LOW VOLTAGE

STANDARD EFFICIENCY MOTORS IE1

e-catalog
 Table of Content

General specification
Standards and regulation 5
Conditions of installation 5
Insulation and temperature rise 6
Tolerances 6
Mechanical design 7
Mounting arrangements 8
Lubrication and maintenance of bearings 10
Lubricating nipples 10
Electrical design 11
Three-phase squirrel-cage motors driven by frequency inverters 13
Cast Iron Motors 14
Maximum Permissible axial loads without radial load 15
Anit-condensation heating 17

Technical data
IE1 General Performance 18
Dimensions foot mount B3 22
Dimensions foot flange mount B35 24
Dimensions foot flange mount B5 and V1 26
Dimensions face-flange mount B14A and B14B 28
Top terminal box 29
Side terminal box 30
Bearing & Lubrication 31

Notes
Revisions
All technical data, outputs, dimensions and weights, stated in this catalogue, are subject to change without notice.
Illustrations do not purport to show constructional details.

General specification 4
 General specification

Standards and regulation

The motors comply with the relevant standards and regulations, especially:

Electrical
IEC - Standard EN - Standard Content
IEC 60034 - 1 EN 60034 - 1 Rating and performance
IEC 60034 - 8 EN 60034 - 8 Terminal markings and direction of rotation
IEC 60034 - 12 EN 60034 - 12 Starting performance
IEC 60034 - 30 EN 60034 - 30 Efficiency classes of single - speed, three-phase, cage - induction motors (IE-Code)
IEC 60038 EN 60038 Standard voltages

Mechanical
IEC - Standard EN - Standard Content
IEC 60072 EN 50347 Dimensions and outputs
IEC 60034 - 5 EN 60034 - 5 Degrees of protection
IEC 60034 - 6 EN 60034 - 6 Methods of cooling
IEC 60034 - 7 EN 60034 - 7 Type of construction
IEC 60034 - 9 EN 60034 - 9 Noise limits
IEC 60034 - 14 EN 60034 - 14 Vibrations

Conditions of installation
° C.
Exceptions are indicated on the rating plate.
The motors comply with protection degree IP 55 according IEC 60034-5 (higher protection degrees on request).
Motors with standard design for horizontal mounting arrangements are suitable for indoor and protected outdoor installation,
climate group Moderate (temperature of coolant -20° C to +40° C).
In case of unprotected outdoor installation or aggravating climatic conditions (moisture category wet, climate group
Worldwide, extremely dusty site conditions, aggressive industrial atmosphere, danger of storm rain and coastal climate,
danger of attack by termites, etc.), as well as vertical mounting, special measures are required, such as:
Protective cowl (for vertical mounting with shaft - down)
For vertical mounting with shaft - up flange drainage and additional bearing seal, if necessary
Special painting
Treatment of winding with moisture protection varnish
Anti-codensation heating (anti-condensation heating of winding, if necessary)
Condensation drain holes

The special measures to be applied have to be agreed with us once the conditions of installation have been clarified.

5 General specification
 General specification

Insulation and temperature rise Class ∆T* Tmax

The insulation of the motors complies with temperature class F according EN 60034-1. B 80 K
The table beside defines the temperature rise ( ∆T*) and maximum temperatures at
the hottest points of the winding (Tmax) according to the temperature classes of the F 105 K
EN 60034-1 standard. H 125 K

Tolerances
For industrial motors according to EN 60034-1, certain tolerances must be allowed on guaranteed values, taking into consideration
the tolerances for the manufacture of such motors and the variances of the used materials. The standard specification
sheet includes the following remarks:

Guarantee of all or any of the values according to the table is not obligatory. Guaranteed values that are subject to tolerance
have to be mentioned in offers explicit. The allowed tolerances must be in accordance with the table.
Where a tolerance is stated in only one direction, the value is not limited in the other direction.

Values for Tolerance

Efficiency ( ) -0,15 x (1- ) at PN
(in case of indirect determination) -0,1 x (1- ) at PN
Power factor (cos ) – 1-cos
6
, minimum 0.02, maximum 0.07
Slip (s) ±20 % of the guaranteed slip at P N
(at rated load and at working temperature) ±30 % of the guaranteed slip at P N
Starting current (Is) +20 % of the guaranteed starting current
(in case of the intended starting circuit) no lower limit
Starting torque (Ts) -15 % and +25 % of the guaranteed starting torque
(+25 % may be exceeded by agreement)
Pull-up torque (TP) -15 % of the guaranteed value
Breakdown torque (TB) -10 % of the guaranteed value
(after allowing for this tolerance, TB /TN at least 1,6)
Moment of inertia (I) ± 10 % of the guaranteed value

Mechanical tolerances
Parameter Code Area Tolerance
Accordind to IEC 72-1,the tolerances on mechan-
Frame size H up to 250 0.5 mm
nical dimensions of electric motors given > 250 1 mm
besige are permitted.
Diameter of shaft end D-DA from 11 to 28 mm j6
Note: The holes at the shaft end correspond from 38 to 48 mm k6
with DIN 332 from 55 to 100 mm m6
Hub key width F-FA h9
Flange centring N up to 132 j6
> 132 h8

General specification 6
 General specification

Mechanical design
Protection degrees
Protection degress for electrical machines and designated in accordance with IEC 60034-5 by the letters IP and two characteristic
numerals.

First numeral: Second numeral:

Protection against contact and ingress of foreign bodies Protection against ingress of water

IP Description IP Description
0 No special protection 0 No special protection
1 Protection against solid foreign bodies larger than 50mm 1 Protection against vertically falling water drops (condensation)
(Example: inadvertent contact with the hand) 2 Protection against dropping water when inclined by up to 15
2 Protection against solid foreign bodies larger than 12 mm 3 Protection against spray water up to 60 from vertical
(Example: inadvertent contact with the fingers) 4 Protection against shower water from any direction
5 Protection against water projected by a nozzle and from any
3 Protection against solid foreign bodies larger than 2.5 mm direction

6 Protection against heavy seas or water projected in powerful jets

4 Protection against solid foreign bodies larger than 1mm 7 Protection when submerged between 0,15 and 1 m
8 Protection when continuosly submerged in water at conditions
5 Protection against dust (harmful deposits of dust) agreed between the manufacturer and the user
6 Total protection against dust
(is not described for electrical machines according IEC 34-5)

7 General specification
 General specification

Mounting arrangements
Mounting arrangements for rotating electrical machines are designated according to IEC 60034-7, Code I (in bracketsCode II).
Our motors are available according to the table depending on design and frame size.

Foot mounting Flange mounting Motors without end sheild

IM B3 (IM 1001) IM B5 (IM 3001) IM B9 (IM 9101)
Mounting flange
type A according shield and without
DIN 42 948 at roller bearing
drive end on drive end

IM B6 (IM 1051) * IM V1 (IM 3011) IM V8 (IM 9111)

Mounting flange
type A according shield and without
DIN 42 948 at roller bearing
drive end on drive end
IM B7 (IM 1061) * IM V3 (IM 3031) IM V9 (IM 9131)
Mounting flange
type A according shield and without
DIN 42 948 at roller bearing
drive end on drive end

IM B8 (IM 1071) * IM B35 (IM 2001) Mounting flange IM B15 (IM 1201)
type A according shield and without
DIN 42 948 at roller bearing
drive end on drive end
IM V5 (IM 1011) * IM B14 (IM 3601)
Mounting flange
type C according
DIN 42 948 at
drive end
IM V6 (IM 1031) * IM V18 (IM 3611)
Mounting flange
type C according
DIN 42 948 at
drive end

IM B34 (IM 2101) IM V19 (IM 3631)

Mounting flange Mounting flange
type C according type C according
DIN 42 948 at DIN 42 948 at
drive end drive end

* From frame size 225 on request

8 General specification 98
 General specification

Terminal boxes
The location of the terminal box in standard design is on top (view to drive end); on the right or on the left is also possible.
For motors with mounting arrangements IM B6, IM B7, IM B8, IM V5, IM V6 the location of the terminal box is related to an
IM B3 mounting.
The position of the entry openings can be adapted to the existing connection possibilities for most motors by turning the
terminal box by 90°. Please enquire if special accessories should be used (temperature sensors, anti-condensation heating,
etc.).
For motors in standard design, the screwed stuffing boxes do not belong to our scope of delivery.

Belt drive
The data refer only to the normal shaft end at the drive end of IM B3 motors with one speed.

