HANDHELD LASER DISTANCE METER USER MANUAL EnglishIntroduction Firstly thank you for your choice on our handheld laser distance meter. Please carefully read the safety instructions and the user manual before using this product, otherwise it may result in hazardous laser radiation and electric shock. The person responsible for the equipment must ensure that all users understand these directions and adhere to them. Safety Instructions 4.This product is a class II laser product. Please DO NOT stare into beam at any time when operating this product! 2.Please DO NOT looking directly into the beam with optical aids (e.g. binoculars, telescopes)! 3.Please DO NOT remove any safety labels on this product! Caution: 4.Please avoid kids to use the meter. 2.Do not open the meter without allow from professional person. 3.Please keep the manual, it is useful when you use it. Unpacking inspection 1,Mainframe one unit 2,User manual one piece 3,AAA battery(2*1.5V) two pieces 4,holding rope one pieceBasic Functions Single Measurement Max. / Min. Measurement Continuous Measurement Area / Volume / Pythagoras Plus and Minus Meter/Ft/In Switch Measuring Reference Buzzer Indicator Historical Data Records Data Clean up Error Message Code Battery Indicator Digital Level(angle measuring) Laser Auto. Switch off Instrument Auto. Switch off 180s Telemeasuring height directly, even though there are some barriers in front of target. = Be. 8Technical Parameters: F Measuring Range 0.05m~40m 4 0.05m~60m 0.05m~80m 2 0.05m~100m 3 0.05m~120m 4 0.05m~150m S Measuring Accuracy £1.5mm 5 Measuring Unit ™,ft,in zg Laser type 620~690nm Laser Class I class,<1mw LC Single Measurement Time 0.25s Operating Temperature 0~+40C Storage Temperature -20~+65C Batteries AAA(Alkaline), 2x1.5V Measurements Per Battery Set >8000 Weight (Without Batteries) Approximately 82g Dimensions (LxWxH) 115 x 50 X 23mm Comment: * The deviation occurs under unfavorable conditions such as bright sunlight or when measuring too poorly reflecting or very rough surfaces, the environment temperature is too high or too low. ™ When measuring distance within 10m, measurement pos _1s £1.5mm; more than 10m, measurement accuracy is eas ollows: +1.5mm + 0.05* (D-10) (D: Measuring Distance.Forbidden 4, Opening the equipment by using without allow. . Measuring to sun Others measuring out of appointed range. immersing the equipment in water. Cleaning the lens using alcohol or any other organic solvent. . Wiping the lens directly with fingers or other rough surfaces. . Powering the equipment beyond the rated DC voltage. tools (screwdrivers, etc.) NOObhwoN LCD Indicator Laser indication and reference Continue measuring Area volume measuring Pythagoras measuring Error indication rorya | Hi: (eee a ahahaha) a nO cr" Power indication Max and min indication Date storage Unit indication Angle indication Current measurement Caculation displayKeyboard Indicator Switch on/Measuring Measuring Reference Historical Data/ Unit Switch Clean up/Switch off FOeEle Function Switch Plus/forward Minus/Backward qStart-up 1 Battery Installation con Corps iid. ccording to figures, remove battery iment = > aa paneries with correct polarity according to battery indications c. Close the battery compartment lid figure A *Caution: 1. Please do not mix new and old batteries, Use alkaline batteries or rechargeable batteries only. 2. Please replace batteries when the symbol flashes permanently in the display 3. Please remove the batteries before any long period of non-use 4. Out of power batteries must not be disposed of with household, care for the environment and take them to the collection points provided in accordance with national or local regulationsOperation Switch on/off Short-time press button to switch on the equipment, indication as shown as figure A. figure A Change Measurement Reference Default measuring reference is the bottom of meter, short-time Press (4 )to change the measuring reference to the top of meter. Short-time press &, laser reflection signal indication will display, meanwhile battery intensity indication display as shown as figure B; figure BLong-time press & to switch off the equipment. The laser will be switched off automatically after 30 seconds a equipment will be powered off after 3 minutes without any ope’ Clear Button Short-time pressing & button to clear the last command o displayed data one by one; Measurement Single-mode Measurement When equipment is switched on, short-time press @ will activate the laser, then aim the laser onto target and press @ again will trigger single-mode measurement, the result is will results displayed immediately as shown in figure D.Continuous-mode Measurement When the equipment is switched on, long-lime pressing @> button will trigger continuous-mode measurement . MIN; MINIMUM VALUE MAX: MAXIMUM VALUE Current measurement value is displayed in LCD bottom line as sh Own in figure E. figureE Functions Area, Volume. Indirect Mea: s isurem ee ine ent (Pythagorean Theorem) wi : figure F hen the €quipment is switched on, Press @ro switch me: ‘@Surement functions one by one. Select corresponding function 4nd begin the measurement 9Measurement Levey aT) Measuring Area Q ch Measuring Volume Telemeasuring height directly(Pythagoras) IN auring height 5 Z| (twice Phthagoras plus) : Nl Telmeauring height directly A twice Phthagoras minus) 1 Plus and Minus Functions When the status is single-mode Measurement. Press + the meter can calculate the last measurement a Current measurent. Press -, the meter can calculate the last measurement minus the current measurent.figure G 2 eon maT R) H SHE nan itty 10Storage 1)Storage m' data records. and Recall of Measurements easurements: press the to review historical 2)Press + or — buttons to scroll through the measurements. Message Code | Possible cause Battery too low Out of range figure | Remedy Change batteries Measure target within the range Received signal too weak Background brightness too high Out of display Use light color target; Hold Quick Measure more stead! Use dark colored target