Qingdao Jinlihua Textile Machinery Co.,Ltd (Qingdao Jinlihua medical supplies co.

,Ltd)
Address: No.557,Weihe Road,Huangdao Zone,Qingdao,Shandong province,China. PC 266555

医用纱布织造漂白产线

一、 工艺流程：

1、纱线整经---2、整好经的经纱进行穿综----3、喷气织机织造---4、卷扬机对纱布胚布
进行漂白纱筒成卷----5、翻转机发转----6、漂锅进行漂白---7、漂白后的纱布进行脱水处理
---8、烘干机烘干成卷。
1. Yarn warping --- 2, warp yarn for threading---- 3, air-jet loom weaving --- 4, winch
bleaching gauze embryo cloth into rolls---- 5, flipping machine hair ---- 6, bleaching pot for
bleaching --- 7, bleaching gauze after bleaching treatment--- 8, dryer drying into rolls.

流程图示
 Qingdao Jinlihua Textile Machinery Co.,Ltd (Qingdao Jinlihua medical supplies co.,Ltd)
Address: No.557,Weihe Road,Huangdao Zone,Qingdao,Shandong province,China. PC 266555

第一步:纱线整经：
JLH-Z-230 型一次性整经机

JLH-Z-230disposable warping machine technology and related standards

一、整经机技术性能标准 Technical performance standard of warping machine
1．品种适用范围：6S-42S 纯棉纱 Variety scope of application: 6s-42s Pure cotton yarn
2．整经幅宽：2300mm，压辊长度 1860mm;（可调）Warping width: 2300mm, pressing roller length: 1860mm;
(adjustable)
3．织轴规格：盘片直径 800mm; Specification of weaving shaft: disc diameter 800mm;
4．整经速度：≤150m/min; Warping speed: ≤ 150m / min;
5．断头制动距离：≤3.5m; Broken end braking distance: ≤ 3.5m;
6．压纱原理：悬臂式加压、压力均衡、可调，无大小头； Yarn pressing principle: cantilever pressurization,
balanced pressure, adjustable, no big and small ends;
7．计长方式：织轴、导纱辊同步计长； Length counting mode: synchronous length counting of weaving shaft
and yarn guide roller;
8．整经断头率：≤0.3 根/百根.万米; End breakage rate of warping: ≤ 0.3 pieces / 100 pieces 10000 meters;
9．筘齿：39 齿/片；Reed teeth: 39 teeth / piece;
10．经轴跳动度：使用标准经轴检验≤0.3mm;Warp Beam runout: check with standard warp axis ≤ 0.3mm;
11 ． 对 应 织 布 机 型 号 ： JLH9100-230; 用 于 织 轴 传 动 的 葵 花 齿 设 计 方 案 ； Corresponding Loom Model:
jlh9100-230; Design scheme of sunflower teeth for weaving shaft transmission;
二、结构 Structure
1．采用钢板焊接整体框架结构，无抖动，稳定性能高；Steel plate welded integral frame structure is adopted,
which has no shaking and high stability;
2．人机操作界面位于车头的右侧，用于设定工艺参数及观察反运行数据，并有故障诊断显示；The
man-machine operation interface is located on the right side of the front of the car, which is used to set
process parameters and observe the reverse operation data, and has fault diagnosis display;
 Qingdao Jinlihua Textile Machinery Co.,Ltd (Qingdao Jinlihua medical supplies co.,Ltd)
Address: No.557,Weihe Road,Huangdao Zone,Qingdao,Shandong province,China. PC 266555

