long semi-axis
 SST Special Tool
Special Service Tool B-5

SSTSpecial Service tool

Application position
Diagram Tool name tool number Front axle Rear axle Remark
2WD 4WD

Press fitting tool of long

3916031

semi-axis bearing

Electric cutch tester 3916032

Disassembling tool of
3916033

half-shaft bearing

Press fitting casing of

3916034

half-shaft bearing and oil
seal

Mounting tool of rear

3916035

axle oil seal

Mounting tool of main

3916036

teeth oil seal

Change oil seal of rear

3916037

axle main teeth on
vehicle

Mounting tool of main Change oil seal of

3916038
rear axle main teeth
teeth oil seal
on vehicle

Mounting tool of main

3916039
Use with torsion
teeth oil seal
spanner together

Spanners of adjusting
3916040

ring of side bearing of
differential