Calculation of radial shaft load: FR = radial shaft load in N

FR 19120 P k [N] P = power in kW
D1 n
n = speed in min-1
D1 = pulley diameter in m
k = belt tension factor
The belt tension factor depends on the type of belt and is assumed to be approximately:
3…4 for normal flat belt without idle pulley
2…2,5 for normal flat belt with idle pulley
2,2…2,5 for V-belt
Please enquire exact data from the belt manufacturer.

Vibration behaviour
The vibration severity of electric motors is determined in EN 60034-14 Mechanical vibration of certain machines with shaft
heights 56 and higher - Measurement, evaluation and limits of vibration severity.
The rotors of the motors are dynamically balanced with half key fitted according to DIN ISO 8821. Other balancing is available
by agreement only.
Our standard motors observe or fall below vibration category A. Motors with ball bearing can be supplied in vibration category
B at extra cost.

9 General specification
 General specification

Maximum operating speed

Rame size 2- pole 4…8 - pole
Motors in basic design are mechanically suitable for the maximum 63…112 5200 3600
operating speeds given beside.
132…180 4600 3000
200 4500 3000
225 4500 3000
250 3900 3000
280 3600 3000
315 S/M 3600 2600
315 L 3600 2600
355 S 3600 2600
355 M 3600 2600
355 L 3600 2600

Lubrication and maintenance of bearings

The bearings of standard motors up to frame size 132 (EH1) have permanent lubrication. Bearing grease K3N according
DIN 51 825 is used (e.g. KLUER ASONIC GHY72, ESSO UNIREX N3 or similar).
Maintenance-free operating time of motors with permanent lubrication at ambient temperature of 40°C and 50 Hz mains
operation:
2- and 4/2-pole motors 10,000 h
4 and more pole motors 20,000 h, but 4 years at most
From frame size 160 the motors are equipped with lubricator and grease.
First lubrication is made with grease K3N according DIN 51 825 (lithium-based, behaviour in the presence of water
accoring DIN 51 807 part 1: level 0 or 1).
For motors with lubricator, the regreasing interval and required quantity of grease is indicated on the rating plate.
For regreasing please observe the operating instructions.
In case of unfavourable conditions (e.g. high ambient temperature, dusty conditions, corrosive atmosphere, operation by
frequency inverter), regreasing should be carried out more frequently.

Lubricating nipples
Flat type lubricating nipple M10x1 according DIN 3404.

10 General specification 10
 General specification

Electrical design
Rated voltage
For the rated voltage of the motors a voltage tolerance of ±10 % applies. According to IEC 60038 the mains voltages may
have a tolerance of ±10 %.
When the motors are operated at the limits of the voltage tolerance, the permissible overtemperature of the stator winding
may be exceeded by 10 K.

Rated frequency
Motors with windings for 50 Hz can be also operated on 60 Hz mains, when the mains voltage increases proportionally to
the frequency.The relative values for starting and breakaway torque remain nearly unchanged and slightly increase for the
starting current.The rated speed increases by the factor 1,2 and the rated power by factor 1,15. Should a motor designed
for 50 Hz be operated at 60 Hz without the voltage being increased, the rated power of the motor cannot be increased. Under
these operating conditions, the rated speed increases by factor 1,2. The relative values for starting and breakaway
torque are reduced by factor 0,82 and the starting current by factor 0,9.

Rated current
The rated currents listed in the selection tables apply to an operating voltage of 400 V. The conversion to other operating
voltages, with power and frequency remaining unchanged, is to be made as follows:

Rated voltage (V) 230 380 400 440 500 660 690
Conversion factor X IN 1,74 1,05 1,0 0,91 0,80 0,61 0,58

Rated torque
Shaft power in kW
Rated torque in Nm 9550
Rated speed in rpm
Power
The power stated in the table applies for constant load at continuous operation according duty class S1 of EN 60034-1,
based on a coolant temperature of 40°C and installation at altitudes up to 1000 m above sea level.
For severe operating conditions, e.g. high switching rate, long run-up time or electric braking, a thermal reserve is necessary,
which may require a higher temperature class or the use of a motor with higher rating. In these cases we recommend
further enquiring and specification of the operating conditions.

Overload capability

with 1,5 times of the rated current at rated voltage. This overload capability complies with EN 60034-1 and will not result in excessive
temperature rise.
When temperature class F is utilized, motors can be operated continuously with an overload of 12 %. This does not apply to
motors which are already utilized according to thermal class F in their standard design.

11 General specification
 General specification

Connection diagrams
Star connection
U1 Star connection is obtained by connecting terminals W2, U2, V2 to each other
and terminals U1, V1, W1 to the mains.
W2 U2 V2
Phase current and phase voltage are: Iph = IN; Vph = VN / 3
IN is the rated current and VN the rated voltage at star connection.
W1 V1
L1 L2 L3

Delta connection
U1 Delta connection is obtained by connecting the end of a phase to the beginning
W2 U2 V2 of the next phase.
Phase current and phase voltage are: Iph = IN / 3 ; Vph = Vn
IN and VN are rated current and rated voltage at delta connection.
W1 V1
L1 L2 L3

Star-delta connection
Star-delta connection permits a reduction of the starting current, ensuring however that the resulting starting torque obtained
is higher than the load torque. Thereby it should be oberved that the torque of an asynchronous motor is directly proportional
to the square of the voltage. Motors whose rated voltage with delta connection corresponds to the mains voltage, can
be started with the star-delta method.
All motors can be supplied with windings designed for star-delta starting (for example: 400 V / 690 V Y).

General specification 12
 General specification

Three-phase squirrel-cage motors driven by frequency inverters

The motors in standard design are suitable for operation on static frequency inverters, taking into account the following
remarks:
Maximum inverter output voltage 500 V at peak voltages Û
voltages or higher stress a special insulation is required.
At square characteristic of the load torque, motors can be operated with their rated torque (exceptions are marked in the
selection tables).
In case of constant torque, the rated torque must be reduced for self-ventilated motors due to reduced supply of cooling
air. Depending on the speed range, the use of an external fan is recommendable.
For motors from frame size 280 we recommend an insulated bearing at the non-drive end.

1,2
1,1
1 1

0,9
0,8
0,7 2

0,6 3
T/T N
0,5
0,4
0,3
0,2
0,1
0
0 10 20 30 40 50 60 70 80 90
f 1 [Hz]
Forced ventilation
Self-ventilation, motors 2P
Self-ventilation, motors 4-8P

Voltage capability

Noises
Depending on the operating point, the type of inverter and the set pulse frequency, inverter-fed motors produce between
1 and 15dB(A) higher noise values than at mains operation.
Motors that are operated with a frequency over 50 Hz have more air noise. In this case we recommend the use of an externalfan

Vibration severity
When operating at high speeds (according to frequency > 60 Hz) a reduced vibration severity “B” according to
EN 60034 part 14 may be required, measured at a mains frequency of 50 Hz or 60 Hz and sinusoidal mains voltage.

13 General specification
 General specification

Cast Iron Motors

Range of motors in cast iron frame, standard-like with lubricator, PTC thermistor temperature sensor in the stator winding,
additional external protective conductor connection, available on short term in 2, 4, 6 and 8-pole design up to frame
size 355.
Overview cast iron motors
Rated power [kw]
Frame size
2-pole 4-pole 6-pole 8-pole
63 0,18 0,12 − −
63 0,25 0,18 − −
71 0,37 0,25 0,18 −
71 0,55 0,37 0,25 −
80 0,75 0,55 0,37 0,18
80 1,1 0,75 0,55 0,25
90S 1,5 1,1 0,75 0,37
90L 2,2 1,5 1,1 0,55
100L 3,0 2,2 1,5 0,75
100L − 3,0 − 1,1
112M 4,0 4,0 2,2 1,5
132S 5,5 − − −
132S 7,5 5,5 3,0 2,2
132M − − 4,0 −
132M − 7,5 5,5 3,0
160M 11 − − 4,0
160M 15 11 7,5 5,5
160L 18,5 15 11 7,5
180M 22 18,5 − −
180L − 22 15 11
200L 30 − 18,5 −
200L 37 30 22 15
225S − 37 − 18,5
225M 45 45 30 22
250M 55 55 37 30
280S 75 75 45 37
280M 90 90 55 45
315S 110 110 75 55
315M 132 132 90 75
315L 160 160 110 90
315L 200 200 132 110
355M 250 250 160 132
355M − − 200 160
355L 315 315 250 200
Gerneral data
Voltage/Connection up to 3.0 kW: 220 V / 380 V Y
from 4.0 kW: 380 V / 660 V Y
Mounting arrangements IM 1001 (B3), IM 3001 (B5), IM 3601 (B14) feet can be mounted on flange-mounted
motors
Thermistor 3 PTC built-in standard from frame 160 and above
General specification 14
 General specification

