Free Questions for H35-481_V2.
0 by dumpssheet
Shared by Hicks on 29-01-2024
For More Free Questions and Preparation Resources
Check the Links on Last Page
Question 1
Question Type: MultipleChoice
Which of the following commands is used to map DSCPs and VLAN priorities?
Options:
A- MOD PHBMAP
B- SET DSCPMAP
C- MOD DSCPMAP
D- SET PHBMAP
Answer:
D
Explanation:
The SET PHBMAP command is used to map DSCPs and VLAN priorities. This command is used to configure the PHB mapping table for
DSCP and VLAN priority, which will determine how the network will prioritize traffic.
https://www.etsi.org/deliver/etsi_tr/121900_121999/121915/15.00.00_60/tr_121915v150000p.pdf
ETSI TR 121 915 V15.0.0 (2019-10)
https://www.etsi.org/deliver/etsi_tr/121900_121999/121915/15.00.00_60/tr_121915v150000p.pdf
https://www.techtarget.com/searchnetworking/feature/5G-NSA-vs-SA-How-does-each-deployment-mode-differ
5G NSA vs. SA: How does each deployment mode differ? | TechTarget
https://www.techtarget.com/searchnetworking/feature/5G-NSA-vs-SA-How-does-each-deployment-mode-differ
https://ngmn.org/wp-content/uploads/Publications/2018/180220_NGMN_PreCommTrials_Framework_definition_v1_0.pdf
definition of the testing framework for the ngmn 5g pre-commercial ...
https://ngmn.org/wp-content/uploads/Publications/2018/180220_NGMN_PreCommTrials_Framework_definition_v1_0.pdf
Question 2
Question Type: MultipleChoice
Which of the following boards is added, the base station Is reset and you need to log in to the LMT again?
Options:
A- OUMPT
B- UBBP
C- UPEU
D- UEIU
Answer:
B
Explanation:
The UBBP board is added to the base station when it is reset, and you need to log in to the LMT again in order to access the new UBBP
board. The UBBP board is used for configuration, monitoring, and maintenance of the base station.
https://www.gsma.com/futurenetworks/wiki/5g-implementation-guidelines/
5G Implementation Guidelines: NSA Option 3 - Future ... - GSMA
https://www.gsma.com/futurenetworks/wiki/5g-implementation-guidelines/
https://arxiv.org/pdf/2202.01032
Understanding O-RAN: Architecture, Interfaces, Algorithms, Security ...
https://arxiv.org/pdf/2202.01032
https://www.fcc.gov/file/18918/download
Report on Risks to 5G from Legacy Vulnerabilities and Best ...
https://www.fcc.gov/file/18918/download
According to Huawei's official documentation, when the UBBP (Universal Baseband Processing) board is added, the base station is
reset and you need to log in to the LMT (Local Management Terminal) again. The addition of other boards (OUMPT, UPEU, UEIU) may
not require a reset and re-login.
Question 3
Question Type: MultipleChoice
Which of the following slots retains the same physical position on both the BBU5900 and BBU3910?
Options:
A- SIot6
B- SIot2
C- Slot7
D- Slot1
Answer:
D
Explanation:
The Slot1 on both the BBU5900 and BBU3910 retains the same physical position. Slot1 is used for the O&M interface, and is used for
communication between the BBU and the OSS. It supports the SFP/SFP+ optical modules for O&M communication.
Question 4
Question Type: MultipleChoice
In NSA networking, which of the following factors affect the downlink peak rate of a CPE?
Options:
A- Downlink transmit power of the NR base station
B- Uplink transmit power of the CPE
C- Downlink BLER of 3% or above
D- CPE location
Answer:
A, C, D
Explanation:
In Non-standalone (NSA) networking, the downlink peak rate of a CPE is affected by various factors, such as the downlink transmit
power of the NR base station, the CPE location, the quality of the radio channel, and the configuration of the network. -The downlink
transmit power of the NR base station affects the signal strength received by the CPE and therefore can affect the peak rate achieved. -
The CPE location in relation to the base station can affect the signal strength and quality of the radio channel. If the CPE is located
farther away from the base station or in an area with high radio interference, it may result in a lower peak rate. -Downlink BLER of 3% or
above can result in retransmission and thus lower peak rate. -Uplink transmit power of the CPE does not affect the downlink peak rate of
CPE as it is only related to uplink transmission.
Question 5
Question Type: MultipleChoice
In NSA networking, X2 self-setup between a gNodeB and an eNodeB requires that the gNodeB and eNodeB be managed by the same
OSS.
Options:
A- True
B- False
Answer:
A
Explanation:
In Non-standalone (NSA) networking, X2 self-setup between a gNodeB and an eNodeB requires that the gNodeB and eNodeB be
managed by the same OSS. Because gNodeB and eNodeB are managed by the same OSS, the OSS can configure the X2 self-setup
parameters, such as the X2 self-setup switch, the X2 interface IP address, and the X2 self-setup trigger conditions. Only when the
gNodeB and eNodeB are managed by the same OSS and configured with the same X2 self-setup parameters, the gNodeB and eNodeB
can establish an X2 self-setup connection.
Question 6
Question Type: MultipleChoice
Generally, the gNodeB synchronizes time information from the OSS. Which of the following commands is used to configure the IP
address of the time server?
Options:
A- ADD IPCLKUNK
B- ADD GPS
C- ADD NTPC
D- ADD OMCH
Answer:
C
Explanation:
In a gNodeB, the time information is synchronized from the OSS using the Network Time Protocol (NTP). The ADD NTPC command is
used to configure the IP address of the NTP server, which is the time server that the gNodeB synchronizes with. This command is used
to specify the IP address of the NTP server, the NTP version, and other parameters related to time synchronization.
To Get Premium Files for H35-481_V2.0 Visit
https://www.p2pexams.com/products/h35-481_v2.0
For More Free Questions Visit
https://www.p2pexams.com/huawei/pdf/h35-481-v2.0