3．采用 22KW 三相交流电动机直接驱动织轴，变频调速，恒张力卷绕；Using 22KW three-phase AC motor

to directly drive the weaving shaft, frequency conversion speed regulation, constant tension winding;
4．逻辑动作由 PLC 控制，设有联锁保护功能；The logic action is controlled by PLC, with interlock protection
function;
5．刚性安全防护装置，由接近开关控制起动、点动按钮操作，安全可靠；The rigid safety protection device
is controlled by the proximity switch to start and operate the jog button, which is safe and reliable;
6 .W 型伸缩筘，由摆动马达实现筘左右往复摆动，筘左右对中由电机驱动；W-type telescopic reed, the reed
swings reciprocally from side to side by the swing motor, and the left and right centering of the reed is driven
by the motor;
7．设有筘吹风装置，保持筘的清洁；Equipped with a reed blower to keep the reed clean;
8．织轴直接计长，通过光电编码器检测，PLC 控制，织轴度长误差＜0.05%；The length of the weaving shaft
is directly measured, detected by the photoelectric encoder and controlled by PLC, and the length and
length error of the weaving shaft is less than 0.05%;
9．气液转换装置驱动钳式制动器，制动灵敏、可靠，加压辊及测长辊由电气控制保证同步制动；The gas-liquid
conversion device drives the caliper brake, which is sensitive and reliable in braking, and the pressure roller
and the length measuring roller are controlled by electric to ensure synchronous braking;
10．采用日本安川变频器，调正范围大，确保恒线速卷绕；Adopt Japan Yaskawa inverter, wide adjustment
range to ensure constant line speed winding;
11．导纱辊制动采用电磁制动器，编码器计长；The yarn guide roller adopts electromagnetic brake, and the
encoder measures the length;
12．采用坚固的织轴支承结构及安全保险装置，突然断电，断气时保证织轴不会脱落；Adopt sturdy weaving
shaft support structure and safety device to ensure that the weaving shaft will not fall off when the power is
suddenly cut off;
13．织轴拍合采用锥齿轮接合，定心准确，夹紧放松非常灵活，并配有锁紧功能；The weaving shaft is engaged
by bevel gears, the centering is accurate, the clamping and loosening are very flexible, and it is equipped
with a locking function;
三、筒子架 Creel
1．锭距：270×270mm Spindle distance: 270×270mm
2．筒子架层数：8 层 Number of creel layers: 8 layers
3．筒子架头份：2592 根 Creel head portion: 2592 pieces
4．筒子架型式：固定式四路出纱筒子架（张力器架可左右打开）； Type of creel: fixed four-way yarn-out creel
(the tensioner frame can be opened left and right);
5．张力器架打开幅度：1000mm; Tensioner frame opening range: 1000mm;
6．筒子架结构采用钢管支承结构，美观大方，坚实耐用，运行无抖动，矩形排列型式，配二立柱铁架张力
器，挡纱板φ90，调节张力器支板角度可获得理想张力，红外线断经自停装置具有断头显示功能；配备吹风
扇，保持筒子架的清洁；The structure of the creel adopts the steel pipe support structure, which is beautiful
and elegant, solid and durable, and has no jitter in operation. The stop device has a broken end display
function; it is equipped with a blowing fan to keep the creel clean;
四、整经机控制标准 Warping Machine Control Standard
1．.整机控制采用德国西门子公司生产的 PLC 自动控制单元实现，并配备了人机操作界面；The control of the
whole machine is realized by PLC automatic control unit produced by Siemens, and equipped with
man-machine interface;
2．主要配套件见配置清单；See the configuration list for the main accessories;
3．供电、压缩空气方面的要求（由买方负责提供）Requirements for power supply and compressed air
(provided by the buyer)
3.1 供电电源：380V/50HZ，最大电压误差±5% Power supply: 380V/50HZ, maximum voltage error ±5%
3.2 压缩空气气源：输出压力 0.6mpa,无油、无水、无灰尘；并送至设备接口；Compressed air source: output
 Qingdao Jinlihua Textile Machinery Co.,Ltd (Qingdao Jinlihua medical supplies co.,Ltd)
Address: No.557,Weihe Road,Huangdao Zone,Qingdao,Shandong province,China. PC 266555

pressure 0.6mpa, no oil, no water, no dust; and sent to the equipment interface;
3.3 负责将合格的电源送至车头控制箱；Responsible for sending qualified power to the front control box;
五、机器外形尺寸：31000mm×7600mm×2600mm Machine dimensions: 31000mm×7600mm×2600mm
六、其它技术参数：Other technical parameters
1．输入电源：3×380V±10%；Input power: 3×380V±10%;
2．输入频率：50HZ±5%；Input frequency: 50HZ±5%;
3．装机容量：22KVA(标准型) Installed capacity: 22KVA (standard type)
4．0.3L0.6MPa;
5．整机空机运行噪音不大于 80dB; The running noise of the whole machine is not more than 80dB;
七、主要配置明细
序号 型号 名字 数量 制造商

1 6ES7-214-1BDF23-0 CPU 1 西门子 Siemens

XA0
2 222-1HF22-0XA0 模块 module 1 西门子 Siemens

3 A1000 变频器 Inverter 1 日本安川 Yasu River,

Japan
4 506MV 触 摸 屏 touch 1 威伦 Willen
screen
5 CJX2-4011 接触器 contactor 2 施耐德 Schneider