Maximum permissible axial loads without radial load

Values are valid for 50 Hz. For 60 Hz. Operation the values have to be reduced by 10%. (If additional radial forces affect, enquiry is
necessary depending on the direction of force)

Horizontal shaft
Axial load thrust [kN] Axial load tension [kN]
Frame size -1 -1 -1 -1 -1
3000 min 1500 min 1000 min 750 min 3000 min 1500 min-1 1000 min-1 750 min-1
63 0,25 0,28 - - 0,25 0,28 - -
71 0,27 0,35 0,44 - 0,27 0,35 0,44 -
80 0,38 0,47 0,59 0,62 0,38 0,47 0,59 0,62
90 0,44 0,55 0,62 0,64 0,44 0,55 0,62 0,64
100 0,61 0,75 0,88 0,89 0,61 0,75 0,88 0,89
112 1,22 1,44 1,65 1,78 1,22 1,44 1,65 1,78
132 1,50 1,78 1,82 1,92 1,50 1,78 1,82 1,92
160 1,65 2,10 2,45 2,65 1,65 2,10 2,45 2,65
180 2,10 2,60 2,90 3,17 2,10 2,60 2,90 3,17
200 2,40 3,12 3,48 3,95 2,40 3,12 3,48 3,95
225 2,72 3,48 3,89 4,33 2,72 3,48 3,89 4,33
250 3,10 3,90 4,45 4,98 3,10 3,90 4,45 4,98
280 5,30 6,30 6,70 7,10 3,10 4,40 4,30 5,02
315 5,90 7,10 7,60 8,10 3,80 5,10 5,80 3,60
355 6,10 9,80 10,50 12,50 1,85 3,90 4,70 6,00

Vertical shaft downwards

Axial load upwars [kN] Axial load downwards [kN]

Frame size
3000 min-1 1500 min-1 1000 min-1 750 min-1 3000 min-1 1500 min-1 1000 min-1 750 min-1
63 0,26 0,30 - - 0,23 0,26 - -
71 0,29 0,37 0,46 - 0,25 0,32 0,42 -
80 0,40 0,49 0,62 0,65 0,36 0,45 0,56 0,59
90 0,47 0,60 0,68 0,70 0,41 0,51 0,46 0,58
100 0,67 0,84 0,97 0,97 0,57 0,71 0,82 0,84
112 1,30 1,52 1,74 1,88 1,17 1,37 1,58 1,71
132 1,62 1,97 2,00 2,10 1,43 1,61 1,66 1,76
160 1,95 2,47 2,80 3,05 1,35 1,72 2,05 2,21
180 2,45 3,20 3,51 3,78 1,72 2,00 2,28 2,55
200 2,94 3,85 4,35 4,81 1,84 2,39 2,61 3,09
225 3,42 4,37 5,04 5,33 2,02 2,59 2,82 3,33
250 3,94 5,00 5,57 6,38 2,26 2,80 3,32 3,58
280 6,50 7,80 7,90 9,10 2,10 3,00 2,90 3,52
315 8,00 10,70 11,80 12,50 2,00 3,15 3,50 4,40
355 14,00 18,30 20,70 21,50 0,80 2,50 3,50 3,60

15 General specification
 General specification

Permissible radial loads FR in N for number of poles

without additional axial load (ball bearing) Frame size
2 4 6 8
63 300 300 - -
max. permissible radial loads in the table are valid for
71 400 400 400 -
X = 1/2 shaft length
80 610 650 750 820
90S/L 660 710 810 890
100L 920 990 1130 1240
112M 1330 1430 1640 1800
FR = Pemissible radial load in kN (without additional axial load)
X = Distance between working point of force and shaft shoulder (e.g. half pulley width)
For calculation of the radial forces see Belt drive on page 9.

General specification 16
 General specification

Anti - condensation heating

Motors which are exposed to a risk of humidity during standstill due to severe temperature variations can be equipped with
anti-condensation heating (space heaters) for an extra charge, if requested.

The supply voltage and the heating power of the strip heaters Frame size Supply voltage [V]
can be taken from the table beside. 132…200 220 2 × 40
225…250 220 2 × 50
280…315 220 2 × 65
355 220 2 × 100

17 General specification
 Technical Data

IE1 General Performance

2 pole-3000 rpm synchronous speed 50Hz
Rated Rated IFL IFL IFL
Motors
output speed 380V 400V 415V IST EFF Power Rated TST TM M of J Noise Net
level weight
type IFL % factor torque TFL TFL kgm 2
rpm (AMP) (AMP) (AMP) Nm dB(A) kg
HC-801-2 0.75 2840 1.8 1.7 1.67 5.5 75.5 0.83 2.5 2.3 2.6 0.0008 67 14
HC-802-2 1.1 2840 2.6 2.5 2.4 5.6 76.2 0.84 3.7 2.3 2.6 0.0009 67 15
HC-90S-2 1.5 2850 3.4 3.2 3.1 6.1 79.5 0.85 5 2.5 2.9 0.0012 72 20
HC-90L-2 2.2 2850 4.8 4.6 4.4 6.1 81.7 0.85 7.4 2.7 2.9 0.0014 72 24
HC-100L-2 3 2880 6.3 6 5.8 6.5 83.1 0.87 10 2.7 2.9 0.0039 76 30
HC-112M1-2 4 2880 8.2 7.8 7.6 6.5 84.2 0.88 13.3 2.6 2.9 0.0055 77 38
HC-112M2-2 5.5 2880 11.1 10.5 10.2 7.7 85.7 0.88 13.3 2.7 3.2 0.0076 78 43
HC-132S1-2 5.5 2900 11.1 10.5 10.2 6.9 85.9 0.88 18.1 2.3 2.6 0.011 80 57
HC-132S2-2 7.5 2900 14.9 14.2 13.5 6.9 87.2 0.88 24.5 2.5 2.8 0.013 80 61
HC-132M-2 11 2910 21.4 20.4 19.7 6.2 88.4 0.88 36.2 2.2 2.4 0.028 83 73
HC-160M1-2 11 2930 21.1 20.1 19.4 6.7 88.7 0.89 35.8 2.6 2.9 0.038 86 101
HC-160M2-2 15 2930 28.6 27.2 26.2 6.7 89.5 0.89 48.8 2.6 2.9 0.045 86 111
HC-160L-2 18.5 2930 34.6 32.9 31.8 6.8 90.2 0.90 60.4 2.5 2.8 0.055 86 126
HC-180M-2 22 2940 41 38.9 37.6 6.6 90.6 0.90 71.4 2.6 2.8 0.076 89 176
HC-200L1-2 30 2950 55.4 52.6 50.7 6.5 91.5 0.90 97.2 2.5 2.7 0.124 92 226
HC-200L2-2 37 2950 67.9 64.5 62.2 6.5 92.0 0.90 119.8 2.4 2.6 0.139 92 245
HC-225M-2 45 2970 82.1 78 75.3 6.8 92.5 0.90 144.8 2.4 2.6 0.233 92 280
HC-250M1-2 55 2970 99.6 94.6 91.3 6.8 93.2 0.90 177 2.5 2.8 0.312 93 379
HC-250M2-2 75 2970 135.1 128.4 123.8 6.5 93.7 0.90 241.3 2.3 3.2 0.412 94 466
HC-280S-2 75 2970 134.8 128.1 123.5 6.7 93.9 0.90 241.3 2.4 2.7 0.597 94 512
HC-280M1-2 90 2970 159.5 151.5 146.1 6.7 94.2 0.91 289.5 2.4 2.7 0.675 94 578
HC-280M2-2 110 2970 194.7 185 178.3 6.5 94.3 0.91 353.9 2 2.5 0.86 96 733
HC-315S-2 110 2980 194.6 184.9 178.2 6.6 94.4 0.91 352.7 2 2.5 1.18 96 845
HC-315M-2 132 2980 233 221.4 213.4 6.6 94.6 0.91 423.2 2.1 2.5 1.55 96 942
HC-315L1-2 160 2980 282.1 270 258.4 6.7 94.7 0.91 513 1.9 2.4 1.76 99 1019
HC-315L2-2 200 2980 347.7 330.1 318.4 6.7 95.0 0.92 641.2 1.9 2.4 2.02 99 1177
HC-355M-2 250 2980 432.3 410.8 395.9 6.5 95.5 0.92 801.5 1.6 2.3 3.56 103 1740
HC-355L-2 315 2980 543 515.9 497.3 6.5 95.8 0.92 1010 1.6 2.3 4.1 103 1920

