Conbextra EP10(M) constructive solutions

Moisture insensitive epoxy resin injection

material
Uses

Conbextra EP10(M) is a two part epoxy resin system for grout-

Exotherm
ing gaps ranging from 0.25mm to 10mm. It is an all liquid
system consisting of a base and hardener. All epoxy systems will develop a temperature rise on mixing.
Its extent will be a function of the volume to surface ratio, the
Advantages
ambient temperature as well as the mass and thermal conduc-
Moisture insensitive tivity of the surrounding materials. Contact Fosroc for specific
data on each product.
 Low creep characteristics
Application instructions
 High compressive, tensile and flexural strengths
Prepare the surface and seal the cracks with a sealing com-
 Fast, convenient pumping with early strength gain
pound which can also be used for bonding injection nipples.
 Withstands a wide range of chemicals Depending on the crack width and depth the distance between
nipples should be 200 to 500 mm.
Technical support
Mixing and placing
Fosroc offers a comprehensive range of high performance, high
quality concrete repair and construction products. In addition, Pour all the contents of the hardener pack into the base con-
Fosroc offers technical support service to specifiers, end-users tainer. Mix using a slow speed power mixer for 60 seconds.
and contractors, as well as on-site technical assistance in loca- Use a suitable pressure pump for injecting the material into
tions all over the country. cracks. After 24 hours remove the nipples and seal the holes
or voids with more sealing the compound and allow to cure.
Properties
For filling cracks of more than 10mm and using
The following results are typical for the hardener grout at 30
as an epoxy mortar
deg.C.
Conbextra EP10(M) has to be mixed with clean graded quartz
Test method Typical result sand from 1:3 to 1:6 parts by weight depending on the con-
sistency required. Mixing can be done with a paddle fitted to
Density (Kg/m3) 1060 a drilling machine.
Compressive strength ( N/mm2) Typical propertes are as follows :
ASTM D695 60
Compressive strength (N/mm2)
Tensile strength (N/mm2) @ 7 days : 50
ASTM C307 - 94 20
Tensile strength ( N/mm2) : 3-4
Flexural strength (N/mm2)
BS6319 Part 3 45 Flexural strength ( N/mm2) : 10

Cleaning
Chemical resistance
All tools and equipment should be cleaned immediately after
Conbextra EP10(M) is resistant to oil, grease, fats, most chemi- use with Nitoflor Sol. Spillages should be absorbed with sand
cals, mild acids and alkalis, fresh and sea water. or sawdust and disposed in accordance with local regulations.

Pot life

Ambient temperature affects the time for which bulk material

will remain fluid.
Conbextra EP10(M)

Typical values in minutes @ 270C

Conbextra EP10(M) 50

page 1 of 2
Conbextra EP10(M)

Limitations
Temperature immediately with a resin removing cream, followed by soap
and water. Do not use solvent. In case of contact with eyes,
During application
rinse immediately with plenty of clean water and seek medical
Grouting may be carried out without special precautions at attention immediately - do not induce vomiting.
ambient temperatures from 50 to 350C.
Fire
In service
Nitoflor Sol is flammable. In the even of fire extinguish with
The cured material is suitable for use from 00C. CO2 or foam.

Estimating Flash point : 330C

Packaging Keep away from sources of ignition - no smoking. Wear suit-

able protective clothing, gloves and eye/face protection. Use
Conbextra EP10(M) : 1.5 litre packs
only in well ventillated area.
Storage
Additional information
All Conbextra EP10(M) products has a shelf life of 12 months
The Fosroc range of associated products include high strength
in unopened container under normal warehouse conditions.
cementitious, epoxy grout, polyester resin based mortar for
Precautions
rapid presetting of steel shims to level or for direct bedding
Health and Safety of small base plates; Resin Anchoring systems for same day
anchoring of bolts in drilled holes in concrete or rock. Also
Conbextra EP10(M) : Contains resins which may cause sensi-
available a range of products for use in construction; viz., ad-
tisation by skin contact. Avoid contact with skin and eyes and
mixtures, curing compounds, release agents, flooring systems
inhalation of vapour. Wear suitable protective clothing, gloves
and repair mortars.
and eye/face protection. Barrier creams provide additional
skin protection. Should accidental skin contact occur, remove Separate datasheets are available on these products.

Important note :
Fosroc products are guaranteed against defective materials and manufacture and are sold
subject to its standard terms and conditions of sale, copies of which may be obtained on
request. Whilst Fosroc endeavours to ensure that any advice, recommendation specification
or information it may give is accurate and correct, it cannot, because it has no direct or
continuous control over where or how its products are applied, accept any liability either
Fosroc Chemicals directly or indirectly arising from the use of its products whether or not in accordance with
any advice, specification, recommendation or information given by it.
(India) Pvt. Ltd.
Head Office telephone fax e-mail
Embassy Point, No. 150,
2nd Floor, Infantry Road, +91 80-42521900 +91 80-22281510 [email protected]
Bangalore 560 001,
Karnataka

Regional Offices

Chennai Mumbai Noida Kolkata

Hills Centre,Old No 5, MBC Park, 12th floor, Office No.12B, Unit No. 601, Highway Tower-II 304, Jodhpur Park
New No 9, 3rd Cross Street, ‘D’ Block, Near G Corp/Hyper City A-13/2, 6th Floor, Sector– 62 Kolkata 700 068
Jeth Nagar, Raja Annamalaipuram, Kasarwadawali, Ghodbunder Road, Gautam Buddha Nagar, Ph:+91 33-65343188
Chennai 600 028. Thane (West) 400 615 Noida 201 309, Uttar Pradesh Fax: 033-2499-0280
Ph: +91 44 61304500 Ph: +91 22 6229 6800 Ph: +91 120 6121900
Fax: 022 62296809 Fax: 0120-4270622

www.fosroc.com
page 2 of 2 INDIA/2020/0315/B