6 CJX2-0901 接触器 contactor 3 施耐德 Schneider

7 S-145-24 电源 power supply 1 台湾明维 Taiwan

Mingwei
8 HH52P 继电器 relay 5 施耐德 Schneider

9 E2E-X10ME1 进接开关 Access 3 RK

switch
10 NF63A 空气开关 air 1 施耐德 Schneider
switch
11 C65N3P 断路器 breaker 1 施耐德 Schneider

12 C65N2P 断路器 breaker 3 施耐德 Schneider

13 RT18-32 保险丝 fuse 3 施耐德 Schneider

14 ZB2-BZ102C 按钮 button 3 施耐德 Schneider

15 TRD-J360-RZ 编码器 Encoder 2 光洋 Koyo

16 轴承 bearing TWB

17 气动原件 Pneumatic 亚德客 AirTAC

components

（1） 分两种,425 和 740 用

（2） 注意客户需要织机的门幅一边配备相应的整经机（织布门幅、品种多不多？一般标
 Qingdao Jinlihua Textile Machinery Co.,Ltd (Qingdao Jinlihua medical supplies co.,Ltd)
Address: No.557,Weihe Road,Huangdao Zone,Qingdao,Shandong province,China. PC 266555

配 k 可调门幅，客户确认整经门幅可定制整经机，价格可相应优惠）

第二步：织造

1、 织前准备，穿综

JLH-CK Wear reed shaft

TECHNICAL DATA

一、the machine function:

The machine will reed the cotton yarn from warp beam to droppers, ready for use in weaving

machine

二、the main technical data of the machine:

1, Warranty 12 months

2, Place of origin : China

3, Date of manufacturing: New made, depend on invoice date

4, Installation : no need to installation

5, Spare part: No
 Qingdao Jinlihua Textile Machinery Co.,Ltd (Qingdao Jinlihua medical supplies co.,Ltd)
Address: No.557,Weihe Road,Huangdao Zone,Qingdao,Shandong province,China. PC 266555

2、喷气织机织造：

JLH425-230/280 High Speed medical gauze air jet loom

Advantage:The advanced loom to make medical gauze,good quality fabric,high output.
Weaving scope:all gauze fabric
Respective fabric:Raw material 40s x40s density per inch 26x18 30x20
Machine width 210cm,two pcs fabric in one loom,production/24hour 1600-2000m
Technical parameter
Item Specification Remark

Reed width Reed width(cm) 幅宽 190 210 230 280 340 360
幅宽 Useful reed width Reduce 0-60cm (150-230cm)
有效幅宽 减少 0-60cm(110-170cm)
Reduce 0-80cm (280cm above)
减少 0-80cm(110-170cm)
Fabric 织物 Material & weave Gauze fabric 纱布面料
材料和编织 Low density baby product
低密度婴儿用品
1.8kw(190cm-230cm)
Power 动力 Main power 主电机 2.5kw 280cm
2.8kw 340cm
 Qingdao Jinlihua Textile Machinery Co.,Ltd (Qingdao Jinlihua medical supplies co.,Ltd)
Address: No.557,Weihe Road,Huangdao Zone,Qingdao,Shandong province,China. PC 266555

RPM 550 600 650 (below 230 cm ）

RPM 550 500 （280cm)
Speed Motor-belt pulley RPM 400 450
速度 电机皮带轮 (340,360cm)
Weft selection Single color 单喷 Double color 双喷
选纬 Four color 四喷 Six color 四喷
Magnetic valve SMC Japan 3 nozzle per valve
Weft 电磁阀 SMC 日本 每个阀门 3 个喷嘴
insertion Feeder 储纬器 1 2 (above 230cm，must be 2 feeder)
引纬 超过 230cm 必须两个储纬器
Nozzle 喷嘴 Energy-saving nozzle 节能喷嘴
Shedding method Crank plain shedding 平机开口
Shedding 开口方式
开口 Heald frame 综框 2 4 Brand Jinlihua China
品牌中国金利华
Mechanical type Single beam
Let off 机械送经 单经轴
device Electronic type
送经方式 电子送经
Flange diameter Ø800 Ø914 Ø1000
边盘直径
Take up 卷曲 Electronic take up (ETU)电子卷曲
Take up Mechanical take-up(MTU)机械送经
device Max cloth roll Ø600mm(crank）机内卷
卷曲方式 diameter Ø1200mm(jumb batching motion）机外卷
最大卷布直径
Weft density 纬密 Take 40s cotton yarn for example
以 40S 举例
4-60picks/inch 4-60 根/英寸
Four-bar beating-up motion （ below
Beating Roller beating system 280cm)
打纬 4 连杆打纬（低于 280cm）
Six-bar-beating-up
Selvage 布 Leno gear selvage 纱罗齿轮布边
边
Edge 边 Tuck-in device or leno selvage
折入或者毛边
Cutter 剪 Mechanical cutter 机械剪刀
刀
Lubrication Manual oil supply 手动供油
Automatic oil supply 自动供油
Weft stop Reflective weft feeler 反光纬触
Stop 纬停 One heads system 单探头系统
motion Two head system 双探头系统
停车装置 Warp stop 经停 Electric 2-row contact bar system
电动双排接触杆系统
Control Baina brand With NAVI-borad(data setting, automatic
system Made-in-China control,monitoring,self-diagnosis
 Qingdao Jinlihua Textile Machinery Co.,Ltd (Qingdao Jinlihua medical supplies co.,Ltd)
Address: No.557,Weihe Road,Huangdao Zone,Qingdao,Shandong province,China. PC 266555