IFL = full load current IST = locked rotor current TST = locked rotor torque TM = maximum torque TFL = full load torque

Technical Data 18
 Technical Data

IE1 General Performance

4 pole-1500 rpm synchronous speed 50Hz

Motors Rated Rated IFL IFL IFL Power Rated TST M of J Noise Net
output speed 380V 400V 415V IST EFF TM level weight
type IFL % factor torque TFL TFL kgm2
rpm (AMP) (AMP) (AMP) Nm dB(A) kg
HC-80M1-4 0.55 1390 1.6 1.5 1.4 5.5 71.4 0.75 3.8 2.2 2.4 0.002 58 13
HC-80M2-4 0.75 1390 2.1 2 1.9 5.6 73.5 0.76 5.2 2.2 2.4 0.002 58 14
HC-90S-4 1.1 1400 2.9 2.7 2.6 5.4 76.2 0.77 7.5 2.2 2.5 0.002 61 20
HC-90L-4 1.5 1400 3.8 3.5 3.4 5.2 78.7 0.78 10.2 2.4 2.6 0.003 61 23
HC-100L1-4 2.2 1420 5.1 4.9 4.7 6.0 81.0 0.81 14.8 2.3 2.6 0.007 64 29
HC-100L2-4 3 1420 6.8 6.4 6.2 6.1 82.7 0.82 20.2 2.3 2.7 0.007 64 33
HC-112M-4 4 1440 8.8 8.4 8.1 6.5 84.5 0.82 26.5 2.3 2.8 0.01 65 40
HC-132S-4 5.5 1440 11.7 11.2 10.8 6.8 85.7 0.83 36.5 2.3 2.9 0.021 7 59
HC-132M1-4 7.5 1440 15.6 14.8 14.3 6.5 87.1 0.84 49.8 2.4 3.0 0.03 71 69
HC-132M2-4 11 1440 22.6 21.4 20.7 6.8 88.4 0.84 73 2.2 2.7 0.057 75 99
HC-160M-4 11 1460 22.5 21.3 20.6 6.9 88.6 0.84 72 2.3 2.9 0.075 75 109
HC-160L-4 15 1460 30.3 28.5 27.5 6.8 89.5 0.85 98.2 2.3 2.9 0.092 75 130
HC-180M-4 18.5 1470 36.2 34.4 33.2 6.4 90.2 0.86 120.2 2.3 2.9 0.139 76 165
HC-180L-4 22 1470 42.9 40.7 39.3 6.9 90.7 0.86 143 2.3 2.9 0.158 76 180
HC-200L-4 30 1470 57.5 54.7 52.7 6.8 92.1 0.86 195 2.4 2.9 0.262 79 240
HC-225S-4 37 1480 69.7 66.2 64.6 6.5 92.7 0.87 238.9 2.2 2.7 0.406 81 278
HC-225M-4 45 1480 84.5 80.3 77.4 6.3 93.0 0.87 290.5 2.3 2.5 0.469 81 308
HC-250M1-4 55 1480 103 97.8 94.3 6.4 93.3 0.87 355.1 2.2 2.5 0.66 83 402
HC-250M2-4 75 1480 138.4 131.4 126.7 6.2 93.6 0.88 483.9 2.3 2.6 0.88 86 488
HC-280S-4 75 1480 138.1 131.1 126.4 6.8 93.8 0.88 483.9 2.1 2.8 1.12 86 540
HC-280M1-4 90 1480 165 157 152 6.9 94.1 0.88 580.7 2.2 2.7 1.46 86 615
HC-280M2-4 110 1480 201 191 184 6.5 94.5 0.89 709.8 2.1 2.3 2.68 93 717
HC-315S-4 110 1480 200.5 190.5 183.6 6.5 94.7 0.88 709.8 1.9 2.7 3.11 93 870
HC-315M-4 132 1480 240 228 220 6.8 95.0 0.88 851.8 2.3 3.2 3.29 93 990
HC-315L1-4 160 1480 287 273 263 6.6 95.2 0.89 1032 2.6 3.0 3.79 97 1053
HC-315L2-4 200 1480 358 340 328 6.4 95.4 0.89 1290 2.2 2.8 4.49 97 1243
HC-355M-4 250 1490 441 419 405 6.2 95.6 0.90 1603 1.9 2.9 5.67 101 1745
HC-355L-4 315 1490 555 527 509 6.1 95.8 0.90 2020 2.1 3.1 6.66 101 1957

IFL = full load current IST = locked rotor current TST = locked rotor torque TM = maximum torque TFL = full load torque

19 Technical Data
 Technical Data

IE1 General Performance

6 pole-1000 rpm synchronous speed 50Hz

Motors Rated Rated IFL IFL 1FL Power Rated M of J Noise Net
output speed 380V 400V 415V IST EFF TST TM level weight
type IFL % factor torque TFL TFL kgm2 dB(A) kg
rpm (AMP) (AMP) (AMP) Nm
HC-80M1-6 0.37 890 1.3 1.2 1.1 4.4 62.5 0.70 4 1.9 2.3 0.002 54 14
HC-80M2-6 0.55 890 1.8 1.7 1.6 4.5 65.0 0.72 5.9 2.1 2.4 0.003 54 16
HC-90S-6 0.75 910 2.3 2.2 2.1 4.1 69.1 0.72 7.9 2.3 2.7 0.003 57 20
HC-90L-6 1.1 910 3.2 3 2.9 4.6 72.0 0.73 11.5 2.3 2.7 0.004 57 23
HC-100L-6 1.5 920 4.1 3.9 3.7 5 76.0 0.75 15.6 2.4 2.8 0.007 61 29
HC-112M-6 2.2 940 5.6 5.3 5.1 5.2 79.1 0.76 22.4 2.1 2.5 0.014 65 38
HC-132S-6 3 960 7.4 7 6.8 5.6 81.3 0.76 29.9 1.9 2.5 0.029 69 54
HC-132M1-6 4 960 9.7 9.2 8.9 6.2 82.3 0.76 39.8 2.1 2.7 0.036 69 62
HC-132M2-6 5.5 960 12.8 12.2 11.7 6.5 84.7 0.77 54.7 2.3 2.8 0.045 69 69
HC-160M-6 7.5 970 17.1 16.2 15.6 5.6 86.6 0.77 73.9 2.0 2.6 0.088 73 103
HC-160L-6 11 970 24.5 23.2 22.4 5.8 87.6 0.78 108.3 2.1 2.4 0.116 73 121
HC-180L-6 15 970 31.6 30.1 28.9 5.7 89.0 0.81 147.7 2.0 2.4 0.207 73 173
HC-200L1-6 18.5 970 38.5 36.6 35.2 6.7 90.2 0.81 182.2 2.2 2.8 0.315 76 221
HC-200L2-6 22 970 44.7 42.5 40.9 6.6 90.2 0.83 216.7 2.3 2.9 0.36 76 236
HC-225M-6 30 980 59.3 56.4 54.3 6.8 91.5 0.84 292.5 2.2 2.7 0.547 76 301
HC-250M-6 37 980 70.1 67.4 64.9 6.2 92.2 0.86 360.7 2.0 2.5 0.834 78 370
HC-280S-6 45 980 86 82 79 6.1 92.5 0.86 438.7 1.9 2.5 1.39 80 478
HC-280M1-6 55 980 105 100 96 6.7 92.9 0.86 536.2 2.1 2.7 1.65 80 535
HC-280M2-6 75 985 140 133 128 5.8 93.6 0.87 727.2 2.1 2.3 3.21 85 682
HC-315S-6 75 990 142 135 129 6.5 93.7 0.86 723.8 2.0 2.7 4.11 85 790
HC-315M-6 90 990 170 161 155 6.2 93.9 0.86 868.6 2.0 2.6 4.28 85 880
HC-315L1-6 110 990 206 196 188 6 94.5 0.86 1062 1.9 2.7 5.45 85 997
HC-315L2-6 132 990 244 232 223 5.8 94.6 0.87 1274 2.0 2.7 6.12 85 1103
HC-355M1-6 160 990 291 276 266 6.3 95.1 0.88 1544 1.6 2.8 8.85 92 1400
HC-355M2-6 200 990 362 343 331 6.6 95.4 0.88 1930 2.0 2.9 9.55 92 1780
HC-355L-6 250 990 451 249 413 6.5 95.7 0.88 2413 1.6 3.0 10.3 92 2050

