MB star C3 and SD Connect compact 4 for
Benz software activation and error solution
1) How to use platinum software to reset SBC
2) How to activate platinum software
3) How to activate ordinary star hdd
Part 1: How to use platinum software to reset SBC
when you choose SBC system, it will have an option, SBC RESET, after you enter this
option, you will see special function, enter this and it will ask for the password, for this
password, just fill anything you like, then click next step, then click ok, then follow the
prompt to do next.
Here is the second method:
SBC TOOLS RESET
It started like most of them.......
As a request !!
So,it was a combination , of a faulty SBC ,common sence , LOTS of time and GUTS to
figure this out
Make sure engine is running !!!
In Developer mode you need to go to Developing data -> drives -> Total list of all activations
to see how many times brake has been pressed there is a line that says: Brakes payers
(DJ_GetBrLive) or DJ_GetBrLiveTime
then 1 line down there you see Update brakes payer and life counter F recalculate -> click it!
Parameter uINBR = 0
then click F3
1 line down Brakes payers set to any value (DJ Set Br) -> click it
Parameter uINBR = 0
then click F3
then scroll down untill you see the line's :
Life counter F recalculate (DJ_CalcLiveTime)
Parameter uINBR = 0
then click F3
Life counter F Recalculate and write (DJ_BuildAndWriteF)
Parameter uINBR = 0
then click F3
Log out of SBC !!
log out of verhicle !!
let engine run at least 10 minutes or drive at least 10 minutes
If no coils are damaged , SBC fault code is not AKTUEL nomore
Note:
(Dj_setNBr) Here you SET new brake counter value back to 0
(Dj_setNBr) uINBR = 0
Resetting break counter to zero is in my opinion , not messing with .....
each time SBC powers up it checks itself time after time
If there occures any problem in SBC unit with valve,brushes or whatever , it will go into error
anyway. that you will NOT be able to erase in Dev mode
If you switch on contact of Brand new MB with SBC and press break 300.000 times it will go
into this so called "error" you wanna say SBC is broken then ? without driving a milimeter ?
No it's indication to have SBC unit checked by MB workshop $$
Yes it's true that MB has to replace Faulty SBC units for free
since Factory will pay all there labor & material
But most Dealers try to have costumer pay for this procedure claiming costumers car has no a
Dealer serviced History
Part 2: How to activate the software for Star series. Here is the detailed instruction for
Platinum version activation and other ordinary star HDD activation:
For this SS160 Platinum version star software. It has the keygen on the desktop. You can
activate the software by yourself. If you do not know how to do, you can send the activation
code to us for activation.
Xentry: When you open software, you will see software like this, click this icon:
you will see data like this. Use this HARDWARE ID and APP ID for xentry activation.
After you get the code, click start keys, and you will see this, input the activation data to the
blank
For EPC and WIS activation:
Click this on desktop. Then you need to fill in user id and password. EWA NET user: admin,
password: supermbstar
Part 3: For other star HDD you need to provide the following information to use for
activation:
1) Software version: Like 2015.3, 2015.5 and so on.
2) Activation data:
HardwareID: 105A-026B-F651-4AAE-BE32-D9A8-07C4-2A72 OR Hardware fingerprint:
E1BC-2353 (Hardware ID is for new star software, hardware fingerprint is for old star
software)
HW ID: 1A2027341ERB
APP ID: 250
(LAN-ID): 0022694C272A
Where to find these data:
1) For HardwareID: used for DAS activation
We will give you the license, just run it, then DAS activated ready.
For Hardware fingerprint: (Used for DAS activation)
3) For LAN ID: Used for EPC WIS activation
4) HW ID and APP ID: Used for Xentry activation