function, WPS interface)

带 NAVI-borad（数据设置、自动控制、
监控、自诊断功能、WPS 接口）

3、织造辅助设备及工具
（1）空压机、冷干机、储气罐、三级过滤
SVC-XXA/W（低压双级节能）

TECHNICAL DATA

一、the machine function:

In the textile industry, air compressors are widely used. The power source of the air-jet loom is the compressed air
as the carrier for weft insertion. So a good air compressor directly affects the efficiency of the entire textile
process.

螺杆式空压机产品参数表 SVC-110A-Ⅱ
Product Specification of Screw Type Air Compressor（SVC-110A-Ⅱ）

机型 Machine Model SVC-11A-Ⅱ

排气量 AIR Delivery（m³/min） 0.45 Mpa 7.5～30.0

冷却方式 Cooling Type 风冷 wind cooling

空气出口温度 Outlet Temperature (℃) 环境温度+15℃mbient temperature+15℃

空气出口管径 Outlet Pipe Diameter (inch) DN100

传动方式 Transmission method 直联（ Driven）

润滑油量 Lubricant Requirement (L) 150

 Qingdao Jinlihua Textile Machinery Co.,Ltd (Qingdao Jinlihua medical supplies co.,Ltd)
Address: No.557,Weihe Road,Huangdao Zone,Qingdao,Shandong province,China. PC 266555

排气量控制方式 Ventilation method 25%-100% 自动控制，恒压输出

压 缩 机
气体含油量 oil content (ppm) ≤3
Compressor
振动 Concuss (mm/s) ≤7

最高工作环境温度
52℃
Max Working Ambient Temperature (℃)
电 动 机 功率 Power (kW) 110
Electric Motor
起动方 Starting method 变频启动 Frequency conversion starting

防护等级 Protection Level IP55

冷却方式 Cooling Type 风冷 wind cooling

控制方式 Control method 变 频 恒 温 控 制 Variable frequency constant

冷 却 系 统
temperature control
cooler
排风风扇功率 Fan Power（KW） 4.5

整 机 输 入 电 压 / 频 率 Input voltage / frequency of the whole

380/50
machine（V/Hz）
安全保护装置 Safety Indicating Device 有 Yes
保养指示 Maintenance tips 有 Yes

微电脑控制 Microcomputer control 智能控制 Intelligent control

噪音 Noise（db） ≤90dB

净重 Weight (kg) 3800

外 形 尺 寸 长 Length (mm) 2750

External
宽 Width (mm) 1850
Dimension
高 Height (mm) 1900

空压机配置清单 Air compressor configuration list

序号 名称 产地或品牌 备注
1 螺杆主机 SEIZE 萨震压力定制双级压缩高效主机
2 空滤 SEIZE-Donaldson 定制大面积低压降滤芯
3 进气阀 VMC/红星 兼备电磁阀、降噪音、防吐油
4 冷却器 冠云/爱赫德 定制高效且表面抗氧化图层处理
5 油气桶 威尔泰克/亚克/富海华 专利设计，立式/旋风分离
6 油分芯 SEIZE 定制低压差高效油分芯
7 油滤座 红星 铸铝
8 油滤 SEIZE-Donaldson 定制高精度滤芯
9 螺杆油 SEIZE 萨震定制专用油
 Qingdao Jinlihua Textile Machinery Co.,Ltd (Qingdao Jinlihua medical supplies co.,Ltd)
Address: No.557,Weihe Road,Huangdao Zone,Qingdao,Shandong province,China. PC 266555