IFL = full load current IST = locked rotor current TST = locked rotor torque TM = maximum torque TFL = full load torque

Technical Data 20
 Technical Data

IE1 General Performance

8 pole-750 rpm synchronous speed 50Hz

Motors Rated Rated IFL IFL IFL Power Rated TST TM M of J Noise Net
output speed 380V 400V 415V IST EFF level weight
type IFL % factor torque TFL TFL kgm2
rpm (AMP) (AMP) (AMP) Nm dB(A) kg
HC-80M1-8 0.18 630 0.88 0.83 0.8 2.9 51.2 0.61 2.8 2 2.2 0.002 52 14
HC-80M2-8 0.25 640 1.15 1.09 1.05 3 54.2 0.61 3.7 2.1 2.4 0.003 52 16
HC-90S-8 0.37 660 1.48 1.41 1.36 3.4 62.2 0.61 5.4 2 2.2 0.004 56 20
HC-90L-8 0.55 660 2.16 2.06 1.98 3.5 63.3 0.61 8 2.1 2.3 0.004 56 23
HC-100L1-8 0.75 690 2.41 2.29 2.21 3.5 70.5 0.67 10.4 2 2.2 0.008 59 31
HC-100L2-8 1.1 690 3.35 3.18 3.06 3.6 72.4 0.69 15.2 2.2 2.4 0.01 59 35
HC-112M-8 1.5 690 4.4 4.2 4 3.9 74.5 0.70 20.8 2.4 2.6 0.017 61 38
HC-132S-8 2.2 710 5.9 5.6 5.4 4.3 79.3 0.71 29.6 2.3 2.5 0.031 64 52
HC-132M-8 3 710 7.8 7.4 7.1 4.4 80.1 0.73 40.4 2.2 2.4 0.01 64 61
HC-160M1-8 4 720 10.2 9.7 9.3 4.4 81.6 0.73 53.1 2.2 2.5 0.075 68 90
HC-160M2-8 5.5 720 13.6 12.9 12.4 5 83.3 0.74 73 2.2 2.4 0.093 68 102
HC-160L-8 7.5 720 17.7 16.8 16.2 5.7 85.9 0.75 99.5 2.1 2.3 0.126 68 122
HC-180L-8 11 730 25.4 24.1 23.2 5.6 87.8 0.75 144 2.3 2.5 0.203 70 150
HC-200L-8 15 730 34 32.3 31.1 5.5 88.3 0.76 196.3 2.1 2.4 0.339 73 212
HC-225S-8 18.5 730 41 39 37.5 5.6 90.2 0.76 242.1 2.2 2.6 0.491 73 285
HC-225M-8 22 740 47.2 44.8 43.2 5.4 90.8 0.78 284 2.1 2.4 0.547 73 385
HC-250M-8 30 740 63.3 60.1 57.9 5.3 91.2 0.79 387.3 2.2 2.5 0.83 75 378
HC-280S-8 37 740 77.5 73.6 71 5.6 91.8 0.79 477.7 2.3 2.7 1.39 76 485
HC-280M-8 45 740 94.1 89.4 86.1 5.2 92.0 0.79 581 2.1 2.8 1.65 76 568
HC-315S-8 55 740 110.8 105.3 101.5 5.7 93.1 0.81 710.1 1.9 2.5 4.79 82 745
HC-315M-8 75 740 150.1 142.6 137.5 5.9 93.7 0.81 968.3 2.1 2.8 5.58 82 805
HC-315L1-8 90 740 177.4 168.5 162.4 6.2 94.0 0.82 1162 2.3 2.9 6.37 82 998
HC-315L2-8 110 740 216.4 205.6 198.1 6 94.2 0.82 1420 2.2 2.8 7.23 82 1175
HC-355M1-8 132 740 259.4 246.4 237.5 6.4 94.3 0.82 1704 1.9 2.7 7.55 90 1580
HC-355M2-8 160 740 313.7 298 287.3 6.3 94.5 0.82 2066 1.7 2.6 11.73 90 1680
HC-355L-8 200 740 386.2 366.9 353.6 6.5 94.8 0.83 2582 1.8 2.9 12.86 90 1995

IFL = full load current IST = locked rotor current TST = locked rotor torque TM = maximum torque TFL = full load torque

21 Technical Data
 Technical Data

Dimensions foot mount B3

HC-80 ~ 132
AD’

LG 2-KK AG

GD
ED DH

HD
AC

HA
D

H
E C B K AA
BB A
L AA

HC -160 ~ 200 AD’

LG 2-KK AG

F
ED GD
DH

HD
G
AC

HA
H
E C B K AA
BB A
L AB

HC-225 ~ 280
AD’
LG 2-KK AG

F
GD

ED
DH
HD
G

HA
H

E C B K AA
BB
AB
L

HC-315 ~ 355
AD’
LG AG
2-KK

F
GD

ED
HD

DH
G

D
H
HA

E C B K AA
BB A
AB

Technical Data 22
 Technical
TechnicalData
Data

Dimensions foot mount B3

Frame size A AA AB AC AD' AG B BB C D DH E ED F G GD H HA HD K KK L LG
80M 125 34 160 175 140 51 100 130 50 19 M6 × 16 40 25 6 15.5 6 80 10 230 10 M25 × 1.5 295 106
90S 140 36 180 190 150 60 100 135 56 24 M8 × 19 50 40 8 20 7 90 12.5 260 10 M25 × 1.5 320 124
90L 140 36 180 190 150 60 125 160 56 24 M8 × 19 50 40 8 20 7 90 12.5 260 10 M25 × 1.5 345 124
100L 160 40 200 215 160 60 140 182 63 28 M10 × 22 60 45 8 24 7 100 14 275 12 M25 × 1.5 385 140
112M 190 45 230 236 185 75 140 195 70 28 M10 × 22 60 45 8 24 7 112 14 310 12 M32 × 1.5 410 145
132S 216 52 265 275 205 75 140 205 89 38 M12 × 28 80 63 10 33 8 132 16 350 12 M32 × 1.5 480 169
132M 216 52 265 275 205 75 178 245 89 38 M12 × 28 80 63 10 33 8 132 16 350 12 M32 × 1.5 520 196
160M 254 65 320 330 250 95 210 260 108 42 M16 × 36 110 90 12 37 8 160 19 425 14.5 M40 × 1.5 610 270
160L 254 65 320 330 250 95 254 305 108 42 M16 × 36 110 90 12 37 8 160 19 425 14.5 M40 × 1.5 655 270
180M 279 74 350 380 270 95 241 297 121 48 M16 × 36 110 90 14 42.5 9 180 22 460 14.5 M40 × 1.5 680 277
180L 279 74 350 380 270 95 279 327 121 48 M16 × 36 110 90 14 42.5 9 180 22 460 14.5 M40 × 1.5 720 277
200L 318 75 395 420 325 120 305 370 133 55 M20 × 42 110 90 16 49 10 200 25 515 18.5 M50 × 1.5 760 300
225S(4-8P) 356 75 436 465 335 120 286 355 149 60 M20 × 42 140 110 18 53 11 225 28 560 18.5 M50 × 1.5 825 340
225M(2P) 356 75 436 465 335 120 311 380 149 55 M20 × 42 110 90 16 49 10 225 28 560 18.5 M50 × 1.5 820 310
225M(4-8P) 356 75 435 465 335 120 311 380 149 60 M20 × 42 140 110 18 53 11 225 28 560 18.5 M50 × 1.5 850 340
250M(2P) 406 88 495 520 370 160 349 440 168 60 M20 × 42 140 110 18 53 11 250 33 620 24 M63 × 1.5 925 353
250M1(4-8P) 406 88 495 520 370 160 349 440 168 65 M20 × 42 140 110 18 58 11 250 33 620 24 M63 × 1.5 925 353
250M2(4P) 406 88 495 520 370 160 349 440 168 70 M20 × 42 140 110 20 62.5 12 250 33 620 24 M63 × 1.5 935 353
280S(2P) 457 103 550 570 400 160 368 495 190 65 M20 × 42 140 110 18 58 11 280 35 685 24 M63 × 1.5 960 350
280S(4-8P) 457 103 550 570 400 160 368 495 190 75 M20 × 42 140 110 20 67.5 12 280 35 685 24 M63 × 1.5 975 350
280M(2P) 457 103 550 570 400 160 419 535 190 65 M20 × 42 140 110 18 58 11 280 35 685 24 M63 × 1.5 1000 350
280M1(4-8P) 457 103 550 570 400 160 419 535 190 75 M20 × 42 140 110 20 67.5 12 280 35 685 24 M63 × 1.5 1015 350
280M2(4-8P) 457 103 550 570 400 160 419 535 190 80 M20 × 42 170 140 22 71 14 280 35 685 24 M63 × 1.5 1060 380
315S(2P) 508 120 630 650 495 195 406 515 216 65 M20 × 42 140 110 18 58 11 315 45 820 28 M63 × 1.5 1160 387
315M(2P) 508 120 630 650 495 195 457 625 216 65 M20 × 42 140 110 18 58 11 315 45 820 28 M63 × 1.5 1270 387
315L(2P) 508 120 630 650 495 195 508 625 216 65 M20 × 42 140 110 18 58 11 315 45 820 28 M63 × 1.5 1270 387
315S(4-8P) 508 120 630 650 495 195 406 515 216 80 M20 × 42 170 140 22 71 14 315 45 820 28 M63 × 1.5 1190 417
315M(4-8P) 508 120 630 650 495 195 457 625 216 80 M20 × 42 170 140 22 71 14 315 45 820 28 M63 × 1.5 1300 417
315L(4-8P) 508 120 630 650 495 195 508 625 216 80 M20 × 42 170 140 22 71 14 315 45 820 28 M63 × 1.5 1300 417
355M(2P) 610 125 735 735 640 330 560 775 254 75 M24 × 50 140 110 20 67.5 12 355 49 1000 28 M63 × 1.5 1500 420
355L(2P) 610 125 735 735 640 330 630 775 254 75 M24 × 50 140 110 20 67.5 12 355 49 1000 28 M63 × 1.5 1500 420
355M(4-8P) 610 125 735 735 640 330 560 775 254 95 M24 × 50 170 140 25 86 14 355 49 1000 28 M63 × 1.5 1530 450
* 355M(4-8P) 610 125 735 735 640 330 560 775 254 100 M24 × 50 210 160 28 90 16 355 49 1000 28 M63 × 1.5 1570 490
355L(4-8P) 610 125 735 735 640 330 630 775 254 95 M24 × 50 170 140 25 86 14 355 49 1000 28 M63 × 1.5 1530 450
* 355L(4-8P) 610 125 735 735 640 330 630 775 254 100 M24 × 50 210 160 28 90 16 355 49 1000 28 M63 × 1.5 1570 490

* These motors can also be supplied. Please state the dimensions of the shaft extension on order.

23 Technical Data
 Technical Data

Dimensions foot-flange mount B35

HC-80 ~ 132
AD’
LG
AG
LA
2-KK
T
S
F M

GD
ED
DH

HD
AC
N
P

HA
D

H
E C BC K AA
R BB A
L AB

HC -160 ~ 200 AD’

LG
AG
2-KK
LA
T
S
M
ED F
GD DH
AC

HD
N
P

HA
H

45
R
E C B K AA
BB A
L AB

HC-225 ~ 280
LG AD’
LA 2-KK AG

S
5
22.

M
F
GD
AC

ED
DH HD
N
P

D
HA
H

R K AA
E C B A
BB AB
L

HC-315 ~ 355 AD’

LG AG
2-KK
LA
T

F
GD

ED
22.5

HD

DH
AC
N
P

D
HA
H

E C B K AA
BB A
L AB

Technical Data 24
 Technical
TechnicalData
Data

Dimensions foot-flange mount B35

Frame size A AA AB AC AD' AG B BB C D DH E ED F G GD H HA HD K KK L LG LA M N P S T
80M 125 34 160 175 140 51 100 130 50 19 M6 × 16 40 25 6 15.5 6 80 10 230 10 M25 × 1.5 295 106 12 165 130 200 12 3.5
90S 140 36 180 190 150 60 100 135 56 24 M8 × 19 50 40 8 20 7 90 12.5 260 10 M25 × 1.5 320 124 12 165 130 200 12 3.5
90L 140 36 180 190 150 60 125 160 56 24 M8 × 19 50 40 8 20 7 90 12.5 260 10 M25 × 1.5 345 124 12 165 130 200 12 3.5
100L 160 40 200 215 160 60 140 182 63 28 M10 × 22 60 45 8 24 7 100 14 275 12 M25 × 1.5 385 140 14 215 180 250 14.5 4
112M 190 45 230 236 185 75 140 195 70 28 M10 × 22 60 45 8 24 7 112 14 310 12 M32 × 1.5 410 145 14 215 180 250 14.5 4
132S 216 52 265 275 205 75 140 205 89 38 M12 × 28 80 63 10 33 8 132 16 350 12 M32 × 1.5 480 169 14 265 230 300 14.5 4
132M 216 52 265 275 205 75 178 245 89 38 M12 × 28 80 63 10 33 8 132 16 350 12 M32 × 1.5 520 169 14 265 230 300 14.5 4
160M 254 65 320 330 250 95 210 260 108 42 M16 × 36 110 90 12 37 8 160 19 425 14.5 M40 × 1.5 610 270 15 300 250 350 18.5 5
160L 254 65 320 330 250 95 254 305 108 42 M16 × 36 110 90 12 37 8 160 19 425 14.5 M40 × 1.5 655 270 15 300 250 350 18.5 5
180M 279 74 350 380 270 95 241 297 121 48 M16 × 36 110 90 14 42.5 9 180 22 460 14.5 M40 × 1.5 680 277 15 300 250 350 18.5 5
180L 279 74 350 380 270 95 279 327 121 48 M16 × 36 110 90 14 42.5 9 180 22 460 14.5 M40 × 1.5 720 277 15 300 250 350 18.5 5
200L 318 75 395 420 325 120 305 370 133 55 M20 × 42 110 90 16 49 10 200 25 515 18.5 M50 × 1.5 760 300 17 350 300 400 18.5 5
225S(4-8P) 356 75 436 465 335 120 286 355 149 60 M20 × 42 140 110 18 53 11 225 28 560 18.5 M50 × 1.5 825 340 20 400 350 450 18.5 5
225M(2P) 356 75 436 465 335 120 311 380 149 55 M20 × 42 110 90 16 49 10 225 28 560 18.5 M50 × 1.5 820 310 20 400 350 450 18.5 5
225M(4-8P) 356 75 436 465 335 120 311 380 149 60 M20 × 42 140 110 18 53 11 225 28 560 18.5 M50 × 1.5 850 340 20 400 350 450 18.5 5
250M(2P) 406 88 495 520 370 160 349 440 168 60 M20 × 42 140 110 18 53 11 250 33 620 24 M63 × 1.5 925 353 20 500 450 550 18.5 5
250M1(4-8P) 406 88 495 520 370 160 349 440 168 65 M20 × 42 140 110 18 58 11 250 33 620 24 M63 × 1.5 925 353 20 500 450 550 18.5 5
250M2(4P) 406 88 495 520 370 160 349 440 168 70 M20 × 42 140 110 20 62.5 12 280 33 620 24 M63 × 1.5 935 353 20 500 450 550 18.5 5
280S(2P) 457 103 550 570 400 160 368 495 190 65 M20 × 42 140 110 18 58 11 280 35 685 24 M63 × 1.5 960 350 22 500 450 550 18.5 5
280S(4-8P) 457 103 550 570 400 160 368 495 190 75 M20 × 42 140 110 20 67.5 12 280 35 685 24 M63 × 1.5 975 350 22 500 450 550 18.5 5
280M(2P) 457 103 550 570 400 160 419 535 190 65 M20 × 42 140 110 18 58 11 280 35 685 24 M63 × 1.5 1000 350 22 500 450 550 18.5 5
280M1(4-8P) 457 103 550 570 400 160 419 535 190 75 M20 × 42 140 110 20 67.5 12 280 35 685 24 M63 × 1.5 1015 350 22 500 450 550 18.5 5
280M2(4-8P) 457 103 550 570 400 160 419 535 190 80 M20 × 42 170 140 22 71 14 280 35 685 24 M63 × 1.5 1160 380 22 500 450 550 18.5 5
315S(2P) 508 120 630 650 495 195 406 515 216 65 M20 × 42 140 110 18 58 11 315 45 820 28 M63 × 1.5 1060 387 24 600 550 660 24 6
315M(2P) 508 120 630 650 495 195 457 625 216 65 M20 × 42 140 110 18 58 11 315 45 820 28 M63 × 1.5 1270 387 24 600 550 660 24 6
315L(2P) 508 120 630 650 495 195 508 625 216 65 M20 × 42 140 110 18 58 11 315 45 820 28 M63 × 1.5 1270 387 24 600 550 660 24 6
315S(4-8P) 508 120 630 650 495 195 406 515 216 80 M20 × 42 170 140 22 71 14 315 45 820 28 M63 × 1.5 1190 417 24 600 550 660 24 6
315M(4-8P) 508 120 630 650 495 195 457 625 216 80 M20 × 42 170 140 22 71 14 315 45 820 28 M63 × 1.5 1300 417 24 600 550 660 24 6
315L(4-8P) 508 120 630 650 495 195 508 625 216 80 M20 × 42 170 140 22 71 14 315 45 820 28 M63 × 1.5 1300 417 24 600 550 660 24 6
355M(2P) 610 125 735 735 640 330 560 775 254 75 M24 × 50 140 110 20 67.5 12 355 49 1000 28 M63 × 1.5 1500 420 25 740 680 800 24 6
355L(2P) 610 125 735 735 640 330 630 775 254 75 M24 × 50 140 110 20 67.5 12 355 49 1000 28 M63 × 1.5 1500 420 25 740 680 800 24 6
355M(4-8P) 610 125 735 735 640 330 560 775 254 95 M24 × 50 170 140 25 86 14 355 49 1000 28 M63 × 1.5 1530 450 25 740 680 800 24 6
355M(4-8P) 610 125 735 735 640 330 560 775 254 100 M24 × 50 210 160 28 90 16 355 49 1000 28 M63 × 1.5 1570 490 25 740 680 800 24 6
355L(4-8P) 610 125 735 735 640 330 630 775 254 95 M24 × 50 170 140 25 86 14 355 49 1000 28 M63 × 1.5 1530 450 25 740 680 800 24 6
355L(4-8P) 610 125 735 735 640 300 630 775 254 100 M24 × 50 210 160 28 90 16 355 49 1000 28 M63 × 1.5 1570 490 25 740 680 800 24 6