10 安全阀 燕峰 铜质
11 最小压力阀 红星 具止回和压力维持功能
12 温控阀 红星/克俐托 萨震定制
13 前置滤网 SEIZE 金属边框，高效预过滤
14 管路总成 SEIZE 不锈钢精拔钢管或磷化管
15 联轴器 ROTEX 美国
16 中心托架 SEIZE 钢制高精度和高强度托架
17 罩壳总成 SEIZE 冷轧板/粉体涂装/防紫外线
18 液晶显示屏 SEIZE -INVT 定制高灵敏度显示屏
19 主机变频器 SEIZE -INVT 定制高端变频系统
20 风机变频器 SEIZE -INVT 定制高端变频系统
21 电控盘 萨震-施耐德 定制高端电控系统
22 永磁电机 SEIZE-HANCI/驰美/中达 定制耐高温，高效永磁电机
23 风机电机 WEG 知名品牌高效耐高温电机
24 风机 洛森 德国
25 温度传感器 欧利德 萨震定制
26 压力传感器 丹佛斯 萨震定制
27 电磁阀 ODE 意大利
28 热继电器 施耐德 法国
29 回油单向阀 红星 具有限流止回功能
30 波纹管 乐鼎/精密 耐腐蚀,耐高温,使用寿命长

风冷型冷冻式干燥器技术参数 Air-cooled freezing dryer technical parameter

一、风冷型冷冻式压缩空气干燥器 Air-cooled freezing dryer

设备型号 Equipment type CD-850F

数量 quantity 1台

名称 name 技术性能及参数 technical parameter 备注

 操作条件 Operating conditions

处理介质 Treatment medium 压缩空气 compressed air
处理气量 Treatment gas volume 85m3/min

工作压力 working pressure 0.6-1.0Mpa (G)

进气温度 inlet temperature 5-60 ℃

环境温度 ambient temperature 2~40℃

 性能指标值 Performance index value

压力露点 Pressure dew point 2-10℃

 Qingdao Jinlihua Textile Machinery Co.,Ltd (Qingdao Jinlihua medical supplies co.,Ltd)
Address: No.557,Weihe Road,Huangdao Zone,Qingdao,Shandong province,China. PC 266555

噪声控制 noise control 75db

工作状态 functional mode

运行周期 cycle of operation 24 小时连续运行 Run continuously for 24 hours

 电力需求 power demand

电源条件 Power supply condition 380V/50HZ

风机功率 Fan power 1.8KW

耗电量 power consumption 15.42KW

 管路连接尺寸 Pipe connection size

压缩空气进口尺寸 Import size 法兰 DN150

干燥空气出口尺寸 outlet size 法兰 DN150

 外形尺寸及重量

外 形 尺 寸 ( 长 * 宽 * 高 )External 2300mm*1700mm*1970mm
供参考
Dimension(L*W*H)
设备总重量 Weight (kg) 约 1050kg 供参考

储气罐规格 Air Tank：

规格型号 Equipment type 5m³8kg

设计压力/工作压力 working pressure MPa 0.84/0.8

全容积 Full volume MP 5.0

出气口 air vent/进气口 admitting port DN100/DN100

净重 Weight (kg) 754

外形尺寸 罐长 Length (mm) 2700

External
Dimension 宽 Width (mm) 1400

高 Height (mm) 3700

过滤器 Line Filte：

ITE 单 位
项目名称 name 过滤器 Line Filte
M unit

1 型号 model —— CD-085-C CD-085-T CD-085-A

处 理 介 质 Treatment 压 缩 空 气 压 缩 空 气 压缩空气 compressed

2 ——
medium compressed air compressed air air
 Qingdao Jinlihua Textile Machinery Co.,Ltd (Qingdao Jinlihua medical supplies co.,Ltd)
Address: No.557,Weihe Road,Huangdao Zone,Qingdao,Shandong province,China. PC 266555

滤 壳 材 质 Filter shell
3 —— 碳钢 carbon steel 碳钢 carbon steel 碳钢 carbon steel
material
不 锈 钢 冲 孔 板 不锈钢冲孔板 不 锈 钢 冲 孔 板
4 滤芯骨架 Filter core —— Stainless steel Stainless steel Stainless steel
punching plate punching plate punching plate
额 定 处 理 量 Rated
5 m³/min 85m³/min 85m³/min 85m³/min
throughput

额 定 工 作 压 力 nominal 1.0MPa 使 用 温 度 1.0MPa 使 用 温 1.0MPa 使 用 温 度

6 MPa
working pressure ≤65℃ 度≤65℃ ≤65℃

滤 除 效 率 Filtering
8 % ≥99.9% ≥99.99% ≥99.99%
efficiency

9 过滤精度 Filtering accuracy μm 3um 1um 0.01um

滤 芯 形 式 Filter element 可 更 换 式 可 更 换 式 可更换式 Replaceable

10 ——
form Replaceable type Replaceable type type
聚酯纤维 polyester
11 滤材材质 Filter material —— ATS ATS
fiber

滤 芯 寿 命 Life of filter 正常工况下不小于 正常工况下不小 正常工况下不小于

14 ——
element 8000 小时 于 8000 小时 8000 小时
排 污 方 式 Pollution 手 动 排 污 Manual 手动排污 Manual 手 动 排 污 Manual
15 ——
discharge mode sewage discharge sewage discharge sewage discharge
进气出气接口 Air inlet and
16 DN125 DN125 DN125
outlet interface

（3）自动结经机
BQ198 Automatic warp tying machine

Model: TECHNICAL DATA

 Qingdao Jinlihua Textile Machinery Co.,Ltd (Qingdao Jinlihua medical supplies co.,Ltd)
Address: No.557,Weihe Road,Huangdao Zone,Qingdao,Shandong province,China. PC 266555

一、the machine function:

The warp tying machine is an indispensable automatic equipment in the weaving workshop of the weaving factory.
It is used to connect the warp yarn of the loom with the warp yarn of the new weaving shaft to complete the
purpose of warp tying and shaft changing. It can greatly reduce the labor of the weaving factory, reduce the labor
intensity and reduce the cost.
Model: BQ198
工作幅度：1M—4M等不同规格
Working range: 1M to 4Mand other different specifications
机器型号：波球牌198型自动结经机
Machine model: BOQIU 198 automatic warping machine
选纱方式：有绞无绞自动选纱
Yarn selection mode: twist-free automatic yarn selection
打结方式：管式打结（长结）
Knotting method: tubular knotting (long knot)
结经原料：适用于棉纱，毛纱，真丝，混纺纱等
Warp knitting raw materials: suitable for cotton yarn, wool yarn ,real silk , Blend yarn, etc.
结经范围：2S—200S,20D—3000D
Warp knotting range: 2S-200S、20D-3000D
结经速度：60个结/分钟—600个结/分钟
Velocity of menstruation: 60 knots per minute - 600 knots per minute
电源：电压36V
Power supply: voltage 36V
电流：5A
Current: 5A
电机功率：100W
Motor power: 100w
二、the main technical data of the machine:

1, Warranty 12 months

2, Place of origin : China

3, Date of manufacturing: New made, depend on invoice date

4, Installation : no need to installation

5, Spare part: No

（4）上轴车
JLH-230/280（随织机筘幅） Hydraulic Palm Frame Upper Shaft Vehicle
 Qingdao Jinlihua Textile Machinery Co.,Ltd (Qingdao Jinlihua medical supplies co.,Ltd)
Address: No.557,Weihe Road,Huangdao Zone,Qingdao,Shandong province,China. PC 266555

TECHNICAL DATA

一、the machine function:

The machine can put the yarn on the weaving beam into the gauze weaving machine, and then make the gauze
weaving machine rotate smoothly to weave the gauze. In some large textile factories, a good Hydraulic Palm
Frame Upper Shaft Vehicle can also directly improve the efficiency of their work, and can also ensure the safety of

workers and reduce the possibility of accidents.

二、the main technical data of the machine:

1, Warranty 12 months

2, Place of origin : China

3, Date of manufacturing: New made, depend on invoice date

4, Installation : no need to installation

5, Spare part: No

（5）运轴车
JLH-230/280（随织机筘幅） Fork table carrier

TECHNICAL DATA

一、the machine function:

The machine use for transport the warp beam, it suitable 2300mm warp beam transportation.

二、the main technical data of the machine:

1, Warranty 12 months
 Qingdao Jinlihua Textile Machinery Co.,Ltd (Qingdao Jinlihua medical supplies co.,Ltd)
Address: No.557,Weihe Road,Huangdao Zone,Qingdao,Shandong province,China. PC 266555

2, Place of origin : China

3, Date of manufacturing: New made, depend on invoice date

4, Installation : no need to installation

5, Spare part: No

（6）落布车 Drop cart

大卷装用！ 机内卷用