The 'R' dimensions is zero.

* These motors can also be supplied. Please state the dimensions of the shaft extension on order.

29 Technical Data
 Technical
TechnicalData
Data

Dimensions flange mount B5 and V1

HC-80 ~ 132
LG AD’
LA 2-KK AG
T
S
F M

GD

AD
22.5
ED GD

AC
N

G
P

E D

HC -160 ~ 200 AD’

LG AG
2-KK
LA
T
S

AD
F
GD

45
ED DH
N
P

G
AC

E M
D

R
L
LM

HC-225 ~ 280 LG AD’

LA 2-KK AG
T

S
5
AD
22.

F
GD

ED
DH
N

AC
P

D
E
M

R
L
LM

HC-315 ~ 355 AD’

LG AG
2-KK
LA
T

AD
S
F
GD

ED DH
22.5
AC
N
P

D
E
M

LM

Technical Data 26
 Technical
TechnicalData
Data

Dimensions flange mount B5 and V1

Frame size AC AD AD' AG D DH E ED F G GD KK L LA LG M N P S T

80M 175 150 140 51 19 M6 × 16 440 25 6 15.5 6 M25 × 1.5 295 12 106 165 130 200 12 3.5
90S 190 165 150 60 24 M8 × 19 50 40 8 20 7 M25 × 1.5 320 12 124 165 130 200 12 3.5
90L 190 165 150 60 24 M8 × 19 50 40 8 20 7 M25 × 1.5 345 12 124 165 130 200 12 3.5
100L 215 170 160 60 28 M10 × 22 60 45 8 24 7 M25 × 1.5 385 14 140 215 180 250 14.5 4
112M 236 195 185 75 28 M10 × 22 60 45 8 24 7 M32 × 1.5 410 14 145 215 180 250 14.5 4
132S 275 215 205 75 38 M12 × 28 80 63 10 33 8 M32 × 1.5 480 14 169 265 230 300 14.5 4
132M 275 215 205 75 38 M12 × 28 80 63 10 33 8 M32 × 1.5 520 14 169 265 230 300 14.5 4
160M 330 265 250 95 42 M16 × 36 110 90 12 37 8 M40 × 1.5 610 15 270 300 250 350 18.5 5
160L 330 265 250 95 42 M16 × 36 110 90 12 37 8 M40 × 1.5 655 15 270 300 250 350 18.5 5
180M 380 280 270 95 48 M16 × 36 110 90 14 42.5 9 M40 × 1.5 680 15 277 300 250 350 18.5 5
180L 380 280 270 95 48 M20 × 42 110 90 14 42.5 9 M40 × 1.5 720 15 277 300 250 350 18.5 5
200L 420 315 325 120 55 M20 × 42 110 90 16 49 10 M50 × 1.5 760 17 300 350 300 400 18.5 5
225S(4-8P) 465 335 335 120 60 M20 × 42 140 110 18 53 11 M50 × 1.5 825 20 340 400 350 450 18.5 5
225M(2P) 465 335 335 120 55 M20 × 42 110 90 16 49 10 M50 × 1.5 820 20 310 400 350 450 18.5 5
225M(4-8P) 465 335 335 120 60 M20 × 42 140 110 18 53 11 M50 × 1.5 850 20 340 400 350 450 18.5 5
250M(2P) 520 375 370 160 60 M20 × 42 140 110 18 53 11 M63 × 1.5 925 20 353 500 450 550 18.5 5
250M1(4-8P) 520 375 370 160 65 M20 × 42 140 110 18 58 11 M63 × 1.5 925 20 353 500 450 550 18.5 5
250M2(4P) 520 375 370 160 70 M20 × 42 140 110 20 62.5 12 M63 × 1.5 925 20 353 500 450 550 18.5 5
280S(2P) 570 405 400 160 65 M20 × 42 140 110 18 58 11 M63 × 1.5 960 22 350 500 450 550 18.5 5
280S(4-8P) 570 405 400 160 75 M20 × 42 140 110 20 67.5 12 M63 × 1.5 975 22 350 500 450 550 18.5 5
280M(2P) 570 405 400 160 65 M20 × 42 140 110 18 58 11 M63 × 1.5 1000 22 350 500 450 550 18.5 5
280M1(4-8P) 570 405 400 160 75 M20 × 42 140 110 20 67.5 12 M63 × 1.5 1015 22 350 500 450 550 18.5 5
280M2(4P) 570 405 400 160 80 M20 × 42 170 140 22 71 14 M63 × 1.5 1060 22 450 550 450 550 18.5 5
315S(2P) 650 500 495 195 65 M20 × 42 140 110 18 58 11 M63 × 1.5 1160 24 387 600 550 660 24 6
315M(2P) 650 500 495 195 65 M20 × 42 140 110 18 58 11 M63 × 1.5 1270 24 387 600 550 660 24 6
315L(2P) 650 500 495 195 65 M20 × 42 140 110 18 58 11 M63 × 1.5 1270 24 387 600 550 660 24 6
315S(4-8P) 650 500 495 195 80 M20 × 42 170 140 22 71 14 M63 × 1.5 1190 24 417 600 550 660 24 6
315M(4-8P) 650 500 495 195 80 M20 × 42 170 140 22 71 14 M63 × 1.5 1300 24 417 600 550 660 24 6
315L(4-8P) 650 500 495 195 80 M20 × 42 170 140 22 71 14 M63 × 1.5 1300 24 417 600 550 660 24 6
355M(2P)V1 735 645 640 330 75 M24 × 50 140 110 20 67.5 12 M63 × 1.5 1500 25 420 740 680 800 24 6
355L(2P)V1 735 645 640 330 75 M24 × 50 140 110 20 67.5 12 M63 × 1.5 1500 25 420 740 680 800 24 6
355M(4-8P)V1 735 645 640 330 95 M24 × 50 170 140 25 86 14 M63 × 1.5 1530 25 450 740 680 800 24 6
*355M(4-8P)V1 735 645 640 330 100 M24 × 50 210 160 28 90 16 M63 × 1.5 1570 25 490 740 680 800 24 6
355L(4-8P)V1 735 645 640 330 95 M24 × 50 170 140 25 86 14 M63 × 1.5 1530 25 450 740 680 800 24 6
*355L(4-8P)V1 735 645 640 330 100 M24 × 50 210 160 28 90 16 M63 × 1.5 1570 25 490 740 680 800 24 6

The 'R' dimensions is zero.

The motors of B5 are supplied only up to frame size 315.
* These motors can also be supplied. Please state the dimenstion of the shaft extension on order.

27 Technical Data
 Technical
TechnicalData
Data

Dimensions face-flange mount B14A and B14B

HC-80 ~ 160 B 14A

AD’
LG AG
2-KK
T

GD
ED
S

AD
DH
P
N

AC

G
M
D

R
E
L

HC-80 ~ 160 B 14B

AD’
LG AG
2-KK

T
S
GD

AD
F

ED DH
P
N

G
AC

E
D
M
R
L

Frame B14A B14B

size AC AD AD' AG D DH E ED F G GD KK L LG
M N P S T M N P S T
80M 175 150 140 51 19 M6 × 16 40 25 6 15.5 6 M25 × 1.5 295 106 100 80 120 M6 3 130 110 160 M8 3.5
90S 190 165 150 60 24 M8 × 19 50 40 8 20 7 M25 × 1.5 320 124 115 95 140 M8 3 130 110 160 M8 3.5
90L 190 165 150 60 24 M8 × 19 50 40 8 20 7 M25 × 1.5 345 124 115 95 140 M8 3 130 110 160 M8 3.5
100L 215 170 160 60 28 M10 × 22 60 45 8 24 7 M25 × 1.5 385 140 130 110 160 M8 3.5 165 130 200 M10 3.5
112M 236 195 185 75 28 M10 × 22 60 45 8 24 7 2 × M32 ×1.5 410 145 130 110 160 M8 3.5 165 130 200 M10 3.5
132S 275 215 205 75 38 M12 × 28 80 63 10 33 8 2 × M32 ×1.5 480 169 165 130 200 M10 3.5 215 180 250 M12 4
132M 275 215 205 75 38 M12 × 28 80 63 10 33 8 2 × M32 ×1.5 520 169 165 130 200 M10 3.5 215 180 250 M12 4
160M 330 265 250 95 42 M16 × 36 110 90 12 37 8 2 × M40 ×1.5 610 270 215 180 250 M12 4 - - - - -
160L 330 265 250 95 42 M16 × 36 110 90 12 37 8 2 × M40 ×1.5 655 270 215 180 250 M12 4 - - - - -

The 'R' dimensions is zero.

Technical Data 28
 Technical Data

Top terminal box

HC-80 ~ 132 HC-160 ~ 225 HC-250 ~ 280

1 2 3 4 5 3 1 4 2 5 1 2 4 3 5

B
B

A
C A
C A C

HC-315 HC-355
1 4 2 3 5
1 4 2 3 5
B

A C A C

METRIC PG
Frame size A B C 1 2 3 4 5 GRAND GLAND
SIZE SIZE
HC-80 107 107 67 M5 × 16 M5 × 25 M5 × 16 M5 × 12 M4 M25 × 1.5 PG16
HC-90-100 115 115 75 M5 × 16 M5 × 25 M5 × 16 M5 × 12 M4 M25 × 1.5 PG16
HC-112-132 124 130 80 M5 × 16 M5 × 25 M5 × 20 M5 × 16 M5 2 × M32 × 1.5 2 × PG21
HC-160-180 184 163 95 M6 × 16 M6 × 25 M6 × 16 M6 × 12 M6 2 × M40 × 1.5 2 × PG29
HC-200-225 215 192 112 M8 × 25 M8 × 35 M8 × 25 M8 × 16 M8 2 × M50 × 1.5 2 × PG36
HC-250-280 249 220 134 M8 × 25 M8 × 35 M8 × 25 M8 × 16 M10 2 × M63 × 1.5 2 × PG42
HC-315 323 283 180 M10 × 25 M8 × 45 M10 × 25 M10 × 20 M12 2 × M63 × 1.5 2 × PG48
HC-355 365 490 285 M8 × 30 M12 × 80 M12 × 30 M12 × 25 M16 2 × M63 × 1.5 2 × PG48

29 Technical Data
 Technical
TechnicalData
Data

Side terminal box

HC-80 ~ 100 HC-112 ~ 132 HC-160 ~ 225
4 3 2 1 5 1 2 3 4 5 1 4 3 2 5

B
B
B

A C A B A C

HC-250-315 HC-355
1 2 3 4 5
4 2 3 1 5

B
B

A C A C

METRIC PG
Frame size A B C 1 2 3 4 5 GRAND GLAND
SIZE SIZE
HC-80 95 95 56 M5 × 16 M5 × 25 M5 × 16 M5 × 12 M4 M25 × 1.5 PG16
HC-90-100 105 109 56 M5 × 16 M5 × 25 M5 × 16 M5 × 12 M4 M25 × 1.5 PG16
HC-112-132 117 125 65 M5 × 16 M5 × 25 M5 × 20 M5 × 16 M5 2 × M32 × 1.5 2 × PG21
HC-160-180 155 177 87 M6 × 16 M6 × 25 M6 × 16 M6 × 12 M6 2 × M40 × 1.5 2 × PG29
HC-200-225 179 215 107 M6 × 25 M8 × 35 M8 × 20 M8 × 16 M8 2 × M50 × 1.5 2 × PG36
HC-250-280 217 261 120 M6 × 30 M8 × 35 M8 × 30 M10 × 20 M10 2 × M63 × 1.5 2 × PG42
HC-315 279 331 165 M8 × 35 M10 × 45 M10 × 30 M10 × 20 M12 2 × M63 × 1.5 2 × PG48
HC-355 334 410 278 M8 × 30 M12 × 80 M12 × 30 M10 × 25 M20 2 × M63 × 1.5 2 × PG48

Technical Data 30
 Technical
TechnicalData
Data

Bearing & Iubrication

Frame size DE NDE d D B
HC-80 6204 ZZ C3 6204 ZZ C3 20 47 14
HC-90 6205 ZZ C3 6205 ZZ C3 25 52 15 B

HC-100 6206 ZZ C3 6206 ZZ C3 30 62 16

HC-112 6306 ZZ C3 6306 ZZ C3 30 72 19
HC-132 6308 ZZ C3 6308 ZZ C3 40 90 23
HC-160 6309 C3 6309 C3 45 100 25
HC-180 6311 C3 6311 C3 55 120 29
HC-200 6312 C3 6312 C3 60 130 31
HC-225 6313 C3 6313 C3 65 140 33
HC-250 (Horizontal) 6314 C3 6314 C3 70 150 35
HC-250 (Vertical) 6314 C3 7314 70 150 35
HC-280-2P (Horizontal) 6314 C3 6317 C3 70 150 35

d
HC-280-2P (Vertical) 6314 C3 7317 70 150 35
HC-280 4-8P (Horizontal) 6317 C3 6317 C3 85 180 41
HC-280 4-8P (Vertical) 6317 C3 7317 85 180 41
HC-315 2P (Horizontal) 6316 C3 6316 C3 80 170 39
HC-315 2P (Vertical) 6316 C3 7316 80 170 39
HC-315 4-8P (Horizontal) N319 6319 C3 95 200 45
HC-315 4-8P (Vertical) N319 7319 95 200 45
HC-355 2P (Horizontal) 6319 C3 6319 C3 95 200 45
HC-355 2P (Vertical) 6319 C3 7319 95 200 45
HC-355 4-8P (Horizontal) N322 6322 C3 110 240 50
HC-355 4-8P (Vertical) N322 7322 110 240 50

• HC motors are equipped with bearings from excellent manufacturers.

• In general the bearings have C3 clearances.
• Motors of frame sizes 80-132 are fitted with life-lubricated bearing.
• Motors of frame sizes 160-355 are fitted with open bearings and regreasing device. Depending on the useful life of grease,
open bearings must be regreased in good time so that the scheduled bearing service life is reached.

Frame Drive Non-drive Regreasing period hours for Quantily of

size end bearing end bearing grease in
bearing chamber
<3600r/min <1800r/min <1200r/min grams
HC3-160 6309 C3 6309 C3 6000 12000 18000 13
HC3-180 6311 C3 6311 C3 4000 11000 16000 15
HC3-200 6312 C3 6312 C3 3500 8500 13000 20
HC3-225 6313 C3 6313 C3 3000 6000 9000 22
HC3-250 6314 C3 6314 C3 2000 5000 8000 23
HC3-280 2P 6314 C3 6314 C3 1200 - - 30
HC3-280 4-8P 6317 C3 6317 C3 - 4000 6000 30
HC3-315 2P 6316 C3 6316 C3 1200 - - 30
HC3-315 4-8P N319 6319 C3 - 2000 3000 45
HC3-355 2P 6319 C3 6319 C3 1200 - - 30
HC3-355 4-8P N322 6322 C3 - 1400 2200 60

Note:
1.Vertical motors should be greased twice as often as horizontal motors.

• HASCON reserves right to make changes to this brochure without notice.

31 Technical Data
www.tngroup.co.th
@tnmotor Transmissiontngroup
Version 2022/1